MICROCHIP WLR089U0 Regulatory Compliance Manuel utilisateur

WLR089U0 Regulatory Compliance
MICROCHIP
Marque
MICROCHIP
Modèle
WLR089U0 Regulatory Compliance
Taper
Manuel utilisateur
WLR089U0/WLR089UC
Regulatory Compliance Information
Revision 0.0
Jul’ 2020
1
Revision 0.0 (07/2020)
Preliminary
Revision 0.0 (07/2020)
Preliminary
This document covers the Regulatory Compliance information which
will be part of the WLR089U0/WLR089UC datasheet and related
documents shared with customers.
1.1 Antenna Considerations:
Table 1-1 provides the list of Approved antennas along with the manufacturer and part number details.
Part Number
Manufacturer
Antenna
Gain @
915 MHz
Band
Antenna
type
RFA-S1-C55H1-
150D034
ALEAD
technology
2.0dBi
half-wave
dipole
TH-89F-150mm-IPEX
BJTEK
NAVIGATION,INC
.
1.5dBi
half-wave
dipole
GWF-152XMPXX-H015
Joymax
Electronics Co.,
Ltd
2dBi
half-wave
dipole
GWF-152XRSXX-H015
Joymax
Electronics Co.,
Ltd
2dBi
half-wave
dipole
6610D13081-100
Kinsun
2dBi
half-wave
dipole
6610C03061
Kinsun
2dBi
half-wave
dipole
RFDPA131015IMBB301
PSA Walsin
technology
Corporation
0.90 dBi
half-wave
dipole
RFA-ZW-C55-B-RP-
D034
ALEAD
technology
2.0dBi
half-wave
dipole
Note:
2
Revision 0.0 (07/2020)
Preliminary
1) If the end-product using the Module is designed to have an antenna port that is accessible to the
end-user then a unique antenna connector (as permissible by FCC) must be used (e.g. RP (Reverse
Polarity)-SMA socket).
2) If an RF coaxial cable is used between the module RF output and the enclosure, then a unique
antenna connector must be used in the enclosure wall for interface with antenna.
1.2 WLR089U0/WLR089UC Usage Instructions under Modular Approval
For USA/Canada, the module has been certified for the modulation modes listed below. The user
must ensure that the module will only work on the 902-928 MHz frequency band and with one of the
modulation modes listed below, when used in USA and Canada.
• Operating Channels:
• 500kHz BW:
• 903MHz ~ 927.5MHz
o 8 Uplink Channels, Channel Spacing 1.6MHz
o 8 Downlink Channels, Channel Spacing 0.6MHz
• 125kHz BW:
o 902.3MHz ~ 927.5MHz
▪ 64 Channels, Channel Spacing 200kHz
o 902.3MHz ~ 927.3 MHz
▪ 26 Channels, Channel Spacing 1MHz
• Modulation: LoRa®
• Spreading Factor:
• 500kHz BW: 7~12
• 125kHz BW: 7~10
The host product manufacturer must ensure that the RF behavior adheres to the certification (e.g.
FCC, ISED) requirements when the module is installed in the final host product.
The availability of some specific channels and/or operational frequency bands are country dependent
and should be programmed at the Host product factory to match the intended destination. Regulatory
bodies prohibit exposing the settings to the end user. This requirement needs to be taken care of via
Host implementation.
The Host product manufacturer must ensure that the RF behavior adheres to the certification (e.g. FCC,
ISED) requirements when the module is installed in the final Host product.
1.4 Host Board Top Layer Instructions:
3
Revision 0.0 (07/2020)
Preliminary
The top layer (underneath the module) of the host PCB must be ground with as many GND vias as
possible.
2 WLR089U0/WLR089UC Usage Instructions under Modular Approval
The WLR089U0 module has received regulatory approval for the following countries:
– United States/FCC ID: 2ADHKR34M
– Canada/ISED:
• IC: 20266-R34M
• HVIN: WLR089U0
• PMN: WLR089U
The WLR089UC module has received regulatory approval for the following countries:
– United States/FCC ID: 2ADHKR34M
– Canada/ISED:
• IC: 20266-R34M
• HVIN: WLR089UC
• PMN: WLR089U
2.1 United States
The WLR089U0/WLR089UC module has received Federal Communications Commission (FCC) CFR47
Telecommunications, Part 15 Subpart C “Intentional Radiators” single-modular approval in accordance with
Part15.212 Modular Transmitter approval. Single-modular transmitter approval is defined as a complete RF trans-
mission sub-assembly, designed to be incorporated into another device, that must demonstrate compliance with
FCC rules and policies independent of any host. A transmitter with a modular grant can be installed in different
end-use products (referred to as a host, host product, or host device) by the grantee or other equipment
manufacturer, then the host product may not require additional testing or equipment authorization for the
transmitter function provided by that specific module or limited module device.
The user must comply with all of the instructions provided by the Grantee, which indicate installation and/or
operating conditions necessary for compliance.
The host product itself is required to comply with all other applicable FCC equipment authorizations regulations,
requirements and equipment functions that are not associated with the transmitter module portion. For example,
compliance must be demonstrated: to regulations for other transmitter components within a host product; to
requirements for unintentional radiators(Part 15 Subpart B), such as digital devices, computer peripherals, radio
receivers, etc.; and to additional authorization requirements for the non-transmitter functions on the transmitter
module (i.e., Suppliers Declaration of Conformity (SDoC) or certification) as appropriate (for example, Bluetooth
and Wi-Fi transmitter modules may also contain digital logic functions).
2.1.1 LABELING AND USER INFORMATION REQUIREMENTS
The WLR089U0/WLR089UC module has been labeled with its own FCC ID number, and if the FCC
ID is not visible when the module is installed inside another device, then the outside of the finished
product into which the module is installed must also display a label referring to the enclosed module.
This exterior label can use wordings follows:
For the WLR089U0/WLR089UC
Contains Transmitter Module
FCC ID: 2ADHKR34M
or
4
Revision 0.0 (07/2020)
Preliminary
Contains FCC ID: 2ADHKR34M
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation
A user’s manual for the product must include the following statement:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna
•Increase the separation between the equipment and receiver
•Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
•Consult the dealer or an experienced radio/TV technician for help
Additional information on labeling and user information requirements for Part 15 devices can be found
in KDB Publication 784748, which is available at the FCC Office of Engineering and Technology
(OET) Laboratory Division Knowledge Database (KDB) https://apps.fcc.gov/oetcf/kdb/index.cfm
2.1.2 RF EXPOSURE
All transmitters regulated by FCC must comply with RF exposure requirements. KDB 447498 General
RF Exposure Guidance provides guidance in determining whether proposed or existing transmitting
facilities, operations or devices comply with limits for human exposure to Radio Frequency (RF) fields
adopted by the Federal Communications Commission (FCC).
From the FCC Grant: Output power is conducted. This grant is valid only when the module is sold to
OEM integrators and must be installed by the OEM or OEM integrators. This transmitter is restricted
for use with the specific antenna(s) tested in this application for Certification. The antenna(s) used
with this transmitter must be installed to provide a separation distance of at least 20 mm from all
persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
Users and installers must be provided with antenna installation instructions and transmitter operating
conditions for satisfying RF exposure compliance.
2.1.3 APPROVED EXTERNAL ANTENNAS
To maintain modular approval in the United States, only the antenna types that have been tested shall
be used. It is permissible to use different antenna, provided the same antenna type, antenna gain
(equal to or less than), with similar in-band and out of band characteristics (refer to specification sheet
for cutoff frequencies).
For WLR089U0/WLR089UC, Testing was performed with the antenna types listed in table mentioned
in the Table 1-1.
2.1.4 MODULE INTEGRATION IN THE HOST PRODUCT
Host products are to ensure continued compliance as per KDB 996369 Module Integration Guide.
2.1.5 HELPFUL WEB SITES
Federal Communications Commission (FCC): https://www.fcc.gov/
FCC Office of Engineering and Technology (OET) Laboratory Division Knowledge Database (KDB):
https://apps.fcc.gov/oetcf/kdb/index.cfm
5
Revision 0.0 (07/2020)
Preliminary
2.2 Canada
The WLR089U0/WLR089UC module has been certified for use in Canada under Innovation, Science
and Economic Development Canada (ISED, formerly Industry Canada) Radio Standards Procedure
(RSP) RSP-100, Radio Standards Specification (RSS) RSS-Gen and RSS-247. Modular approval
permits the installation of a module in a host device without the need to recertify the device.
2.2.1 LABELING AND USER INFORMATION REQUIREMENTS
Labeling Requirements (from RSP-100, Issue 12, Section 5): The host product shall be properly
labeled to identify the module within the host device.
The Innovation, Science and Economic Development Canada certification label of a module shall be
clearly visible at all times when installed in the host product, otherwise the host device must be
labeled to display the Innovation, Science and Economic Development Canada certification number of
the module, preceded by the word “Contains”, or similar word expressing the same meaning, as
follows:
For the WLR089U0/WLR089UC:
Contains IC: 20266-R34M
User Manual Notice for License-Exempt Radio Apparatus (from Section 8.4 RSS-Gen, Issue 5, March
2019): User manuals for license-exempt radio apparatus shall contain the following or equivalent
notice in a conspicuous location in the user manual or alternatively on the device or both:
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following
two conditions:
1. This device may not cause interference;
2. This device must accept any interference, including interference that may cause undesired
operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
Transmitter Antenna (From Section 6.8 RSS-GEN, Issue 5, March 2019): User manuals, for
transmitters shall display the following notice in a conspicuous location:
This radio transmitter [IC: 20266- R34M] has been approved by Innovation, Science and Economic
Development Canada to operate with the antenna types listed above, with the maximum permissible
gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain
indicated for any type listed are strictly prohibited for use with this device.
Le présent émetteur radio [IC: 20266- R34M] a été approuvé par Innovation, Sciences et
Développement économique Canada pour fonctionner avec les types d'antenne énumérés cidessous
et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain
est supérieur au gain maximal indiqué pour tout type figurant sur la liste, sont strictement interdits
pour l'exploitation de l'émetteur.
Immediately following the above notice, the manufacturer shall provide a list of all antenna types
which can be used with the transmitter, indicating the maximum permissible antenna gain (in dBi) and
the required impedance for each antenna type.
2.2.2 RF EXPOSURE
All transmitters regulated by the Innovation, Science and Economic Development Canada (ISED)
must comply with RF exposure requirements listed in RSS-102 - Radio Frequency (RF) Exposure
Compliance of Radio communication Apparatus (All Frequency Bands).
This transmitter is restricted for use with a specific antenna tested in this application for certification,
and must not be co-located or operating in conjunction with any other antenna or transmitters, except
6
Revision 0.0 (07/2020)
Preliminary
in accordance with Innovation, Science and Economic Development Canada multi-transmitter
guidelines.
The module antenna must be installed to meet the RF exposure compliance separation distance of “35
mm” and any additional testing and authorization process as required.
The host integrator installing this module into their product must ensure that the final composite product
complies with the ISED requirements by a technical assessment.
L'antenne du module doit être installé pour répondre à la conformité en matière d'exposition RF distance
de séparation de 35 "mm" et tout d'autres tests et processus d'autorisation au besoin.
L'hôte integrator l'installation de ce module dans leur produit final doit s'assurer que le produit est
conforme à la composite Exigences ISED par une évaluation technique.
2.2.3 APPROVED EXTERNAL ANTENNAS
For WLR089U0/WLR089UC, the testing was performed with the antenna types listed in table
mentioned in the Table 1-1.
2.2.4 HELPFUL WEBSITES
Innovation, Science and Economic Development Canada (ISED): http://www.ic.gc.ca/
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

MICROCHIP WLR089U0 Regulatory Compliance Manuel utilisateur

WLR089U0 Regulatory Compliance
MICROCHIP
Marque
MICROCHIP
Modèle
WLR089U0 Regulatory Compliance
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents