MICROCHIP WBZ451 Manuel utilisateur

Marque: MICROCHIP

Modèle: WBZ451

Taper: Manuel utilisateur

Draft Manual

A-page 1

and its subsidiaries

WBZ451_Regulatory Approval

WBZ451

Draft Manual

A-page 2

and its subsidiaries

Table of Contents

1. Appendix A: Regulatory Approval ..................................................................................................................... 3

1.1. United States ........................................................................................................................................... 3

1.2. Canada ..................................................................................................................................................... 4

1.3. Europe ...................................................................................................................................................... 5

1.4. Other Regulatory Information ................................................................................................................ 7

WBZ451

Appendix A: Regulatory Approval

Draft Manual

A-page 3

and its subsidiaries

1. Appendix A: Regulatory Approval

The WBZ451 module(1) has received regulatory approval for the following countries:

• Bluetooth Special Interest Group (SIG) QDID:

– WBZ451 with Class 1(2) : 134083

– WBZ451 (3) : 134099

• United States/FCC ID: 2ADHKWBZ451

• Canada/ISED:

– IC: 20266-WBZ451

– HVIN: WBZ451PE, WBZ451UE, WBZ451PC, WBZ451UC

• Europe/CE

• Japan/MIC: TBD

• Korea/KCC: TBD

• Taiwan/NCC: TBD

• China/SRRC: CMIIT ID: TBD

1.1 United States

The WBZ451 module has received Federal Communications Commission (FCC) CFR47 Telecommunications, Part

15 Subpart C “Intentional Radiators” single-modular approval in accordance with Part 15.212 Modular Transmitter

approval. Single-modular transmitter approval is defined as a complete RF transmission sub-assembly, designed to

be incorporated into another device, that must demonstrate compliance with FCC rules and policies independent of

any host. A transmitter with a modular grant can be installed in different end-use products (referred to as a host,

host product or host device) by the grantee or other equipment manufacturer, then the host product may not require

additional testing or equipment authorization for the transmitter function provided by that specific module or limited

module device.

The user must comply with all of the instructions provided by the Grantee, which indicate installation and/or operating

conditions necessary for compliance.

A host product itself is required to comply with all other applicable FCC equipment authorization regulations,

requirements, and equipment functions that are not associated with the transmitter module portion. For example,

compliance must be demonstrated: to regulations for other transmitter components within a host product; to

requirements for unintentional radiators (Part 15 Subpart B), such as digital devices, computer peripherals, radio

receivers, etc.; and to additional authorization requirements for the non-transmitter functions on the transmitter

module (i.e., Suppliers Declaration of Conformity (SDoC) or certification) as appropriate (e.g., Bluetooth and Wi-Fi

transmitter modules may also contain digital logic functions).

1.1.1 Labeling and User Information Requirements

The WBZ451 module has been labeled with its own FCC ID number, and if the FCC ID is not visible when the module

is installed inside another device, then the outside of the finished product into which the module is installed must

display a label referring to the enclosed module. This exterior label must use the following wording:

The user's manual for the finished product must include the following statement:

Contains Transmitter Module FCC ID: 2ADHKWBZ451

Contains FCC ID: 2ADHKWBZ451

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

WBZ451

Appendix A: Regulatory Approval

Draft Manual

A-page 4

and its subsidiaries

Additional information on labeling and user information requirements for Part 15 devices can be found in KDB

Publication 784748, which is available at the FCC Office of Engineering and Technology (OET) Laboratory Division

Knowledge Database (KDB) apps.fcc.gov/oetcf/kdb/index.cfm.

1.1.2 RF Exposure

All transmitters regulated by FCC must comply with RF exposure requirements. KDB 447498 General RF Exposure

Guidance provides guidance in determining whether proposed or existing transmitting facilities, operations

or devices comply with limits for human exposure to Radio Frequency (RF) fields adopted by the Federal

Communications Commission (FCC).

From the FCC Grant: Output power listed is conducted. This grant is valid only when the module is sold to OEM

integrators and must be installed by the OEM or OEM integrators. This transmitter is restricted for use with the

specific antenna(s) tested in this application for Certification and must not be co-located or operating in conjunction

with any other antenna or transmitters within a host device, except in accordance with FCC multi-transmitter product

procedures.

WBZ451: These modules are approved for installation into mobile or/and portable host platforms atleast 20cm away

from the human body

1.1.3 Helpful Web Sites

• Federal Communications Commission (FCC): www.fcc.gov.

• FCC Office of Engineering and Technology (OET) Laboratory Division Knowledge Database (KDB) apps.fcc.gov/

oetcf/kdb/index.cfm.

1.2 Canada

The WBZ451 module has been certified for use in Canada under Innovation, Science and Economic Development

Canada (ISED, formerly Industry Canada) Radio Standards Procedure (RSP) RSP-100, Radio Standards

Specification (RSS) RSS-Gen and RSS-247. Modular approval permits the installation of a module in a host device

without the need to recertify the device.

1.2.1 Labeling and User Information Requirements

Labeling Requirements (from RSP-100 - Issue 12, Section 5): The host product shall be properly labeled to identify

the module within the host device.

The Innovation, Science and Economic Development Canada certification label of a module shall be clearly visible

at all times when installed in the host device; otherwise, the host product must be labeled to display the Innovation,

Science and Economic Development Canada certification number of the module, preceded by the word “Contains” or

similar wording expressing the same meaning, as follows:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Contains IC: 20266-WBZ451

WBZ451

Appendix A: Regulatory Approval

Draft Manual

A-page 5

and its subsidiaries

User Manual Notice for License-Exempt Radio Apparatus (from Section 8.4 RSS-Gen, Issue 5, February 2021): User

manuals for license-exempt radio apparatus shall contain the following or equivalent notice in a conspicuous location

in the user manual or alternatively on the device or both:

Transmitter Antenna (From Section 6.8 RSS-GEN, Issue 5, February 2021): User manuals, for transmitters shall

display the following notice in a conspicuous location:

Immediately following the above notice, the manufacturer shall provide a list of all antenna types approved for use

with the transmitter, indicating the maximum permissible antenna gain (in dBi) and required impedance for each.

1.2.2 RF Exposure

All transmitters regulated by Innovation, Science and Economic Development Canada (ISED) must comply with RF

exposure requirements listed in RSS-102 - Radio Frequency (RF) Exposure Compliance of Radiocommunication

Apparatus (All Frequency Bands).

This transmitter is restricted for use with a specific antenna tested in this application for certification, and must not

be co-located or operating in conjunction with any other antenna or transmitters within a host device, except in

accordance with Canada multi-transmitter product procedures.

WBZ451: The device operates at an output power level which is within the ISED SAR test exemption limits at any

user distance > 20cm.

1.2.3 Helpful Web Sites

Innovation, Science and Economic Development Canada (ISED): www.ic.gc.ca/.

1.3 Europe

The WBZ451 module has is/are a Radio Equipment Directive (RED) assessed radio module that is CE marked and

has been manufactured and tested with the intention of being integrated into a final product.

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and

Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two

conditions:

(1) This device may not cause interference;

(2) This device must accept any interference, including interference that may cause undesired operation of

the device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR

d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts

de licence. L’exploitation est autorisée aux deux conditions suivantes:

1. L’appareil ne doit pas produire de brouillage;

2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en

compromettre le fonctionnement.

This radio transmitter [IC: 20266-WBZ451] has been approved by Innovation, Science and Economic

Development Canada to operate with the antenna types listed below, with the maximum permissible gain

indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated

for any type listed are strictly prohibited for use with this device.

Le présent émetteur radio [IC: 20266-WBZ451] a été approuvé par Innovation, Sciences et Développement

économique Canada pour fonctionner avec les types d'antenne énumérés cidessous et ayant un gain

admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au

gain maximal indiqué pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de

l'émetteur.

WBZ451

Appendix A: Regulatory Approval

Draft Manual

A-page 6

and its subsidiaries

The WBZ451 module has has/have been tested to RED 2014/53/EU Essential Requirements mentioned in the

following European Compliance table.

Table 1-1. European Compliance Information

Certification

Standard

Article

Safety

EN 62368

3.1a

Health

EN 62311

EMC

EN 301 489-1

3.1b

EN 301 489-17

Radio

EN 300 328

3.2

The ETSI provides guidance on modular devices in the “Guide to the application of harmonised standards

covering articles 3.1b and 3.2 of the RED 2014/53/EU (RED) to multi-radio and combined radio and non-

radio equipment” document available at http://www.etsi.org/deliver/etsi_eg/203300_203399/20 3367/01.01.01_60/

eg_203367v010101p.pdf.

Note: To maintain conformance to the standards listed in the preceding European Compliance table, the module

shall be installed in accordance with the installation instructions in this data sheet and shall not be modified. When

integrating a radio module into a completed product, the integrator becomes the manufacturer of the final product and

is therefore responsible for demonstrating compliance of the final product with the essential requirements against the

RED.

1.3.1 Labeling and User Information Requirements

The label on the final product that contains the WBZ451 module has must follow CE marking requirements.

1.3.2 Conformity Assessment

From ETSI Guidance Note EG 203367, section 6.1, when non-radio products are combined with a radio product:

If the manufacturer of the combined equipment installs the radio product in a host non-radio product in equivalent

assessment conditions (i.e. host equivalent to the one used for the assessment of the radio product) and according to

the installation instructions for the radio product, then no additional assessment of the combined equipment against

article 3.2 of the RED is required.

1.3.2.1 Simplified EU Declaration of Conformity

Hereby, Microchip Technology Inc. declares that the radio equipment type WBZ451 is in compliance with Directive

2014/53/EU.

The full text of the EU declaration of conformity, for this product, is available at www.microchip.com/design-centers/

wireless-connectivity/.

1.3.3 Helpful Websites

A document that can be used as a starting point in understanding the use of Short Range Devices (SRD) in Europe is

the European Radio Communications Committee (ERC) Recommendation 70-03 E, which can be downloaded from

the European Communications Committee (ECC) at: http://www.ecodocdb.dk/.

Additional helpful web sites are:

• Radio Equipment Directive (2014/53/EU):

https://ec.europa.eu/growth/single-market/european-standards/harmonised-standards/red_en

• European Conference of Postal and Telecommunications Administrations (CEPT):

http://www.cept.org

• European Telecommunications Standards Institute (ETSI):

http://www.etsi.org

• The Radio Equipment Directive Compliance Association (REDCA):

http://www.redca.eu/

WBZ451

Appendix A: Regulatory Approval

Draft Manual

A-page 7

and its subsidiaries

1.4 Other Regulatory Information

• For information about other countries' jurisdictions not covered here, refer to the www.microchip.com/design-

centers/wireless-connectivity/certifications.

• Should other regulatory jurisdiction certification be required by the customer, or the customer needs to recertify

the module for other reasons, contact Microchip for the required utilities and documentation.

1.5 List of certified antenna

Sl.No

Part

Number

Vendor

Antenna

type

Gain

Comment

W3525B039

Pulse

PCB

2dBi

Cable Length 100mm

001-0016

LSR

PIFA

2.5dBi

Flex PIFA antenna

001-0001

LSR

Dipole

2dBi

RPSMA connector*

1461530100

Molex

PCB

3dBi

100mm (Dual Band)

ANT-2.4-

LPW-125

Linx

Technologies

Dipole

2.8dBi

125mm

RFA-02-P05-

D034

Alead

PCB

2dBi

150mm

RFA-02-P33-

D034

Alead

PCB

2dBi

150mm

ABAR1504-

S2450

ABRACON

PCB

2.28dBi

250mm

WBZ451

LGA

2.36dBi

WBZ451

Draft Manual

A-page 8

and its subsidiaries

Draft Manual

A-page 9

and its subsidiaries

MICROCHIP WBZ451 Manuel utilisateur

Marque: MICROCHIP

Modèle: WBZ451

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: MICROCHIP WBZ451 User manual

MICROCHIP WBZ451 Manuel utilisateur

MICROCHIP WBZ451 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents