Maytag MLG20PDCWW0 Guide d'installation

Marque: Maytag

Modèle: MLG20PDCWW0

Catégorie: Machines à laver

Taper: Guide d'installation

Ce manuel convient également à

INSTALLATIONINSTRUCTIONS

COMMERCIALFRONT LOADWASHER

INSTRUCTIONSPOUR UINSTALLATION

LAVEUSE COMMERCIALE A CHARGEMENT FRONTAL

Table of Contents/Table des matieres ................................2

W10353871A

www.maytagcommerciallaundry.com

TABLEOFCONTENTS

WASHER SAFETY .......................................................................... 2

INSTALLATION REQUIREMENTS ................................................ 3

Tools and Parts ............................................................................ 3

Accessories .................................................................................. 4

Options ......................................................................................... 4

Location Requirements ................................................................ 4

Drain System ................................................................................ 5

Electrical Requirements ............................................................... 6

INSTALLATION INSTRUCTIONS .................................................. 6

Remove Transport System .......................................................... 6

Connect the Inlet Hoses ............................................................... 7

Connect the Drain Hose ............................................................... 8

Secure the Drain Hose ................................................................. 8

Level the Washer .......................................................................... 9

Installing Pad Strips ..................................................................... 9

Complete Installation ................................................................... 9

USER & SET-UP INSTRUCTIONS .............................................. 10

General User Information ........................................................... 10

Control Set-up Procedures ........................................................ 10

Start Operating Set-up ............................................................... 11

WASHER CARE ............................................................................ 14

ASSISTANCE OR SERVICE ......................................................... 15

WAR RANTY .................................................................................. 16

TABLEDESMATIERES

SleCURITle DE LA LAVEUSE ........................................................ 17

EXIGENCES D'INSTALLATION ................................................... 18

Outillage et pieces ...................................................................... 18

Accessoires ................................................................................ 18

Options ....................................................................................... 19

Exigences d'emplacement ......................................................... 19

Systeme de vidange ................................................................... 20

Specifications electriques .......................................................... 20

INSTRUCTIONS D'INSTALLATION ............................................. 21

Depose du systeme de transport............................................... 21

Raccordement des tuyaux d'alimentation ................................. 22

Raccordement du tuyau de vidange .......................................... 23

Immobilisation du tuyau de vidange .......................................... 23

Reglage de I'aplomb de la laveuse ............................................ 24

Installation des bandes de protection ........................................ 24

Achever I'installation .................................................................. 24

INSTRUCTIONS D'UTILISATION ET D'INSTALLATION ...........25

Informations gen6rales pour I'utilisateur .................................... 25

Procedures de reglage des systemes de commande ............... 25

Parametrage pour mise en marche ........................................... 26

ENTRETIEN DE LA LAVEUSE ..................................................... 29

ASSISTANCE OU SERVICE ......................................................... 30

GARANTIE ..................................................................................... 31

WASHER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions,

including the following:

[] Read all instructions before using the washer.

[] Do not wash articles that have been previously cleaned

in, washed in, soaked in, or spotted with gasoline,

dry=cleaning solvents, other flammable, or explosive

substances as they give off vapors that could ignite or

explode.

[] Do not add gasoline, dry=cleaning solvents, or other

flammable, or explosive substances to the wash water.

These substances give off vapors that could ignite or

explode.

[] Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been used

for 2 weeks or more. HYDROGEN GAS IS

EXPLOSIVE. If the hot water system has not been

used for such a period, before using the washing

machine, turn on all hot water faucets and let the water

flow from each for several minutes. This will release

any accumulated hydrogen gas. As the gas is

flammable, do not smoke or use an open flame during

Do not allow children to play on or in the washer. Close

supervision of children is necessary when the washer is used

near children.

Before the washer is removed from service or discarded,

remove the door or lid.

[] Do not reach into the washer if the drum, tub or agitator is

moving.

[] Do not install or store the washer where itwill be exposed to

the weather.

[] Do not tamper with controls.

[] Do not repair or replace any part of the washer or attempt any

servicing unless specifically recommended in this manual or in

published user-repair instructionsthat you understand and

have the skills to carry out.

[] See "Electrical Requirements" located in the installation

instructionsfor grounding instructions.

this time.

SAVE THESE iNSTRUCTiONS

INSTALLATIONREQUIREMENTS

Parts supplied for PD Models:

Gather the required tools and parts before starting installation.

The parts supplied are in the washer drum.

Tools needed for connecting the water inlet hoses

• Pliers (that open to • Flashlight (optional)

19/16"[39.5 mm])

Tools needed for installation

• Open end wrenches 1/2" and 9/16" • Level

• TorxC_tT-20 Security screwdriver • Wood block

• 1/4" nut driver • Ruler or

measuring tape

Parts supplied

Service door lock cam

Parts supplied for PR Models:

Foampads

Card reader bezel

Screws (2)

A. U-shaped hose form

B. Water inlet hoses (2)

C. Inlet hose washers (4)

D. Transit bolt hole plug (4)

E. Beaded tie strap

F. Drain hose

G. Hose clamp

1® TORX is a registered trademark of Saturn Fasteners, Inc.

Alternate Parts

Your installation may require additional parts. Ifyou are interested

in purchasing one of the items listed here, call the toll-free

number in the "Assistance or Service" section.

If You Have You Will Need to Buy

Laundry tub or Sump pump system (if not already

standpipe taller available)

than 96" (2.4 m)

Overhead sewer

Standard 20 gal. (76 L), 30" (762 mm) tall

drain tub or utility sink and sump pump

(available from local plumbing suppliers)

Floor drain

Siphon break, Part Number 285834;

additional drain hose,

Part Number 8318155; and connector

kit, Part Number 285835

Drain hose 4 ft (1.2 m) drain hose extension kit,

too short Part Number 285863

Water faucets 2 longer water fill hoses:

beyond reach 6 ft (1.8 m) Part Number 76314

of fill hoses 10 ft (3.0 m) Part Number 350008

Enhance your washer with these premium accessories.

For more high-quality items or to order, call 1-800-901-2042,

or visit us at www.maytag.com/accessories. In Canada call:

1-800-807-6777 or visit us at www.whirlpoolparts.ca.

Part Accessory

Number

8212526 Washer drip tray, fits under all

31682 All purpose appliance cleaner

1903WH Laundry supply storage cart

Pedestal

You have the option of purchasing pedestals separately for this

washer. The pedestal will add to the total height of the washer.

Optional pedestal

Pedestal Approximate Color Model

Height height with Number

washer

27/8"(73 mm) 47.5" (1207 mm) White WHP0400VW

NOTE: Some models have pedestal pre-installed.

Selecting the proper location for your washer improves

performance and minimizes noise and possible washer "walk."

Your washer can be installed under a custom counter, or in a

basement, laundry room, or recessed area. See "Drain System."

Companion appliance location requirements should also be

considered. Proper installation is your responsibility.

You will need

A water heater set to deliver 120°F (49°C) water to the

washer.

A grounded electrical outlet located within 6 ft (1.8 m) of

where the power cord is attached to the back of the washer.

See "Electrical Requirements."

• Hot and cold water faucets located within 4 ft (1.2 m)

of the hot and cold water fill valves, and water pressure

of 20-100 psi (137.9-689.6 kPa).

• A level floor with a maximum slope of 1" (25 mm) under entire

washer. Installing the washer on soft floor surfaces, such as

carpets or surfaces with foam backing, is not recommended.

• A sturdy and solid floor to support the washer with a total

weight (water and load) of 400 Ibs (180 kg).

Do not operate your washer in temperatures below 32°F (0°C).

Some water can remain in the washer and can cause damage

in low temperatures.

Installation clearances

• The location must be large enough to allow the washer door

to be fully opened.

• Additional spacing should be considered for ease of

installation and servicing. The door opens more than 90°

and it is not reversible.

• Additional clearances might be required for wall, door, and

floor moldings.

• Additional spacing of 1" (25 mm) on all sides of the washer

is recommended to reduce noise transfer.

Companion appliance spacing should also be considered.

Washer Dimensions

_ 445/8`'

3713/1s.(1134mm}

(961 rnm}

Door is not reversible.

A floor drain should be provided under the bulkhead.

Prefabricated bulkheads with electrical outlets, water inlet lines,

and drain facilities should be used only where local codes permit.

The washer can be installed using the standpipe drain system

(floor or wall), the laundry tub drain system, or the floor drain

system. Select the drain hose installation method you need.

See "Tools and Parts."

Standpipe drain system - wall or floor (views A & B)

The standpipe drain requires a minimum diameter standpipe of

2" (50 mm). The minimum carry-away capacity can be no less

than 10 gal. (38 L) per minute.

The top of the standpipe must be at least 30" (762 mm) high

and no higher than 96" (2.4 m) from the bottom of the washer.

Laundry tub drain system (view C)

The laundry tub needs a minimum 20 gal. (76 L) capacity. The top

of the laundry tub must be at least 30" (762 mm) above the floor.

Floor drain system (view D)

The floor drain system requires a siphon break that may be

purchased separately. See "Tools and Parts."

The siphon break must be a minimum of 28" (710 mm) from the

bottom of the washer. Additional hoses might be needed.

C D

• Do not have a fuse in the neutral or ground circuit.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter,

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

• A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical

supply is required. A time-delay fuse or circuit breaker is

recommended. It is recommended that a separate circuit

serving only this washer be provided.

• This washer is equipped with a power supply cord having a

3 prong grounding plug.

• To minimize possible shock hazard, the cord must be

plugged into a mating, 3 prong, grounding-type outlet,

grounded in accordance with local codes and ordinances. If a

mating outlet is not available, it is the personal responsibility

and obligation of the customer to have the properly grounded

outlet installed by a qualified electrician.

• If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

• Do not ground to a gas pipe.

• Check with a qualified electrician if you are not sure the

washer is properly grounded.

GROUNDING INSTRUCTIONS

For a grounded, cord-connected washer:

This washer must be grounded. In the event of a malfunction

or breakdown, grounding will reduce the risk of electrical

shock by providing a path of least resistance for electric

current. This washer is equipped with a cord having an

equipment-grounding conductor and a grounding plug. The

plug must be plugged into an appropriate outlet that is

properly installed and grounded in accordance with all local

codes and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or serviceman if you are in

doubt as to whether the appliance is properly grounded.

Do not modify the plug provided with the appliance - if it will

not fit the outlet, have a proper outlet installed by a qualified

electrician.

For a permanently connected washer:

This washer must be connected to a grounded metal,

permanent wiring system, or an equipment grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead on

the appliance.

INSTALLATIONINSTRUCTIONS

Use two or more people to move and install washer. I

Failure to do so can result in back or other injury.

IMPORTANT: Position the washer so that the rear of the washer

is within approximately 3 ft (900 ram) of its final location.

There are 4 shipping bolts in the rear panel of the washer that

support the suspension system during transportation. These

bolts also retain the power cord inside the washer until the bolts

are removed.

1. Keep the washer in the upright position while removing the

shipping bolts.

Shipping bolt I

Shipping bolt with plastic spacer

2. Using a 1/2" wrench, loosen each of the bolts. 3. Using pliers, tighten the couplings with an additional

two-thirds turn.

Once the bolt is loose, move it to the center of the hole

and completely pull out the bolt, including the plastic spacer

covering the bolt.

NOTE: Do not overtighten or use tape or sealants on the valve.

Damage to the valves can result.

Clear water lines

Run water through both faucets and inlet hoses, into a

laundry tub, drainpipe, or bucket, to get rid of particles

in the water lines that might clog the inlet valve screens.

Check the temperature of the water to make sure that the hot

water hose is connected to the hot water faucet and that the

cold water hose is connected to the cold water faucet.

4. Once all 4 bolts are removed, discard the bolts and spacers.

Then push the power cord plug into the opening on the right

side of the rear panel and pull the power cord through the

opening on the left side of the rear panel and close holes with

the attached cap. Do not pull plug end of power cord through

the right side hole.

5. Close the bolt holes with the 4 transport bolt hole plugs.

NOTE: If the washer is to be transported at a later date, call your

product distributor or installer. Toavoid suspension and structural

damage, your washer must be properly set up for relocation by a

trained professional.

" I;!e _4_/I1;,8_/Os@>

Insert new flat washers (supplied) into each end of the inlet

hoses. Firmly seat the washers in the couplings.

A B

A. Coupling

B. Washer

Connect inlet hoses to washer

Connect inlet hoses to water faucets

Make sure the washer drum is empty.

1. Attach a hose to the hot water faucet. Screw on coupling

by hand until it is seated on the washer.

2. Attach a hose to the cold water faucet. Screw on coupling

by hand until it is seated on the washer.

C. Cold water inlet

H. Hot water inlet

Attach the hot water hose to the washer's hot (H) water inlet

valve. Screw on coupling by hand until it is seated on the

washer.

2. Attachthecoldwaterhosetothewasher'scold(C)water

faucet.Screwoncouplingbyhanduntilitisseatedonthe

washer.

