PROPOINT 8843997 Le manuel du propriétaire

Marque: PROPOINT

Modèle: 8843997

Catégorie: Coupe-bordures

Taper: Le manuel du propriétaire

V1.0 8843997

Please read and understand all instructions before use. Retain this manual for future

reference.

AIR IMPACT WRENCH



3/8 IN.

8843997 3/8 in. Air Impact Wrench V1.0

2 For technical questions call 1-800-665-8685

SPECIFICATIONS

Square Drive Size 3/8 in.

Max. Torque 350 ft-lb

Speed Rating 13,000 RPM

Average CFM @ 15 Second Run Time 5.7 CFM

CFM @ Full Load 22 CFM

Pressure Rating 90 PSI

Air Inlet 1/4 in.

Material Composite housing with cushion grip

HAZARD DEFINITIONS

Please familiarize yourself with the hazard notices found in this manual.

A notice is an alert that there is a possibility of property damage, injury

or death if certain instructions are not followed.

DANGER! This notice indicates an immediate and specific hazard that

will result in severe personal injury or death if the proper

precautions are not taken.

WARNING! This notice indicates a specific hazard or unsafe practice

that could result in severe personal injury or death if the

proper precautions are not taken.

CAUTION! This notice indicates a potentially hazardous situation that

may result in minor or moderate injury if proper practices are

not taken.

NOTICE! This notice indicates that a specific hazard or unsafe

practice will result in equipment or property damage, but

not personal injury.

V1.0 3/8 in. Air Impact Wrench 8843997

Visit www.princessauto.com for more information 3

INTRODUCTION

This 3/8 in. Air Impact Wrench has a composite housing with a cushion

grip and maximum torque of 350 ft/lb. The tool has variable torque in

forward and reverse.

SAFETY

WARNING! Read and understand all instructions before using this

tool. The operator must follow basic precautions to reduce the

risk of personal injury and/or damage to the equipment.

Keep this manual for safety warnings, precautions, operating or

inspection and maintenance instructions.

WORK AREA

1. Operate in a safe work environment. Keep your work area clean,

well-lit and free of distractions. Place lights so you are not working

in a shadow.

2. Keep anyone not wearing the appropriate safety equipment away

from the work area.

3. Store tools properly in a safe and dry location. Keep tools out of

the reach of children.

4. Do not install or use in the presence of flammable gases, dust or

liquids.

PERSONAL SAFETY

WARNING! Wear personal protective equipment approved by the

Canadian Standards Association (CSA) or American National

Standards Institute (ANSI).

PERSONAL PROTECTIVE EQUIPMENT

1. Always wear impact safety goggles that provide front and side

protection for the eyes. Eye protection equipment should comply

with CSA Z94.3-07 or ANSI Z87.1 standards based on the type of

work performed.

2. Wear the appropriate type of full-face shield in addition to safety

googles, as the work can create chips, abrasive or particulate matter.

3. Wear gloves that provide protection based on the work materials or

to reduce the effects of tool vibration.

8843997 3/8 in. Air Impact Wrench V1.0

4 For technical questions call 1-800-665-8685

3.1 Do not wear gloves when operating a tool that can snag the

material and pull the hand into the tool.

4. Wear protective clothing designed for the work environment and

tool.

5. Non-skid footwear is recommended to maintain footing and

balance in the work environment.

6. This tool can cause hearing damage. Wear hearing protection gear

with an appropriate Noise Reduction Rating to withstand the

decibel levels.

7. The tool may contain high pressure. Use safety glasses and gloves

for protection during operation. Keep hands clear of the exposed

rubber portions of the hose.

PERSONAL PRECAUTIONS

Control the tool, personal movement and the work environment to avoid

personal injury or damage to the tool.

1. Do not operate any tool when tired or under the influence of drugs,

alcohol or medications.

2. Avoid wearing clothes or jewelry that can become entangled with

the moving parts of a tool. Keep long hair covered or bound.

3. Do not overreach when operating a tool. Proper footing and

balance enables better control in unexpected situations.

4. Keep your fingers away from the trigger/switch while carrying the

tool, attaching an air hose or an accessory. Lock the trigger/switch

safety if available.

5. Avoid unintentional starts. Be sure that the regulator/throttle switch

is in the neutral or OFF position when not in use and before

connecting it to any air source.

6. Never point the air stream or tool at any point of your body, other

people or animals. Debris and dust ejected at high speed can

cause an injury.

7. Serious injury or death may occur from inhaling compressed air. The air

stream may contain carbon monoxide, toxic vapors or solid particles.

Never inhale compressed air directly from the pump or air tool.

8. Support the workpiece or clamp it to a stable platform. Holding the

workpiece by hand or against your body may lead to personal injury.

V1.0 3/8 in. Air Impact Wrench 8843997

Visit www.princessauto.com for more information 5

9. Securely hold this tool using both hands. Using a tool with only one

hand can result in loss of control.

SPECIFIC SAFETY PRECAUTIONS

WARNING! DO NOT let comfort or familiarity with product (gained

from repeated use) replace strict adherence to the tool safety rules.

If you use this tool unsafely or incorrectly, you can suffer serious

personal injury.

1. Use the correct tool for the job. This tool was designed for a

specific function. Do not modify or alter this tool or use it for an

unintended purpose.

2. Do not use the tool if any parts are damaged, broken or misplaced.

Repair or replace the parts.

3. Do not use any power tool with a malfunctioning power switch or

control. A power tool that fails to respond to the controls is

dangerous and can cause an injury. A qualified technician must

repair and verify the power tool is operating correctly before it can

be used.

4. Never use a tool with a cracked or worn tool accessory. Change

the tool accessory before using it.

5. Never operate the tool when the safety guard is removed or

broken. Never clamp or tie the guard into the open position.

6. Do not cover the air vents.

7. Only use accessories that are specifically designed for use with the

tool. Ensure the accessory is tightly installed.

8. Only use an accessory that exceeds the speed rating (see

Specifications).

9. Disconnect the power source before installing or servicing the tool.

10. Remove adjusting keys and wrenches before using the tool. The

tool may eject an attached wrench or a key and cause an injury to

you or a bystander.

11. Before using the tool on a workpiece, test the tool by running it at

the highest speed rating for at least 30 seconds in a safe position.

Stop immediately if there is any abnormal vibration or wobbling.

Check the tool to determine the cause.

8843997 3/8 in. Air Impact Wrench V1.0

6 For technical questions call 1-800-665-8685

12. Never force the tool. Excessive pressure could break the tool,

resulting in damage to your workpiece or serious personal injury.

Excessive pressure is the cause if your tool runs smoothly under no

load, but roughly under load.

13. Keep hands and fingers away from the work area. Any part of the

body contacting the tool’s working parts could result in an injury.

14. Never touch the tool accessory or workpiece during or immediately

after use. They may be hot and could inflict a burn injury.

15. Do not place the tool down until the tool’s accessory has stopped

moving. The accessory may catch the surface of work material and

wrench itself free, causing injury to the user or others in the work area.

16. Never hold the drive, socket, drive extension or accessories during

impacting. Doing so increases the risk of cuts, burns or vibration

injuries.

17. Use a torque bar or forearm brace to absorb reaction torque above

10-Nm to protect against a twist injury.

AIR TOOL PRECAUTIONS

1. Use only clean and dry compressed air as a power source.

Contaminated or moist air will gradually damage the tool.

2. Install an in-line shutoff valve or regulator to allow immediate control

over the air supply in an emergency, even if a hose is ruptured.

3. Discontinue tool use if it does not work properly or air is leaking.

Tag or mark the tool as ‘defective’ or ‘out of service’ until repaired.

4. Check the manufacturer’s maximum pressure rating for air tools

and accessories. Compressor outlet pressure must be regulated to

never exceed the maximum pressure rating of the tool (see

Specifications). Exceeding the maximum PSI rating can create a

bursting hazard, causing injury and property damage.

4.1 Do not exceed maximum working air pressure at 90 PSI

(6.2 bar).

5. Attach all accessories properly to the tool before connecting the air

supply. A loose accessory may detach or break during operation.

6. Never use oxygen, combustible gas or any other bottled gas as a

power source. Any power source other than an air compressor

could cause an explosion and serious personal injury.

V1.0 3/8 in. Air Impact Wrench 8843997

Visit www.princessauto.com for more information 7

7. Turn OFF the valve and discharge any remaining air pressure after

each use or before adjusting the tool.

8. Do not leave the air tool unattended with its compressed air supply

on. Turn off the compressed air supply and bleed the air tool of any

remaining compressed air before leaving the air tool unattended.

9. Serious injury may occur from loose debris being propelled at high

speeds from the compressed air stream. Always wear OSHA

approved safety glasses to protect the eyes during operation of the air

compressor.

10. Always turn off the air compressor and drain tank pressure

completely before attempting maintenance or attaching air tools.

Release pressure slowly from the system.

AIR HOSE PRECAUTIONS

1. Inspect the tool's air hose for cracks, fraying or other faults before

each use. Discontinue use if the air hose is damaged or hissing is

heard from the air hose or couplers. Replace the defective air

hose.

2. Do not allow people, mobile equipment or vehicles to pass over the

unprotected air hose. Position the air hose away from high traffic

areas, in a reinforced conduit or place planks on both sides of the

air hose to create a protective trench.

3. Prevent damage to the air hose by observing the following:

3.1 Never carry the tool by the air hose.

3.2 Keep the air hose behind the tool and out of the tool's work

path.

3.3 Keep the air hose away from heat, oil, sharp edges or moving

parts.

3.4 Do not wrap the air hose around the tool as sharp edges may

pierce or crack the air hose. Gently coil the hose and either

hang on a hook or fasten with a device to keep hose together

when storing.

4. A damaged or disconnected air hose under pressure may whip

around and inflict personal injury or damage the work area. Secure

the compressor's air hose to a fixed or permanent structure with

clamps or cable ties.

8843997 3/8 in. Air Impact Wrench V1.0

8 For technical questions call 1-800-665-8685

5. Before connecting the hose, clean the hose by blowing out with

compressed air. This will prevent moisture and/or dust in the hose

from entering the tool causing rust and/or malfunction.

VIBRATION PRECAUTIONS

1. This tool vibrates during use. Repeated or long-term exposure to

vibration may cause temporary or permanent physical injury. Take

frequent breaks when using the tool.

2. If you feel any medical symptoms related to vibrations (such as

tingling, numbness, and white or blue fingers), seek medical

attention as soon as possible.

3. Wear suitable gloves to reduce the effects of vibration.

4. DO NOT use this tool before consulting a physician if one of the

following applies:

a. Pregnant

b. Impaired blood circulation to

the hands

c. Past hand injuries

d. Nervous system disorders

e. Diabetes

f. Raynaud's Disease

5. Do not use worn or ill-fitting sockets or extensions as this is likely to

cause a substantial increase in vibration.

UNPACKING

WARNING! Do not operate the tool if any part is missing. Replace

the missing part before operating. Failure to do so could result in

a malfunction and personal injury.

Remove the parts and accessories from the packaging and inspect for

damage.

ASSEMBLY & INSTALLATION

Dashed numbers in parenthesis (Fig. 1-1) refer to a specific point in an

illustration or image.

INSTALL AIR COUPLER PLUG

Prepare a standard 1/4 in. NPT coupler plug (sold separately) for use

with your tool.

1. Wrap the external threads of the coupler plug with sealant tape.

V1.0 3/8 in. Air Impact Wrench 8843997

Visit www.princessauto.com for more information 9

1.1 Wrap tape in a clockwise direction so it will not unravel.

1.2 Do not tape all the threads. Leave several leading threads

unwrapped for easier alignment.

2. Screw the coupler plug into the tool's air inlet and tighten with a

wrench until snug.

3. Run the compressor at a low volume and check the connection for

air leaks. Do not use the tool until all air leaks are repaired or the

faulty component is replaced.

IMPORTANT! Vibration may cause failure if a quick coupler is

connected directly to the air tool. To overcome this, connect a

leader hose to the tool. A quick coupler may then be used to

connect the leader hose to the air line hose.

OPERATION

CAUTION! Injury Hazard! To avoid injury, always disconnect the air

supply to the tool when attaching or removing sockets or accessories.

Use only sockets and accessories rated for impact use.

1. Disconnect the air supply.

2. Snap the socket or accessory over the retaining ring nested in the

square drive.

3. Connect the air supply, hold the tool securely and press the trigger

to begin the rotating action.

4. To loosen fasteners, move the lever (Fig. 1-1) on the back of the

drive head counter-clockwise to align the

arrow to the reverse arrow (Fig. 1-2).

5. To tighten fasteners, move the lever

clockwise and align the arrow to select

either low (Fig. 1-3), medium (Fig. 1-4),

or high torque (Fig. 1-5) settings (small,

medium or large circles).

6. Place the socket over the fastener, grip the impact wrench firmly

with both hands and gently squeeze the trigger.

6.1 If the tool stalls while tightening, do not raise the output

pressure of the air compressor above 90 PSI. Pressure above

90 PSI will strip the workpiece and damage the tool,

Fig. 1

8843997 3/8 in. Air Impact Wrench V1.0

10 For technical questions call 1-800-665-8685

potentially causing tool failure and serious injury. Use other

appropriate methods and tools to tighten the nut.

7. This tool will stop operation/rotation a few seconds after the trigger

is released.

8. When the fastener is tightened, release the trigger and remove the

tool and socket.

9. Use a mechanical torque wrench to check the fastener torque.

10. When finished with the tool, turn off the air compressor, disconnect

the air hose and discharge any residual air remaining in the tool.

Put the impact wrench away in a safe storage area.

PRESSURE DROP

Apply the air consumption and pressure rate numbers to the tool’s air

inlet, not the compressor’s outlet. Calculate the pressure drop for your

air supply set-up and increase the compressor outlet pressure to

compensate. Make sure you do not exceed the maximum pressure for

any part of your air supply system.

Installing a pressure gauge at the tool inlet is the best way to measure

the air pressure and adjust the compressor’s output.

CARE & MAINTENANCE

1. Maintain the tool with care. A tool in good condition is efficient,

easier to control and will have fewer problems.

2. Inspect the tool fittings, alignment and hoses periodically. Have

damaged or worn components repaired or replaced by an authorized

technician. Only use identical replacement parts when servicing.

3. Follow instructions for lubricating and changing accessories.

4. Only use accessories intended for use with this tool.

5. Keep the tool clean, dry and free from oil/grease at all times.

6. Maintain the tool’s labels and name plates. These carry important

information. If unreadable or missing, contact Princess Auto Ltd. for

replacements.

WARNING! Only qualified service personnel should repair the

tool. An improperly repaired tool may present a hazard to the

user and/or others.

V1.0 3/8 in. Air Impact Wrench 8843997

Visit www.princessauto.com for more information 11

AIR TOOL LUBRICATION

NOTICE! Only use air tool oil to lubricate the tool. Other

lubricants are not suitable and will damage the tool or cause a

malfunction during use.

NOTICE! Never use a penetrating oil to lubricate an air tool.

Penetrating oil acts as a solvent that will dissolve the tool’s

grease packing and may damage the o-rings, causing the tool to

seize or malfunction.

1. All air tools have an internal coating of grease to prevent corrosion

during shipping and storage. Remove this grease by adding a

generous amount of air tool oil in the air inlet and then run the tool

under no load until the exhaust is clear.

2. Manually add a drop or two of air tool oil into the tool’s coupler

plug before each use and after every hour of continuous use. The

tool will not work properly without lubrication and parts will wear

prematurely.

3. Avoid adding too much air tool oil as this can cause premature

power loss and eventual tool failure. A qualified technician will need

to take the tool apart and clean out the excess oil.

4. Apply a generous amount of air tool oil to the tool before storing it

for an extended period of time (overnight, weekend, etc.). Run the

tool for approximately 30 seconds to ensure the oil is evenly

distributed throughout the tool. Store it in a clean and dry location.

DISPOSAL

Recycle a tool damaged beyond repair at the appropriate facility.

Contact your local municipality for a list of disposal facilities or by-laws for

electronic devices, batteries, oil or other toxic liquids.

IMPORTANT! DO NOT pollute the environment by allowing

uncontrolled discharge of waste oil.

TROUBLESHOOTING

Visit a Princess Auto Ltd. location for a solution if the tool does not

function properly or parts are missing. If unable to do so, have a

qualified technician service the tool.

8843997 3/8 in. Air Impact Wrench V1.0

12 For technical questions call 1-800-665-8685

PROBLEM(S) POSSIBLE CAUSE(S) SUGGESTED SOLUTION(S)

Tool runs at

normal

speed, but

loses power

under load.

Motor parts worn. 1. Have a qualified technician service

the tool.

2. Replace tool or parts.

Tool runs

slowly. Air

flows slightly

from exhaust.

Motor parts jammed

with dirt particles.

Airflow blocked by dirt.

1. Check air inlet filter for blockage.

2. Pour air tool lubricating oil into air

inlet as per lubrication instructions

for clearing shipping grease.

3. Operate tool in short bursts to

clear debris.

4. If tool still jammed, clean tool and

lubricate per lubrication

instructions.

Tool runs

slowly. Air

flows slightly

from exhaust.

1. Air regulator in

closed position.

Damage or excessive

wearing of internal

parts.

1. Open the air regulator to desired

airflow.

2a. Have a qualified technician

service the tool.

2b. Replace tool or parts.

Tools will not

run. Air flows

freely from

exhaust.

Damage or excessive

wearing of internal parts.

1. Have a qualified technician

service the tool.

