Baby Lock Accomplish Le manuel du propriétaire

1

Thank you for purchasing this machine. Before using this machine, carefully read the “IMPORTANT SAFETY INSTRUCTIONS”, and then study this manual for the

correct operation of the various functions.

In addition, after you have nished reading this manual, store it where it can quickly be accessed for future reference.

INTRODUCTION

IMPORTANT SAFETY INSTRUCTIONS

Please read these safety instructions before attempting to use the machine.

DANGER - To reduce the risk of electrical shock

Always unplug the machine from the electrical outlet immediately after using, when cleaning, making any user servicing adjustments mentioned in this manual, or if

1

you are leaving the machine unattended.

WARNING - To reduce the risk of burns, re, electrical shock, or personal injuries.

Always unplug the machine from the electrical outlet when making any adjustments mentioned in this instruction manual.

2

To unplug the machine, switch the machine to the symbol “O” position to turn it off, then grasp the plug and pull it out of the electrical outlet. Do not pull on the cord.•

Plug the machine directly into an electrical outlet. Do not use an extension cord.•

Always unplug your machine if there is a power failure.•

Electrical Hazards:

3

This machine should be connected to an AC power source within the range indicated on the rating label. Do not connect it to a DC power source or power •

transformer. If you are not sure what kind of power source you have, contact a qualified electrician.

This machine is approved for use in the country of purchase only.•

2

Never operate this machine if it has a damaged cord or plug, if it is not working properly, has been dropped or damaged, or water is spilled on the unit. Return 4

the machine to the nearest authorized Baby Lock retailer for examination, repair, electrical or mechanical adjustment.

While the machine is stored or in use if you notice anything unusual, such as an odor, heat, discoloration or deformation, stop using the machine immediately and •

unplug the power cord.

When transporting the machine, be sure to carry it by its handle. Lifting the machine by any other part may damage the machine or result in the machine falling, •

which could cause injuries.

When lifting the machine, be careful not to make any sudden or careless movements, which may cause a personal injury.•

Always keep your work area clear:

5

Never operate the machine with any air openings blocked. Keep ventilation openings of the machine and foot control free from the build up of lint, dust, and loose •

cloth.

Do not store objects on the foot controller. •

Never drop or insert foreign objects in any opening.•

Do not operate where aerosol (spray) products are being used or where oxygen is being administered. •

Do not use the machine near a heat source, such as a stove or iron; otherwise, the machine, power cord or garment being sewn may ignite, resulting in fire or an •

electric shock.

Do not place this machine on an unstable surface, such as an unsteady or slanted table, otherwise the machine may fall, resulting in injuries.•

Special care is required while sewing:

6

Always pay close attention to the needle. Do not use bent or damaged needles.•

Keep fingers away from all moving parts. Special care is required around the machine needle.•

Switch the machine to the symbol “O” position to turn it off when making any adjustments in the needle area.•

Do not use a damaged or incorrect needle plate, as it could cause the needle to break.•

Do not push or pull the fabric • while sewing, and follow the instructions carefully when free motion stitching so that you do not deflect the needle and cause it to

break.

3

This machine is not a toy:

7

Your close attention is necessary when the machine is used by or near children.•

The plastic bag that this machine was supplied in should be kept out of the reach of children or disposed of. Never allow children to play with the bag due to the •

danger of suffocation.

Do not use outdoors.•

For a longer service life:

8

When storing this machine, avoid direct sunlight and high humidity locations. Do not use or store the machine near a space heater, iron, halogen lamp, or other hot •

objects.

Use only neutral soaps or detergents to clean the case. Benzene, thinner, and scouring powders can damage the case and machine, and should never be used.•

Always consult the Instruction and Reference Guide when replacing or installing any assemblies, the presser feet, needle, or other parts to assure correct •

installation.

For repair or adjustment:

9

If the light unit is damaged, it must be replaced by an authorized Baby Lock retailer.•

In the event a malfunction occurs or adjustment is required, first follow the troubleshooting table in the back of the Instruction and Reference Guide to inspect and •

adjust the machine yourself. If the problem persists, please consult your local authorized Baby Lock retailer.

Use this machine only for its intended use as described in the manual.

Use accessories recommended by the manufacturer as contained in this manual.

The contents of this manual and speciﬁcations of this product are subject to change without notice.

For additional product information, visit our website at www.babylock.com

SAVE THESE INSTRUCTIONS

This machine is intended for household use.

4

FOR USERS IN COUNTRIES EXCEPT EUROPEAN COUNTRIES

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or

lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by

a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

FOR USERS IN EUROPEAN COUNTRIES

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the

appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user

maintenance shall not be made by children without supervision.

FOR USERS IN THE UK, EIRE, MALTA

AND CYPRUS ONLY

IMPORTANT

In the event of replacing the plug fuse, use a fuse approved by ASTA to BS 1362, i.e. carrying the • mark, rating as marked on plug.

Always replace the fuse cover. Never use plugs with the fuse cover omitted.•

If the available electrical outlet is not suitable for the plug supplied with this equipment, you should contact your authorized Baby Lock retailer to obtain the correct •

lead.

5

CONTENTS

INTRODUCTION ........................................................................... 1

IMPORTANT SAFETY INSTRUCTIONS ...................................... 1

Accessories ................................................................................. 6

Machine Features ........................................................................ 7

Before You Begin (1) .................................................................... 8

Power Cord and Foot Controller ................................8

Main Power Switch ....................................................8

Thread Tension Dial ...................................................8

Handwheel ................................................................8

Stitch Length Regulator .............................................8

Reverse Stitch Lever .................................................8

Presser Foot Lever ....................................................9

Knee Lifter .................................................................9

Presser Foot Pressure Adjustment Dial ....................9

Fabric Extension Table ..............................................9

Before You Begin (2) .................................................................. 10

Thread Cutter Button ...............................................10

Needle Stop Position Button....................................10

Feed Dog Adjustment Knob ....................................10

Changing Needles ..................................................................... 11

Changing the Needle ...............................................11

Changing the Feed Pin ............................................11

Threading (1) .............................................................................. 12

Bobbin Winding .......................................................12

Bobbin Installation ...................................................14

Threading (2) .............................................................................. 15

Upper Threading......................................................15

Using the Automatic Needle Threader ....................16

Using the Spool Net ................................................16

Stitch Samples and Needle Chart ............................................ 17

Stitch Samples ........................................................17

Thread Tension ........................................................17

Changing Presser Feet ............................................................. 18

Changing Presser Feet (Zipper Foot) ......................18

Presser Feet ............................................................18

Basic Sewing (1) ........................................................................ 19

Basic Sewing ...........................................................19

Pin Feeding (for hard-to-handle fabrics) ..................19

Basic Sewing (2) ........................................................................ 20

Rolled Hem Foot .....................................................20

Basic Sewing (3) ........................................................................ 21

Zipper Foot ..............................................................21

Invisible Zipper Foot ................................................22

1/4” Foot ..................................................................22

Free Motion Quilting Foot ........................................23

Walking Foot ............................................................23

Seam Guide ............................................................24

Caring for Your Machine ............................................................ 25

Cleaning the Machine ..............................................25

Lubrication Points ....................................................25

Trouble Shooting ....................................................................... 26

6

Accessories

No. Part Name Part Code

1 Soft Cover XA0917-054

2 Medium Screwdriver XC9541-051

3 Small Screwdriver X55468-051

4 Cleaning Brush X59476-051

5 Knee Lifter XA0830-051

6 Needles and Case

(ORGAN HLX5)

1 Size 9, 2 Size 11, 1 Size 14,

1 Size 16, 1 Ballpoint Needle

X80805-151

7 Feed Pin 138483-051

8 Feed Pin Changer XC1407-051

9 General Purpose Foot XA1425-001

10 Bobbin (5) 100376-051

11 Spool Cap XA2111-050

12 Rolled Hem Foot X57138-101

13 Zipper Foot 112797-001

14 Invisible Zipper Foot XC0093-001

15 1/4” Foot XA7258-001

16 Free Motion Quilting Foot XA7255-301

17 Walking Foot XA7253-001

18 Seam Guide XA7256-001

19 Foot Controller XC8816-051

20 Fabric Extension Table XC3117-051

21 Spool Net XA5523-050

22 Flex Reaction Foot

(on machine)

136021-001

23 Spool Cone Holder

(on machine)

XF2071-001

1 2 3 4 5

6 7 8 9 10

11 12 13 14 15

16 17 18 19 20

21 22 23

Note (For U.S.A. only)

Foot controller: Model T•

This foot controller is used for sewing machine model BL520B.•

7

Machine Features

Presser Foot Pressure

Adjustment Dial (Page 9)

Three Holed

Thread Guide (Page 15)

Thread Trimmer

Feed Dog

(Page 10 and 19)

Thread Guide Bar

(Page 12)

Stitch Length

Regulator (Page 8)

Needle Stop Position

Button (Page 10)

Reverse Stitch

Lever (Page 8)

Feed Dog Adjustment

Knob (Page 10)

Knee Lifter

(Page 9)

Bobbin Winder

(Page 12)

Handwheel

(Page 8)

Main Power Switch

(Page 8)

Foot Controller Jack

(Page 8)

Power Supply

Jack (Page 8)

Spool Cone Holder

(Page 12)

Spool Pin

(Page 12)

Presser Foot

Lever (Page 9)

Bobbin Winding Thread

Guide (Page 12)

Handle

Air Vents

Thread Cutter

Button (Page 10)

Thread Tension Dial

(Page 8 and 17)

Indicator Lamp

Automatic Needle

Threader (Page 16)

Quick Bobbin

Thread Device (Page 14)

Thread Take-up Lever

(Page 15)

8

Before You Begin (1)

Power Cord

Foot Controller

Power Switch

I

O

Handwheel

1

2

3

4

5

6

7

Stitch Length Regulator

Reference Mark

Lower number

= shorter stitches

Higher number

= longer stitches

Stitch Length

Reverse Stitch

Lever

Upper Thread Tension

Loosen Tighten

Tension Block

Thread Tension Dial

When tighter thread tension is ●

desired, turn the tension dial

to the right. Upper and bobbin

threads will meet on right side of

the fabric.

When looser thread tension is

●

desired, turn tension dial to the

left. Upper and lower threads

will then meet on wrong side of

fabric.

Main Power Switch

Press power switch toward the ●

"I" position to turn machine on.

To turn the machine off, press ●

the power switch toward the "O"

position.

Handwheel

Position needle using ●

handwheel.

Always turn handwheel towards ✽

you.

CAUTION

Be sure to keep the area under

and around the needle clear.

Stitch Length Regulator

Adjust desired stitch length ●

using stitch regulator dial.

Reverse Stitch Lever

Sewing in reverse is possible ●

when the reverse stitch lever is

in the lowered position.

Make sure to continuously press ✽

the lever to its lowest position

when reverse sewing is desired.

When the stitch regulator dial is

✽

set between 5-7 mm, the reverse

stitch length is always 5 mm.

Power Cord and Foot Controller

WARNING

Please use common household

current.

Attach power cord. ●

Insert foot controller jack into machine.

●

When you press the foot controller

●

down lightly, the machine will run at

a low speed. When more pressure

is applied to foot controller, the

machine’s speed will increase. When

you remove your foot from the foot

controller, the machine will stop.

Slower

Faster

9

Presser Foot Lever

Lowering the presser foot lever ●

lowers the sewing foot down

onto the fabric and engages the

thread tension function.

When working with heavy ✽

fabrics or other fabrics that don’t

slide easily under the foot, raise

the presser foot lever to position

the fabric.

Knee Lifter

Using the convenient knee lifter ●

to lift and lower the presser

foot easily, leaving both of your

hands free.

Presser Foot Pressure

Adjustment Dial

Turning the pressure adjustment ●

dial raises and lowers the

pressure indicator needle as

the amount of pressure on the

presser foot changes.

See also: “Feed Dog Adjustment

Knob” on page 10.

See “Thread Tension” on page ✽

17.

Coordinate the color coding for ✽

proper foot pressure and feed

dog settings.

Presser Foot

Lever

Knee Lifter

Setting up the knee lifter.

Presser Foot Pressure Adjustment Dial

Pressure Indicator

Needle

Push the knee lifter bar all the ✽

way into the socket.

When knee lifter is not in use, ✽

it can be stored beneath the

fabric extension table.

Fabric Extension Table

Knee Lifter

Fabric Extension Table

Lower the adjustable table feet and slide the fabric extension table on to the

●

machine.

Table legs

1

3

2

Stopper

Hook

3

Guide pin

Hole

2

10

Before You Begin (2)

Thread Cutter Button

CAUTION

When the machine stops due to

jammed threads and so forth, do

not press on the foot controller;

turn power off, and move the

needle with the handwheel to

check the situation. Otherwise

broken needles could result.

The thread cutter trims upper and

●

bobbin threads at the end of seams.

Needle Stop Position Button

When indicator lamp is lit up, the

●

machine will stop sewing with the

needle lowered through the fabric.

When indicator lamp is off, the ●

needle position when sewing

stops, will be random.

If the safety mechanism is activated,

●

for example if the thread becomes

tangled, the red lamp ﬂashes.

