PROPOINT 8849507 Le manuel du propriétaire
- Catégorie
- Outils électroportatifs
- Taper
- Le manuel du propriétaire
V1.0 8849507
Please read and understand all instructions before use. Retain this manual for future
reference.
AIR RATCHET
3/8 IN.
8849507 3/8 in. Air Ratchet V1.0
2 For technical questions call 1-800-665-8685
SPECIFICATIONS
Air Inlet 1/4 in.
Square Drive Size 3/8 in.
Pressure Range 70 to 90 PSI
Air Consumption 4.5 CFM
CFM @ Full Load (CFM) 18 CFM
Max. Torque 75 ft-lb
Torque Range 25 to 75 ft-lb
Speed Rating 450 RPM
Min. Hose Size 3/8 in.
Material Die-cast Aluminum Housing
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this manual.
A notice is an alert that there is a possibility of property damage, injury
or death if certain instructions are not followed.
DANGER! This notice indicates an immediate and specific hazard
that will result in severe personal injury or death if the
proper precautions are not taken.
WARNING! This notice indicates a specific hazard or unsafe practice
that could result in severe personal injury or death if the
proper precautions are not taken.
CAUTION! This notice indicates a potentially hazardous situation that
may result in minor or moderate injury if proper practices
are not taken.
NOTICE! This notice indicates that a specific hazard or unsafe
practice will result in equipment or property damage, but
not personal injury.
V1.0 3/8 in. Air Ratchet 8849507
Visit www.princessauto.com for more information 3
INTRODUCTION
The 3/8 in. Air Ratchet can loosen or tighten nuts and bolts with 25 to 75
ft-lb of power. The reactionless drive absorbs the impact force to reduce
fatigue and strain on the user’s wrist.
SAFETY
WARNING! Read and understand all instructions before using this
tool. The operator must follow basic precautions to reduce the
risk of personal injury and/or damage to the equipment.
Keep this manual for safety warnings, precautions, operating or
inspection and maintenance instructions.
WORK AREA
1. Operate in a safe work environment. Keep your work area clean, well-
lit and free of distractions. Place lights so you are not working in a
shadow.
2. Keep anyone not wearing the appropriate safety equipment away
from the work area.
3. Store unused tools properly in a safe and dry location to prevent
rust or damage. Lock tools away and keep out of the reach of
children.
PERSONAL SAFETY
WARNING! Wear personal protective equipment approved by the
Canadian Standards Association (CSA) or American National
Standards Institute (ANSI).
PERSONAL PROTECTIVE EQUIPMENT
1. Always wear impact safety goggles that provide front and side
protection for the eyes. Eye protection equipment should comply
with CSA Z94.3-07 or ANSI Z87.1 standards based on the type of
work performed.
2. The tool may contain high pressure. Use safety glasses and gloves
for protection during operation. Keep hands clear of the exposed
rubber portions of the hose.
3. Wear the appropriate type of full-face shield in addition to safety
googles, as the work can create chips, abrasive or particulate matter.
4. Wear protective clothing designed for the work environment and tool.
8849507 3/8 in. Air Ratchet V1.0
4 For technical questions call 1-800-665-8685
5. Wear the appropriate rated dust mask or respirator.
6. This tool can cause hearing damage. Wear ear protection gear to
eliminate or reduce the noise. If possible add a muffling device to
the air tool’s exhaust.
PERSONAL PRECAUTIONS
Control the tool, personal movement and the work environment to avoid
personal injury or damage to tool.
1. Do not operate any tool when tired or under the influence of drugs,
alcohol or medications.
2. Avoid wearing clothes or jewelry that can become entangled with
the moving parts of a tool. Keep long hair covered or bound.
3. Do not overreach when operating a tool. Proper footing and
balance enables better control in unexpected situations.
4. Keep your fingers away from the trigger/switch while carrying the
tool, attaching an air hose or an accessory. Lock the trigger/switch
safety if available.
5. Avoid unintentional starts. Be sure that the regulator/throttle switch
is in the neutral or OFF position when not in use and before
connecting it to any air source.
6. Never point the air stream or tool at any point of your body, other
people or animals. Debris and dust ejected at high speed can
cause an injury.
7. Serious injury or death may occur from inhaling compressed air. The air
stream may contain carbon monoxide, toxic vapors or solid particles.
Never inhale compressed air directly from the pump or air tool.
SPECIFIC SAFETY PRECAUTIONS
WARNING! DO NOT let comfort or familiarity with product (gained
from repeated use) replace strict adherence to the tool safety
rules. If you use this tool unsafely or incorrectly, you can suffer
serious personal injury.
1. Use the correct tool for the job. This tool was designed for a
specific function. Do not modify or alter this tool or use it for an
unintended purpose.
2. Do not use the tool if any parts are damage broken or misplaced.
Repair or replace the parts.
V1.0 3/8 in. Air Ratchet 8849507
Visit www.princessauto.com for more information 5
3. Never hold the drive, socket, drive extension or accessories during
impacting. Doing so increases the risk of cuts, burns or vibration injuries.
4. Hold the tool correctly; be ready to counteract normal or sudden
movements and have both hands available.
5. The tool is not insulated against contact with live electrical conduits
or sources.
6. Do not over-tighten nuts. They could shatter and cause damage to
the tool or workpiece or cause serious injury. Use a torque wrench
to torque the nut after using the air ratchet.
AIR TOOL PRECAUTIONS
1. Use only clean and dry compressed air as a power source.
Contaminated or moist air will gradually damage the tool.
2. Install an in-line shutoff valve or regulator to allow immediate control
over the air supply in an emergency, even if a hose is ruptured.
3. Discontinue tool use if it does not work properly or air is leaking.
Tag or mark the tool as ‘defective’ or ‘out of service’ until repaired.
4. Check the manufacturer’s maximum pressure rating for air tools
and accessories. Compressor outlet pressure must be regulated to
never exceed the maximum pressure rating of the tool (see
Specifications). Exceeding the maximum PSI rating can create a
bursting hazard, causing injury and property damage.
5. Attach all accessories properly to the tool before connecting the air
supply. A loose accessory may detach or break during operation.
6. Never use oxygen, combustible gas or any other bottled gas as a
power source. Any power source other than an air compressor
could cause an explosion and serious personal injury.
7. Turn OFF the valve and discharge any remaining air pressure after
each use or before adjusting the tool.
8. Do not leave the air tool unattended with its compressed air supply
on. Turn off the compressed air supply and bleed the air tool of any
remaining compressed air before leaving the air tool unattended.
9. Serious injury may occur from loose debris being propelled at high
speeds from the compressed air stream. Always wear OSHA
approved safety glasses to protect the eyes during operation of the
air compressor.
8849507 3/8 in. Air Ratchet V1.0
6 For technical questions call 1-800-665-8685
10. Always turn off the air compressor and drain tank pressure
completely before attempting maintenance or attaching air tools.
Release pressure slowly from the system.
POWER TOOL PRECAUTIONS
1. Do not use any power tool with a malfunctioning power switch or
control. A power tool that fails to respond to the controls is dangerous
and can cause an injury. A qualified technician must repair and verify
the power tool is operating correctly, before it can be used.
2. Disconnect the power source before installing or servicing the tool.
3. Never force the tool. Excessive pressure could break the tool,
resulting in damage to your workpiece or serious personal injury.
Excessive pressure is the cause if your tool runs smoothly under no
load, but roughly under load.
4. Keep hands and fingers away from the work area. Any part of body
contacting the tool’s working parts could cause an injury.
5. Only use accessories that are specifically designed for use with the
tool. Ensure the accessory is tightly installed.
6. Only use an accessory that exceeds the No Load Speed rating
(see Specifications).
7. Before using the tool on a workpiece, test the tool by running it at
the highest no load speed for at least 30 seconds in a safe
position. Stop immediately if there is any abnormal vibration or
wobbling. Check the tool to determine the cause.
8. Never touch the tool accessory or workpiece during or immediately
after use. They may be hot and could inflict a burn injury.
9. Never use a tool with a cracked or worn tool accessory. Change
the tool accessory before using it.
10. Do not place the tool down until the tool’s accessory has stopped
moving. The accessory may catch the surface of work material and
wrench itself free, causing injury to the user or others in the work area.
AIR HOSE PRECAUTIONS
1. Inspect the tool's air hose for cracks, fraying or other faults before
each use. Discontinue use if the air hose is damaged or hissing is
heard from the air hose or connectors. Replace the defective air hose.
V1.0 3/8 in. Air Ratchet 8849507
Visit www.princessauto.com for more information 7
2. Do not allow people, mobile equipment or vehicles to pass over the
unprotected air hose. Position the air hose away from high traffic
areas, in a reinforced conduit or place planks on both sides of the
air hose to create a protective trench.
3. Prevent damage to the air hose by observing the following:
3.1 Never carry the tool by the air hose.
3.2 Keep the air hose behind the tool and out of the tool's work
path.
3.3 Keep the air hose away from heat, oil, sharp edges or moving
parts.
3.4 Do not wrap the air hose around the tool as sharp edges may
pierce or crack the air hose. Gently coil the hose and either
hang on a hook or fasten with a device to keep hose together
when storing.
4. A damaged or disconnected air hose under pressure may whip
around and inflict personal injury or damage the work area. Secure
the compressor's air hose to a fixed or permanent structure with
clamps or cable ties.
VIBRATION PRECAUTIONS
1. This tool vibrates during use. Repeated or long-term exposure to
vibration may cause temporary or permanent physical injury. Take
frequent breaks when using the tool.
2. If you feel any medical symptoms related to vibrations (such as
tingling, numbness, and white or blue fingers), seek medical
attention as soon as possible.
3. Wear suitable gloves to reduce the effects of vibration.
4. DO NOT use this tool before consulting a physician if one of the
following applies:
a. Pregnant
b. Impaired blood circulation to
the hands
c. Past hand injuries
d. Nervous system disorders
e. Diabetes
f. Raynaud's Disease
8849507 3/8 in. Air Ratchet V1.0
8 For technical questions call 1-800-665-8685
UNPACKING
WARNING! Do not operate the tool if any part is missing. Replace
the missing part before operating. Failure to do so could result in
a malfunction and personal injury.
Remove the parts and accessories from the packaging and inspect for
damage. Make sure that all items in the contents are included.
Contents: • Air ratchet
IDENTIFICATION KEY
A Forward/Reverse
Switch
B Square Drive Anvil
C Air Ratchet
D Trigger Lever
E Air Regulator
F Air Inlet
ASSEMBLY & INSTALLATION
Letter references in parenthesis (A) refer to the included Identification Key.
INSTALL AIR CONNECTOR
Prepare a standard 1/4 in. NPT male air connector (sold separately) for
use with your tool.
1. Wrap the external threads of the male connector with sealant tape.
1.1 Wrap tape in a clockwise direction so it will not unravel.
1.2 Do not tape all the threads. Leave several leading threads
unwrapped for easier alignment.
2. Screw the connector into the tool's air inlet (F) and tighten with a
wrench until snug.
3. Run the compressor at a low volume and check the connection for
air leaks. Do not use the tool until all air leaks are repaired or the
faulty component is replaced.
IMPORTANT! Vibration may cause failure if a quick coupler is
connected directly to the air tool. To overcome this, connect a leader
hose to the tool. A quick coupler may then be used to connect the
leader hose to the air line hose.
V1.0 3/8 in. Air Ratchet 8849507
Visit www.princessauto.com for more information 9
SOCKET INSTALLATION
WARNING! The torque of the air ratchet is 25 to 75 ft-lb. Make sure
that the nut or bolt you are using the tool to tighten can withstand
the rated torque and is rated for 450 RPM or greater. If available,
check the recommended torque specifications for the nut.
1. Turn off the air compressor and disconnect the air hose when
changing sockets.
2. Select the appropriately sized 3/8 in. drive impact socket for the
job. Only use impact sockets which are specifically designed for
use with an air ratchet. Do not use worn or damaged sockets.
3. Push and snap the socket (not included) onto the anvil (B).
4. Attach the air hose and turn the air compressor on.
OPERATION
Change the anvil rotation direction with the Forward/Reverse Switch (A)
to either loosen or tighten the nut or bolt.
1. Connect the air ratchet to the air hose.
2. Place the socket over the fastener, grip the air ratchet firmly and gently
squeeze the trigger. Adjust the power with the air regulator (E).
2.1 If the tool stalls while tightening, do not raise the output
pressure of the air compressor above 90 PSI. Pressure above
90 PSI will strip the workpiece and damage the tool,
potentially causing tool failure and serious injury. Use other
appropriate methods and tools to tighten the nut.
3. This tool will stop operation/rotation a few seconds after the trigger
is released.
4. When the fastener is tightened or loosened, release the trigger and
remove the tool and socket.
5. Use a mechanical torque wrench to check the fastener torque after
tightening.
6. When finished with the tool, turn off the air compressor, discharge
any residual air remaining in the tool and disconnect the air hose.
Put the air ratchet away in a safe storage area.
8849507 3/8 in. Air Ratchet V1.0
10 For technical questions call 1-800-665-8685
CARE & MAINTENANCE
1. Maintain the tool with care. A tool in good condition is efficient,
easier to control and will have fewer problems.
2. Inspect the tool fittings, alignment, hoses and power supply cord
periodically. Have damaged or worn components repaired or
replaced by an authorized technician. Only use identical
replacement parts when servicing.
3. Follow instructions for lubricating and changing accessories.
4. Only use accessories intended for use with this tool.
5. Keep the tool clean, dry and free from oil/grease at all times.
6. Maintain the tool’s labels and name plates. These carry important
information. If unreadable or missing, contact Princess Auto Ltd. for
replacements.
WARNING! Only qualified service personnel should repair the
tool. An improperly repaired tool may present a hazard to the
user and/or others.
AIR TOOL LUBRICATION
NOTICE! Only use air tool oil to lubricate the tool. Other
lubricants are not suitable and will damage the tool or cause a
malfunction during use.
NOTICE! Never use a penetrating oil to lubricate an air tool.
Penetrating oil acts as a solvent that will dissolve the tool’s
grease packing and may damage the o-rings, causing the tool to
seize or malfunction.
1. All air tools have an internal coating of grease to prevent corrosion
during shipping and storage. Remove this grease by adding a
generous amount of air tool oil in the air inlet and then run the tool
under no load until the exhaust is clear.
2. Manually add a drop or two of air tool oil into the tool’s male
connector before each use and after every hour of continuous use.
The tool will not work properly without lubrication and parts will
wear prematurely.
3. Avoid adding too much air tool oil as this can cause premature
power loss and eventual tool failure. A qualified technician will need
to take the tool apart and clean out the excess oil.
V1.0 3/8 in. Air Ratchet 8849507
Visit www.princessauto.com for more information 11
4. Apply a generous amount of air tool oil to the tool before storing it
for an extended period of time (overnight, weekend, etc.). Run the
tool for approximately 30 seconds to ensure the oil is evenly
distributed throughout the tool. Store it in a clean and dry location.
DISPOSAL
Recycle a tool damaged beyond repair at the appropriate facility.
Contact your local municipality for a list of disposal facilities or by-laws
for electronic devices, batteries, oil or other toxic liquids.
IMPORTANT! DO NOT pollute the environment by allowing
uncontrolled discharge of waste oil.
TROUBLESHOOTING
Visit a Princess Auto Ltd. location for a solution if the tool does not
function properly or parts are missing. If unable to do so, have a
qualified technician service the tool.
PROBLEM(S) POSSIBLE CAUSE(S) SUGGESTED SOLUTION(S)
Tool runs at
normal speed,
but loses power
under load.
Motor parts worn. 1. Have a qualified technician
service the tool.
2. Replace tool or parts.
Tool runs slowly.
Air flows slightly
from exhaust.
Motor parts jammed with
dirt particles.
OR
Airflow blocked by dirt.
1. Check air inlet filter for
blockage.
2. Pour air tool lubricating oil
into air inlet as per lubrication
instructions for clearing
shipping grease.
3. Operate tool in short bursts
to clear debris.
4. If tool still jammed, clean tool
and lubricate per lubrication
instructions.
Tool runs slowly.
Air flows slightly
from exhaust.
1. Air regulator in closed
position.
2. Damage or excessive
wearing of internal
parts.
1. Open the air regulator to
desired airflow.
2a. Have a qualified technician
service the tool.
2b. Replace tool or parts.
8849507 3/8 in. Air Ratchet V1.0
12 For technical questions call 1-800-665-8685
PROBLEM(S) POSSIBLE CAUSE(S) SUGGESTED SOLUTION(S)
Tool will not shut
off.
1. Throttle valve o-ring
dislodged from inlet
valve seat.
2. Trigger mechanism
jammed or dirty.
1. Replace throttle valve
o-rings.
2. Clean trigger mechanism
and lubricate.
Loss of power or
erratic
performance.
1. Excessive drain on the
air hose. Incorrect size
or type of hose
connectors.
2. Moisture or restriction
in the air hose/tank
3. Air compressor has
insufficient flow.
1. Check the air hose and
confirm the hose fitting is
correct for the inlet bushing.
2. Depressurize system and
drain tank and air hose of
water.
3. Ensure tool is connected to
a compressor with a rate
flow that matches the tool.
V1.0 3/8 in. Air Ratchet 8849507
Visit www.princessauto.com for more information 13
PARTS BREAKDOWN
PARTS LIST
# DESCRIPTION QTY
1
Housing Assembly
1
1.1 Housing
1
1.2 Bushing 1
2 Reverse Switch
1
3 O-Ring
1
4 Spring
1
5 Valve Stem
1
6 O-Ring
1
7 O-Ring
1
8 Trigger Pin
1
9 Muffler Cover
1
10 Air Inlet
1
11 Handle Cover
1
12 Throttle Lever
1
13 Pin
1
14 Gasket
1
15 Cylinder Assembly
1
15.1 Bearing
1
15.2 Rear Plate
1
15.3
Rotor
1
15.4 Rotor Blade
6
15.5
Cylinder
1
15.6 Pin
1
# DESCRIPTION QTY
15.7 Front Plate
1
8849507 3/8 in. Air Ratchet V1.0
14 For technical questions call 1-800-665-8685
15.8 Pin
1
15.9 Bearing
1
16 Washer
1
17 Hammer Cage Assembly
1
1 7. 1 Hammer Cage
1
1 7. 2 Cam Seat
1
1 7. 3 Steel Ball
1
1 7. 4 Drive Cam
1
1 7. 5
Spring
1
1 7. 6 Hammer Pin
2
1 7. 7 Anvil
1
1 7. 8 Washer
1
1 7. 9 Retainer Ring
1
18 Bushing
1
19 Front Cover
1
20 Screw
1
21 Retainer Ring
1
22 Bushing
1
23 Crankshaft
1
24 Drive Bushing
1
25 Ratchet Housing
1
26 Ratchet Yoke
1
27 3/8 in. Ratchet Anvil
Assembly 1
2 7. 1 Reverse Switch
1
2 7. 2 Washer
1
2 7. 3 Spring
1
2 7. 4 Pin
1
2 7. 5 Ratchet Pawl
1
2 7. 6 Sleeve
1
2 7. 7 Spring
1
2 7. 8 3/8 in. Ratchet Anvil
Assembly 1
27.8.1
3/8 in. Ratchet Anvil
1
27.8.2
Steel Ball
1
27.8.3
Spring
1
2 7. 9
Pin
1
28 Spring
2
29 Steel Ball
2
30 Washer
1
31 Retainer Ring
1
V1.0 3/8 in. Air Ratchet 8849507
Visit www.princessauto.com for more information 15
8849507 3/8 in. Air Ratchet V1.0
16 For technical questions call 1-800-665-8685
V1,0 8849507
Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil. Conservez ce
manuel afin de pouvoir le consulter plus tard.
CLIQUET PNEUMATIQUE
DE 3/8 PO
8849507 Cliquet pneumatique de 3/8 po V1,0
2 En cas de questions techniques, appelez le 1-800-665-8685
SPÉCIFICATIONS
Entrée d’air 1/4 po
Format de prise carrée 3/8 po
Plage de pression 70 à 90 lb/po carré
Consommation d'air 4,5 pi cubes/min
Débit à pleine charge 18 pi cubes/min
Couple max. 75 pi-lb
Plage de couple 25 à 75 lb/po carré
Vitesse nominale 450 tr/min
Diamètre min. de tuyau 3/8 po
Matériau Boîtier en aluminium coulé sous pression
DÉFINITIONS DE DANGER
Veuillez-vous familiariser avec les avis de danger qui sont présentés dans
ce manuel. Un avis est une alerte indiquant qu'il existe un risque de
dommage à la propriété, de blessure ou de décès si on ne respecte pas
certaines instructions.
DANGER ! Cet avis indique un risque immédiat et particulier qui
entraînera des blessures corporelles graves ou
même la mort si on omet de prendre les précautions
nécessaires.
AVERTISSEMENT ! Cet avis indique un risque particulier ou une pratique
non sécuritaire qui pourrait entraîner des blessures
corporelles graves ou même la mort si on omet de
prendre les précautions nécessaires.
ATTENTION ! Cet avis indique une situation possiblement
dangereuse qui peut entraîner des blessures
mineures ou modérées si on ne procède pas de la
façon recommandée.
AVIS ! Cet avis indique un risque particulier ou une pratique
non sécuritaire qui entraînera des dommages au
niveau de l'équipement ou des biens, mais non des
blessures corporelles.
V1,0 Cliquet pneumatique de 3/8 po 8849507
Visitez www.princessauto.com pour plus d'informations 3
INTRODUCTION
La clé à cliquet pneumatique de 3/8 po peut desserrer ou serrer des
écrous et des boulons avec une force de 25 à 75 pi-lb. L’entraînement
sans réaction amortit la force d’impact afin de réduire la fatigue et les
contraintes au poignet de l’utilisateur.
SÉCURITÉ
AVERTISSEMENT ! Veuillez lire et comprendre toutes les
instructions avant d'utiliser cet outil. L'utilisateur doit respecter
les précautions de base lorsqu'il utilise cet outil afin de réduire
le risque de blessure ou de dommage à l'équipement.
Conservez ce manuel qui contient les avertissements de sécurité, les
précautions, les instructions de fonctionnement ou d'inspection et
d'entretien.
AIRE DE TRAVAIL
1. Travaillez dans un environnement de travail sécuritaire. Gardez
votre aire de travail propre, bien éclairée et exempte de toute
distraction. Placez les lampes de façon à ne pas travailler dans
l’ombre.
2. Assurez-vous que les personnes qui ne portent pas l'équipement
de sécurité approprié ne se trouvent pas à proximité de l'aire de
travail.
3. Rangez les outils correctement dans un lieu sécurisé et sec.
Gardez les outils hors de la portée des enfants.
SÉCURITÉ PERSONNELLE
AVERTISSEMENT ! Portez de l'équipement de protection
personnelle homologué par l'Association canadienne de
normalisation (CSA) ou l'American National Standards Institute
(ANSI).
ÉQUIPEMENT DE PROTECTION PERSONNELLE
1. Portez toujours des lunettes antiprojections qui offrent une
protection frontale et latérale pour les yeux. L'équipement de
protection des yeux devrait être conforme à la norme CSA Z94.3-
07 ou ANSI Z87.1 fonction du type de travail effectué.
8849507 Cliquet pneumatique de 3/8 po V1,0
4 En cas de questions techniques, appelez le 1-800-665-8685
2. L’outil peut être à haute pression. Portez des lunettes de sécurité et
des gants pour vous protéger au cours de l'opération. Gardez les
mains à l'écart des parties de caoutchouc exposées du tuyau.
3. Portez un écran facial panoramique de type approprié avec les
lunettes de sécurité puisque cette tâche peut créer des copeaux,
des matières abrasives ou des particules.
4. Portez des vêtements de protection conçus pour l'environnement
de travail et pour l'outil.
5. Portez un masque antipoussières ou un appareil respiratoire
nominal approprié.
6. Cet outil peut causer des dommages à l’ouïe. Portez une protection
d’oreille afin d’éliminer ou de réduire le bruit. Si c’est possible,
ajoutez un dispositif au niveau de l’échappement de l’outil
pneumatique pour assourdir le bruit.
PRÉCAUTIONS PERSONNELLES
Gardez le contrôle de l'outil, de vos mouvements et de l'environnement
de travail pour éviter les blessures ou le bris de l'outil.
1. N'utilisez pas l'outil si vous êtes fatigué ou sous l'effet de drogues,
d'alcool ou de médicaments.
2. Évitez de porter des vêtements ou des bijoux pouvant se prendre dans
les pièces mobiles d'un outil. Gardez les cheveux longs recouverts ou
attachés.
3. N'utilisez pas l'outil si vous devez étirer les bras pour vous en
servir. Une stabilité et un équilibre appropriés sont nécessaires afin
d'avoir un meilleur contrôle en cas de situations inattendues.
4. Gardez vos doigts à bonne distance de la gâchette/commutateur lors
du transport de l’outil ou du branchement d’un tuyau à air ou d’un
accessoire. Engagez le verrou de gâchette/interrupteur, le cas
échéant.
5. Évitez les mises en marche involontaires. Assurez-vous que le
régulateur/commutateur est en position neutre ou OFF (arrêt) lorsque
l’outil n’est pas utilisé et avant de le brancher à une source d’air.
6. Ne dirigez jamais le jet d’air ou les outils vers votre corps, d’autres
individus ou des animaux. Les débris et la poussière projetés à
grande vitesse peuvent causer des blessures.
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
PROPOINT 8849507 Le manuel du propriétaire
- Catégorie
- Outils électroportatifs
- Taper
- Le manuel du propriétaire
dans d''autres langues
- English: PROPOINT 8849507 Owner's manual
Documents connexes
Autres documents
-
Power Fist 8843476 Le manuel du propriétaire
-
-
-
Powerfist 8844045 Le manuel du propriétaire
-
-
-
-
-
-