ARTHUR MARTIN ELECTROLUX AW6T7242AF Manuel utilisateur

Catégorie
Machines à laver
Taper
Manuel utilisateur
AW6T7242AF
EN Washing Machine User Manual 2
FR Lave-linge Notice d'utilisation 31
CONTENTS
Safety information 2
Safety instructions 4
Product description 5
Control panel 6
Dial and buttons 8
Programmes 10
Settings 14
Before first use 15
Daily use 15
Hints and tips 19
Care and cleaning 20
Consumption values 25
Troubleshooting 25
Technical Data 28
Quick guide 29
Subject to change without notice.
SAFETY INFORMATION
Before the installation and use of the appliance, carefully
read the supplied instructions. The manufacturer is not
responsible for any injuries or damage that are the result of
incorrect installation or usage. Always keep the instructions
in a safe and accessible location for future reference.
Children and vulnerable people safety
This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
the use of the appliance in a safe way and understand the
hazards involved.
Children between 3 and 8 years of age and persons with
very extensive and complex disabilities shall be kept away
from the appliance unless continuously supervised.
Children of less than 3 years of age should be kept away
from the appliance unless continuously supervised.
Do not let children play with the appliance.
Keep all packaging away from children and dispose of it
appropriately.
Keep detergents away from children.
Keep children and pets away from the appliance when the
door is open.
If the appliance has a child safety device, it should be
activated.
2
Children shall not carry out cleaning and user maintenance
of the appliance without supervision.
General Safety
Do not change the specification of this appliance.
This appliance is intended to be used in household and
similar applications such as:
staff kitchen areas in shops, offices and other working
environments;
by clients in hotels, motels, bed & breakfast and other
residential type environments;
areas for communal use in blocks of flats or in
launderettes.
Do not exceed the maximum load of 7 kg (refer to the
"Programme chart" chapter).
The operating water pressure at the water entry point from
the outlet connection must be between 0.5 bar (0.05 MPa)
and 8 bar (0.8 MPa).
The ventilation opening in the base must not be covered
by a carpet, mat, or any floor covering.
The appliance must be connected to the water mains using
the new supplied hose sets, or other new hose sets
supplied by the Authorised Service Centre.
Old hose sets must not be reused.
If the mains power supply cable is damaged, it must be
replaced by the manufacturer, its Authorised Service
Centre or similarly qualified persons to avoid an electrical
hazard.
Before any maintenance operation, deactivate the
appliance and disconnect the mains plug from the socket.
Do not use high pressure water sprays and/or steam to
clean the appliance.
Clean the appliance with a moist cloth. Use only neutral
detergents. Do not use abrasive products, abrasive
cleaning pads, solvents or metal objects.
3
SAFETY INSTRUCTIONS
Installation
The installation must comply
with relevant national
regulations.
Remove all the packaging and the
transit bolts including rubber bush with
plastic spacer.
Keep the transit bolts in a safe place. If
the appliance is to be moved in the
future they must be reattached to lock
the drum to prevent an internal
damage.
Always take care when moving the
appliance as it is heavy. Always use
safety gloves and enclosed footwear.
Follow the installation instructions
supplied with the appliance.
Do not install or use a damaged
appliance.
Do not install or use the appliance
where the temperature can be less
than 0°C or where it is exposed to the
weather.
The floor area on which the appliance
is to be installed must be flat, stable,
heat resistant and clean.
Make sure that there is air circulation
between the appliance and the floor.
When the appliance is in its permanent
position, check if it is levelled correctly
with the aid of a spirit level. If it is not,
adjust the feet accordingly.
Do not install the appliance directly
above a floor drain.
Do not spray water on the appliance
and do not expose it to excessive
humidity.
Do not install the appliance where the
appliance lid cannot be fully opened.
Do not put a closed container to collect
possible water leakage under the
appliance. Contact the Authorised
Service Centre to ensure which
accessories can be used.
Electrical connection
WARNING! Risk of fire and
electric shock.
The appliance must be earthed.
Always use a correctly installed
shockproof socket.
Make sure that the parameters on the
rating plate are compatible with the
electrical ratings of the mains power
supply.
Do not use multi-plug adapters and
extension cables.
Make sure not to cause damage to the
mains plug and to the mains cable.
Should the mains cable need to be
replaced, this must be carried out by
our Authorised Service Centre.
Connect the mains plug to the mains
socket only at the end of the
installation. Make sure that there is
access to the mains plug after the
installation.
Do not touch the mains cable or the
mains plug with wet hands.
Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
Water connection
Do not cause damage to the water
hoses.
Before connection to new pipes, pipes
not used for a long time, where repair
work has been carried out or new
devices fitted (water meters, etc.), let
the water flow until it is clean and clear.
Ensure that there are no visible water
leaks during and after the first use of
the appliance.
Do not use an extension hose if the
inlet hose is too short. Contact the
Authorised Service Centre for the
replacement of the inlet hose.
When unpacking the appliance, It is
possible to see water flowing from the
drain hose. This is due to the testing of
4
the appliance with the use of water in
the factory.
You can extend the drain hose to
maximum 400 cm. Contact the
Authorised Service Centre for the other
drain hose and the extension.
Make sure that there is access to the
tap after the installation.
Use
WARNING! Risk of injury,
electric shock, fire, burns or
damage to the appliance.
Follow the safety instructions on the
detergent packaging.
Do not put flammable products or items
that are wet with flammable products
in, near or on the appliance.
Do not wash fabrics which are heavily
soiled with oil, grease or other greasy
substances. It can damage rubber
parts of the washing machine. Prewash
such fabrics by hand before loading
them into the washing machine.
Make sure that all metal objects are
removed from the laundry.
Service
To repair the appliance contact the
Authorised Service Centre.
Use original spare parts only.
Disposal
WARNING! Risk of injury or
suffocation.
Disconnect the appliance from the
mains electrical and water supplies.
Cut off the mains electrical cable close
to the appliance and dispose of it.
Remove the door catch to prevent
children or pets from becoming trapped
in the drum.
Dispose of the appliance in accordance
with local requirements for the disposal
of Waste Electrical and Electronic
Equipment (WEEE).
PRODUCT DESCRIPTION
Special features
Your new washing machine meets all
modern requirements for an effective
treatment of laundry with low water,
energy and detergent consumption and
will care for fabrics.
Thanks to the Soft Plus option, the
fabric softener is uniformly spread out
in the laundry and deeply penetrates
the fabric fibres favouring a perfect
softness.
The SensiCare System automatically
adjusts the programme duration to the
laundry in the drum to achieve perfect
washing results in the minimum
possible time.
5
Appliance overview
2
3
1
4
5
6
1
Control panel
2
Lid
3
Lid handle
4
Drain pump filter
5
Feet for levelling the appliance
6
Rating plate
CONTROL PANEL
Control panel description
2 3 4 5
10
7
1
68911
1
Programme dial
2
Display
3
Delay Start touch button
4
Time Manager touch button
5
Start/Pause touch button
6
Soft Plus touch button
7
Extra Rinse touch button
8
Prewash touch button
9
Spin reduction options touch button
No Spin option
Rinse Hold option
Nuit option
6
10
On/Off push button
11
Temperature touch button
Display
A B C D
E
FG
A Lid locked indicator.
B Delay start indicator.
C The digital indicator can show:
Programme duration (e. g. ).
Delay time (e. g. ).
Cycle end ( ).
Warning code (e.g. ).
D Time Manager bars level indicator.
E Drum clean indicator.
F Child safety lock indicator.
G Add garments indicator. Illuminates at the beginning of the
Wash phase, while the user can still pause the appliance and
add more laundry.
7
DIAL AND BUTTONS
Introduction
The options/functions are not
available with all washing
programmes. Check the
compatibility between options/
functions and washing
programmes in the
"Programme Chart". An option/
function can exclude another
one, in this case the appliance
doesn't allow you to set
incompatible options/functions.
On/Off
Press this button for a few seconds to
activate or deactivate the appliance. Two
different tunes sound while switching the
appliance on or off.
As the Stand-by function automatically
deactivates the appliance after several
minutes to reduce the energy
consumption, you may need to activate
the appliance again.
For more details, refer to Stand-by
paragraph in Daily Use chapter.
Temperature
When you select a washing programme,
the appliance automatically proposes a
default temperature.
The indicator Cold = cold water.
The indicator of the set temperature
comes on.
Spin
When you set a programme, the appliance
automatically sets the maximum spin
speed allowed except programme Denim.
Additional spin options:
No Spin
. The related indicator
comes on.
Set this option to deactivate all spin
phases. The appliance performs only
the draining phase of the selected
washing programme. Set this option for
very delicate fabrics. The rinse phase
uses more water for some washing
programmes
Rinse Hold . The related indicator
comes on.
The final spin is not performed. The
water of the last rinse is not drained out
to prevent the fabrics from creasing.
The washing programme ends with
water in the drum.
The lid stays locked and the drum turns
regularly to reduce creasing. You must
drain the water to unlock the lid.
If you touch the Start/Pause button,
the appliance performs the spinning
phase and drains the water.
Nuit . The related indicator comes
on.
The intermediate and the final spinning
phases are suppressed and the
programme ends with water in the
drum. This helps to reduce creasing.
The lid stays locked. The drum turns
regularly to reduce creasing. You must
drain the water to unlock the lid.
As the programme is very quiet, it is
suitable for use at night time when
cheaper electricity tariffs are available.
In some programmes the rinses are
performed with more water.
If you touch the Start/Pause
button,
the appliance performs only the
draining phase.
The appliance empties the
water out automatically after
approximately 18 hours.
Prewash
With this option you can add a prewash
phase to a washing programme.
The relevant indicator illuminates.
Use this option to add a pre-wash
phase at 30 °C before the washing
phase.
8
This option is recommended for heavily
soiled laundry, especially if containing
sand, dust, mud and other solid
particles.
These options can increase the
programme duration.
Permanent Extra Rinse
With this option you can add a few rinses
according to the selected washing
programme.
Use this option for people with allergies to
detergent residues and with sensitive skin.
This option increases the
programme duration.
The corresponding indicator above the
touch button illuminates and also stays
permanently on during next cycles until
this option is deactivated.
Permanent Soft Plus
Set this option to optimise the fabric
softener distribution and improve fabric
softness.
Recommended when you use fabric
softener.
This option increases the
programme duration.
The corresponding indicator above the
touch button illuminates and also stays
permanently on during next cycles until
this option is deactivated.
Delay Start
With this option you can delay the start of
a programme to a more convenient time.
Touch the button repeatedly to set the
required delay. The time increases in
steps of 1 hour up to 20 hours.
The display shows the indicator
and
the selected delay time. After touching the
Start/Pause button, the appliance
begins the countdown and the lid is
locked.
Time Manager
With this option you can reduce the
programme duration depending on the
load size and the degree of soiling.
When you set a washing programme, the
display shows the default duration and
dashes.
Touch Time Manager button to reduce
the programme duration according to your
needs. The display shows the new
programme duration and a number of
dashes will decrease accordingly:
suitable for a full load of normally
soiled garments.
a quick cycle for a full load of lightly
soiled garments.
very quick cycle for a smaller lightly
soiled load (max. half load
recommended).
the shortest cycle to freshen up a
small amount of laundry.
The Time Manager is available only with
the programmes in the table.
indicator
Coton
Coton Eco
Synthétiques
1)
1)
Default duration for all programmes.
9
Start/Pause
Touch the Start/Pause button to start,
pause the appliance or interrupt a running
programme.
PROGRAMMES
Programme Chart
Programme
Default tem‐
perature
Temperature
range
Refer‐
ence
spin
speed
Spin
speed
range
[rpm ]
Maxi‐
mum
load
Programme description
(Type of load and soil level)
Coton
40 °C
90 °C - Cold
1200 rpm
(1200-
400)
7 kg White cotton and coloured cotton. Normal and
heavy soil.
Coton Eco
1)
40 °C
60 °C - 40 °C
1200 rpm
(1200-
400)
7 kg White cotton and fast-coloured cotton. Normal
soil. The energy consumption decreases and the
time of the washing programme is extended, en‐
suring good washing results.
Synthétiques
40 °C
60 °C - Cold
1200 rpm
(1200 -
400)
3 kg Synthetic items or mixed fabric items. Normal
soil.
Délicats
30 °C
40 °C - Cold
1200 rpm
(1200-
400)
2 kg Delicate fabrics such as acrylics, viscose and
mixed fabrics requiring gentler washing. Nor‐
mal soil.
Rapide 14min
30 °C
800 rpm
(800-
400)
2 kg Synthetic and mixed fabric items. Light soil and
items to freshen up.
Rinçage
1200 rpm
(1200-
400)
7 kg All fabrics, except woollens and very delicate
fabrics. Programme for rinsing and spinning the
laundry. The default spin speed is the one used
for cotton programmes. Reduce the spin speed
accordingly to the type of laundry. If necessary,
set the Extra Rinse option to add rinses. With a
low spin speed, the appliance performs delicate
rinses and a short spin.
10
Programme
Default tem‐
perature
Temperature
range
Refer‐
ence
spin
speed
Spin
speed
range
[rpm ]
Maxi‐
mum
load
Programme description
(Type of load and soil level)
Essorage/
Vidange
1200 rpm
(1200
-400)
7 kg To spin the laundry and to drain the water in the
drum. All fabrics, except woollens and delicate
fabrics.
Anti-allergie
60 °C
1200 rpm
(1200 -
400)
7 kg White cotton items. This programme removes
micro-organisms thanks to a washing phase with
the temperature maintained above 60°C for sever‐
al minutes. This helps remove germs, bacteria, mi‐
cro-organism and particles. An additional rinsing
phase ensures a proper removal of detergent resi‐
dues and pollens/allergenic items. In this way the
wash is more effective.
Bébé
40 °C
40 °C - Cold
1200 rpm
(1200 -
400)
1,5 kg Delicate cycle suitable for baby's articles. High
water level and delicate movement in washing
phase protects colours and fibres.
Soie
30 °C
800 rpm
(800 -
400)
1 kg Special programme for silk and mixed synthetic
items.
Laine
40 °C
40 °C - Cold
1200 rpm
(1200-
400)
1 kg Machine washable wool, hand washable wool
and other fabrics with «hand washing» care sym‐
bol
2)
.
Sport
30 °C
40 °C - Cold
1200 rpm
(1200 -
400)
3 kg Mixed fabric sportswear. Light soil items or
items to refresh.
11
Programme
Default tem‐
perature
Temperature
range
Refer‐
ence
spin
speed
Spin
speed
range
[rpm ]
Maxi‐
mum
load
Programme description
(Type of load and soil level)
Outdoor
30 °C
40 °C - Cold
1200 rpm
(1200-
400)
2,5
kg
3)
1 kg
4)
Do not use fabric softener and
make sure that there is no soften‐
er residue in the detergent dis‐
penser.
Synthetic sport items. This programme is de‐
signed to gently wash modern outdoor sportswear
and is also suitable for gym, cycling or jogging
clothes or similar. The recommended laundry load
is 2,5 kg.
Waterproof, waterproof-breathable and water
repellent fabrics. This programme can also be
used as a water repellency restoring cycle, specifi‐
cally tailored for treating clothes with a hydropho‐
bic coating. To perform the water repellency re‐
storing cycle, proceed as follows:
Pour the washing detergent in the compart‐
ment .
Pour a special water repellency restorer for
fabric into the softener compartment of the
drawer .
Reduce the laundry load to 1 kg.
To further improve the water re‐
pellency restoring action, dry the
laundry in a tumble dryer by set‐
ting the Outdoor drying pro‐
gramme (if available and if the
garment care label permits tum‐
ble drying).
12
Programme
Default tem‐
perature
Temperature
range
Refer‐
ence
spin
speed
Spin
speed
range
[rpm ]
Maxi‐
mum
load
Programme description
(Type of load and soil level)
Denim
30 °C
40 °C - Cold
800 rpm
(1200 -
400)
3 kg Special programme for Denim clothing with
delicate washing phase to minimize colour
fading and marks. For better care a reduced load
size is recommended.
1)
Standard programmes for the Energy Label consumption values. According to regulation 1061/2010,
these programmes are respectively the «Standard 60°C cotton programme» and the «Standard 40°C cotton pro‐
gramme». They are the most efficient programmes in terms of combined energy and water consumption for
washing normally soiled cotton laundry.
The water temperature of the washing phase may differ from the temperature declared for the se‐
lected programme.
2)
During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't rotate or
doesn't rotate properly, but this is normal for this programme.
3)
Washing programme.
4)
Washing programme and waterproofing phase.
Programme options compatibility
Programme
Coton
Coton Eco
Synthé‐
tiques
Délicats
Rapide
14min
Rinçage
Essorage/
Vidange
Anti-allergie
13
Programme
Bébé
Soie
Laine
Sport
Outdoor
Denim
Woolmark Apparel Care - Blue
The wool wash cycle of this machine has been
approved by The Woolmark Company for the
washing of wool garments labelled as «hand
wash» provided that the garments are washed
according to the instructions issued by the
manufacturer of this washing machine. Follow
the garment care label for drying and other
laundry instructions. M1145
The Woolmark symbol is a Certification mark
in many countries.
SETTINGS
Acoustic signals
This appliance has different acoustic
signals, that operate when:
You activate the appliance (special
short tune).
You deactivate the appliance (special
short tune).
You touch the buttons (click sound).
You make an invalid selection (3 short
sounds).
The programme is completed
(sequence of sounds for about 2
minutes).
The appliance has a malfunction
(sequence of short sounds for about 5
minutes).
To deactivate/activate the acoustic
signals when the programme is
completed, touch the and the
buttons simultaneously for about 2
seconds. The display shows On/Off
If you deactivate the acoustic
signals, they continue to
operate when the appliance
has a malfunction.
Child Lock
With this option you can prevent children
from playing with the control panel.
To activate/deactivate this option, hold
down the button until comes on/
goes off on the display.
The appliance will default to this option
after you switch it off.
The Child Lock function may not be
available for a few seconds after switching
the appliance on.
14
BEFORE FIRST USE
1. Make sure that the electrical power is
available and the water tap is open.
2. Pour 2 litres of water into the detergent
compartment marked by .
This action activates the drain system.
3. Pour a small quantity of detergent into
the compartment marked by .
4. Set and start a programme for cotton
at the highest temperature without any
laundry in the drum.
This removes all possible dirt from the
drum and the tub.
DAILY USE
WARNING! Refer to Safety
chapters.
Activating the appliance
1. Connect the mains plug to the mains
socket.
2. Open the water tap.
3. Press button On/Off to activate the
appliance.
A short tune sounds.
Loading the laundry
1. Open the appliance lid.
2. Push the button A.
A
The drum opens automatically.
3. Put the laundry in the drum, one item
at a time.
4. Shake the items before you put them
in the appliance.
Make sure not to put too much laundry in
the drum.
5. Close the drum and the lid.
CAUTION! Before you close
the lid of your appliance, make
sure that you close the drum
correctly.
Detergent compartments. Using
detergent and additives
1. Measure out specified detergents for
washing machine the detergent and the
fabric conditioner.
2. Put the detergent and the fabric
conditioner into the proper compartments.
Always obey the instructions
that you find on the packaging
of the detergent products.
15
Detergent compartment for pre‐
wash phase.
The marks MAX are the maxi‐
mum levels of the quantity of
detergent (powder or liquid).
Detergent compartment for
washing phase.
The marks MAX are the maxi‐
mum levels of the quantity of
detergent (powder or liquid).
Compartment for liquid additives
(fabric conditioner, starch).
The mark
M
is the maximum
level for the quantity liquid addi‐
tives.
Flap for powder or liquid deter‐
gent.
Liquid or powder detergent
1.
CLICK
2.
A
3.
CLICK
4.
B
16
Position A for powder detergent (factory setting).
Position B for liquid detergent.
When you use the liquid detergent:
Do not use gelatinous or thick liquid detergents.
Do not put more liquid then the maximum level.
Setting a programme
1. Turn the programme dial to select the
desired washing programme.
The indicator of the Start/Pause button
flashes.
The display shows an indicative
programme duration.
2. To change the temperature and/or the
spin speed, touch the related buttons.
3. If desired, set one or more options by
touching the related buttons. The
related indicators illuminate on the
display and the given information
changes accordingly.
If a selection is not possible
an acoustic signal sounds and
the display shows .
Starting a programme
Touch the Start/Pause button to start
the programme. It is not possible to start
the programme when the indicator of the
button is off and doesn't flash (e.g.
programme dial on a wrong position).
The related indicator stops flashing and
stays on.
The programme starts, the lid is locked.
The display shows the indicator
.
The drain pump can operate
shortly before the appliance fills
water.
Starting a programme with the
delay start
1. Touch the Delay Start button
repeatedly until the display shows the
desired delay time. On the display the
indicator shows .
2. Touch the Start/Pause button. The
appliance lid locks and starts the
countdown of the delay start. The display
shows the indicator .
When the countdown is completed, the
programme starts automatically.
Cancelling the delay start after
the countdown has started
To cancel the delay start:
1. Touch the Start/Pause button to
pause the appliance. The related
indicator flashes.
2. Touch the Delay Start button
repeatedly until the display shows
and the indicator goes off.
3. Touch the Start/Pause button
again to start the programme
immediately.
Changing the delay start after
the countdown has started
To change the delay start:
1. Touch the Start/Pause button to
pause the appliance. The related
indicator flashes.
2. Touch the Delay Start
button
repeatedly until the display shows the
desired delay time.
3. Touch the Start/Pause button
again to start the new countdown.
The SensiCare System load
detection
After touching the Start/Pause button:
1. The SensiCare System starts
estimating the weight of the load to
17
calculate the real programme duration.
During this phase the Time Manager
bars placed below the time digits
play a simple animation.
2. After about 15-20 minutes the Time
Manager bars disappear and new
cycle duration is displayed.
The appliance automatically adjusts
the programme duration to the load to
achieve perfect washing results in the
minimum possible time.
Interrupting a programme and
changing the options
When the programme is running, you can
change only some options:
1. Touch the button Start/Pause .
The related indicator flashes.
2. Change the options. The given
information in the display changes
accordingly.
3. Touch the button Start/Pause
again.
The washing programme continues.
Cancelling a running
programme
1. Press the button On/Off to cancel the
programme and to deactivate the
appliance.
2. Press the button On/Off again to
activate the appliance.
If the SensiCare System has
completed and the water filling
has already started, the new
programme starts without
repeating the SensiCare
System. The water and the
detergent are not drained out in
order to avoid waste.
There is also an alternative way of
cancelling:
1. Rotate the selector knob to the "Reset"
position .
2. Wait for 1 second. The display shows
.
Now, you can set a new washing
programme.
Opening the lid - Adding
garments
If the temperature and level of
the water in the drum are too
high and/or the drum is still
rotating you should not open
the lid.
While a programme or the delay start
operates, the appliance lid is locked. The
display shows the indicator
.
1. Touch the Start/Pause
button. The
indicator
starts flashing.
2. Wait until the lid lock indicator
stops flashing and goes off. Open the
appliance lid and drum doors. If
necessary, add or remove the items.
Close the drum door and lid. Touch the
Start/Pause button. The
programme or the delay start
continues.
End of the programme
When the programme has finished, the
appliance stops automatically. The
acoustic signals operate (if they are
active). The display shows
The indicator of the Start/Pause button
goes off.
The lid unlocks and the indicator
goes
off.
1. Press button On/Off to deactivate the
appliance.
After five minutes from the end of the
programme, the energy saving function
automatically deactivates the appliance.
When you activate the
appliance again, the display
shows the end of the previous
programme. Turn the
programme dial to set a new
cycle.
18
2. Remove the laundry from the
appliance.
3. Make sure that the drum is empty.
4. Keep the lid and the detergent
dispenser slightly ajar to prevent
mildew and odours.
5. Close the water tap.
Draining water out after end of
cycle
If you have chosen a programme or an
option that does not empty out the water
of the last rinse, the programme is
completed, but:
The time area shows and the
display shows the lid locked .
The drum still turns at regular intervals
to prevent creases in the laundry.
The lid stays locked.
You must drain the water to open the
lid:
1. Press the Start/Pause button:
2. When the programme is completed
and the lid locked indicator goes
off, you can open the lid.
3. Press the On/Off button for a few
seconds to deactivate the appliance.
Stand-by option
The Stand-by function automatically
deactivates the appliance to reduce the
energy consumption when:
You do not use the appliance for 5
minutes .
Press the button On/Off to activate the
appliance again.
5 minutes after the end of the washing
programme
Press the On/Off button to activate the
appliance again.
The display shows the end of the last
programme.
Turn the programme dial to set a new
cycle.
If the dial is rotated to the "Reset" position
, the appliance automatically turns off in
30 seconds.
If you set a programme or an
option that ends with water in
the drum, the Stand-by function
doesn't deactivate the
appliance to remind you to
drain the water.
HINTS AND TIPS
WARNING! Refer to Safety
chapters.
The laundry load
Divide the laundry into: white, coloured,
synthetics, delicates and wool.
Follow the washing instructions on the
laundry care labels.
Do not wash white and coloured items
together.
Some coloured items can discolour
with the first wash. We recommend that
you wash them separately for the first
couple of times.
Turn multilayered fabrics, wool and
items with printed illustrations inside
out.
Pre-treat tough stains.
Wash heavy soil stains with a special
detergent.
Be careful with curtains. Remove the
hooks and put the curtains in a washing
bag or pillowcase.
Do not wash laundry without hems or
with cuts. Use a washing bag to wash
small and/or delicate items (e.g.
underwired bras, belts, tights,
shoelaces, ribbons, etc. ).
A very small load can cause balance
problems with the spin phase leading to
excessive vibration. If this occurs:
a. interrupt the programme and open
the door (refer to "Daily Use"
chapter);
b. manually redistribute the load so
that the items are spaced evenly
around the tub;
19
c. press the Start/Pause button. The
spin phase continues.
Button up pillowcases, close zippers,
hooks and poppers. Tie up belts, cords,
shoelaces, ribbons and any other loose
elements.
Empty pockets and unfold the items.
Stubborn stains
For some stains, water and detergent is
not sufficient.
We recommend that you pre-treat these
stains before you put the items in the
appliance.
Special stain removers are available. Use
the special stain remover that is applicable
to the type of stain and fabric.
Detergents and other treatments
Only use detergents and other
treatments specially made for washing
machines:
powder detergents for all types of
fabric, excluding delicate. Prefer
powder detergents containing
bleach for whites and laundry
sanitization
liquid detergents, preferably for low
temperature wash programmes (60
°C max) for all types of fabric, or
special ones for woollens only.
Do not mix different types of
detergents.
To help the environment, do not use
more than the recommended quantity
of detergent.
Follow the instructions that you find on
packaging of the detergents or other
treatments without exceeding the
indicated maximum level ( ).
Use the recommended detergents for
the type and colour of the fabric, the
programme temperature and the level
of soil.
Ecological hints
Set a programme without the prewash
phase to wash laundry with normal soil.
Always start a washing programme
with the maximum load of laundry
allowed.
If you pre-treat the stains or use a stain
remover, set a programme with a low
temperature.
To use the correct quantity of
detergent, check the water hardness of
your domestic system. Refer to "Water
hardness".
Water hardness
If the water hardness in your area is high
or moderate, we recommend that you use
a water softener for washing machines. In
areas where the water hardness is soft it
is not necessary to use a water softener.
To find out the water hardness in your
area, contact your local water authority.
Use the correct quantity of water softener.
Follow the instructions that you find on the
packaging of the product.
CARE AND CLEANING
WARNING! Refer to Safety
chapters.
External cleaning
Clean the appliance with mild soap and
warm water only. Fully dry all the surfaces.
CAUTION! Do not use alcohol,
solvents or chemical products.
CAUTION! Do not clean the
metal surfaces with chlorine-
based detergent.
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64

ARTHUR MARTIN ELECTROLUX AW6T7242AF Manuel utilisateur

Catégorie
Machines à laver
Taper
Manuel utilisateur

dans d''autres langues