FEIN MultiMaster Top Manuel utilisateur

Marque: FEIN

Modèle: MultiMaster Top

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Ce manuel convient également à

72295267090

USA

FEIN Power Tools, Inc.

1000 Omega Drive

Suite 1180

Pittsburgh, PA 15205

Phone: 800-441-9878

www.feinus.com

Canada

FEIN Canadian Power Tool

Company

323 Traders Boulevard East

Mississauga, Ontario L4Z 2E5

Telephone: (905) 8901390

Phone: 1-800-265-2581

www.fein.com

FEIN Service USA

FEIN Power Tools, Inc.

2735 Hickory Grove Road

Davenport, IA 52804

Phone: 800-441-9878

magdrillrepair@feinus.com

Headquarter

C. & E. FEIN GmbH

Hans-Fein-Straße 81

D-73529 Schwäbisch Gmünd-Bargau

www.fein.com

 FMM350QSL (**) 7 229 ...

✔

OBJ_DOKU-0000006219-003.fm Page 1 Tuesday, August 15, 2017 1:52 PM

Instruction Manual

Mode d’emploi

Instrucciones de uso

OBJ_BUCH-0000000240-003.book Page 2 Tuesday, August 15, 2017 1:54 PM

For your safety.

Read all safety warnings and

all instructions. Failure to fol-

low the warnings and instructions may result

in electric shock, fire and/or serious injury.

Save all warnings and instructions for future-

reference.

Do not use this power tool before you

have thoroughly read and completely

understood this Instruction Manual, including

the figures, specifications, safety regulations

and the signs indicating DANGER, WARN-

ING and CAUTION.

Only carry out such operations with this

power tool as intended for by FEIN. Only use

application tools and accessories that have

been released by FEIN.

Please also observe the relevant national

industrial safety regulations.

Non-observance of the safety instructions in

the said documentation can lead to an electric

shock, burns and/or severe injuries.

This Instruction Manual should be kept for

later use and enclosed with the power tool,

should it be passed on or sold.

SAVE THESE INSTRUCTIONS.

The term “power tool” in the warnings refers

to your mains-operated (corded) power tool

or battery operated (cordless) power tool.

General safety rules.

1) Work area safety

a)Keep work area clean and well lit. Clut-

tered or dark areas invite accidents.

b)Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power

tools create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders away

while operating a power tool. Distrac-

tion can cause you to lose control.

2) Electrical safety

a)Power tool plugs must match the outlet.

Never modify the plug in any way. Do not

use any adapter plugs with earthed

(grounded) power tools. Unmodified

plugs and matching outlets will reduce

risk of electric shock.

b)Avoid body contact with earthed or

grounded surfaces such as pipes, radia-

tors, ranges and refrigerators. There is

an increased risk of electric shock if

your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power

tool will increase the risk of electric

shock.

d)Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging

the power tool. Keep cord away from

heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase

the risk of electric shock.

e) When operating a power tool outdoors,

use an extension cord suitable for out-

door use. Use of a cord suitable for out-

door use reduces the risk of electric

shock.

f) If operating a power tool in a damp loca-

tion is unavoidable, use a ground fault

circuit interrupter (GFCI) protected sup-

ply. Use of an GFCI reduces the risk of

electric shock.

3) Personal safety

a)Stay alert, watch what you are doing

and use common sense when operating

a power tool. Do not use a power tool

while you are tired or under the influ-

ence of drugs, alcohol or medication. A

moment of inattention while operating

power tools may result in serious per-

sonal injury.

b)Use personal protective equipment.

Always wear eye protection. Protective

equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing pro-

tection used for appropriate conditions

will reduce personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the off-position before

connecting to power source and/or bat-

tery pack, picking up or carrying the

tool. Carrying power tools with your

finger on the switch or energising

power tools that have the switch on

invites accidents.

WARNING

OBJ_BUCH-0000000240-003.book Page 3 Tuesday, August 15, 2017 1:54 PM

d)Remove any adjusting key or wrench

before turning the power tool on. A

wrench or a key left attached to a rotat-

ing part of the power tool may result in

personal injury.

e) Do not overreach. Keep proper footing

and balance at all times. This enables

better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose cloth-

ing or jewelery. Keep your hair, clothing

and gloves away from moving parts.

Loose clothes, jewelry or long hair can

be caught in moving parts.

g)If devices are provided for the connec-

tion of dust extraction and collection

facilities, ensure these are connected

and properly used. Use of dust collec-

tion can reduce dust-related hazards.

4) Power tool use and care

a)Do not force the power tool. Use the cor-

rect power tool for your application. The

correct power tool will do the job bet-

ter and safer at the rate for which it was

designed.

b)Do not use the power tool if the switch

does not turn it on and off. Any power

tool that cannot be controlled with the

switch is dangerous and must be

repaired.

c) Disconnect the plug from the power

source and/or the battery pack from the

power tool before making any adjust-

ments, changing accessories, or storing

power tools. Such preventive safety

measures reduce the risk of starting the

power tool accidentally.

d)Store idle power tools out of the reach of

children and do not allow persons unfa-

miliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the hands

of untrained users.

e) Maintain power tools. Check for mis-

alignment or binding of moving parts,

breakage of parts and any other condi-

tion that may affect the power tool’s

operation. If damaged, have the power

tool repaired before use. Many accidents

are caused by poorly maintained power

tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with

sharp cutting edges are less likely to

bind and are easier to control.

g)Use the power tool, accessories and tool

bits etc. in accordance with these

instructions, taking into account the

working conditions and the work to be

performed. Use of the power tool for

operations different from those

intended could result in a hazardous sit-

uation.

5) Service

a)Have your power tool serviced by a qual-

ified repair person using only identical

replacement parts. This will ensure that

the safety of the power tool is main-

tained.

Special safety instructions.

Hold power tool by insulated gripping sur-

faces when performing an operation where

the cutting accessory may contact hidden

wiring or its own cord. Cutting accessory con-

tacting a “live” wire will make exposed metal

parts of the power tool “live” and shock the

operator.

Use clamps or another practical method to

secure and support the work piece on a stable

surface. When holding the work piece only

by hand or against your body, it remains in an

unstable position, which can lead to loss of

control.

Do not use accessories which are not specifi-

cally designed and recommended by the

power tool manufacturer. Safe operation is

not ensured merely because an accessory fits

your power tool.

OBJ_BUCH-0000000240-003.book Page 4 Tuesday, August 15, 2017 1:54 PM

Grasp/hold the power tool in such a safe man-

ner that your body never comes in contact

with the application tool, particularly when

working with application tools pointing

toward the gripping area, such as with saw

blades or cutting tools. Touching sharp cut-

ting edges or edges can lead to injury.

Wear personal protective equipment. Depend-

ing on application, use face shield, safety

goggles or safety glasses. Where appropriate,

wear dust mask, hearing protectors, gloves

and workshop apron capable of stopping

small abrasive or workpiece fragments. The

safety glasses must be capable of protecting

against flying particles generated by the vari-

ous operations. Prolonged exposure to high

intensity noise may cause loss of hearing.

Do not direct the power tool against yourself,

other persons or animals. Danger of injury

from sharp or hot application tools.

Do not rivet or screw any name-plates or

signs onto the power tool. If the insulation is

damaged, protection against an electric shock

will be ineffective. Adhesive labels are recom-

mended.

Clean the ventilation openings on the power

tool at regular intervals using non-metal

tools. The blower of the motor draws dust

into the housing. An excessive accumulation

of metallic dust can cause an electrical hazard.

Before putting into operation, check the

power connection and the power plug for

damage.

Recommendation: The tool should always be

supplied with power via a ground fault circuit

interrupter (GFCI) with a rated current of

30 mA or less.

Handling hazardous dusts.

When working with power

tools, such as when grinding,

sanding, polishing, sawing or for other work

procedures where material is removed, dusts

develop that are both hazardous to one’s

health and can spontaneously combust or be

explosive.

Contact with or inhaling some dust types can

trigger allergic reactions to the operator or

bystanders and/or lead to respiratory infec-

tions, cancer, birth defects or other reproduc-

tive harm.

Examples of such materials which contain

chemicals that can produce hazardous dusts,

are:

– Asbestos and materials containing asbes-

tos;

– Lead-containing coatings, some wood

types such as beech and oak;

– Minerals and metal;

– Silicate particles from bricks, concrete and

other materials containing stone;

– Solvent from solvent-containing paint/

varnish;

– Arsenic, chromium and other wood pre-

servatives;

– Materials for pesticide treatment on boat

and ship hulls;

– Stainless steel dust, metal dust and non-

ferrous metal dust;

To minimize the unwanted intake of these

materials:

– Use dust extraction matched appropriately

for the developing dust.

– Use personal protective equipment, such

as a P2 filter-class dust protection mask.

– Provide for good ventilation of the work-

place.

The risk from inhaling dusts depends on how

often these materials are worked. Materials

containing asbestos may only be worked on

by specialists.

Wood and light-metal dust can

cause spontaneous combus-

tion or explosions.

Hot mixtures of sanding dust and paint/var-

nish remainders or other chemical materials

in the filter bag or the vac filter can self-ignite

under unfavorable conditions, such as spark-

ing from sanding metal, continuous sunlight

or high ambient temperatures. To prevent

this:

– Avoid overheating the material being

sanded and the power tool.

– Empty the dust collector/container in time.

– Observe the material manufacturer’s

working instructions.

– Observe the relevant regulations in your

country for the materials being worked.

WARNING

CAUTION

OBJ_BUCH-0000000240-003.book Page 5 Tuesday, August 15, 2017 1:54 PM

Hand/arm vibrations.

While working with this power

tool, hand/arm vibrations

occur. These can lead to health impairments.

The vibration emission value

during actual use of the power

tool can differ from the declared value

depending on the ways in which the tool is

used.

It is necessary to identify safety

measures to protect the oper-

ator that are based on an estimation of expo-

sure in the actual conditions of use.

The vibration emission level given in this

information sheet has been measured in

accordance with a standardised test given in

EN 60745 and may be used to compare one

tool with another. It may be used for a pre-

liminary assessment of exposure.

The declared vibration emission level repre-

sents the main applications of the tool. How-

ever if the tool is used for different

applications, with different accessories or

poorly maintained, the vibration emission

may differ. This may significantly increase the

exposure level over the total working period.

An estimation of the level of exposure to

vibration should also take into account the

times when the tool is switched off or when

it is running but not actually doing the job.

This may significantly reduce the exposure

level over the total working period.

Identify additional safety measures to protect

the operator from the effects of vibration

such as: maintain the tool and the accessories,

keep the hands warm, organisation of work

patterns.

Emission values for sound and vibration (Two-figure – specifications as per ISO 4871)

WARNING

Sound emission FMM350QSL (**)

A-weighted emission pressure power level measured at the workplace

(re 20 μPa), in decibels 72

Measuring uncertainty

, in decibels 3

Measured A-weighted sound power level

(re 1 pW), in decibels 83

Measuring uncertainty

, in decibels 3

C-weighted peak sound pressure level measured at the workplace

pCpeak

, in decibels 84

Measuring uncertainty

pCpeak

, in decibels 3

REMARK: The sum of the measured emission value and respective measuring inaccuracy

represents the upper limit of the values that can occur during measuring.

Wear hearing protection!

Measured values determined in accordance with the corresponding product standard.

OBJ_BUCH-0000000240-003.book Page 6 Tuesday, August 15, 2017 1:54 PM

Extension cable.

If the use of an extension cord

is required, its length and con-

ductor cross-section must be adequate for the

application in order to prevent a voltage drop

in the extension cord, power loss and over-

heating of the power tool. Otherwise, the

extension cable and power tool are prone to

electrical danger, and the working efficiency is

decreased.

Recommended dimensions of extension cords

at an operating voltage of 120 V – single-

phase a. c., with only FMM350QSL (**) con-

nected:

Intended use of the power tool:

Hand-guided oscillator for sanding small sur-

faces, corners and edges, for sawing thin parts

of steel sheet, wood and plastic, for scraping,

polishing, rasping, cutting and separating with-

out water in weather-protected environ-

ments, using the application tools and

accessories recommended by FEIN.

Vibration

Classification of FEIN

application tools accord-

ing to vibration class

Weighted

acceleration*

VC0

< 2.5 m/s

< 8 ft/s

VC1

< 5 m/s

< 16 ft/s

VC2

< 7 m/s

< 23 ft/s

VC3

< 10 m/s

< 33 ft/s

* These values are based on a work cycle consist-

ing of no-load and full-load operation of the same

duration.

For information on the vibration class assigned to

the application tool, please refer to the enclosed

data sheet 3 41 30 443 06 0.

VC4

< 15 m/s

< 50 ft/s

VC5

< 30 m/s

< 100 ft/s

a 1.5 m/s

4.92 ft/s

Vibration

* These values are based on a work cycle consist-

ing of no-load and full-load operation of the same

duration.

For information on the vibration class assigned to

the application tool, please refer to the enclosed

data sheet 3 41 30 443 06 0.

WARNING

Max. cable length, ft Max. cable length, m

≤ 100 100

–200

200

–300

≤ 30 30

– 60

–100

Min. conductor size

A.W.G.

Min. conductorcross-

section, mm

16 14 12 1.5 2.5 4

OBJ_BUCH-0000000240-003.book Page 7 Tuesday, August 15, 2017 1:54 PM

Operation of the power tool off power

generators.