Feed Dog Adjustment Knob

Height of feed dog can be ●

adjusted to coincide with fabric

weights.

Foot Pressure and Feed Dog Position

Thread Cutter Button

Indicator Lamp

Needle Stop Position Button

Feed Dog Adjustment Knob

Select one of four feed dog positions according to your needs.

Note

If a setting other than • is selected, the pin feed mechanism will not

operate.

Coordinate the color coding for proper foot pressure and feed dog settings.•

(Feed Dog Down)

(Pin Feeding)

Velvet

Lightweight Fabrics

Mediumweight Fabrics

Heavyweight Fabrics

Press with the presser lever down. ✽

11

Changing Needles

Changing the Needle

Turn the sewing machine off. 1

Raise needle to highest position

using handwheel, and lower

presser foot.

Loosen screw with screwdriver, 2

and remove needle.

Hold the needle with the flat 3

side to the right, and insert the

needle as far as it will go. Make

sure needle is securely set in

the needle chamber by screwing

in tightly.

If the needle is not adequately ✽

inserted or the screw is loose,

this may break the needle or

cause a breakdown and the

needle threader will not work.

Check needles on a ﬂat surface ✽

to make sure they are not bent.

Changing the Feed Pin

Set the feed dog to the “velvet” 1

position. (See page 10.)

Remove needle, presser foot 2

and needle plate.

Lower presser foot and turn 3

handwheel until feed pin is in its

highest position.

Insert small screwdriver 4

(included) as shown in diagram.

Note

HLX5 needles should be used; however, Schmetz 130/705H may also be •

used under normal circumstances.

Screwdriver

Flat surface

Lay needle on

a flat surface

(such as the needle

plate or a plate

of glass).

The needle should lay

parallel to a surface.

While holding spring with 5

fingertip, lower the feed pin

changer onto the needle to pick

it up.

Attach new feed pin to feed pin 6

changer, lower and attach while

holding spring with fingertip.

Remove screwdriver.7

Re-attach needle plate, needle 8

and presser foot.

CAUTION

Please make sure the power to the machine is turned off before carrying out the

following operations. There is a chance of injury if the machine accidentally starts

running during this operation.

12

b

c

d

a

c

a

b

Spool of Thread

�2

Spool Cone Holder

Spool Cap

�1

Threading (1)

CAUTION

Do not move bobbin winding clutch while

machine is running.

Bobbin Winding

Raise the thread guide bar all the way.1

Mount a spool of thread on the spool pin.2

✽1 Use spool cap when using parallel-wound thread.

✽2 Use spool cone holder to stabilize cone shaped spools of thread.

Pass the thread through the 3

triangular hole.

Pass thread through bobbin winding 4

thread guide as shown in drawing.

Run thread through top 5

thread notch 1, and turning

the bobbin align bottom

thread notch 2 of the bobbin

with guide pin on bobbin

winder shaft.

Press bobbin winding clutch up against 6

empty bobbin. If the bobbin stop does not

slide easily between the top and bottom of

the bobbin, check that the bobbin is seated

properly with the guide pin (5) inserted into

the lower notch.

Bobbin

Bobbin Winder

Shaft

Guide Pin

Thread Notch 1

Thread Notch 2

Bobbin Winding Clutch

5 - A: See the following illustrations.

13

Stop winding process when bobbin 9

is full. Remove your foot from the

foot controller.

Manually move bobbin winding 0

clutch back to original position.

While holding the end of the thread, 7

press on the foot controller for a

few seconds. Once enough thread

has wound itself around the bobbin

to hold itself in place, release the

foot controller and trim the excess

thread.

Cut thread and remove bobbin.A

Start winding the bobbin again by 8

pressing down on the foot controller.

�

Place the thread end so that it does

not protrude from the bobbin.

Bobbin Winding Clutch

Controller

Pedal

Press down

�

Pressing down on the controller

harder increases the winding speed.

14

Quick Bobbin

Thread Device

Lift needle plate and open 1

bobbin door.

Place bobbin inside the bobbin case.2

Run thread through thread notch and ✽

under latch spring, so that a length of

thread is exposed.

Always use the bobbin case that was ✽

supplied with this machine. A secondary

bobbin case can be ordered from your

Baby Lock retailer.

Pull the latch lever of the bobbin 3

case out and push the bobbin case

into the shuttle race and release the

latch lever.

If the latch lever on the bobbin case is not

✽

set securely on the hook, it may ﬂy off during

sewing and cause lower thread breakage.

Rotate the handwheel one full rotation

towards you to check that the bobbin case is

set securely.

Pass the thread through the quick 4

bobbin thread device in the order

numbered 1 2, pull in the direction

of the arrow 3, then cut the thread.

★

Quick Bobbin Thread Device

This device cuts the bobbin thread

end to an appropriate length after the

bobbin has been replaced and holds it

at that length. Following this process

eliminates the need to manually pull the

bobbin thread through the hole in the

needle plate. Simply close the bobbin

case and continue the upper threading

process.

Bobbin Installation

� Bobbin should be

positioned so it

winds to the left.

Latch Spring

Thread Notch

10 cm (4 inches)

2

1

2

1

Bobbin Door

Needle Plate

1

2

3

Lower slide plate and close 5

bobbin door, following numbers

1 2 above in order.

Bobbin Thread Setting Cover

When the fabric extension table is set in place ●

Open the bobbin thread setting cover

beforehand, then following the above

directions set the bobbin thread in

place. (You can set the bobbin thread

in place without removing the fabric

extension table.)

CAUTION – Moving parts –

To reduce risk of injury, turn the power to the machine off before servicing. Open covers.

15

Threading (2)

1

2

6

7

8

9

0

A

3

4

5

Long

Groove

Scarf

(depression on

needle shaft)

Thread

Needle Hole

1

7

2

3

5

6

4

7

8

9

0

A

Make sure thread take-up lever

●

(

7

) is in highest position and

presser foot is up.

When using polyester thread or thread that

✽

tangles or breaks, run the thread through

all three holes of the thread guide.

If the thread still tangles or breaks,

✽

run the thread through the holes

backwards as shown in diagram.

CAUTION

Turn off the power to the machine before using the

automatic needle threader. Otherwise, it may cause

injuries if you unintentionally press down on the foot

controller.

Upper Threading

Thread tension may not be adjusted ✽

adequately unless the thread runs

correctly through the take-up spring.

Thread take-up spring

16

Before sewing, pull the thread loop to the

6

right and then pull the thread tail towards

the back of the machine following the

opening in the presser foot.

The automatic needle threader cannot be

●

used with the thread-needle combinations

illustrated in the chart shown above.

Transparent nylon thread can be used

regardless of the chart, providing the

needle used is a #14 or #16.

Rotate handwheel towards you until 1

needle is in the highest position,

and lower presser foot.

Take thread in your left hand, and 2

gently pull it forward.

Lower automatic needle threader.3

Pull thread along the right side of the pin.

✽

Do not force the needle threader lower

✽

than the eye of the needle. Be sure that

the needle is in the highest position.

Turn the needle threader lever all the

4

way in the direction of 1 and when

the hook extends from the needle

hole, pull the thread in the direction

of 2 to catch it on the hook.

While holding the thread gently, return

5

the needle threader lever to the right. As

you do this the hook that has caught the

thread will move as well, pulling a loop

of thread through the eye of the needle.

Using the Automatic Needle Threader

Thread

1

2

Hook

Automatic

Needle

Threader

Pull the thread to

✽

the left and check

that it is caught

on the hook.

Needle (HLX5) Thread

#9 #20 #30 #50 #60

#11 #20 #30

#14 #20 #30

#16 #20

Using the Spool Net

a

b

c

d

If using transparent nylon

thread, metallic thread, or

other strong thread, place

the included spool net over

the spool before using.

If the spool net is too long,

fold it once to match it to the

spool size before placing it

over the spool.

Spool net1

Thread spool2

Spool pin3

Spool cap4

17

Stitch Samples and Needle Chart

Stitch Samples

Set stitch length regulator to 1

desired stitch length.

Make sure approximately 15 2

cm (6 inches) of upper thread

is pulled under the presser

foot and toward the rear of the

machine. While needle is in

raised position, insert a test strip

from the garment fabric under

the foot.

Lower presser foot.3

Turn the handwheel toward you 4

to lower the needle through the

fabric, then press gently on the

foot controller to begin.

Turn the handwheel toward you

5

to raise the needle and thread

take-up lever to their highest

positions.

Raise the presser foot, remove 6

fabric and then manually cut the

thread with the cutter on the left

side of the head of the machine

or with a pair of scissors.

When using thread cutter: ✽

5

Press the thread cutter button

while the presser foot lever is in

the down position

.

6

Raise presser foot and remove

fabric.

Thread Tension

Bobbin thread should feed smoothly. Adjust bobbin thread ✽

to match that of upper thread. (If bobbin thread is too tight

it may cause fabric to bunch up.)

to increase

bobbin

tension

to reduce

needle

thread

tension

to increase

needle

thread

tension

Fabric

Upper

Thread

Lower

Thread

to reduce

bobbin

tension

Correct thread tension

Incorrect thread tension can lead

to such undesirable results as

messy stitches, puckered seams

and thread breakage.

Upper

Thread

Lower

Thread

Right side of Fabric

Upper

Thread

Lower

Thread

Right side of Fabric

Wrong side of fabric

Bobbin tension . . .

Proper

When it is week

Bobbin tension . . .

Proper

When it is strong

Wrong side of fabric

Adjust the upper thread to match the bobbin thread.

Selecting the proper needle for use with the fabric and thread you are working with

●

The following chart applies to many different fabric, thread and needle combinations. ✽

HLX5 needles are recommended; however, Schmetz 130/705H needles may also be used under normal ✽

sewing conditions.

Adjust the pressure adjustment dial and the feed dog adjustment knob according to the chart on the sewing ✽

machine.

When sewing on knit fabrics such as jersey or tricot, use a ballpoint needle or a needle designed for use with ✽

knit fabrics.

For best results when using metallic threads, sew with a good quality thread, set upper tension on 2, and ✽

use metallic needle.

Fabric - Thread - Needles

Cloth Thread Needle (HLX5)

Specialty

fabrics

Velvet Silk, Polyester #30 – #50 #11 – #14

Quilt Polyester #20 – #50 #11 – #16

Synthetic Suede Polyester #20 – #50

Knit Polyester #20 – #50

Coating Polyester #50 #11 – #14

Light

weight

fabrics

Lawn Cotton #80 #9

Tricot Polyester #60

Silk Georgette Silk #50

Wool Georgette Silk, Polyester #50 #11

Medium

weight

fabrics

Gingham Cotton #60 – #80 #11 – #14

Lightweight Jersey Polyester #60 #11

Gabardine, Flannel Silk #50

Heavy

weight

fabrics

Denim Cotton #20 – #50 #14 – #18

Jersey Polyester #20 – #50 #11 – #16

Tweed Silk #20 – #50

HLX5

Schmetz

130/705H

#9 #65

#11 #75

#14 #90

#16 #100

#18 #110

18

Changing Presser Feet

(Zipper Foot)

Raise presser foot, and raise 1

needle to highest position.

Loosen and remove screw using 2

screwdriver.

Changing Presser Feet

Presser Feet

Attach zipper foot and tighten 3

screw.

Use the same method to attach ✽

the other feet that come with

your machine.

See page 23 for directions on ✽

attaching the “Walking Foot”.

Use the position knob on back of ✽

the zipper foot to adjust position

of foot in relation to needle.

Only the zipper foot has a ✽

position knob. You can begin

sewing with all other presser feet

immediately after attaching.

Use only feet supplied with your machine. Each foot is

✽

specially designed for this machine and has clearance for

the pin at the rear of each foot. Use of other presser feet

may damage or break the pin feed mechanism.

CAUTION

Make sure the power to the machine is off before changing presser feet.

Walking Foot ●

For sewing or

quilting on fabrics

which stick or tend

to slip. Useful for

sewing multiple

layers as in quilting.

1/4” Foot ●

For quilt and

patchwork piecing

with 1/4” or 1/8”

seam allowance.

Zipper Foot ●

Use to attach fasteners

other than concealed

fasteners. The zipper

foot can also be used

to secure piping in

place as you sew. Use

the side of the foot

closest to the needle to

rest against the edge of

the piping as you sew.

General Purpose Foot

●

This foot is used for

most sewing. (Can

also be used for

sewing thick fabrics or

seams.)

When sewing thick

✽

seams, lightly guide

the fabric with your

hand on the downward

side of the seam.

Can also be used with

✽

pin feeding.

Flex Reaction ●

Foot

For perfect

stitching on

otherwise difﬁcult

fabrics like velvet,

leather and suede.

Rolled Hem Foot ●

Use on the edge

of fabric, such as

on hems of dress

shirts, to fold the

edge of the fabric

in three while

sewing.

Invisible Zipper Foot

●

Use to attach

concealed fasteners.

Free Motion ●

Quilting Foot

Spring action

foot for darning,

quilting or

free motion

embroidery.

La page charge ...

Baby Lock Accomplish Le manuel du propriétaire

Ce manuel convient également à

Baby Lock Accomplish Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents