Pentair GreatWhite GW9500 Manuel utilisateur

Automatic Pool Cleaner

Installation and

User’s Guide

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

This document is subject to change without notice

1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-8000

10951 West Los Angeles Ave., Moorpark, CA 93021 • (805) 553-5000

Trademarks and Disclaimers:

Great White® and Pentair Water Pool and Spa® are registered trademarks of Pentair Water Pool and Spa, Inc.

and/or its affiliated companies in the United States and/or other counties. Unless noted, names and brands of

others that may be used in this document are not used to indicate an affiliation or endorsement between the

proprietors of these names and brands and Pentair Water Pool and Spa, Inc. Those names and brands may be the

trademarks or registered trademarks of those parties or others.

PN789 (Rev C) - 1/24/11

Technical Support

Sanford, North Carolina (8 A.M. to 5 P.M.)

Moorpark, California (8 A.M. to 5 P.M.)

Phone: (800) 831-7133

Fax: (800) 284-4151

Web sites: visit www.pentairpool.com and staritepool.com

i

Great White Installation and User’s Guide

Contents

Important Safety Precautions ..............................................................................ii

Section 1: Overview ............................................................................................1

Preparation of your pool ............................................................................... 2

Cleaner assembly ............................................................................ 2

Hose Assembly ................................................................................ 3

Section 2: Installation ..........................................................................................5

Standard Installation..................................................................................... 5

Optional Installation...................................................................................... 8

Section 3: Operation............................................................................................11

Cleaner Operation and Movement ............................................................... 11

Clicking sound ................................................................................ 11

Movement around the pool ............................................................... 11

Picks up “big stuff” ....................................................................................... 11

Fine-tuning valves and connections ............................................................ 12

Valves (pump, skimmer, and main drain) and vacuum adjustments 12

Too much vacuum? ......................................................................... 12

Not enough vacuum? ....................................................................... 12

In-Line leaf canisters ........................................................................ 13

Skimmer connection ........................................................................ 13

Skimmer vac plates ......................................................................... 13

Skimmer vac plate vacuum control adjusters .................................. 13

Section 4: User Maintenance ............................................................................. 15

Hose Storage ............................................................................................... 15

Disassembly................................................................................................ 16

Reassembly ................................................................................................ 17

Illustrated Parts List ..................................................................................... 18

Section 5: Troubleshooting ................................................................................19

ii

Great White Installation and User’s Guide

Important Notice:

Attention Installer: This manual contains important information about the installation, operation and safe use

of this product. This information should be given to the owner and/or operator of this equipment.

WARNING — Before installing this product, read and follow all warning notices and instructions which

are included. Failure to follow safety warnings and instructions can result in severe injury,

death, or property damage. Call (800) 831-7133 for additional free copies of these

instructions.

WARNING — Hazardous suction. Can trap and tear hair or body parts. Can cause drowning.

Do not play with cleaner or hose or apply to body. Do not let children use or play

with pool cleaner. Stop pump before attempting to clean unit.

CAUTION — Oscillator may injure hands or fingers. Stop pump before attempting to clean out

pool cleaner head.

WARNING — Hose can trip or entangle swimmers. Do not allow swimmers in pool while pool cleaner

is operating.

IMPORTANT SAFETY PRECAUTIONS

1058 0594

General Installation Information

Pre-installation check list

Before installing the cleaner in a vinyl liner pool:

Check liner closely for signs of deterioration or damage from age, chemicals, pool wall damage, etc. If any

damage is found, have a qualified pool professional make all necessary repairs. Also, if there are stones, roots,

etc., under the liner, remove them before installing the cleaner.

Before installing the cleaner in a gunite pool or a pool that is partially or completely tiled:

Repair loose tiles and tighten any loose light rings.

Before installing the cleaner, clean your filter system:

Make sure you have cleaned the filter, including backwashing, rinsing, and emptying all baskets. A clean

system is necessary for proper cleaner operation and coverage.

iii

Great White Installation and User’s Guide

General Installation Information (continued)

Before installing the cleaner, fill the hose with water:

Always make sure the cleaner head is submerged and the hose is full of water before connecting the hose to

the filtration system (whether through a skimmer or dedicated wall fitting). Air in the system can damage the

pump through dry running and overheating.

Before installing the cleaner, understand cleaner coverage:

The cleaner is designed to rid your pool of debris in approximately 4-6 hours. Less time could be needed,

depending on the pool size.

The cleaner was not designed to automatically clean steps or swimouts or to work under a solar cover. It was

also not designed to do initial cleanup for a new pool or when opening your pool for the season.

WARNING — Suction entrapment, injury, and drowning hazard. If your pool has a dedicated

suction port (“vac port”) for vacuuming or for an automatic pool cleaner, it must be

covered when not in use.

A spring loaded safety cover is included with your cleaner. Install it on the suction port to prevent entrapment

and injury.

IMPORTANT SAFETY PRECAUTIONS (continued)

iv

Great White Installation and User’s Guide

Blank Page

1

Great White Installation and User’s Guide

Section 1

Overview

Great White Automatic Inground Pool Cleaner

Congratulations on your purchase of the world’s best pool cleaner! Nothing quite compares to the Great

White’s ability to make dirt disappear. With its 15” cleaning path and unique bristle drive, your Great White

automatic, inground pool cleaner will deliver fast, complete coverage of your pool.

Great White Automatic Inground Pool Cleaner

Model GW9500

2

Great White Installation and User’s Guide

Preparation of your pool

Before you assemble and install your Great White automatic pool cleaner, you should make sure that your

pool is clean and free of algae. If necessary, make the following preparations before proceeding.

• Chemically balance the pool water

• Brush the pool and let the debris settle

• Hand vacuum the pool thoroughly

• Clean the filter and pump strainer basket (Figure 1)

Cleaner assembly

1. Check parts

Remove Great White and all of its parts from the box and check to make sure that all components were

included (Figure 2).

Cleaner

Swivel Assembly

Handle Adapter

Reducer Cone

Hose: Twelve 4’ lengths

Vacuum Regulator

Regulator Cap

Vacuum Port Fitting

Flow Gauge

2. Attaching swivel assembly to cleaner head

Installing the swivel assembly is a snap. Just insert it into the cleaner body and give it a quarter turn

(Figure 3). If you attach a unidapt handle to the swivel for manual vacuuming, be sure it is the special,

floating unidapt handle provided with the cleaner (Replacement Part No. GW9019). Use of a different

unidapt handle will hinder the cleaner’s performance.

Vacuum

Regulator

Cap

Swivel

Ass'y Reducer

Cone

Vacuum

Port Fitting

Flow

Gauge

Handle Adapter

Cleaner

M

A

X

I

M

U

M

F

L

O

W

M

I

N

I

M

U

M

F

L

O

W

Hose

Twelve

4’ lengths

Figure 3

Figure 1

Swivel

Assembly

Figure 2

Skimmer

Basket

Pump

Straine

r

3

Great White Installation and User’s Guide

Hose Assembly

Assemble the hose

The unit includes twelve sections of hose, each 4 feet (4’) in length (Figure 4). Do not cut the

hose lengths. You will need to connect these 4’ sections of hose to create a combined hose length that is

at least 4’ longer than the distance from your suction source (whether

skimmer or dedicated suction line) to the farthest point in the pool

(Figure 5). Connect the hoses by twisting and pushing the female ends

onto the male ends after wetting the ends in the pool (Figure 6). A

special “leader” hose section is designed to connect to the

cleaner’s swivel assembly and therefore has a larger hose cuff

than the other hose lengths (Figures 7 and 8). Failure to use this

leader hose section to attach the hose to the cleaner’s swivel assembly

will hinder your cleaner’s performance. If additional hose is needed,

use only hoses from your Pentair Water Pool and Spa dealer (order replacement part No. 41200-0131).

Use of another manufacturer’s hose will hinder cleaner coverage.

Figure 6

Figure 5

Hose must equal longest stretch — — plus at least 4 feet.

Swivel

Assembly

Leader Hose

Figure 8

Figure 4

Hose

Twelve, 4’ lengths

Figure 7

Female hose end Male hose end

Leader Hose

Connect to Swivel Assembly

4

Great White Installation and User’s Guide

Blank Page

5

Great White Installation and User’s Guide

Section 2

Installation

This section describes how to install the Great White pool cleaner. Great White is designed to work in a wide

variety of swimming pools. Both the standard in-skimmer installation and optional vac port installation are

covered below. If your pool configuration is unlike any of the examples, contact your Pentair Water Pool and

Spa dealer for assistance, or call our toll-free Customer Helpline at 1-800-831-7133.

Standard Installation

For pools with one skimmer, using the vacuum regulator



The manufacturer recommends the Standard Installation through the pool’s skimmer (Figure 8)

The advantage of this installation is its use of the vacuum regulator (Figure 9) to balance the water

flow between the skimmer and the Great White pool cleaner. The vacuum regulator can be adjusted

to changes in the amount of water flow to provide Great White with the power necessary to ensure

proper cleaning performance, and the manufacturer strongly recommends its use for maximum safety

and performance.

1. Turn the pool pump off

2. Adjust valves for vacuuming

Adjust the pump valves (if your system has valves) to direct all suction to the skimmer. Close the main drain

and all suction lines, except the line from the skimmer to which Great White will be connected.

3. Remove the skimmer basket from the skimmer

4. Install vacuum regulator

WARNING! Hazardous suction. Can cause entrapment with severe personal injury or drowning.

Use the vacuum regulator in conjunction with your pool cleaner system at all times. The vacuum regulator

has an adjustment knob (Figure 9). If suction is too high, the knob is turned counterclockwise to decrease

the suction. If the suction is too low, the knob is turned clockwise to increase the suction.

Figure 8

Skimmer

Figure 9

Adjustment

Knob

Vacuum

Regulator

6

Great White Installation and User’s Guide

Standard Installation (Continued)

The vacuum regulator must be installed in conjunction with the reducer cone (Figure 10). The reducer cone

is required to make most skimmer connections. It will keep the hose and vacuum regulator in place once

the filter system is stopped.

To install the vacuum regulator, insert the vacuum regulator and reducer cone in the skimmer. Attach the

end of the hose to the regulator (Figure 11).

Make sure the vacuum regulator is submerged at all times. If not, the pump will suck air through the

vacuum regulator and lose prime. This could damage the pump.

Figure 10

Figure 11: Vacuum regulator installed in the skimmer with the hose attached

Skimmer

Vacuum

Regulator

To Pump

Reducer Cone

7

Great White Installation and User’s Guide

Standard Installation (Continued)

5. Check Flow

With the main drain closed, and one end of the hose attached to the regulator installed in the skimmer, insert

the flow gauge into the other end of the hose. Keep the hose and flow gauge underwater. Turn on the

pump. With the pump running, adjust the vacuum regulator (in your skimmer) until the indicator on the flow

gauge is between minimum and maximum flow (Figure 12). Remove the flow gauge and proceed to step 6.

6. Connect Hose to the Cleaner’s Swivel Assembly

Connect the large hose cuff (Figure 13) of the leader hose to the swivel assembly on the cleaner head

(Figure 13). Push the cleaner into the pool and let it sink to the bottom (Figure 14).

Figure 14

Disc Indicator

Figure 12

Figure 13

Large hose cuff

of leader hose

designed to connect

to swivel assembly

(See “Hose Assembly”

on Page 3)

7. Turn the pool pump on

After completing the installation, turn the pool pump on and allow it to run for a couple of minutes to ensure

that all air cycles out of the system.

8

Great White Installation and User’s Guide

Optional Installation

Vac Port Installation with Vacuum Regulator in Skimmer



If your pool has a vac port (Figure 15), you can install Great White using the Optional Installation.

1. Turn the pool pump off

2. Adjust valves for vacuuming

Adjust the pump valves (if your system has valves) to direct all suction to the dedicated vacuum line and the

skimmer. Close the main drain and all suction lines, except the line from the dedicated vacuum line to which

Great White will be connected, and the skimmer where the vacuum regulator will be installed.

3. Install vac port door fitting

WARNING! Suction entrapment, injury, and drowning hazard. If your pool has

a dedicated suction port (“vac port”) for vacuuming or for an automatic pool

cleaner, it must be covered when not in use.

A spring loaded safety cover (the “vac port fitting”) is included with this pool cleaner

(Figure 16). Install it on the dedicated vacuum line to prevent entrapment and injury. For

details please refer to the Vac Port Instruction sheet included with your vac port fitting.

To install the included vac port fitting:

1. Screw the vac port fitting into the dedicated vacuum line opening.

2. Orient the vac port fitting so the arrow on the door points up.

3. Secure the cover by tightening the allen-screw below the door, into the dedicated

vacuum line fitting.

4. Remove the skimmer basket from the skimmer

Figure 16

Figure 15

Vac Port

9

Great White Installation and User’s Guide

Optional Installation (continued)

5. Install vacuum regulator

WARNING! Hazardous suction. Can cause entrapment with severe personal injury or drowning.

To install the vacuum regulator, insert the vacuum regulator and reducer cone in the skimmer (Figure 17).

To prevent water from flowing through the top of the vacuum regulator, attach the regulator cap to the vacuum

regulator (Figure 18). Attach the end of the hose to the vac port fitting installed in the dedicated vacuum line

(Figure 17).

Vacuum

Regulator

Regulator Cap

Reducer Cone

To Pump

Skimmer

Figure 18: Vacuum regulator installed in the skimmer with the regulator cap attached

Water

Level

1900 0405

Reducer

Cone

Vacuum

Regulator

with Regulator

Cap attached

Skimmer

Gate valve for

vacuum port must

be fully open

Attach hose to

vac port

Figure 17: Vacuum regulator and reducer cone inserted in skimmer

10

Great White Installation and User’s Guide

Optional Installation (Continued)

6. Check Flow

With the main drain closed, and one end of the hose attached to the vac port fitting installed in the dedicated

vacuum line, insert the flow gauge into the other end of the hose. Keep the hose and flow gauge

underwater. Turn on the pump. With the pump running, adjust the vacuum regulator (in your skimmer) until

the indicator on the flow gauge is between minimum and maximum flow (Figure 19). Remove the flow

gauge and proceed to step 7.

7. Connect Hose to the Cleaner’s Swivel Assembly

Connect the large hose cuff (Figure 20) of the leader hose to the swivel assembly on the cleaner head.

Push the cleaner into the pool and let it sink to the bottom (Figure 21).

Disc Indicator

Figure 19

Figure 20

Large hose cuff

of leader hose

designed to connect

to swivel assembly

(See “Hose Assembly”

on Page 3)

Figure 21

8. Turn the pool pump on

After completing the installation, turn the pool pump on and allow it to run for a couple of minutes to ensure

that all air cycles out of the system.

11

Great White Installation and User’s Guide

Section 3

Operation

This section contains information describing the movement and operation of your Great White Cleaner, as

well as tips for “fine-tuning” your pool’s valves and connections to optimize Great White’s cleaning ability.

Cleaner Operation and Movement

Clicking sound

This is the sound of the oscillator moving back and forth in the oscillator chamber. The best speed for it is

about 500 oscillations per minute. The vibration created by the oscillator moves the bristles and the cleaner.

If the oscillator is running too fast, the cleaner will have a tendency to climb up the pool wall past the

waterline, or “walk out of the pool” and suck air. Reduce the speed by adjusting the vacuum regulator in

the skimmer.

Movement around the pool

Random motion – The cleaner will visit most spots in the pool within a six (6) hour period. It is not

specifically programmed, and cannot see the dirt you are seeing. It is a random motion pattern.

The cleaner was designed to spend most of its time in the deep end, where most of the floor and wall area

exists. During a six (6) hour period, the cleaner will visit the shallow end a few times.

Rotating motion – The cleaner will rise up on one side and pivot a few times per minute. This is normal

and provides the following:

1. Allows leaves that are being pushed or dragged along to be sucked up into the vacuum chamber.

2. Allows the cleaner to:

Change direction

Get out of corners

Get away from ladders

Submerge below pool water level

Get off of domed main drain covers

Picks up “big stuff”

The cleaner will pick up some debris so large that it may jam. Simply stop the pump and remove the debris

from the oscillator, or the swivel assembly.

12

Great White Installation and User’s Guide

Fine-tuning valves and connections

WARNING! Pool pump suction is hazardous and can cause entrapment with severe personal

injury or drowning. Use vacuum regulator (see instructions below) in pool cleaner system at all times.

NOTICE: Each pool’s hydraulic system and vacuum connections are different. Be sure you have installed

the vacuum regulator before you “fine-tune” the system. This not only regulates vacuum, but also acts as a

safety device.

WARNING! Suction entrapment, injury, and drowning hazard. If your pool has a dedicated suction

port (“vac port”) for vacuuming or for an automatic pool cleaner, it must be covered when not in use.

A spring loaded safety cover (the “Vac Port Fitting”) is included with this pool cleaner. Install it on the vac port to

prevent entrapment and injury. For details please refer to the Vac Port Fitting instruction sheet included with

your cleaner.

For the novice pool owner for whom pool vacuuming is a new experience, please read all of the following

points, installation instructions, and trouble shooting guide carefully.

Please note the following:

• “Vacuum” and “suction” are two words meaning the same thing.

• “Dedicated suction line”, “vac port”, and “vac fitting” are different terms for a hole in the side wall of

pool; this hole is connected to the pump suction and is dedicated to vacuuming.

• Some pools do not have a vac port. If your pool does have one, please read the “Suction Entrapment”

warning above.

For the seasoned pool owner: The automatic pool cleaner connection and vacuum adjustments can be

similar to using your manual pool vacuum. Please read on.

Valves (pump, skimmer, and main drain) and vacuum adjustments

You may need to spend some time adjusting the skimmer and main drain valves in order to obtain the best

vacuum setting for good cleaner operation. Once you have found the correct valve settings for best

operation, we suggest you mark the valves to ensure repeated success.

At first, set valves to give maximum vacuum to the skimmer or vac fitting you have elected to use.

Too much vacuum?

You have too much vacuum if the cleaner climbs up the pool wall past the water line to the point that the

cleaner sucks air and the pump loses prime. Frequent loss of prime will damage the pump. To correct this,

adjust the regulator by turning the adjustment knob counterclockwise. This will decrease the suction. If the

cleaner still climbs out and sucks air, open the main drain valve slightly.

13

Great White Installation and User’s Guide

Fine-tuning valves and connections (continued)

Not enough vacuum?

You don’t have enough vacuum if the cleaner moves sluggishly or not at all. Be sure the filter system is clean

and the regulator and all valves are adjusted to give you maximum vacuum. If the cleaner is still not moving,

your pump may not be strong enough to operate the cleaner. Please refer to “Troubleshooting” on Page 17.

In-Line leaf canisters

If your pool is exposed to large quantities of leaves, we suggest purchasing and installing an in-line leaf

canister (part no. R211084K). A leaf canister will provide more debris-loading capacity and also provides a

water by-pass when the canister is full. It is very important that the pump not starve for water!

Skimmer connection

For pools that have large quantities of “big stuff” to pick up, we suggest using the bottom of the skimmer

connection in conjunction with an in-line leaf canister (part no. R211084K). A leaf canister will provide

more debris-loading capacity and also provides a water by-pass when the canister is full. It is very

important that the pump not starve for water!

Skimmer vac plates

Some pool owners connect the hose to a skimmer vac plate, which allows the skimmer basket to remain in

the skimmer. If this method is used, empty the basket frequently. Also make sure that the vacuum regulator

provided is completely submerged so that it will not suck air and damage the pump.

Skimmer vac plate vacuum control adjusters

Some pool owners use one of a variety of manufacturer’s skimmer vac plates. Some have a vacuum control

adjuster, and some do not. The adjuster could be a screw-type, a spring loaded apparatus, or a dial design.

For those vac plates with adjusters, it is important to adjust them when fine tuning the vacuum for the

cleaner.

14

Great White Installation and User’s Guide

Blank Page

La page charge ...

Pentair GreatWhite GW9500 Manuel utilisateur

Pentair GreatWhite GW9500 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents