Yale Smart Safe Manuel utilisateur

Marque: Yale

Modèle: Smart Safe

Taper: Manuel utilisateur

Ce manuel convient également à

IESD100PG0

Yale Smart Safe

Installation Instructions

If you have any questions while installing, call our 24/7 tech support team! Call 1-855-213-5841 or email Support@YaleLock.com

Tip: If you already use the

August App, use the same

username and password.

YRSF-MD-MNL-0020 Rev B Part of ASSA ABLOY

1Download the Yale Access App

Create an account

Open the battery

compartment and

insert 4 AA batteries.

Reinstall the cover.

2Unlock Safe Using Key

Open door and leave open

until setup is complete.

Tip: When key is used to

unlock, it must be used to

lock.

Insert Batteries

Set up Smart Safe

Tap "Set up a device" from the app menu. When asked,

scan the Yale QR code on the inside of your safe door.

Tip: Once batteries are inserted, you have 10 minutes

to complete this step. If your app doesn't find the safe,

press and hold (5 secs) the reset button on the inside

of the safe door.

Set up Connect*

Note serial number located on back of Connect. Plug Connect

into an INDOOR outlet within 10 feet of the Smart Safe.

Tip: For best connectivity, make sure that the Connect bridge

is in the line of sight of the front of the safe.

Add Safe to the Yale Access App

*Connect WiFi Bridge included with select models

OMount Safe For Added Security (Optional)

There are 8 mounting hole locations on the Smart

Safe. Use included mounting template for guidance

to secure the safe to the wall, shelf or floor.

Tips:

• Use Phillips #2 screwdriver to tighten screws.

• To avoid scratching or damaging your floor, attach

the included 4 rubber feet to the bottom of the safe

with the 3M side against safe.

optional

Pour la version francaise voir US.YaleHome.com/Support

Key

Mounting

Hardware

Needed for Optional Installation

Drill with

3/8" Drill Bit Pencil

AA Batteries

(Alkaline only)

Connect WiFi Bridge

(Included with Select Models)

Phillips #2

Screwdriver

Rubber Feet

Once added to the Yale Access App,

you can create and delete

entry codes or share app access by

tapping the Guest icon in the

bottom menu.

Create Entry Codes

Using Your Smart Safe

9 Volt Battery Back-up

(Use Alkaline battery)

Hold battery to quickly recharge.

Keyhole

Cover

Outside

LED Keyhole

Enter/Unlock

(Set/Continue)

Safe

Wake Up /

Settings

Settings Definitions

YRSF-MD-MNL-0020 Rev B Part of ASSA ABLOY

Warning: Changes or modiﬁcations to this device not expressly approved by

Yale Home could void the user's authority to operate the equipment.

Yale® is a registered trademark of Yale Home. Use of the Works with Apple badge means that an accessory has been designed to work specifically with the technology identified in the badge and has been

certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Other products' brand names

express written permission of Yale Home is prohibited.

24/7 Support 1-855-213-5841 • US.YaleHome.com

Yale Home

FCC ID: 2ABFG-IESD100PG0

FCC

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received,

including interference that may cause undesired operation.

Any changes or modifications (including the antennas) to

this device that are not expressly approved by the

manufacturer may void the user's authority to operate the

equipment.

Note : This equipment has been tested and found to

comply with the limits for a Class B digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference

in a residential installation This equipment generates, uses

and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause

harmful interference to radio communications, However,

there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception, which

can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by

one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and

receiver.

- Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician

for help.

Modifications not expressly approved by the manufacturer

could void your authority to operate the equipment under

FCC rules.

IC ID: 11626A-IESD100PG0

ISED

This device contains licence-exempt

transmitter(s)/receiver(s) that comply with Innovation,

Science and Economic Development Canada’s

licence-exempt RSS(s). Operation is subject to the following

two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including

interference that may cause undesired operation of the

device.

L’émetteur/récepteur exempt de licence contenu dans le

présent appareil est conforme aux CNR d’Innovation,

Sciences et Développement économique Canada

applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes :

(1) L’appareil ne doit pas produire de brouillage;

(2) L’appareil doit accepter tout brouillage radioélectrique

subi, même si le brouillage est susceptible d’en

compromettre le fonctionnement.

FCC and IC RF Radiation Exposure Statement:

This equipment complies with FCC and IC RF Radiation

exposure limits set forth for an uncontrolled environment.

This device and its antenna must not be co-located or

operating in conjunction with any other antenna or

transmitter.

RF du FCC et IC d'exposition aux radiations:

Cet équipement est conforme à l'exposition de FCC et IC

rayonnements RF limites é-tablies pour un environnement

non contrôlé.

L’antenne pour ce transmetteur ne doit pas être même

endroit avec d’autres émetteur sauf conformément à FCC et

IC procédures de produits Multi-émetteur.

While in Privacy Mode, the

safe will not open even

when a valid Entry Code is

entered. This setting can

be changed from the Yale

Access App.

The inside light will

automatically turn on and

stay on for 10 seconds

when the safe door is

opened.

Setting Default Definition

Privacy

Mode

Inside Light

One Touch

Locking

Sound On

This setting cannot

be turned off.

This feature cannot

be turned off.

Off

The sound setting for entry

code verification can be set

from the Yale Access App.

Inside

LED

Battery

Compartment

Key

Hooks

Reset Button*

(Factory Settings)

* When safe is paired to app, Factory Reset must be done

from app. During a factory reset the safe will be unlocked.

Low Battery Warning

Safe can always be opened with the key

or with a 9V battery and valid code.

Touching any key on

keypad will lock the safe.

Locking Safe

Close Safe Door

Press any key to lock safe

Unlocking Safe

Enter valid 4-6 digit code

Press

Yale Smart Safe Manuel utilisateur

Marque: Yale

Modèle: Smart Safe

Taper: Manuel utilisateur

Ce manuel convient également à

IESD100PG0

Télécharger le PDF

rapport

dans d''autres langues

English: Yale Smart Safe User manual

Yale Smart Safe Manuel utilisateur

Ce manuel convient également à

Yale Smart Safe Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents