American Outdoor 30NB-00SP Le manuel du propriétaire

Marque: American Outdoor

Modèle: 30NB-00SP

Catégorie: Barbecues

Taper: Le manuel du propriétaire

REV 7 - 0909081534

L-C2-17909

SAFETY WARNINGS & CODES

INSTALLER: Leave these instructions with consumer.

CONSUMER: Retain for future reference.

INSTALLATION AND OPERATING

INSTRUCTIONS

Important: Read these instructions carefully

before starting installation.

DANGER

IF YOU SMELL GAS:

1. Shut off the gas to the appliance.

2. Extinguish any open ﬂ ame.

3. Open lid if equipped with an oven.

4. If odor continues, keep away from the

appliance, and immediately call the gas

supplier or ﬁ re department.

WARNING

1. Do not store or use gasoline or other

ﬂ ammable vapors and liquids in the

vicinity of this or any other appliance.

2. A propane cylinder not connected for use

shall not be stored in the vicinity of this

or any other appliance.

CODE AND SUPPLY REQUIREMENTS: This

barbecue must be installed in accordance with

local codes and ordinances, or, in the absence of

local codes, with either the latest National Fuel Gas

Code (ANSI Z223.1/NFPA 54), and Natural Gas and

Propane Installation Code (CSA-B149.1).

This appliance and its individual shutoff valves must

be disconnected from the gas supply piping system

when testing the system at pressures in excess of

½ psig (3.5 kPa).

This appliance must be isolated from the gas supply

piping system by closing its individual manual

shutoff valves during any pressure testing of the

gas supply system at pressures up to and including

½ psig (3.5 kPa).

All electrical outlets in the vicinity of the barbecue

must be properly grounded in accordance with local

codes or, in the absence of local codes, with the

National Electrical Code, ANSI/NFPA 70, or the

Canadian Electrical Code, CSA C22.1, whichever

is applicable.

Keep all electrical supply cords and fuel supply

hoses away from any heated surface.

Certiﬁ ed to ANSI: Z21.58-2007 / CSA 1.6-2007

WARNING

Improper installation, adjustment, alteration,

service, or maintenance can cause injury

or property damage. Refer to this manual.

For assistance or additional information,

consult a qualiﬁ ed professional installer,

service agency, or the gas supplier.

24, 30, and 36 SERIES

OUTDOOR GAS BARBECUES

SLIDE-IN MODEL

ROBERT H. PETERSON CO. • 14724 East Proctor Avenue • City of Industry, CA 91746

REV 7 - 0909081534

L-C2-17909

AVERTISSEMENTS ET CODES DE SÛRETÉ

INSTALLATEUR: Laissez ces instructions avec le

consommateur.

CONSOMMATEUR: Maintenez pour la future référence.

INSTALLATION ET CONSIGNES

D’UTILISATION

DANGER

S’il y a une odeur de gaz:

1. Coupez l’admission de gaz de l’appareil.

2. Éteindre toute ﬂ amme nue.

3. Ouvrir le couvercle.

4. Si l’odeur persiste, gardez loin de l’appareil,

et appelez immédiatement le fournisseur de

gazou le service d’incendie.

AVERTISSEMENT

1. Ne pas entreposer ni utiliser de l’essence ni

d’autres vapeurs ou liquides inﬂ ammables

dans le voisinage de l’appareil, ni de

proximité de tout autre appareil.

2. Une bouteille de propane qui nest pas

raccordée en vue de son utilisation, ne doit

pas être entreposée dans le voisinage de

cet appareil ou de tout autre appareil.

CONDITIONS DE CODE ET D’APPROVISIONNEMENT:

Ce barbecue doit être installé selon des codes et des

ordonnances locaux, ou, en l’absence des codes

locaux, avec l’un ou l’autre le plus défunt code national

de gaz de carburant (norme ANSI Z223.1/NFPA 54),

et le code d’installation de gaz naturel et de propane

(CSA-B149.1).

Cet appareil et ses différents robinets d’isolement

doivent être démontés du système sifﬂ ant d’offre de gaz

en examinant le système aux pressions au-dessus du

½ psig (kPa 3.5).

Cet appareil doit être isolé dans le système sifﬂ ant d’offre

de gaz par fermeture ses différents robinets d’isolement

manuels pendant tous les essais sous pression du circuit

d’alimentation de gaz aux pressions jusques et y compris

le ½ psig (kPa 3.5).

Toutes les sorties électriques à proximité du barbecue

doivent être correctement fondues selon des codes

locaux ou, en l’absence des codes locaux, avec le code

électrique national, ANSI/NFPA 70, ou le code électrique

canadien, CSA C22.1, qui est jamais applicable.

Gardez tout cordon d’alimentation électrique et tuyau

d’alimentation en combustible a l’écart des surfaces

chauffées.

Certiﬁ é à la norme ANSI: Z21.58-2007 / CSA 1.6-

2007

24, 30 et 36 SÉRIES

LE GAZ EXTÉRIEUR GRILLE TOUT

ENTIER LE MODÈLE DE SLIDE-IN

AVERTISSEMENT

L’installation inexacte, l’ajustement, le

changement, le service ou l’entretien

peuvent causer des dommages ou des

dégats matériels. Référez-vous à ce manuel.

Pour l’aide ou l’information additionnelle

consultez un installateur qualiﬁ é et

professionnel, l’agence de service, ou le

fournisseur de gaz.

Important: Lisez ces instructions soigneusement

avant de commencer l’installation.

ROBERT H. PETERSON CO. • 14724 East Proctor Avenue • City of Industry, CA 91746

REV 7 - 0909081534

L-C2-17909

TABLE OF CONTENTS

PRODUCT DATA TABLE

Table 1 - Product data table

SAFETY WARNINGS & CODES 1

PRODUCT DATA TABLE 3

PARTS LIST 5

ROTISSERIE PARTS LIST 7

PLANNING THE LOCATION OF THE BARBECUE 8

ENSURING PROPER COMBUSTION AIR AND COOLING AIR FLOW 8

ELECTRICAL OUTLETS 8

EXHAUST REMOVAL 8

INSTALLATION 8

SAFE USE & MAINTENANCE OF PROPANE-GAS CYLINDERS 9

CHECKING AND CONVERTING GAS TYPE 11

INSTALLING THE REGULATOR 11

CHECKING AND CONVERTING THE REGULATOR 11

CHECKING/CONVERTING THE BURNER ORIFICES 12

MAIN BURNER ORIFICE SIZE CHECKING/CONVERSION 12

MAIN BURNER AIR SHUTTER ADJUSTMENT 12

BACKBURNER ORIFICE SIZE CHECKING/CONVERSION (IF EQUIPPED) 13

BARBECUE SAFETY INFORMATION & MAINTENANCE 15

DRIP COLLECTION SYSTEM 15

LIGHTING (IGNITION) INSTRUCTIONS 17

ROTISSERIE INSTRUCTIONS 18

USING THE BACKBURNER AND ROTISSERIE 18

PUTTING THE MEAT ON THE SPIT ROD 18

RUNNING THE ROTISSERIE 18

REPLACING THE IGNITOR BATTERY 19

TROUBLESHOOTING 19

ACCESSORIES 20

THE VAPORIZER PANEL(S) 20

THE DRIP PAN 20

THE WARMING RACK 20

CARE & CLEANING 21

COVER 21

AMERICAN OUTDOOR GRILL LIMITED WARRANTY

Speciﬁ cation Value

Backburner (if equipped)

BTU per burner

10,000 (2.9 kw)

Natural gas oriﬁ ce

#54 (1.397 mm)

Propane gas oriﬁ ce

#65 (0.889 mm)

Speciﬁ cation Value

Main Burner 24" model

Counter opening height*

" (21 cm)

Counter opening width*

" (35.8 cm)

Counter opening depth*

" (15.2 cm)

BTU per burner

16,000 (4.7 kw)

Natural gas oriﬁ ce

#46 (2.057 mm)

Propane gas oriﬁ ce

#1.20 (1.20 mm)

*Note: If using an insulating liner,

consult the liner instructions for

counter cut-out dimensions.

Speciﬁ cation Value

Main Burner 30" model

Counter opening height*

" (21 cm)

Counter opening width*

" (35.8 cm)

Counter opening depth*

" (15.2 cm)

BTU per burner

16,000 (4.7 kw)

Natural gas oriﬁ ce

#46 (2.057 mm)

Propane gas oriﬁ ce

#1.20 (1.20 mm)

Speciﬁ cation Value

Main Burner 36" model

Counter opening height*

" (21 cm)

Counter opening width*

" (35.8 cm)

Counter opening depth*

" (15.2 cm)

BTU per burner

16,000 (4.7 kw)

Natural gas oriﬁ ce

#46 (2.057 mm)

Propane gas oriﬁ ce

#1.20 (1.20 mm)

REV 7 - 0909081534

L-C2-17909

AVERTISSEMENTS

Avertissements généraux :

• Ce barbecue est pour ultilisation à l’extérieur seulement. Si l’appareil est entreposé à l’intérieur,

enlever les bouteilles et les laisser à l’extérieur.

• Ne pas ranger le gril immédiatement aprés l’avoir utilisé. le laisser refroidir avant de le déplacer

ou de la ranger. Le non respect de cette mesure de sécurité pourrait entraîner un incendie

causant des dommages à la propriété, des blessures ou la mort.

• Ne pas utiliser cet appareil sous une surface combustible.

• Ne pas utiliser cet appareil sous un auvent. Le non respect de cette mesure de sécurité pourrait

entraîner un incendie ou des blessures.

• Dégagement minimal entre les parois latérales et l’arriére de l’appareil et la construction

combustible (45.7 cm à partir des parois latérales et 45.7cm à partir de l’arriére).

• Le régulareur de pression de gaz prévu avec cet appareil de cuisson à gaz pour l’extérieur

doit être utilisé. Ce régulateur est réglé pour une pression de sortie de 5 pouces de colonne

de l’eau pour le gaz naturel, et 10 pouces pour le propane.

• LE RÉGULATEUR INCLUS D’APPAREILS EST ÉVALUÉ POUR LE MAXIMUM DE

(LIVRES

PAR POUCE CARRÉ). SI VOTRE OFFRE DE GAZ EST

PLUS GRAND QUE (LIVRES

PAR POUCE CARRÉ), UN RÉGULATEUR ADDITIONNEL DOIT ÊTRE INSTALLÉ AVANT LE

BARBECUE. VOIR LA SECTION DE CONDITIONS D’OFFRE DE GAZ POUR LA PRESSION

APPROPRIÉE D’OFFRE DE GAZ.

• Ne couvrez jamais la surface entière de cuisine ou de gril de gauffreuses ou de casseroles.

La surchauffe se produira et les brûleurs ne seront pas très performants quand la chaleur de

combustion est emprisonnée au-dessous de la surface à cuire.

• Ne pulvérisez jamais l’eau sur une unité chaude de gaz, comme ceci peut endommager des

composants de porcelaine ou de fer de fonte.

Avertissements de propane :

• Une fuite de GPL peut causer une incendie ou une explosion si enﬂ ammée entraînant des

blessures corporelles graves ou la mort.

• Communiquez avec le fournisseur de GPL pour les réparations ou pour disposer de qules

bouteille ou du GPL non utilisé.

REV 7 - 0909081534

L-C2-17909

PARTS LIST

IMPORTANT

This AOG oven and backburner (if equipped)

are fully pre-assembled and tested at the

factory.

DO NOT attempt to remove the oven and

backburner from the barbecue prior to

or during installation or damage to the

connecting gas line and ignitor wiring may

occur.

The plastic straps that secure the oven to

the barbecue unit must be removed and

discarded prior to lighting the barbecue.

This note applies for all 3 size (24", 30",

36") models.

Replacement parts can be ordered

from your local AOG dealer.

24" Model shown

Item Part # Description

1. 24-B-11 Cooking grids 24" (Set of 2)

2. 24-B-05 Vaporizer panels 24" (2)

3. 24-B-06 Main burner (2)

4. 24-B-10 Thermometer

5. 24-B-25 Oven 24"

6. 24-B-02 Warming rack 24" *

7. 3083 Drip tray with match holder

8. 24-B-26 Barbecue face 24"

9. 3199-34 Electronic ignitor

10. 24-B-08 Burner manifold 24"

11. 24-B-15 Heat shield 24" (1)

12. 24-B-04 Main burner electrode 24" (2)

13. 3015 Barbecue knobs 24" (2)

14. 3016 Backburner knob *

15. 24-B-17 Backburner *

16. PR-4 Regulator

* if equipped

REV 7 - 0909081534

L-C2-17909

PARTS LIST (Cont.)

30" Model shown

Item Part # Description

1. 30-B-11 Cooking grids 30" (Set of 3)

30-B-05-03

Vaporizer panels 30" (Set of 3)

3. 24-B-06 Main burner (3)

4. 24-B-10 Thermometer

5. 30-B-25 Oven 30"

6. 30-B-02 Warming rack 30" *

7. 3083 Drip tray with match holder

8. 30-B-26 Barbecue face 30"

9. 3199-34 Electronic ignitors (2)

10. 30-B-08 Burner manifold 30"

11. 30-B-15 Heat shield 30" (Set of 2)

12. 24-B-04 Main burner electrode 30" (3)

13. 3015 Barbecue knobs (3)

14. 3016 Backburner knob *

15. 24-B-17 Backburner *

16. PR-4 Regulator

* if equipped

REV 7 - 0909081534

L-C2-17909

Item

No.

Part

No.

Description

A. 24-B-07 Stainless steel motor

B. 24-B-18 Spit prongs (set of 2)

C. 24-B-13 Spit rod

" hex 24"

or 30-B-13 Spit rod

" hex 30"

or 36-B-13 Spit rod

" hex 36"

D. 24-B-09 Handle knob

ROTISSERIE KIT

ROTISSERIE PARTS LIST (IF EQUIPPED)

36" Model shown

PARTS LIST (Cont.)

Item Part # Description

1. 36-B-11 Cooking grids 36" (Set of 3)

2. 36-B-05 Vaporizer panels 36" (3)

3. 24-B-06 Main burner (3)

4. 24-B-10 Thermometer

5. 36-B-25 Oven 36"

6. 36-B-02 Warming rack 36" *

7. 3083 Drip tray with match holder

8. 36-B-26 Barbecue face 36"

9. 3199-34 Electronic ignitors (2)

10. 36-B-08 Burner manifold 36"

11. 36-B-15 Heat shield 36" (Set of 2)

12. 24-B-04 Main burner electrode 36" (3)

13. 3015 Barbecue knobs (3)

14. 3016 Backburner knob *

15. 24-B-17 Backburner *

16. PR-4 Regulator

* if equipped

PLANNING THE LOCATION OF THE BARBECUE

This barbecue is designed for outdoor use only. DO NOT use this unit under unprotected ﬂ ammable surfaces. DO

NOT use this appliance inside a building, garage, or any other unprotected covered area (see EXHAUST REMOVAL

below). DO NOT use this barbecue in or on a recreational vehicle or boat.

Important: This unit is NOT insulated, and therefore the unit, when in operation, must be located with a minimum of

18" (45.7 cm) of side and back clearance from unprotected combustible materials such as wood, plastic, or

stucco with wood framing.

GAS-SUPPLY PLUMBING REQUIREMENTS

For natural gas or a household propane system, rigid

" (1.3

cm) or

" (1.9 cm) black steel pipe or local code-approved

pipe is required to conduct the gas supply to the unit. An

outdoor-approved ﬂ exible connector can be used to connect

the household gas supply to the barbecue. DO NOT use a

rubber hose within the barbecue enclosure. Apply only

joint compounds that are resistant to all gasses on all male

pipe ﬁ ttings. Make sure to tighten every joint securely.

Note: If

" (1.3 cm) pipe is used with natural gas, it

should be no longer than 20' (6.1 meters).

Important: An external valve (with a removable key) in

the gas line is necessary for safety when the

barbecue is not in use. It also provides for

convenient maintenance.

INSTALLATION

GAS SUPPLY AND MANIFOLD PRESSURES

For natural gas - Normal 7" water column (w.c.), minimum

5" w.c., maximum 10

" w.c.

For propane gas - Normal 11" w.c., minimum 8" w.c.,

maximum 13" w.c.

ENSURING PROPER COMBUSTION AIR AND

COOLING AIR FLOW

You must maintain proper air ﬂ ow for the barbecue to

perform as it was designed (Fig.

8-1). If airﬂ ow is blocked,

overheating and poor combustion will result. Do not block

the 1" front air inlet along the

bottom of the face or more

than 75% of the cooking grid

surface with objects such as

pans or griddles.

Note: The 1" front air

space allows access to the

drip tray.

ELECTRICAL OUTLETS

All electrical outlets in the

vicinity of the barbecue must be properly grounded.

Note: Keep electrical supply cords away from all heated

surfaces.

EXHAUST REMOVAL

If installed or used under a patio roof, the cooking grid area

must be fully covered by a chimney and exhaust hood.

An exhaust fan with a rating of 1,000 CFM (cubic feet per

minute) or more may be necessary to efﬁ ciently remove

smoke and other cooking by-products from the covered

area. This barbecue shall not be used under unprotected

overhead combustible construction. THIS UNIT SHOULD

NOT BE LOCATED IN A FULLY ENCLOSED AREA OF

ANY KIND.

CAUTION: Wind blowing into or across the rear oven lid

vent (Fig. 8-2) can cause poor performance

and/or dangerous overheating. Orient the

grill so that the prevailing wind blows toward

the front of the grill (Fig. 8-3).

CAUTION: To prevent dangerous overheating, the rear

of the unit must have a minimum clearance

of 4" from any backsplash/wall.

Fig. 8-1

Ventilation Diagram

Fig. 8-3

CORRECT

PLACE GRILL SO PREVAILING WIND

BLOWS TOWARD FRONT OF GRILL

YOU MUST PROTECT REAR OVEN

VENT FROM PREVAILING WIND

Rear oven lid vent

INCORRECT

Fig. 8-2

Test all gas connections under pressure with a half-and-

half soap and water solution. If bubbles appear, there is

a leak. Turn off the gas and tighten the connections. Then

turn on the gas and repeat the leak test. Repeat until no

leaks are detected. Never use an open ﬂ ame to test

for leaks.

Important: This unit is NOT insulated, and therefore if an approved insulating liner is not added, the unit must be located

with a minimum of 18" (45.7 cm) of side and back clearance from unprotected combustible materials such

as wood, plastic, or stucco with wood framing, when in operation.

For household gas systems the suppplied regulator must

be attached to the gas line before connecting, turning on,

and testing the gas connection as outlined in this section.

Remove the red safety tag from the manifold input and use

a ﬂ ex connector and steel pipe to connect to the regulator

and supply as required. Attaching a ﬂ ex connector directly

to the manifold will allow the convertible regulator to be

located outside the unit for easy access.

The regulator supplied with this unit uses female

" NPT

threads at both ends. The manifold input uses male

NPT threads.

Important: If you have a household propane supply,

convert the regulator to use propane

gas by following the instructions in

the section entitled CHECKING AND

CONVERTING THE REGULATOR.

Test all gas connections under pressure with a half-and-half

soap and water solution. If bubbles appear, there is a leak.

Turn off the gas and tighten the connections. Then turn on

the gas and repeat the leak test. Repeat until no leaks are

detected. Never use an open ﬂ ame to test for leaks.

ReaRear or ovenven li lid vd ventent

COCORRRRECECTT

GAS SUPPLY AND MANIFOLD PRESSURES

For natural gas - Normal 7" water column (w.c.), minimum

5" w.c., maximum 10

" w.c.

For propane gas - Normal 11" w.c., minimum 8" w.c.,

maximum 13" w.c.

Fig. 9-1 Type I Acme thread quick coupler

Pressure

relief

valve

QCC

Type 1

valve

Brass Acme

thread ﬁ tting

Liquid level

indicator

(optional)

Hand nut with Acme

thread

Regulator

Vent

Hose

Hand wheel

The use of pliers or a wrench should not be necessary. Only

cylinders marked “propane” may be used.

To disconnect: Turn the hand nut counterclockwise until

detached (Fig. 9-1).

Important: Before using the unit, and after each time the

cylinder is removed and reattached, check

the hose for wear (see a.) and check all

connections for leaks. Turn off the unit valves

and open the main cylinder valve, then check

connections with soapy water. Repair any

leaks before lighting the unit.

CAUTION: Always turn the propane cylinder main valve

off after each use, and before moving the unit

and cylinder or disconnecting the coupling.

This valve must remain closed and the

cylinder disconnected while the appliance

is not in use, even though the gas ﬂ ow is

stopped by a safety feature when the coupler

is disconnected.

Carefully inspect the hose assembly each time before the

gas is turned on. A cracked or frayed hose should be replaced

immediately.

If the appliance is stored indoors, the cylinder must be

disconnected and removed. Disconnected

cylinders must be

stored outdoors, out of the reach of children, with threaded

valve plugs tightly installed, and must not be stored in a

building, garage, or any other enclosed area.

FOR YOUR SAFETY

a. DO NOT store a spare propane-gas cylinder under or

near this appliance.

b. NEVER ﬁ ll the cylinder beyond 80-percent full.

c. IF THE INFORMATION IN a. AND b. IS NOT FOLLOWED

EXACTLY, A FIRE CAUSING DEATH OR SERIOUS

INJURY MAY OCCUR.

IMPORTANT FOR YOUR SAFETY

READ AND FOLLOW ALL WARNINGS PROVIDED WITH THE PROPANE-GAS CYLINDER.

When operating this appliance with a propane-gas cylinder, these instructions and warnings MUST be observed.

FAILURE TO DO SO MAY RESULT IN A SERIOUS FIRE OR EXPLOSION.

CYLINDER/CONNECTOR REQUIREMENTS

a. Propane-gas cylinders, valves, and hoses must be

maintained in good condition and must be replaced if

there is visible damage to either the cylinder or valve. If the

hose is cut or shows excessive abrasion or wear, it must

be replaced before using the gas appliance (see e.).

b. This unit, when used with a cylinder, should be connected

to a standard 5-gallon (20 lb.) propane-gas cylinder

equipped with an OPD (Overﬁ ll Prevention Device).

The OPD has been required on all cylinders sold since

October 1,1998, to prevent overﬁ lling.

c. Cylinder dimensions should be approximately 12" (30.5

cm) in diameter and 18" (45.7 cm) high. Cylinders must

be constructed and marked in accordance with the

Speciﬁ cations for Propane Gas Cylinders of the U.S.

Department of Transportation (D.O.T.) or the National

Standard of Canada, CAN/CSA-B339, Cylinders,

Spheres, and Tubes for Transportation of Dangerous

Goods.

d. The cylinder used must include a collar to protect the

cylinder valve, and the cylinder supply system must be

arranged for vapor withdrawal.

e. The pressure regulator and hose assembly (Fig. 9-1)

supplied with this outdoor-cooking gas appliance must

be used. Original and replacement pressure regulator

and hose assemblies must be those speciﬁ ed by the

manufacturer for connection with a cylinder connecting

device identiﬁ ed as Type I by the ANSI Z 21.58-2005/CGA

1.6-2005 (see PARTS LIST for ordering information).

f. The propane-gas cylinder valve must be equipped with a

cylinder connection coupling device, described as Type

I in the standard deﬁ ned in paragraph e. above. This

device is commonly described as an Acme thread quick

coupler.

g. If the propane-gas cylinder comes with a dust plug, place

the dust cap on the cylinder valve outlet whenever the

cylinder is not in use.

QUICK COUPLER OPERATION

To connect the regulator/hose assembly to the propane-

gas cylinder valve ﬁ tting: Press the hand nut on the regulator

over the Acme thread ﬁ tting on the cylinder valve. Turn the hand

nut clockwise to engage the threads and tighten until snug.

ENCLOSURE REQUIREMENTS

FOR YOUR SAFETY, you must provide the openings listed below for drainage, replacement air, and cross-ventilation

of any storage area exposed to possible leakage from gas connections, the unit, or propane cylinders:

One side of the gas cylinder enclosure left completely open to the outside OR by providing four (4) ventilation

openings. Two (2) openings are to be at the cylinder valve level (approx. 16" [40.6 cm] above the ﬂ oor) and on

opposite walls of the enclosure. Two (2) more openings must be at the ﬂ oor level on opposite sides of the enclosure.

The ﬂ oor-level openings must start at the ﬂ oor and shall extend no higher than 5" (12.7 cm) above the ﬂ oor. Each

opening must have a minimum of 10 sq. in. (64.5 cm

) of free area. To achieve the proper ventilation, you may drill

a series of holes, omit the grout from masonry joints, or replace a brick with a hardware cloth screen. If the ﬂ oor

in the cabinet is raised and the space beneath the cabinet is open to the outside, the lower ventilation openings

may be in the ﬂ oor.

Consult your gas supplier for ventilation and regulator requirements when connecting to a household propane supply.

e. The pressure regulator and hose assembly used must

match the speciﬁ cation for Type I by ANSI Z 21.58-2005/

CGA 1.6-2005 (see Fig. 9-1).

SAFE USE & MAINTENANCE OF PROPANE GAS CYLINDERS

Fig. 10-1 type coupleur rapide de ﬁ l de point culminant d’I

Valve

décompression

QCC

Type 1

Valve

Ajustage de précision

en laiton de ﬁ l de

point culminant

Indicateur

de niveau

de liquide

(facultatif)

Écrou de main avec le

ﬁ l de point culminant.

Régulateur

Passage

Tuyau

Volant de commande

main dans le sens des aiguilles d’une montre pour engager les

ﬁ ls et pour serrer jusqu’à ce que douillettement. L’utilisation des

pinces ou de la clé ne devrait pas être nécessaire. Seulement

le propane marqué par cylindres doit être employé.

Pour débrancher: Tournez l’écrou de main dans le sens

contraire des aiguilles d’une montre jusqu’à isolé (ﬁ g. 10-1).

Important: Avant d’employer le gril, et ensuite chaque

fois que le cylindre est enlevé et rattaché,

examinez tous les raccordements pour déceler

les fuites. Arrêtez les valves de gril et ouvrez

la valve principale de cylindre, puis vériﬁ ez

les raccordements avec de l’eau savonneux.

Réparez toutes les fuites avant d’allumer le gril.

ATTENTION: Tournez toujours la valve principale de cylindre

de propane au loin après chaque utilisation,

et avant de déplacer le gril et le cylindre, ou

débrancher l’accouplement. Cette valve doit

rester fermée et le cylindre a débranché alors

que l’appareil n’est pas en service, quoique

l’écoulement de gaz soit arrêté par un dispositif

de sûreté quand le coupleur est débranché.

Inspectez soigneusement l’ensemble de tuyau chaque fois

avant que le gaz soit allumé. Un tuyau criqué ou frangé devrait

être remplacé immédiatement.

Si l'appareil est stocké à l'intérieur, le cylindre doit être disconnected

et a enlevé. Des cylindres Disconnected doivent être stockés

dehors, hors de la portée des enfants, avec les prises de valve

ﬁ letées étroitement installées, et ne doivent pas être stockés dans

un bâtiment, le garage, ou n'importe quel autre secteur inclus.

POUR VOTRE SÛRETÉ

a. Ne stockez pas un cylindre de gaz disponible de propane

dessous ou ne vous approchez pas de cet appareil.

b. Ne remplissez jamais cylindre au delà de 80 pour cent de

plein.

c. SI L’INFORMATION DANS “A” ET “B” N’EST PAS SUIVIE

EXACTEMENT, UN FEU CAUSANT LA MORT OU DES

DOMMAGES SÉRIEUX PEUT SE PRODUIRE.

IMPORTANT POUR VOTRE SÛRETÉ

LISEZ ET SUIVEZ TOUS LES AVERTISSEMENTS ÉQUIPÉS DE VOTRE CYLINDRE DE GAZ DE PROPANE.

En actionnant cet appareil avec un cylindre de gaz de propane ON DOIT observer ces instructions et avertissements.

LE MANQUE DE FAIRE AINSI PEUT AVOIR COMME CONSÉQUENCE UNE INCENDIE OU UNE EXPLOSION SÉRIEUSE.

CYLINDRE ET CONDITIONS ET

CARACTÉRISTIQUES DE CONNECTEUR

a. Des cylindres et les valves de gaz de propane doivent être

maintenus en bon état et doivent être remplacés s’il y a

des dommages évidents au cylindre ou à la valve.

b. Ce gril, une fois utilisé avec un cylindre, devrait être relié à

un gallon de la norme 5 (20lb.) cylindre de gaz de propane

équipé d’un OPD (remplissez au-dessus du niveau le

dispositif d’empêchement). L’OPD a été exigé sur tous les

cylindres vendus depuis octobre 1.1998 pour empêcher le

remplissage excessif.

c. Les dimensions de cylindre devraient être approximativement

12"(30.5cm) de diamètre et 18" (45.7cm) hauts. Des

cylindres doivent être construits et marqués selon les

caractéristiques pour des cylindres de gaz de propane du

département des ETATS-UNIS du transport (D.O.T.) ou

le niveau national du Canada, du CAN/CSA-B339, des

cylindres, des sphères et des tubes pour le transport des

marchandises dangereuses.

d. Le cylindre doit inclure un collier pour protéger la valve

de cylindre et le circuit d’alimentation de cylindre doit être

assuré le retrait de vapeur.

e. Le régulateur de pression et l’ensemble de tuyau (

ﬁ g. 10-

) fourni avec cet appareil à cuire extérieur de gaz doivent

être utilisés. Les régulateurs d’original et de pression de

remplacement et les ensembles de tuyau doivent être ceux

indiqués par le fabricant pour le raccordement avec un

dispositif se reliant de cylindre identiﬁ é comme type I par la

norme ANSI Z 21.58-2007/CGA 1.6-2007 avec la norme ANSI

Z 21.58a -1998 d’addenda et CGA 1.6a - M98.

f. La valve de cylindre de gaz de propane doit être équipée

d’un dispositif d’accouplement de raccordement de

cylindre, décrit comme type I dans la norme déﬁ nie dans le

e. de paragraphe ci-dessus. Ce dispositif est généralement

décrit comme coupleur rapide de ﬁ l de point culminant.

g. Si votre cylindre de gaz de propane vient avec une prise

de la poussière, placez le bouchon anti-poussière sur la

sortie de valve de cylindre toutes les fois que le cylindre

n’est pas en service.

OPÉRATION DE COUPLEUR RAPIDE

Pour relier le regulator/hose à l’ajustage de précision de

valve de cylindre de gaz de propane: Serrez l’écrou de main

sur le régulateur au-dessus de l’ajustage de précision de ﬁ l

de point culminant sur la valve de cylindre. Tournez l’écrou de

CONDITIONS DE CLÔTURE

POUR VOTRE SÛRETÉ, vous devez fournir les ouvertures suivantes ci-dessous pour le drainage, l’air de rechange, et

la ventilation en travers de n’importe quelle zone de stockage exposée à la fuite possible des raccordements de gaz,

du gril, ou du cylindre de propane:

Un côté de la clôture de cylindre de gaz a laissé complètement ouvert de extérieur OU en fournissant quatre (4)

ouvertures de ventilation. Deux ouvertures doivent être au niveau de valve de cylindre (approximativement 16" (40.6

centimètres) au-dessus du plancher) et sur les murs opposés de la clôture. Deux ouvertures supplémentaires doivent

être au niveau de plancher des côtés opposés de la clôture. Les ouvertures de niveau de plancher doivent commencer

au plancher et se prolongeront pas plus haut que 5"(12.7 centimètre) au-dessus du plancher. Chaque ouverture doit

avoir un minimum de 10 pouces carrés (64.5 cm

) du secteur libre. Pour réaliser la ventilation appropriée, vous pouvez

forer une série de trous, omettez le coulis des joints de maçonnerie, ou remplacez une brique avec un écran de tissu

de matériel. Si le plancher dans le coffret est augmenté et l’espace sous le coffret est ouvert d’extérieur, les ouvertures

inférieures de ventilation peuvent être dans le plancher.

e. Le régulateur de pression et l’ensemble de tuyau utilisé

doivent assortir les spéciﬁ cations pour le type I par ANSI

Z 21.58-2005/CGA 1.6-2005 (voir la ﬁ gue. 10-1).

UTILISATION SÛRE ET ENTRETIEN DES CYLINDRES DE GAZ DE PROPANE

CHECKING AND CONVERTING GAS TYPE

This unit comes from the factory conﬁ gured for

one type of gas, as marked on the label behind the

faceplate.

Converting this unit to burn a different type of

gas requires a conversion kit from the factory.

The professional installer who converts this

unit to burn a different gas must perform the

following functions:

1. Change brass gas orifices (included at original

shipping) on each burner to match the new gas type

(see PRODUCT DATA TABLE, Table 1).

2. Switch the convertible gas regulator (included

at original shipping) to match the new gas type

(see below).

3. Plumb the unit to the new gas supply.

4. Apply a new label behind the faceplate, indicating

the new gas the unit will burn (included with

conversion kit).

HAZARDOUS OVERHEATING WILL OCCUR

IF A NATURAL-GAS ORIFICE IS USED WITH

PROPANE GAS. IF YOU ARE NOT SURE IF THE

CORRECT ORIFICES ARE INSTALLED, OR IF AN

ORIFICE CHANGE IS NECESSARY, REFER TO

THE FOLLOWING INSTRUCTIONS.

CAUTION: Make sure the unit is at a safe

temperature and isolated from gas and

electrical supplies before beginning

the tasks outlined below.

Note: The cooler the unit, the greater the tolerances

between the stainless-steel parts, and

therefore the easier to disassemble and

reassemble parts of the unit.

CAUTION: For your safety, exercise caution and

use adequate hand protection (such

as gloves) when handling potentially

sharp sheet-metal parts.

THIS APPLIANCE REGULATOR IS RATED FOR

PSI MAXIMUM. IF YOUR GAS SUPPLY IS

GREATER THAN

PSI, AN ADDITIONAL REGULATOR MUST BE INSTALLED TO REDUCE

THE INPUT PRESSURE TO THE UNIT to

PSI OR LESS. SEE GAS-SUPPLY REQUIREMENTS

SECTION FOR PROPER GAS-SUPPLY PRESSURE.

CHECKING AND CONVERTING THE REGULATOR

Note: Each end of the plastic converter is engraved with either the letters “NAT”

or “L.P.” (propane) for the respective gasses. When the converter is in the

cap and the cap is held uppermost, the letters seen indicate the gas that

the regulator is set up for.

To convert the regulator from one gas to another, follow steps 1-4.

STEP 2:

Remove the converter (the

plastic stalk) by carefully

pulling it away from the center

of the cap (it will snap out of

its seating).

STEP 1:

Unscrew and remove the cap from the

regulator, extracting the converter.

Regulator: note the cap

on top

STEP 3:

Turn the converter around and

replace it carefully, into the

center of the cap (it will snap

into place). Check that you can

read the type of gas the unit is

set for.

STEP 4:

Replace the unit into the

regulator and screw down

until snug.

Read gas

type here

WARNING

This unit comes from the factory conﬁ gured for

natural gas, as marked on the label behind the

faceplate.

Converting this unit to burn a different type of

gas requires a conversion kit from the factory.

The professional installer who converts this

unit to burn a different gas must perform the

following functions:

1. Change brass gas orifices (included at original

shipping) on each burner to match the new gas type

(see PRODUCT DATA TABLE, Table 1).

2. Switch the convertible gas regulator (included at

original shipping) to match the new gas type (see

below).

3. Plumb the unit to the new gas supply.

4. Apply a new label behind the faceplate, indicating

the new gas the unit will burn and covering the

old gas information.

HAZARDOUS OVERHEATING WILL OCCUR

IF A NATURAL-GAS ORIFICE IS USED WITH

PROPANE GAS. IF YOU ARE NOT SURE IF THE

CORRECT ORIFICES ARE INSTALLED, OR IF AN

ORIFICE CHANGE IS NECESSARY, REFER TO

THE FOLLOWING INSTRUCTIONS.

INSTALLING THE REGULATOR

The regulator must be attached to the unit before

connecting to the gas supply. Attach the regulator in-line

between the gas supply and unit oriented so that the

arrow stamped on the back is pointing in the diretcion of

gas ﬂ ow. The regulator female gas ports come with 3/8”

adapters that may be removed to plumb to 1/2” pipe. Use

pipe compound resistant to all gasses on all male pipe

ﬁ ttings. Check that the regulator is conﬁ gured for your gas

supply as shown below.

4. Using a

" socket, remove the oriﬁ ce from

the valve. Access this through the hole in the

forward ﬁ rebox plate (see PARTS LIST and

Fig. 12-1). Check the number stamped on

the face of the oriﬁ ce (see Table 1). Repeat

for each burner as necessary.

5. If the barbecue does not have the proper oriﬁ ces

installed for the gas supply you intend to use,

replace them with the correct oriﬁ ces. Some

oriﬁ ces were supplied with the barbecue. They

may also be obtained from the conversion kit

or supplied by your local dealer.

Note: A regulator hose will need to be connected

for conversion to propane gas.

6. After checking the

orifice drill size

or replacing the

orifice, replace

the burner over

the oriﬁ ce ﬁ tting,

sliding it forward,

from behind the

forward ﬁ re wall, so the oriﬁ ce is centered

inside the burner gas inlet, and set it gently

onto the rear burner-support. The threaded

studs on the bottom back of the burner must

each ﬁ t through their respective holes in the

rear burner-support. This is critical to the safe

function of the barbecue. Finally, re-attach the

cotter pins from step 3 around the studs (see

Fig. 12-1).

MAIN BURNER AIR SHUTTER ADJUSTMENT

INSTALL THE VAPORIZER PANELS

Place the vaporizer panels directly on the support

bracket above the burners. The panels allow heat

from the burners to be evenly distributed throughout

the cooking area. The panels are stainless steel and

will heat and cool quickly, making your barbecue

very responsive to the changes you specify in

CHECKING/CONVERTING THE BURNER ORIFICES

MAIN BURNER ORIFICE SIZE CHECKING/

CONVERSION

Before beginning, make sure you have the proper

tools for the task.

This task requires:

• a #2 Phillips-head screwdriver

• a deep

" nut driver with a spacer (#6 nut)

Note: It may be necessary to remove the rotisserie

rod before beginning this procedure.

1. Remove cooking grids & vaporizer panels from the

barbecue.

2. Turn the burner valves to the OFF position.

Pull the valve knobs from their stems and

set them aside. Using a Phillips screwdriver,

unscrew the face fastener screws, (located

on the sides of the face) and remove the face

from the barbecue. Retain the screws and ﬁ nish

washers for reattaching the face.

Note: Carefully, lift the face away from the frame.

The spark generator for the ignition system

is attached to the inside of the face panel.

The spark generator knob need not be

detached, but the wires must be unplugged

from the generator before the face is

completely removed (see Fig. 12-2).

3. Remove the two cotter pins from underneath the

rear burner support and set them aside. Then

carefully lift the burner from the rear burner-

support and out from the hole in the forward ﬁ re

wall (see Fig. 12-1).

Fig. 12-3 - Burner oriﬁ ce diagram

Oriﬁ ce

Burner

Valve

Fig. 12-2

Spark generator

Removing/inserting main burner.

Hole with

oriﬁ ce

Burner

support

Cotter

pins

Fig. 12-1

Burner

support

grill temperature. They are rust resistant and may

be cleaned with standard oven cleaners. Some

discoloring will be seen with use. This is normal for

stainless steel and does not affect the function.

ADJUSTING YOUR BARBECUE

Important: This appliance may not light or heat

evenly or cook properly unless the

air shutters are adjusted following

installation (see AIR SHUTTER

ADJUSTMENT section).

Burner air shutters are easily accessed by removing

the front face panel. The air shutters are located on

the front portion of each burner and have a locking

screw that prevents the air shutter from inadvertent

movement (see Fig.

13-1).

To close or open the

air shutters, simply

loosen the locking

screw, using a long

stemmed Phillips

screwdriver, and

turn the air shutter

to open or close it.

Tighten the screws down when the desired setting

is achieved.

AIR SHUTTER ADJUSTMENT

Light the burner to be adjusted in accordance with

the LIGHTING INSTRUCTIONS and burn for 2

minutes with the burner control knob set to HIGH

and the oven open. After burning for 2 minutes,

open the air shutter until the ﬂ ames lift off, or appear

not to be touching the burner. Then begin closing

the air shutter until the ﬂ ames appear to burn while

CHECKING/CONVERTING THE BURNER ORIFICES (Cont.)

touching the burner ports (Fig. 13-2). You may then

see short yellow tips on the ﬂ ames. If ﬂ ames are a

lazy yellow, open the air shutters until the ﬂ ame is

blue with yellow tipping.

Note: Barbecues in some installations achieve a

better air/gas mixture and will ignite more

quickly if the valve is ﬁ rst turned beyond

HIGH to MEDIUM or LOW for lighting.

BACKBURNER ORIFICE SIZE CHECKING/

CONVERSION (IF EQUIPPED)

Before beginning, make sure you have the proper

tools for the task.

This task requires:

• a

nutdriver

• a

wrench or socket screwdriver

Note: It may be necessary to remove the

rotisserie rod before beginning this

procedure.

1. Remove the backburner assembly as follows:

a. Remove the backburner electrode mounting

screw (

" hex) (see Fig. 13-3) and loosen

the electrode. Draw the wire attached to

the electrode down through the slot in the

bottom of the bracket so that the left side of

the backburner is free to be removed.

b. Remove the backburner mounting screws

(

" hex) located at the left end of the

backburner assembly (see Fig. 13-3).

Remove electrode and backburner mounting screws.

Fig. 13-3

Mounting screws

Electrode

Ignitor

screw

Fig. 13-1

Locking

screw

Air shutter

Fig. 13-2 - Flame appearance diagram

Flame off ports

Flame on ports

c. Carefully pull the left end of the backburner

forward until the burner can be moved to the

left pulling it free from the oriﬁ ce located on

the right side (see Fig.

14-1).

d. Using a

" socket, remove the oriﬁ ce from the

oriﬁ ce holder and check the number stamped

on the face.

2. If an oriﬁ ce change is necessary, replace the

oriﬁ ce with the correctly sized one.

3. Replace the backburner assembly and the

electrode by reversing the procedure in steps

a. through c..

CHECKING/CONVERTING THE BURNER ORIFICES (Cont.)

The backburner oriﬁ ce can be seen on the

right side after removing the backburner.

Backburner

Oriﬁ ce

Fig. 14-1

Each time you use the barbecue, make sure that:

1. The area around the barbecue is clear of ﬂ ammable

vapors, liquids, and substances such as gasoline,

yard debris, wood, etc.

2. There is no blockage of the airﬂ ow through the vent

space located below the face of the unit.

3. When using propane gas:

a. The special ventilation openings in the enclosure

should be kept free and clear of debris

(see PLANNING THE LOCATION OF THE

BARBECUE).

b. If connected to a propane cylinder, the rubber

hose attached to the regulator should be carefully

inspected before each use.

c. The propane cylinder, regulator, and rubber hose should

be installed in a location not subject to heating above

125° F (51° C).

4. The burner ﬂ ames burn evenly along both sides of

each burner with a steady ﬂ ame, which is mostly

blue with yellow tipping. (Refer to section on AIR

SHUTTER ADJUSTMENT.) If burner ﬂ ames are not

normal, check the oriﬁ ce and burner for insects or

insect nests.

5. The inline gas valve or gas cylinder valve is always

shut OFF when the barbecue is not in use.

6. The drip collector hole is clear and unobstructed.

Excessive grease deposits can result in a grease

ﬁ re.

7. The barbecue is free and clear from combustible

materials, gasoline, and other ﬂ ammable vapors

and liquids.

BARBECUE SAFETY INFORMATION & MAINTENANCE

WARNING

NEVER cover the entire cooking or grill surface with griddles or pans. Overheating will occur and

burners will not perform properly when combustion heat is trapped below the cooking surface.

CAUTION: NEVER spray water on a hot gas unit.

DRIP COLLECTION SYSTEM

The drip collector in this barbecue is part of the unit’s

main frame and is located below the burners. The drip

collector has one hole that will allow excess drippings to

fall through during cooking, while separating the ﬁ rebox

from the drip tray. Clean the drip tray after each use.

The drip collector allows you to brush or scrape residue

from the barbecue’s inner liner into the drip tray.

Following the manufacturers instructions and regular

cleaning of the barbecue’s interior with oven cleaner,

will help to prevent grease ﬁ res.

Periodically check the burners to make sure they

are clear of debris. Properly adjusted burner ﬂ ames

burn evenly along both sides of each burner with

a steady ﬂ ame (mostly blue with yellow tipping). If

burner ﬂ ames are not normal, check the oriﬁ ce and

burner for insects or insect nests. (See section on

CHECKING/CONVERTING THE BURNER ORIFICES

for instructions on burner removal and replacement.)

Check the burner ports at least annually for blockage by

removing the burner (see oriﬁ ce changing instructions)

and visually inspect the gas intake tube for insects

and nests. A clogged tube can lead to a ﬁ re beneath

the grill.

8. Do not operate the backburner with its cover

installed.

ÉCLAIRAGE ÉLECTRONIQUE

1. Ouvrez tous les couvercles et enlevez toutes les couvertures

des brûleurs que vous souhaitez vous allumer.

2. Arrêtez tous les boutons de commande de gaz à leurs

positions.

3. Allumez le gaz à sa source.

Note: Aucune matière que la méthode d’éclairage

vous emploient,

n’allument pas

le gaz à plus

d’un brûleur à la

fois. Les brûleurs

adjacents de

barbecue croix-

mettront à feu

et l’écoulement

de gaz peut être

restreint.

ATTENTION: Si les brûleurs ne s’allument pas dans 5

secondes, enfoncez le bouton de commande

et tournez le bouton à AU LOIN. ATTENDEZ

5 MINUTES avant de répéter l’étape 5. Si

vous sentez le gaz suivez les instructions

sur la couverture de ce manuel. Si les

brûleurs ne s’allument toujours pas après

que plusieurs tentatives, se rapportent aux

instructions pour l’ÉCLAIRAGE MANUEL.

4. Enfoncez le bouton de commande pour que le brûleur

soit allumé et tournez-le dans la position LÉGÈRE de

HI, puis appuyez sur le bouton d’allumage. Une fois que

le brûleur s’allume, libérez le bouton d’allumage.

5. Répétez l’étape 4 pour que chaque brûleur additionnel soit

s’est allumé.

POUR LE PROPANE SEULEMENT

Les réservoirs de propane sont équipés d’un dispositif

d’arrêt de sûreté qui peut ne pas causer le bas ou aucun gaz

pressure/ﬂ ame aux brûleurs si le fonctionnement et allumer

des instructions ne sont pas suivis exactement (voir la note

importante dans la section de dépannage pour plus de détails.)

Note: Les barbecues dans quelques installations réalisent

un meilleur mélange d’air/gas et mettront à feu plus

rapidement si le bouton de commande de brûleur

est d’abord tourné au delà de la LUMIÈRE de HI

au BAS pour l’éclairage.

ÉCLAIRAGE MANUEL

ATTENTION: Attendez toujours 5 minutes le gaz à l’espace

libre après que n’importe quelle tentative non

réussie d’éclairage.

1. Suivez les étapes 1 à 4 (à gauche).

2. Insérez un allumeur brûlant de butane de long-baril, une

allumette brûlante de long-tige, ou une allumette brûlante

tenue par un support de prolongation de ﬁ l (Fig. 16-2)

par les grilles à cuire au brûleur (Fig. 16-3). Pour des

backburners, tenez la ﬂ amme contre le matériel perforé

du brûleur arrière. Pour des sideburners, tenez la ﬂ amme

contre le brûleur.

3. Tout en tenant l’allumette ou la ﬂ amme plus légère à côté

du brûleur, enfoncez le bouton de commande approprié

de brûleur et tournez-le dans le sens contraire des

aiguilles d’une montre dans la position LÉGÈRE de HI.

Quand les lumières de brûleur, enlèvent l’allumeur ou

s’assortissent.

4. Si le brûleur ne s’allume pas, enfoncez immédiatement

le bouton et tournez le bouton de commande de brûleur

à AU LOIN. ATTENDEZ 5 MINUTES avant de répéter

les étapes 2 à 4 des INSTRUCTIONS MANUELLES

d’ÉCLAIRAGE.

COUPER LE GRIL

Pour couper le gril, enfoncez chaque bouton de commande

de valve et tournez-le dans le sens des aiguilles d’une montre

à la position de repos.

Fermez toujours la valve à l’offre de gaz après chaque

utilisation du barbecue.

RAPPELEZ-VOUS: POUR L’ÉCLAIRAGE MANUEL SÛR, PLACEZ

Un ALLUMEUR BRÛLANT D’ALLUMETTE OU De BUTANE PRÈS

Du BRÛLEUR - ALLUMEZ ALORS Le GAZ

(voyez Fig. 16-3).

Fig. 16-2 - Support d’allumette

Lisez l’instruction entière avant que s’allumant et suivez ces instructions chaque fois vous lumière le barbecue.

ALLUMER DES INSTRUCTIONS (D’ALLUMAGE)

Fig. 16-3 - Éclairage manuel

Fig. 16-1 - Valve control knob

OFF

LIGHT

LOW

TURN OFF

TO TURN ON

Read setting

here

HIGH to

LIGHT

Read setting

here

TO TURN OFF

TO TURN ON

High to

light

MANUAL LIGHTING

CAUTION: Always wait ﬁ ve minutes for gas to clear

after any unsuccessful lighting attempt.

1. Follow steps 1 through 4 (left).

2. Insert either a burning long-barrel butane lighter,

a burning long-stem match, or a burning match

held by a wire extension holder (Fig.

17-2) through

the cooking grids to the burner (Fig. 17-3).

For backburners, hold the flame against the

perforated material of the backburner.

For sideburners, hold the ﬂ ame against the burner.

3. While holding the match or lighter ﬂ ame next to the

burner, depress the appropriate burner control knob

and turn it counterclockwise to the HI LIGHT position.

When the burner lights, remove the lighter or match.

4. If the burner does not light, IMMEDIATELY depress the

knob and turn the burner control knob to OFF. WAIT

FIVE MINUTES before repeating steps 2 through 4

of the MANUAL LIGHTING INSTRUCTIONS.

Note: Some installations achieve a better air/gas

mixture and may ignite quicker if the burner

control knob is ﬁ rst turned beyond HI LIGHT

to LOW for lighting.

ELECTRONIC LIGHTING

1. Open all lids and remove all covers from the burners

you wish to light.

2. Turn all gas control knobs to their OFF positions.

3. Turn on the gas at its source.

Note: No matter which lighting method you use,

DO NOT turn

on the gas to

more than one

burner at a time.

Adjacent grill

burners will

cross-ignite,

and gas

flow may be

restricted.

CAUTION: If the burners do not light within five

seconds, depress the control knob

and turn the knob to OFF. WAIT FIVE

MINUTES before repeating step 4. If you

smell gas, follow the instructions on the

cover of this manual. If the burners still do

not light after several attempts, refer to the

instructions for MANUAL LIGHTING.

4. Depress the control knob for the burner to be lit

and turn it to the HI LIGHT position, then press the

ignition button. Once the burner lights, release the

ignition button.

5. Repeat step 4 for each additional burner to be lit.

FOR PROPANE ONLY

Propane tanks are equipped with a safety shutdown

device that may cause low or no gas pressure/ﬂ ame

at the burners if operating and lighting instructions

are not followed exactly (See important note in the

TROUBLESHOOTING section for more details.)

REMEMBER: FOR SAFE MANUAL LIGHTING, PLACE A

BURNING MATCH OR BUTANE LIGHTER BESIDE THE

BURNER - THEN TURN ON THE GAS (see Fig. 17-3).

Fig. 17-2 - Match holder

Read entire instructions before lighting, and follow these instructions each time you light the grill.

LIGHTING (IGNITION) INSTRUCTIONS

Fig. 17-3 - Manual lighting

Fig. 17-1 - Valve control knob

OFF

LIGHT

LOW

TURN OFF

TO TURN ON

Read setting

here

HIGH to

LIGHT

Read setting

here

TO TURN OFF

TO TURN ON

High to

light

SHUTTING OFF THE GRILL

To shut off the grill, push in each valve control knob and

turn it clockwise to the OFF position.

Always close the valve to the gas supply after each use

of the grill.

ROTISSERIE INSTRUCTIONS (IF EQUIPPED)

USING THE BACKBURNER AND ROTISSERIE

Rotisserie cooking with the backburner is

accomplished without use of the main burners. Follow

the steps in the appropriate sections below to set up

and use these accessories.

SET UP

1. Remove the cooking grids from the barbecue,

if necessary, to obtain maximum clearance for

larger cuts. The ﬂ avor grids may also be removed

if required.

Tip: Aluminum foil or a baking pan may be

placed over the main burners, a little

forward of center, to catch excess drippings

from the meat.

2. Attach the rotisserie motor to the rotisserie

mounting on the right side of your barbecue by

sliding the bracket attached to the motor housing

onto the tab on the right of the barbecue so that

the spit rod will ﬁ t into the motor drive socket from

the left.

3. Follow the LIGHTING INSTRUCTIONS to light

the backburner.

4. Allow the backburner to preheat for approximately

10 minutes on HI LIGHT setting.

PUTTING THE MEAT ON THE SPIT ROD

1. Slide the meat and spit prongs onto the spit rod

so the meat is centered and balanced as well

as possible.

2. Tighten the spit prongs into place so that the

meat remains in a ﬁ xed position on the rod and

the meat rotates with the rod.

RUNNING THE ROTISSERIE

1. Place the pointed end of the spit rod into the motor

drive socket and rest the handle end of the spit

rod in the spit bracket on the right side of the

barbecue.

2. Plug in (if necessary) and turn on the rotisserie

motor.

3. Use a standard roasting guide to estimate the

length of time for your meat. A meat thermometer

may also be used to tell when your favorite cuts are

cooked to your liking. When testing temperatures

with a thermometer, turn off the rotisserie motor

and turn the backburner on LOW. This will keep

the meat from over cooking on one side.

Note: When burning properly, the backburner

grating will glow red. The ﬁ rst time it is used

the backburner may smoke a little.

Important: Operate the backburner with the oven

closed. This simulates an oven effect

and helps your meat cook faster.

Constant rotation of the spit assures

even cooking and maximum retention

of juices.

Note: On large cuts of meat or whole turkeys, it

may be necessary to reduce the heat from

your backburner. Cooking food at a lower

temperature for a longer period of time will

keep the outer surface from burning while

cooking the interior of the meat.

Spit rod

Knob

Spit prongs

Stainless

steel motor

PROBLEM POSSIBLE CAUSE CORRECTION

Ignition system

failure

1) Improper air shutter adjustment 1) Adjust air shutters.

2) Ignition wire disconnected 2) Replug wires into generator.

3) Low gas pressure 3) Adjust or replace battery.

4) Dead battery 4) Replace battery.

Insufﬁ cient heat

5) Improper air shutter adjustment 5) Adjust air shutters.

6) Using propane oriﬁ ce for natural gas 6) Change oriﬁ ces.

7) Low gas pressure/ﬂ ame (natural) 7) Have gas company check the

operating pressure at the unit.

8) Low gas pressure/flame

(propane)

8) Refill propane tank, or reset

propane tank safety*: Shut off all

valves (including propane tank) and

follow lighting instructions exactly.

Uneven heating

9) Burner ports partially blocked by debris 9) Remove burners and clean out ports.

10) Small spiders or insects in burner 10) Inspect burners for spider webs or

other debris that may block gas ﬂ ow.

Burner goes out on

LOW

11) Val ve “Low” setting needs

adjustment

11) Light burner on HIGH, immediately

turn to LOW setting. Remove

knob from valve and using a small

flat screwdriver, slowly turn the

adjustment screw in the stem,

a little at a time (30° to 45°), in

either direction, until the ﬂ ame is

approximately

” in height from

burner ports.

Rotisserie noisy

12) Rotisserie out of balance 12) Adjust counterbalance.

If you have trouble with the unit, please use this list to identify the problem. By trying one or more of the

solutions to the possible cause, you should be able to solve the problem. If this list does not cover your

present problem, or if you have other technical difﬁ culties with the unit, please contact your local dealer.

TROUBLESHOOTING

Note: *Propane tanks are equipped with a safety shutdown device that may cause low or no gas/ﬂ ame at the

burners if operating and lighting instructions are not followed exactly. If you suspect the propane tank safety

shutoff is in effect, shut off all burner control valves and the propane tank valve. Then read and follow

the LIGHTING INSTRUCTIONS exactly. Lighting instructions are located in the owner’s manual. If the

problem persists, continue troubleshooting, or contact your local dealer or distributor for assistance.

12) Adjust the meat on the spit rod.

REPLACING THE IGNITOR BATTERY

1. Remove the ignitor cover by turning it counterclockwise.

Important: Do not

attempt to pull or

turn the rubber cap.

2. Remove battery for

replacement. The battery

is reinstalled with the

negative (-) end out.

3. After properly inserting the

battery, replace the ignitor cover

by turning the cap clockwise.

WRONG!!

Note: If you have accidentally removed the rubber cap,

follow the instructions below to replace it.

3. Turn the cap

over and slide the

inner plastic sleeve

into the cap.

2. Carefully insert

the rubber cap into

the ignitor cover so

it sits behind inner

lip.

1. Pull the rubber

cap and the inner

plastic sleeve

apart.

THE COOKING GRID LIFTER

Hold the grid lifter by gripping the center section with the

prongs pointing down (use an oven mitt or heavy glove

if the grill is hot). Insert the notched end of the grid lifter

into the cooking grid, in front of the midway point (front to

back; Fig. 20-3), and central (left to right; Fig. 20-4).

Twist the grill lifter (clockwise or counterclockwise) so

the handle is parallel to the grill rods. This “seats” the

spiked end of the grid lifter between two rods, enabling

you to safely lift out the grid. Lift slowly and adjust the

grid lifter, if necessary, for balance.

Placement of the grid lifter in cooking grid

Fig. 20-3

Fig. 20-4

THE DRIP PAN

The drip collection system allows you to brush or scrape

excess dried residue from the grilling area directly into

the drip pan (see PARTS LIST for drip pan location).

To simplify cleanup when using the rotisserie, you may

place a baking pan or foil under the rotisserie on top of

the burners to collect the drippings. Clean the drip pan

after each use.

THE GRILL BRUSH (OPTIONAL)

Purchase a Fire Magic

stainless-steel grill brush (sold

separately) to keep your grill cleaner. It comes with

scraper for large particles and a replaceable head with

brass bristles for overall cleaning.

Grill brush with replacement head

Fig. 20-1

THE WARMING RACK (if equipped)

The warming rack (Fig. 20-2) is packed separately.

To install the warming rack, lift the front of the rack

up slightly and insert the rack hangers into the two

holes in the back of the inner oven hood just above the

backburner. Then lower the front of the rack into a level

position to lock the rack in place.

To remove the warming rack, lift up on the front of the

rack until the rack hangers pull free from their supporting

holes.

Note: Removing the warming rack before using the

rotisserie will leave more clearance for the

meat being cooked.

Fig. 20-2 Warming rack in place inside oven

THE VAPORIZER PANEL(S)

Place each vaporizer panel directly on a burner or burner

pair. Center each panel over the burner, oriented as

shown in Fig. 20-1.

Note: This allows heat from the burners to be evenly

distributed throughout the cooking area. The

vaporizer panels heat and cool quickly, making

the grill very responsive to the changes in heat

from the burners.

Fig. 20-1

ACCESSORIES

La page charge ...

American Outdoor 30NB-00SP Le manuel du propriétaire

Marque: American Outdoor

Modèle: 30NB-00SP

Catégorie: Barbecues

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: American Outdoor 30NB-00SP Owner's manual

American Outdoor 30NB-00SP Le manuel du propriétaire

American Outdoor 30NB-00SP Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents