Power Fist 8844078 Le manuel du propriétaire

Marque: Power Fist

Modèle: 8844078

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

V1.0 8844078

Please read and understand all instructions before use. Retain this manual for

future reference.

8844078 3/4 in. Impact Wrench V1.0

2 For technical questions call 1-800-665-8685

SPECIFICATIONS

Air Inlet 1/4 in.

Square Drive Size 3/4 in.

Working Pressure 90 PSI

Average CFM @ 15 Second Run Time 8.25 CFM

CFM @ Full Load 7.5 CFM

Max. Torque 500 ft-lb

Speed Rating 4,500 RPM

Min. Hose Size 3/8 in.

Material Die-cast Aluminum Housing

HAZARD DEFINITIONS

Please familiarize yourself with the hazard notices found in this manual. A

notice is an alert that there is a possibility of property damage, injury or

death if certain instructions are not followed.

DANGER! This notice indicates an immediate and specific hazard that

will result in severe personal injury or death if the proper

precautions are not taken.

WARNING! This notice indicates a specific hazard or unsafe practice that

could result in severe personal injury or death if the proper

precautions are not taken.

CAUTION! This notice indicates a potentially hazardous situation that

may result in minor or moderate injury if proper practices are

not taken.

NOTICE! This notice indicates that a specific hazard or unsafe practice

will result in equipment or property damage, but not personal

injury.

V1.0 3/4 in. Impact Wrench 8844078

Visit www.princessauto.com for more information 3

INTRODUCTION

The 3/4 in. Impact Wrench can loosen or tighten nuts and bolts with 500 ft-lb of

power. Power is controlled by the built-in-air regulator at the handle’s base.

SAFETY

WARNING! Read and understand all instructions before using this tool. The

operator must follow basic precautions to reduce the risk of personal injury

and/or damage to the equipment.

Keep this manual for safety warnings, precautions, operating or inspection

and maintenance instructions.

WORK AREA

1. Operate in a safe work environment. Keep your work area clean, well-lit

and free of distractions. Place lights so you are not working in a shadow.

2. Keep anyone not wearing the appropriate safety equipment away from

the work area.

3. Store unused tools properly in a safe and dry location to prevent rust

or damage. Lock tools away and keep out of the reach of children.

PERSONAL SAFETY

WARNING! Wear personal protective equipment approved by the Canadian

Standards Association (CSA) or American National Standards Institute (ANSI).

PERSONAL PROTECTIVE EQUIPMENT

1. Always wear impact safety goggles that provide front and side protection

for the eyes. Eye protection equipment should comply with CSA Z94.3-07

or ANSI Z87.1 standards based on the type of work performed.

2. The tool may contain high pressure. Use safety glasses and gloves for

protection during operation. Keep hands clear of the exposed rubber

portions of the hose.

3. Wear the appropriate type of full-face shield in addition to safety

googles, as the work can create chips, abrasive or particulate matter.

4. Wear protective clothing designed for the work environment and tool.

5. Wear the appropriate rated dust mask or respirator.

6. This tool can cause hearing damage. Wear ear protection gear to

eliminate or reduce the noise. If possible add a muffling device to the

air tool’s exhaust.

8844078 3/4 in. Impact Wrench V1.0

4 For technical questions call 1-800-665-8685

PERSONAL PRECAUTIONS

Control the tool, personal movement and the work environment to avoid

personal injury or damage to tool.

1. Do not operate any tool when tired or under the influence of drugs,

alcohol or medications.

2. Avoid wearing clothes or jewelry that can become entangled with the

moving parts of a tool. Keep long hair covered or bound.

3. Do not overreach when operating a tool. Proper footing and balance

enables better control in unexpected situations.

4. Securely hold this tool using both hands. Using a tool with only one

hand can result in loss of control.

5. Keep your fingers away from the trigger/switch while carrying the tool,

attaching an air hose or an accessory. Lock the trigger/switch safety if

available.

6. Avoid unintentional starts. Be sure that the regulator/throttle switch is

in the neutral or OFF position when not in use and before connecting it

to any air source.

7. Never point the air stream or tool at any point of your body, other

people or animals. Debris and dust ejected at high speed can cause an

injury.

8. Serious injury or death may occur from inhaling compressed air. The air

stream may contain carbon monoxide, toxic vapors or solid particles.

Never inhale compressed air directly from the pump or air tool.

SPECIFIC SAFETY PRECAUTIONS

WARNING! DO NOT let comfort or familiarity with product (gained from

repeated use) replace strict adherence to the tool safety rules. If you use

this tool unsafely or incorrectly, you can suffer serious personal injury.

1. Use the correct tool for the job. This tool was designed for a specific function.

Do not modify or alter this tool or use it for an unintended purpose.

2. Do not use the tool if any parts are damage broken or misplaced. Repair

or replace the parts.

3. Never hold the drive, socket, drive extension or accessories

during impacting. Doing so increases the risk of cuts, burns or

vibration injuries.

4. Hold the tool correctly; be ready to counteract normal or sudden

movements and have both hands available.

V1.0 3/4 in. Impact Wrench 8844078

Visit www.princessauto.com for more information 5

5. Do not use in confined spaces and beware of crushing your hands

between the tool and workpiece, especially when unscrewing.

6. The tool is not insulated against contact with live electrical conduits or

sources.

7. Do not over-tighten nuts. They could shatter and cause damage to the

tool or workpiece or cause serious injury. Use a torque wrench to

torque the nut after using the impact wrench.

8. This impact wrench should only be used with impact sockets and

extensions. Use of other accessories can cause them to break, which

could damage the unit or cause injury.

AIR TOOL PRECAUTIONS

1. Use only clean and dry compressed air as a power source.

Contaminated or moist air will gradually damage the tool.

2. Install an in-line shutoff valve or regulator to allow immediate control

over the air supply in an emergency, even if a hose is ruptured.

3. Discontinue tool use if it does not work properly or air is leaking. Tag

or mark the tool as ‘defective’ or ‘out of service’ until repaired.

4. Check the manufacturer’s maximum pressure rating for air tools and

accessories. Compressor outlet pressure must be regulated to never

exceed the maximum pressure rating of the tool (see Specifications).

Exceeding the maximum PSI rating can create a bursting hazard,

causing injury and property damage.

5. Attach all accessories properly to the tool before connecting the air

supply. A loose accessory may detach or break during operation.

6. Never use oxygen, combustible gas or any other bottled gas as a

power source. Any power source other than an air compressor could

cause an explosion and serious personal injury.

7. Turn OFF the valve and discharge any remaining air pressure after each

use or before adjusting the tool.

8. Do not leave the air tool unattended with its compressed air supply on.

Turn off the compressed air supply and bleed the air tool of any

remaining compressed air before leaving the air tool unattended.

9. Serious injury may occur from loose debris being propelled at high

speeds from the compressed air stream. Always wear OSHA approved

safety glasses to protect the eyes during operation of the air

compressor.

8844078 3/4 in. Impact Wrench V1.0

6 For technical questions call 1-800-665-8685

10. Always turn off the air compressor and drain tank pressure completely

before attempting maintenance or attaching air tools. Release pressure

slowly from the system.

11. Serious injury or death may occur from inhaling compressed air. The air

stream may contain carbon monoxide, toxic vapors or solid particles.

Never inhale compressed air directly from the pump or air tool.

POWER TOOL PRECAUTIONS

1. Do not use any power tool with a malfunctioning power switch or

control. A power tool that fails to respond to the controls is dangerous

and can cause an injury. A qualified technician must repair and verify

the power tool is operating correctly, before it can be used.

2. Disconnect the power source before installing or servicing the tool.

3. Never force the tool. Excessive pressure could break the tool, resulting

in damage to your workpiece or serious personal injury. Excessive

pressure is the cause if your tool runs smoothly under no load, but

roughly under load.

4. Keep hands and fingers away from the work area. Any part of body

contacting the tool’s working parts could cause an injury.

5. Only use accessories that are specifically designed for use with the

tool. Ensure the accessory is tightly installed.

6. Only use an accessory that exceeds the No Load Speed rating (see

Specifications).

