AEG IAE64423FB Manuel utilisateur

Catégorie
Plaques de cuisson
Taper
Manuel utilisateur
USER
MANUAL
EN User Manual 2
Hob
FR Notice d'utilisation 24
Table de cuisson
DE Benutzerinformation 50
Kochfeld
IAE64423FB
CONTENTS
1. SAFETY INFORMATION.............................................................................................2
2. SAFETY INSTRUCTIONS.............................................................................................4
3. INSTALLATION............................................................................................................7
4. PRODUCT DESCRIPTION...........................................................................................9
5. DAILY USE..................................................................................................................11
6. HINTS AND TIPS........................................................................................................16
7. CARE AND CLEANING.............................................................................................19
8. TROUBLESHOOTING............................................................................................... 19
9. TECHNICAL DATA.................................................................................................... 22
10. ENERGY EFFICIENCY.............................................................................................23
FOR PERFECT RESULTS
Thank you for choosing this AEG product. We have created it to give you
impeccable performance for many years, with innovative technologies that help
make life simpler – features you might not find on ordinary appliances. Please
spend a few minutes reading to get the very best from it.
Visit our website for:
Get usage advice, brochures, trouble shooter, service and repair information:
www.aeg.com/support
Register your product for better service:
www.registeraeg.com
Buy Accessories, Consumables and Original spare parts for your appliance:
www.aeg.com/shop
CUSTOMER CARE AND SERVICE
Always use original spare parts.
When contacting our Authorised Service Centre, ensure that you have the
following data available: Model, PNC, Serial Number.
The information can be found on the rating plate.
Warning / Caution-Safety information
General information and tips
Environmental information
Subject to change without notice.
1.
SAFETY INFORMATION
Before the installation and use of the appliance,
carefully read the supplied instructions. The
manufacturer is not responsible for any injuries or
damage that are the result of incorrect installation or
www.aeg.com
2
usage. Always keep the instructions in a safe and
accessible location for future reference.
1.1 Children and vulnerable people safety
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning the use of the appliance in a
safe way and understand the hazards involved.
Children between 3 and 8 years of age and persons
with very extensive and complex disabilities shall be
kept away from the appliance unless continuously
supervised.
Children of less than 3 years of age should be kept
away from the appliance unless continuously
supervised.
Do not let children play with the appliance.
Keep all packaging away from children and dispose of
it appropriately.
Keep children and pets away from the appliance when
it operates or when it cools down. Accessible parts
become hot during use.
If the appliance has a child safety device, it should be
activated.
Children shall not carry out cleaning and user
maintenance of the appliance without supervision.
1.2
General Safety
WARNING: The appliance and its accessible parts
become hot during use. Care should be taken to
avoid touching heating elements.
WARNING: Unattended cooking on a hob with fat or
oil can be dangerous and may result in fire.
NEVER try to extinguish a fire with water, but switch
off the appliance and then cover flame e.g. with a lid
or a fire blanket.
ENGLISH
3
CAUTION: The appliance must not be supplied
through an external switching device, such as a timer,
or connected to a circuit that is regularly switched on
and off by a utility.
CAUTION: The cooking process has to be supervised.
A short term cooking process has to be supervised
continuously.
WARNING: Danger of fire: Do not store items on the
cooking surfaces.
Metallic objects such as knives, forks, spoons and lids
should not be placed on the hob surface since they
can get hot.
Do not use the appliance before installing it in the
built-in structure.
Do not use a steam cleaner to clean the appliance.
After use, switch off the hob element by its control
and do not rely on the pan detector.
If the glass ceramic surface / glass surface is cracked,
switch off the appliance and unplug it from the mains.
In case the appliance is connected to the mains
directly using junction box, remove the fuse to
disconnect the appliance from power supply. In either
case contact the Authorised Service Centre.
If the supply cord is damaged, it must be replaced by
the manufacturer, an authorized Service or similarly
qualified persons in order to avoid a hazard.
WARNING: Use only hob guards designed by the
manufacturer of the cooking appliance or indicated by
the manufacturer of the appliance in the instructions
for use as suitable or hob guards incorporated in the
appliance. The use of inappropriate guards can cause
accidents.
2.
SAFETY INSTRUCTIONS
2.1 Installation
WARNING!
Only a qualified person must
install this appliance.
WARNING!
Risk of injury or damage to
the appliance.
Remove all the packaging.
www.aeg.com4
Do not install or use a damaged
appliance.
Follow the installation instructions
supplied with the appliance.
Keep the minimum distance from
other appliances and units.
Always take care when moving the
appliance as it is heavy. Always use
safety gloves and enclosed footwear.
Seal the cut surfaces with a sealant to
prevent moisture to cause swelling.
Protect the bottom of the appliance
from steam and moisture.
Do not install the appliance adjacent
to a door or under a window. This
prevents hot cookware falling from
the appliance when the door or the
window is opened.
Each appliance has cooling fans on
the bottom.
If the appliance is installed above a
drawer:
Do not store any small pieces or
sheets of paper that could be
pulled in, as they can damage the
cooling fans or impair the cooling
system.
Keep a distance of minimum 2 cm
between the bottom of the
appliance and parts stored in the
drawer.
Remove any separator panels
installed in the cabinet below the
appliance.
2.2 Electrical Connection
WARNING!
Risk of fire and electric
shock.
All electrical connections should be
made by a qualified electrician.
The appliance must be earthed.
Before carrying out any operation
make sure that the appliance is
disconnected from the power supply.
Make sure that the parameters on the
rating plate are compatible with the
electrical ratings of the mains power
supply.
Make sure the appliance is installed
correctly. Loose and incorrect
electricity mains cable or plug (if
applicable) can make the terminal
become too hot.
Use the correct electricity mains
cable.
Do not let the electricity mains cable
tangle.
Make sure that a shock protection is
installed.
Use the strain relief clamp on the
cable.
Make sure the mains cable or plug (if
applicable) does not touch the hot
appliance or hot cookware, when you
connect the appliance to the near
sockets.
Do not use multi-plug adapters and
extension cables.
Make sure not to cause damage to
the mains plug (if applicable) or to the
mains cable. Contact our Authorised
Service Centre or an electrician to
change a damaged mains cable.
The shock protection of live and
insulated parts must be fastened in
such a way that it cannot be removed
without tools.
Connect the mains plug to the mains
socket only at the end of the
installation. Make sure that there is
access to the mains plug after the
installation.
If the mains socket is loose, do not
connect the mains plug.
Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
Use only correct isolation devices: line
protecting cut-outs, fuses (screw type
fuses removed from the holder), earth
leakage trips and contactors.
The electrical installation must have
an isolation device which lets you
disconnect the appliance from the
mains at all poles. The isolation
device must have a contact opening
width of minimum 3 mm.
2.3 Use
WARNING!
Risk of injury, burns and
electric shock.
Remove all the packaging, labelling
and protective film (if applicable)
before first use.
This appliance is for household use
only.
ENGLISH
5
Do not change the specification of
this appliance.
Make sure that the ventilation
openings are not blocked.
Do not let the appliance stay
unattended during operation.
Set the cooking zone to “off” after
each use.
Do not rely on the pan detector.
Do not put cutlery or saucepan lids on
the cooking zones. They can become
hot.
Do not operate the appliance with
wet hands or when it has contact with
water.
Do not use the appliance as a work
surface or as a storage surface.
If the surface of the appliance is
cracked, disconnect immediately the
appliance from the power supply. This
to prevent an electrical shock.
Users with a pacemaker must keep a
distance of minimum 30 cm from the
induction cooking zones when the
appliance is in operation.
When you place food into hot oil, it
may splash.
WARNING!
Risk of fire and explosion
Fats and oil when heated can release
flammable vapours. Keep flames or
heated objects away from fats and oils
when you cook with them.
The vapours that very hot oil releases
can cause spontaneous combustion.
Used oil, that can contain food
remnants, can cause fire at a lower
temperature than oil used for the first
time.
Do not put flammable products or
items that are wet with flammable
products in, near or on the appliance.
WARNING!
Risk of damage to the
appliance.
Do not keep hot cookware on the
control panel.
Do not put a hot pan cover on the
glass surface of the hob.
Do not let cookware boil dry.
Be careful not to let objects or
cookware fall on the appliance. The
surface can be damaged.
Do not activate the cooking zones
with empty cookware or without
cookware.
Do not put aluminium foil on the
appliance.
Cookware made of cast iron,
aluminium or with a damaged bottom
can cause scratches on the glass /
glass ceramic. Always lift these
objects up when you have to move
them on the cooking surface.
This appliance is for cooking
purposes only. It must not be used for
other purposes, for example room
heating.
2.4 Care and cleaning
Clean the appliance regularly to
prevent the deterioration of the
surface material.
Deactivate the appliance and let it
cool down before you clean it.
Disconnect the appliance from the
electrical supply before maintenance.
Do not use water spray and steam to
clean the appliance.
Clean the appliance with a moist soft
cloth. Use only neutral detergents. Do
not use abrasive products, abrasive
cleaning pads, solvents or metal
objects.
2.5 Service
To repair the appliance contact the
Authorised Service Centre.
Use original spare parts only.
2.6 Disposal
WARNING!
Risk of injury or suffocation.
Contact your municipal authority for
information on how to discard the
appliance correctly.
Disconnect the appliance from the
mains supply.
Cut off the mains electrical cable
close to the appliance and dispose of
it.
www.aeg.com
6
3. INSTALLATION
WARNING!
Refer to Safety chapters.
3.1 Before the installation
Before you install the hob, write down
the information below from the rating
plate. The rating plate is on the bottom
of the hob.
Serial number ...........................
3.2 Built-in hobs
Only use the built-in hobs after you
assemble the hob into correct built-in
units and work surfaces that align to the
standards.
3.3 Connection cable
The hob is supplied with the
connection cable.
Replace the damaged mains cable
only with the spare parts cable. Speak
to your local Authorised Service
Center.
WARNING!
All electrical connections
must be made by a qualified
electrician.
CAUTION!
Do not drill or solder the
wire ends. This is strictly
forbidden!
CAUTION!
Do not connect the cable
without cable end sleeve.
Two-phase connection
1. Remove the cable end sleeve from
black and brown wires.
2. Remove an insulation of the brown
and black cable ends.
3. Apply a new wire end sleeve of 1.5
mm² on each cable end. (special tool
required).
Cable cross section
N
L1
N
L
230V~ 400V 2~N
L2
One-phase connection - 230 V~ Two-phase connection - 400 V 2 ~ N
Green - yellow Green - yellow
N Blue and blue Blue and blue N
L Black and brown Black L1
Brown L2
ENGLISH 7
3.4 Assembly
min.
50mm
min.
500mm
min.
12
min.
60
min.
28
If the appliance is installed
above a drawer, the hob
ventilation can warm up the
items stored in the drawer
during the cooking process.
www.youtube.com/electrolux
www.youtube.com/aeg
How to install your AEG
Induction Hob - Worktop installation
www.aeg.com8
4. PRODUCT DESCRIPTION
4.1 Cooking surface layout
1 1
2
1
1
1
Induction cooking zone
2
Control panel
For detailed information on
the sizes of the cooking
zones refer to "Technical
data".
4.2 Control panel layout
7 852 43
9
1
12 1011
6
Use the sensor fields to operate the appliance. The displays, indicators and sounds tell
which functions operate.
Sensor
field
Function Comment
1
ON / OFF To activate and deactivate the hob.
2
Lock / Child Safety Device To lock / unlock the control panel.
3
SenseBoil® To activate and deactivate the function.
The indicators above the symbol show the
progress of the function.
4
Bridge To activate and deactivate the function.
5
- Heat setting display To show the heat setting.
6
- Timer indicators of cooking
zones
To show for which zone you set the time.
ENGLISH 9
Sensor
field
Function Comment
7
- Timer display To show the time in minutes.
8
Hob²Hood To activate and deactivate the manual
mode of the function.
9
- To select the cooking zone.
10
/
- To increase or decrease the time.
11
PowerBoost To activate the function.
12
- Control bar To set a heat setting.
4.3 Heat setting displays
Display Description
The cooking zone is deactivated.
-
The cooking zone operates.
SenseBoil® operates.
Automatic Heat Up operates.
PowerBoost operates.
+ digit
There is a malfunction.
/ /
OptiHeat Control (3 step Residual heat indicator): continue cooking /
keep warm / residual heat.
Lock / Child Safety Device operates.
Incorrect or too small cookware or no cookware on the cooking zone.
Automatic Switch Off operates.
4.4 OptiHeat Control (3 step
Residual heat indicator)
WARNING!
/ / There is a risk of
burns from residual heat.
The indicators show the level of the
residual heat for the cooking zones you
are currently using. The indicators may
also come on for the neighbouring
cooking zones even if you are not using
them.
The induction cooking zones produce
the heat necessary for the cooking
process directly in the bottom of the
cookware. The glass ceramic is heated by
the heat of the cookware.
www.aeg.com10
5. DAILY USE
WARNING!
Refer to Safety chapters.
5.1 Activating and
deactivating
Touch for 1 second to activate or
deactivate the hob.
5.2 Automatic Switch Off
The function deactivates the hob
automatically if:
all cooking zones are deactivated,
you do not set the heat setting after
you activate the hob,
you spill something or put something
on the control panel for more than 10
seconds (a pan, a cloth, etc.). An
acoustic signal sounds and the hob
deactivates. Remove the object or
clean the control panel.
the hob gets too hot (e.g. when a
saucepan boils dry). Let the cooking
zone cool down before you use the
hob again.
you use incorrect cookware. The
symbol comes on and the cooking
zone deactivates automatically after 2
minutes.
you do not deactivate a cooking zone
or change the heat setting. After
some time
comes on and the hob
deactivates.
The relation between the heat setting
and the time after which the hob
deactivates:
Heat setting The hob deacti-
vates after
1 - 3 6 hours
4 - 7 5 hours
8 - 9 4 hours
10 - 14 1.5 hour
5.3 The heat setting
To set or change the heat setting:
Touch the control bar at the correct heat
setting or move your finger along the
control bar until you reach the correct
heat setting.
5.4 SenseBoil®
The function automatically adjusts the
temperature of water so that it does not
boil over once it reaches the boiling
point.
If there is any residual heat
( / / ) on the
cooking zone you want to
use, an acoustic signal is
emitted and the function
does not start.
1. Touch to activate the hob.
2. Touch to activate the function.
A blinking
appears for cooking
zones on which you can presently use
the function.
3. Touch the control bar of any
available cooking zone for which you
want to start the function (between
the heat setting 1-14).
The function starts.
If you do not choose any cooking zone
within 5 seconds the function does not
activate.
Once the function starts the
indicators above the
symbol come on one after
another until the water
reaches the boiling point.
When the function detects the boiling
point the hob emits an acoustic signal
and the heat level automatically changes
to 8.
ENGLISH
11
If all cooking zones are
already in use or there is
some residual heat on all of
them, the hob emits a beep
sound, the indicators above
blink and the function
does not start.
To deactivate the function touch (the
function deactivates and the heat setting
goes down to 0) or touch the control bar
and adjust the heat setting manually.
5.5 Using the cooking zones
Place the cookware in the centre of the
selected zone. Induction cooking zones
adapt to the dimension of the bottom of
the cookware automatically.
You can cook with large cookware
placed on two cooking zones at the
same time. The cookware must cover the
centres of both zones but not go beyond
the area marking. If the cookware is
located between the two centres, Bridge
function will not be activated.
5.6 Bridge
The function operates when
the pot covers the centres of
the two zones. It does not
work with the SenseBoil®
function.
This function connects two left side
cooking zones and they operate as one.
First set the heat setting for one of the
left side cooking zones.
To activate the function: touch
. To
set or change the heat setting touch one
of the control sensors.
To deactivate the function: touch .
The cooking zones operate
independently.
5.7 Automatic Heat Up
Activate this function to get a desired
heat setting in a shorter time. When it is
on, the zone operates on the highest
setting in the beginning and then
continues to cook at the desired heating
setting.
To activate the function the
cooking zone must be cold.
To activate the function for a cooking
zone: touch
( comes on).
Immediately touch a desired heat
setting. After 3 seconds comes on.
To deactivate the function: change the
heat setting.
5.8 PowerBoost
This function makes more power
available to the induction cooking zones.
The function can be activated for the
induction cooking zone only for a limited
period of time. After this time the
induction cooking zone automatically
sets back to the highest heat setting.
Refer to “Technical data”
chapter.
To activate the function for a cooking
zone: touch
. comes on.
To deactivate the function: change the
heat setting.
5.9 Timer
Count Down Timer
You can use this function to set how long
the cooking zone should operate for a
single cooking session.
www.aeg.com
12
First set the heat setting for the cooking
zone then set the function.
To set the cooking zone: touch
again and again until the indicator of a
necessary cooking zone comes on.
To activate the function: touch of
the timer to set the time (00 - 99
minutes). When the indicator of the
cooking zone starts to flash slowly the
time counts down.
To see the remaining time: set the
cooking zone with . The indicator of
the cooking zone starts to flash quickly.
The display shows the remaining time.
To change the time: set the cooking
zone with
. Touch or .
To deactivate the function: set the
cooking zone with and touch . The
remaining time counts back to 00. The
indicator of the cooking zone goes out.
When the time comes to an
end, the sound operates and
00 flashes. The cooking zone
deactivates.
To stop the sound: touch .
CountUp Timer
You can use this function to monitor how
long the cooking zone operates.
To set the cooking zone: touch
again and again until the indicator of a
necessary cooking zone comes on.
To activate the function: touch of
the timer.
comes on. When the
indicator of the cooking zone starts to
flash slowly the time counts up. The
display switches between and
counted time (minutes).
To see how long the cooking zone
operates: set the cooking zone with .
The indicator of the cooking zone starts
to flash quickly. The display shows how
long the zone operates.
To deactivate the function: set the
cooking zone with
and touch or
. The indicator of the cooking zone
goes out.
Minute Minder
You can use this function as a Minute
Minder when the hob is activated and
the cooking zones do not operate. The
heat setting display shows
.
To activate the function: touch .
Touch or of the timer to set the
time. When the time comes to an end,
the sound operates and 00 flashes.
To stop the sound: touch .
The function has no effect
on the operation of the
cooking zones.
5.10 Lock
You can lock the control panel while
cooking zones operate. It prevents an
accidental change of the heat setting.
Set the heat setting first.
To activate the function: touch
.
comes on for 4 seconds. The Timer stays
on.
To deactivate the function: touch .
The previous heat setting comes on.
When you deactivate the
hob, you also deactivate this
function.
5.11 Child Safety Device
This function prevents an accidental
operation of the hob.
To activate the function: activate the
hob with . Do not set any heat setting.
Touch for 4 seconds. comes on.
Deactivate the hob with .
To deactivate the function: activate the
hob with
. Do not set any heat setting.
Touch for 4 seconds. comes on.
Deactivate the hob with .
To override the function for only one
cooking time: activate the hob with
.
ENGLISH
13
comes on. Touch for 4 seconds.
Set the heat setting in 10 seconds. You
can operate the hob. When you
deactivate the hob with the function
operates again.
5.12 OffSound Control
(Deactivating and activating
the sounds)
Deactivate the hob. Touch for 3
seconds. The display comes on and goes
out. Touch
for 3 seconds. or
comes on. Touch of the timer to
choose one of the following:
- the sounds are off
- the sounds are on
To confirm your selection wait until the
hob deactivates automatically.
When the function is set to you can
hear the sounds only when:
you touch
Minute Minder comes down
Count Down Timer comes down
you put something on the control
panel.
5.13 Power limitation
Originally the hob is at its highest
possible power level.
To decrease or increase the power
level:
1. Deactivate the hob.
2. Touch for 3 seconds. The display
comes on and goes off.
3. Touch for 3 seconds. or
comes on.
4. Touch . P 72 comes on.
5. Touch
/ of the Timer to set the
power level.
Power levels
Refer to “Technical data” chapter.
P 72 — 7200 W
P 15 — 1500 W
P 20 — 2000 W
P 25 — 2500 W
P 30 — 3000 W
P 35 — 3500 W
P 40 — 4000 W
P 45 — 4500 W
P 50 — 5000 W
P 60 — 6000 W
CAUTION!
Make sure that the selected
power fits the house
installation fuses.
WARNING!
If you select one of the
lowest power levels the
SenseBoil® function may not
work. Refer to the table
below.
- the function works, - the function
does not work.
Power
levels
Cooking zone
Left
front
Left
rear
Right
front
Right
rear
210
mm
210
mm
145
mm
180
mm
P 72
P 15
P 20
P 25
P 30
P 35
P 40
P 45
P 50
P 60
5.14 Power management
Cooking zones are grouped
according to the location and number
of the phases in the hob. See the
illustration.
www.aeg.com
14
Each phase has a maximum electricity
loading of 3600 W.
The function divides the power
between cooking zones connected to
the same phase.
The function activates when the total
electricity loading of the cooking
zones connected to a single phase
exceeds 3600 W.
The function decreases the power to
the other cooking zones connected to
the same phase.
The heat setting display of the
reduced zones alternates between
the chosen heat setting and the
reduced heat setting. After some time
the heat setting display of the
reduced zones stays on the reduced
heat setting.
Power management with Power
limitation
When you set the Power limitation
function to 6.0 kW or less, power of the
hob is divided between all cooking
zones.
When you set the Power limitation
function to more than 6.0 kW, the
power of the hob is divided between its
left and right side.
5.15 Hob²Hood
It is an advanced automatic function
which connects the hob to a special
hood. Both the hob and the hood have
an infrared signal communicator. Speed
of the fan is defined automatically on
basis of mode setting and temperature
of the hottest cookware on the hob. You
can also operate the fan from the hob
manually.
For most of the hoods the
remote system is originally
deactivated. Activate it
before you use the function.
For more information refer
to hood user manual.
Operating the function automatically
To operate the function automatically set
the automatic mode to H1 – H6. The hob
is originally set to H5. The hood reacts
whenever you operate the hob. The hob
recognizes temperature of the cookware
automatically and adjusts the speed of
the fan.
Automatic modes
Auto-
matic
light
Boiling
1)
Frying
2)
Mode H0 Off Off Off
Mode H1 On Off Off
Mode
H2
3)
On Fan
speed 1
Fan
speed 1
Mode H3 On Off Fan
speed 1
Mode H4 On Fan
speed 1
Fan
speed 1
Mode H5 On Fan
speed 1
Fan
speed 2
ENGLISH 15
Auto-
matic
light
Boiling
1)
Frying
2)
Mode H6 On Fan
speed 2
Fan
speed 3
1)
The hob detects the boiling process and acti-
vates fan speed in accordance with automatic
mode.
2)
The hob detects the frying process and acti-
vates fan speed in accordance with automatic
mode.
3)
This mode activates the fan and the light and
does not rely on the temperature.
Changing the automatic mode
1. Deactivate the appliance.
2. Touch for 3 seconds. The display
comes on and goes off.
3. Touch
for 3 seconds.
4. Touch a few times until comes
on.
5. Touch
of the Timer to select an
automatic mode.
To operate the hood directly
on the hood panel
deactivate the automatic
mode of the function.
When you finish cooking and
deactivate the hob, the
hood fan may still operate
for a certain period of time.
After that time the system
deactivates the fan
automatically and prevents
you from accidental
activation of the fan for the
next 30 seconds.
Operating the fan speed manually
You can also operate the function
manually. To do that touch when the
hob is active. This deactivates automatic
operation of the function and allows you
to change the fan speed manually. When
you press you raise the fan speed by
one. When you reach an intensive level
and press again you will set fan speed
to 0 which deactivates the hood fan. To
start the fan again with fan speed 1 touch
.
To activate automatic
operation of the function,
deactivate the hob and
activate it again.
Activating the light
You can set the hob to activate the light
automatically whenever you activate the
hob. To do so set the automatic mode to
H1 – H6.
The light on the hood
deactivates 2 minutes after
deactivating the hob.
6. HINTS AND TIPS
WARNING!
Refer to Safety chapters.
6.1 Cookware
For induction cooking zones
a strong electro-magnetic
field creates the heat in the
cookware very quickly.
www.aeg.com16
Use the induction cooking
zones with suitable
cookware.
Cookware material
correct: cast iron, steel, enamelled
steel, stainless steel, multi-layer
bottom (with a correct marking from a
manufacturer).
not correct: aluminium, copper,
brass, glass, ceramic, porcelain.
Cookware is suitable for an induction
hob if:
water boils very quickly on a zone set
to the highest heat setting.
a magnet pulls on to the bottom of
the cookware.
The bottom of the cookware
must be as thick and flat as
possible.
Ensure pan bases are clean
and dry before placing on
the hob surface.
Cookware dimensions
Induction cooking zones adapt to the
dimension of the bottom of the
cookware automatically.
The cooking zone efficiency is related to
the diameter of the cookware. The
cookware with a diameter smaller than
the minimum receives only a part of the
power generated by the cooking zone.
Refer to "Technical data".
6.2 The noises during
operation
If you can hear:
crack noise: cookware is made of
different materials (a sandwich
construction).
whistle sound: you use a cooking
zone with a high power level and the
cookware is made of different
materials (a sandwich construction).
humming: you use a high power level.
clicking: electric switching occurs.
hissing, buzzing: the fan operates.
The noises are normal and do not
indicate any malfunction.
6.3
Hints & Tips for
SenseBoil®
The function works best for boiling water
and preparing potatoes.
It does not work with cast
iron and non-stick cookware,
e.g. with a ceramic coating.
Enamelled steel pots are
recommended for achieving
the best results while boiling
potatoes.
Check if the pot you chose is suitable for
SenseBoil® by monitoring the first
cooking session.
To use SenseBoil® efficiently follow the
advice below:
Fill between half to three quarters of
the pot with cold tap water leaving 4
cm from the rim of the pot empty. Do
not use less than 1 or more than 5
litres of water. Make sure the total
weight of the water (or the water and
potatoes) ranges between 1-5 kg.
If you want to cook potatoes, make
sure they are completely covered with
water, but remember to leave at least
one quarter of the pot empty.
To achieve the best results cook only
whole, unpeeled, medium-sized
potatoes.
Make sure you do not pack potatoes
too tightly.
Avoid producing external vibrations
(e.g. from using a blender or placing a
mobile phone next to the appliance)
when the function is running.
If you want to use salt, add it after the
water reaches the boiling point.
The function may not work properly
for water kettles and espresso pots.
6.4 Öko Timer (Eco Timer)
To save energy, the heater of the
cooking zone deactivates before the
count down timer sounds. The difference
in the operation time depends on the
heat setting level and the length of the
cooking operation.
ENGLISH
17
6.5 Examples of cooking
applications
The correlation between the heat setting
of a zone and its consumption of power
is not linear. When you increase the heat
setting, it is not proportional to the
increase of the consumption of power. It
means that a cooking zone with the
medium heat setting uses less than a half
of its power.
The data in the table is for
guidance only.
Heat setting Use to: Time
(min)
Hints
1 Keep cooked food warm. as nec-
essary
Put a lid on the cookware.
1 - 3 Hollandaise sauce, melt: but-
ter, chocolate, gelatine.
5 - 25 Mix from time to time.
1 - 3 Solidify: fluffy omelettes,
baked eggs.
10 - 40 Cook with a lid on.
3 - 5 Simmer rice and milkbased
dishes, heat up ready-cooked
meals.
25 - 50 Add at least twice as much liq-
uid as rice, mix milk dishes
halfway through the proce-
dure.
5 - 7 Steam vegetables, fish, meat. 20 - 45 Add a couple of tablespoons
of liquid.
7 - 9 Steam potatoes. 20 - 60 Use max. ¼ l of water for 750 g
of potatoes.
7 - 9 Cook larger quantities of food,
stews and soups.
60 - 150 Up to 3 l of liquid plus ingredi-
ents.
9 - 12 Gentle fry: escalope, veal cor-
don bleu, cutlets, rissoles,
sausages, liver, roux, eggs,
pancakes, doughnuts.
as nec-
essary
Turn halfway through.
12 - 13 Heavy fry, hash browns, loin
steaks, steaks.
5 - 15 Turn halfway through.
14 Boil water, cook pasta, sear meat (goulash, pot roast), deep-fry chips.
Boil large quantities of water. PowerBoost is activated.
6.6 Hints and Tips for
Hob²Hood
When you operate the hob with the
function:
Protect the hood panel from direct
sunlight.
Do not spot halogen light on the
hood panel.
Do not cover the hob control panel.
Do not interrupt the signal between
the hob and the hood (e.g. with the
hand, a cookware handle or a tall
pot). See the picture.
The hood in the picture is only
exemplary.
www.aeg.com18
Other remotely controlled
appliances may block the
signal. Do not use any such
appliances near to the hob
while Hob²Hood is on.
Cooker hoods with the Hob²Hood
function
To find the full range of cooker hoods
which work with this function refer to our
consumer website. The AEG cooker
hoods that work with this function must
have the symbol
.
7. CARE AND CLEANING
WARNING!
Refer to Safety chapters.
7.1 General information
Clean the hob after each use.
Always use cookware with a clean
base.
Scratches or dark stains on the surface
have no effect on how the hob
operates.
Use a special cleaner suitable for the
surface of the hob.
Use a special scraper for the glass.
7.2 Cleaning the hob
Remove immediately: melted plastic,
plastic foil, sugar and food with sugar,
otherwise, the dirt can cause damage
to the hob. Take care to avoid burns.
Use a special hob scraper on the glass
surface at an acute angle and move
the blade on the surface.
Remove when the hob is sufficiently
cool: limescale rings, water rings, fat
stains, shiny metallic discoloration.
Clean the hob with a moist cloth and
a non-abrasive detergent. After
cleaning, wipe the hob dry with a soft
cloth.
Remove shiny metallic
discoloration: use a solution of water
with vinegar and clean the glass
surface with a cloth.
8. TROUBLESHOOTING
WARNING!
Refer to Safety chapters.
8.1 What to do if...
Problem Possible cause Remedy
You cannot activate or oper-
ate the hob.
The hob is not connected to
an electrical supply or it is
connected incorrectly.
Check if the hob is correctly
connected to the electrical
supply. Refer to the connec-
tion diagram.
ENGLISH 19
Problem Possible cause Remedy
The fuse is blown. Make sure that the fuse is
the cause of the malfunction.
If the fuse is blown again
and again, contact a quali-
fied electrician.
You do not set the heat set-
ting for 10 seconds.
Activate the hob again and
set the heat setting in less
than 10 seconds.
You touched 2 or more sen-
sor fields at the same time.
Touch only one sensor field.
There is water or fat stains
on the control panel.
Clean the control panel.
An acoustic signal sounds
and the hob deactivates.
An acoustic signal sounds
when the hob is deactivated.
You put something on one
or more sensor fields.
Remove the object from the
sensor fields.
The hob deactivates. You put something on the
sensor field .
Remove the object from the
sensor field.
Residual heat indicator does
not come on.
The zone is not hot because
it operated only for a short
time or the sensor is dam-
aged.
If the zone operated suffi-
ciently long to be hot, speak
to an Authorised Service
Centre.
Hob²Hood does not work. You covered the control
panel.
Remove the object from the
control panel.
You use a very tall pot which
blocks the signal.
Use a smaller pot, change
the cooking zone or operate
the hood manually.
Automatic Heat Up does not
operate.
The zone is hot. Let the zone become suffi-
ciently cool.
The highest heat setting is
set.
The highest heat setting has
the same power as the func-
tion.
The heat setting changes
between two levels.
Power management oper-
ates.
Refer to "Daily use".
The sensor fields become
hot.
The cookware is too large or
you put it too near to the
controls.
Put large cookware on the
rear zones, if possible.
There is no sound when you
touch the panel sensor
fields.
The sounds are deactivated. Activate the sounds. Refer to
"Daily use".
www.aeg.com20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76

AEG IAE64423FB Manuel utilisateur

Catégorie
Plaques de cuisson
Taper
Manuel utilisateur

dans d''autres langues