PROPOINT 8843997 Le manuel du propriétaire

Catégorie
Coupe-bordures
Taper
Le manuel du propriétaire
V1.0 8843997
Please read and understand all instructions before use. Retain this manual for future
reference.
AIR IMPACT WRENCH
3/8 IN.
8843997 3/8 in. Air Impact Wrench V1.0
2 For technical questions call 1-800-665-8685
SPECIFICATIONS
Square Drive Size 3/8 in.
Max. Torque 350 ft-lb
Speed Rating 13,000 RPM
Average CFM @ 15 Second Run Time 5.7 CFM
CFM @ Full Load 22 CFM
Pressure Rating 90 PSI
Air Inlet 1/4 in.
Material Composite housing with cushion grip
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this manual.
A notice is an alert that there is a possibility of property damage, injury
or death if certain instructions are not followed.
DANGER! This notice indicates an immediate and specific hazard that
will result in severe personal injury or death if the proper
precautions are not taken.
WARNING! This notice indicates a specific hazard or unsafe practice
that could result in severe personal injury or death if the
proper precautions are not taken.
CAUTION! This notice indicates a potentially hazardous situation that
may result in minor or moderate injury if proper practices are
not taken.
NOTICE! This notice indicates that a specific hazard or unsafe
practice will result in equipment or property damage, but
not personal injury.
V1.0 3/8 in. Air Impact Wrench 8843997
Visit www.princessauto.com for more information 3
INTRODUCTION
This 3/8 in. Air Impact Wrench has a composite housing with a cushion
grip and maximum torque of 350 ft/lb. The tool has variable torque in
forward and reverse.
SAFETY
WARNING! Read and understand all instructions before using this
tool. The operator must follow basic precautions to reduce the
risk of personal injury and/or damage to the equipment.
Keep this manual for safety warnings, precautions, operating or
inspection and maintenance instructions.
WORK AREA
1. Operate in a safe work environment. Keep your work area clean,
well-lit and free of distractions. Place lights so you are not working
in a shadow.
2. Keep anyone not wearing the appropriate safety equipment away
from the work area.
3. Store tools properly in a safe and dry location. Keep tools out of
the reach of children.
4. Do not install or use in the presence of flammable gases, dust or
liquids.
PERSONAL SAFETY
WARNING! Wear personal protective equipment approved by the
Canadian Standards Association (CSA) or American National
Standards Institute (ANSI).
PERSONAL PROTECTIVE EQUIPMENT
1. Always wear impact safety goggles that provide front and side
protection for the eyes. Eye protection equipment should comply
with CSA Z94.3-07 or ANSI Z87.1 standards based on the type of
work performed.
2. Wear the appropriate type of full-face shield in addition to safety
googles, as the work can create chips, abrasive or particulate matter.
3. Wear gloves that provide protection based on the work materials or
to reduce the effects of tool vibration.
8843997 3/8 in. Air Impact Wrench V1.0
4 For technical questions call 1-800-665-8685
3.1 Do not wear gloves when operating a tool that can snag the
material and pull the hand into the tool.
4. Wear protective clothing designed for the work environment and
tool.
5. Non-skid footwear is recommended to maintain footing and
balance in the work environment.
6. This tool can cause hearing damage. Wear hearing protection gear
with an appropriate Noise Reduction Rating to withstand the
decibel levels.
7. The tool may contain high pressure. Use safety glasses and gloves
for protection during operation. Keep hands clear of the exposed
rubber portions of the hose.
PERSONAL PRECAUTIONS
Control the tool, personal movement and the work environment to avoid
personal injury or damage to the tool.
1. Do not operate any tool when tired or under the influence of drugs,
alcohol or medications.
2. Avoid wearing clothes or jewelry that can become entangled with
the moving parts of a tool. Keep long hair covered or bound.
3. Do not overreach when operating a tool. Proper footing and
balance enables better control in unexpected situations.
4. Keep your fingers away from the trigger/switch while carrying the
tool, attaching an air hose or an accessory. Lock the trigger/switch
safety if available.
5. Avoid unintentional starts. Be sure that the regulator/throttle switch
is in the neutral or OFF position when not in use and before
connecting it to any air source.
6. Never point the air stream or tool at any point of your body, other
people or animals. Debris and dust ejected at high speed can
cause an injury.
7. Serious injury or death may occur from inhaling compressed air. The air
stream may contain carbon monoxide, toxic vapors or solid particles.
Never inhale compressed air directly from the pump or air tool.
8. Support the workpiece or clamp it to a stable platform. Holding the
workpiece by hand or against your body may lead to personal injury.
V1.0 3/8 in. Air Impact Wrench 8843997
Visit www.princessauto.com for more information 5
9. Securely hold this tool using both hands. Using a tool with only one
hand can result in loss of control.
SPECIFIC SAFETY PRECAUTIONS
WARNING! DO NOT let comfort or familiarity with product (gained
from repeated use) replace strict adherence to the tool safety rules.
If you use this tool unsafely or incorrectly, you can suffer serious
personal injury.
1. Use the correct tool for the job. This tool was designed for a
specific function. Do not modify or alter this tool or use it for an
unintended purpose.
2. Do not use the tool if any parts are damaged, broken or misplaced.
Repair or replace the parts.
3. Do not use any power tool with a malfunctioning power switch or
control. A power tool that fails to respond to the controls is
dangerous and can cause an injury. A qualified technician must
repair and verify the power tool is operating correctly before it can
be used.
4. Never use a tool with a cracked or worn tool accessory. Change
the tool accessory before using it.
5. Never operate the tool when the safety guard is removed or
broken. Never clamp or tie the guard into the open position.
6. Do not cover the air vents.
7. Only use accessories that are specifically designed for use with the
tool. Ensure the accessory is tightly installed.
8. Only use an accessory that exceeds the speed rating (see
Specifications).
9. Disconnect the power source before installing or servicing the tool.
10. Remove adjusting keys and wrenches before using the tool. The
tool may eject an attached wrench or a key and cause an injury to
you or a bystander.
11. Before using the tool on a workpiece, test the tool by running it at
the highest speed rating for at least 30 seconds in a safe position.
Stop immediately if there is any abnormal vibration or wobbling.
Check the tool to determine the cause.
8843997 3/8 in. Air Impact Wrench V1.0
6 For technical questions call 1-800-665-8685
12. Never force the tool. Excessive pressure could break the tool,
resulting in damage to your workpiece or serious personal injury.
Excessive pressure is the cause if your tool runs smoothly under no
load, but roughly under load.
13. Keep hands and fingers away from the work area. Any part of the
body contacting the tools working parts could result in an injury.
14. Never touch the tool accessory or workpiece during or immediately
after use. They may be hot and could inflict a burn injury.
15. Do not place the tool down until the tools accessory has stopped
moving. The accessory may catch the surface of work material and
wrench itself free, causing injury to the user or others in the work area.
16. Never hold the drive, socket, drive extension or accessories during
impacting. Doing so increases the risk of cuts, burns or vibration
injuries.
17. Use a torque bar or forearm brace to absorb reaction torque above
10-Nm to protect against a twist injury.
AIR TOOL PRECAUTIONS
1. Use only clean and dry compressed air as a power source.
Contaminated or moist air will gradually damage the tool.
2. Install an in-line shutoff valve or regulator to allow immediate control
over the air supply in an emergency, even if a hose is ruptured.
3. Discontinue tool use if it does not work properly or air is leaking.
Tag or mark the tool as defective’ or out of serviceuntil repaired.
4. Check the manufacturers maximum pressure rating for air tools
and accessories. Compressor outlet pressure must be regulated to
never exceed the maximum pressure rating of the tool (see
Specifications). Exceeding the maximum PSI rating can create a
bursting hazard, causing injury and property damage.
4.1 Do not exceed maximum working air pressure at 90 PSI
(6.2 bar).
5. Attach all accessories properly to the tool before connecting the air
supply. A loose accessory may detach or break during operation.
6. Never use oxygen, combustible gas or any other bottled gas as a
power source. Any power source other than an air compressor
could cause an explosion and serious personal injury.
V1.0 3/8 in. Air Impact Wrench 8843997
Visit www.princessauto.com for more information 7
7. Turn OFF the valve and discharge any remaining air pressure after
each use or before adjusting the tool.
8. Do not leave the air tool unattended with its compressed air supply
on. Turn off the compressed air supply and bleed the air tool of any
remaining compressed air before leaving the air tool unattended.
9. Serious injury may occur from loose debris being propelled at high
speeds from the compressed air stream. Always wear OSHA
approved safety glasses to protect the eyes during operation of the air
compressor.
10. Always turn off the air compressor and drain tank pressure
completely before attempting maintenance or attaching air tools.
Release pressure slowly from the system.
AIR HOSE PRECAUTIONS
1. Inspect the tool's air hose for cracks, fraying or other faults before
each use. Discontinue use if the air hose is damaged or hissing is
heard from the air hose or couplers. Replace the defective air
hose.
2. Do not allow people, mobile equipment or vehicles to pass over the
unprotected air hose. Position the air hose away from high traffic
areas, in a reinforced conduit or place planks on both sides of the
air hose to create a protective trench.
3. Prevent damage to the air hose by observing the following:
3.1 Never carry the tool by the air hose.
3.2 Keep the air hose behind the tool and out of the tool's work
path.
3.3 Keep the air hose away from heat, oil, sharp edges or moving
parts.
3.4 Do not wrap the air hose around the tool as sharp edges may
pierce or crack the air hose. Gently coil the hose and either
hang on a hook or fasten with a device to keep hose together
when storing.
4. A damaged or disconnected air hose under pressure may whip
around and inflict personal injury or damage the work area. Secure
the compressor's air hose to a fixed or permanent structure with
clamps or cable ties.
8843997 3/8 in. Air Impact Wrench V1.0
8 For technical questions call 1-800-665-8685
5. Before connecting the hose, clean the hose by blowing out with
compressed air. This will prevent moisture and/or dust in the hose
from entering the tool causing rust and/or malfunction.
VIBRATION PRECAUTIONS
1. This tool vibrates during use. Repeated or long-term exposure to
vibration may cause temporary or permanent physical injury. Take
frequent breaks when using the tool.
2. If you feel any medical symptoms related to vibrations (such as
tingling, numbness, and white or blue fingers), seek medical
attention as soon as possible.
3. Wear suitable gloves to reduce the effects of vibration.
4. DO NOT use this tool before consulting a physician if one of the
following applies:
a. Pregnant
b. Impaired blood circulation to
the hands
c. Past hand injuries
d. Nervous system disorders
e. Diabetes
f. Raynaud's Disease
5. Do not use worn or ill-fitting sockets or extensions as this is likely to
cause a substantial increase in vibration.
UNPACKING
WARNING! Do not operate the tool if any part is missing. Replace
the missing part before operating. Failure to do so could result in
a malfunction and personal injury.
Remove the parts and accessories from the packaging and inspect for
damage.
ASSEMBLY & INSTALLATION
Dashed numbers in parenthesis (Fig. 1-1) refer to a specific point in an
illustration or image.
INSTALL AIR COUPLER PLUG
Prepare a standard 1/4 in. NPT coupler plug (sold separately) for use
with your tool.
1. Wrap the external threads of the coupler plug with sealant tape.
V1.0 3/8 in. Air Impact Wrench 8843997
Visit www.princessauto.com for more information 9
1.1 Wrap tape in a clockwise direction so it will not unravel.
1.2 Do not tape all the threads. Leave several leading threads
unwrapped for easier alignment.
2. Screw the coupler plug into the tool's air inlet and tighten with a
wrench until snug.
3. Run the compressor at a low volume and check the connection for
air leaks. Do not use the tool until all air leaks are repaired or the
faulty component is replaced.
IMPORTANT! Vibration may cause failure if a quick coupler is
connected directly to the air tool. To overcome this, connect a
leader hose to the tool. A quick coupler may then be used to
connect the leader hose to the air line hose.
OPERATION
CAUTION! Injury Hazard! To avoid injury, always disconnect the air
supply to the tool when attaching or removing sockets or accessories.
Use only sockets and accessories rated for impact use.
1. Disconnect the air supply.
2. Snap the socket or accessory over the retaining ring nested in the
square drive.
3. Connect the air supply, hold the tool securely and press the trigger
to begin the rotating action.
4. To loosen fasteners, move the lever (Fig. 1-1) on the back of the
drive head counter-clockwise to align the
arrow to the reverse arrow (Fig. 1-2).
5. To tighten fasteners, move the lever
clockwise and align the arrow to select
either low (Fig. 1-3), medium (Fig. 1-4),
or high torque (Fig. 1-5) settings (small,
medium or large circles).
6. Place the socket over the fastener, grip the impact wrench firmly
with both hands and gently squeeze the trigger.
6.1 If the tool stalls while tightening, do not raise the output
pressure of the air compressor above 90 PSI. Pressure above
90 PSI will strip the workpiece and damage the tool,
Fig. 1
8843997 3/8 in. Air Impact Wrench V1.0
10 For technical questions call 1-800-665-8685
potentially causing tool failure and serious injury. Use other
appropriate methods and tools to tighten the nut.
7. This tool will stop operation/rotation a few seconds after the trigger
is released.
8. When the fastener is tightened, release the trigger and remove the
tool and socket.
9. Use a mechanical torque wrench to check the fastener torque.
10. When finished with the tool, turn off the air compressor, disconnect
the air hose and discharge any residual air remaining in the tool.
Put the impact wrench away in a safe storage area.
PRESSURE DROP
Apply the air consumption and pressure rate numbers to the tools air
inlet, not the compressors outlet. Calculate the pressure drop for your
air supply set-up and increase the compressor outlet pressure to
compensate. Make sure you do not exceed the maximum pressure for
any part of your air supply system.
Installing a pressure gauge at the tool inlet is the best way to measure
the air pressure and adjust the compressors output.
CARE & MAINTENANCE
1. Maintain the tool with care. A tool in good condition is efficient,
easier to control and will have fewer problems.
2. Inspect the tool fittings, alignment and hoses periodically. Have
damaged or worn components repaired or replaced by an authorized
technician. Only use identical replacement parts when servicing.
3. Follow instructions for lubricating and changing accessories.
4. Only use accessories intended for use with this tool.
5. Keep the tool clean, dry and free from oil/grease at all times.
6. Maintain the tools labels and name plates. These carry important
information. If unreadable or missing, contact Princess Auto Ltd. for
replacements.
WARNING! Only qualified service personnel should repair the
tool. An improperly repaired tool may present a hazard to the
user and/or others.
V1.0 3/8 in. Air Impact Wrench 8843997
Visit www.princessauto.com for more information 11
AIR TOOL LUBRICATION
NOTICE! Only use air tool oil to lubricate the tool. Other
lubricants are not suitable and will damage the tool or cause a
malfunction during use.
NOTICE! Never use a penetrating oil to lubricate an air tool.
Penetrating oil acts as a solvent that will dissolve the tools
grease packing and may damage the o-rings, causing the tool to
seize or malfunction.
1. All air tools have an internal coating of grease to prevent corrosion
during shipping and storage. Remove this grease by adding a
generous amount of air tool oil in the air inlet and then run the tool
under no load until the exhaust is clear.
2. Manually add a drop or two of air tool oil into the tools coupler
plug before each use and after every hour of continuous use. The
tool will not work properly without lubrication and parts will wear
prematurely.
3. Avoid adding too much air tool oil as this can cause premature
power loss and eventual tool failure. A qualified technician will need
to take the tool apart and clean out the excess oil.
4. Apply a generous amount of air tool oil to the tool before storing it
for an extended period of time (overnight, weekend, etc.). Run the
tool for approximately 30 seconds to ensure the oil is evenly
distributed throughout the tool. Store it in a clean and dry location.
DISPOSAL
Recycle a tool damaged beyond repair at the appropriate facility.
Contact your local municipality for a list of disposal facilities or by-laws for
electronic devices, batteries, oil or other toxic liquids.
IMPORTANT! DO NOT pollute the environment by allowing
uncontrolled discharge of waste oil.
TROUBLESHOOTING
Visit a Princess Auto Ltd. location for a solution if the tool does not
function properly or parts are missing. If unable to do so, have a
qualified technician service the tool.
8843997 3/8 in. Air Impact Wrench V1.0
12 For technical questions call 1-800-665-8685
PROBLEM(S) POSSIBLE CAUSE(S) SUGGESTED SOLUTION(S)
Tool runs at
normal
speed, but
loses power
under load.
Motor parts worn. 1. Have a qualified technician service
the tool.
2. Replace tool or parts.
Tool runs
slowly. Air
flows slightly
from exhaust.
Motor parts jammed
with dirt particles.
OR
Airflow blocked by dirt.
1. Check air inlet filter for blockage.
2. Pour air tool lubricating oil into air
inlet as per lubrication instructions
for clearing shipping grease.
3. Operate tool in short bursts to
clear debris.
4. If tool still jammed, clean tool and
lubricate per lubrication
instructions.
Tool runs
slowly. Air
flows slightly
from exhaust.
1. Air regulator in
closed position.
2.
Damage or excessive
wearing of internal
parts.
1. Open the air regulator to desired
airflow.
2a. Have a qualified technician
service the tool.
2b. Replace tool or parts.
Tools will not
run. Air flows
freely from
exhaust.
Damage or excessive
wearing of internal parts.
1. Have a qualified technician
service the tool.
2. Replace tool or parts.
Tool will not
shut off.
1. Throttle valve o-ring
dislodged from inlet
valve seat.
2. Trigger mechanism
jammed or dirty.
1. Replace throttle valve
o-rings.
2. Clean trigger mechanism and
lubricate.
Loss of
power or
erratic
performance.
1. Excessive drain on
the air hose.
Incorrect size or type
of hose connectors.
2. Moisture or
restriction
in the air hose/tank
3. Air compressor has
insufficient flow.
1. Check the air hose
and confirm the
hose fitting is correct for the inlet
bushing.
2. Depressurize system and drain
tank and air hose of water.
3. Ensure tool is connected to a
compressor with a rate flow that
matches the tool.
V1.0 3/8 in. Air Impact Wrench 8843997
Visit www.princessauto.com for more information 13
PARTS BREAKDOWN
PARTS LIST
#
QTY
1 Motor Housing Assembly
(including 38)
1
2
1
3 O-ring 1
4 Exhaust Deflector 1
5 O-Ring 2
6 Spring 1
7 Throttle Valve Assembly
(including 7-1 and 7-2)
1
7-1
Throttle Valve Pin
1
7-2 Throttle Valve 1
8 Throttle Valve Seat 1
9 O-Ring 1
10 Trigger Assembly
(including 11 and 12)
1
11 Trigger Pin 1
12 O-Ring 1
13 Spring Pin 1
14 Gasket 1
8843997 3/8 in. Air Impact Wrench V1.0
14 For technical questions call 1-800-665-8685
15 O-Ring 1
16
1
17 Forward/Reverse Lever 1
18
1
19 Rear Housing 1
21 Ball Bearing 1
22 Rear End Plate 1
23 Rotor 1
24 Rotor Blade 6
25 Spring Pin 3
26 Cylinder 1
27 Front End Plate 1
28 Ball Bearing 1
29 Gasket 1
30 Hammer Frame 1
31 Hammer 2
32
2
33 Anvil 1
34
O-Ring
1
35 Socket Retainer 1
36
Bushing
1
37 Hammer Case Assembly
(including 36 and 45)
1
38 Bushing 1
39 Screw 4
40 Pin 1
41 Spring 1
42 Muffler Element 1
43 Spacer 1
44 Screw 1
45 Grease Fitting 1
TK Tune-up Kit (including
3.5(2), 6, 9, 14, 15, 17,
18, 24(6), 29, 34, 35,
41, 42)
V1.0 3/8 in. Air Impact Wrench 8843997
Visit www.princessauto.com for more information 15
8843997 3/8 in. Air Impact Wrench V1.0
16 For technical questions call 1-800-665-8685
V1,0 8843997
Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil. Conservez ce
manuel afin de pouvoir le consulter plus tard.
CLÉ À CHOCS
PNEUMATIQUE
3/8 PO
8843997 Clé à chocs pneumatique de 3/8 po V1,0
2 En cas de questions techniques, appelez le 1-800-665-8685
SPÉCIFICATIONS
Format de prise carrée 3/8 po
Couple max. 350 pi-lb
Vitesse nominale 13 000 tr/min
Débit moyen à un temps de
fonctionnement de 15 secondes
5,7 pi cubes/min
Débit à pleine charge 22 pi cubes/min
Pression nominale 90 lb/po car
Entrée dair 1/4 po
Matériau Boîtier en composite avec prise coussinée
DÉFINITIONS DE DANGER
Veuillez-vous familiariser avec les avis de danger qui sont présentés dans
ce manuel. Un avis est une alerte indiquant qu'il existe un risque de
dommage à la propriété, de blessure ou de décès si on ne respecte pas
certaines instructions.
DANGER ! Cet avis indique un risque immédiat et particulier qui
entraînera des blessures corporelles graves ou
même la mort si on omet de prendre les précautions
nécessaires.
AVERTISSEMENT ! Cet avis indique un risque particulier ou une pratique
non sécuritaire qui pourrait entraîner des blessures
corporelles graves ou me la mort si on omet de
prendre les précautions nécessaires.
ATTENTION ! Cet avis indique une situation possiblement
dangereuse qui peut entraîner des blessures
mineures ou modérées si on ne procède pas de la
façon recommandée.
AVIS ! Cet avis indique un risque particulier ou une pratique
non sécuritaire qui entraînera des dommages au
niveau de l'équipement ou des biens, mais non des
blessures corporelles.
V1,0 Clé à chocs pneumatique de 3/8 po 8843997
Visitez www.princessauto.com pour plus d'informations 3
INTRODUCTION
Cette clé à chocs pneumatique en composite à prise de 3/8 po
possède un boîtier en composite avec une prise coussinée et un couple
maximal de 350 pi-lb. Loutil possède un couple variable en marche
avant et en marche arrière.
SÉCURITÉ
AVERTISSEMENT ! Veuillez lire et comprendre toutes les
instructions avant d'utiliser cet outil. L'utilisateur doit respecter
les précautions de base lorsqu'il utilise cet outil afin de réduire
le risque de blessure ou de dommage à l'équipement.
Conservez ce manuel qui contient les avertissements de sécurité, les
précautions, les instructions de fonctionnement ou d'inspection et
d'entretien.
AIRE DE TRAVAIL
1. Travaillez dans un environnement de travail sécuritaire. Gardez
votre aire de travail propre, bien éclairée et exempte de toute
distraction. Placez les lampes de fon à ne pas travailler dans
l’ombre.
2. Assurez-vous que les personnes qui ne portent pas l'équipement de
sécurité approprié ne se trouvent pas à proximité de l'aire de travail.
3. Rangez les outils correctement dans un lieu sécurisé et sec.
Gardez les outils hors de la portée des enfants.
4. N'installez pas et n'utilisez pas d'outils électriques en présence de
gaz, de poussière ou de liquides inflammables.
SÉCURITÉ PERSONNELLE
AVERTISSEMENT ! Portez de l'équipement de protection personnelle
homologué par l'Association canadienne de normalisation (CSA) ou
l'American National Standards Institute (ANSI).
ÉQUIPEMENT DE PROTECTION PERSONNELLE
1. Portez toujours des lunettes antiprojections qui offrent une
protection frontale et latérale pour les yeux. L'équipement de
protection des yeux devrait être conforme à la norme CSA Z94.3-
07 ou ANSI Z87.1 fonction du type de travail effectué.
8843997 Clé à chocs pneumatique de 3/8 po V1,0
4 En cas de questions techniques, appelez le 1-800-665-8685
2. Portez un écran facial panoramique de type approprié avec les
lunettes de sécurité puisque cette tâche peut créer des copeaux,
des matières abrasives ou des particules.
3. Portez des gants qui protègent en fonction des matériaux de travail
et pour réduire les effets des vibrations de l'outil.
3.1 Ne portez pas de gants lorsque vous utilisez un outil dans
lequel le tissu pourrait demeurer coincé, entraînant ainsi la
main.
4. Portez des vêtements de protection conçus pour l'environnement
de travail et pour l'outil.
5. Les chaussures antidérapantes sont recommandées pour maintenir
la stabilité et l'équilibre au sein de l'environnement de travail.
6. Cet outil peut causer des dommages à l'ouïe. Portez un dispositif
de protection anti-bruit présentant une cote de réduction du bruit
adéquate en fonction du niveau de décibels.
7. L’outil peut être à haute pression. Portez des lunettes de sécurité et
des gants pour vous protéger au cours de l'opération. Gardez les
mains à l'écart des parties de caoutchouc exposées du tuyau.
PRÉCAUTIONS PERSONNELLES
1. N'utilisez pas l'outil si vous êtes fatigué ou sous l'effet de drogues,
d'alcool ou de médicaments.
2. Évitez de porter des vêtements ou des bijoux pouvant se prendre dans
les pièces mobiles d'un outil. Gardez les cheveux longs recouverts ou
attachés.
3. N'utilisez pas l'outil si vous devez étirer les bras pour vous en
servir. Une stabilité et un équilibre appropriés sont nécessaires afin
d'avoir un meilleur contrôle en cas de situations inattendues.
4. Gardez vos doigts à bonne distance de la gâchette/commutateur
lors du transport de loutil ou du branchement dun tuyau à air ou
d’un accessoire. Engagez le verrou de gâchette/interrupteur, le cas
échéant.
5. Évitez les mises en marche involontaires. Assurez-vous que le
régulateur/commutateur est en position neutre ou OFF (arrêt)
lorsque loutil nest pas utilisé et avant de le brancher à une source
d’air.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

PROPOINT 8843997 Le manuel du propriétaire

Catégorie
Coupe-bordures
Taper
Le manuel du propriétaire

dans d''autres langues