7. Before using the tool on a workpiece, test the tool by running it at the

highest no load speed for at least 30 seconds in a safe position. Stop

immediately if there is any abnormal vibration or wobbling. Check the

tool to determine the cause.

8. Never touch the tool accessory or workpiece during or immediately after

use. They may be hot and could inflict a burn injury.

9. Never use a tool with a cracked or worn tool accessory. Change the

tool accessory before using it.

10. Do not place the tool down until the tool’s accessory has stopped

moving. The accessory may catch the surface of work material and

wrench itself free, causing injury to the user or others in the work area.

V1.0 3/4 in. Impact Wrench 8844078

Visit www.princessauto.com for more information 7

AIR HOSE PRECAUTIONS

1. Inspect the tool's air hose for cracks, fraying or other faults before

each use. Discontinue use if the air hose is damaged or hissing is heard

from the air hose or connectors. Replace the defective air hose.

2. Do not allow people, mobile equipment or vehicles to pass over the

unprotected air hose. Position the air hose away from high traffic

areas, in a reinforced conduit or place planks on both sides of the air

hose to create a protective trench.

3. Prevent damage to the air hose by observing the following:

a. Never carry the tool by the air hose.

b. Keep the air hose behind the tool and out of the tool's work path.

c. Keep the air hose away from heat, oil, sharp edges or moving parts.

d. Do not wrap the air hose around the tool as sharp edges may pierce

or crack the air hose. Gently coil the hose and either hang on a hook

or fasten with a device to keep hose together when storing.

4. A damaged or disconnected air hose under pressure may whip around and

inflict personal injury or damage the work area. Secure the compressor's

air hose to a fixed or permanent structure with clamps or cable ties.

COMPRESSOR/TANK PRECAUTIONS

DANGER! Do not use an air tank beyond its expiration date. A tank rupture

or explosion may kill or cause a serious injury to yourself or a bystander.

Disable and discard the air tank according to the your municipality by-laws.

1. Never drill into, weld, patch or modify the air tank. Immediately replace the

tank or compressor if an air leak develops. The leak may lead to a rupture.

2. Never make adjustments to the components that control tank pressure.

Serious injury or death may occur if modifications are made to the

pressure switch, safety relief valve or other components that control

the tank pressure.

3. Check operation of the pressure relief valve on a regular basis and

never operate without a factory approved pressure relief valve. Do not

make alterations to the factory operating pressure settings.

VIBRATION PRECAUTIONS

1. This tool vibrates during use. Repeated or long-term exposure to

vibration may cause temporary or permanent physical injury. Take

frequent breaks when using the tool.

8844078 3/4 in. Impact Wrench V1.0

8 For technical questions call 1-800-665-8685

2. If you feel any medical symptoms related to vibrations (such as

tingling, numbness, and white or blue fingers), seek medical attention

as soon as possible.

3. Wear suitable gloves to reduce the effects of vibration.

4. DO NOT use this tool before consulting a physician if one of the

following applies:

a. Pregnant

b. Impaired blood circulation to the

hands

c. Past hand injuries

d. Nervous system disorders

e. Diabetes

f. Raynaud's Disease

UNPACKING

WARNING! Do not operate the tool if any part is missing. Replace the

missing part before operating. Failure to do so could result in a malfunction

and personal injury.

Remove the parts and accessories from the packaging and inspect for damage.

Make sure that all items in the contents are included.

Contents: • Impact Wrench • Male Plug • Hex Key

IDENTIFICATION KEY

A Square Drive Anvil

B Valve Stem

C Trigger

D Air Flow Regulator

E Air Inlet

ASSEMBLY & INSTALLATION

Letter references in parenthesis (A) refer to the included Identification Key.

INSTALL AIR CONNECTOR

Prepare a standard 1/4 in. NPT male air connector (sold separately) for use

with your tool.

1. Wrap the external threads of the male connector with sealant tape.

a. Wrap tape in a clockwise direction so it will not unravel.

V1.0 3/4 in. Impact Wrench 8844078

Visit www.princessauto.com for more information 9

b. Do not tape all the threads. Leave several leading threads

unwrapped for easier alignment.

2. Screw the connector into the tool's air inlet (E) and tighten with a

wrench until snug.

3. Run the compressor at a low volume and check the connection for air

leaks. Do not use the tool until all air leaks are repaired or the faulty

component is replaced.

IMPORTANT! Vibration may cause failure if a quick coupler is connected directly

to the air tool. To overcome this, connect a leader hose to the tool. A quick

coupler may then be used to connect the leader hose to the air line hose.

SOCKET INSTALLATION

WARNING! The torque of the impact wrench is 500 ft-lb. Make sure that the

nut or bolt you are using the tool to tighten can withstand the rated torque

and is rated for 4,500 RPM or greater. If available, check the recommended

torque specifications for the nut.

1. Turn off the air compressor and disconnect the air hose when changing

sockets.

2. Select the appropriately sized 3/4 in. drive impact socket for the job.

Only use impact sockets which are specifically designed for use with

an impact wrench. Do not use worn or damaged sockets.

3. Push and snap the socket (not included) onto the anvil (A).

4. Attach the air hose and turn the air compressor on.

OPERATION

WARNING! This tool generates considerable torque when in use. Always

hold the tool with both hands when using and brace yourself to resist the

torque which will be delivered to the workpiece.

Lubricate the rotor gears at the beginning of each day of use. See the

Lubricating Rotor Gears section.

1. Tighten the nut as far as you can by hand before using the impact

wrench.

2. Connect the impact wrench to the air hose.

3. Power is increased or decreased by adjusting the air flow with the

regulator (D) at the handle’s base.

8844078 3/4 in. Impact Wrench V1.0

10 For technical questions call 1-800-665-8685

a. Push the air flow regulator in to allow adjustments. The knob is

numbered 1 to 4, with 1 being the least powerful and 4 as the

most powerful.

b. Rotate the knob to align the number with the triangle inset in the

handle.

c. Fine tune the power by rotating the dial between two numbers.

4. Push the valve stem (B) out for forward (clockwise) and push the stem

in for reverse (counterclockwise).

a. Wait until the tool’s anvil has stopped rotating before switching to

the opposite direction.

5. Place the socket over the fastener, grip the impact wrench firmly with

both hands and gently squeeze the trigger. The impact wrench will

activate when the trigger is squeezed.

a. If the tool stalls while tightening, do not raise the output pressure

of the air compressor above 90 PSI. Pressure above 90 PSI will

strip the workpiece and damage the tool, potentially causing tool

failure and serious injury. Use other appropriate methods and

tools to tighten the nut.

6. This tool will stop operation/rotation a few seconds after the trigger is

released.

7. When the fastener is tightened, release the trigger and remove the tool

and socket.

8. Use a mechanical torque wrench to check the fastener torque.

9. When finished with the tool, turn off the air compressor, disconnect

the air hose and discharge any residual air remaining in the tool. Put

the impact wrench away in a safe storage area.

CARE & MAINTENANCE

1. Maintain the tool with care. A tool in good condition is efficient, easier

to control and will have fewer problems.

2. Inspect the tool fittings, alignment, hoses and power supply cord

periodically. Have damaged or worn components repaired or replaced

by an authorized technician. Only use identical replacement parts

when servicing.

3. Follow instructions for lubricating and changing accessories.

4. Only use accessories intended for use with this tool.

V1.0 3/4 in. Impact Wrench 8844078

Visit www.princessauto.com for more information 11

5. Keep the tool clean, dry and free from oil/grease at all times.

6. Maintain the tool’s labels and name plates. These carry important

information. If unreadable or missing, contact Princess Auto Ltd. for

replacements.

WARNING! Only qualified service personnel should repair the tool. An

improperly repaired tool may present a hazard to the user and/or others.

AIR TOOL LUBRICATION

NOTICE! Only use air tool oil to lubricate the tool. Other lubricants are not

suitable and will damage the tool or cause a malfunction during use.

NOTICE! Never use a penetrating oil to lubricate an air tool. Penetrating oil

acts as a solvent that will dissolve the tool’s grease packing and may

damage the o-rings, causing the tool to seize or malfunction.

1. All air tools have an internal coating of grease to prevent corrosion

during shipping and storage. Remove this grease by adding a generous

amount of air tool oil in the air inlet and then run the tool under no

load until the exhaust is clear.

2. Manually add a drop or two of air tool oil into the tool’s air inlet before

each use and after every hour of continuous use. The tool will not work

properly without lubrication and parts will wear prematurely.

3. Avoid adding too much air tool oil as this can cause premature power

loss and eventual tool failure. A qualified technician will need to take

the tool apart and clean out the excess oil.

4. Apply a generous amount of air tool oil to the tool before storing it for

an extended period of time (overnight, weekend, etc.). Run the tool for

approximately 30 seconds to ensure the oil is evenly distributed

throughout the tool. Store it in a clean and dry location.

LUBRICATING ROTOR GEARS AND IMPACT MECHANISM

Lubricate the rotor gears and impact mechanism before using at the

beginning of the day.

1. Remove the hex screw (Fig. 2) to the grease

opening and set aside.

2. Insert the grease gun nozzle into the opening

and squeeze out several drops of grease.

3. Replace the screw and tighten.

4. Run the tool without load for several seconds

to spread the grease.

Fig. 2

8844078 3/4 in. Impact Wrench V1.0

12 For technical questions call 1-800-665-8685

DISPOSAL

Recycle a tool damaged beyond repair at the appropriate facility.

Contact your local municipality for a list of disposal facilities or by-laws for

electronic devices, batteries, oil or other toxic liquids.

IMPORTANT! DO NOT pollute the environment by allowing uncontrolled

discharge of waste oil.

TROUBLESHOOTING

Visit a Princess Auto Ltd. location for a solution if the tool does not function

properly or parts are missing. If unable to do so, have a qualified technician

service the tool.

Problem(s) Possible Cause(s) Suggested Solution(s)

Tool runs at

normal speed, but

loses power under

load.

Motor parts worn.

1. Have a qualified technician

service the tool.

2. Replace tool or parts.

Tool runs slowly.

Air flows slightly

from exhaust.

Motor parts jammed

with dirt particles.

Airflow blocked by

dirt.

1. Check air inlet filter for

blockage.

2. Pour air tool lubricating oil

into air inlet as per

lubrication instructions for

clearing shipping grease.

3. Operate tool in short bursts

to clear debris.

4. If tool still jammed, clean

tool and lubricate per

lubrication instructions.

Tool runs

slowly. Air flows

slightly from

exhaust.

1. Air regulator in

closed position.

Damage or excessive

wearing of internal

parts.

1. Open the air regulator to

desired airflow.

2a. Have a qualified technician

service the tool.

2b. Replace tool or parts.

Tool will not

shut off.

1. Throttle valve o-ring

dislodged from inlet

valve seat.

2. Trigger mechanism

jammed or dirty.

1. Replace throttle valve

o-rings.

2. Clean trigger mechanism and

lubricate.

V1.0 3/4 in. Impact Wrench 8844078

Visit www.princessauto.com for more information 13

Problem(s) Possible Cause(s) Suggested Solution(s)

Loss of power

or erratic

performance.

1. Excessive drain on

the air hose

. Incorrect

size or type of hose

connectors.

2. Moisture or

restriction in the air

hose/tank

3. Air compressor has

insufficient flow.

1. Check the air hose and

confirm the hose fitting is

correct for the inlet

bushing.

2. Depressurize system and

drain tank and air hose of

water.

3. Ensure tool is connected to

a compressor with a rate

flow that matches the tool.

PARTS BREAKDOWN

PARTS LIST

# DESCRIPTION QTY

1 Protecting Rubber 1

2 Oil Seal 1

3 Housing 1

4 Screw 1

5 Anvil Bushing 1

6 Anvil Collar 1

7 O-Ring 1

8 Spacer 1

9 Anvil (3/4 in.) 1

8844078 3/4 in. Impact Wrench V1.0

14 For technical questions call 1-800-665-8685

# DESCRIPTION QTY

10 Hammer Pin 1

11 Hammer Dog 1

12 Drive Cam 1

13 Hammer Cage 1

14 Ball Bearing 1

15 Oil Seal 2

16 O-Ring 1

17 Front End Plate 1

18 Rotor Blade 6

19 Rotor 1

20 Cylinder 1

21 Rear End Plate 1

22 Ball Bearing 1

23 Rear Gasket

24 Rear Cover 1

25 Washer 3

26 Screw 3

27 Protecting Rubber 1

28 Washer 4

29 Screw 4

30 Valve Sleeve 1

31 Reverse Valve 1

32 Screw 1

33 Spring 1

34 Pin 1

35 Screw 2

36 Exhaust Deflector 1

37 Trigger 1

38 Screw 1

39 Pin 1

40 Pin 1

41 Bushing 1

42 Valve Stem 1

43 Ball Valve 1

44 Spring 1

45 Hose Adapter 1

46 Screen 1

47 O-Ring 1

48 Air Regulator 1

V1,0 8844078

Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil.

Conservez ce manuel afin de pouvoir le consulter plus tard.

8844078 Clé à chocs de 3/4 po V1,0

2 En cas de questions techniques, appelez le 1-800-665-8685

SPÉCIFICATIONS

Entrée d’air 1/4 po

Format de prise carrée 3/4 po

Pression de travail 90 lb/po carré

Débit moyen à un temps de

fonctionnement de 15 secondes

8,25 pi cubes/min

Débit à pleine charge 7,5 pi cubes/min

Couple max. 500 pi-lb

Vitesse nominale 4 500 tr/min

Diamètre min. de tuyau 3/8 po

Matériau

Boîtier en aluminium coulé sous

pression

DÉFINITIONS DE DANGER

Veuillez-vous familiariser avec les avis de danger qui sont présentés dans ce

manuel. Un avis est une alerte indiquant qu'il existe un risque de dommage à la

propriété, de blessure ou de décès si on ne respecte pas certaines instructions.

DANGER ! Cet avis indique un risque immédiat et particulier qui

entraînera des blessures corporelles graves ou même la

mort si on omet de prendre les précautions nécessaires.

AVERTISSEMENT ! Cet avis indique un risque particulier ou une pratique non

sécuritaire qui

pourrait entraîner des blessures

corporelles graves ou même la mort si on omet de

prendre les précautions nécessaires.

ATTENTION ! Cet avis indique une situation possiblement dangereuse qui

peut entraîner des blessures mineures ou modérées si on

ne procède pas de la façon recommandée.

AVIS ! Cet avis indique un risque particulier ou une pratique non

sécuritaire qui entraînera des dommages au niveau de

l'équipement ou des biens, mais non des blessures

corporelles.

V1,0 Clé à chocs de 3/4 po 8844078

Visitez www.princessauto.com pour plus d'informations 3

INTRODUCTION

La clé à chocs de 3/4 po peut desserrer ou serrer des écrous et des boulons

avec une force de 500 pi-lb. L’alimentation est commandée au moyen d’un

régulateur pneumatique intégré à la base de la poignée.

SÉCURITÉ

AVERTISSEMENT ! Veuillez lire et comprendre toutes les instructions avant

d'utiliser cet outil. L'utilisateur doit respecter les précautions de base

lorsqu'il utilise cet outil afin de réduire le risque de blessure ou de

dommage à l'équipement.

Conservez ce manuel qui contient les avertissements de sécurité, les

précautions, les instructions de fonctionnement ou d'inspection et d'entretien.

AIRE DE TRAVAIL

1. Travaillez dans un environnement de travail sécuritaire. Gardez votre

aire de travail propre, bien éclairée et exempte de toute distraction.

Placez les lampes de façon à ne pas travailler dans l’ombre.

2. Assurez-vous que les personnes qui ne portent pas l'équipement de

sécurité approprié ne se trouvent pas à proximité de l'aire de travail.

3. Rangez les outils correctement dans un lieu sécurisé et sec. Gardez les

outils hors de la portée des enfants.

SÉCURITÉ PERSONNELLE

AVERTISSEMENT ! Portez de l'équipement de protection personnelle

homologué par l'Association canadienne de normalisation (CSA) ou

l'American National Standards Institute (ANSI).

ÉQUIPEMENT DE PROTECTION PERSONNELLE

1. Portez toujours des lunettes antiprojections qui offrent une protection

frontale et latérale pour les yeux. L'équipement de protection des yeux

devrait être conforme à la norme CSA Z94.3-07 ou ANSI Z87.1 fonction

du type de travail effectué.

2. L’outil peut être à haute pression. Portez des lunettes de sécurité et

des gants pour vous protéger au cours de l'opération. Gardez les mains

à l'écart des parties de caoutchouc exposées du tuyau.

3. Portez un écran facial panoramique de type approprié avec les lunettes

de sécurité puisque cette tâche peut créer des copeaux, des matières

abrasives ou des particules.

8844078 Clé à chocs de 3/4 po V1,0

4 En cas de questions techniques, appelez le 1-800-665-8685

4. Portez des vêtements de protection conçus pour l'environnement de

travail et pour l'outil.

5. Portez un masque antipoussières ou un appareil respiratoire

nominal approprié.

6. Cet outil peut causer des dommages à l’ouïe. Portez une protection

d’oreille afin d’éliminer ou de réduire le bruit. Si c’est possible, ajoutez

un dispositif au niveau de l’échappement de l’outil pneumatique pour

assourdir le bruit.

PRÉCAUTIONS PERSONNELLES

Gardez le contrôle de l'outil, de vos mouvements et de l'environnement de

travail pour éviter les blessures ou le bris de l'outil.

1. N'utilisez pas l'outil si vous êtes fatigué ou sous l'effet de drogues,

d'alcool ou de médicaments.

2. Évitez de porter des vêtements ou des bijoux pouvant se prendre dans les

pièces mobiles d'un outil. Gardez les cheveux longs recouverts ou attachés.

3. N'utilisez pas l'outil si vous devez étirer les bras pour vous en servir.

Une stabilité et un équilibre appropriés sont nécessaires afin d'avoir un

meilleur contrôle en cas de situations inattendues.

4. Tenez cet outil solidement à l’aide des deux mains. Un outil tenu d’une

seule main peut causer une perte de contrôle.

5. Gardez vos doigts à bonne distance de la gâchette/commutateur lors

du transport de l’outil ou du branchement d’un tuyau à air ou d’un

accessoire. Engagez le verrou de gâchette/interrupteur, le cas échéant.

6. Évitez les mises en marche involontaires. Assurez-vous que le

régulateur/commutateur est en position neutre ou OFF (arrêt) lorsque

l’outil n’est pas utilisé et avant de le brancher à une source d’air.

7. Ne dirigez jamais le jet d’air ou les outils vers votre corps, d’autres

individus ou des animaux. Les débris et la poussière projetés à grande

vitesse peuvent causer des blessures.

8. Des blessures graves ou même la mort peuvent survenir en cas

d’inhalation de l’air comprimé. Le jet d’air peut contenir du monoxyde

de carbone, des vapeurs toxiques ou des particules solides. N’inhalez

jamais l’air comprimé provenant directement de la pompe ou d’un outil

pneumatique.

V1,0 Clé à chocs de 3/4 po 8844078

Visitez www.princessauto.com pour plus d'informations 5

CONSIGNES DE SÉCURITÉ SPÉCIFIQUES

AVERTISSEMENT! Ne permettez PAS au confort ou à votre familiarisation

avec l'outil (obtenus après un emploi répété) de se substituer à une

adhésion stricte aux règles de sécurité de l'outil. Si vous utilisez cet outil de

façon dangereuse ou incorrecte, vous pouvez subir des blessures

corporelles graves.

1. Utilisez le bon outil pour la tâche à effectuer. Cet outil a été conçu pour

une utilisation spécifique. Évitez de modifier ou d'altérer cet outil ou de

l'utiliser à une fin autre que celle pour laquelle il a été conçu.

2. N’utilisez pas l’outil si des pièces présentent des dommages ou sont

déplacées. Réparez ou remplacez les pièces.

3. Ne tenez jamais la prise, la douille et la rallonge de la prise ou les accessoires

au moment de frapper. Ce faisant, vous augmenterez les risques de

coupures, de brûlures ou de blessures causées par les vibrations.

4. Tenez l'outil correctement; soyez prêt à contrer tout mouvement

normal ou brusque et assurez-vous que vos deux mains

sont disponibles.

5. N'utilisez pas dans des espaces restreints et faites attention de ne pas

écraser vos mains entre l'outil et la pièce à travailler, en particulier au

moment de la dévisser.

6. Cet outil n'est pas isolé advenant tout contact avec des conduits ou des

sources électriques sous tension.

7. Ne serrez pas trop les écrous. Ils pourraient se briser et endommager l’outil

ou l’ouvrage, ou bien causer une blessure grave. Servez-vous d’une clé

dynamométrique pour serrer l’écrou après avoir utilisé la clé à douilles.

8. Cette clé à chocs ne devrait être utilisée qu’avec des rallonges et des

douilles pour clés à chocs. L’emploi d’autres accessoires pourrait

entraîner leur bris et causer des avaries permanentes à l’appareil et des

blessures graves à l’utilisateur.

PRÉCAUTIONS RELATIVES AUX OUTILS PNEUMATIQUES

1. Utilisez uniquement un air comprimé propre et sec comme source

d’énergie. L’air contaminé ou humide endommagera progressivement

l’outil.

2. Installez une soupape d'arrêt ou un régulateur sur la conduite afin de

permettre une commande immédiate de l'alimentation en air, en cas

d'urgence, même si un tuyau se fend.

8844078 Clé à chocs de 3/4 po V1,0

6 En cas de questions techniques, appelez le 1-800-665-8685

3. Consultez la pression nominale maximale du fabricant en ce qui

concerne les outils pneumatiques et accessoires. La pression de sortie

du compresseur doit être réglée de façon à ne jamais dépasser la

pression nominale maximale de l'outil (consultez Spécifications). Si on

dépasse la pression nominale maximale, il pourrait en résulter un

risque d’explosion capable d’entraîner des blessures et des dommages

aux biens.

4. Arrêtez d’utiliser l’outil s’il ne fonctionne pas correctement ou s’il

présente des fuites d’air. Attachez une étiquette sur l’outil indiquant

qu’il est « défectueux » ou qu’il est « hors service », jusqu’à ce qu’il soit

réparé.

5. Avant de relier l’alimentation en air, fixez correctement tous les

accessoires sur l’outil. Un accessoire mal attaché pourrait se détacher

et se briser durant l’utilisation.

6. N'utilisez jamais d'oxygène, de gaz combustible ou tout autre gaz

embouteillé en tant que source d'énergie. Une source d'énergie autre

qu'un compresseur d'air pourrait causer une explosion entraînant ainsi

des blessures corporelles graves.

7. Fermez la soupape et évacuez toute la pression d’air restante après

chaque utilisation ou avant d’ajuster l’outil.

8. Ne laissez pas l’outil d'air sans surveillance alors que la source d'air

comprimé est en fonction. Fermez la source d'air comprimé et purgez

l’outil d'air de tout air comprimé restant avant de laisser celui-ci sans

surveillance.

9. Des blessures graves peuvent se produire si des débris sont propulsés

à haute vitesse dans le jet d’air du compresseur. Portez toujours des

lunettes de sécurité approuvés OSHA afin de vous protéger les yeux

lorsque vous utilisez le compresseur d’air.

10. Arrêtez toujours le compresseur d’air et évacuez complètement la

pression du réservoir avant de tenter de procéder à l’entretien ou de

fixer des outils pneumatiques. Évacuez doucement la pression du

système.

11. Des blessures graves ou même la mort peuvent survenir en cas

d’inhalation de l’air comprimé. Le jet d’air peut contenir du monoxyde

de carbone, des vapeurs toxiques ou des particules solides. N’inhalez

jamais l’air comprimé provenant directement de la pompe ou d’un outil

pneumatique.

La page charge ...

Power Fist 8844078 Le manuel du propriétaire

Marque: Power Fist

Modèle: 8844078

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Power Fist 8844078 Owner's manual

Power Fist 8844078 Le manuel du propriétaire

Power Fist 8844078 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents