Yale YRCB-490-CB1-WSP Manuel utilisateur

YRCB-490-CB1-WSP
Yale
Marque
Yale
Modèle
YRCB-490-CB1-WSP
Taper
Manuel utilisateur

Ce manuel convient également à

Smart Cabinet Lock
Installation Instructions
Glow in the Dark
Emergency Release
If you have any questions while installing, call our 24/7 tech
support team! Call 1-855-213-5841 or email Support@YaleLock.com
Failure to follow these instructions could result in damage to the product and void the factory warranty
YRCB490-MNL-0014 Rev B
Trusted every day Part of ASSA ABLOY
x1
Lockbody
x2
M4x12 Screw
x2
Standard Lock
Post
x1
CR2 Battery
x1
Lock Post
Guide
x1
Mounting Template
x5
3M Mounting Tape
x4
M3x10 Screw
1 4
x1
Double Door
Plate
x1
Mounting Bracket
x1
Long Lock Post
YRCB490-MNL-0014 Rev B
Trusted every day Part of ASSA ABLOY
YRCB490-MNL-0014 Rev B
Trusted every day Part of ASSA ABLOY
2
Download the Yale Access App
1
Insert CR2 Battery Into Lockbody
2
Lock will automatically unlock if
batteries die. Your app will alert
you when batteries are low.
IOS 11.0 + Android 6.0 +
YRCB490-MNL-0014 Rev B
Trusted every day Part of ASSA ABLOY
3
Attach 3M Tape to Mounting
Bracket and Lock Post
3
Slide Mounting Bracket onto
Bottom of Lockbody
4
Clean surface before application
and allow up to 24 hours for
proper bondage.
If cabinet has a face frame or
lip (max 1” high x max 1-1/4”
deep), use long lock post.
YRCB490-MNL-0014 Rev B
Trusted every day Part of ASSA ABLOY
4
Slide Lock Post Guide onto
Lock Post
5
Attach Lock Post to Lockbody
6
YRCB490-MNL-0014 Rev B
Trusted every day Part of ASSA ABLOY
Place mounting template in
desired location for installation.
Remove 3M film
from mounting bracket.
Install Smart Cabinet Lock
7
Mounting template cannot be
used to position lock when
using long lock post.
5
YRCB490-MNL-0014 Rev B
Trusted every day Part of ASSA ABLOY
Attach Lock Post to Door
8
6
YRCB490-MNL-0014 Rev B
Trusted every day Part of ASSA ABLOY
7
Remove Lock Post Guide
9
Test Operation
YRCB490-MNL-0014 Rev B
Trusted every day Part of ASSA ABLOY
8
Congratulations! You've installed the Yale® Smart Cabinet Lock.
Follow the steps in your Yale Access app to complete the setup process.
NOTE TO INSTALLER AND CONSUMER
A second lock post is provided as a spare in the
event the cabinet door must be forced open and
installed lock post is broken.
YRCB490-MNL-0014 Rev B
Trusted every day Part of ASSA ABLOY
9
x2
x2
Screw Mounting
Remove lockbody from
mounting bracket to
access screw holes.
Make sure screws are
no longer than depth of
your cabinet door.
O
optional
Top Of Cabinet Installation
O
optional
YRCB490-MNL-0014 Rev B
Trusted every day Part of ASSA ABLOY
10
Double Door Plate
O
optional
x2
or
Use screws OR double sided tape to
adhere the double door plate when
installing the Smart Cabinet Lock on the
adjacent door of a double door cabinet.
YRCB490-MNL-0014 Rev B
Trusted every day Part of ASSA ABLOY
11
Long Lock Post
O
optional
The Long Lock Post is used on cabinets
with a face frame or lip no taller than
1” and no deeper than 1-1/4”.
Mounting template
cannot be used to
position lock when
using long lock post.
YRCB490-MNL-0014 Rev B
Trusted every day Part of ASSA ABLOY
Warning: Changes or modifications to this device, not expressly approved by
Yale Home could void the user's authority to operate the equipment.
Yale® is a registered trademark of Yale Home. Other products' brand names may be trademarks or
registered trademarks of their respective owners and are mentioned for reference purposes only.
© Copyright 2020. All rights reserved. Reproduction in whole or in part without the express written
permission of Yale Home is prohibited.
24/7 Product Support : 1-855-213-5841 • www.US.YaleHome.com
Yale Home
FCC:
Contain FCC ID: 2ABFGYRIZW2USTS1
Model: YRCB490BLEWSP
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS.
(1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
Industry Canada:
Contain 11626AYRIZW2USTS1
Model: YRCB490BLEWSP
Section 7.1.2 of RSSGEN Under Industry Canada regulations,
this radio transmitter may only operate using an antenna of a
type and maximum (or lesser) gain approved for the
transmitter by Industry Canada. To reduce potential radio
interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated
power (e.i.r.p.) is not more than that necessary for successful
communication.
En vertu des règlements d’Industrie Canada, cet émetteur
radio ne peut fonctionner avec une antenne d’un type et un
maximum (ou moins) approuves pour gagner de l’émetteur par
Industrie Canada. Pour réduire le risque d’interférence aux
autres utilisateurs, le type d’antenne et son gain doivent être
choisies de façon que la puissance isotrope rayonnée
équivalente (PIRE) ne dépasse pas ce qui est nécessaire pour
une communication réussie.
Section 7.1.3 or RSSGEN This Device complies with Industry
Canada License-exempt RSS standard(s). Operation is subject
to the following two conditions: 1) this device may not cause
interference, and 2) this device must accept any interference,
including interference that may cause undesired operation of
the device.
Cet appareil est conforme avec Industrie Canada RSS standard
exemptes de licence(s). Son fonctionnement est soumis aux
deux conditions suivantes: 1) ce dispositif ne peut causer des
interférences, et 2) cet appareil doit accepter toute
interférence, y compris les interférences qui peuvent causer un
mauvais fonctionnement du dispositif.
This radio transmitter 6982AYRHCPZW0FM has been
approved by Industry Canada to operate with the antenna
types listed below with the maximum permissible gain
indicated. Antenna types not included in this list, having a gain
greater than the maximum gain indicated for that type, are
strictly prohibited for use with this device.
Le présent émetteur radio 6982AYRHCPXW0FM a été
approuve par Industrie Canada pour fonctionner avec les types
d’antenne énumérés ci-dessous et ayant un gain admissible
maximal. Les types d’antenne non inclus dans cette liste, et
dont le gain est supérieur au gain maximal indique, sont
strictement interdits pour l’exploitation de l’émetteur.
CAN ICES3B/NMB3B
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Yale YRCB-490-CB1-WSP Manuel utilisateur

YRCB-490-CB1-WSP
Yale
Marque
Yale
Modèle
YRCB-490-CB1-WSP
Taper
Manuel utilisateur
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents