Snapper 7800980 Manuel utilisateur

80102136

Revision A

Not for

Reproduction

2 www.snapper.com

Manual Contents:

Operator Safety..................................................................... 2

Features and Controls..........................................................8

Operation............................................................................... 8

Maintenance.........................................................................14

Troubleshooting..................................................................27

Warranties............................................................................28

Slope Guide......................................................................... 31

Specifications......................................................................32

The images in this document are representative, and

are meant to complement the instructional copy they

accompany. Your unit may vary from the images

displayed.LEFTandRIGHTare as seen from the operator's

position.

Thank you for purchasing this quality-built Snapper

Walkbehind Mower. We’re pleased that you’ve placed your

confidence in the Snapper brand. When operated and

maintained according to the manuals, your Snapper product

will provide many years of dependable service.

The manuals contain safety information to make you aware

of the hazards and risks associated with the unit and how

to avoid them. This Walkbehind Mower was designed to be

used as described in operator's manual and is not intended

for any other purpose. It is important that you read and

understand the instructions thoroughly before attempting

to start or operate this equipment. Save these original

instructions for future reference.

This product requires final assembly before use. Refer to the

setup guide for instructions on final assembly procedures.

Follow the instructions completely.

Operator Safety

Safety Definitions

For your safety, the safety of others, and to protect the

performance of equipment, follow the precautions listed

throughout the manual before operation, during operation,

and during maintenance procedures.

indicates a potential personal injury hazard.

DANGER

indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING

indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION

indicates a hazardous situation which, if not avoided, could

result in minor or moderate injury.

NOTICE

indicates a situation which can cause damage to the

equipment, personal property and/or the environment, or

cause the equipment to operate improperly.

Safety Symbol Definitions

The following safety symbols may be found on the unit.

Read the operator’s manual before attempting to operate the

mower.

Mow across slopes, not up or down.

To avoid injury to others, do not mow when others, especially

children, are around.

To reduce the potential for fire, wait at least 2 minutes before

refueling.

To avoid serious injury or death, keep hands and feet away from

the mower deck at all times during operation.

To avoid injury from thrown objects, do not operate the mower

unless all mulching, discharge, or bagging components are in

their proper place.

California Spark Arrester Warning

WARNING

It is a violation of California Public Resource Code, Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined

in Section 4442, maintained in effective working order.

Other states or federal jurisdictions may have similar laws.

Contact the original equipment manufacturer, retailer, or

dealer to obtain a spark arrester designed for the exhaust

system installed on this engine.

Not for

Reproduction

3

WARNING

Battery posts, terminals, and related accessories

contain lead and lead compounds, chemicals known to

the State of California to cause cancer and birth defects

or other reproductive harm. Wash hands after handling.

California Proposition 65

This product can expose you to chemicals including

gasoline engine exhaust, which is known to the State of

California to cause cancer, and carbon monoxide, which

is known to the State of California to cause birth defects

or other reproductive harm. For more information go to

www.P65Warnings.ca.gov.

Operating Safety

Power equipment is only as safe as the operator. If it is

misused, or not properly maintained, it can be dangerous!

Remember, you are responsible for your safety and that of

those around you.

Use common sense, and think through what you are doing.

If you are not sure that the task you are about to perform can

be safely done with the equipment you have chosen, ask a

professional: contact your local authorized dealer.

Read the Manual

The operator’s manual contains important safety information

you need to be aware of BEFORE you operate your unit as

well as DURING operation.

Safe operating techniques, an explanation of the product’s

features and controls, and maintenance information is

included to help you get the most out of your equipment

investment.

Be sure to completely read the Safety Rules and Information

found on the following pages. Also completely read the

Operation section.

Children

Tragic accidents can occur with children. Do not allow them

anywhere near the area of operation. Children are often

attracted to the unit and mowing activity. Never assume that

children will remain where you last saw them. If there is a risk

that children may enter the area where you are mowing, have

another responsible adult watch them.

Slope Operation

3.5 ft

(1,5 m)

20.0 ft

(6,0 m)

You could be seriously injured or even killed if you use this

unit on too steep an incline. Using the unit on a slope that

is too steep or where you don’t have adequate footing or

traction can cause you to lose control or slip and fall.

You should not operate on inclines with a slope greater than

10 degrees, which is a 3.5 ft (1,5 m) rise over 20.0 ft (6,0 m).

Always mow across slopes, never up and down.

Also note that the surface you are mowing can greatly impact

control. Wet grass or leaves can seriously affect your footing

and traction on a slope.

If you feel unsure about operating the unit on an incline, don’t

do it. It’s not worth the risk.

Moving Parts

This equipment has moving parts that can injure you or

someone else. However, if you stand behind the handle

Not for

Reproduction

4 www.snapper.com

properly and follow all the rules in this book, the unit is safe to

operate.

The mower has a spinning mower blade that can amputate

hands and feet. Do not allow anyone near the equipment

while it is running!

To help you, the operator, use this equipment safely, it is

equipped with an operator present safety system. Do NOT

attempt to alter or bypass the system. See your dealer

immediately if the system does not pass all the safety

interlock system tests found in this manual.

Thrown Objects

This unit has a spinning mower blade. This blade can pick

up and throw debris that could seriously injure a bystander.

Be sure to clean up the area to be mowed BEFORE you start

mowing.

Do not operate this unit without the entire grass catcher or

discharge guard (deflector) in place.

Also, do not allow anyone in the area while the unit is running!

If someone does enter the area, turn the unit off immediately

until they leave.

Debris Accumulation

Accumulation of grass and debris can result in a fire. Be sure

to clean any accumulation of grass and debris with a brush or

compressed air, before and after operation.

Fuel and Maintenance

Gasoline is extremely flammable. Its vapors are also

extremely flammable and can travel to distant ignition

sources. Gasoline must only be used as a fuel, not as a

solvent or cleaner. It should never be stored any place where

its vapors can build up or travel to an ignition source like a

pilot light. Fuel belongs in an approved, plastic, sealed gas

can, or in the tractor fuel tank with the cap securely closed.

Spilled fuel needs to be cleaned up immediately.

Proper maintenance is critical to the safety and performance

of your unit. Be sure to perform the maintenance procedures

listed in this manual, especially periodically testing the safety

system.

General Safety Messages

WARNING

This powerful cutting machine is capable of amputating

hands and feet and can throw objects that can cause injury

and damage! Failure to comply with the following SAFETY

instructions could result in serious injury or death to the

operator or other persons. The owner of the machine

must understand these instructions and must allow only

persons who understand these instructions to operate

machine. Each person operating the machine must be of

sound mind and body and must not be under the influence

of any substance, which might impair vision, dexterity or

judgment.

WARNING

Engines give off carbon monoxide, an odorless, colorless,

poison gas. Breathing carbon monoxide can cause nausea,

fainting, or death.

• Start and run engine outdoors.

• Do not run the engine in an enclosed area, even if

doors or windows are open.

Protection For Children

Tragic accidents can occur if the operator is not alert to the

presence of children. Children are often attracted to the

machine and the mowing activity. Never assume that children

will remain where you last saw them.

1. KEEP children out of the mowing area and under the

watchful care of a responsible adult other than the

operator.

2. DO NOT allow children in yard when machine is operated

and turn machine OFF if anyone enters the area.

3. DO NOT allow pre-teenage children to operate machine.

4. ALLOW only responsible adults & teenagers with mature

judgment under close adult supervision to operate the

machine.

5. DO NOT pull mower backwards unless absolutely

necessary. LOOK and SEE behind and down for children,

pets and hazards before and while backing.

6. USE EXTRA CARE when approaching blind corners,

shrubs, trees, or other objects that may obscure vision.

Slope Operation

1. Slopes are a major factor related to slip and fall

accidents, which can result in severe injury. All slopes

Not for

Reproduction

5

require extra caution. If you feel uneasy on a slope, DO

NOT mow it.

2. Mow across slopes, never up-and-down. Exercise

extreme CAUTION when changing directions on slopes.

DO NOT mow steep slopes or other areas where stability

or traction is in doubt. Refer to the Slope Guide at the

back of this manual.

3. Use extra care with grass catchers or other attachments;

these affect the handling and the stability of the machine.

Preparation

1. Read, understand, and obey instructions and warnings in

this manual and on the mower, engine and attachments.

Know the controls and the proper use of the mower

before starting.

2. Only mature, responsible persons shall operate the

machine and only after proper instruction.

3. Data indicates that operators age 60 and above, are

involved in a large percentage of mower-related injuries.

These operators should evaluate their ability to operate

the mower safely enough to protect themselves and

others from serious injury.

4. Handle fuel with extra care. Fuels are flammable

and vapors are explosive. Use only an approved fuel

container. DO NOT remove the fuel cap or add fuel with

engine running. Add fuel outdoors only with the engine

stopped and cool. Clean spilled fuel and oil from the

machine. DO NOT smoke.

5. Check the area to be mowed and remove all objects

such as toys, wire, rocks, limbs and other objects that

could cause injury if thrown by the blade or interfere with

mowing. Also note the location of holes, stumps, and

other possible hazards.

6. Keep people and pets out of the mowing area.

Immediately, STOP Blade, Stop engine and Stop mower

if anyone enters the area.

7. Check shields, deflectors, switches, blade controls and

other safety devices frequently for proper operation and

location.

8. Make sure all safety decals are clearly legible. Replace if

damaged.

9. Protect yourself when mowing and wear safety glasses,

long pants and substantial footwear. DO NOT mow

barefooted or with sandals.

10. Know how to STOP the blade and engine quickly in

preparation for emergencies.

11. Use extra care when loading or unloading the machine

into a trailer or truck.

12. Check grass catcher components frequently for signs of

wear or deterioration and replace as needed to prevent

injury from thrown objects going through weak or torn

spots.

Safe Handling Of Gasoline

To avoid personal injury or property damage, use extreme

care in handling gasoline. Gasoline is extremely flammable

and the vapors are explosive.

1. Extinguish all cigarettes, cigars, pipes and other sources

of ignition.

2. Use only an approved fuel container.

3. DO NOT remove fuel cap or add fuel with the engine

running. Allow the engine to cool before refueling.

4. DO NOT refuel the machine indoors.

5. DO NOT store the machine or fuel container inside where

there is an open flame, spark or pilot light such as on a

water heater or other appliances.

6. DO NOT fill fuel containers inside a vehicle or on a

truck or trailer bed with a plastic liner. Always place the

containers on the ground away from the vehicle before

filling.

7. Remove gas-powered equipment from the vehicle or

trailer and refuel it on the ground. If this is not possible,

then refuel equipment using a portable container, rather

than a gasoline dispenser nozzle.

8. DO NOT start gas powered equipment in enclosed

vehicles or trailers.

9. Keep the nozzle in contact with the rim of the fuel tank or

container opening at all times until fueling is complete.

DO NOT use a nozzle lock-open device.

10. If fuel is spilled on clothing, change clothing immediately.

11. DO NOT overfill a fuel tank. Replace fuel cap and tighten

securely.

Operation

1. DO NOT put hands or feet near or under rotating parts.

Keep clear of discharge area while engine is running.

2. STOP engine when crossing gravel drives, walks, or

roads, and under any conditions where thrown objects

might be a hazard.

3. Mow only in daylight or good artificial light.

4. DO NOT operate mower while under the influence of

alcohol or drugs.

5. After striking a foreign object or if the mower vibrates

abnormally, STOP the engine, disconnect and secure the

spark plug wire. Inspect the mower for any damage and

repair the damage before starting.

6. DO NOT mow near drop offs, ditches or embankments.

Operator could lose footing or balance.

7. STAY ALERT for holes and other hidden hazards. Tall

grass can hide obstacles. Keep away from ditches,

washouts, culverts, fences and protruding objects.

8. DO NOT mow on wet grass. Always be sure of your

footing. Keep a firm hold on the handle and walk, never

run. Slipping could cause injury.

9. ALWAYS stay behind handle when engine (motor) is

running.

Not for

Reproduction

6 www.snapper.com

10. DO NOT leave the machine with the engine running.

STOP BLADE and STOP ENGINE before leaving the

operators position for any reason.

11. Before cleaning, repairing or inspecting make certain

the engine, blade and all moving parts have STOPPED.

Disconnect and secure the spark plug wire away from

plug to prevent accidental starting.

12. STOP the engine and wait until the blade comes to

complete STOP before removing the grass bag and/or

clearing grass.

13. DO NOT operate the mower without the the entire grass

catcher, rear guard, or other safety devices in place and

working. DO NOT point discharge at people, passing

cars, windows or doors.

14. DO NOT discharge material against a wall or obstruction.

Material may ricochet back towards the operator.

15. Slow down before turning.

16. Watch out for traffic when near or crossing roadways.

17. DO NOT operate the engine in enclosed areas. Engine

exhaust gases contain carbon monoxide, a deadly

poison.

18. Only use accessories approved by the manufacturer.

See manufacturer’s instructions for proper operation and

installation of accessories.

Maintenance And Storage

1. DO NOT store the mower or fuel container inside where

fumes may reach an open flame, spark or pilot light

such as in a water heater, furnace, clothes dryer or other

gas appliance. Allow the engine to cool before storing

the machine in an enclosure. Store fuel containers out

of reach of children in a well ventilated, unoccupied

building.

2. Keep the mower and engine free of grass, leaves

or excess grease to reduce fire hazard and engine

overheating.

3. When draining the fuel tank, drain fuel into an approved

container outdoors and away from open flame.

4. Keep all bolts, especially blade bolts, nuts and screws

properly tight. Check that all cotter pins are in proper

position.

5. Always provide adequate ventilation when running

engine. Engine exhaust gases contain carbon monoxide,

a deadly poison.

6. Service the engine and make adjustments only when

engine is stopped. Remove the spark plug wire from the

spark plug and secure the wire away from the spark plug

to prevent accidental starting.

7. DO NOT change engine governor speed settings or

overspeed the engine.

8. Check the grass bag assembly frequently for wear or

deterioration to avoid thrown objects and exposure to

moving parts. Replace with a new bag if loose seams or

tears are evident. Replace slider or bag adapter if broken

or cracked.

9. Mower blades are sharp and can cut. Wrap the blades

or wear heavy leather gloves and use CAUTION when

handling them.

10. DO NOT test for spark by grounding the spark plug next

to the spark plug hole; the spark plug could ignite gas

exiting the engine.

11. Have the machine serviced by an authorized dealer at

least once a year and have the dealer install any new

safety devices.

12. Use only factory authorized replacement parts or

equivalent parts when making repairs.

13. Remove battery (if equipped) before making adjustments

or repairs.

Safety and Operation Decals

Reading this manual and the safety instructions it contains

will provide the basic knowledge necessary to operate this

mower safely and effectively. However, several safety and

operation decals have also been placed on the mower as a

reminder of this important information during operation.

The decals noted below are located on the mower. The safety

warnings and operation instructions they contain should be

carefully read, understood, and followed. Not following these

important warnings and instructions can result in serious

bodily injury or death.

If any of these decals are lost or damaged, replace them

immediately. Contact your dealer for replacement decals.

Compare Figure 1 with the table following.

Not for

Reproduction

7

1

A Drive Control

• Squeeze drive

control against

handle to

engage wheel

drive.

B OPC (Blade Control)

• Squeeze blade

control to start

and run engine

and blade.

• Release blade

control to stop

engine and

blade.

C Ground Speed

Control

• Move ground

speed control

toward Fast

(Rabbit) to

increase ground

speed.

• Move ground

speed control

toward Slow

(Turtle) to

decrease ground

speed.

D WARNING: Spark

Arrestor may be

required.

E WARNING: Avoid

Serious Injury or

Death

F DANGER: Keep

Hands and Feet

Away.

G DANGER: Amputation

and Thrown Object

Hazard.

G DANGER: Amputation

and Thrown Object

Hazard.

H WARNING: Cancer

and Reproductive

Harm.

I Engine Speed Control

• Move engine

speed control

lever toward

Slow (Turtle) to

decrease engine

speed.

• Move engine

speed control

lever toward

Fast (Rabbit) to

increase engine

speed.

• Move engine

speed control

lever past Fast

(Rabbit) to turn

on choke.

Not for

Reproduction

8 www.snapper.com

Features and Controls

Note:The figures and illustrations in this manual are provided

for reference only and may differ from your specific model.

Contact your dealer if you have questions.

Compare Figure 2 with the table following.

2

A Mulching Cover

B Rear Height Adjustment Latch (2)

C Oil Fill Cap and Dipstick

D Rope Start Handle

E Engine Speed Control

F Drive Control

G Blade Control

H Ground Speed Control

I Fuel Filler Cap

J Front Height Adjustment Latch (2)

Operation

Before Starting

1. Check the guards, deflectors, grass bag, and covers to

make sure all are in place and securely tightened.

2. Check the blade control (A, Figure 3), drive control (B),

and ground speed control (C) to insure they work freely.

3

3. Check the cutting height. Adjust to the desired height.

See Cutting Height Adjustment .

4. Check the engine oil:

• Make sure the mower is on a level surface.

• Clean the oil fill area of any debris.

• Remove the dipstick (A, Figure 4) and wipe with a

clean cloth.

• Insert and tighten the dipstick.

• Remove the dipstick and check the oil level. It should

be at the top of the full indicator (B) on the dipstick.

• If low, add oil slowly into the engine oil fill. See Oil

Recommendations . Do not overfill. After adding oil,

wait one minute and recheck the oil level.

• Replace and tighten the dipstick.

4

5. Add fuel to the tank:

• Make sure the mower is outside, where fumes can

safely dissipate.

• Remove the fuel fill cap (C, Figure 4).

Not for

Reproduction

9

• Fill the tank with fuel. See Fuel Recommendations

. To allow for expansion of the fuel, do not fill above

the bottom of the filler neck (D).

• Reinstall the fuel fill cap.

6. Clean the exterior surfaces of the cutting deck and engine

of any accumulation of spilled fuel, dirt, grass, oil, etc.

Keep the engine air intake screen and cooling fins clear

at all times.

7. Charge the battery. See Charging the Battery .

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty

Certified oils for best performance. Other high-quality

detergent oils are acceptable if classified for service SF, SG,

SH, SJ or higher. Do not use special additives.

Outdoor temperatures determine the proper oil viscosity for

the engine. Use the chart to select the best viscosity for the

outdoor temperature range expected.

A. SAE 30 - Below 40°F (4°C) the use of SAE 30 will result in hard

starting.

B. 10W-30 - Above 80°F (27°C) the use of 10W-30 may cause

increased oil consumption. Check oil level more frequently.

C. Synthetic 5W-30

D. 5W-30

Fuel Recommendations

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane / 87 AKI (91 RON). For high

altitude use, see below.

• Gasoline with up to 10% ethanol (gasohol) is acceptable.

NOTICE Do not use unapproved gasolines, such as E15

and E85. Do not mix oil in gasoline or modify the engine to

run on alternate fuels. Use of unapproved fuels will cause

damage to engine components,which will not be covered

under warranty.

To protect the fuel system from gum formation, mix a fuel

stabilizer into the fuel. See the appropriateOperator's

Manualfor recommendations. All fuel is not the same.

If starting or performance problems occur, change fuel

providers or change brands. This engine is certified to

operate on gasoline. The emissions control system for this

engine is EM (Engine Modifications).

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum 85

octane/85 AKI (89 RON) gasoline is acceptable.

For carbureted engines, high altitude adjustment is

required to maintain performance. Operation without this

adjustment will cause decreased performance, increased

fuel consumption, and increased emissions. Contact

a Briggs & Stratton Authorized Service Dealer for high

altitude adjustment information. Operation of the engine at

altitudes below 2,500 feet (762 meters) with the high altitude

adjustment is not recommended.

For Electronic Fuel Injection (EFI) engines, no high altitude

adjustment is necessary.

Starting the Mower

WARNING

Poisonous Gas Hazard

Engine exhaust contains carbon monoxide, a poisonous

gas that could kill you in minutes. You CANNOT see it,

smell it, or taste it. Even if you do not smell exhaust fumes,

you could still be exposed to carbon monoxide gas. If you

start to feel sick, dizzy, or weak while using this product,

shut it off and get to fresh air RIGHT AWAY. See a doctor.

You may have carbon monoxide poisoning.

• Operate this product ONLY outside far away from

windows, doors and vents to reduce the risk of carbon

monoxide gas from accumulating and potentially being

drawn towards occupied spaces.

• Install battery-operated carbon monoxide alarms or

plug-in carbon monoxide alarms with battery back-up

according to the manufacturer’s instructions. Smoke

alarms cannot detect carbon monoxide gas.

• DO NOT run this product inside homes, garages,

basements, crawlspaces, sheds, or other partially-

enclosed spaces even if using fans or opening doors

and windows for ventilation. Carbon monoxide can

quickly build up in these spaces and can linger for

hours, even after this product has shut off.

• ALWAYS place this product downwind and point the

engine exhaust away from occupied spaces.

The engine on your mower is equipped with the Briggs &

Stratton Ready Start™ System. This features a temperature-

controlled automatic choke. No additional steps are required

to start a cold engine.

1. Move the engine speed control (A, Figure 5, if equipped)

to the fast (‘Rabbit’) position.

2. Squeeze the blade control (B) against the handle.

3. Start the mower:

• Manual Start Models: Pull the rope start handle (C) to

crank the engine.

• Electric Start Models: Insert the key (D) into the

electric start switch. Turn the key to crank the engine.

Use short starting cycles, five seconds maximum,

and wait 1 minute between starting cycles.

Not for

Reproduction

10 www.snapper.com

4. To stop the engine (and blade), release the blade control.

5. After the engine starts, allow a brief warm-up until the

engine runs smooth before beginning mower operation.

5

Propelling the Mower

1. Start the mower.

2. Move the ground speed control (A, Figure 6) to the

desired speed position.

3. Squeeze the wheel drive control (B) against the handle

to engage the wheel drive and propel the mower forward.

Forward speed can be adjusted while the mower is

moving by changing the position of the ground speed

control.

6

Stopping the Mower

1. Stop forward motion of the mower by releasing the wheel

drive control.

2. Stop the engine and blade by releasing the blade control.

3. Electric Start Models: Remove the key from the electric

start switch.

Handle Height Adjustment

WARNING

Amputation Hazard

• DO NOT attempt any maintenance, adjustments or

service with engine and blade running.

• STOP engine and blade.

• Disconnect spark plug wire and secure away from spark

plug.

Burn Hazard

• Engine and components are HOT.

• Avoid serious burns, allow sufficient time for all

components to cool.

The height of the mower handle can be adjusted as follows:

1. Loosen the lower nuts (A, Figure 7) on each lower

handle.

2. Move the handle assembly (B) up or down until the

desired position is achieved.

3. Tighten the lower nuts on each lower handle to maintain

the desired position.

7

Not for

Reproduction

11

Cutting Height Adjustment

WARNING

Amputation Hazard

• DO NOT attempt any maintenance, adjustments or

service with engine and blade running.

• STOP engine and blade.

• Disconnect spark plug wire and secure away from spark

plug.

Burn Hazard

• Engine and components are HOT.

• Avoid serious burns, allow sufficient time for all

components to cool.

1. Pull the height adjusting latch (A, Figure 8) outward and

move to the desired cutting height.

8

2. Set all wheels at the same cutting height. The highest

cutting position is Notch 7 (Figure 9). The lowest cutting

position is Notch 1.

9

Mulching Operation

For best mulching results, cut up to a maximum of 1/3 of

grass blade length and recycle ONLY when grass is dry.

1. Set all wheels in the highest cutting position (Notch 7).

See Cutting Height Adjustment .

2. Move the engine speed control to the fast (Rabbit)

position.

3. Move the ground speed control to the slowest speed

setting.

4. Proceed mowing slowly. If the grass is very dense, lower

each rear wheel latch one notch lower than the front

wheel latches to improve mulching performance.

Note:The mulching cover should remain on the machine at

all times, unless alternate discharge operations are desired,

such as side discharging or bagging.

Removing the Mulching Cover

(Optional Accessory on Some Models)

WARNING

Amputation Hazard

• DO NOT attempt any maintenance, adjustments or

service with engine and blade running.

• STOP engine and blade.

• Disconnect spark plug wire and secure away from spark

plug.

Burn Hazard

• Engine and components are HOT.

• Avoid serious burns, allow sufficient time for all

components to cool.

1. Remove the knob nuts (A, Figure 10) and internal/

external tooth lock washers (B) securing the mulching

cover (C) to the mower deck.

2. Remove the cover.

10

Not for

Reproduction

12 www.snapper.com

Installing the Discharge Deflector

WARNING

Amputation Hazard

• DO NOT attempt any maintenance, adjustments or

service with engine and blade running.

• STOP engine and blade.

• Disconnect spark plug wire and secure away from spark

plug.

Burn Hazard

• Engine and components are HOT.

• Avoid serious burns, allow sufficient time for all

components to cool.

1. Remove the mulching cover. See Mulching Operation .

2. Install the deflector (A, Figure 11) to the deck in place of

the mulching cover, making sure that:

• The front hole (B) on the outside front of the deflector

fits over the stud where the front of the mulching

cover was originally secured;

• The slot (C) on top of the deflector slips under the

restraining nut on top of the deck (under the right

front corner of the engine);

• The slot (D) on the inside rear of the deflector slips

onto the stud behind the rear of the discharge

opening, where the rear of the mulching cover was

originally secured.

3. Install the internal/external tooth lock washers and knob

nuts onto the studs and tighten securely.

11

WARNING

Thrown Objects Hazard

DO NOT operate without entire Grass Catcher or guard

in place. Grass Catcher components are subject to

deterioration during normal use. Inspect frequently and

replace worn or damaged components immediately.

Installing the Grass Bag Adapter

(Optional Accessory on Some Models)

WARNING

Amputation Hazard

• DO NOT attempt any maintenance, adjustments or

service with engine and blade running.

• STOP engine and blade.

• Disconnect spark plug wire and secure away from spark

plug.

Burn Hazard

• Engine and components are HOT.

• Avoid serious burns, allow sufficient time for all

components to cool.

1. Remove the mulching cover. See Removing the

Mulching Cover .

2. Install the adapter (A, Figure 12) to the deck in place of

the mulching cover, making sure that:

• The front hole (B) on the outside front of the adapter

fits over the stud where the front of the mulching

cover was originally secured;

• The slot (C) on top of the adapter slips under the

restraining nut on top of the deck (under the right

front corner of the engine);

• The slot (D) on the rear of the adapter slips onto the

stud behind the rear of the discharge opening, where

the rear of the mulching cover was originally secured.

3. Install the internal/external tooth lock washers and knob

nuts onto the studs and tighten securely.

4. Route the recoil rope around the outside of the rope guide

pulley (E).

Note:The recoil rope may need to be slackened. See

Starting the Mower .

Not for

Reproduction

13

12

Installing the Mulching Plug

(Optional Accessory on Some Models)

WARNING

Amputation Hazard

• DO NOT attempt any maintenance, adjustments or

service with engine and blade running.

• STOP engine and blade.

• Disconnect spark plug wire and secure away from spark

plug.

Burn Hazard

• Engine and components are HOT.

• Avoid serious burns, allow sufficient time for all

components to cool.

1. Install the mulching plug (A, Figure 13) if mulching is

desired after the bag adapter is installed. Install the

mulching plug completely and securely into the bag

adapter (B).

2. Install the grass bag as a safeguard and to further secure

the mulching plug.

WARNING

Thrown Objects Hazard

Install the grass bag when using the mulching plug. Failure

to do so may result in personal injury or death.

3. See Mulching Operation .

13

Installing the Grass Bag

(Optional Accessory on Some Models)

WARNING

Amputation Hazard

• DO NOT attempt any maintenance, adjustments or

service with engine and blade running.

• STOP engine and blade.

• Disconnect spark plug wire and secure away from spark

plug.

Burn Hazard

• Engine and components are HOT.

• Avoid serious burns, allow sufficient time for all

components to cool.

1. Install the grass bag adapter. See Installing the Grass

Bag Adapter .

2. Install the grass bag by sliding the connector (A, Figure

14) over the adapter flange.

3. Attach the grass bag hooks (B) over the middle handle

cross bar.

Not for

Reproduction

14 www.snapper.com

14

WARNING

Unsafe Operation Hazard

Grass Catcher bags are made of woven fabric, and are

subject to deterioration and wear during normal usage.

Check condition of bag before each use. Immediately

replace worn or damaged catcher bags with only genuine

replacement bags. The grass catcher is optional equipment

on some models.

Charging the Battery

(Optional Accessory on Some Models)

The battery provided with your mower is sealed and

maintenance-free. It requires no special care other than

keeping it properly charged. Use only the charger provided

with your mower when charging the battery.

Charge the battery after each use, and if the battery has been

stored for longer than 30 days. The time required to charge

the battery varies, but typically 16 to 24 hours will be sufficient

to bring the battery to a fully charged condition.

1. Remove the dust cap from the charger jack (A, Figure

15).

2. Plug the battery charger (B) into the charger jack.

3. Plug the charger into a 120-volt wall outlet.

4. Charge the battery for a period of 16 to 24 hours. (Longer

periods will not damage the battery.)

5. Unplug the charger from the wall outlet.

6. Unplug the charger from the charger jack.

7. Replace the dust cap onto the charger jack.

15

WARNING

Explosion Hazard

Avoid Serious Injury and Property Damage.

• DO NOT attempt to charge this battery with automotive

or ‘Boost’ chargers.

• DO NOT attempt to jump start a mower that has a dead

battery.

• Always use the charger supplied with this mower to

charge this battery.

Maintenance

Emissions Control Service

Maintenance, replacement, or repair of the emissions

control devices and systems may be performed by

any off-road engine repair establishment or individual.

However, to obtain "no charge" emissions control service, the

work must be performed by a factory authorized dealer. See

the Emissions Control Statements.

Not for

Reproduction

15

Maintenance Chart

WARNING

Amputation Hazard

• DO NOT attempt any maintenance, adjustments or

service with engine and blade running.

• STOP engine and blade.

• Disconnect spark plug wire and secure away from spark

plug.

Burn Hazard

• Engine and components are HOT.

• Avoid serious burns, allow sufficient time for all

components to cool.

Laceration Hazard

• Wear heavy leather gloves when handling or working

around cutting blades.

• Blades are extremely sharp and can cause severe

injury.

MOWER

Every 8 Hours or Daily

Check safety interlock system

Clean debris off mower

Every 25 Hours or Annually *

Check mower for loose hardware

See Dealer Annually to

Lubricate mower

Check mower blade **

Check mower blade stopping time

Check drive belt

Clean battery and cables

* Whichever comes first

** Check blade more often in regions with sandy soils or high

dust conditions

ENGINE

First 5 Hours

Change engine oil

Every 8 Hours or Daily

Check engine oil level

Every 25 Hours or Annually *

Clean engine air filter and pre-cleaner (if equipped) **

Every 50 Hours or Annually *

Change engine oil

Replace oil filter (if equipped)

Annually

Replace air filter

Replace pre-cleaner (if equipped)

See Dealer Annually to

Inspect muffler and spark arrester (if equipped)

Replace spark plug

Replace fuel filter (if equipped)

ENGINE

Clean engine air cooling system

* Whichever comes first

** Clean more often in dusty conditions or when airborne

debris is present

Change Engine Oil

WARNING

Amputation Hazard

• DO NOT attempt any maintenance, adjustments or

service with engine and blade running.

• STOP engine and blade.

• Disconnect spark plug wire and secure away from spark

plug.

Burn Hazard

• Engine and components are HOT.

• Avoid serious burns, allow sufficient time for all

components to cool.

Laceration Hazard

• Wear heavy leather gloves when handling or working

around cutting blades.

• Blades are extremely sharp and can cause severe

injury.

1. Drain the fuel tank completely.

2. Remove the dipstick (A, Figure 16), then turn the mower

on its side. Allow the oil to drain from the oil fill tube into

an appropriate container. Dispose of used oil properly.

3. Place the mower upright, then fill the engine with engine

oil to the ‘full’ mark on the dipstick. Refer to the section

entitled ‘Oil Recommendations’. Do not overfill.

16

Not for

Reproduction

16 www.snapper.com

NOTICE

Drain the fuel tank before tipping the machine. DO NOT

tip the machine with the carburetor or spark plug down. Oil

from the crankcase will saturate the air filter and cause the

engine to be hard to start or not start at all. If contamination

does occur, the air filter will have to be replaced.

Change Oil Filter

(If Equipped)

1. Drain the oil from the engine. See Change Engine Oil .

2. Remove the oil filter (B, Figure 16) and dispose of

properly.

3. Before you install the new oil filter, lightly lubricate the oil

filter gasket with fresh, clean oil.

4. Install the oil filter by hand until the gasket contacts the oil

filter adapter, then tighten the oil filter 1/2 to 3/4 turns.

5. Add oil. See Change Engine Oil .

6. Start and run the engine. As the engine warms up, check

for oil leaks.

7. Stop the engine and check the oil level. It should be at the

top of the full indicator on the dipstick.

Service Air Filter

WARNING

Fire Hazard

Never start or run the engine with the air cleaner assembly

(if equipped) or the air filter (if equipped) removed.

NOTICE

Do not use pressurized air or solvents to clean the filter.

Pressurized air can damage the filter and solvents will

dissolve the filter.

1. Remove the fastener (A, Figure 17) and the air filter cover

(B).

2. Remove the pre-cleaner (C) and the filter (D).

3. To loosen debris, gently tap the filter on a hard surface. If

the filter is excessively dirty, replace with a new filter.

4. Wash the pre-cleaner in liquid detergent and water. Then

allow it to thoroughly air dry. Do not oil the pre-cleaner.

5. Assemble the dry pre-cleaner to the filter.

6. Install the filter and pre-cleaner into the base (E). Make

sure filter fits securely in the base.

7. Install air filter cover and secure with fastener. Make sure

the fastener is tight.

17

Service Air Filter

See Figure: 18, 19

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or death.

• Never start and run the engine with the air cleaner

assembly (if equipped) or the air filter (if equipped)

removed.

NOTICE Do not use pressurized air or solvents to clean

the filter. Pressurized air can damage the filter and solvents

will dissolve the filter.

See the Maintenance Schedule for service requirements.

Various models use either a foam or a paper filter. Some

models may also have an optional pre-cleaner that can be

washed and reused. Compare the illustrations in this manual

with the type installed on your engine and service as follows.

Foam Air Filter

1. Open the fastener(s) (A, Figure 18).

Not for

Reproduction

17

18

2. Remove the cover (B, Figure 18).

3. To prevent debris from falling into the carburetor, carefully

remove the foam element (C, Figure 18) from the air filter

base.

4. Wash the foam element (C, Figure 18) in liquid detergent

and water. Squeeze dry the foam element in a clean

cloth.

5. Saturate the foam element (C, Figure 18) with clean

engine oil. To remove the excess engine oil, squeeze the

foam element in a clean cloth.

6. Install the foam element (C, Figure 18) onto the air filter

base.

7. Install the cover (B, Figure 18) and secure with

fastener(s) (A).

Paper Air Filter

1. Loosen the fastener(s) (A, Figure19).

19

2. Remove the cover (B, Figure19).

3. To prevent debris from falling into the carburetor, carefully

remove the pre-cleaner (D, Figure19) and the filter (C)

from the air filter base.

4. Remove the pre-cleaner (D, Figure19), if equipped, from

the filter (C).

5. To loosen debris, gently tap the filter (C, Figure19) on a

hard surface. If the filter is excessively dirty, replace with

a new filter.

6. Wash the pre-cleaner (D, Figure19), if equipped, in liquid

detergent and water. Allow the pre-cleaner to thoroughly

air dry.Do notoil the pre-cleaner.

7. Assemble the dry pre-cleaner (D, Figure19), if equipped,

to the filter (C).

8. Install the filter (C, Figure19) and the pre-cleaner (D), if

equipped, onto the air filter base. Make sure the filter fits

securely on the air filter base.

9. Install the cover (B, Figure19) and secure with the

fastener(s) (A). Make sure the fastener(s) is tight.

Check Safety Interlock System

1. Start the mower.

2. Release the blade control. The engine must stop within 3

seconds.

WARNING

Unsafe Operation Hazard

If the engine does not stop within 3 seconds, do not use the

mower. Bring the mower to an authorized dealer for service.

Not for

Reproduction

18 www.snapper.com

Clean Debris Off Mower

WARNING

Amputation Hazard

• DO NOT attempt any maintenance, adjustments or

service with engine and blade running.

• STOP engine and blade.

• Disconnect spark plug wire and secure away from spark

plug.

Burn Hazard

• Engine and components are HOT.

• Avoid serious burns, allow sufficient time for all

components to cool.

Laceration Hazard

• Wear heavy leather gloves when handling or working

around cutting blades.

• Blades are extremely sharp and can cause severe

injury.

1. Clean dirt and debris from the top of the mower deck.

2. Clean any debris buildup on or around the engine, etc.

While cleaning, check components for wear or damage.

Replace worn or damaged components immediately.

Storage Procedure

WARNING

Amputation Hazard

• DO NOT attempt any maintenance, adjustments or

service with engine and blade running.

• STOP engine and blade.

• Remove battery (if equipped).

Burn Hazard

• Engine and components are HOT.

• Avoid serious burns, allow sufficient time for all

components to cool.

Laceration Hazard

• Wear heavy leather gloves when handling or working

around cutting blades.

• Blades are extremely sharp and can cause severe

injury.

Prepare the mower for end-of-season storage as follows:

1. Disconnect the spark plug wire and secure away from the

spark plug.

2. Drain the fuel tank and let the engine run until all fuel is

out of the carburetor.

Note:If using a fuel stabilizer, there is no need to drain the

fuel tank. SeeStorage-Fuel System.

3. Use a brush or compressed air to remove loose debris,

then use a damp cloth to wipe down the unit.

4. Tilt the mower up on its rear wheels and inspect the

underside of the deck. (Do not tilt the mower with the

spark plug or carburetor down.) Scrape away stubborn

accumulation of grass with a putty knife and/or wire

brush.

5. Lubricate all exposed metal with a light coating of oil to

prevent corrosion.

6. Carefully fold the handles, flexing the control cables to

prevent cable damage.

7. Store the mower in a shed or other dry area, protected

from weather.

NOTICE Do not stand unit on end.

Storage - Fuel System

Fuel can become stale when kept in a storage container for

more than 30 days. Each time you fill the container with fuel,

addSTA-BIL 360°

®

PROTECTION™to the fuel as specified

by the manufacturer’s instructions. This keeps fuel fresh and

decreases fuel-related problems or contamination in the fuel

system.

It is not necessary to drain fuel from the engine whenSTA-

BIL 360°

®

PROTECTION™is added as instructed. Before

storage, turn the engine ON for 2 minutes to move the fuel

and stabilizer through the fuel system.

Service

WARNING

Amputation Hazard

• DO NOT attempt any maintenance, adjustments or

service with engine and blade running.

• STOP engine and blade.

• Disconnect spark plug wire and secure away from spark

plug.

Burn Hazard

• Engine and components are HOT.

• Avoid serious burns, allow sufficient time for all

components to cool.

Laceration Hazard

• Wear heavy leather gloves when handling or working

around cutting blades.

• Blades are extremely sharp and can cause severe

injury.

Check Grease Level in Transmission

1. Remove the transmission fill plug (A, Figure 20). Roll the

machine forward or backward while looking down into the

plug hole.

2. If liquid grease is not visible on the input gear (the small

gear below the plug hole), add an amount, to cover the

gear, of Snapper “00” grease.

Note:Snapper “00” grease (Part No. 7029443) is available at

your dealer.

Note:Do not spill grease or oil onto the surface of the drive

disc (A, Figure 21).

Not for

Reproduction

19

3. Reinstall the transmission plug.

4. Check the grease level after each 25 hours of operation.

20

21

Check Mower Blade

1. Disconnect the spark plug wire and secure the end away

from the plug.

2. Tilt the mower up on its rear wheels for access to the

blade cap screw (A, Figure 22). Do not tilt the mower with

the spark plug or carburetor down.

NOTICE

Drain the fuel tank before tipping the mower. DO NOT tip

the machine with the carburetor or spark plug down. Oil

from the crankcase will saturate the air filter and cause the

engine to be hard to start or not start at all. If contamination

does occur, the air filter will have to be replaced.

3. Check the torque of the blade cap screw. Recommended

torque: 40 lb-ft (54 Nm).

4. Check the blade for sharpness, wear and damage. See

Blade Wear Limits .

22

Check Engine Drive Belt

• Visually check the engine drive belt for cracking, fraying,

severed or exposed belt strands. If worn or damaged,

replace the belt before operating the mower.

Check Transmission Drive Belt

• Visually check the poly-v belt for cracking, fraying,

severed or exposed belt strands. If worn or damaged,

replace the belt before operating the mower.

Mower Blade Replacement

WARNING

Amputation Hazard

• DO NOT attempt any maintenance, adjustments or

service with engine and blade running.

• STOP engine and blade.

• Disconnect spark plug wire and secure away from spark

plug.

Burn Hazard

• Engine and components are HOT.

• Avoid serious burns, allow sufficient time for all

components to cool.

Laceration Hazard

• Wear heavy leather gloves when handling or working

around cutting blades.

• Blades are extremely sharp and can cause severe

injury.

WARNING

Unsafe Operation Hazard

Not for

Reproduction

20 www.snapper.com

DO NOT use a cutting blade that shows signs of excessive

wear or damage.

Standard Blade Wear Limit

1. Inspect the blade (Figure 23) frequently for signs of

excessive wear or damage:

• (A) New blade

• (B) Wear limit (notch starts)

• (C) Dangerous condition! Do not use on the mower!

Replace with a new blade.

23

Ninja Blade Wear Limit

1. Inspect the blade (Figure 24) frequently for signs of

excessive wear or damage:

• (A) New blade

• (B) Wear limit (cracks or notches begin to appear on

tip)

• (C) Dangerous condition! Do not use on the mower!

Replace with a new blade.

24

Blade Sharpening

1. Disconnect the spark plug wire and secure the end away

from the plug.

2. Tilt the mower up on its rear wheels. Do not tilt the mower

with the spark plug or carburetor down.

NOTICE

Drain the fuel tank before tipping the mower. DO NOT tip

the machine with the carburetor or spark plug down. Oil

from the crankcase will saturate the air filter and cause the

engine to be hard to start or not start at all. If contamination

does occur, the air filter will have to be replaced.

3. Remove the blade (B, Figure 25).

4. Sharpen the blade on a grinding wheel at an angle of 22

to 28 degrees (B, Figure 26). DO NOT sharpen the blade

beyond the original cutting edge (A).

5. Check blade for balance. If necessary, correct balance by

grinding heavy end of blade.

6. Reinstall blade (B, Figure 25). Note the correct assembly

order:

• (A) Blade hub

• (B) Blade

• (C) Blade flange (facing up)

• (D) Cone washer (concave side up)

• (E) Capscrew

7. Check torque of blade retaining cap screw.

Recommended torque: 40 lb-ft (54 Nm).

Not for

Reproduction

La page charge ...

Snapper 7800980 Manuel utilisateur

Snapper 7800980 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents