Hikoki NR3675DD Manuel utilisateur

Catégorie
Outils électroportatifs
Taper
Manuel utilisateur
Handling instructions
Bedienungsanleitung
Mode d’emploi
Istruzioni per l’uso
Gebruiksaanwijzing
Instrucciones de manejo
Instruções de uso
Bruksanvisning
Brugsanvisning
Bruksanvisning
Käyttöohjeet
en
de
fr
it
nl
es
pt
sv
da
no
NR 3675DD
en
de
fr
it
nl
es
pt
sv
da
no
2
NR3675DD
(NNP) (2XCZ)
BSL36A18X
22
UC18YSL3
11
11
111
111
111
111
3
1
2
34
<UC18YSL3>
4
56
78
910
5
11 12
13 14
15 16
6
17 18
19 20
21
7
22
23 24
ab
25 26
8
337528
BSL36..18..
UC18YSL3 (14,4 V18 V)
329897
9
English
power source and/or battery pack, picking up or
carrying the tool.
Carrying power tools with your nger on the switch
or energising power tools that have the switch on
invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left attached to a rotating part of
the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times.
This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts.
Loose clothes, jewellery or long hair can be caught in
moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application.
The correct power tool will do the job better and safer
at the rate for which it was designed.
b) Do not use the power tool if the switch does not
turn it on and o .
Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/
or the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may a ect the
power toolʼs operation.
If damaged, have the power tool repaired before
use.
Many accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed.
Use of the power tool for operations di erent from
those intended could result in a hazardous situation.
5) Battery tool use and care
a) Recharge only with the charger speci ed by the
manufacturer.
A charger that is suitable for one type of battery pack
may create a risk of re when used with another
battery pack.
b) Use power tools only with speci cally
designated battery packs.
Use of any other battery packs may create a risk of
injury and re.
GENERAL POWER TOOL SAFETY
WARNINGS
WARNING
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in
electric shock, re and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
ammable liquids, gases or dust.
Power tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed
(grounded) power tools.
Unmodi ed plugs and matching outlets will reduce
risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts.
Damaged or entangled cords increase the risk of
electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the
risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the in uence of drugs, alcohol or
medication.
A moment of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment. Always
wear eye protection.
Protective equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the o position before connecting to
(Original instructions)
10
English
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another.
Shorting the battery terminals together may cause
burns or a re.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, ush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or
burns.
6) Service
a) Have your power tool serviced by a quali ed
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
PRECAUTION
Keep children and in rm persons away.
When not in use, tools should be stored out of reach of
children and in rm persons.
CORDLESS DUPLEX NAILER SAFETY
WARNINGS
1. Always assume that the tool contains fasteners.
Careless handling of the nailer can result in unexpected
ring of fasteners and personal injury.
2. Do not point the tool towards yourself or anyone
nearby.
Unexpected triggering will discharge the fastener
causing an injury.
3. Do not actuate the tool unless the tool is placed
rmly against the workpiece.
If the tool is not contact with the workpiece, the fastener
may be de ected away from your target.
4. Disconnect the tool from the power source when
the fastener jams in the tool.
While removing a jammed fastener, the nailer may be
accidentally activated if it is plugged in.
5. Use caution while removing a jammed fastener.
The mechanism may be under compression and the
fastener may be forcefully discharged while attempting
to free a jammed condition.
6. Do not use this nailer for fastening electrical cables.
It is not designed for electric cable installation and may
damage the insulation of electric cables thereby causing
electric shock or re hazards.
ADDITIONAL SAFETY WARNINGS
1. Safe operation through correct usage.
This tool was designed for driving nails into wood and
similar materials. Use it for its intended purpose only.
2. Be careful of ignition and explosions.
Since sparks may y during nailing, it is dangerous to use
this tool near lacquer, paint, benzine, thinner, gasoline,
gas, adhesives and similar in ammable substances as
they may ignite or explode. Under no circumstances
should this tool therefore be used in the vicinity of such
in ammable material.
3. Always wear eye protection (protective goggles).
When operating the power tool, always
wear eye protection, and ensure that
surrounding people wear eye protection
too.
The possibility of fragments of the nails that were not
properly hit entering the eye is a threat to sight. Eye
protection can be bought at any hardware store. Always
wear eye protection while operating this tool. Use either
eye protection or a wide vision mask over prescription
glasses.
Employers should always enforce the use of eye
protection equipment.
4. Protect your ears and head.
When engaged in nailing work please wear ear mu ers
and head protection. Also, depending on condition,
ensure that surrounding people also wear ear mu ers
and head protection.
5. Pay attention to those working close to you.
It would be very dangerous if nails that were not properly
driven in should hit other people. Therefore, always pay
attention to the safety of the people around you when
using this tool. Always make sure that nobody’s body,
hands or feet are close to the nail outlet.
6. Never point the nail outlet towards people.
Always assume the tool contains
fasteners.
If the nail outlet is pointed towards people,
serious accidents may be caused if you
mistakenly discharge the tool.
When connecting and disconnecting the battery, during
nail loading or similar operations, be sure the nail outlet
is not pointed towards anyone (including yourself).
Even when no nails are loaded at all, it is dangerous to
discharge the tool while pointing it at someone, so never
attempt to do so. No horseplay. Respect the tool as a
working implement.
7. Check push lever before use.
Make sure the push lever operates properly. (The push
lever may be called “Safety”.) Never use the Nailer
unless the push lever is operating properly, otherwise
the Nailer could drive a fastener unexpectedly. Do not
tamper with or remove the push lever, otherwise the
push lever becomes inoperable.
8. Choice of triggering method is important.
Read and understand section titled “HOW TO USE THE
NAILER” on page 19.
9. Prior to using this product, make sure that it is
operating properly in accordance with the content
of “Testing the nailer” on page 18.
10. Use speci ed nails only.
Never use nails other than those speci ed and described
in these instructions.
11. Be careful when connecting the battery.
When connecting the battery and loading nails in
order not to re the tool by mistake, make sure of the
followings.
Do not touch the trigger.
Do not allow the ring head to contact with any
surface.
Keep the ring head down.
Strictly observe the above instructions, and always
make sure that no part of the body, hands or legs is
ever in front of the nail outlet.
12. Do not carelessly place your nger on the trigger.
Do not place your nger on the trigger except when
actually nailing. If you carry this tool or hand it to
someone while having your nger on the trigger, you may
inadvertently discharge a nail and thus cause an accident.
13. Press the nail outlet rmly against the material to
be nailed.
When driving in nails, press the nail outlet rmly against
the material to be nailed. If the outlet is not applied
properly, the nails may rebound.
11
English
14. Keep hands and feet away from the ring head
when using.
It is very dangerous for a nail to hit the
hands or feet by mistake.
15. Beware of the tool’s kickback.
Do not approach the top of the tool with your head etc.
during operation. This is dangerous because the tool
may recoil violently if the nail currently being driven in
comes into contact with a previous nail or a knot in the
wood.
16. Be careful of double re due to recoil.
If the push lever is unintentionally allowed to re-contact
the workpiece following recoil, an unwanted fastener will
be driven.
In order to avoid this undesirable double re,
Intermittent operation (Trigger ring)
1) Set the switching device to FULL SEQUENTIAL
ACTUATION MECHANISM.
2) Pull the trigger rapidly and rmly.
Continuous operation (Push lever ring)
1) Do not press the nailer against the wood with
excessive force.
2) Separate the nailer from the wood as it recoils after
fastening.
17. Be careful of fasteners after driving them in.
The heads of the fasteners protrude from the surface of
the workpiece because they are duplex fasteners.
18. Do not drive fasteners into materials other than
wood.
If fasteners are driven into hard materials such as metal,
the fasteners can ricochet and hurt someone.
19. Take care when nailing thin boards or the corners
of wood.
When nailing thin boards, the nails may pass right
through, as may also be the case when nailing the
corners of wood due to deviation of the nails. In such
cases, always make sure that there is no one (and
nobody’s hands or feet; etc.) behind the thin board or
next to the wood you are going to nail.
20. Simultaneous nailing on both sides of the same
wall is dangerous.
Under no circumstances should nailing be performed on
both sides of a wall at the same time. This would be very
dangerous since the nails might pass through the wall
and thus cause injuries.
21. Do not use the power tool on sca oldings, ladders.
The power tool shall not be used for speci c application
for example:
when changing one driving location to another
involves the use of sca oldings, stairs, ladders or
ladder alike constructions, e.g. roof laths,
closing boxes or crates,
tting transportation safety systems e.g. on vehicles
and wagons
22. Remove all remaining fasteners and battery from
nailer when:
1) doing maintenance and inspection;
2) checking proper operation of push lever and trigger;
3) clearing a jam;
4) it is not in use;
5) leaving work area;
6) moving it to another location; and
7) handing it to another person.
Never attempt to clear a jam or repair the Nailer unless
you have removed battery and all remaining fasteners
from the Nailer.
The Nailer should never be left unattended since people
who are not familiar with the Nailer might handle it and
injure the themselves.
23. Remove battery from nailer when:
1) loading nails;
2) turning the adjuster.
24. The operating environment for this device is
between 0°C and 40°C so ensure use within this
temperature range. The device may fail to operate
below 0°C or above 40°C.
25. Always charge the battery at an ambient
temperature of 0–40°C.
A temperature of less than 0°C will result in over charging
which is dangerous. The battery cannot be charged at a
temperature greater than 40°C.
The most suitable temperature for charging is that of
20–25°C.
26. Do not use the charger continuously.
When one charging is completed, leave the charger for
about 15 minutes before the next charging of battery.
27. Do not allow foreign matter to enter the hole for
connecting the rechargeable battery.
28. Never disassemble the rechargeable battery or
charger.
29. Never short-circuit the rechargeable battery.
Short-circuiting the battery will cause a great electric
current and overheat. It results in burn or damage to the
battery.
30. Do not dispose of the battery in re.
If the battery is burnt, it may explode.
31. Using an exhausted battery will damage the
charger.
32. Bring the battery to the shop from which it was
purchased as soon as the post-charging battery life
becomes too short for practical use.
Do not dispose of the exhausted battery.
33. Do not insert objects into the air ventilation slots of
the charger.
Inserting metal objects or ammable into the charger air
ventilation slots will result in an electrical shock hazard or
damage to the charger.
34. NEVER allow magnets (or similar magnetic devices)
to be adjacent to the nailer, because the nailer has a
magnetic sensor inside.
Doing so will cause a failure or risk of injury by
malfunction.
35. Resting the unit after continuous work.
36. The power tool is equipped with a temperature
protection circuit to protect the motor. Continuous
work may cause the temperature of the unit to rise,
activating the temperature protection circuit and
automatically stopping operation. If this happens,
allow the power tool to cool before resuming use.
37. This product may cease to operate when an
abnormality is detected. In such cases, check
the items listed under “TROUBLESHOOTING” on
page 22.
38. Do not give a strong shock to the switch panel or
break it. It may lead to a trouble.
CAUTION ON LITHIUM-ION BATTERY
To extend the lifetime, the lithium-ion battery equips with the
protection function to stop the output.
In the cases of 1 to 3 described below, when using this
product, even if you are pulling the switch, the motor may
stop. This is not the trouble but the result of protection
function.
1. When the battery power remaining runs out, the motor
stops.
In such a case, charge it up immediately.
2. If the tool is overloaded, the motor may stop. In this
case, release the switch of tool and eliminate causes of
overloading. After that, you can use it again.
12
English
3. If the battery is overheated under overload work, the
battery power may stop.
In this case, stop using the battery and let the battery
cool. After that, you can use it again.
Furthermore, please heed the following warning and caution.
WARNING
In order to prevent any battery leakage, heat generation,
smoke emission, explosion and ignition beforehand, please
be sure to heed the following precautions.
1. Make sure that swarf and dust do not collect on the
battery.
During work make sure that swarf and dust do not fall on
the battery.
Make sure that any swarf and dust falling on the power
tool during work do not collect on the battery.
Do not store an unused battery in a location exposed to
swarf and dust.
Before storing a battery, remove any swarf and dust that
may adhere to it and do not store it together with metal
parts (screws, nails, etc.).
2. Do not pierce battery with a sharp object such as a
nail, strike with a hammer, step on, throw or subject the
battery to severe physical shock.
3. Do not use an apparently damaged or deformed battery.
4. Do not use the battery in reverse polarity.
5. Do not connect directly to an electrical outlets or car
cigarette lighter sockets.
6. Do not use the battery for a purpose other than those
speci ed.
7. If the battery charging fails to complete even when a
speci ed recharging time has elapsed, immediately stop
further recharging.
8. Do not put or subject the battery to high temperatures or
high pressure such as into a microwave oven, dryer, or
high pressure container.
9. Keep away from re immediately when leakage or foul
odor are detected.
10. Do not use in a location where strong static electricity
generates.
11. If there is battery leakage, foul odor, heat generated,
discolored or deformed, or in any way appears abnormal
during use, recharging or storage, immediately remove it
from the equipment or battery charger, and stop use.
12. Do not immerse the battery or allow any uids to ow
inside. Conductive liquid ingress, such as water, can
cause damage resulting in re or explosion. Store your
battery in a cool, dry place, away from combustible and
ammable items. Corrosive gas atmospheres must be
avoided.
CAUTION
1. If liquid leaking from the battery gets into your eyes,
do not rub your eyes and wash them well with fresh
clean water such as tap water and contact a doctor
immediately.
If left untreated, the liquid may cause eye-problems.
2. If liquid leaks onto your skin or clothes, wash well with
clean water such as tap water immediately.
There is a possibility that this can cause skin irritation.
3. If you nd rust, foul odor, overheating, discolor,
deformation, and/or other irregularities when using the
battery for the rst time, do not use and return it to your
supplier or vendor.
WARNING
If a conductive foreign matter enters in the terminal of lithium
ion battery, the battery may be shorted, causing re. When
storing the lithium ion battery, obey surely the rules of
following contents.
Do not place conductive debris, nail and wires such as
iron wire and copper wire in the storage case.
To prevent shorting from occurring, load the battery in
the tool or insert securely the battery cover for storing
until the ventilator is not seen.
REGARDING LITHIUM-ION BATTERY
TRANSPORTATION
When transporting a lithium-ion battery, please observe the
following precautions.
WARNING
Notify the transporting company that a package contains a
lithium-ion battery, inform the company of its power output
and follow the instructions of the transportation company
when arranging transport.
Lithium-ion batteries that exceed a power output of
100 Wh are considered to be in the freight classi cation
of Dangerous Goods and will require special application
procedures.
For transportation abroad, you must comply with
international law and the rules and regulations of the
destination country.
Wh
Power Output
2 to 3 digit number
USB DEVICE CONNECTION
PRECAUTIONS (UC18YSL3)
When an unexpected problem occurs, the data in a USB
device connected to this product may be corrupted or lost.
Always make sure to back up any data contained in the USB
device prior to use with this product.
Please be aware that our company accepts absolutely no
responsibility for any data stored in a USB device that is
corrupted or lost, nor for any damage that may occur to a
connected device.
WARNING
Prior to use, check the connecting USB cable for any
defect or damage.
Using a defective or damaged USB cable can cause
smoke emission or ignition.
When the product is not being used, cover the USB port
with the rubber cover.
Buildup of dust etc. in the USB port can cause smoke
emission or ignition.
NOTE
There may be an occasional pause during USB
recharging.
When a USB device is not being charged, remove the
USB device from the charger.
Failure to do so may not only reduce the battery life
of a USB device, but may also result in unexpected
accidents.
It may not be possible to charge some USB devices,
depending on the type of device.
13
English
NAMES OF PARTS (Fig. 1Fig. 26)
Top cover
Trigger
Firing head (outlet)
Push lever
Nail feeder (A)
Feeder knob
Magazine
Hook
Battery
Lock lever
Handle
Information indicator
Nailing operation switch
Power indicator
Power switch
Nailing operation indicator
Nails
Adjuster
Hook plate
Remaining battery indicator switch
Remaining battery indicator lamp
Display panel
SYMBOLS
WARNING
The following show symbols used for the machine.
Be sure that you understand their meaning before
use.
NR3675DD: Cordless Duplex Nailer
To reduce the risk of injury, user must read
instruction manual
Only for EU countries
Do not dispose of electric tools together with
household waste material!
In observance of European Directive
2012/19/EU on waste electrical and electronic
equipment and its implementation in
accordance with national law, electric tools
that have reached the end of their life must
be collected separately and returned to an
environmentally compatible recycling facility.
Direct current
ϨSwitching ON
Switching OFF
Disconnect the battery
Power switch
Power switch OFF
Power switch ON
Power indicator: Light in green
Nailing operation switch
FULL SEQUENTIAL ACTUATION
MECHANISM
FULL SEQUENTIAL ACTUATION
MECHANISM mode
Nailing operation indicator: Light in blue
CONTACT ACTUATION MECHANISM
CONTACT ACTUATION MECHANISM mode
Nailing operation indicator: Blink in blue
Trigger locked
Trigger unlocked
The battery remaining power is nearly empty.
Recharge the battery as soon as possible.
Information indicator:1 LED (Red) blink
Contact HiKOKI for inspection.
Information indicator: 2 LEDs blink in
Orange, after 10 seconds, automatically turn
o Power switch.
Shallow side
Deep side
Warning
Prohibited action
Battery
Lights ;
The battery remaining power is over 75%
Lights ;
The battery remaining power is 50%–75%.
Lights ;
The battery remaining power is 25%–50%.
Lights ;
The battery remaining power is less than 25%
Blinks ;
The battery remaining power is nearly empty.
Recharge the battery soonest possible.
Blinks ;
Output suspended due to high temperature.
Remove the battery from the tool and allow it to
fully cool down.
Blinks ;
Output suspended due to failure or malfunction.
The problem may be the battery so please
contact your dealer.
14
English
SPECIFICATIONS
1. Cordless Duplex Nailer
Model NR3675DD
Motor DC Brushless
Applicable Nail ø3.3 mm See Fig.
Applicable Nail Length 45 mm to 75 mm
Nail Loading capacity [nails] 35
Firing mode Full sequential / Contact (Selectable)
Cycle rate [nails/second] 2 (Intermittent)
Battery Model BSL36A18X
Type Li-ion battery
Voltage DC 36 V / 18 V
Weight* 4.9–5.2 kg
Dimension
Height × Length × Width 352 mm × 342 mm × 137 mm
* According to EPTA-Procedure 01/2014
Depending on attached battery. The heaviest weight is measured with BSL36B18X (sold separately).
2. Battery Charger
Model UC18YSL3
Charging voltage DC 14.4–18 V
Weight 0.6 kg
NOTE
Due to HiKOKI’s continuing program of research and development, the speci cations herein are subject to change
without prior notice.
15
English
NAIL SELECTION
WARNING
Be sure to use only the genuine HiKOKI nails for the NR3675DD. The use of any other nails can result in tool malfunction
and/or nail breakdown, leading to serious injuries.
Choose a suitable nail from Fig. Nails which are not shown in Fig. can not be driven with this tool.
The use of any other nails can result in tool malfunction and/or nail breakdown, leading to serious injuries.
NR3675DD
Plastic-collated strip nails
Duplex nails
21°
Min. Max.
3.3 mm
45 mm
5.2 mm
12.7 mm
5.9 mm
3.3 mm
75 mm
5.2 mm
12.7 mm
5.9 mm
STANDARD ACCESSORIES
In addition to the main unit (1 unit), the package contains the
accessories listed on page 2.
Standard accessories are subject to change without notice.
APPLICATIONS
Concrete form building.
CHARGING
Before using the power tool, charge the battery as follows.
1. Connect the charger’s power cord to the receptacle.
When connecting the plug of the charger to a receptacle,
the pilot lamp will blink in red (At 1- second intervals).
2. Insert the battery into the charger.
Firmly insert the battery into the charger as shown in
Fig. 3 (on page 3).
3. Charging
When inserting a battery in the charger, the charge
indicator lamp will blink in blue.
When the battery becomes fully recharged, the charge
indicator lamp will light up in green. (See Table 1)
(1) Charge indicator lamp indication
The indications of the charge indicator lamp will be as
shown in Table 1, according to the condition of the
charger or the rechargeable battery.
16
English
Table 1
Indications of the charge indicator lamp
Charge
indicator
lamp
(RED /
BLUE /
GREEN /
PURPLE)
Before
charging Blinks
(RED)
Lights for 0.5 seconds. Does not light for
0.5 seconds. (o for 0.5 seconds) Plugged into power source
While
charging
Blinks
(BLUE)
Lights for 0.5 seconds. Does not light for
1 second. (o for 1 second) Battery capacity at less than 50%
Blinks
(BLUE)
Lights for 1 second. Does not light
for 0.5 seconds. (o for 0.5 seconds) Battery capacity at less than 80%
Lights
(BLUE) Lights continuously Battery capacity at more than 80%
Charging
complete Lights
(GREEN)
Lights continuously
(Continuous buzzer sound: about
6 seconds)
Overheat
standby Blinks
(RED)
Lights for 0.3 seconds. Does not light for
0.3 seconds. (o for 0.3 seconds) Battery overheated. Unable to
charge. (Charging will commence
when battery cools)
Charging
impossible Flickers
(PURPLE)
Lights for 0.1 seconds. Does not light for
0.1 seconds. (o for 0.1 seconds)
(Intermittent buzzer sound: about
2 seconds)
Malfunction in the battery or the
charger
(2) Regarding the temperatures and charging time of the battery.
The temperatures and charging time will become as shown in Table 2.
Table 2
Charger UC18YSL3
Battery
Type of battery Li-ion
Temperatures at which the
battery can be recharged 0°C–50°C
Charging voltage V 14.4 18
Charging time,
approx. (At 20°C)
BSL14xx series BSL18xx series Multi volt
series
(4 cells) (8 cells) (5 cells) (10 cells) (10 cells)
min
BSL1415S
:
15
BSL1415
:
15
BSL1415X
:
15
BSL1420
:
20
BSL1425
:
25
BSL1430C
:
30
BSL1430
:
20
BSL1440
:
26
BSL1450
:
32
BSL1460
:
38
BSL1815S : 15
BSL1815 : 15
BSL1815X : 15
BSL1820 : 20
BSL1820M : 20
BSL1825 : 25
BSL1830C : 30
BSL1850C : 32
BSL1830 : 20
BSL1840 : 26
BSL1850 : 32
BSL1860 : 38
BSL36A18 : 32
BSL36A18X : 32
BSL36B18 : 52
BSL36B18X : 52
USB Charging voltage V 5
Charging current A 2
NOTE
The recharging time may vary according to the ambient
temperature and power source voltage.
4. Disconnect the charger’s power cord from the
receptacle.
5. Hold the charger rmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after use,
and then keep it.
Regarding electric discharge in case of new batteries,
etc.
As the internal chemical substance of new batteries and
batteries that have not been used for an extended period
is not activated, the electric discharge might be low when
using them the rst and second time. This is a temporary
phenomenon, and normal time required for recharging
will be restored by recharging the batteries 2–3 times.
17
English
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery. If
you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate, and
the battery life will be shortened. Leave the battery and
recharge it after it has cooled for a while.
CAUTION
If the battery is charged while it is heated because
it has been left for a long time in a location subject to
direct sunlight or because the battery has just been
used, the charge indicator lamp of the charger lights
for 0.3 seconds, does not light for 0.3 seconds (o for
0.3 seconds). In such a case, rst let the battery cool,
then start charging.
When the charge indicator lamp ickers (at 0.2-second
intervals), check for and take out any foreign objects in
the charger’s battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service
Center.
Since the built-in micro computer takes about
3 seconds to con rm that the battery being charged with
UC18YSL3 is taken out, wait for a minimum of 3 seconds
before reinserting it to continue charging. If the battery
is reinserted within 3 seconds, the battery may not be
properly charged.
BEFORE USE
Action Figure Page
Removing and inserting the battery 2 3
Charging 3 3
Charging a USB device from a
electrical outlet 23-a 7
Charging a USB device and battery
from a electrical outlet 23-b 7
How to recharge USB device 24 7
When charging of USB device is
completed 25 7
Remaining battery indicator
(Battery: BSL36A18X) 26 7
Selecting accessories 8
1. How to operate operation panel
(1) Power switch ON (See Fig. 4)
Under the condition of “Power switch OFF”, push and
hold on Power switch more than 1 second, then power
indicator lights in Green.
NOTE
Do not press the push lever and/or pull the trigger during
the process of turning the power switch ON.
Doing so will prevent the power switch from turning ON.
[Auto power o ]
When the power is turned on but the Nailer is not used
for 30 minutes, the Nailer is automatically turned o . To
turn on again, press the power switch.
WARNING
Never leave the Nailer with the power on. This could
result in an accident.
(2) Power switch OFF (See Fig. 4)
Under the condition of “Power switch ON”, push and
hold on Power switch more than 1 second, then power
indicator goes o .
Under the condition of “Power switch ON”, functions
below are active.
(3) Select Nailing operation mode
(Full sequential actuation / Contact actuation)
After power switch turn ON, always set in Full sequential
actuation mode as initial. (Nailing operation indicator
light in blue.) (See Fig. 5)
To change nailing operation mode, push Nailing
operation switch once. Every pushing, mode will change
between “Full sequential” and “Contact”. (See Fig. 6)
Lighting (Blue):
FULL SEQUENTIAL ACTUATION MECHANISM,
Blinking (Blue):
CONTACT ACTUATION MECHANISM
(4) Check Remaining battery level
The information indicator shows Remaining battery level
by status of LED lamp as below.
Status of indicator
1 LED (Red) blinks
The battery remaining
power is nearly empty.
Recharge the battery as
soon as possible.
(5) Information indicator
In case of operation error, LED lamps show as below.
Status of indicator
2 LEDs (Red) blink
2 LED lights blink in an
interval.
In case of too hot
condition, Blink in
0.5 second interval.
In case of too cold
condition, Blink in
0.25 second interval.
After 10 seconds, LED
lights and Power switch
automatically turn o .
Machine is in too cold
(below -5°C) or too hot
condition.
Allow the nailer to cool
or warm-up thoroughly in
adequate condition.
2 LEDs blink in Orange,
after about 10 seconds,
automatically turn o
Power switch.
Contact HiKOKI for
inspection.
18
English
2. Trigger Lock Mechanism (See Fig. 7)
WARNING
Make sure the trigger is locked when not ring nails.
This Nailer has a lock mechanism to prevent the nails
from being red.
Set the switch lock lever at the position to lock the
trigger.
Slide the switch lock lever to the position when the
Nailer is to be used, and to the position when it is not
in use.
3. Testing the nailer
WARNING
Make sure the trigger is locked when not ring nails.
(See Fig. 7)
Never use Nailer unless push lever is operating properly.
The machine employs a preventive mechanism for
unloaded operation.
The machine enters a state where the push lever cannot
be pushed up. This takes place when the magazine is
not loaded with nails or when the remaining number of
nails becomes less than 6.
CAUTION
Use caution not to throw the push lever tip onto wood.
Before actually beginning the nailing work, test the Nailer by
using the checklist below. Conduct the tests in the following
order.
If abnormal operation occurs, stop using the Nailer and
contact a HiKOKI authorized service center immediately.
(1) REMOVE ALL NAILS AND BATTERY FROM NAILER.
ALL SCREWS MUST BE TIGHTENED.
THE PUSH LEVER AND TRIGGER MUST MOVE
SMOOTHLY with pulling back the feeder knob.
(2) Installing the battery.
Do not operate the push lever or trigger while installing
the battery. (See Fig. 2)
(3) Turn on the Power switch. (See Fig. 1)
Turn on the Power switch by push and hold on Power
switch more than 1 second.
Make sure the power indicator is lighting in green, and
nailing operation indicator is lighting in blue. (FULL
SEQUENTIAL ACTUATION MECHANISM)
NOTE
Do not press the push lever and/or pull the trigger during
the process of turning the power switch ON.
Doing so will prevent the power switch from turning ON.
[Auto power o ]
When the power is turned on but the Nailer is not used
for 30 minutes, the Nailer is automatically turned o . To
turn on again, press the power switch.
WARNING
Never leave the Nailer with the power on. This could
result in an accident.
Nailing operation indicator
Lighting (Blue):
FULL SEQUENTIAL ACTUATION MECHANISM,
Blinking (Blue):
CONTACT ACTUATION MECHANISM
Make sure the information indicator is not blinking.
If the information indicator is blinking in red, the battery
doesn’t have enough power and it needs to be charged.
(4) Remove the nger from the trigger and press the push
lever against the workpiece with pulling back the feeder
knob.
THE NAILER MUST NOT OPERATE.
(5) Separate the push lever from the workpiece.
Next, point the nailer downward, with pulling back the
feeder knob, pull the trigger and then wait in that position
for 5 seconds or longer.
THE NAILER MUST NOT OPERATE.
(6) Without touching the trigger, depress the push lever
against the workpiece with pulling back the feeder
knob.
Next, pull the trigger.
THE NAILER MUST OPERATE.
Hold the trigger back and depress the push lever
against the workpiece again.
THE NAILER MUST NOT OPERATE.
Separate the nger from the trigger.
Next,
is operated again.
THE NAILER MUST OPERATE.
(7) Separate the push lever from the workpiece, pull the
trigger.
Depress the push lever against the workpiece within
2 seconds.
THE NAILER MUST NOT OPERATE.
(8) Set the nailing operation indicator blinking ON mode.
(CONTACT ACTUATION MECHANISM)
Push the nailing operation switch once, make sure that
the indicator is blinking Blue.
Separate the push lever from the workpiece, pull the
trigger.
Depress the push lever against the workpiece within
2 seconds.
THE NAILER MUST OPERATE.
(9) If no abnormal operation is observed, you may load nails
in the Nailer.
Drive nails into the workpiece that is the same type to be
used in the actual application.
THE NAILER MUST OPERATE PROPERLY.
4. Checking push lever operations
WARNING
Make sure the trigger is locked when not ring nails.
Always make sure the trigger is locked and the battery
removed from the power tool when checking push lever
operations.
Check to make sure the push lever slides smoothly when
operated.
Clean the sliding area on the push lever if it doesn’t slide
smoothly.
5. Load nails
WARNING
When loading nails into Nailer,
1) remove battery from the nailer;
2) do not pull trigger;
3) do not depress push lever; and
4) keep nailer pointed downward.
2–Action Nail Feeding!
(1) Insert nail strip into the back of the magazine. (See
Fig. 8)
(2) Slide the nail strip forward in the magazine. (See Fig. 9)
19
English
(3) Pull the nail feeder (A) back to engage the feeder knob to
the nail strip. (See Fig. 10)
NOTE
Quietly push the nail feeder (A) and feeder knob against
the nail.
If the nail feeder (A) and feeder knob are released from
backward the magazine and bumped against the nail,
the connecting plastic of the nail can be damaged.
Use nail strip of more than 8 nails.
Use an unbroken nail strip with nails of all the same
length.
The Nailer is now ready to operate.
Removing the nails:
Pull the feeder knob backward. (See Fig. 11)
Return the feeder knob forward quietly while pushing the
nail feeder (A).
Pull out nails from the back of the magazine. (See
Fig. 12)
HOW TO USE THE NAILER
WARNING
NEVER point tool at yourself or others in work area.
Keep ngers AWAY from trigger when not driving nails to
avoid accidental ring.
Do not use the electrical cord if damaged. Have it
repaired immediately.
Choice of triggering method is important.
Please read and understand “1. Nailing procedures”
found below.
Before starting work, check the nailing operation
switching device.
This HiKOKI nailer includes a nailing operation switching
device.
Before starting work, make sure that the switching
device is properly set.
If the switching device is not set properly, the nailer will
not operate correctly.
Never place your face, hands or feet near ring head
when using.
Do not drive nails on top of other nails or with Nailer at too
steep of an angle; nails can ricochet and hurt someone.
Do not drive nails into thin boards or near corners and
edges of workpiece. Nails can be driven through or away
from workpiece and hit someone.
Never drive nails from both sides of a wall at the same
time. Nails can be driven into and through the wall and
hit a person on the opposite side.
Never use Nailer which is defective or operating
abnormally.
Do not use Nailer as hammer.
Remove all remaining fasteners and battery from nailer
when:
1) doing maintenance and inspection;
2) checking proper operation of push lever and trigger;
3) cleaning a jam;
4) it is not in use;
5) leaving work area;
6) moving it to another location; and
7) handing it to another person.
Remove battery from Nailer when:
1) loading nails;
2) turning the adjuster.
This HiKOKI nailer is equipped with a nailer operation
switching device.
Use FULL SEQUENTIAL ACTUATION MECHANISM or
CONTACT ACTUATION MECHANISM in accordance with
the work to be performed.
Explanation of the various nailing operations
FULL SEQUENTIAL ACTUATION MECHANISM:
First, press the push lever against the wood; next, pull
the trigger to drive the nail.
Follow the same sequence to continue driving nails.
After nailing once, nailing will not be possible again until
remove nger from the trigger and lift the tool o the
wood surface completely.
CONTACT ACTUATION MECHANISM:
CONTACT ACTUATION can follow two di erent
sequences, depending on your use.
To drive several nails:
1. Pull the trigger.
2. Press the push lever against the wood to drive the
nail.
3. If the trigger is held back, a nail will be driven each
time the push lever is pressed against the wood.
To drive a single nail:
1. Press the push lever against the wood.
2. Pull the trigger to drive the nail.
3. Remove your nger from the trigger and remove the
nailer from the wood.
[Dry- re lockout mechanism]
The machine employs a preventive mechanism for
unloaded operation.
The machine enters a state where the push lever cannot
be pushed up. This takes place when the magazine is
not loaded with nails or when the remaining number of
nails becomes less than 6.
CAUTION
Use caution not to throw the push lever tip onto wood
when the push lever cannot be pushed up.
1. Nailing procedures
This Nailer is equipped with the push lever and does not
operate unless the push lever is depressed.
There are two methods of operation to drive nails with
this Nailer.
They are:
1. Intermittent operation (Trigger re):
2. Continuous operation (Push lever re):
(1) Intermittent operation (Trigger re)
Use the FULL SEQUENTIAL ACTUATION MECHANISM
setting. (See Fig. 13)
WARNING
For intermittent operation, Set the nailing operation switch
to FULL SEQUENTIAL ACTUATION MECHANISM
(Nailing operation indicator is light in blue.) (i.e. Set to
SINGLE ACTUATION MECHANISM.)
To avoid double ring or accidental ring due to recoil.
1) Set to FULL SEQUENTIAL ACTUATION
MECHANISM.
2) Pull the trigger rapidly and rmly.
Set the nailing operation switch to FULL SEQUENTIAL
ACTUATION MECHANISM (Nailing operation indicator
is light in blue.)
(to set to FULL SEQUENTIAL ACTUATION
MECHANISM).
(Set the switching device to the nailing operation
indicator light in blue mode completely as shown in
the Fig. 13. Otherwise, it will be set to CONTACT
ACTUATION MECHANISM.)
Position the nail outlet on the workpiece with nger o
the trigger.
Depress the push lever rmly until it is completely
depressed.
Pull the trigger to drive a nail.
Remove nger from the trigger and lift the tool o the
wood surface completely.
To continue nailing in a separate location, move the nailer
along the wood, repeating steps - as required.
NOTE
Operations
and should be done within 2 seconds
of each other. If more than 2 seconds pass after , the
Nailer will not work properly. If this happens, retry from
.
20
English
(2) Continuous operation (Push lever re)
Using CONTACT ACTUATION MECHANISM (See
Fig. 14)
WARNING
To avoid double ring or accidental ring due to recoil.
1) Do not press the nailer against the wood with
excessive force.
2) Separate the nailer from the wood as it recoils after
nailing.
Set the nailing operation switch to CONTACT
ACTUATION MECHANISM (Nailing operation indicator
is blink in blue.)
(to set to CONTACT ACTUATION MECHANISM).
(Set the switching device to the nailing operation
indicator blink in blue completely as shown in the
Fig. 14. Otherwise, it will not operate properly.)
Pull the trigger with the Nailer o the workpiece.
Depress the push lever against the workpiece to drive a
nail.
Move the Nailer along the workpiece with a bouncing
motion.
Each depression of the push lever will drive a nail.
As soon as the desired number of nails have been driven,
remove nger from the trigger.
NOTE
Operations
and should be done within 2 seconds
of each other. If more than 2 seconds pass after , the
Nailer will not work properly. If this happens, retry from
.
WARNING
Keep your nger o the trigger except during nailing
operation, because serious injury could result if the push
lever accidentally contacts you or others in work area.
Keep hands and body away from the discharge area.
This HiKOKI nailer may bounce from the recoil of driving
a nail and unwanted subsequent nail may be driven,
possibly causing injury.
NOTE
If all warnings and instructions are followed, safe
operation is possible with all two systems: FULL
SEQUENTIAL ACTUATION MECHANISM, CONTACT
ACTUATION MECHANISM.
Always handle nails and package carefully. If nails are
dropped, collating bond may be broken, which will cause
mis-feeding and jamming.
After nailing:
1) remove battery from the Nailer;
2) remove all nails from the Nailer;
2. Adjusting the nailing depth
To assure that each nail penetrates to the same depth,
be sure that the Nailer is always held rmly against the
workpiece.
If nails are driven too deep or shallow into the workpiece,
adjust the nailing in the following order.
Remove the battery from the Nailer. (See Fig. 15)
If nails are driven too deep, turn the adjuster to the
shallow side. (See Fig. 16)
Adjustments are in half-turn increments.
If nails are driven too shallow, turn the adjuster to the
deep side. (See Fig. 17)
Stop turning the adjuster when a suitable position is
reached for a nailing test.
Connect the battery to the Nailer.
ALWAYS WEAR SAFETY GLASSES.
Perform a nailing test.
Remove the battery from the Nailer.
Choose a suitable position for adjuster.
3. Using the hook (See Fig. 18, 19, 20)
WARNING
When using the hook, turn o the power switch (green
light “OFF”). Pay su cient attention so that the main
equipment does not fall.
If the tool falls, there is a risk of accident.
Hook can be installed on the left or right side.
Remove the battery, then remove all remaining nails
from the magazine.
Securely hold the main unit and remove the screw using
a screwdriver. (See Fig. 18)
Remove the hook and hook plate. (See Fig. 19)
Install the hook on the other side and securely fasten
with screw. (See Fig. 20)
NOTE
Hook can be used as a hanger.
4. Clearing a jam
If nails are jammed in ring head, remove it, and adjust
the nailing in the following order.
CAUTION
Remove the battery from the Nailer.
Remove the battery from the Nailer.
Remove all nails.
Remove the M5 bolts with wrench. (See Fig. 21)
Pull magazine away from the ring head, and clear jam.
(See Fig. 22)
CAUTION
NEVER hit the driver blade.
NEVER point the tool at yourself or another person, to
avoid risk of injury by mis- ring.
Even if the battery is removed from the nailer, there is still
energy of compressed air remaining inside.
Attach the magazine to the injector and tighten with the
M5 bolt.
NOTE
In case of frequent jam, contact a HiKOKI authorized
service center.
MAINTENANCE AND INSPECTION
CAUTION
Be sure to remove all remaining fasteners and battery
from the nailer before maintenance and inspection.
1. Inspecting the magazine
Remove battery from the Nailer.
Clean the magazine. Remove dust and wooden
chips which may have accumulated in the magazine.
CAUTION
Check that the nail feeder slides smoothly by pulling it
with nger.
If not smooth, nails can be driven at an irregular angle
and hurt someone.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Cleaning on the outside
When the power tool is stained, wipe with a soft dry cloth
or a cloth moistened with soapy water. Do not use chloric
solvents, gasoline or paint thinner, for they melt plastics.
5. Storage
Store the power tool and battery in a place in which the
temperature is less than 40°C and out of reach of children.
NOTE
Storing lithium-ion batteries.
Make sure the lithium-ion batteries have been fully
charged before storing them.
Prolonged storage (3 months or more) of batteries with
a low charge may result in performance deterioration,
signi cantly reducing battery usage time or rendering
the batteries incapable of holding a charge.
However, signi cantly reduced battery usage time may
be recovered by repeatedly charging and using the
batteries two to ve times.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200

Hikoki NR3675DD Manuel utilisateur

Catégorie
Outils électroportatifs
Taper
Manuel utilisateur