Assa Abloy IN120 Manuel utilisateur

Marque: Assa Abloy

Modèle: IN120

Taper: Manuel utilisateur

02/28/23

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

IN120 / IN220 10X Line Bored Lock

A8356A • www.sargentlock.com • 1-800-810-WIRE 3

Changes or modifications to this device not expressly approved by ASSA ABLOY could void

the user’s authority to operate the equipment.

Warning

To avoid possible damage from electrostatic discharge (ESD), some basic precautions should be used when handling electronic components:

• Minimize build-up of static by touching and/or maintaining contact with unpainted metal surfaces such as door hinges, latches, and

mounting plates especially when mounting electronic components such as readers and controllers onto the door.

• Leave components (reader and controller) protected in their respective anti-static bags until ready for installation

• Do not touch pins, leads or solder connections on the circuit boards

This product can expose you to lead which is known to the state of California to cause cancer and birth defects or other reproductive harm.

For more information go to: www.P65warnings.ca.gov.

Ce produit peut vous exposer au plomb qui, dans l’état de la Californie, est reconnu pour causer le cancer, des anomalies congénitales ou d’autres problèmes

de reproduction.

Pour plus d’informations, visitez: www.P65warnings.ca.gov.

Any retrofit or other field modification to a fire rated opening can potentially impact the fire rating of the opening, and SARGENT Manufacturing makes no

representations or warranties concerning what such impact may be in any specific situation. When retrofitting any portion of an existing fire rated opening,

or specifying and installing a new fire-rated opening, please consult with a code specialist or local code official (Authority Having Jurisdiction) to ensure

compliance with all applicable codes and ratings.

General Regulatory Compliance:

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt

RSS(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation of the device.

Ce dispositif contient des émetteurs/réceptuers exemptés de licence conformes aux RSS d’Innovation, Sciences et Développment économique Canada.

L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence, et (2) ce dispositif doit accepter n’importe quelle

interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée a le dispositif.

This equipment complies with FCC and IC radiation exposure limits set forth for general population (uncontrolled environment). This device must not be

co-located or operating in conjunction with any other antenna or transmitter.

Cet équipement est conforme aux limites d’exposition aux radiations de la FCC et IC définies pour la population générale (environnement non contrôlé). Cet

appareil ne doit pas être co-localisé ou fonctionner en conjonction avec une autre antenne ou un autre émetteur.

Innovation, Science and Economic Development Canada:

Under Innovation, Science and Economic Development Canada regulations, this radio transmitter may only operate using an antenna of a type and

maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its

gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

Conformément à la réglementation d’Innovation, Sciences et Développement économique Canada, le présent émetteur radio peut fonctionner avec une

antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage

radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente

(p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.

FCC:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.