2. Replace tool or parts.

Tool will not

shut off.

1. Throttle valve o-ring

dislodged from inlet

valve seat.

2. Trigger mechanism

jammed or dirty.

1. Replace throttle valve

o-rings.

2. Clean trigger mechanism and

lubricate.

Loss of

power or

erratic

performance.

1. Excessive drain on

the air hose.

Incorrect size or type

of hose connectors.

2. Moisture or

restriction

in the air hose/tank

3. Air compressor has

insufficient flow.

1. Check the air hose

and confirm the

hose fitting is correct for the inlet

bushing.

2. Depressurize system and drain

tank and air hose of water.

3. Ensure tool is connected to a

compressor with a rate flow that

matches the tool.

V1.0 3/8 in. Air Impact Wrench 8843997

Visit www.princessauto.com for more information 13

PARTS BREAKDOWN

PARTS LIST

DESCRIPTION

QTY

1 Motor Housing Assembly

(including 38)

Air Inlet

3 O-ring 1

4 Exhaust Deflector 1

5 O-Ring 2

6 Spring 1

7 Throttle Valve Assembly

(including 7-1 and 7-2)

7-1

Throttle Valve Pin

7-2 Throttle Valve 1

8 Throttle Valve Seat 1

9 O-Ring 1

10 Trigger Assembly

(including 11 and 12)

11 Trigger Pin 1

12 O-Ring 1

13 Spring Pin 1

14 Gasket 1

8843997 3/8 in. Air Impact Wrench V1.0

14 For technical questions call 1-800-665-8685

15 O-Ring 1

Reverse Valve

17 Forward/Reverse Lever 1

O-Ring

19 Rear Housing 1

21 Ball Bearing 1

22 Rear End Plate 1

23 Rotor 1

24 Rotor Blade 6

25 Spring Pin 3

26 Cylinder 1

27 Front End Plate 1

28 Ball Bearing 1

29 Gasket 1

30 Hammer Frame 1

31 Hammer 2

Hammer Pin

33 Anvil 1

O-Ring

35 Socket Retainer 1

Bushing

37 Hammer Case Assembly

(including 36 and 45)

38 Bushing 1

39 Screw 4

40 Pin 1

41 Spring 1

42 Muffler Element 1

43 Spacer 1

44 Screw 1

45 Grease Fitting 1

TK Tune-up Kit (including

3.5(2), 6, 9, 14, 15, 17,

18, 24(6), 29, 34, 35,

41, 42)

V1.0 3/8 in. Air Impact Wrench 8843997

Visit www.princessauto.com for more information 15

8843997 3/8 in. Air Impact Wrench V1.0

16 For technical questions call 1-800-665-8685

V1,0 8843997

Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil. Conservez ce

manuel afin de pouvoir le consulter plus tard.

CLÉ À CHOCS

PNEUMATIQUE



3/8 PO

8843997 Clé à chocs pneumatique de 3/8 po V1,0

2 En cas de questions techniques, appelez le 1-800-665-8685

SPÉCIFICATIONS

Format de prise carrée 3/8 po

Couple max. 350 pi-lb

Vitesse nominale 13 000 tr/min

Débit moyen à un temps de

fonctionnement de 15 secondes

5,7 pi cubes/min

Débit à pleine charge 22 pi cubes/min

Pression nominale 90 lb/po carré

Entrée d’air 1/4 po

Matériau Boîtier en composite avec prise coussinée

DÉFINITIONS DE DANGER

Veuillez-vous familiariser avec les avis de danger qui sont présentés dans

ce manuel. Un avis est une alerte indiquant qu'il existe un risque de

dommage à la propriété, de blessure ou de décès si on ne respecte pas

certaines instructions.

DANGER ! Cet avis indique un risque immédiat et particulier qui

entraînera des blessures corporelles graves ou

même la mort si on omet de prendre les précautions

nécessaires.

AVERTISSEMENT ! Cet avis indique un risque particulier ou une pratique

non sécuritaire qui pourrait entraîner des blessures

corporelles graves ou même la mort si on omet de

prendre les précautions nécessaires.

ATTENTION ! Cet avis indique une situation possiblement

dangereuse qui peut entraîner des blessures

mineures ou modérées si on ne procède pas de la

façon recommandée.

AVIS ! Cet avis indique un risque particulier ou une pratique

non sécuritaire qui entraînera des dommages au

niveau de l'équipement ou des biens, mais non des

blessures corporelles.

V1,0 Clé à chocs pneumatique de 3/8 po 8843997

Visitez www.princessauto.com pour plus d'informations 3

INTRODUCTION

Cette clé à chocs pneumatique en composite à prise de 3/8 po

possède un boîtier en composite avec une prise coussinée et un couple

maximal de 350 pi-lb. L’outil possède un couple variable en marche

avant et en marche arrière.

SÉCURITÉ

AVERTISSEMENT ! Veuillez lire et comprendre toutes les

instructions avant d'utiliser cet outil. L'utilisateur doit respecter

les précautions de base lorsqu'il utilise cet outil afin de réduire

le risque de blessure ou de dommage à l'équipement.

Conservez ce manuel qui contient les avertissements de sécurité, les

précautions, les instructions de fonctionnement ou d'inspection et

d'entretien.

AIRE DE TRAVAIL

1. Travaillez dans un environnement de travail sécuritaire. Gardez

votre aire de travail propre, bien éclairée et exempte de toute

distraction. Placez les lampes de façon à ne pas travailler dans

l’ombre.

2. Assurez-vous que les personnes qui ne portent pas l'équipement de

sécurité approprié ne se trouvent pas à proximité de l'aire de travail.

3. Rangez les outils correctement dans un lieu sécurisé et sec.

Gardez les outils hors de la portée des enfants.

4. N'installez pas et n'utilisez pas d'outils électriques en présence de

gaz, de poussière ou de liquides inflammables.

SÉCURITÉ PERSONNELLE

AVERTISSEMENT ! Portez de l'équipement de protection personnelle

homologué par l'Association canadienne de normalisation (CSA) ou

l'American National Standards Institute (ANSI).

ÉQUIPEMENT DE PROTECTION PERSONNELLE

1. Portez toujours des lunettes antiprojections qui offrent une

protection frontale et latérale pour les yeux. L'équipement de

protection des yeux devrait être conforme à la norme CSA Z94.3-

07 ou ANSI Z87.1 fonction du type de travail effectué.

8843997 Clé à chocs pneumatique de 3/8 po V1,0

4 En cas de questions techniques, appelez le 1-800-665-8685

2. Portez un écran facial panoramique de type approprié avec les

lunettes de sécurité puisque cette tâche peut créer des copeaux,

des matières abrasives ou des particules.

3. Portez des gants qui protègent en fonction des matériaux de travail

et pour réduire les effets des vibrations de l'outil.

3.1 Ne portez pas de gants lorsque vous utilisez un outil dans

lequel le tissu pourrait demeurer coincé, entraînant ainsi la

main.

4. Portez des vêtements de protection conçus pour l'environnement

de travail et pour l'outil.

5. Les chaussures antidérapantes sont recommandées pour maintenir

la stabilité et l'équilibre au sein de l'environnement de travail.

6. Cet outil peut causer des dommages à l'ouïe. Portez un dispositif

de protection anti-bruit présentant une cote de réduction du bruit

adéquate en fonction du niveau de décibels.

7. L’outil peut être à haute pression. Portez des lunettes de sécurité et

des gants pour vous protéger au cours de l'opération. Gardez les

mains à l'écart des parties de caoutchouc exposées du tuyau.

PRÉCAUTIONS PERSONNELLES

1. N'utilisez pas l'outil si vous êtes fatigué ou sous l'effet de drogues,

d'alcool ou de médicaments.

2. Évitez de porter des vêtements ou des bijoux pouvant se prendre dans

les pièces mobiles d'un outil. Gardez les cheveux longs recouverts ou

attachés.

3. N'utilisez pas l'outil si vous devez étirer les bras pour vous en

servir. Une stabilité et un équilibre appropriés sont nécessaires afin

d'avoir un meilleur contrôle en cas de situations inattendues.

4. Gardez vos doigts à bonne distance de la gâchette/commutateur

lors du transport de l’outil ou du branchement d’un tuyau à air ou

d’un accessoire. Engagez le verrou de gâchette/interrupteur, le cas

échéant.

5. Évitez les mises en marche involontaires. Assurez-vous que le

régulateur/commutateur est en position neutre ou OFF (arrêt)

lorsque l’outil n’est pas utilisé et avant de le brancher à une source

d’air.

La page est en cours de chargement...

PROPOINT 8843997 Le manuel du propriétaire

Marque: PROPOINT

Modèle: 8843997

Catégorie: Coupe-bordures

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: PROPOINT 8843997 Owner's manual

PROPOINT 8843997 Le manuel du propriétaire

PROPOINT 8843997 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents