Sonoff MINIR4 Extreme WiFi Smart Switch Manuel utilisateur

Marque: Sonoff

Modèle: MINIR4 Extreme WiFi Smart Switch

Taper: Manuel utilisateur

·中文 ----------1 - 7 · English ----------8 - 14 · Warning ----------15 - 16

MINI Extreme

Wi-Fi Smart Switch

产品介绍

设备重量＜1Kg，建议安装高度＜2米。

按键

接线端口

网络指示灯

信号指示灯状态说明

指示灯状态状态说明

蓝灯呈两短一长闪烁配网模式

设备在线蓝色常亮

功能特点

MINI Extreme紧凑小巧的机身，能够安装在开关暗盒中且最大支持10A负载，使普通开关变为智

能开关。安全且智能，也可在智能场景中联动其他设备，实现你的家庭自动化。

设备安装

1. 断电

设备安装、故障维修请由专业资质电工操作。切勿在设备通电时进行接线操作或触碰到接线

端子，以免发生触电危险！

语音控制

智能场景

远程控制

通电反应

局域网控制

群组控制

智能定时/延时

点动模式

配对至易微联App

1. 下载易微联App

请前往应用商店、Google Play Store或Apple App Store搜索"易微联"进行下载。

2. 接线

1. S1、S2 接或不接开关，设备都可通过自动化或App来控制。

2. 禁止将S1、S2端子连接零线或地线，以免损坏设备,造成危险。

3. 确保线路接入无误。

为确保电气安装的安全，必须在MINIR4前面安装符合国家安全标准额定电流为 10A 的微型断

路器 (MCB) 或漏电断路器 (RCBO)。

3.添加设备

打开“易微联”App, 点击“+”. 选择“添加设备”，再根据 App 提示进行操作。

2. 上电

通电后，设备首次使用，默认进入配网模式。网络指示灯呈“两短一长闪烁”。

10分钟内没有进行配网，设备将退出配网模式。如需再次进入，长按设备按钮5秒直到网络指

示灯呈两短一长闪烁即可。

添加设备时必须打开手机蓝牙

添加轻智能子设备

将MINI Extreme安装在暗盒中

进入 eWeLink App 设备设置页面，选择“轻智能子设备”再点击“ 添加”，然后触发子设备，即可添

加成功。

设备设置轻智能子设备

添加

快捷设置

位置管理

分享设备

创建群组

小程序控制

局域网控制

设备设置

网络指示灯

轻智能子设备 0/8

产品参数

产品型号

输入

输出

最大功率

Wi-Fi

工作温度

工作湿度

外壳材料

产品规格

MINIR4

100-240V ~ 50/60Hz 10A Max

2400W

IEEE 802.11b/g/n 2.4GHz

-10℃ ~ 40℃

5%-95%RH,无冷凝

PC V0

39.5x33x16.8mm

执行标准：GB/T 16915.2-2012

产品中有害物质的名称及含量

部件名称

塑料件

本表格依据SJ/T 11364 的规定编制：

o：表示该有害物质在该部件所有均质材料中的含量均在GB/T 26572规定的限量要求以下；

x：表示该有害物质至少在该部件的某一均质材料中的含量超出GB/T 26572规定的限量要求。

o o o o o o

x o o o o o

o o o o o o

电子元器件

包装盒

铅

(Pb)

汞

(Hg)

镉

(Cd)

六价铭

(Cr｛VI｝

多溴联苯

(PBB)

多溴二苯醚

(PBDE)

有害物质

PCB板

在 eWeLink App 设备设置界面选择 “WiFi设置” 进行更换。

更换设备网络

常见问题

1. Wi-Fi设备与易微联App配对失败

1、确保设备进入配对模式.

10分钟内设备没有配对成功，则自动退出配对模式。

2、请开启定位服务以及允许获取定位权限

配网前，请先开启手机的定位服务并允许获取定位权限。位置信息权限用于获取Wi-Fi列表信息，

如果“禁用”手机定位服务，设备将无法添加。

在 eWeLink App 端“删除设备”，设备即恢复出厂设置。

恢复出厂设置

3、确保Wi-Fi运行在2.4GHz频段。

4、确保正确输入Wi-Fi网络名称和密码，且没有包含特殊字符。

密码错误是常见的配对失败原因。

5、配对时为了确保良好的信号传输，请将设备靠近路由器。

2. LED指示灯连续闪烁两次，服务器连接失败

1、确保网络连接正常。你可以通过手机或者电脑连接网络。如果连接失败，请检查网络。

2、路由器承载力较低，连接到路由器的设备超过最大值。请查看你的路由器可以连接的最大设

备数量。如果超过最大值，请删除个别设备或者更换一个承载力较高的路由器再次连接。

如果以上方法均无法解决此问题，请在易微联APP上通过“帮助&反馈”提交你的问题。

3. Wi-Fi设备“离线”问题

1、路由器连接失败

2、输入不正确的Wi-Fi网络名称和密码

3、 Wi-Fi网络名称和密码包含特殊字符。例如，我们的系统无法识别希伯来语和阿拉伯语字符，

导致Wi-Fi连接失败

4、路由器承载力较低

5、 Wi-Fi信号太弱。路由器和设备间隔太远，或者路由器与设备之前有障碍物导致信号无法传输。

English

Button

Wiring ports

Network indicator

Product introduction

Instruction of LED indicator status

LED indicator status Status instruction

Blue LED indicator ﬂashes

(one long and two short) Pairing mode

Device is onlineBlue LED indicator keeps on

The device weight is less than 1kg, and the recommended installation height is less

than 2m.

English

Features

MINI Extreme is compact and tiny enough to be installed in the mounted box, and it

supports loads of up to 10A, enable to transform your ordinary switch into a smart switch.

Safe and smart, allows you to set smart scenes with other smart devices to automate your

home.

Voice Control

Smart Scene

Remote Control

Power-on State

LAN Control

Group Control

Timer Schedule

Inching Mode

Installation

1. Power oﬀ

Please install and maintain the device by a professional electrician. To avoid electric

shock hazard, do not operate any connection or contact the terminal connector while

the device is powered on!

English

Pair with eWeLink App

1. Download the eWeLink App

Please download the "eWeLink" App from Google Play Store or Apple App Store.

2. Wiring instruction

To ensure the safety of your electrical installation, it's essential either a Miniature Circuit

Breaker (MCB) or a Residual Current Operated Circuit Breaker (RCBO) with an electrical

rating of 10A has been installed before the MINIR4.

1No matter S1 and S2 are connected or left idle to the external switch, this device

canbe controlled by automation or the App.

2It is prohibited to connect S1 and S2 terminals to the neutral or ground wire, in order

to avoid damaging the equipment and causing danger.

3Make sure all wires are connected correctly.

English

It's required to turn on the Bluetooth on your Phone when adding a device.

3.Add device

Open the eWeLink App, Tap “+” and select “Add Device”, then operate following the

prompt on the App.

2. Power on

After powering on, the device will enter the Pairing Mode defaulted during

the ﬁrst use, and the Network indicator ﬂashes in a cycle of two short and one long.

The device will exit the Pairing Mode if not been paired within 10mins. If you want to

enter this mode again, please long press the button for 5s until the Network indicator

ﬂashes in a cycle of two short and one long and then release.

English

Add eWeLink-Remote Sub-devices

Install the MINI Extreme in the mounting box

Enter the Device Settings page on the eWeLink App, select "eWeLink-Remote sub-devices"

and tap "Add", then trigger the sub-device to add it successfully.

English

Change the device's network by "Wi-Fi Settings" in the "Device Settings" page on the

eWeLink App.

Speciﬁcations

Model

Input

Output

Max. power

Wi-Fi

Working temperature

Working humidity

Casing material

Dimension

MINIR4

100-240V ~ 50/60Hz 10A Max

2400W

IEEE 802.11b/g/n 2.4GHz

-10℃ ~ 40℃

5%-95% RH, non-condensing

PC V0

39.5x33x16.8mm

Device Network Changing

FAQ (Frequently Asked Questions)

1. Fail to pair Wi-Fi devices with the eWeLink App

1Make sure the device is in pairing mode.

The device will automatically exit the pairing mode if it is not paired within 10mins.

2Please enable location service and allow access to location permission.

Before connecting Wi-Fi network, please enable the location service and allow access

to the location permission. Location information permission is used to obtain Wi-Fi list

information, if you "disable" the location service, the device cannot be paired.

Reset the device to factory settings by "Delete device" on the eWeLink App.

Factory Reset

English

3Make sure your Wi-Fi works on 2.4GHz band.

4Make sure to enter the Wi-Fi SSID and password correctly without special characters.

Incorrect password is a common cause of pairing failure.

5To ensure good signal transmission while pairing, please place the device close to

the router.

2. The LED indicator ﬂashes twice on repeated means the server

fails to connect.

1Make sure the networking is normal. Check the internet works well by connecting

your phone or PC. If fail to connect, please check the availability of the Internet

connection.

2.With the low load capacity of the router, the connected devices exceed the router's

maximum load capacity. Please check the maximum number of devices that your

router can carry, if the connected devices exceed the maximum value, remove some

devices or use a higher load capacity router.

If the above methods cannot help to solve the problem, please submit your problem

to "Help & Feedback" on the eWeLink App.

3. Wi-Fi devices are "oﬄine"

1Devices fail to connect to the router.

2Entered the wrong Wi-Fi SSID and password.

3Wi-Fi SSID and password contain special characters, for example, our system can't

recognize Hebrew and Arabic characters, which causes Wi-Fi connections to fail.

4Low capacity of the router.

5Wi-Fi signal is weak. The router and the devices are too far apart, or there is an

obstacle between the router and the device, which prevents the signal from being

transmitted.

Warning

FCC Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may

cause undesired operation.

2.Changes or modiﬁcations not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment oﬀ and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit diﬀerent

from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for

help.

FCC Radiation Exposure statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance of

20 cm between the radiator and your body. This transmitter must not be co-located or

operating in conjunction with any other antenna or transmitter.

Warning

ISED Notice

This device contains licence-exempt transmitter(s)/receiver(s) that comply with

Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions:

(1)This device may not cause interference.

(2)This device must accept any interference, including interference that may cause

undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES-003.

This device complies with RSS-247 of Industry Canada.

Operation is subject to the condition that this device does not cause harmful

interference.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme

aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux

appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions

suivantes :

(1)L’appareil ne doit pas produire de brouillage;

(2)L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est

susceptible d’en compromettre le fonctionnement.

Cet appareil numérique de la Classe B conforme à la norme NMB-003 du Canada.

Cet appareil est conforme à la norme RSS-247 d'Industrie Canada. Le fonctionnement est

soumis à la condition que cet appareil ne provoque pas d'interférences nuisibles.

ISED Radiation Exposure Statement

This equipment complies with ISED radiation exposure limits set forth for an

uncontrolled environment.

This equipment should be installed and operated with minimum distance of 20 cm

between the radiator and your body.

This transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.

Cet équipement est conforme aux limites d’exposition aux rayonnements de la ISED

établies pour unenvironnement non contrôé.

Cet équipement doit être installé et fonctionner à au moins 20cm de distance d’un

radiateur ou de votre corps.

Cet émetteur ne doit pas être co-localisé ou fonctionner en conjonction avec une autre

antenne ou un autre émetteur.

Warning

Hereby, Shenzhen Sonoﬀ Technologies Co., Ltd. declares that the radio equipment type

MINIR4 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of

conformity is available at the following internet address:

https://sonoﬀ.tech/usermanuals

EU Declaration of Conformity

WEEE Warning

WEEE Disposal and Recycling Information All products bearing this symbol are

waste electrical and electronic equipment (WEEEas in directive 2012/19/EU)

which should not be mixed with unsorted householdwaste. Instead, you should

protect human health and the environment by handingover your waste

equipment to a designated collection point for the recycling of waste

electricaland electronic equipment, appointed by the government or local

authorities. Correct disposaland recycling will help prevent potential negative

consequences to the environment and human health. Please contact the

installer or local authorities for more information about thelocation as well as

terms and conditions of such collection points.

SAR Warning

Under normal use of condition, this equipment should be kept a separation distance of at

least 20cm between the antenna and the body of the user.

Dans des conditions normales d’utilisation, cet équipement doit être maintenu à une distance

d’au moins 20cm entre l’antenne et le corps de l’utilisateur.

Scatola

PAP 21

Carta

RACCOLTA DIFFERENZIATA

Veriﬁca le disposizioni del tuo Comune.

Separa le componenti e conferiscile in modo corretto.

Manuale

PAP 22

Carta

Neto

EVA 7

Plastica

For CE Frequency:

Operation frequency Range:

2402-2480MHz(BLE)

2412-2472MHz(Wi-Fi)

RF Output Power:

1.87dBm(BLE)

16.12dBm(802.11b),15.80dBm(802.11g),15.67dBm(802.11n20),

13.33dBm(802.11n40)(Wi-Fi)

Cet appareil

se recycle

À DÉPOSER

EN MAGASIN À DÉPOSER

EN DÉCHÈTERIE

FRFR

Sonoff MINIR4 Extreme WiFi Smart Switch Manuel utilisateur

Marque: Sonoff

Modèle: MINIR4 Extreme WiFi Smart Switch

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Sonoff MINIR4 Extreme WiFi Smart Switch User manual
日本語: Sonoff MINIR4 Extreme WiFi Smart Switch ユーザーマニュアル

Sonoff MINIR4 Extreme WiFi Smart Switch Manuel utilisateur

Sonoff MINIR4 Extreme WiFi Smart Switch Manuel utilisateur

dans d''autres langues

Documents connexes