This power tool is also suitable for use

with AC generators with sufficient power

output that correspond to the Standard

ISO 8528, design type G2. This Standard is

particularly not complied with when the so-

called distortion factor exceeds 10 %. When

in doubt, please refer to the generator

instruction/specification guide.

Operating the power tool off

power generators whose no-

load speed exceeds the voltage value on the

type plate of the power tool is prohibited.

Symbols.

WARNING

Symbol, character Explanation

Observe the instructions in the text or graphic opposite!

General prohibition sign. This action is prohibited.

Make sure to read the enclosed documents such as the Instruction

Manual and the General Safety Instructions.

Do not touch the saw blade. Danger of sharp application tools moving

back and forth.

Warning against sharp edges of application tools, such as the cutting

edges of the cutter blades.

Before commencing this working step, pull the power plug out of the

socket. Otherwise there will be danger of injury if the power tool

should start unintentionally.

Use eye protection during operation.

Wear hearing protection while working.

Use a dust mask during operation.

Use protective gloves during operation.

Observe the notes in the text aside!

Switching on

Switching off

This symbol confirms the certification of this product for the USA and

Canada.

This sign warns of a directly imminent, dangerous situation. A false

reaction can cause a severe or fatal injury.

DANGER

OBJ_BUCH-0000000240-003.book Page 8 Tuesday, August 15, 2017 1:54 PM

This sign indicates a possible dangerous situation that could cause severe

or fatal injury.

This sign warns of a possible dangerous situation that could cause injury.

Worn out power tools and other electrotechnical and electrical prod-

ucts should be sorted separately for environmentally-friendly recycling.

Product with double or reinforced insulation

~ or a. c. Alternating current

1 ~ Alternating current, single-phase

Symbol, character Explanation

WARNING

CAUTION

Character Unit of measurement,

national

Explanation

rpm; /min; min

-1

; r/min Rated oscillation rate

W Electrical power

° Oscillation angle

U V Electric voltage

f Hz Frequency

A Electric current intensity

lbs Mass

l ft, in Length, width, height, depth, diameter or thread

Ø ft, in Diameter of a round part

K...

Uncertainty

m/s

Vibrational emission value according to EN 60745

(vector sum of three directions)

m, s, kg, A, mm, V, W,

Hz, N, °C, dB, min, m/s

Basic and derived units of measurement from the

international system of units SI.

OBJ_BUCH-0000000240-003.book Page 9 Tuesday, August 15, 2017 1:54 PM

Technical description and specifications.

Before mounting or replacing cutting tool or accessories, pull the power plug.

This preventive safety measure rules out the danger of injuries through acciden-

tal starting of the power tool.

Not all accessories described or shown in this instruction manual will be included with your-

power tool.

WARNING

Thumbwheel for pre-selection

of oscillating frequency

Clamping lever

Application tool

On/Off switch

Gripping surface

Fig. 1

Type FMM350QSL (**)

Order number 7 229 ...

Current consumption 3.6 A

Rated oscillation rate 10000 – 19500 /min

Amplitude 2 x 1.7°

Weight according to EPTA-Procedure 01 3.2 lbs (1.45 kg)

Class of protection /II

OBJ_BUCH-0000000240-003.book Page 10 Tuesday, August 15, 2017 1:54 PM

Assembly instructions.

Before mounting or replacing cutting tool or accessories, pull the power plug.

This preventive safety measure rules out the danger of injuries through acci-

dental starting of the power tool.

Mounting the depth stop (figure 2).

Mount the depth stop with the 2 screws to

the bottom side of the gear case.

WARNING

Fig. 2

Depth stop

Screws

OBJ_BUCH-0000000240-003.book Page 11 Tuesday, August 15, 2017 1:54 PM

Assembly instructions.

Before mounting or replacing cutting tool or accessories, pull the power plug.

This preventive safety measure rules out the danger of injuries through acci-

dental starting of the power tool.

For all work or when changing application tools, always wear protective gloves.

Danger of injury from the sharp edges of the application tools. Application

tools can become very hot while working. Danger of burns!

Changing the tool.

Do not switch the power tool

on while the clamping lever is

open. Otherwise there is danger of crushes or

contusions to the hand and fingers.

Do not actuate the clamping

lever while the power tool is

running. Otherwise there is danger of injury.

Do not reach into the area of

the clamping jaws. Otherwise

there is danger of crushes or contusions to

the fingers.

Do not operate the power tool

with open clamping jaws and

without an application tool! This could dam-

age the power tool.

When the clamping jaws are

open before the application

tool is inserted, pivot the clamping lever

toward the front and then back again. The

clamping jaws are closed now. The application

tool can be inserted.

Do not overload the power

tool. Overloading increases

the vibration on the power-tool housing and

can cause the power tool to become very hot.

Danger of injury.

Inserting the application tool (figure 3).

Clean the tool holder and the application tool.

In the starting position, the clamping jaws in

the tool holder are together. In this position,

the application tool can be clipped-in easily.

WARNING

CAUTION

Fig. 3

OBJ_BUCH-0000000240-003.book Page 12 Tuesday, August 15, 2017 1:54 PM

Positioning the tool (figure 4).

The application tool can be offset in 30° steps

and fastened in the most favorable working

position.

Ejecting the application tool (figure 5).

To eject the application tool and have the

starting position set, move the clamping lever

back to the stop; in this, the application tool

is also released.

Pay attention that the application tool is

seated straightly the tool holder.

For all work or when changing application

tools, always wear protective gloves.

Danger of injury from the sharp edges of the

application tools. Application tools can

become very hot while working. Danger of

burns!

Fig. 4

0°

30°

60°

90°

60°

30°

180 °

Fig. 5

180°

OBJ_BUCH-0000000240-003.book Page 13 Tuesday, August 15, 2017 1:54 PM

Dust extraction (figure 6).

Mount the dust extraction.

Afterwards, mount the desired sanding sheet.

Connect a vacuum cleaner.

Fig. 6

OBJ_BUCH-0000000240-003.book Page 14 Tuesday, August 15, 2017 1:54 PM

Working instructions.

Before mounting or replacing cutting tool or accessories, pull the power plug.

This preventive safety measure rules out the danger of injuries through acciden-

tal starting of the power tool.

Do not use accessories not specifically intended and recommended for this power tool by FEIN.

The use of non-original FEIN accessories can lead to overheating of the power tool and destroy

it.

For each job, use only the FEIN application tool released and intended for the

respective application.

Switching on and off (figure 7).

Always hold the power tool

firmly. Otherwise, you could

lose control over the power tool.

Guide the power tool toward the work

piece only when switched on.

Switching on:

Push the switch toward the front (I).

Switching off:

Push the switch toward the rear ().

Setting the oscillating frequency

(figure 8).

Adjust the oscillating frequency infinitely vari-

able with the dial control.

Turn the dial control between “1” for the

lowest speed and “6” for the highest speed.

WARNING

CAUTION

Fig. 7

On/Off switch

Thumbwheel for

pre-selection of

oscillating frequency

Fig. 8

OBJ_BUCH-0000000240-003.book Page 15 Tuesday, August 15, 2017 1:54 PM

Notes on sanding.

Press the power tool with the sanding sheet

briefly and firmly against a flat surface and

briefly switch the power tool on. This pro-

vides for good adhesion and prevents prema-

ture wear.

When only one tip or corner of the sanding

sheet is worn, it can be removed again and

reattached, turned by 120°.

Work with the entire surface of the sanding

plate, not only with the tip.

When sanding with small triangle sanding

plates, select a high oscillating frequency

(electronics level 4 – 6); when sanding with

the round sanding plate and the large triangle

sanding plate, select a moderate oscillating

frequency (max. electronics level 4).

Sand with continuous motion applying mod-

erate pressure. Applying excessive pressure

does not increase the rate of removal, it only

wears off the sanding sheet faster.

Notes on profile sanding.

Select a medium oscillating frequency.

Notes on sawing.

Select a high oscillating frequency. Round saw

blades can be released and clamped offset

again, to allow for uniform wearing off.

Notes on scraping.

Select a moderate to high oscillating fre-

quency.

OBJ_BUCH-0000000240-003.book Page 16 Tuesday, August 15, 2017 1:54 PM

Repair and customer service.

Before mounting or replacing cutting tool or accessories, pull the power plug.

This preventive safety measure rules out the danger of injuries through acci-

dental starting of the power tool.

Exchangeable parts

If required, you can change the following

parts yourself:

Application tools

Service.

Have maintenance carried out

only through qualified person-

nel. Incorrectly mounted leads and compo-

nents can cause serious injuries. Have the

required service carried out only through a

FEIN customer service agent.

The current spare parts list for this power

tool can be found in the Internet at

www.fein.com.

Cleaning.

Prior to any cleaning or main-

tenance, disconnect the

power tool from the power supply in order to

avoid accidents.

When using in environments

with conductive dust in the

air, such as when working metals, this dust

can settle in the interior of the power tool.

This can impair the total insulation of the

power tool. Therefore, regularly blow out the

interior of the power tool from outside via the

ventilation openings with dry, oil-free com-

pressed air; always wear eye protection when

doing this. For additional protection, connect

a residual current device (RCD) on the line

side.

Do not attempt to clean

clogged or dirty ventilation

openings of the power tool with pointed

metal objects; use nonmetal tools or objects

if necessary.

Do not use cleaning agents

and solvents that can cause

damage to plastic parts. These include: Gas-

oline, carbon-tetrachloride, chloric solvents,

ammonia and domestic cleaning agents that

contain ammonia.

If the supply cable of this

power tool is damaged, it

must be replaced by a specially prepared cable

available through the FEIN customer service

center.

Warranty and liability.

The warranty for the product is valid in accordance with the legal regulations in the country

where it is marketed. In addition, FEIN also provides a guarantee in accordance with the FEIN

manufacturer’s warranty declaration.

Not all accessories described or shown in this instruction manual will be included with your-

power tool.

Environmental protection, disposal.

Packaging, worn out power tools and accessories should be sorted for environmental-friendly

recycling.

WARNING

CAUTION

OBJ_BUCH-0000000240-003.book Page 17 Tuesday, August 15, 2017 1:54 PM

Pour votre sécurité.

Lisez tous les avertisse-

ments de sécurité et

toutes les instructions. Ne pas suivre les aver-

tissements et instructions peut donner lieu à

une électrocution, un incendie et/ou une

blessure sérieuse.

Conservez tous les avertissements et toutes

les instructions pour pouvoir vous y reporter

ultérieurement.

Ne pas utiliser cet outil électrique avant

d’avoir soigneusement lu et parfaitement

compris cette notice d’utilisation y compris

les figures, les spécifications, les consignes de

sécurité ainsi que les indications marquées par

DANGER, AVERTISSEMENT et ATTEN-

TION.

N’utiliser cet outil électrique que pour les tra-

vaux pour lesquels il a été conçu par FEIN.

N’utiliser que des outils de travail et accessoi-

res autorisés par FEIN.

De même, respectez les dispositions concer-

nant la prévention des accidents du travail en

vigueur dans le pays en question.

Le non-respect des instructions de sécurité se

trouvant dans la documentation mentionnée

peut entraîner un choc électrique, un incendie

et/ou de graves blessures.

Bien garder cette notice d’utilisation en vue

d’une utilisation ultérieure ; elle doit être

jointe à l’appareil en cas de transmission ou de

vente à une tierce personne.

GARDER SOIGNEUSEMENT CES INSTRUC-

TIONS DE SECURITE.

Le terme « outil électrique » dans les consi-

gnes de sécurité fait référence à votre outil

électrique alimenté par le secteur (avec cor-

don d’alimentation) ou votre outil fonction-

nant sur batterie (sans cordon

d’alimentation).

Instructions générales de

sécurité.

1) Zone de travail

a)Conserver la zone de travail propre et

bien éclairée. Les zones en désordre ou

sombres sont propices aux accidents.

b)Ne pas faire fonctionner les outils élec-

trique en atmosphère explosive, par

exemple en présence de liquides inflam-

mables, de gaz ou de poussières. Les

outils électroportatifs produisent des

étincelles qui peuvent enflammer les

poussières ou les fumées.

c) Maintenir les enfants et les personnes

présentes à l’écart pendant l’utilisation

de l’outil. Les distractions peuvent vous

faire perdre le contrôle de l’outil.

2) Sécurité électrique

a)Il faut que les fiches de l’outil électrique

soient adaptées au socle. Ne jamais

modifier la fiche de quelque façon que

ce soit. Ne pas utiliser d’adaptateurs

avec des outils à branchement de terre.

Des fiches non modifiées et des socles

adaptés réduiront le risque de choc

électrique.

b)Eviter tout contact du corps avec des

surfaces reliées à la terre telles que les

tuyaux, les radiateurs, les cuisinières et

les réfrigérateurs. Il existe un risque

accru de choc électrique si votre corps

est relié à la terre.

c) Ne pas exposer les outils à la pluie ou à

des conditions humides. La pénétration

d’eau à l’intérieur d’un outil augmentera

le risque de choc électrique.

d)Ne pas maltraiter le cordon. Ne jamais

utiliser le cordon pour porter, tirer ou

débrancher l’outil. Maintenir le cordon à

l’écart de la chaleur, du lubrifiant, des

arêtes ou des parties en mouvement.

Des cordons endommagés ou emmêlés

augmentent le risque de choc électrique.

e) Lorsqu’on utilise un outil à l’extérieur,

utiliser un prolongateur adapté à l’utili-

sation extérieure. L’utilisation d’un cor-

don adapté à l’utilisation extérieure

réduit le risque de choc électrique.

f) Si l’usage d’un outil dans un emplace-

ment humide est inévitable, utilisez une

alimentation protégée par un dispositif

à courant différentiel résiduel (RCD).

L’usage d’un RCD réduit le risque de

choc électrique.

3) Sécurité des personnes

a)Rester vigilant, regarder ce que vous

êtes en train de faire. Faire preuve de

bon sens dans votre utilisation de l’outil.

Ne pas utiliser un outil lorsque vous êtes

fatigué ou sous l’emprise de drogues,

AVERTISSEMENT

OBJ_BUCH-0000000240-003.book Page 18 Tuesday, August 15, 2017 1:54 PM

d’alcool ou de médicaments. Un

moment d’inattention en cours d’utilisa-

tion d’un outil peut entraîner des bles-

sures graves des personnes.

b)Utiliser un équipement de sécurité. Tou-

jours porter une protection pour les

yeux. Les équipements de sécurité tels

que les masques contre les poussières,

les chaussures de sécurité antidérapan-

tes, les casques ou les protections

acoustiques utilisés pour les conditions

appropriées réduiront les blessures de

personnes.

c) Eviter tout démarrage intempestif.

S’assurer que l’interrupteur est en posi-

tion arrêt avant de retirer la fiche de la

prise de courant. Porter les outils en

ayant le doigt sur l’interrupteur ou bran-

cher des outils dont l’interrupteur est en

position marche est source d’accidents.

d)Retirer toute clé de réglage avant de

mettre l’outil en marche. Une clé laissée

fixée sur une partie tournante de l’outil

peut donner lieu à des blessures de per-

sonnes.

e) Ne pas se précipiter. Garder une posi-

tion et un équilibre adaptés à tout

moment. Cela permet un meilleur

contrôle de l’outil dans des situations

inattendues.

f) S’habiller de manière adaptée. Ne pas

porter de vêtements amples ou de

bijoux. Garder les cheveux, les vête-

ments et les gants à distance des par-

ties en mouvement. Des vêtements

amples, des bijoux ou les cheveux longs

peuvent être pris dans des parties en

mouvement.

g)Si des dispositifs sont fournis pour le

raccordement d’équipements pour

l’extraction et la récupération des pous-

sières, s’assurer qu’ils sont connectés

et correctement utilisés. Utiliser des

collecteurs de poussière peut réduire

les risques dus aux poussières.

4) Utilisation et entretien de l’outil

a)Ne pas forcer l’outil. Utiliser l’outil

adapté à votre application. L’outil adap-

té réalisera mieux le travail et de maniè-

re plus sûre au régime pour lequel il a

été construit.

b)Ne pas utiliser l’outil si l’interrupteur ne

permet pas de passer de l’état de mar-

che à arrêt et vice versa. Tout outil qui

ne peut pas être commandé par l’inter-

rupteur est dangereux et il faut le répa-

rer.

c) Débrancher la fiche de la source d’ali-

mentation en courant et/ou le bloc de

batteries de l’outil avant tout réglage,

changement d’accessoires ou avant de

ranger l’outil. De telles mesures de

sécurité préventives réduisent le risque

de démarrage accidentel de l’outil.

d)Conserver les outils à l’arrêt hors de la

portée des enfants. Ne pas permettre à

des personnes ne connaissant pas

l’outil ou les présentes instructions de le

faire fonctionner. Les outils sont dange-

reux entre les mains d’utilisateurs novi-

ces.

e) Observer la maintenance de l’outil. Véri-

fier qu’il n’y a pas de mauvais aligne-

ment ou de blocage des parties mobiles,

des pièces cassées ou toute autre

condition pouvant affecter le fonction-

nement de l’outil. En cas de dommages,

faire réparer l’outil avant de l’utiliser.

De nombreux accidents sont dus à des

outils mal entretenus.

f) Garder affûtés et propres les outils per-

mettant de couper. Des outils destinés à

couper correctement entretenus avec

des pièces coupantes tranchantes sont

moins susceptibles de bloquer et sont

plus faciles à contrôler.

g)Utiliser l’outil, les accessoires et les

lames etc., conformément à ces instruc-

tions et aux prescriptions en vigueur

pour ce type d’appareil. Tenir compte

également des conditions de travail et

du travail à réaliser. L’utilisation de

l’outil pour des opérations différentes

de celles prévues pourrait donner lieu à

des situations dangereuses.

5) Maintenance et entretien

a)Faire entretenir l’outil par un réparateur

qualifié utilisant uniquement des pièces

de rechange identiques. Cela assurera

que la sécurité de l’outil est maintenue.

OBJ_BUCH-0000000240-003.book Page 19 Tuesday, August 15, 2017 1:54 PM

Instructions particulières de sécurité.

Tenir l’outil par les surfaces de préhension

isolées, lors de la réalisation d’une opération

au cours de laquelle l’organe de coupe peut

entrer en contact avec un câblage non appa-

rent ou son propre cordon d’alimentation. Le

contact avec un fil « sous tension » peut éga-

lement mettre « sous tension » les parties

métalliques exposées de l’outil électrique et

provoquer un choc électrique sur l’opérateur.

Utiliser des bornes ou une autre méthode pra-

tique pour bloquer et soutenir la pièce sur un

support stable. Si vous ne tenez la pièce que

par votre main ou contre votre corps, elle est

dans une position instable, ce qui peut entraî-

ner une perte de contrôle.

N’utilisez pas des accessoires qui n’ont pas

été spécialement conçus ou autorisés par le

fabricant de l’outil électrique. Le seul fait

qu’un accessoire puisse être monté sur votre

outil électrique ne garantit pas une utilisation

sans risque.

Tenir l’outil électrique fermement, en faisant

attention à ce que votre corps ne puisse

jamais entrer en contact avec l’outil de tra-

vail, en particulier lorsque vous travaillez

avec des outils dirigés vers la poignée tels

que lames de scie ou outils de coupe. Le

contact avec des bords ou coins tranchants

peut entraîner des blessures.

Porter un équipement de protection indivi-

duelle. En fonction de l’application, utiliser un

écran facial, des lunettes de sécurité ou des

verres de sécurité. Le cas échéant, utiliser un

masque antipoussières, des protections audi-

tives, des gants et un tablier capables d’arrê-

ter les petits fragments abrasifs ou des

pièces à usiner. La protection oculaire doit

être capable d’arrêter les débris volants pro-

duits par les diverses opérations. Le masque

antipoussières ou le masque respiratoire doit

être capable de filtrer les particules produites

par vos travaux. L’exposition prolongée aux

bruits de forte intensité peut provoquer une

perte de l’audition.

Ne dirigez pas l’outil électrique vers vous-

même ou vers d’autres personnes ou des ani-

maux. Il y a un danger de blessure causé par

des outils de travail tranchants ou chauds.

Il est interdit de visser ou de riveter des pla-

ques ou des repères sur l’outil électrique.

Une isolation endommagée ne présente

aucune protection contre une électrocution.

Utilisez des autocollants.

Nettoyez régulièrement les ouïes de ventila-

tion de l’outil électrique avec des outils non-

métalliques. La ventilation du moteur aspire

la poussière à l’intérieur du carter. Une trop

grande quantité de poussière de métal accu-

mulée peut provoquer des incidents électri-

ques.

Avant la mise en service, assurez-vous que le

câble de raccordement et la fiche sont en par-

fait état.

Recommandation : Faites toujours fonction-

ner l’outil électrique sur un réseau électrique

équipé d’un disjoncteur différentiel 30 mA

max.

Maniement de poussières nocives.

Lors du travail avec des

outils, par ex. lors du

ponçage, polissage, sciage ou d’autres opéra-

tions enlevant du matériau, des poussières

sont générées qui peuvent être nocives pour

la santé, auto-inflammables ou explosives.

Toucher ou aspirer certaines poussières peut

causer des réactions allergiques et/ou des

maladies respiratoires, un cancer, des malfor-

mations à la naissance ou autres anomalies de

reproduction auprès de l’utilisateur ou de

personnes se trouvant à proximité.

Quelques exemples de tels matériaux et des

produits chimiques qu’ils contiennent dont

l’usinage génère des poussières nocives :

– l’amiante et les matériaux contenant de

l’amiante ;

– peintures contenant du plomb, certains

bois tels que le bois de chêne et de hêtre ;

– minéraux et métal ;

– les particules de silicate contenues dans les

briques, le béton et autres matériaux

contenant de la roche ;

– les solvants contenus dans les vernis et

peintures ;

– l’arsenic, le chrome et d’autres lazures ;

AVERTISSEMENT

OBJ_BUCH-0000000240-003.book Page 20 Tuesday, August 15, 2017 1:54 PM

La page charge ...

FEIN MultiMaster Top Manuel utilisateur

Marque: FEIN

Modèle: MultiMaster Top

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Ce manuel convient également à

72295267090

Télécharger le PDF

rapport

dans d''autres langues

English: FEIN MultiMaster Top User manual
español: FEIN MultiMaster Top Manual de usuario

FEIN MultiMaster Top Manuel utilisateur

Ce manuel convient également à

FEIN MultiMaster Top Manuel utilisateur

dans d''autres langues

Documents connexes