Waring Commercial WMO90 Manuel utilisateur

.9 CU. FT. MEDIUM-DUTY

MICROWAVE OVEN

HORNO DE MICROONDAS DE 25 L

DE SERVICIO MEDIO

FOUR À MICRO-ONDES DE 25 L

À USAGE MODÉRÉ

WMO90

For your safety and continued enjoyment of this product,

always read the instruction book carefully before using.

Para su seguridad y para disfrutar plenamente de este producto,

siempre lea cuidadosamente las instrucciones antes de usarlo.

An que votre appareil vous procure en toute sécurité beaucoup

de satisfaction, lire attentivement le mode d’emploi avant de l’utiliser.

2

IMPORTANT SAFETY

INSTRUCTIONS

1.

READ ALL INSTRUCTIONS BEFORE USING.

2. Read and specically follow: PRECAUTIONS TO AVOID

POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE

ENERGY found on page 7.

3. As with most cooking appliances, close supervision is

necessary to reduce the risk of re in the oven cavity.

WARNING: To reduce the risk of re in the oven cavity:

i) Do not overcook food. Carefully attend to the appliance when

paper, plastic, or other combustible materials are placed

inside the oven to facilitate cooking.

ii) R emove wire twist ties and metal handles from paper or

plastic containers/bags before placing them in the oven.

iii) If materials inside the oven ignite, keep the oven door

closed. Turn the oven off, and unplug the appliance.

iv) Do not use the oven cavity for storage purposes. Do not

leave paper products, cooking utensils, or food in the cavity

when not in use.

4. This oven must be grounded. Connect only to a properly

grounded outlet. See GROUNDING INSTRUCTIONS found

on page 5.

5. Install or locate this oven only in accordance with the installation

instructions provided on page 11.

6. Some products, such as whole eggs and sealed containers

(for example, closed glass jars), could explode and should

not be heated in the oven.

WARNING: To reduce the risk of burns, electric shock, re, injury

to persons or exposure to excessive microwave oven energy when

using your appliance, follow basic safety precautions, including

the following:

7. Use this appliance only for its intended use as described in

this manual. Do not use corrosive chemicals or vapors in this

appliance. This oven is specically designed to heat, cook or

dry food. It is not designed for industrial or laboratory use.

8. Do not operate this oven if it has a damaged cord or plug, if

it is not working properly, or if it has been damaged or dropped.

3

9. This appliance should be serviced only by qualied service

technicians. Contact the nearest authorized service facility for

examination, repair or adjustment.

10. Do not cover or block any openings on the oven.

11. Do not store or use this appliance outdoors.

12. Do not use this oven near water; for example, near a kitchen

sink, in a wet basement, near a swimming pool, or similar

locations.

13. Do not immerse cord or plug in water.

14. Keep cord away from heated surfaces.

15. D o not let cord hang over edge of table or counter.

16. When cleaning surfaces of door and oven that come into

contact when closing the door, use only mild, nonabrasive

soaps or detergents applied with a sponge or soft cloth.

WARNING: Liquids such as water, coffee or tea may be overheated

beyond the boiling point without appearing to be boiling. Visible

bubbling or boiling is not always present when the container is

removed from the microwave oven. THIS COULD RESULT IN VERY

HOT LIQUIDS SUDDENLY BOILING OVER WHEN THE CONTAINER

IS DISTURBED, OR WHEN A SPOON OR OTHER UTENSIL IS

INSERTED INTO THE LIQUID.

i) Do not overheat the liquid.

ii) Stir the liquid both before and halfway through heating it.

iii) Do not use straight-sided containers with narrow necks.

iv) After heating, allow the container to stand in the microwave

oven for a short time before removing it.

v) Use extreme care when inserting a spoon or other utensil

into the heated container.

17. DO NOT heat baby bottles in microwave oven.

WARNING: DO NOT run this unit without food.

SAVE THESE INSTRUCTIONS

APPROVED FOR COMMERCIAL USE

4

GROUNDING INSTRUCTIONS

DANGER – Electric Shock Hazard

Touching some of the internal components can cause serious

personal injury or death. Do not disassemble this appliance.

Improper use of the grounding can result in electric shock. Do not

plug into an outlet until appliance is properly installed and grounded.

This appliance must be grounded while in use to protect the operator

from electric shock. Appliance is equipped with a 3-foot-long

conductor cord and a 3-prong grounding plug to t into the proper

outlet. In the event of an electrical short circuit, grounding reduces

the risk of electric shock by providing an escape wire for the electric

current. This appliance has a cord with a grounding wire and a

grounding plug, which must be plugged into a properly installed and

grounded outlet.

The WMO90 plug (Fig. 1) can be connected to an adapter (Fig. 2) for

use in 2-prong receptacles. The grounding lug, which extends from

the adapter, must be connected to a permanent ground, such as a

properly grounded outlet box (Fig. 3) using a metal screw.

Consult a qualied electrician or serviceman if the grounding

instructions are not completely understood or if there is doubt as to

whether the appliance is properly grounded.

EXTENSION CORDS & LONG CORD SETS

Use only 3-wire extension cords that have 3-prong grounding type

plugs and 3-pole cord connectors that accept the plug from the

appliance. Use only extension cords that are intended for indoor use.

Use only extension cords having an electrical rating not less than

the rating of the appliance. Do not use damaged extension cords.

Examine extension cord before using and replace if damaged. Do not

abuse extension cord and do not yank on any cord to disconnect.

Keep cord away from heat and sharp edges.

5

NOTE: The WMO90 is for 120V only. This appliance should not be

used with a converter.

PRECAUTIONS TO AVOID POSSIBLE EXPOSURE

TO EXCESSIVE MICROWAVE ENERGY

(a) DO NOT attempt to operate this oven with the door open since

this can result in harmful exposure to microwave energy. It is

important not to defeat or tamper with the safety interlocks.

(b) D O NOT place any object between the oven front face and the

door, or allow soil or cleaner residue to accumulate on sealing

surfaces.

(c) D O NOT operate the oven if it is damaged. It is particularly

important that the oven door closes properly and that there is

no damage to the:

(1) DOOR (bent)

(2) HINGES AND LATCHES (broken or loosened)

(3) DOOR SEALS AND SEALING SURFACE

(d) The oven should not be adjusted or repaired by anyone except

properly qualied service personnel.

RADIO INTERFERENCE

1. Operation of the microwave oven may cause interference to

your radio, TV or similar equipment.

2. When there is interference, it may be reduced or eliminated by

taking the following measures:

a) Clean door and sealing surface of the oven.

b) Reorient the receiving antenna of the radio or television.

c) Relocate the microwave oven with respect to the receiver.

d) Move the microwave oven away from the receiver.

e) Plug the microwave oven into a different outlet so that

microwave oven and receiver are on different branch circuits.

CAUTION

Personal Injury Hazard

Tightly closed containers could explode during microwaving. Closed

containers should be opened and plastic pouches should be pierced

before cooking.

6

SAFE MATERIALS FOR MICROWAVE

There may be certain non-metallic utensils and containers that are

not safe to use for microwaving. Refer to the instructions on Materials

You Can Use In Microwave Oven and Materials To Be Avoided In

Microwave Oven on pages 8 and page 9.

To check if a material is microwave safe, you can test it following the

procedure below.

1. Fill a microwave-safe container with 1 cup (250ml) of cold water

along with the utensil in question.

2. Cook on maximum power for 1 minute.

3. Carefully feel the utensil. If the utensil is warm, do not use it for

microwave cooking.

4. Do not exceed 1 minute of cooking time.

MATERIALS YOU CAN USE IN MICROWAVE OVEN

Material Remarks

Dinnerware Microwave-safe only. Follow manufacturer’s

instructions. Do not use cracked or chipped

dishes.

Glass jars Always remove lid. Use only to heat food until just

warm. Most glass jars are not heat resistant and

may break.

Glassware Heat-resistant oven glassware only. Make sure

there is no metallic trim. Do not use cracked or

chipped glassware.

Oven cooking Follow manufacturer’s instructions. Do not close

bags with metal tie. Make slits to allow steam to escape.

Paper plates Use for short–term cooking/warming only. Do not

and cups leave oven unattended while cooking.

Paper towels Use to cover food for reheating and absorbing fat.

Use with supervision for short-term cooking only.

Parchment Use as a cover to prevent splattering or a wrap

paper for steaming.

7

MATERIALS YOU CAN USE IN MICROWAVE OVEN

(CONT)

Plastic Microwave-safe only. Follow the manufacturer’s

instructions. Should be labeled as microwave safe.

Some plastic containers soften, as the food inside

gets hot. Boiling bags and tightly closed plastic

bags should be slit, pierced or vented as directed

on package.

Plastic wrap Microwave-safe only. Use to cover food during

cooking to retain moisture. Do not allow plastic

wrap to touch food.

Thermometers Microwave-safe only (meat and candy

thermometers).

Wax paper Use as a cover to prevent splattering and retain

moisture.

MATERIALS TO BE AVOIDED IN MICROWAVE OVEN

Aluminum tray May cause sparking. Transfer food into

microwave-safe dish.

Food carton May cause sparking. Transfer food into

with metal microwave-safe dish.

handle

Metal or Metal shields the food from microwave energy.

metal-trimmed Metal trim may cause sparking.

utensils

Metal twist ties May cause sparking and could cause a re in the

oven.

Paper bags May cause a re in the oven.

Styrofoam®Styrofoam® may melt or contaminate the liquid

inside when exposed to high temperature.

Wood Wood will dry out when used in the microwave

oven and may split or crack.

8

COUNTERTOP INSTALLATION

Remove all packing material and accessories. Examine the oven

for any damage such as dents or a broken door. Do not install if

oven is damaged.

Cabinet: Remove any protective lm found on the microwave oven

cabinet surface.

INSTALLATION

Select a level surface that provides enough open space for the intake

and/or outlet vents.

1. A minimum clearance of 3.0 inches (7.5cm) is required between

the oven and any adjacent walls. One side must be open.

(a) Leave a minimum clearance of 12 inches (30cm) above

the oven.

(b) Do not remove the legs from the bottom of the oven.

(c) Blocking the intake and/or outlet openings can damage the

oven.

(d) Place the oven as far away from radios and TV as possible.

Operation of microwave oven may cause interference to your

radio or TV reception.

2. Plug your oven into the appropriate outlet. Be sure the voltage

and the frequency is the same as the voltage and the frequency

on the rating label.

WARNING: Do not install oven over a range cooktop or other

heat-producing appliances. If installed near or over a heat source,

the oven could be damaged and the warranty would be void.

9

SETTING UP YOUR OVEN

Remove the oven and all materials from the carton and inside

the oven cavity. Your oven comes with an Instruction Manual.

Please keep it for reference.

C

BE

D

A) Control Panel

B) Observation Window

C) Door Assembly

D) Safety Interlock System

E) Ceramic Surface

1

2

3

4

5

6

7

A

CONTROL PANEL

1) Power Keys

2) Time Entry Key

3) X2 Key

4) Stop/Reset Key

5) Start Key

6) Number Keys

7) LED Display Screen

10

SPECIFICATIONS

Model WMO90

Rated Voltage: 120V ~ 60Hz

Rated Input Power 1550W

(Microwave):

Rated Output Power 1000W

(Microwave):

Oven Capacity: .9 cu. ft.

External Dimensions: 20.1 x 17 x 12.2 inches

Net Weight: Approx. 32.0 lbs.

OPERATION INSTRUCTION

Five power levels are available.

Level High Med-Hi Medium Defrost Hold

Power 100% 70% 50% 20% 0%

Display PL10 PL7 PL5 PL2 PL0

Appendix A. User Options

Items bolded below are the default values.

Option Setting Description

1 End of Cycle Tone OP:10 3 Beeps

OP:11 Continuous Beep

OP:12 5 Quick Beeps, Repeating

2 Beeper Volume OP:20 Off

OP:21 Low

OP:22 Medium

OP:23 High

3 Keybeep On/Off OP:30 Off

OP:31 On

4 Keypad Entry OP:40 15 Seconds

Window OP:41 30 Seconds

OP:42 60 Seconds

OP:43 120 Seconds

5 On the Fly OP:50 On-the-Fly Disabled

OP:51 On-the-Fly Enabled

11

6 Door Reset OP:60 Door Reset Disabled

OP:61 Door Reset Enabled

7 Max Time OP:70 60-Minute Maximum Cook Time

OP:71 10-Minute Maximum Cook Time

8 Manual Programming OP:80 Manual Programming Disabled

OP:81 Manual Programming Enabled

9 Double Digit OP:90 Single-Digit Mode, 10 Programs

OP:91 Double-Digit Mode, 100 Programs

Appendix B. Default Cook Times

The oven comes programmed with the following Preset Cook Times

unless otherwise noted in the Product Specications.

Button Cook Time Power Cook Factors

10:10 100% 80%

20:20 100% 80%

30:30 100% 80%

40:45 100% 80%

51:00 100% 80%

61:30 100% 80%

72:00 100% 80%

83:00 100% 80%

94:00 100% 80%

05:00 100% 80%

POWER UP

The display -- -- shows when the oven is powered ON for the rst time.

If the STOP button is pressed, the oven will change to Idle Mode.

Note: While in Idle Mode, no buttons can be pressed.

IDLE MODE

1) The oven enters Idle Mode after a number of seconds have

expired in Ready Mode without a keyboard button being

pressed or a door being opened and closed. The number

of seconds in Ready Mode is set by User Option 4 and is

displayed in the window.

2) During Idle Mode, LED is blank.

3) By opening and then closing the oven door, the oven will exit

Idle Mode and enter Ready Mode.

12

READY MODE

1) In this mode, the oven is ready to either begin a Manual or

Preset Program Cook Mode.

2) Opening and closing the door while the oven is in Idle Mode

will put the oven into Ready Mode.

3) During Ready Mode, 0:00 is displayed.

4) From Ready Mode, the oven can go into almost all of the

other modes.

DOOR OPEN MODE

1) While the door of the oven is open, the oven is in Door Open

Mode. This also allows for entry into Programming Mode.

2) Display is blank, but the fan and oven lamp are on.

3) If User Option OP:60 is selected and the door is opened

during operation, the oven will enter Pause Mode. Closing

the door will allow the Manual or Preset Program currently

running to continue.

4) If User Option OP:61 is selected, opening and closing the

door during operation will reset the oven and clear out any

information about the Manual or Preset Program currently

running.

PAUSE MODE

1) This mode allows the user to temporarily stop the cooking

cycle to inspect or stir food.

2) While in Manual Cook Mode, or Preset Program Cook Mode,

if the door is opened then closed, or if STOP is pressed, the

oven will enter Pause Mode.

3) While paused, LED will display the remaining cooking time.

4) Pause Mode reverts to Idle Mode in the same way as Ready

Mode, depending on User Option 4. Additionally, if STOP

is pressed, the oven will immediately enter Ready Mode.

If START is pressed, the oven will go into Working Mode.

MANUAL COOK ENTRY MODE

1) The user manually enters the cooking time and power level

while in this mode.

2) While the oven is in Ready Mode, press the TIME ENTRY pad

on the keyboard to enter Manual Cook Entry Mode.

13

3) In this mode, 00:00 is displayed. Press a number key to set

timer before choosing power level.

4) If you press HOLD 0%, Defrost 20%, Medium 50% or

Med-Hi 70% to choose a power level, the LED will display

your selection. If the same button is pressed twice, the

power will change to PL10, which is 100%. If no power is

chosen, PL10 is the default.

5) P ress START to enter Manual Cook Mode. Press STOP to

enter Ready Mode.

MANUAL COOK MODE

1) In this mode, food is cooked. While in Manual Cook Entry

Mode, pressing START begins the Manual Cook Mode.

2) The LED displays the remaining cooking time. The fan and

oven lamp will turn on.

3) When the cooking program is nished, the oven enters End

of Cook Cycle Mode. If you press STOP in this mode, the

oven enters Pause Mode.

END OF COOK CYCLE MODE

1) After the time has expired in the Manual Cook Mode, or the

Preset Program Cook Mode, the oven enters the End of

Cook Cycle Mode.

2) During this mode, End is displayed.

3) If either User Option OP:11 or OP:12 is selected, the oven

continues to sound until the user either opens and closes the

door or presses STOP. If User Option OP:10 is selected, after

the 3 beeps, the oven will display “End”. For a period of time

without any key operation, the oven will automatically enter

the Idle Mode.

PRESET PROGRAM COOK MODE

1) This mode cooks food using one touchpad operation.

While in Ready Mode, pressing one of 10 digital keys on

the keyboard will cause the oven to run the Preset Program

associated with that key.

2) The LED displays the remaining cooking time. With multi-

stage cooking, the total remaining cooking time is displayed,

and not the cooking time for any particular stage.

3) If the program chosen exceeds the maximum time allowed

by User Option 7, the oven will rapidly beep three times and

display ProG to indicate that the program is unacceptable.

14

4) When the cooking program is nished, the oven will enter

End of Cook Cycle Mode. If you press STOP in this mode,

the oven will enter Pause Mode.

ON-THE-FLY COOKING MODE

If User Option OP:51 is selected, this will allow the user to add time

while cooking.

1) Press the desired number key during cooking to add time.

The longer cooking cycle will begin automatically.

2) The screen displays the new remaining cooking time. When

cooking program is nished, the oven enters End of Cook

Cycle Mode.

3) To stop cooking before the end of the cooking cycle, press

STOP. The oven will enter Pause Mode.

PROGRAMMING MODE

This mode allows the user to assign cook times and power levels

using a one-touch button.

1) Open the door and press number button 1 for ve

seconds. The buzzer will sound once and the oven enters

Programming Mode.

2) ProG is displayed.

3) Press any number button, 0 to 9, and the LED will display the

saved time. You can then input the time you need.

4) Press HOLD 0%, Defrost 20%, Medium 50% or Med-Hi 70%

to input the power level. The LED will display the related

power. If the same button is pressed twice, the power will

change to PL10, which is the 100% power level. If no power

is chosen, PL10 is the default.

5) T o change the cooking factor: If you press X2, the LED

will display CF:XX. The default cooking factor is 80%, and

CF:80 is displayed. If you need to change the cooking factor,

just press one of the numbered buttons (1 for 10%, 2 for

20%, etc.).

6) After setting the time and power, press START, and the

cooking program will be saved. Once the program is saved,

ProG is displayed.

7) If total cooking time exceeds the MAX time, use User Option

7. Press START to save the program. The buzzer will sound

three times to indicate the oven is not in use. LED will display

ProG. The previous time set will remain in place.

15

8) Close the door to return oven to Ready Mode. If STOP is

pressed during the programming process, the oven will enter

Door Open Mode, and any program not saved will be lost.

If there is program saved as memory procedure, press the

related number button to start the programmed operation.

If nothing has been saved, the buzzer will sound and the

oven will not operate.

Example:

Program: Power level PL7, cooking time 1 minute and

25 seconds.

S tep 1: In waiting stage, press number button 1 for

5 seconds. ProG is displayed.

S tep 2: Press number 3. Program will be saved in 3.

S tep 3: Press numbers 1, 2 and 5 to program the

cooking time.

S tep 4: Press Med-Hi 70% button. PL7 is displayed.

S tep 5: Press START to save. When using the program next

time, just press 3, and the saved program will start.

Note:

1. If the electricity is cut off, the saved program will not be lost.

2. If the program needs to be reset, repeat the above steps.

3. I f STOP is pressed instead of START at the last step, the

oven will go into Door Open Mode, and the program setting

will not be saved.

DOUBLE QUANTITY COOKING

Allows the user to double the set cooking time of a particular

food item.

1) In the Ready mode, press the X2 key before or after pressing

the desired preprogrammed key. LED displays doub.

2) If you wish to change the Cooking Factor, see Programming

Mode.

3) The oven will begin to cook.

4) At the end of the cooking program, the oven will enter End

of Cook Cycle Mode.

16

TO PROGRAM MULTI-STAGE COOKING

Users can cook food items with different combinations of time and

power levels. Up to three stages can be set in Cooking Mode or

Memory Mode.

1) Once power level and time are set for the rst stage:

Pressing TIME ENTRY (S-2 is displayed) lets you program the

power level and time for stage two.

2) Pressing TIME ENTRY again (S-3 is displayed) lets you

program a third power level and time combination.

3) Press START to start cooking.

Example:

STAGE ONE

a. Press number button 1 for ve seconds. LED displays ProG.

b. Press number button 3 to save the program in 3.

c. Enter desired cook time.

d. Press Med-Hi 70%. Display shows PL7.

The rst stage is nished.

STAGE TWO

a. Press TIME ENTRY. Display shows S-2.

b. Enter desired cook time.

c. Press Medium 50%. Display shows PL5.

The second stage is nished.

d. Press START to save the two-stage program, or press TIME

ENTRY once more to program a third stage.

USER OPTION MODE

This allows the user to choose between various ways for the oven

to operate.

1) Open the oven door and press number button 2 for ve

seconds. The buzzer sounds once and this mode is entered.

2) LED displays OP: - -.

3) Press any number button to enter related mode setting.

For example: To set the buzzer to a medium level, press

2. Display shows OP:22. To change, keep pressing 2. LED

displays cycles through OP:20, OP:21, OP:22, OP:23, before

cycling back to OP:20.

17

4) Press START to save the displayed setting. OP: - - will be

displayed again.

5) D uring this process, press STOP to enter Door Open Mode.

Closing the door will return oven to Ready Mode.

6) If START button is not pressed as the last step, the program

will not be saved.

SERVICE MODE

1) Open the oven door and press and hold the number button

3 for ve seconds to enter Service Mode.

2) LED displays SErU.

3) To check the times of closing or opening the door, just

press 3. LED will display the times.

4) To reset: Press and hold both START and the number button

4. In seconds, the message will be cancelled and 4-CL will

be displayed.

5) P ress STOP to enter Door Open Mode. Close the door to

enter Ready Mode.

INQUIRY FUNCTION

While cooking, press TIME ENTRY to check the power level. The LED

will display the power level for 3 seconds. This feature is available for

multi-stage cooking.

FACTORY-DEFAULT SETTING

Press START and 0. Then press START to return to factory-default

settings.

18

CLEANING INSTRUCTIONS

Always keep the oven clean.

1. Cleaning the glass viewing window, the inner door panel

and oven front face: For best performance and to maintain

a high degree of safety, the inner door panel and oven front

face should be free of food or grease buildup. Wipe these

parts with a mild detergent, rinse and wipe dry. Never use

abrasive powders or pads.

2. Cleaning the control panel and plastic parts: Do not apply

a detergent or an alkaline liquid spray to the control panel

and plastic parts, as this may cause damage to these parts.

Use a dry cloth (not a soaked cloth) to clean these parts.

3. Cleaning the oven interior: After use, be sure to clean up

spilled liquids, spattered oil and food debris as quickly as

possible. If the oven is used when dirty, efciency drops and

the dirt gets stuck on the oven surface and may cause bad

odors. Clean the interior with a cloth soaked in lukewarm

water with a mild detergent dissolved in it, then rinse the

soap off with a damp cloth.

CAUTION: Do not wipe plastic and painted sections of the oven with

bleach, thinners or other cleaning agents, as this may cause these

parts to dissolve or change shape.

MAINTENANCE

Troubleshooting

Reference the chart below for any operating issues and try the

solutions provided. If the microwave oven still does not work properly,

contact the nearest authorized service center.

TROUBLE POSSIBLE CAUSE POSSIBLE REMEDY

Oven will not start a. Electrical cord a. Plug into the outlet.

for oven is not b. C lose the door and

plugged in. try again.

b. Door is open. c. Check instructions.

c. Wrong operation

is set.

19

TROUBLE POSSIBLE CAUSE POSSIBLE REMEDY

Sparking a. Materials to a. Use microwave-safe

be avoided in cookware only.

microwave oven b. D o not operate with

were used. oven empty.

b. T he oven is c. Clean cavity with a

operating when wet cloth.

empty.

c. Spilled food remains

in the cavity.

Unevenly cooked a. M aterials to a. U se microwave-safe

foods be avoided in cookware only.

microwave oven b. Co mpletely defrost

were used. food.

b. F ood is not c. Use correct cooking

defrosted time, power level.

completely. d. Turn or stir food.

c. Cooking time, power

level is not suitable.

d. Food is not turned

or stirred.

Overcooked foods Cooking time, power Use correct cooking

level is not suitable. time, power level.

Undercooked foods a. Materials to a. U se microwave-safe

be avoided in cookware only.

microwave oven b. Co mpletely defrost

were used. food.

b. F ood is not c. Check to see that

defrosted oven ventilation ports

completely. are not restricted.

c. Oven ventilation d. Use correct cooking

ports are restricted. time, power level.

d. Cooking time, power

level is not suitable.

Improper defrosting a. Materials to a. Use microwave-safe

be avoided in cookware only.

microwave oven b. U se correct cooking

were used. time, power level.

b. C ooking time, power c. Turn or stir food.

level is not suitable.

c. Food is not turned

or stirred.

20

MEDIDAS DE SEGURIDAD

IMPORTANTES

1.

LEA TODAS LAS INSTRUCCIONES ANTES

DEL USO.

2. Lea y siga cuidadosamente las “PRECAUCIONES PARA

EVITAR LA EXPOSICIÓN EXCESIVA A LAS MICROONDAS”

en la página 23.

3. Al igual que con la mayoría de los aparatos de cocción, es

necesario vigilar la cocción de cerca para reducir el riesgo de

incendio dentro del horno.

ADVERTENCIA: Para reducir el riesgo de incendio dentro del horno:

i) No cocine demasiado los alimentos. Vigile la cocción con

cuidado cuando use papel, plástico u otros materiales

combustibles para facilitar la cocción.

ii) Q uite las ataduras de alambre de las bolsas de papel/

plástico antes de meter estas al horno.

iii) Si los materiales en el horno se prenden, mantenga la puerta

cerrada, apague y desenchufe el aparato.

iv) No use el horno para fines de almacenamiento. No deje

artículos de papel, utensilios de cocina ni alimentos en el

horno cuando no esté en uso.

4. Este aparato debe estar puesto a tierra. Conéctelo a una toma

de corriente debidamente puesta a tierra. Véase la sección

“INSTRUCCIONES DE PUESTA A TIERRA” en la página 22.

5. Instale y ubique el aparto según se describe en las

instrucciones de instalación provistas en la página 26.

6. Algunos alimentos herméticos (p. ej., los huevos enteros) o

recipientes cerrados (p. ej., tarros de vidrio cerrados) pueden

explotar al calentarse en un horno de microondas y no se

deben calentar con este aparato.

ADVERTENCIA: Para reducir el riesgo de incendio, descarga

eléctrica, heridas o exposición excesiva a las microondas, debe

tomar precauciones básicas de seguridad, entre ellas las siguientes:

7. Use este aparato únicamente con el propósito para el cual

fue diseñado y solamente según las instrucciones. No use

productos químicos corrosivos o productos que produzcan

vapores corrosivos en este aparato. Este aparato ha sido

especialmente diseñado para recalentar, cocinar y deshidratar

alimentos. No ha sido diseñado para uso industrial o de

laboratorio.

La page charge ...

Waring Commercial WMO90 Manuel utilisateur

Waring Commercial WMO90 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents