Raddy WF-55C Manuel utilisateur

Catégorie
Stations météo
Taper
Manuel utilisateur
WEATHER STATION
USER MANUAL
Please read the instruction before using the product and keep it for
future reference.
Any questions, please feel free to contact support@iraddy.com or visit
www.iraddy.com
WF-55C
39-51
USER MANUAL
BEDIENUNGSANLEITUNG
MANUALE D'USO
MANUEL UTILISATEUR
01-12
13-25
26-38
LANGUAGE INDEX
READ BEFORE USE
IMPORTANT PLACEMENT GUIDELINES
PACKAGE CONTENTS
INSTALLATION
OVERVIEW
FEATURES
CHANNEL SETTING
FUNTIONS SETTING MODE
TOUCH ADJUSTABLE BACKLIGHT
ALARM CLOCK SETTING
SNOOZE SETTING
LOW BATTERY ALERT
MAX/MIN RECORD
WEATHER FORECAST
COMFORT INDEX
LOW TEMPERATURE ALERT
TRENDS
TROUBLE SHOOTING
SPECIFICATION
CONTENTS
01
01
02
02
04
06
07
07
08
08
08
09
09
10
10
10
11
11
12
READ BEFORE USE
IMPORTANT PLACEMENT GUIDELINES
01
Do not clean any part of the product with benzene, thinner
or other solvent chemicals. If necessary, clean it with a soft
cloth.
Do not dismantle or modify the product in any way.
Never immerse the product in water, It will damage the product.
Do not subject the product to extreme force, shock, or
fluctuations in temperature or humidity.
Do not tamper with the internal components.
Do not use new and used batteries.
Do not use different types of batteries alkaline, standard or
rechargeable batteries with this product.
Remove the batteries if storing this product for a long period
of time, otherwise the battery might damage the product.
Do not dispose of this product as unsorted municipal waste,
it’s necessary to separately collect it for special treatment.
Do not place the base station in rain or moisture.
The transmit range depends on the type of obstacles
located between the transmitter and the receiver (e.g. a
concrete wall will interfere with the signal much more than a
plasterboard wall).
Be sure the sensor is mounted vertically, to allow moisture
to drain out properly. Place out of direct sunlight & ensure
the sensor is well-ventilated.
1. The distance between base station and sensors should be
at least 5 ~ 6.5 feet (1.5~2 meters) away from any
interfering sources such as computer monitors or TV sets.
2. The base station stay away from the metal window frames.
3. Please do not use other electrical products such as
headphones or microphone operating on the same signal
frequency. (433.92MHz), neighbors using electrical devices
operating on the same signal frequency can also cause
interference.
PACKAGE CONTENTS
1 x Weather Station
1 x Remote Sensor
1 x User Manual
1 x DC Adapter
*Alkaline batteries are not included
Sensor Set Up
INSTALLATION
Base station supports up to 3 sensors connection, the sensor
switch is located inside the battery compartment, it can be
switched 1,2,3, matching the info of Channel 1, Channel 2,
Channel 3 that synchronize on the OUTDOOR Dashboard,
install 2 alkaline AA batteries to activate the sensor.
Base Station Set Up
Remove the protective film that is applied to the LCD screen
prior to using the product.
Plugged in with power adapter and use, battery-power is
321
02
4. Place the base station in a dry area, free of dirt and dust. To
ensure accurate temperature measurement, place out of
direct sunlight and away from heat sources or vents.
LR03/R03 AAA 1.5V
+_
LR03/R03 AAA 1.5V
+_
Connect The Sensor & Base Station
1. Install the batteries for the remote sensor, and slide the
channel number.
2. Plug the power adapter into the base station, then it will start
to receive the sensor signal within 3 minutes.
3. If the red indicator of the sensor flash twice, and you see the
detected data displayed located on the left of screen , it
means the sensor is connected with the base station.
4. When the red indicator of sensor flash for once per minute, it
indicates that it is updating the sensor data to base station.
Example, when you slide to channel 1 for your sensor, you can
see the data shown the data on the CH1 dashboard.
03
optional, since previous setting will be reset when plugged out,
we recommend install the batteries for the base station.
Base station can stand upright on the table or mount on the wall.
OVERVIEW
1
15 14 13 12 11 10
17
16
2 3 4 5 6 7
8
9
19
20 20
21
22
19 19 19
18
04
Time
Outdoor humidity
Comfort dashboard for
outdoor
Max/Min record for outdoor
temperature and humidity in
24hours
Outdoor Temperature
Touch button - ( )
SNOOZE/LIGHT
SET = function setting button
▲/CH = up or channel switch,
▼/MEM = down or MAX/MIN
records checking
ALARM = Alarm clock setting)
Hang Holes for wall mounting
Table stand
Battery compartment cover
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
17
16
18
19
20
21
22
Channel
3 outdoor channels display
in loop
Low battery indicator
(Sensor)
Weather forecast
FREEZE WARNING
Indoor temperature
Low battery Indicator
(base station)
Trends for indoors
temperature and humidity
Max/Min record for indoor
temperature and humidity
in 24hours
Comfort dashboard for indoor
Indoor humidity
Calendar
05
Sensore Remoto
1. Time and Calendar (Day/Month)
2. 12/24 hours format switchable
3. Alarm with snooze function
4. Weather forecast with 5 variables: sunny, partly cloudy,
cloudy, rainy, and snowy
5. Indoor temperature and humidity
6. Outdoor temperature and humidity
7. Support up to 3 sensors (1 included)
8. Automatically loop temperature and humidity of 3 outdoor
sensors
9. Max/ Min memory records for all indoor/outdoor temperature
and humidity
10. Trend index
11. C/F(Celsius/Fahrenheit) switchable
12. Comfort dashboard
FEATURES
1. LED indicator
2. Battery compartment cover
3. Hang hole for wall mounting
4. Channel slide switch
5. A hole for hanging strip
1
2
3
4
5
CH3CH2CH1
06
Press▲/CHbutton to check the outdoor temperature and
humidity of channel 1/2/3. When you switch to the mode,
the display will automatically loop 3 sensor data.
If you want to reset all the data of sensors , press and hold
▲/CHbutton 3 seconds, and it will reconnect with the
sensors.
CHANNEL SETTING
Press and holdSETbutton, to enter the SETTING MODE,
once in SETTING MODE the preference you are currently
setting will blink on the middle of the display.
During setting, only the setting figure will display, other
parts will be invisible.
To adjust the currently flashing item, press ▲/CH or
▼/MEM buttons (press and hold to fast adjust).
To save your adjustments, press and release theSET
button to adjust the next preference. (The setting will be
automatically save and exit if there is no operation within 20
seconds.)
The preference set order is as follows:
KEY TONE ON/OFF
TIME FORMAT 12/24H
CLOCK HOUR
CLOCK MINUTE
CALENDAR YEAR
CALENDAR DATE FORMAT (MONTH-DAY or DAY-MONTH)
CALENDAR MONTH
FUNTIONS SETTING MODE
13. Low battery indicator
14. Key tone on/off
15. Transmission range: up to 100 meters/330 feet in open area
16. 3-mode brightness: Bright/Dim/Off
17. Support desk standing or wall hanging
07
When the base station powered with batteries only, touch
SNOOZE/LIGHT for 1 second at the top, momentarily
light up the screen for 20 seconds.
When powered by adapter, touchSNOOZE/LIGHT to
adjust the brightness BRIGHT-DIM-OFF.
TOUCH ADJUSTABLE BACKLIGHT
The alarm sound will last for 2 minutes then be canceled
automatically. It will make sound as follow:
0-10 seconds: Beep per second
11-20 seconds: Beep x 2 per second
21-30 seconds: Beep x 4 per second
31-120 seconds: Keep BI sound
SNOOZE SETTING
Press ALARM button to turn ON/OFF the alarm. If the alarm
is on, the alarm icon will located between hour and minute;
If the alarm is off, the alarm icon will disappear. It will return to
normal time display mode if no operation in 5 seconds.
Press and hold ALARM button to enter ALARM CLOCK
MODE.
Once in ALARM CLOCK MODE the preference you are
currently setting will blink on the screen.
To adjust the currently flashing item, press▲/CHor
▼/MEMbuttons (press and hold to fast adjust).
To save your adjustments, press and release theALARM
button to adjust the next preference. (The setting will be
automatically save and exit if there is no operation within 20
seconds.)
ALARM CLOCK SETTING
08
CALENDAR DATE
C/F (CELSIUS/FAHRENHEIT)
To snooze the alarm, press SNOOZE/LIGHT button to enter
into SNOOZE MODE for 5 minutes, the snooze icon will
display.
To stop the alarm, press any other button, but sounds again if
the alarm condition reoccurs.
To deactivate the alarm, pressALARMbutton to turn it off.
1. When battery-powered base station is lower than 3.6V, or
when the power for remote sensor is lower than 2.5V, the
low battery indicator will display on the screen, it indicate
that it's time to change the batteries.
2. When it is powered by DC adapter, the batteries could
memory the time and date, even though the base station
power off, the memorized setting would not be reset.
3. To avoid the power runs out, the batteries getting rotten and
damage the units, please change batteries on time when
low battery reminder show up.
4. Please use alkaline dry batteries, do not use rechargeable
batteries.
LOW BATTERY ALERT
Press▼/MEM button to check the MAX/MIN temperature
and humidity record for 3 channel sensor, the preference set
order is as follows:
Maximum temperature & humidity
Minimum temperature & humidity
Current temperature & humidity
The records will be cleared automatically at 00:00 everyday, or
manually cleared by press and hold▼/MEMbutton.
MAX/MIN RECORD
09
Weather forecast in 12+ Hour: Sunny, Partly Cloudy, Cloudy,
RainySnowy.
The weather forecast is based on collecting hourly
temperature & humidity from the outdoor sensor . The forecast
station predict weather conditions for the next 12 hours with
70-75% accuracy.
The default weather icon is partly cloudy, the base station will
calibrate the weather report in 1-2 weeks with the outdoor
temperature and humidity data .
The remote sensor should be place outside to get accurate
outdoor data or it will effect the accurate of weather forecast.
When the remote sensor detects the temperature drop to
0-2.9 °C (32-37.2 °F), the snow icon will flash; when
temperature value is lower than 0, the snow icon will
keep display at the top of weather forecast.
LOW TEMPERATURE ALERT
WEATHER FORECAST
WEATHER
ICON
Description Sunny Partly
Cloudy Cloudy Rainy Snowy
COMFORT INDEX
Comfort Index
Dry
Good
Wet
Humidity Range
1-40%
41-75%
76%
10
The trend icon will display when the temperature increase
1compared to last data, or increase 1 in 1 hour;
The trend icon will display when the humidity value
increase 3% compared to last data, or increase 3% in 1 hour.
Vice the verse for decrease trends.
When the increase/decrease is less then 1 or 3% in 1 hour,
the trend icon will not display.
TRENDS
TROUBLE SHOOTING
Problem Solution
1. Make sure the base station is
powered on
2. Make sure the sensor installed the
batteries
3. If there is no sensor signal received
in 3 minutes, the base station will
stop receiving the signal. Press and
hold▲/CHbutton for 2 seconds
to re-synchronize the sensor.
4. Try to turn off/remove away from
other existing wireless equipment.
5. Replace new batteries.
When you uninstall the sensor or switch
to the other channel, the signal of
previous sensor will become weaker but
won’t disappear immediately, it will clear
the data and display “--.-” or
re-synchronize the new sensor data
next hour until the signal gone
--.-
(No data shown
on outdoor
dashboard)
Uninstall the
sensor or switch
the channel
number on the
sensor, there is
no change.
11
SPECIFICATION
UNIT
BASIC SPECS
TEMPERATURE RANGE HUMIDITY RANGE
- 9,9 50
- 40 60
Show HH.H
when base station >50
(122 ), or remote sensors
>60 (140)
Show LL.L
when base station <-9.9
(14 ) or remote sensors <
-40 / (-40)
Show HH >99%RH
Show LL<1%RH
BASE
STATION
Sensor Transmission
Frequency
Alimentazione della
stazione base
Signal Transmission
Distance
3 x 1.5V type AAA alkaline batteries
& 5V 1.2A DC Adapter (Included)
Compatible with <0.3cm diameter screw
REMOTE
SENSORS
1%RH99%RH
1%RH99%RH
OUT OF
RANGE
● ●
433.92MHz
300ft (100m) in open area
IP54
Waterproof Rating
Sensor Hanging Hole
12
For better accuracy of product, please place the sensor lengthwise/
standing up and at least 5~ 6.5 feet (1.5~2 meters) away from the
ground. Avoid exposing the sensor to direct sunlight for a long time.
WETTERSTATION
BEDIENUNGSANLEITUNG
Bitte lesen Sie diese Anleitung sorgfältig und bewahren Sie sie für
späteres Nachschlagen auf.
Bei Fragen zu dem Produkt schreiben Sie an support@iraddy.com oder
schauen auf www.iraddy.com vorbei.
WF-55C
VOR BENUTZUNG BITTE AUFMERKSAM LESEN!
WICHTIGE MONTAGEHINWEISE
PACKUNGSINHALT
INSTALLATION
ÜBERSICHT
EIGENSCHAFTEN
KANALEINSTELLUNG
FUNKTIONSEINSTELLUNG
TOUCH EINSTELLUNG BELEUCHTUNG
ALARMEINSTELLUNG
SCHLUMMER
NIEDRIGER LADESTAND DER BATTERIE
MAX/MIN-WERTE
WETTERVOERHERSAGE
KOMFORTINDEX
NIEDRIGER TEMPERATURALARM
TRENDS
FEHLERSUCHE
SPEZIFIKATION
INHALTSVERZEICHNIS
13
13
14
14
16
18
19
19
20
20
20
21
21
22
22
23
23
24
25
VOR BENUTZUNG BITTE AUFMERKSAM LESEN!
WICHTIGE MONTAGEHINWEISE
Reinigen Sie das Produkt nicht mit Benzin, Verdünnung oder
anderen scharfen Chemikalien. Wenn nötig, nutzen Sie ein
weiches Tuch zur Reinigung.
Zerlegen oder demontieren Sie das Gerät nicht, es sind keine
vom Nutzer zu wartenden Teile darin.
Das Produkt niemals in Wasser tauchen, dies führt zu
irreparablen Schäden.
Setzen Sie das Gerät keiner Gewalt oder Stößen aus und
bewahren. Sie es vor hohen Temperaturen oder hoher
Luftfeuchtigkeit.
Bitte zweckentfremden oder manipulieren Sie das Gerät
niemals.
Niemals neue und verbrauchte Batterien zusammen
verwenden.
Mischen Sie keine unterschiedlichen Batterietypen (Alkaline,
Standard oder Wiederuafladbar).
Entfernen Sie die Batterien bei Nichtbenutzung, anderenfalls
könnten auslaufende Batterien zu Schäden führen.
Entsorgen Sie das Gerät nicht mit dem Hausmüll sondern
bringen. Sie es zu einer entsprechenden Sammelstelle.
Die Basisstation nicht Regen oder Feuchtigkeit aussetzen,
Die Reichweite des Sensorsenders hängt von den
Umgebungsbedingungen ab und kann stark schwanken (z.B.
verringern Betonwände die Reichweite sehr viel stärker als
z.B. eine Rigipswand).
Montieren Sie den Sensor ausschließlich vertikal, damit evtl.
Entstehende Feuchtigkeit hinauslaufen kann. Niemals im
prallen Sonnenlicht montieren und sorgen Sie für eine gute
Belüftung des Sensors.
13
1. Basisstation und Sensor sollten mindestens 1,5m bis 2m
von Störquellen wie z.B. Fernsehern, Computern,
WLAN-Stationen etc entfernt montiert werden.
PACKUNGSINHALT
1 x Wetterstation
1 x Funksensor
1 x Bedienungsanleitung
1 x DC-Netzgerät
* Alkaline Batterien sind nicht enthalten!
Sensorsetup
INSTALLATION
Die Basisstation unterstützt max 3 verschiedene Sensorkanäle.
Der entsprechende Schalter befindet sich im Batteriefach, hat
die Positionen 1 bis 3 und muss die gleiche Stellung aufweisen
wie der korrespondierende Schalter im Sensorsender. Das
Einsetzen von 2x AA Batterien oder Akkus aktiviert den Sender.
321
14
2. Halten Sie die Basisstation von Metall-Fensterrahmen fern,
dies könnte den Empfang stören.
3. Verwenden Sie keine Geräte wie z..B schnurlosen
Mikrofone oder Kopfhörer, die auf der gleichen Frequenz
arbeiten. (433.92MHz) Nachbarn, die solche Geräte auf der
gleichen Frequenz betreiben, könnten ebenfalls Störungen
verursachen.
4. Platzieren Sie die Basisstation in einer trockenen und
staubfreien Umgebung. Um eine korrekte
Temperaturmessung sicherzustellen, platzieren Sie weder
Sensor noch Basisstation in direktem Sonnenlicht oder
neben Wärme- und Hitzequellen.
LR03/R03 AAA 1.5V
+_
LR03/R03 AAA 1.5V
+_
Basisstationsetup
Entfernen Sie die Schutzfolie vom Display der Basisstation.
Stecken Sie das Netzgerät in eine Steckdose und verbinden
Sie es mit der Basisstation. Alternativ können Sie auch
Batterien verwenden. Sie können auch Batterien und Netzgerät
gleichzeitig verwenden, in diesem Falle bleiben die
Einstellungen und Messwerte nach einer Netztrennung
erhalten.
Die Basisstation kan entweder aufrecht hingestellt oder an die
Wand montiert werden.
Sensor Und Basisstation Verbinden
1. Batterien im Sensorsender einsetzen und den Sendekanal
(1,2,3) wählen.
2. Stecken Sie das Netzgerät der Basisstation ein. Es kann bis
zu 3 Minuten dauern, bis die Basisstation den Sensor
empfängt.
3. Sobald die rote LED am Sensor zweimal blinkt und Sie die
Wetterdaten auf dem Display der Wetterstation sehen
können, haben sich Sensor und Basisstation erfolgreich
verbunden.
4. When the red indicator of sensor flash for once per minute,
it indicates that it is updating the sensor data to base station.
Die rote LED blinkt dann ca. einmal pro Minute, dies
bedeutet, dass Daten an die Basisstation gesendet werden.
Beispiel: wenn Sie Kanal 1 am Sensor eingestellt haben,
werden auch die Wetterdaten von Sensor 1 auf dem Display
der Basisstation angezeigt.
15
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61

Raddy WF-55C Manuel utilisateur

Catégorie
Stations météo
Taper
Manuel utilisateur

dans d''autres langues