Hikoki NR3675DD Manuel utilisateur

Handling instructions

Bedienungsanleitung

Mode d’emploi

Istruzioni per l’uso

Gebruiksaanwijzing

Instrucciones de manejo

Instruções de uso

Bruksanvisning

Brugsanvisning

Bruksanvisning

Käyttöohjeet

en

de

fr

it

nl

es

pt

sv

da

no

ﬁ

NR 3675DD

en

de

fr

it

nl

es

pt

sv

da

no

ﬁ

2

NR3675DD

(NNP) (2XCZ)

BSL36A18X

2―2

UC18YSL3

1―1

111

3

1

2

34

4

56

78

910

5

11 12

13 14

15 16

6

17 18

19 20

21

7

22

23 24

ab

25 26

8

337528

BSL36..18..

UC18YSL3 (14,4 V–18 V)

329897

9

English

power source and/or battery pack, picking up or

carrying the tool.

Carrying power tools with your ﬁ nger on the switch

or energising power tools that have the switch on

invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left attached to a rotating part of

the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts.

Loose clothes, jewellery or long hair can be caught in

moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used.

Use of dust collection can reduce dust-related

hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application.

The correct power tool will do the job better and safer

at the rate for which it was designed.

b) Do not use the power tool if the switch does not

turn it on and oﬀ .

Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/

or the battery pack from the power tool before

making any adjustments, changing accessories,

or storing power tools.

Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool.

Power tools are dangerous in the hands of untrained

users.

e) Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may aﬀ ect the

power toolʼs operation.

If damaged, have the power tool repaired before

use.

Many accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions and

the work to be performed.

Use of the power tool for operations diﬀ erent from

those intended could result in a hazardous situation.

5) Battery tool use and care

a) Recharge only with the charger speciﬁ ed by the

manufacturer.

A charger that is suitable for one type of battery pack

may create a risk of ﬁ re when used with another

battery pack.

b) Use power tools only with speciﬁ cally

designated battery packs.

Use of any other battery packs may create a risk of

injury and ﬁ re.

GENERAL POWER TOOL SAFETY

WARNINGS

WARNING

Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in

electric shock, ﬁ re and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂ ammable liquids, gases or dust.

Power tools create sparks which may ignite the dust

or fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools.

Unmodiﬁ ed plugs and matching outlets will reduce

risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators.

There is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase the risk of

electric shock.

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts.

Damaged or entangled cords increase the risk of

electric shock.

e) When operating a power tool outdoors, use an

extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the

risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the inﬂ uence of drugs, alcohol or

medication.

A moment of inattention while operating power tools

may result in serious personal injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ position before connecting to

(Original instructions)

10

English

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects,

that can make a connection from one terminal to

another.

Shorting the battery terminals together may cause

burns or a ﬁ re.

d) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, ﬂ ush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation or

burns.

6) Service

a) Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts.

This will ensure that the safety of the power tool is

maintained.

PRECAUTION

Keep children and inﬁ rm persons away.

When not in use, tools should be stored out of reach of

children and inﬁ rm persons.

CORDLESS DUPLEX NAILER SAFETY

WARNINGS

1. Always assume that the tool contains fasteners.

Careless handling of the nailer can result in unexpected

ﬁ ring of fasteners and personal injury.

2. Do not point the tool towards yourself or anyone

nearby.

Unexpected triggering will discharge the fastener

causing an injury.

3. Do not actuate the tool unless the tool is placed

ﬁ rmly against the workpiece.

If the tool is not contact with the workpiece, the fastener

may be deﬂ ected away from your target.

4. Disconnect the tool from the power source when

the fastener jams in the tool.

While removing a jammed fastener, the nailer may be

accidentally activated if it is plugged in.

5. Use caution while removing a jammed fastener.

The mechanism may be under compression and the

fastener may be forcefully discharged while attempting

to free a jammed condition.

6. Do not use this nailer for fastening electrical cables.

It is not designed for electric cable installation and may

damage the insulation of electric cables thereby causing

electric shock or ﬁ re hazards.

ADDITIONAL SAFETY WARNINGS

1. Safe operation through correct usage.

This tool was designed for driving nails into wood and

similar materials. Use it for its intended purpose only.

2. Be careful of ignition and explosions.

Since sparks may ﬂ y during nailing, it is dangerous to use

this tool near lacquer, paint, benzine, thinner, gasoline,

gas, adhesives and similar inﬂ ammable substances as

they may ignite or explode. Under no circumstances

should this tool therefore be used in the vicinity of such

inﬂ ammable material.

3. Always wear eye protection (protective goggles).

When operating the power tool, always

wear eye protection, and ensure that

surrounding people wear eye protection

too.

The possibility of fragments of the nails that were not

properly hit entering the eye is a threat to sight. Eye

protection can be bought at any hardware store. Always

wear eye protection while operating this tool. Use either

eye protection or a wide vision mask over prescription

glasses.

Employers should always enforce the use of eye

protection equipment.

4. Protect your ears and head.

When engaged in nailing work please wear ear muﬄ ers

and head protection. Also, depending on condition,

ensure that surrounding people also wear ear muﬄ ers

and head protection.

5. Pay attention to those working close to you.

It would be very dangerous if nails that were not properly

driven in should hit other people. Therefore, always pay

attention to the safety of the people around you when

using this tool. Always make sure that nobody’s body,

hands or feet are close to the nail outlet.

6. Never point the nail outlet towards people.

Always assume the tool contains

fasteners.

If the nail outlet is pointed towards people,

serious accidents may be caused if you

mistakenly discharge the tool.

When connecting and disconnecting the battery, during

nail loading or similar operations, be sure the nail outlet

is not pointed towards anyone (including yourself).

Even when no nails are loaded at all, it is dangerous to

discharge the tool while pointing it at someone, so never

attempt to do so. No horseplay. Respect the tool as a

working implement.

7. Check push lever before use.

Make sure the push lever operates properly. (The push

lever may be called “Safety”.) Never use the Nailer

unless the push lever is operating properly, otherwise

the Nailer could drive a fastener unexpectedly. Do not

tamper with or remove the push lever, otherwise the

push lever becomes inoperable.

8. Choice of triggering method is important.

Read and understand section titled “HOW TO USE THE

NAILER” on page 19.

9. Prior to using this product, make sure that it is

operating properly in accordance with the content

of “Testing the nailer” on page 18.

10. Use speciﬁ ed nails only.

Never use nails other than those speciﬁ ed and described

in these instructions.

11. Be careful when connecting the battery.

When connecting the battery and loading nails in

order not to ﬁ re the tool by mistake, make sure of the

followings.

○ Do not touch the trigger.

○ Do not allow the ﬁ ring head to contact with any

surface.

○ Keep the ﬁ ring head down.

Strictly observe the above instructions, and always

make sure that no part of the body, hands or legs is

ever in front of the nail outlet.

12. Do not carelessly place your ﬁ nger on the trigger.

Do not place your ﬁ nger on the trigger except when

actually nailing. If you carry this tool or hand it to

someone while having your ﬁ nger on the trigger, you may

inadvertently discharge a nail and thus cause an accident.

13. Press the nail outlet ﬁ rmly against the material to

be nailed.

When driving in nails, press the nail outlet ﬁ rmly against

the material to be nailed. If the outlet is not applied

properly, the nails may rebound.

11

English

14. Keep hands and feet away from the ﬁ ring head

when using.

It is very dangerous for a nail to hit the

hands or feet by mistake.

15. Beware of the tool’s kickback.

Do not approach the top of the tool with your head etc.

during operation. This is dangerous because the tool

may recoil violently if the nail currently being driven in

comes into contact with a previous nail or a knot in the

wood.

16. Be careful of double ﬁ re due to recoil.

If the push lever is unintentionally allowed to re-contact

the workpiece following recoil, an unwanted fastener will

be driven.

In order to avoid this undesirable double ﬁ re,

○ Intermittent operation (Trigger ﬁ ring)

1) Set the switching device to FULL SEQUENTIAL

ACTUATION MECHANISM.

2) Pull the trigger rapidly and ﬁ rmly.

○ Continuous operation (Push lever ﬁ ring)

1) Do not press the nailer against the wood with

excessive force.

2) Separate the nailer from the wood as it recoils after

fastening.

17. Be careful of fasteners after driving them in.

The heads of the fasteners protrude from the surface of

the workpiece because they are duplex fasteners.

18. Do not drive fasteners into materials other than

wood.

If fasteners are driven into hard materials such as metal,

the fasteners can ricochet and hurt someone.

19. Take care when nailing thin boards or the corners

of wood.

When nailing thin boards, the nails may pass right

through, as may also be the case when nailing the

corners of wood due to deviation of the nails. In such

cases, always make sure that there is no one (and

nobody’s hands or feet; etc.) behind the thin board or

next to the wood you are going to nail.

20. Simultaneous nailing on both sides of the same

wall is dangerous.

Under no circumstances should nailing be performed on

both sides of a wall at the same time. This would be very

dangerous since the nails might pass through the wall

and thus cause injuries.

21. Do not use the power tool on scaﬀ oldings, ladders.

The power tool shall not be used for speciﬁ c application

for example:

– when changing one driving location to another

involves the use of scaﬀ oldings, stairs, ladders or

ladder alike constructions, e.g. roof laths,

– closing boxes or crates,

– ﬁ tting transportation safety systems e.g. on vehicles

and wagons

22. Remove all remaining fasteners and battery from

nailer when:

1) doing maintenance and inspection;

2) checking proper operation of push lever and trigger;

3) clearing a jam;

4) it is not in use;

5) leaving work area;

6) moving it to another location; and

7) handing it to another person.

Never attempt to clear a jam or repair the Nailer unless

you have removed battery and all remaining fasteners

from the Nailer.

The Nailer should never be left unattended since people

who are not familiar with the Nailer might handle it and

injure the themselves.

23. Remove battery from nailer when:

1) loading nails;

2) turning the adjuster.

24. The operating environment for this device is

between 0°C and 40°C so ensure use within this

temperature range. The device may fail to operate

below 0°C or above 40°C.

25. Always charge the battery at an ambient

temperature of 0–40°C.

A temperature of less than 0°C will result in over charging

which is dangerous. The battery cannot be charged at a

temperature greater than 40°C.

The most suitable temperature for charging is that of

20–25°C.

26. Do not use the charger continuously.

When one charging is completed, leave the charger for

about 15 minutes before the next charging of battery.

27. Do not allow foreign matter to enter the hole for

connecting the rechargeable battery.

28. Never disassemble the rechargeable battery or

charger.

29. Never short-circuit the rechargeable battery.

Short-circuiting the battery will cause a great electric

current and overheat. It results in burn or damage to the

battery.

30. Do not dispose of the battery in ﬁ re.

If the battery is burnt, it may explode.

31. Using an exhausted battery will damage the

charger.

32. Bring the battery to the shop from which it was

purchased as soon as the post-charging battery life

becomes too short for practical use.

Do not dispose of the exhausted battery.

33. Do not insert objects into the air ventilation slots of

the charger.

Inserting metal objects or ﬂ ammable into the charger air

ventilation slots will result in an electrical shock hazard or

damage to the charger.

34. NEVER allow magnets (or similar magnetic devices)

to be adjacent to the nailer, because the nailer has a

magnetic sensor inside.

Doing so will cause a failure or risk of injury by

malfunction.

35. Resting the unit after continuous work.

36. The power tool is equipped with a temperature

protection circuit to protect the motor. Continuous

work may cause the temperature of the unit to rise,

activating the temperature protection circuit and

automatically stopping operation. If this happens,

allow the power tool to cool before resuming use.

37. This product may cease to operate when an

abnormality is detected. In such cases, check

the items listed under “TROUBLESHOOTING” on

page 22.

38. Do not give a strong shock to the switch panel or

break it. It may lead to a trouble.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with the

protection function to stop the output.

In the cases of 1 to 3 described below, when using this

product, even if you are pulling the switch, the motor may

stop. This is not the trouble but the result of protection

function.

1. When the battery power remaining runs out, the motor

stops.

In such a case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this

case, release the switch of tool and eliminate causes of

overloading. After that, you can use it again.

12

English

3. If the battery is overheated under overload work, the

battery power may stop.

In this case, stop using the battery and let the battery

cool. After that, you can use it again.

Furthermore, please heed the following warning and caution.

WARNING

In order to prevent any battery leakage, heat generation,

smoke emission, explosion and ignition beforehand, please

be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on the

battery.

○ During work make sure that swarf and dust do not fall on

the battery.

○ Make sure that any swarf and dust falling on the power

tool during work do not collect on the battery.

○ Do not store an unused battery in a location exposed to

swarf and dust.

○ Before storing a battery, remove any swarf and dust that

may adhere to it and do not store it together with metal

parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such as a

nail, strike with a hammer, step on, throw or subject the

battery to severe physical shock.

3. Do not use an apparently damaged or deformed battery.

4. Do not use the battery in reverse polarity.

5. Do not connect directly to an electrical outlets or car

cigarette lighter sockets.

6. Do not use the battery for a purpose other than those

speciﬁ ed.

7. If the battery charging fails to complete even when a

speciﬁ ed recharging time has elapsed, immediately stop

further recharging.

8. Do not put or subject the battery to high temperatures or

high pressure such as into a microwave oven, dryer, or

high pressure container.

9. Keep away from ﬁ re immediately when leakage or foul

odor are detected.

10. Do not use in a location where strong static electricity

generates.

11. If there is battery leakage, foul odor, heat generated,

discolored or deformed, or in any way appears abnormal

during use, recharging or storage, immediately remove it

from the equipment or battery charger, and stop use.

12. Do not immerse the battery or allow any ﬂ uids to ﬂ ow

inside. Conductive liquid ingress, such as water, can

cause damage resulting in ﬁ re or explosion. Store your

battery in a cool, dry place, away from combustible and

ﬂ ammable items. Corrosive gas atmospheres must be

avoided.

CAUTION

1. If liquid leaking from the battery gets into your eyes,

do not rub your eyes and wash them well with fresh

clean water such as tap water and contact a doctor

immediately.

If left untreated, the liquid may cause eye-problems.

2. If liquid leaks onto your skin or clothes, wash well with

clean water such as tap water immediately.

There is a possibility that this can cause skin irritation.

3. If you ﬁ nd rust, foul odor, overheating, discolor,

deformation, and/or other irregularities when using the

battery for the ﬁ rst time, do not use and return it to your

supplier or vendor.

WARNING

If a conductive foreign matter enters in the terminal of lithium

ion battery, the battery may be shorted, causing ﬁ re. When

storing the lithium ion battery, obey surely the rules of

following contents.

○ Do not place conductive debris, nail and wires such as

iron wire and copper wire in the storage case.

○ To prevent shorting from occurring, load the battery in

the tool or insert securely the battery cover for storing

until the ventilator is not seen.

REGARDING LITHIUM-ION BATTERY

TRANSPORTATION

When transporting a lithium-ion battery, please observe the

following precautions.

WARNING

Notify the transporting company that a package contains a

lithium-ion battery, inform the company of its power output

and follow the instructions of the transportation company

when arranging transport.

○ Lithium-ion batteries that exceed a power output of

100 Wh are considered to be in the freight classiﬁ cation

of Dangerous Goods and will require special application

procedures.

○ For transportation abroad, you must comply with

international law and the rules and regulations of the

destination country.

Wh

Power Output

2 to 3 digit number

USB DEVICE CONNECTION

PRECAUTIONS (UC18YSL3)

When an unexpected problem occurs, the data in a USB

device connected to this product may be corrupted or lost.

Always make sure to back up any data contained in the USB

device prior to use with this product.

Please be aware that our company accepts absolutely no

responsibility for any data stored in a USB device that is

corrupted or lost, nor for any damage that may occur to a

connected device.

WARNING

○ Prior to use, check the connecting USB cable for any

defect or damage.

Using a defective or damaged USB cable can cause

smoke emission or ignition.

○ When the product is not being used, cover the USB port

with the rubber cover.

Buildup of dust etc. in the USB port can cause smoke

emission or ignition.

NOTE

○ There may be an occasional pause during USB

recharging.

○ When a USB device is not being charged, remove the

USB device from the charger.

Failure to do so may not only reduce the battery life

of a USB device, but may also result in unexpected

accidents.

○ It may not be possible to charge some USB devices,

depending on the type of device.

13

English

NAMES OF PARTS (Fig. 1–Fig. 26)

Top cover

Trigger

Firing head (outlet)

Push lever

Nail feeder (A)

Feeder knob

Magazine

Hook

Battery

Lock lever

Handle

Information indicator

Nailing operation switch

Power indicator

Power switch

Nailing operation indicator

Nails

Adjuster

Hook plate

Remaining battery indicator switch

Remaining battery indicator lamp

Display panel

SYMBOLS

WARNING

The following show symbols used for the machine.

Be sure that you understand their meaning before

use.

NR3675DD: Cordless Duplex Nailer

To reduce the risk of injury, user must read

instruction manual

Only for EU countries

Do not dispose of electric tools together with

household waste material!

In observance of European Directive

2012/19/EU on waste electrical and electronic

equipment and its implementation in

accordance with national law, electric tools

that have reached the end of their life must

be collected separately and returned to an

environmentally compatible recycling facility.

Direct current

ϨSwitching ON

Switching OFF

Disconnect the battery

Power switch

Power switch OFF

Power switch ON

Power indicator: Light in green

Nailing operation switch

FULL SEQUENTIAL ACTUATION

MECHANISM

FULL SEQUENTIAL ACTUATION

MECHANISM mode

Nailing operation indicator: Light in blue

CONTACT ACTUATION MECHANISM

CONTACT ACTUATION MECHANISM mode

Nailing operation indicator: Blink in blue

Trigger locked

Trigger unlocked

The battery remaining power is nearly empty.

Recharge the battery as soon as possible.

Information indicator:1 LED (Red) blink

Contact HiKOKI for inspection.

Information indicator: 2 LEDs blink in

Orange, after 10 seconds, automatically turn

oﬀ Power switch.

Shallow side

Deep side

Warning

Prohibited action

Battery

Lights ;

The battery remaining power is over 75%

Lights ;

The battery remaining power is 50%–75%.

Lights ;

The battery remaining power is 25%–50%.

Lights ;

The battery remaining power is less than 25%

Blinks ;

The battery remaining power is nearly empty.

Recharge the battery soonest possible.

Blinks ;

Output suspended due to high temperature.

Remove the battery from the tool and allow it to

fully cool down.

Blinks ;

Output suspended due to failure or malfunction.

The problem may be the battery so please

contact your dealer.

14

English

SPECIFICATIONS

1. Cordless Duplex Nailer

Model NR3675DD

Motor DC Brushless

Applicable Nail ø3.3 mm See Fig.

Applicable Nail Length 45 mm to 75 mm

Nail Loading capacity [nails] 35

Firing mode Full sequential / Contact (Selectable)

Cycle rate [nails/second] 2 (Intermittent)

Battery Model BSL36A18X

Type Li-ion battery

Voltage DC 36 V / 18 V

Weight* 4.9–5.2 kg

Dimension

Height × Length × Width 352 mm × 342 mm × 137 mm

* According to EPTA-Procedure 01/2014

Depending on attached battery. The heaviest weight is measured with BSL36B18X (sold separately).

2. Battery Charger

Model UC18YSL3

Charging voltage DC 14.4–18 V

Weight 0.6 kg

NOTE

Due to HiKOKI’s continuing program of research and development, the speciﬁ cations herein are subject to change

without prior notice.

15

English

NAIL SELECTION

WARNING

Be sure to use only the genuine HiKOKI nails for the NR3675DD. The use of any other nails can result in tool malfunction

and/or nail breakdown, leading to serious injuries.

Choose a suitable nail from Fig. Nails which are not shown in Fig. can not be driven with this tool.

The use of any other nails can result in tool malfunction and/or nail breakdown, leading to serious injuries.

NR3675DD

Plastic-collated strip nails

Duplex nails

21°

Min. Max.

3.3 mm

45 mm

5.2 mm

12.7 mm

5.9 mm

3.3 mm

75 mm

5.2 mm

12.7 mm

5.9 mm

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package contains the

accessories listed on page 2.

Standard accessories are subject to change without notice.

APPLICATIONS

○ Concrete form building.

CHARGING

Before using the power tool, charge the battery as follows.

1. Connect the charger’s power cord to the receptacle.

When connecting the plug of the charger to a receptacle,

the pilot lamp will blink in red (At 1- second intervals).

2. Insert the battery into the charger.

Firmly insert the battery into the charger as shown in

Fig. 3 (on page 3).

3. Charging

When inserting a battery in the charger, the charge

indicator lamp will blink in blue.

When the battery becomes fully recharged, the charge

indicator lamp will light up in green. (See Table 1)

(1) Charge indicator lamp indication

The indications of the charge indicator lamp will be as

shown in Table 1, according to the condition of the

charger or the rechargeable battery.

16

English

Table 1

Indications of the charge indicator lamp

Charge

indicator

lamp

(RED /

BLUE /

GREEN /

PURPLE)

Before

charging Blinks

(RED)

Lights for 0.5 seconds. Does not light for

0.5 seconds. (oﬀ for 0.5 seconds) Plugged into power source

While

charging

Blinks

(BLUE)

Lights for 0.5 seconds. Does not light for

1 second. (oﬀ for 1 second) Battery capacity at less than 50%

Blinks

(BLUE)

Lights for 1 second. Does not light

for 0.5 seconds. (oﬀ for 0.5 seconds) Battery capacity at less than 80%

Lights

(BLUE) Lights continuously Battery capacity at more than 80%

Charging

complete Lights

(GREEN)

Lights continuously

(Continuous buzzer sound: about

6 seconds)

Overheat

standby Blinks

(RED)

Lights for 0.3 seconds. Does not light for

0.3 seconds. (oﬀ for 0.3 seconds) Battery overheated. Unable to

charge. (Charging will commence

when battery cools)

Charging

impossible Flickers

(PURPLE)

Lights for 0.1 seconds. Does not light for

0.1 seconds. (oﬀ for 0.1 seconds)

(Intermittent buzzer sound: about

2 seconds)

Malfunction in the battery or the

charger

(2) Regarding the temperatures and charging time of the battery.

The temperatures and charging time will become as shown in Table 2.

Table 2

Charger UC18YSL3

Battery

Type of battery Li-ion

Temperatures at which the

battery can be recharged 0°C–50°C

Charging voltage V 14.4 18

Charging time,

approx. (At 20°C)

BSL14xx series BSL18xx series Multi volt

series

(4 cells) (8 cells) (5 cells) (10 cells) (10 cells)

min

BSL1415S

:

15

BSL1415

:

15

BSL1415X

:

15

BSL1420

:

20

BSL1425

:

25

BSL1430C

:

30

BSL1430

:

20

BSL1440

:

26

BSL1450

:

32

BSL1460

:

38

BSL1815S : 15

BSL1815 : 15

BSL1815X : 15

BSL1820 : 20

BSL1820M : 20

BSL1825 : 25

BSL1830C : 30

BSL1850C : 32

BSL1830 : 20

BSL1840 : 26

BSL1850 : 32

BSL1860 : 38

BSL36A18 : 32

BSL36A18X : 32

BSL36B18 : 52

BSL36B18X : 52

USB Charging voltage V 5

Charging current A 2

NOTE

The recharging time may vary according to the ambient

temperature and power source voltage.

4. Disconnect the charger’s power cord from the

receptacle.

5. Hold the charger ﬁ rmly and pull out the battery.

NOTE

Be sure to pull out the battery from the charger after use,

and then keep it.

Regarding electric discharge in case of new batteries,

etc.

As the internal chemical substance of new batteries and

batteries that have not been used for an extended period

is not activated, the electric discharge might be low when

using them the ﬁ rst and second time. This is a temporary

phenomenon, and normal time required for recharging

will be restored by recharging the batteries 2–3 times.

17

English

How to make the batteries perform longer.

(1) Recharge the batteries before they become completely

exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery. If

you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate, and

the battery life will be shortened. Leave the battery and

recharge it after it has cooled for a while.

CAUTION

○ If the battery is charged while it is heated because

it has been left for a long time in a location subject to

direct sunlight or because the battery has just been

used, the charge indicator lamp of the charger lights

for 0.3 seconds, does not light for 0.3 seconds (oﬀ for

0.3 seconds). In such a case, ﬁ rst let the battery cool,

then start charging.

○ When the charge indicator lamp ﬂ ickers (at 0.2-second

intervals), check for and take out any foreign objects in

the charger’s battery connector. If there are no foreign

objects, it is probable that the battery or charger is

malfunctioning. Take it to your authorized Service

Center.

○ Since the built-in micro computer takes about

3 seconds to conﬁ rm that the battery being charged with

UC18YSL3 is taken out, wait for a minimum of 3 seconds

before reinserting it to continue charging. If the battery

is reinserted within 3 seconds, the battery may not be

properly charged.

BEFORE USE

Action Figure Page

Removing and inserting the battery 2 3

Charging 3 3

Charging a USB device from a

electrical outlet 23-a 7

Charging a USB device and battery

from a electrical outlet 23-b 7

How to recharge USB device 24 7

When charging of USB device is

completed 25 7

Remaining battery indicator

(Battery: BSL36A18X) 26 7

Selecting accessories ―8

1. How to operate operation panel

(1) Power switch ON (See Fig. 4)

Under the condition of “Power switch OFF”, push and

hold on Power switch more than 1 second, then power

indicator lights in Green.

NOTE

Do not press the push lever and/or pull the trigger during

the process of turning the power switch ON.

Doing so will prevent the power switch from turning ON.

[Auto power oﬀ ]

When the power is turned on but the Nailer is not used

for 30 minutes, the Nailer is automatically turned oﬀ . To

turn on again, press the power switch.

WARNING

Never leave the Nailer with the power on. This could

result in an accident.

(2) Power switch OFF (See Fig. 4)

Under the condition of “Power switch ON”, push and

hold on Power switch more than 1 second, then power

indicator goes oﬀ .

Under the condition of “Power switch ON”, functions

below are active.

(3) Select Nailing operation mode

(Full sequential actuation / Contact actuation)

After power switch turn ON, always set in Full sequential

actuation mode as initial. (Nailing operation indicator

light in blue.) (See Fig. 5)

To change nailing operation mode, push Nailing

operation switch once. Every pushing, mode will change

between “Full sequential” and “Contact”. (See Fig. 6)

Lighting (Blue):

FULL SEQUENTIAL ACTUATION MECHANISM,

Blinking (Blue):

CONTACT ACTUATION MECHANISM

(4) Check Remaining battery level

The information indicator shows Remaining battery level

by status of LED lamp as below.

Status of indicator

1 LED (Red) blinks

The battery remaining

power is nearly empty.

Recharge the battery as

soon as possible.

(5) Information indicator

In case of operation error, LED lamps show as below.

Status of indicator

2 LEDs (Red) blink

2 LED lights blink in an

interval.

• In case of too hot

condition, Blink in

0.5 second interval.

• In case of too cold

condition, Blink in

0.25 second interval.

After 10 seconds, LED

lights and Power switch

automatically turn oﬀ .

Machine is in too cold

(below -5°C) or too hot

condition.

Allow the nailer to cool

or warm-up thoroughly in

adequate condition.

2 LEDs blink in Orange,

after about 10 seconds,

automatically turn oﬀ

Power switch.

Contact HiKOKI for

inspection.

18

English

2. Trigger Lock Mechanism (See Fig. 7)

WARNING

Make sure the trigger is locked when not ﬁ ring nails.

This Nailer has a lock mechanism to prevent the nails

from being ﬁ red.

Set the switch lock lever at the position to lock the

trigger.

Slide the switch lock lever to the position when the

Nailer is to be used, and to the position when it is not

in use.

3. Testing the nailer

WARNING

○ Make sure the trigger is locked when not ﬁ ring nails.

(See Fig. 7)

○ Never use Nailer unless push lever is operating properly.

The machine employs a preventive mechanism for

unloaded operation.

The machine enters a state where the push lever cannot

be pushed up. This takes place when the magazine is

not loaded with nails or when the remaining number of

nails becomes less than 6.

CAUTION

Use caution not to throw the push lever tip onto wood.

Before actually beginning the nailing work, test the Nailer by

using the checklist below. Conduct the tests in the following

order.

If abnormal operation occurs, stop using the Nailer and

contact a HiKOKI authorized service center immediately.

(1) REMOVE ALL NAILS AND BATTERY FROM NAILER.

□ ALL SCREWS MUST BE TIGHTENED.

□ THE PUSH LEVER AND TRIGGER MUST MOVE

SMOOTHLY with pulling back the feeder knob.

(2) Installing the battery.

Do not operate the push lever or trigger while installing

the battery. (See Fig. 2)

(3) Turn on the Power switch. (See Fig. 1)

Turn on the Power switch by push and hold on Power

switch more than 1 second.

Make sure the power indicator is lighting in green, and

nailing operation indicator is lighting in blue. (FULL

SEQUENTIAL ACTUATION MECHANISM)

NOTE

Do not press the push lever and/or pull the trigger during

the process of turning the power switch ON.

Doing so will prevent the power switch from turning ON.

[Auto power oﬀ ]

When the power is turned on but the Nailer is not used

for 30 minutes, the Nailer is automatically turned oﬀ . To

turn on again, press the power switch.

WARNING

Never leave the Nailer with the power on. This could

result in an accident.

Nailing operation indicator

Lighting (Blue):

FULL SEQUENTIAL ACTUATION MECHANISM,

Blinking (Blue):

CONTACT ACTUATION MECHANISM

Make sure the information indicator is not blinking.

If the information indicator is blinking in red, the battery

doesn’t have enough power and it needs to be charged.

(4) Remove the ﬁ nger from the trigger and press the push

lever against the workpiece with pulling back the feeder

knob.

□ THE NAILER MUST NOT OPERATE.

(5) Separate the push lever from the workpiece.

Next, point the nailer downward, with pulling back the

feeder knob, pull the trigger and then wait in that position

for 5 seconds or longer.

□ THE NAILER MUST NOT OPERATE.

(6) Without touching the trigger, depress the push lever

against the workpiece with pulling back the feeder

knob.

Next, pull the trigger.

□ THE NAILER MUST OPERATE.

Hold the trigger back and depress the push lever

against the workpiece again.

□ THE NAILER MUST NOT OPERATE.

Separate the ﬁ nger from the trigger.

Next,

is operated again.

□ THE NAILER MUST OPERATE.

(7) Separate the push lever from the workpiece, pull the

trigger.

Depress the push lever against the workpiece within

2 seconds.

□ THE NAILER MUST NOT OPERATE.

(8) Set the nailing operation indicator blinking ON mode.

(CONTACT ACTUATION MECHANISM)

Push the nailing operation switch once, make sure that

the indicator is blinking Blue.

Separate the push lever from the workpiece, pull the

trigger.

Depress the push lever against the workpiece within

2 seconds.

□ THE NAILER MUST OPERATE.

(9) If no abnormal operation is observed, you may load nails

in the Nailer.

Drive nails into the workpiece that is the same type to be

used in the actual application.

□ THE NAILER MUST OPERATE PROPERLY.

4. Checking push lever operations

WARNING

Make sure the trigger is locked when not ﬁ ring nails.

Always make sure the trigger is locked and the battery

removed from the power tool when checking push lever

operations.

Check to make sure the push lever slides smoothly when

operated.

Clean the sliding area on the push lever if it doesn’t slide

smoothly.

5. Load nails

WARNING

When loading nails into Nailer,

1) remove battery from the nailer;

2) do not pull trigger;

3) do not depress push lever; and

4) keep nailer pointed downward.

2–Action Nail Feeding!

(1) Insert nail strip into the back of the magazine. (See

Fig. 8)

(2) Slide the nail strip forward in the magazine. (See Fig. 9)

19

English

(3) Pull the nail feeder (A) back to engage the feeder knob to

the nail strip. (See Fig. 10)

NOTE

○ Quietly push the nail feeder (A) and feeder knob against

the nail.

If the nail feeder (A) and feeder knob are released from

backward the magazine and bumped against the nail,

the connecting plastic of the nail can be damaged.

○ Use nail strip of more than 8 nails.

○ Use an unbroken nail strip with nails of all the same

length.

The Nailer is now ready to operate.

Removing the nails:

Pull the feeder knob backward. (See Fig. 11)

Return the feeder knob forward quietly while pushing the

nail feeder (A).

Pull out nails from the back of the magazine. (See

Fig. 12)

HOW TO USE THE NAILER

WARNING

○ NEVER point tool at yourself or others in work area.

○ Keep ﬁ ngers AWAY from trigger when not driving nails to

avoid accidental ﬁ ring.

○ Do not use the electrical cord if damaged. Have it

repaired immediately.

○ Choice of triggering method is important.

Please read and understand “1. Nailing procedures”

found below.

○ Before starting work, check the nailing operation

switching device.

This HiKOKI nailer includes a nailing operation switching

device.

Before starting work, make sure that the switching

device is properly set.

If the switching device is not set properly, the nailer will

not operate correctly.

○ Never place your face, hands or feet near ﬁ ring head

when using.

○ Do not drive nails on top of other nails or with Nailer at too

steep of an angle; nails can ricochet and hurt someone.

○ Do not drive nails into thin boards or near corners and

edges of workpiece. Nails can be driven through or away

from workpiece and hit someone.

○ Never drive nails from both sides of a wall at the same

time. Nails can be driven into and through the wall and

hit a person on the opposite side.

○ Never use Nailer which is defective or operating

abnormally.

○ Do not use Nailer as hammer.

○ Remove all remaining fasteners and battery from nailer

when:

1) doing maintenance and inspection;

2) checking proper operation of push lever and trigger;

3) cleaning a jam;

4) it is not in use;

5) leaving work area;

6) moving it to another location; and

7) handing it to another person.

○ Remove battery from Nailer when:

1) loading nails;

2) turning the adjuster.

This HiKOKI nailer is equipped with a nailer operation

switching device.

Use FULL SEQUENTIAL ACTUATION MECHANISM or

CONTACT ACTUATION MECHANISM in accordance with

the work to be performed.

Explanation of the various nailing operations

○ FULL SEQUENTIAL ACTUATION MECHANISM:

First, press the push lever against the wood; next, pull

the trigger to drive the nail.

Follow the same sequence to continue driving nails.

After nailing once, nailing will not be possible again until

remove ﬁ nger from the trigger and lift the tool oﬀ the

wood surface completely.

○ CONTACT ACTUATION MECHANISM:

CONTACT ACTUATION can follow two diﬀ erent

sequences, depending on your use.

To drive several nails:

1. Pull the trigger.

2. Press the push lever against the wood to drive the

nail.

3. If the trigger is held back, a nail will be driven each

time the push lever is pressed against the wood.

To drive a single nail:

1. Press the push lever against the wood.

2. Pull the trigger to drive the nail.

3. Remove your ﬁ nger from the trigger and remove the

nailer from the wood.

[Dry-ﬁ re lockout mechanism]

The machine employs a preventive mechanism for

unloaded operation.

The machine enters a state where the push lever cannot

be pushed up. This takes place when the magazine is

not loaded with nails or when the remaining number of

nails becomes less than 6.

CAUTION

Use caution not to throw the push lever tip onto wood

when the push lever cannot be pushed up.

1. Nailing procedures

This Nailer is equipped with the push lever and does not

operate unless the push lever is depressed.

There are two methods of operation to drive nails with

this Nailer.

They are:

1. Intermittent operation (Trigger ﬁ re):

2. Continuous operation (Push lever ﬁ re):

(1) Intermittent operation (Trigger ﬁ re)

Use the FULL SEQUENTIAL ACTUATION MECHANISM

setting. (See Fig. 13)

WARNING

○ For intermittent operation, Set the nailing operation switch

to FULL SEQUENTIAL ACTUATION MECHANISM

(Nailing operation indicator is light in blue.) (i.e. Set to

SINGLE ACTUATION MECHANISM.)

○ To avoid double ﬁ ring or accidental ﬁ ring due to recoil.

1) Set to FULL SEQUENTIAL ACTUATION

MECHANISM.

2) Pull the trigger rapidly and ﬁ rmly.

Set the nailing operation switch to FULL SEQUENTIAL

ACTUATION MECHANISM (Nailing operation indicator

is light in blue.)

(to set to FULL SEQUENTIAL ACTUATION

MECHANISM).

(Set the switching device to the nailing operation

indicator light in blue mode completely as shown in

the Fig. 13. Otherwise, it will be set to CONTACT

ACTUATION MECHANISM.)

Position the nail outlet on the workpiece with ﬁ nger oﬀ

the trigger.

Depress the push lever ﬁ rmly until it is completely

depressed.

Pull the trigger to drive a nail.

Remove ﬁ nger from the trigger and lift the tool oﬀ the

wood surface completely.

To continue nailing in a separate location, move the nailer

along the wood, repeating steps - as required.

NOTE

Operations

and should be done within 2 seconds

of each other. If more than 2 seconds pass after , the

Nailer will not work properly. If this happens, retry from

.

20

English

(2) Continuous operation (Push lever ﬁ re)

Using CONTACT ACTUATION MECHANISM (See

Fig. 14)

WARNING

To avoid double ﬁ ring or accidental ﬁ ring due to recoil.

1) Do not press the nailer against the wood with

excessive force.

2) Separate the nailer from the wood as it recoils after

nailing.

Set the nailing operation switch to CONTACT

ACTUATION MECHANISM (Nailing operation indicator

is blink in blue.)

(to set to CONTACT ACTUATION MECHANISM).

(Set the switching device to the nailing operation

indicator blink in blue completely as shown in the

Fig. 14. Otherwise, it will not operate properly.)

Pull the trigger with the Nailer oﬀ the workpiece.

Depress the push lever against the workpiece to drive a

nail.

Move the Nailer along the workpiece with a bouncing

motion.

Each depression of the push lever will drive a nail.

As soon as the desired number of nails have been driven,

remove ﬁ nger from the trigger.

NOTE

Operations

and should be done within 2 seconds

of each other. If more than 2 seconds pass after , the

Nailer will not work properly. If this happens, retry from

.

WARNING

○ Keep your ﬁ nger oﬀ the trigger except during nailing

operation, because serious injury could result if the push

lever accidentally contacts you or others in work area.

○ Keep hands and body away from the discharge area.

This HiKOKI nailer may bounce from the recoil of driving

a nail and unwanted subsequent nail may be driven,

possibly causing injury.

NOTE

○ If all warnings and instructions are followed, safe

operation is possible with all two systems: FULL

SEQUENTIAL ACTUATION MECHANISM, CONTACT

ACTUATION MECHANISM.

○ Always handle nails and package carefully. If nails are

dropped, collating bond may be broken, which will cause

mis-feeding and jamming.

○ After nailing:

1) remove battery from the Nailer;

2) remove all nails from the Nailer;

2. Adjusting the nailing depth

To assure that each nail penetrates to the same depth,

be sure that the Nailer is always held ﬁ rmly against the

workpiece.

If nails are driven too deep or shallow into the workpiece,

adjust the nailing in the following order.

Remove the battery from the Nailer. (See Fig. 15)

If nails are driven too deep, turn the adjuster to the

shallow side. (See Fig. 16)

Adjustments are in half-turn increments.

If nails are driven too shallow, turn the adjuster to the

deep side. (See Fig. 17)

Stop turning the adjuster when a suitable position is

reached for a nailing test.

Connect the battery to the Nailer.

ALWAYS WEAR SAFETY GLASSES.

Perform a nailing test.

Remove the battery from the Nailer.

Choose a suitable position for adjuster.

3. Using the hook (See Fig. 18, 19, 20)

WARNING

When using the hook, turn oﬀ the power switch (green

light “OFF”). Pay suﬃ cient attention so that the main

equipment does not fall.

If the tool falls, there is a risk of accident.

Hook can be installed on the left or right side.

Remove the battery, then remove all remaining nails

from the magazine.

Securely hold the main unit and remove the screw using

a screwdriver. (See Fig. 18)

Remove the hook and hook plate. (See Fig. 19)

Install the hook on the other side and securely fasten

with screw. (See Fig. 20)

NOTE

Hook can be used as a hanger.

4. Clearing a jam

If nails are jammed in ﬁ ring head, remove it, and adjust

the nailing in the following order.

CAUTION

Remove the battery from the Nailer.

Remove all nails.

Remove the M5 bolts with wrench. (See Fig. 21)

Pull magazine away from the ﬁ ring head, and clear jam.

(See Fig. 22)

CAUTION

○ NEVER hit the driver blade.

○ NEVER point the tool at yourself or another person, to

avoid risk of injury by mis-ﬁ ring.

Even if the battery is removed from the nailer, there is still

energy of compressed air remaining inside.

Attach the magazine to the injector and tighten with the

M5 bolt.

NOTE

In case of frequent jam, contact a HiKOKI authorized

service center.

MAINTENANCE AND INSPECTION

CAUTION

Be sure to remove all remaining fasteners and battery

from the nailer before maintenance and inspection.

1. Inspecting the magazine

Remove battery from the Nailer.

Clean the magazine. Remove dust and wooden

chips which may have accumulated in the magazine.

CAUTION

Check that the nail feeder slides smoothly by pulling it

with ﬁ nger.

If not smooth, nails can be driven at an irregular angle

and hurt someone.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Cleaning on the outside

When the power tool is stained, wipe with a soft dry cloth

or a cloth moistened with soapy water. Do not use chloric

solvents, gasoline or paint thinner, for they melt plastics.

5. Storage

Store the power tool and battery in a place in which the

temperature is less than 40°C and out of reach of children.

NOTE

Storing lithium-ion batteries.

Make sure the lithium-ion batteries have been fully

charged before storing them.

Prolonged storage (3 months or more) of batteries with

a low charge may result in performance deterioration,

signiﬁ cantly reducing battery usage time or rendering

the batteries incapable of holding a charge.

However, signiﬁ cantly reduced battery usage time may

be recovered by repeatedly charging and using the

batteries two to ﬁ ve times.

La page charge ...

Hikoki NR3675DD Manuel utilisateur

Hikoki NR3675DD Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents