testo Instruments (Shenzhen) 2ACVD-1510 Manuel utilisateur

Marque: testo Instruments (Shenzhen)

Modèle: 2ACVD-1510

Taper: Manuel utilisateur

testo • Smart Probes

Startup instruction

All Smart Probes only work in combination with a mobile terminal

and the testo Smart Probes App.

2 Overview

2

1 Safety

1.1. Safety with testo 510i

WARNING

Magnetic field

May be harmful to those with pacemakers.

> Keep a minimum distance of 10 cm between pacemaker and

instrument.

1.2. Safety with testo 549i

WARNING

Risk of injury caused by pressurized, hot, cold or toxic refrigerants/media!

> Only to be used by qualified staff.

> Wear protective goggles and safety gloves.

> Before applying pressure to the measuring instrument: always fix the

instrument tightly onto the pressure connection.

> Comply with the permissible measuring range (0 to 60 bar). Pay

particular attention to this in systems with R744 refrigerant, since these

are frequently operated with higher pressures!

1.3. Safety with testo 805i

CAUTION

Laser radiation! Class 2 laser

> Do not look into the laser beam!

2 Overview

1 Measuring unit

2 LED

3 Key

4 Battery compartment (at the back)

4 Bluetooth® module

3

3 Switching on/off

3.1. Switching on

Testo 549i

1. Pull the film out of the battery compartment.

2. Press the key.

- The Smart Probes switch on.

3.2. Switching off

1. Press and hold the key.

- The Smart Probes switch off.

4 Bluetooth® module

4.1. Establishing Bluetooth® connection

You need a Tablet or Smartphone with the Testo Smart Probes

App already installed on it to be able to establish a Bluetooth

connection.

You can get the App for iOS instruments in the App Store or for

Android instruments in the Play Store.

Compatibility:

• requires iOS 8.3 or later / Android 4.3 or later

• requires Bluetooth 4.0

4.2. Bluetooth® approval

The Bluetooth® option may only be operated in countries in which

it is type approved. For further information, please refer to the

instruction manual at: www.testo.de/SmartProbesManuals.html.

FCC (Federal Communications Commission) countries information

This instrument complies with part 15 of the FCC Rules. Its

commissioning is subject to the following two conditions: (1) This

instrument must not cause any harmful interference and (2) this

instrument must be able to accept interference, even if this could

have undesired effects on operation.

Changes

The FCC demands that the user be informed that any changes or

modifications to the instrument that have not been explicitly

approved by Testo AG may void the user's right to use this

instrument.

To find out how to handle the product safely and for detailed

information, please refer to the instruction manual at:

www.testo.de/SmartProbesManuals.html.

6 Transmitting reading

4

5 LED status

LED status Meaning

Flashing red Low battery status

Flashing yellow • Smart Probe is switched on.

• Smart Probe searching, but not yet connected.

Flashing green • Smart Probe is switched on.

• Bluetooth is connected.

6 Transmitting reading

✓ The Smart Probes are switched on and connected to their mobile

terminal via Bluetooth.

1. The Smart Probes' readings are automatically shown in the standard

display.

2. Press the key.

- The reading that is currently present is held.

3. Press the key again.

- The instrument again displays the current readings.

These commissioning instructions describe the basic operating

steps.

To find out how to handle the product safely and for detailed

information, please refer to the instruction manual at:

www.testo.de/SmartProbesManals.html.

This equipment complies with FCC RF radiation exposure limits set forth

for an uncontrolled environment.

RF Exposure:

Canada IC Statement:

Le présent appareil est conforme aux CNR d'Industrie Canada

applicables aux appareils radio exempts de licence.

L'exploitation est autorisée aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage est susceptible

d'en compromettre le fonctionnement.

This device complies with RSS-247 of Industry Canada

1
2
3
4

testo Instruments (Shenzhen) 2ACVD-1510 Manuel utilisateur

Marque: testo Instruments (Shenzhen)

Modèle: 2ACVD-1510

Taper: Manuel utilisateur

Télécharger le PDF

dans d''autres langues

English: testo Instruments (Shenzhen) 2ACVD-1510 User manual

Autres documents