3. Usingpliers,tightenthecouplingswithanadditional

two-thirdsturn.

NOTE:Donotovertighten.Damagetothecouplingcan

result.

Turn on the water faucets completely and check for leaks and

at washer connection.

NOTE: Replace inlet hoses after 5 years of use to reduce the

risk of hose failure. Record hose installation or replacement

dates on the hoses for future reference.

Periodically inspect and replace hoses if bulges, kinks, cuts,

wear, or leaks are found.

Remove drain hose from washer drum

1. Use locking pliers, squeeze hose clamp tabs together and insert

over the end of drain hose.

2. Slide drain hose onto washer connection.

3. Once drain hose is in place, release pliers.

Washer drain system can be installed using a floor drain, wall

standpipe, floor standpipe, or laundry tub.

Laundry tub drain or standpipe drain

Connect the drain hose form to the corrugated drain hose.

To keep drain water from going back into the washer:

• Use the drain hose form, and do not force excess drain hose

into standpipe. Hose should be secure, but loose enough to

provide a gap for air.

• Do not lay excess hose on the bottom of the laundry tub.

Floor drain

You may need additional parts. See Floor drain under "Tools

and Parts."

Drain hose must be secured to stop the hose from moving when

water is pumped out. If the drain hose moves, water may end up

on the floor.

1. Drape the power cord over the washer top.

2. Move the washer to its final location.

3. Place the drain hose in the laundry tub or standpipe as shown.

See illustrations A and B.

(114 ram)

ii (111!Ii,=>

NOTES:

• Do not force excess drain hose back into the rear of the

washer.

• To avoid siphoning, do not seal or put more than 41/2"

(114 mm) of the drain hose into drainpipe or standpipe.

• If the washer faucets and the drain standpipe are recessed,

put the hooked end of the drain hose in the standpipe as

shown. See illustration C.

Properly leveling your washer avoids excessive noise and

vibration.

1. Check the levelness of the washer by placing a level on the

top edge of the washer, first side to side, then front to back.

Install the pads on the left and right inside walls of the coin

vault, leaving about 1/4 to 1/2 inch of space near the front

edge of the vault to allow room for the coin box to lock into

position.

I I

.... ..-.._-b_

If the washer is against a wall, move the washer out slightly

before tipping back. If the washer is not level, first prop the

front with a wood block and adjust the feet as necessary;

then prop the back and adjust feet as necessary. Repeat this

step until washer is level.

Make sure all four feet are stable and resting on the floor.

Then check that the washer is level (use a level).

After the washer is level, use a 9/1 6" open-end wrench to turn

the nuts on the feet tightly against the washer cabinet.

IMPORTANT: All four feet must be tightened. If the nuts are

not tight against the washer cabinet, the washer may vibrate.

The washer should not move front to back, side to side, or

diagonally when pushed on its top edges.

Slide the washer to its final location.

Confirm the levelness of the washer.

NOTE: For PD Models only.

1. Take the 2 foam pad strips from bag.

2. Remove the tape from the back of the adhesive pads.

A. Foam pad strips

1. Check the electrical requirements. Be sure that you have the

correct electrical supply and the recommended grounding

method. See "Electrical Requirements."

2. Check that all parts are now installed. If there is an extra part,

go back through the steps to see which step was skipped.

3. Check that you have all of your tools.

4. Dispose of/recycle all packaging materials.

5. Check that the water faucets are on.

6. Check for leaks around faucets and inlet hoses.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Plug into a grounded 3 prong outlet.

To test and to clean your washer, measure 1/2 the detergent

manufacturer's recommended amount of High Efficiency (HE)

detergent for a medium-size load. Pour the detergent into the

detergent dispenser. Select any cycle and allow the washer to

complete one whole cycle.

USER&SET.UPINSTRUCTIONS

NOTE: After the washer has been installed and plugged in, the

display will show '0 MINUTES'. Once the washer has been

plugged in and the washer door opened and closed, the display

will show the price. In washers set for free cycles, the display will

flash 'SELECT CYCLE'.

1. PD Models: Insert coins until 'SELECT CYCLE' flashes

in display.

PR Models: A debit card is required rather than coins. In

Enhanced Debit mode, the card balance will also display

when a debit card is inserted into the reader.

2. Door must be closed before cycle selection is made,

3. Press fabric setting button for the wash cycle desired. After

the cycle is started, the time will display and count down.

4. If a cycle is interrupted by opening the door, 'RESELECT

CYCLE' will flash in the display. To restart the washer, close

door, and reselect desired cycle.

(i '_-% _ -_ _,

SCROLLING 'OUT OF ORDER' SHOWING IN DISPLAY - This

condition indicates the washer is inoperative.

"0 MINUTES" SHOWING IN DISPLAY -This indicates the cycle is

complete and the washer cannot be operated. Coins dropped or

debit inputs during this condition will be stored in escrow but

cannot be used until normal operation is restored by opening and

closing the door. If a door switch fails, it must be replaced before

normal operation can be restored.

COLD START (Initial first use) - Washer is programmed at the

factory as follows:

Washer 11-minute wash period

3 rinses (extra rinse not enabled)

$1.75 wash price (PD models)

$0.00 wash price (PR models)

WARM START (after power failure) - A few seconds after power

is restored, if a cycle was in progress at the time of the power

failure, 'RESELECT CYCLE' will flash in the display, indicating the

need for a key press to restart washer.

DOOR LOCK - Prior to beginning a cycle, there is a door lock

routine of IocWunlocWrelock then cycle begins. The door will

remain locked until the end of a cycle or approximately 2 minutes

after a power interruption.

PRICING - After the door is opened following the completion

of a cycle, the display indicates the cycle price (unless set for

free operation). As coins are dropped or debit inputs arrive,

the display will change to lead the user through the initiation

of a cycle.

FREE CYCLES - This is established by setting the cycle price to

zero. When this happens, 'SELECT CYCLE' will appear rather

than a cycle price.

DEBIT CARD READY - This washer is debit card 'cable' ready. It

will accept a variety of debit card systems, but does NOT come

with a debit card reader. Refer to the debit card reader

manufacturer for proper washer set-up. In models converted

to a Generation 1 debit card system, debit pulses represent

the equivalent of one coin (coin 1).

IMPORTANT: Read all instructions before operating.

PD Models: Insert service door key, turn, and lift to remove

access door.

PR Models: Once the debit card reader is installed (according

to the reader manufacturer's instructions), the set-up can be

entered by inserting a set-up card (supplied by the reader

manufacturer) into the card slot.

The lower fabric setting buttons and the digital display are used

to set up the controls.

The display can contain 4 numbers and/or letters and a decimal

point. These are used to indicate the set-up codes and related

code values available for use in programming the washer.

HOW TO USE THE BU'B'ONS TO PROGRAM THE

CONTROLS

1. PERM PRESS button is used to adjust the

values associated with set-up codes. Pressing the button

will change the value by increments. Rapid adjustment

is possible by holding the button down.

2. DELICATES AND KNITS button will advance through the set-

up codes. Pressing the button will advance to the next

available set-up code. Holding the button down will

automatically advance through the set-up codes at a rate

of 1 per second.

3. QUICK CYCLE button is used to select or deselect options.

Before proceeding, it is worth noting that, despite all of the

options available, an owner can simply choose to uncrate a new

commercial washer, hook it up, plug it in, and have a washer that

operates.

Washers are preset at the factory for a 11-minute wash period

and 3 rinses (no extra rinse).

SET-UP CODES

The DELICATES AND KNITS button will advance from code to

code. The PERM PRESS button will change the code value. The

QUICK CYCLE button will select or deselect options.

FOR PR MODELS: The set-up codes are the same as for the

"PD" model except where noted.

The set-up code is indicated by the one or two left-hand

characters. The set-up code value is indicated by the two or

three right-hand characters.

CODE EXPLANATION

6 07 REGULAR CYCLE PRICE (Factory Default)

6 07 Represents the number of quarters (coin 1); may

adjust from 0-39. (See VALUE OF COIN 1.)

Advance from 0-39 by pressing the PERM PRESS

button. Factory default of 7 quarters = $1.75.

6 00 PR MODELS ONLY: Factory default of 0 quarters.

6 01 setting would represent one coin slide

actuation.

-_ Press the DELICATES AND KNITS button once to

advance to next code.

7 11 WASH LENGTH

7 11 This is the number of minutes for WASH. Washer

comes from the factory preset with 11 minutes.

Choose from 9-17 minutes by pressing the PERM

PRESS button.

-_ Press the DELICATES AND KNITS button once to

advance to next code.

NOTE: This option does not apply to QUICK

CYCLE.

8 00 ADDITIONAL RINSE OPTION

This option is either SELECTED 'ON' or NOT

SELECTED 'OFF'.

8 00 Not Selected 'OFF'.

8Ar Selected 'ON'. Cannot be combined with the Super

Cycle rinse option.

Press the QUICK CYCLE button once for this

selection.

-_ Press the DELICATES AND KNITS button once to

advance to next code.

9 00 CYCLE COUNTER OPTION

This option is either SELECTED 'ON' or

NOT SELECTED 'OFF'.

9 00 Not Selected OFF'.

9 0C Selected 'ON' and not able to be deselected.

Press the QUICK CYCLE button 3 consecutive

times to select 'ON'. Once selected 'ON' it cannot

be deselected.

-_ Press the DELICATES AND KNITS button once to

advance to next code.

CODE EXPLANATION

1.00 MONEY COUNTER OPTION

This option is either SELECTED 'ON' or NOT

SELECTED 'OFF'.

1.00 Not Selected 'OFF'.

1.0C Selected 'ON'.

Press the QUICK CYCLE button 3 consecutive

times to select 'ON' and 3 consecutive times to

remove (Not Selected 'OFF'). Counter resets by

going from 'OFF' to 'ON'.

1. CO Selected 'ON' and not able to be deselected. To

select 'ON' and not able to be deselected, first

select 'ON,' then within 2 seconds, press the

QUICK CYCLE twice, the PERM PRESS once, and

exit set-up mode.

-_ Press the DELICATES AND KNITS button once to

advance to next code.

2.00

2. SP

SPECIAL PRICING OPTIONS

This option is either SELECTED 'ON' or NOT

SELECTED 'OFF'.

Not Selected 'OFF', and next available code

will be A.00

Selected 'ON'. Press the QUICK CYCLE button

once for this selection.

If SPECIAL PRICING OPTION is selected, there is access to

codes '3.XX' through '9.XX'.

-_ Press the DELICATES AND KNITS button once to

advance to next code.

3.07

3.00

....,

Options to use if SPECIAL PRICING is selected.

SPECIAL CYCLE PRICE

Represents the number of quarters (coin 1); may

adjust from 0-39. (See VALUE OF COIN 1.)

Advance from 0-39 by pressing the PERM PRESS

button. Factory default of 7 quarters = $1.75

PR MODELS ONLY: Factory default of 0 quarters.

Press the DELICATES AND KNITS button once to

advance to next code.

5.00 TIME-OF-DAY CLOCK, MINUTES

5.00 This is the TIME-OF-DAY CLOCK, minute setting;

select 0-59 minutes by pressing the PERM PRESS

button.

-_ Press the DELICATES AND KNITS button once to

advance to next code.

6.00

TIME-OF-DAY CLOCK, HOURS

NOTE: Uses military time or 24 hr. clock

This is the TIME-OF-DAY CLOCK, hour setting;

select 0-23 hours by pressing the PERM PRESS

button.

Press the DELICATES AND KNITS button once to

advance to next code.

7.00

SPECIAL PRICE START HOUR

NOTE: Uses military time or 24 hr. clock

This is the start hour; 0-23 hours. Select START

HOUR by pressing the PERM PRESS button.

Press the DELICATES AND KNITS button once to

advance to next code.

CODE EXPLANATION

8.00 SPECIAL PRICE STOP HOUR

NOTE: Uses military time or 24 hr. clock

8.00 This is the stop hour; 0-23 hours. Select STOP

HOUR by pressing the PERM PRESS button.

-_ Press the DELICATES AND KNITS button once to

advance to next code.

9.10

SPECIAL PRICE DAY

This represents the day of the week and whether

special pricing is selected for that day. A number

followed by '0' indicates no selection that particular

day (9.10). A number followed by an'S' indicates

selected for that day (9.1S). To change the value of

'0' and 'S', use the QUICK CYCLE button.

Days of the week (1-7) are selected by pressing the

PERM PRESS button.

When exiting set-up code '9', the display must show current day

of week:

DISPLAY DAY OF WEEK CODE (selected)

10 Day 1= Sunday 1S

20 Day 2= Monday 2S

30 Day 3= Tuesday 3S

40 Day 4= Wednesday 4S

50 Day 5= Thursday 5S

60 Day 6= Friday 6S

70 Day 7= Saturday 7S

Press the DELICATES AND KNITS button once to

advance to next code

CODE

A. 00

A. SC

EXPLANATION

VAULT VIEWING OPTION

This option is either SELECTED 'ON' or NOT

SELECTED 'OFF'.

Not Selected 'OFF'.

Selected 'ON'. Press the QUICK CYCLE button

once for this selection. When selected, the money

and/or cycle counts will be viewable (if counter

option(s) is selected) when the coin box is

removed.

Press the DELICATES AND KNITS button once to

advance to next code.

b. 05 VALUE OF COIN 1

b. 05 This represents the value of coin 1 in number of

nickels: 05 = $0.25.

By pressing the PERM PRESS button, there is a

option of 1-199 nickels.

-_ Press the DELICATES AND KNITS button once to

advance to next code.

C. 20 VALUE OF COIN 2

C. 20 This represents the value of coin 2 in number of

nickels: 20 = $1.00.

C. 05 PR MODELS ONLY: Factory default of $0.25

By pressing the PERM PRESS button, there is the

option of 1-199 nickels.

-_ Press the DELICATES AND KNITS button once to

advance to next code.

CODE EXPLANATION

d. 00 COIN SLIDE OPTION

This option is either SELECTED 'ON' or NOT

SELECTED 'OFF'. Replacement of meter case will

be needed for coin slide mounting.

d. 00 Not Selected 'OFF'.

d. CS Selected 'ON'.

NOTE: This option needs to be set to "00" unless

the meter case has been changed to accept a coin

slide device. Press the QUICK CYCLE button

3 consecutive times for this selection.

When coin slide mode is selected, set 'b'. equal to

value of vend price in nickels. Set set-up code 6 xx

(regular cycle price) and set-up code 3.xx (special

cycle price) to number of slide operations. If the

installer sets-up 'CS' and a coin drop mechanism is

installed, the washer will not register coins that are

inserted.

-_ Press the DELICATES AND KNITS button once to

advance to next code.

E.O0

E.00

E.AC

ADD COINS OPTION

This option is either SELECTED 'ON' or NOT

SELECTED 'OFF'. This option causes the customer

display to show the number of coins (coin 1) to

enter, rather than the dollars-and-cents amount.

Not Selected 'OFF'.

Selected 'ON'. Press the QUICK CYCLE button

3 consecutive times for this selection.

Press the DELICATES AND KNITS button once to

advance to next code.

E 00 ENHANCED PRICING OPTION

E 00 Not Selected 'OFF'.

R CP Cycle-Based pricing enabled. This option allows

configuration of different prices for cold, warm, and

hot water cycles.

R SU Super Cycle pricing enabled. This option allows

customers to upgrade cycles by depositing extra

money. Set-up codes 'H.' and 'h.' will be displayed

only when this option is enabled. Press the QUICK

CYCLE button for this selection.

-_ Press the DELICATES AND KNITS button once to

advance to next code.

H. 01 SUPER CYCLE UPGRADE PRICE

(Skipped unless Super Cycle pricing is enabled.)

H. 01 This represents the number of coin 1 required

to upgrade a base cycle to a super cycle. Advance

from 0-39 by pressing the PERM PRESS button.

-_ Press the DELICATES AND KNITS button once to

advance to next code.

h. 01 SUPER CYCLE TYPE

(Skipped unless Super Cycle pricing is enabled.)

h. 01 This represents the Super Cycle upgrade option.

Press the PERM PRESS button to step through

upgrade options 1 through 3 as follows:

01 - enhanced wash, extra 3 minutes of wash

tumble in addition to the programmed wash time.

02 - extra rinse for all cycles.

03 - both 01 and 02.

-_ Press the DELICATES AND KNITS button once to

advance to next code.

CODE EXPLANATION

J. Cd COIN/DEBIT OPTION

J. Cd Both coin and debit selected. Press the QUICK

CYCLE button 3 consecutive times to change this

selection.

J. C Coins selected, debit disabled. Press the QUICK

CYCLE button 3 consecutive times to change this

selection.

J. d PR models factory default to J._d. Debit Card

selected, coins disabled. Press the QUICK CYCLE

button 3 consecutive times to change this

selection.

J. Ed Enhanced Debit is self-selected when a

Generation 2 card reader is installed in the washer.

The Ed option cannot be manually selected or

deselected.

-_ Press the DELICATES AND KNITS button once to

advance to next code.

L. 00

L. PS

PRICE SUPPRESSION OPTION

This option causes the customer display to show

'ADD' or 'AVAILABLE' rather than the amount of

money to add. (Used mainly in debit installations.)

Not Selected 'OFF'.

PS Selected 'ON'. Press the QUICK CYCLE button

once for this selection.

Press the DELICATES AND KNITS button once to

advance to next code.

n. CE CLEAR ESCROW OPTION

When selected, money held in escrow for

30 minutes without further escrow or cycle

activity will be cleared.

n. 00 Not Selected 'OFF'.

n. CE Selected 'ON'. Press the QUICK CYCLE button

once for this selection.

-_ Press the DELICATES AND KNITS button once to

advance to next code.

r. 800 TOP SPIN SPEED RPM

r. 800 This can be selected from the following spin

speeds: 600 rpm, 750 rpm, 800 rpm, 1000

(displays as 999) rpm. Step between speeds by

pressing the PERM PRESS button. Factory default

of 800 rpm.

-_ Press the DELICATES AND KNITS button once to

advance to next code.

U. 00

PENNY INCREMENT OFFSET

This represents the penny increment price offset

used in Generation 2 (Enhanced Debit) PR models.

Choose from 0-4 pennies by pressing the PERM

PRESS button.

Press the DELICATES AND KNITS button once to

advance to next code.

A1.00 PREWASH LENGTH

AI. 00 This is the number of minutes of PREWASH.

Choose 0 to disable the prewash or select between

2 and 7 minutes by pressing the PERM PRESS

button.

-_ Press the DELICATES AND KNITS button once to

advance to next code.

CODE EXPLANATION

A2.03 FINAL SPIN LENGTH

A2.03 This is the number of minutes of final high speed

spin. Choose from 3-8 minutes by pressing the

PERM PRESS button.

-_ Press the DELICATES AND KNITS button once to

advance to next code.

If cycle counter (9 0C) is selected, the following is true:

1 00 Number of cycles in 102 = 200

HUNDREDS

2 00

Number of cycles in ONES

2 2,5 = 25

TOTAL CYCLES = 225

This is "VIEW ONLY" and cannot be cleared.

Press the DELICATES AND KNITS button once to advance to

next code.

If money counter (1.0C or 1.C0} is selected, the following

is true:

3 00 Number of dollars in 3 01 = $100.00

HUNDREDS

4 00 Number of dollars in ONES 4 68 = $ 68.00

5 00 Number of CENTS. 5 7,5= $ .75

END of SET-UP PROCEDURES.

Total = $168.75

EXIT FROM SET-UP MODE

PD Models: Reinstall access door.

PR Model: Remove manual set-up cards.

WASHERCARE

Cleaning the Door Seal/Bellow

1. Open the washer door and remove any clothing or items from

the washer.

2. Inspect inner glass door. If debris is present, wipe off debris

using damp cloth.

3. Inspect the colored seal/bellow between the door opening

and the basket for stained areas. Pull back the seal/bellow

to inspect all areas under the seal/bellow and to check for

foreign objects.

A. Seal/Bellow

4. If stained areas are found, wipe down these areas of the

seal/bellow, using the procedure that follows.

a) Mix a dilute solution, using 3/4 cup (177 mL) of liquid

chlorine bleach, and 1 gal. (3.8 L) of warm tap water.

b) Wipe the seal/bellow area with the dilute solution,

using a damp cloth.

c) Let stand 5 minutes.

d) Wipe down area thoroughly with a dry cloth and let the

washer interior air dry with door open.

IMPORTANT:

• Wear rubber gloves when cleaning for prolonged periods.

• Refer to the bleach manufacturer's instructions for proper

use.

Washer Maintenance Procedure

This washer has a special cycle that uses higher water volumes in

combination with liquid chlorine bleach to thoroughly clean the

inside of the washer.

NOTES:

• Read these instructions completely before beginning the

cleaning process.

• If necessary, the cleaning cycle may be interrupted by

pressing the QUICK CYCLE button twice. However, this will

not immediately stop the cycle. The washer will continue with

several rinse and drain steps to ensure that all remaining

bleach is rinsed from the washer.

Begin procedure

1. Open the washer door and remove any clothing or items from

the washer.

2. Use liquid chlorine bleach:

Open the dispenser drawer and immediately add 2/3 cup

(160 mL) of liquid chlorine bleach to the bleach compartment.

NOTE: Do not add any detergent to this cycle. Use of more

than 2/3 cup (160 mL) of bleach will cause product damage

over time.

3. Close the washer door and the dispenser drawer.

4. To start the Washer Cleanout cycle, first enter "Start

Operating Set-up." Then press and hold QUICK CYCLE for

1 second. With the entire display flashing, press BRIGHTS.

NOTE: The door will lock, the basket will rotate 1/2turn, then

the door will unlock and lock again, then the Washer Cleanout

Cycle will continue.

• The washer will not fill, but the basket will rotate while the

washer runs a short sensing cycle. This will take

approximately 3 minutes.

5. The cycle will determine whether clothing or other items are

in the washer.

a) If no items are detected in the washer, it will proceed to

Step 7.

b) If any items are detected in the washer, "rL" or "F-34" will

be displayed. Then the door will unlock.

• Press QUICK CYCLE to cancel the failure code. Then

repeat steps 1,3, and 4 to start the cycle again.

6. Once the cycle has begun, allow the cycle to complete.

7. After the cycle is complete, leave the door open slightly,

to allow for better ventilation and drying of washer interior.

Always do the following to maintain washer freshness

• Use only HE High Efficiency detergent.

• Leave the door slightly open after each cycle to allow for

better ventilation and drying of washer interior.

• Clean the washer monthly using the Washer Maintenance

Procedure, using 2/3 cup (160 mL) of liquid chlorine bleach.

• If the procedure does not sufficiently improve the washer

freshness, please evaluate your installation and usage

conditions for other causes.

Cleaning the exterior

Use a soft damp cloth or sponge to wipe up any spills.

Occasionally wipe the outside of your washer to keep it looking

new. Use mild soap and water. Do not use abrasive products.

Cleaning the dispenser drawer

The dispenser drawer is removable for easy cleaning.

1. Unlock the dispenser drawer by pressing the Release Lever.

Remove the drawer.

2. Remove the inserts (the siphon from the softener and bleach

compartments).

3. Wash the parts under running water.

NOTE: Do not wash components in the dishwasher.

4. Replace the inserts and return the dispenser to the drawer.

Replace inlet hoses after 5 years of use to reduce the risk of hose

failure. Periodically inspect and replace inlet hoses if bulges,

kinks, cuts, wear, or leaks are found.

When replacing your inlet hoses, record the date of replacement.

ASSISTANCEORSERVICE

If you need assistance:

Contact the distributor where the washer was purchased; or

locate an authorized Maytag Commercial Laundry distributor visit

www.maytagcommerciallaundry.com.

When you call, have the washer model number and serial

number. Both numbers can be found on the serial-rating plate

located on your washer.

MAYTAG ® COMMERCIAL SiNGLE-LOAD AND VENDED

MULTi-LOAD WASHER & DRYER

WARRANTY

LIMITED WARRANTY ON PARTS

For the first five years from the date of purchase, when this commercial appliance is installed, maintained and operated according to the

instructions attached to or furnished with the product, Maytag brand of Whirlpool Corporation (thereafter "Maytag") will pay for factory

specified parts or original equipment manufacturer parts to correct defects in materials or workmanship. Proof of original purchase date

is required to obtain service under this warranty.

ITEMS MAYTAG WILL NOT PAY FOR

1. All other costs including labor, transportation, or custom duties.

2. Service calls to correct the installation of your commercial appliance, to instruct you how to use your commercial appliance, to

replace or repair fuses, or to correct external wiring or plumbing.

3. Repairs when your commercial appliance is used for other than normal, commercial use.

4. Damage resulting from improper handling of product during delivery, theft, accident, alteration, misuse, abuse, fire, flood, acts of

God, improper installation, installation not in accordance with local electrical or plumbing codes, or use of products not approved

by Maytag.

5. Pickup and Delivery. This commercial appliance is designed to be repaired on location.

6. Repairs to parts or systems resulting from unauthorized modifications made to the commercial appliance.

7. The removal and reinstallation of your commercial appliance if it is installed in an inaccessible location or is not installed in

accordance with published installation instructions.

8. Chemical damage is excluded from all warranty coverage.

9. Changes to the building, room, or location needed in order to make the commercial appliance operate correctly.

10. Repairs made by a non-Whirlpool authorized service technician.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATIONS OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THiS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED

HEREIN. iMPLiED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. WHIRLPOOL SHALL NOT BE LIABLE FOR

INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES

YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE

TO PROVINCE.

Ifyou need service, please contact your authorized Maytag ® Commercial Laundry distributor. To locate your authorized Maytag ®

Commercial Laundry distributor, or for web inquiries, visit www.MaytagCommercialLaundry.com.

3/10

For written correspondence:

Maytag ® Commercial Laundry Service Department

2000 M-63 North

Benton Harbor, Michigan 49022 USA

# #

SECURITEDELALAVEUSE

Votre s_curit_ et celle des autres est tr_s importante.

Nous donnons de nombreux messages de securit6 importants dans ce manuel et sur votre appareil m6nager. Assurez=vous de

toujours lire tousles messages de s_curit6 et de vous y conformer.

Voici le symbole d'alerte de s6curit&

Ce symbole d'alerte de s6curit_ vous signale les dangers potentiels de d6c_s et de blessures graves #,vous

et & d'autres.

Tous les messages de s_curit6 suivront le symbole d'alerte de s6curit_ et le mot "DANGER" ou

"AVERTISSEMENT". Ces mots signifient :

Risque possible de d_c_s ou de blessure grave si vous ne

suivez pas imm_diaternent les instructions.

Risque possible de d_c_s ou de blessure grave si vous

ne suivez pas les instructions.

Tous les messages de securit6 vous diront quel est le danger potentiel et vous disent comment r6duire le risque de blessure et

ce qui peut se produire en cas de non=respect des instructions.

liViPORTANTES iNSTRUCTiONS DE SECURITI_

AVERTISSEMENT : Pour reduire les risques d'incendie, de choc electrique ou de blessures Iors de I'utilisation de la

laveuse, suivre les pr6cautions fondamentales dont les suivantes :

[] Life toutes les instructions avant d'utiliser la laveuse.

[] Ne pas laver des articles qui ont 6t6 nettoy6s ou

lav6s avec de I'essence ou imbib6s d'essence,

solvants de nettoyage & sec, ou autres substances

inflammables ou explosives; ces substances

peuvent 6mettre des vapeurs susceptibles de

s'enflammer ou d'exploser.

[] Ne pas ajouter d'essence, solvant de nettoyage &

sec ou autre produit inflammable ou explosif darts

I'eau de lavage. Ces substances peuvent emettre

des vapeurs susceptibles de s'enflammer ou

d'exploser.

[] Dans certaines conditions, de I'hydrog6ne gazeux

peut se former dans un circuit d'eau chaude qui n'a

pas 6t6 utilis6 pendant 2 semaines ou plus. LE GAZ

HYDROG#NE EST EXPLOSIBLE. Si le circuit d'eau

chaude n'a pas 6t6 utilis6 pendant une telle p6riode,

avant d'utiliser la laveuse, ouvrir tousles robinets

d'eau chaude et laisser I'eau s'6couler pendant

plusieurs minutes par chaque robinet. Ceci

permettra 1'6vacuation de I'hydrog_ne gazeux

accumul& Comme ce gaz est inflammable, ne pas

fumer ou utiliser une flamme nue au cours de cette

p6riode.

[] Ne pas laisser des enfants jouer sur ou & I'interieur de la

laveuse. Bien surveiller les enfants Iorsque la laveuse est

utilisee & proximite d'enfants.

[] Avant de mettre la laveuse au rebut ou hors de service,

enlever la porte ou le couvercle.

[] Ne pas tenter d'atteindre un article & I'interieur de la cuve de

la laveuse Iorsque le tambour, la cuve ou I'agitateur est en

mouvement.

[] Ne pas installer ou remiser cette laveuse & un endroit oQ elle

serait exposee aux intemperies.

[] Ne pas modifier les organes de commande.

[] Ne pas reparer ou remplacer un composant quelconque de

la laveuse, ni entreprendre une operation de service, si ce

n'est specifiquement recommande dans ce manuel ou dans

un manuel d'instructions de reparations destine &I'utilisateur;

il est alors essentiel que la personne concernee comprenne

ces instructions et soit competente pour les executer.

[] Pour les instructions de liaison & la terre, voir "Specifications

electriques" dans les instructions d'installation.

CONSERVEZ CES iNSTRUCTiONS

EXIGENCESD'INSTALLATION

Rassembler les outils et pieces necessaires avant de commencer

I'installation. Les pieces fournies se trouvent dans letambour de

la laveuse.

Outils n_cessaires au raccordement des tuyaux d'arriv_e

d'eau

• Pince (ouverture jusqu'& • Lampe de poche

19/16"[39,5 mm]) (facultative)

Outils n_cessaires & I'installation

• Cles plates de 1/2" et 9/16"

• Niveau

• Tournevis de securite

Torx ot T-20

• Tourne-ecrou de 1/4"

• Cale en bois

• Regle ou metre ruban

Pibces fournies

A B

Autres pi_ces

IIse peut que I'installation necessite des pieces supplementaires.

Pour acheter I'un des articles indiques ici, composer le numero

sans frais indique sur la couverture ou a la section "Assistance ou

service".

Si vous avez Vous devrez acheter

Evier de buanderie

ou tuyau rigide de

rejet a I'egout plus

haut que 96"

(2,4 m)

I_gout sureleve

I_gout au plancher

Systeme de pompe de puisard (si non

deja disponible)

#vier de vidange standard de 20 gal.

(76 L) de 30" (762 mm) de hauteur ou

evier utilitaire et pompe de puisard

(disponibles chez votre fournisseur local

d'articles de plomberie)

Brise-siphon, piece n° 285834; tuyau de

vidange additionnel, piece n° 8318155; et

ensemble de connexion, piece n° 285835

Tuyau de vidange Trousse de rallonge du tuyau de vidange

trop court de 4 pi (1,2 m), piece n° 285863

Robinets d'eau 2 tuyaux d'admission d'eau plus longs :

hors d'atteinte des 6 pi (1,8 m), piece n° 76314

tuyaux d'admission 10 pi (3 m), piece n° 350008

A. Bride de retenue pour tuyau de vidange (en forme de U)

B. Tuyaux d'arriv#e d'eau (2)

C. Rondelles pour tuyau d'arriv#e d'eau (4)

D. Bouchons pour les trous des boulons de transport (4)

E. Courroie perl#e

F. Tuyau de vidange

G. Bride de tuyau

Pibces fournies pour les modbles PD :

Came de verrouillage

de la porte de service

Bandes de

protection

Vous pouvez faciliter I'utilisation de votre laveuse avec ces

accessoires de premiere qualit&

Pour vous informer au sujet des autres articles de qualite ou

pour commander, composez le 1-800-901-2042 ou consultez

le site www.maytag.com/accessories. Au Canada, composez

le 1-800-807-6777 ou consultez le site Internet

www.whirlpoolparts.ca.

Produit Accessoire

num_ro

8212526 Plateau d'egouttement de la laveuse, convient

&tousles modeles

31682 Produit de nettoyage polyvalent pour

appareils menagers

1903WH Casier de rangement de fournitures de

buanderie

Pibces fournies pour les modules PR :

Biseaude lecteur Vis (2)

de carte

t® TORX est une marque d&pos&e de Saturn Fasteners, Inc.

Pi_destal

Vous avez la possibilite d'acheter des piedestaux separ6ment

pour cette laveuse. Le piedestal augmentera la taille totale de

la laveuse.

Pi#destal facultatif

Hauteur du Hauteur Couleur Num_ro

pi_destal approximative de module

avec laveuse

27/8" (73 mm) 47,5" (1207 mm) Blanc WHP0400VW

REMARQUE : Sur certains modeles, un piedestal est deja

install&

D_gagements de s_paration _ respecter

• L'emplacement doit _tre assez grand pour permettre d'ouvrir

completement la porte de la laveuse.

• Prevoir davantage d'espace pour faciliter I'installation et

I'entretien. La porte s'ouvre a plus de 90 ° et n'est pas

reversible.

• Un espace supplementaire peut _tre requis pour les moulures

de porte et de plancher et pour les plinthes.

• Un espace supplementaire de 1" (25 mm) de tousles c6tes

de la laveuse est recommande pour reduire le transfert du

bruit.

• II faut aussi prendre en compte I'espace requis entre les

appareils voisins.

Dimensions de la laveuse

44%"

(1134 mm I

Le choix d'un emplacement approprie pour la laveuse en

ameliore le rendement et reduit au minimum le bruit et le

"deplacement" possible de la laveuse.

La laveuse peut _tre installee sous un comptoir personnalise,

dans un sous-sol, une salle de buanderie ou un encastrement.

Voir "Systeme de vidange".

IIfaut aussi prendre en compte les exigences d'emplacement

des appareils voisins. C'est a I'utilisateur qu'incombe la

responsabilite de realiser une installation correcte.

II vous faudra

• Un chauffe-eau configure pour fournir de I'eau a 120°F (49°C)

la laveuse.

• Une prise electrique reliee & la terre situee &moins de

6 pi (1,8 m) du cordon d'alimentattion electrique fixe &

I'arriere de la laveuse. Voir "Specifications electriques".

• Des robinets d'eau chaude et d'eau froide situes &moins

de 4 pi (1,2 m) des robinets d'admission d'eau chaude

et d'eau froide et une pression d'eau de 20-100 Ib/po 2

(137,9-689,6 kPa).

• Un plancher de niveau ayant une pente maximale de

1" (25 mm) sous I'ensemble de la laveuse. L'installation de

la laveuse sur des surfaces de sol molles, telles que tapis

ou surfaces avec sous-couche en mousse n'est pas

recommandee.

• Un plancher robuste et solide capable de soutenir le poids

total de la laveuse (eau et charge) de 400 Ib (180 kg).

Ne pas faire fonctionner la laveuse a des temperatures inferieures

32°F (0°C). Une quantite d'eau peut demeurer dans la laveuse

et causer des dommages a des temperatures basses.

(732 ram}

La porte n'est pas r#versible.

Un systeme de vidange au plancher doit _tre installe sous la

cloison. Des cloisons pre-fabriqu6es avec prises de courant,

canalisations d'arrivee d'eau et amenagements pour installation

de vidangeage ne doivent _tre installees que la oQ les codes

Iocaux I'autorisent.

La laveuse peut @treinstall@e en utilisant le syst@me de rejet

I'@gout (au plancher ou mural), le syst@me de vidange de I'@vier

de buanderie ou le syst@me de vidange au plancher. S@lectionner

la m@thode d'installation du tuyau de vidange selon les besoins.

Voir "Outillage et pi@ces".

Syst_me de vidange avec tuyau de rejet _ I'_gout - mural

ou au plancher (vues A et B)

Le systeme de rejet & I'egout necessite un tuyau rigide d'un

diametre minimum de 2" (50 mm). La capacite minimale

d'acheminement ne doit pas etre inferieure & 10 gal. (38 L)

par minute.

Le sommet du tuyau rigide de rejet a I'egout doit etre au moins

30" (762 mm) de hauteur et au maximum a 96" (2,4 m) de la

base de la laveuse.

30" min,

(762 mm)

Syst_me de vidange avec _vier de buanderie (vue C)

L'evier de buanderie doit avoir une capacite minimale de

20 gal. (76 L). La partie superieure de I'evier de buanderie doit

etre a au moins 30" (762 mm) au-dessus du plancher.

Syst_me de vidange au plancher (vue D)

Le systeme de vidange au plancher necessite un brise-siphon

qui peut etre achete separement. Voir "Outillage et pieces".

Le brise-siphon doit etre au moins a 28" (710 mm) de la base

de la laveuse. Des tuyaux supplementaires peuvent etre requis.

28"

Risque de choc _lectrique

Brancher sur une prise & 3 aJv_oles reli_e & la terre.

Ne pas enlever la broche de liaison _ la terre.

Ne pas utiliser un adaptateur.

Ne pas utiliser un c&ble de rallonge.

Le non=respect de ces instructions peut causer

un d_c_s, un incendie ou un choc _lectrique.

Une alimentation de 120 volts, 60 Hz, CA seulement,

de 15 ou 20 amperes, protegee par un fusible est requise.

On recommande d'utiliser un fusible ou un disjoncteur

temporis& II est recommande de raccorder la laveuse

sur un circuit distinct exclusif a cette laveuse.

Cette laveuse comporte un cordon d'alimentation electrique

trois broches pour liaison a la terre.

Pour minimiser les risques de choc electrique, on doit

brancher le cordon sur une prise de courant de configuration

correspondante, a 3 alveoles, reliee a la terre et installee

conformement aux codes et reglements Iocaux. Si une prise

de courant de configuration correspondante n'est pas

disponible, le client a la responsabilite et I'obligation de faire

installer par un electricien qualifie une prise de courant

correctement reliee a la terre.

Si les codes le permettent et si on utilise un conducteur

distinct de liaison a la terre, il est recommande qu'un

electricien qualifie verifie la qualite de la liaison a la terre.

La page charge ...

Maytag MLG20PDCWW0 Guide d'installation

Marque: Maytag

Modèle: MLG20PDCWW0

Catégorie: Machines à laver

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag MLG20PDCWW0 Installation guide

Maytag MLG20PDCWW0 Guide d'installation

Ce manuel convient également à

Maytag MLG20PDCWW0 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents