2112
Fenton
Logistic
Park
Blvd.
Fenton,
MO
63026
USA
P/N
KIL00921505
FORM
NO.
K1505
ECO6-078-21
R11/21
Page
1
of
4
INSTALLATION, OPERATION &
MAINTENANCE DATA SHEET
KFLX/ARXC SERIES LED
LUMINAIRE
KFLX/ARXC SERIES LED LUMINAIRE
Luminaires are designed to be installed in Hazardous Locations: Class I, Division 2, Groups A, B, C and D; Class II,
Division 1, Groups E, F and G; Class III; T3C, T4, T4A, T5 or T6 (Class I, Div. 2); T3B, T3C (Class II, Div. 1); T3B, T3C
(Class I, Div 2 / Class II, Div. 1 Simultaneous Exposure); Type 4X; Marine Rated (US only); IP66. ); Ambient 40C, 55C
and 65C where applicable
IEC Zone 2. IEC 60079-0:2017 IEC 60079-7:2015 +A1: 2018 and IEC 60079-31:2015 Zone 2 type of protection Ex ec
(increased safety), Zone 21 type of protection Ex tb (dust).
STANDARD VERSION
EMERGENCY VERSION
II 3G Ex ec IIC T5/T4/T3* Gc
II 3G Ex ec IIC T5/T4* Gc
II 2D Ex tb IIIC T160°C/T135°C/T100°C * Db
II 2D Ex tb IIIC T135°C Db
-50°C<Tamb<+65°C < 120W
-20°C<Tamb<+50°C
-50°C<Tamb<+40°C/+55°C > 120W
*Depending on wattage and ambient temperature
IECEx certificate IECEx QPS 19.0031X.
ATEX certificate QPS21ATEX7002X (ec) QPS21ATEX5004X(tb).
CAUTION:
Before installing, make sure you are compliant with area classifications, failure to do so may result in bodily injury, death
and property damage. Do not attempt installation until you are familiar with the following procedures. All installation must
comply with the applicable Electrical Code.
Make sure that the circuit is de-energized before starting installation or maintenance.
Verify that the installation is grounded. Failure to ground will create electrical shock hazards, which can cause serious
injury and or death.
2112
Fenton
Logistic
Park
Blvd.
Fenton,
MO
63026
USA
P/N
KIL00921505
FORM
NO.
K1505
ECO6-078-21
R11/21
Page
2
of
4
Note: Due to the surge protection provided in the fixture to protect the internal electronics and LEDs, a branch
circuit with
the LED fixture may false fail a megohmmeter test (sometimes referred to as a megger test). If a
megohmmeter test is
required, the LED fixture should be removed from the branch circuit.
This fitting’s driver is protected via thermal foldback sensor which reduces the light output of the fitting to prolong the life of
the driver in high ambient service conditions. When the driver reaches temperatures near the manufacturer’s recommended
limits, the foldback sensor will activate and slightly reduce the light output to decrease the temperature of the fixture. Once
the driver temperature reduces from this level, the fitting will operate at normal levels
Note: Multiple fluorescent or LED fixtures attached to a single Ground Fault Circuit Interrupter (GFCI) may cause
nuisance
tripping of the GFCI. Regulatory agencies allow a small amount of leakage current because of the circuitry
required to mitigate
possible issues with electromagnetic compatibility (reference UL8750 and EN61347). The
summation of these leakage
currents from multiple fixtures may be enough to trip a GFCI.
Note: When fitted with a polycarbonate lens, the polycarbonate lens should not be subjected to sunlight.
NOTE- For Class I, Division 1 / Class II, Division 1 / Class I, Zone 1 Hazardous Locations, use rigid conduit
or
appropriate cable connectors/ glands rated for Class I, Division 1 Groups BCD
NOTE – Pour les endroits dangereux Classe I, Division 1 / Classe II, Division 1 / Classe I, Zone 1 utiliser des Conduits rigides.
KFLX/ARXC INSTALLATION INSTRUCTIONS:
Yoke Mounting:
1.
For convenience, install the yoke bracket to the fixture before mounting the structure.
2.
Loosen bolts - aim the floodlight to the desired spot.
3.
Tighten both bolts securely.
4.
Fasten the yoke bracket to the mounting location using ½” bolts/fasteners.
5.
An “Earthquake Safety Chain” can be looped around the bosses that attach the LED heat sink to the driver box.
IMPORTANT NOTE:
Make sure that the circuit is de-energized at main fuse or at circuit breaker prior to installation.
NOTE IMPRORTANTE:
Mettre le circuit hors tension grace au fusible principal ou le disjoncteur. Open the fixture by loosening the swing bolts. Using the terminal
blocks supplied, run supply wire to fixture through applicable watertight joint
using sealing fittings at appropriate hole. The included hubs are for ¾”-
14NPT. A ½-14NPT reducer is also included. The holes through the cast
metal in the driver compartment are for an M20 cable gland. To use an M20
cable gland, discard the ¾ NPT hubs. he terminal block shown is with battery
back up. Non back up
fixtures will not have the “L2” terminal. Mains wiring
should be
brought into the corresponding marked terminal. Looping
wiring
can be accomplished by using the adjacent connection
port. A small
screwdriver can be inserted in the slot near the
connection port to ease the
force required to insert the wire. The external ground is located next to the
gland/hub opening
where the mains wires exit the fixture.
Reattach the swing bolts. Torque the cover bolts until the cover touches the housing. Approximately 3 N-m (25 in-lbf).
Re-
energized the circuit to verify the fixture is operating properly
IMPORTANT:
Technical information, advice and recommendations contained in these documents are based on information that Killark
believes to be reliable. All the information and advice contained in these documents is intended only for use by persons
having been trained and possessing the requisite skill and know-how and to be used by such persons only at their own
discretion and risk.
The nature of these instructions is informative only and do not cover all of the details, variations or combinations in which this
equipment may be used, its storage, delivery, installation, check out, safe operation, and maintenance. Since conditions of
use of the product are outside of the care, custody and control of Killark, the purchaser should determine the suitability of the
product for its intended use and assumes all risk and liability whatsoever in connection therewith. ATTENTION:
Avant d’installer le luminaire, s’assurer que le luminaire est conforme à la classification des zones, le non- respect de cette
règle risque d’entraîner des dommages corporels et / ou matériels. Ne pas tenter d’entreprendre l’installation avant d’être
familiarisé avec les procédures suivantes. Toute installation doit être conforme au code électrique local et / ou national et être
effectuée par un électricien qualifié.
Veiller à ce que le circuit soit mis hors tension avant de commencer l’installation ou la maintenance.
Vérifier si le luminaire est mis à la terre. S’il n’est pas mis à la terre il pourrait causer des risques de choc électrique
susceptibles d’entraîner des blessures graves ou la mort.
2112
Fenton
Logistic
Park
Blvd.
Fenton,
MO
63026
USA
P/N
KIL00921505
FORM
NO.
K1505
ECO6-078-21
R11/21
Page
3
of
4
BATTERY BACKUP FIXTURES
IMPORTANT: To turn the fixture completely off, an un-switched AC power
source of 120VAC to 277VAC is required for the Line Maintained (yellow)
and neutral (white) leads. A locally switched line must be attached to the
Line Switched (black) terminal. If the Line Switched terminal is attached to
continuous power, the fixture will go into battery backup mode if the power is
turned off.
IMPORTANT: Fixtures are shipped with a jumper between the Line
Maintained and Line Switched terminals. Remove the wire link (jumper) and
attach the Line Switched terminal to a local switched source when local
switching is required. The battery must be charged for at least 12 hours prior
to testing. The battery switch must be turned to the “ON” position for
the fixture to operate correctly. The fixture will not light up in battery
backup mode until AC power is supplied once while the battery switch
is in the “ON” position. Thereafter, the fixture will operate in battery
backup mode when the AC power is off.
SELF-DIAGNOSTIC INSTRUCTIONS/OPERATION: The self-diagnostic
feature is set from the factory. The emergency LED driver will conduct a
self-check for thirty (30) minutes every thirty (30) days; and ninety (90)
minutes or one hundred eighty (180) minutes self-check every 12 months.
After every self-check the LED indicator light will indicate a status signal.
Figure A Figure B
AIMING DESIGNATIONS
In environments with high dust, the dust will cover the lens and increase the temperature of the fixture. In a high dust
environment use the aiming diagram shown below as directed on the nameplate. The angle shown below will keep dust
from accumulating on the lens.
2112
Fenton
Logistic
Park
Blvd.
Fenton,
MO
63026
USA
P/N
KIL00921505
FORM
NO.
K1505
ECO6-078-21
R11/21
Page
4
of
4
Conditions for Safe Use:
1.
To prevent ignition of hazardous atmospheres, disconnect ballast/fixture from supply circuit before opening.
keep tightly
closed when in operation.
2.
Do not open, maintain or service in an area where an explosive atmosphere may be present.
3.
When Polycarbonate lens is in use, clean lens with damp cloth to avoid static discharge.
4.
The luminaire shall only be installed where there is a low risk of mechanical damage.
MAINTENANCE INSTRUCTIONS:
CAUTION:
Disconnect the supplying circuit before opening fixture or removing optics. To maintain maximum light output, this fixture
should be cleaned periodically. Maintenance procedures sometimes require fixtures to be hosed down for good
housekeeping. The supply circuit must be turned OFF and the fixture lens must be allowed to cool to the ambient room
temperature before cleaning. Only mild, non-abrasive cleaning agents should be used. The force of water applied by a
hose must not exceed 65 gallons per minute coming from a 1” diameter hose applied at a distance of 10 feet.
HIGH VIBRATION AREAS:
Periodic inspection of fastener tightness is required; recommended every six (6) months.
REMEMBER TO SAVE ONE OF THESE SHEETS FOR MAINTENANCE PERSONNEL
Technical
information,
advice
and
recommendations
contained
in
these
documents
are
based
on
information
that
Killark
b elieves
to
be
reliable.
All
the
information
and
advice
contained
in
these
documents
is
intended
only
for
use
by
persons
having
been
trained
and
possessing
the
requisite
skill
and
know-how
an d
to
be
used
by
such
persons
only
at
their
own
discretion
and
risk.
The
nature
of
these
instructions
is
informative
only
and
do
not
cover
all
of
the
details,
variations
or
combinations
in
which
this
equipment
may
be
used,
its
storage,
delivery,
installation,
check
out,
safe
operation,
a nd
maintenance.
Since conditions
of
use
of
the
product
are
outside
of
the
care,
custody
and
control
of
Killark,
the
purchaser
should
determine
the suitability
of
the
product
for
its
intended
use,
and
assumes
all
risk
and
liability
whatsoever
in
connection
therewith.
Wire Guard Installation
Place
wire guard over lens area, placing loops over holes
behi
nd LED Housing. Attach guard to housing using two
screw
s provided through bosses in housing.
Both guard and reflector can be used on a fixture simu
ltaneously.
Dark Skies Reflector Installation
Place reflector over LED Housing. Hook tab on bottom of
reflector over boss going from Driver Housing to LED
Housing. Attach reflector to LED Housing using two screws
provided through bosses in LED Housing.
New fixtures with batteries can be stored for 2 years in a -20°C to 30°C ambient without a need of recharge. A
fully discharged unit should not be stored more than 6 months without being recharged. There is low voltage
disconnect of the battery to the emergency drivers, however as the batteries still have self-discharge they
should be recharged within 6 months to prevent the cells from permanent capacity loss. For long term
storage, turn the battery switch to the “off” position to prevent the cells from permanent capacity loss.
1. Make sure that the circuit is de-energized
2. Remove the housing cover.
3. Remove wires from lever nuts as necessary. To remove a wire from a lever nut, fully push up the lever and remove
the conductor.
4. Remove the two screws that hold the driver to the housing.
5. Remove the two screws that hold the battery compartment cover to the driver.
6. Disconnect the connector and replace the new battery (part number VM-BATT).
7. Reassemble
Battery Changing Procedure
-
1
-
2
-
3
-
4
KILLARK Arran X Zone 2 Guide d'installation
- Taper
- Guide d'installation
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
KILLARK LAL Guide d'installation
-
-
-
-
-
-