Installation Instructions
Notice d’installation
9001 597 251 (0103)
*9001597251*
To avoid possible injury or property damage, OBSERVE
ALL WARNINGS AND CAUTIONS.
installers only. The dishwasher must be installed by a
• In addition to these instructions, the dishwasher
shall be installed to meet all electrical and plumb-
ing codes and ordinances (both national and local).
Read these installation instructions completely and
follow them carefully. They will save you time and ef-
fort and help to ensure safety and optimum dishwasher
performance.
IMPORTANT
• The dishwasher drain hose must be installed with
a
portion of it at least 3384 cm
-
erly.
• This dishwasher is intended for indoor residential
use only, and should not be used in commercial
food service establishments.
• NEW INSTALLATION - If the dishwasher is a new
installation, most of the work must be done before
the dishwasher is moved into place.
• REPLACEMENT - If the dishwasher is replacing
another dishwasher, check the existing dishwasher
connections for compatibility with the new
dishwasher, and replace parts as necessary.
• This appliance has been found to be in compliance
with CAN/CSA-C22.2 No. 167/UL 749. It is the
responsibility of the owner and the installer to
determine if additional requirements and standards
• Not for outdoor use.
Important Safety Instructions
3
Inspect the Dishwasher
After unpacking the dishwasher and prior to installation,
thoroughly inspect the dishwasher for possible freight
or cosmetic damage. Report any damage immediately.
Cosmetic defects must be reported within 30 days of
installation.
NOTE: Do not discard any bags or items that come with the
original package until after the entire installation has been
completed.
Please READ and SAVE this information
4
Avoiding General Hazards
Do not use the dishwasher until it is completely
installed. When opening the door on an uninstalled
dishwasher, carefully open the door while supporting
the rear of the unit. Failure to follow this warning can
cause the dishwasher to tip over and result in serious
injury.
Before installing the “L”-shaped supplied countertop
mounting brackets (select models), decide which
method will be used to secure the dishwasher into its
opening. Once these mounting brackets are installed
damage the mounting brackets and the dishwasher.
In some conditions, hydrogen gas can form in a hot
water system that has not been used for weeks.
Hydrogen gas is explosive.
in a well ventilated area until there is no sound or evi-
dence of gas.
Temperatures required for soldering and sweating will
damage the dishwasher’s base and water inlet valve.
If plumbing lines are to be soldered or sweated, keep
the heat source at least 6
(152.4 mm) away from the
dishwasher’s base and water inlet valve.
Removing any cover or pulling the dishwasher from the
cabinet can expose hot water connections, electrical
power and sharp edges or points. Handle with care.
Avoiding Electrical Shock/Fire Hazards
Do not allow the electrical and water supply lines to
touch. Separate channels are provided under the
dishwasher.
Do not work on an energized circuit. Doing so could
-
cians should perform electrical work. Do not attempt
any work on the dishwasher electric supply circuit
until you are certain the circuit is de-energized.
Make sure electrical work is properly installed. There
should be no loose electrical connections. Ensure all
electrical connections are properly made.
The customer has the responsibility of ensuring that
the dishwasher electrical installation is in compliance
with all national and local electrical codes and
ordinances. The dishwasher is designed for an
electrical supply
of 120V, 60 Hz, AC, connected
to a dishwasher-dedicated, properly grounded
electrical circuit with a fuse or breaker rated for 15
OR 20amps. Electrical supply conductors shall be a
minimum #14 AWG copper only wire rated at 75°C
(167°F) or higher.
This appliance must be connected to a grounded
metal, permanent wiring system, or an equipment-
grounding conductor must be run with the circuit
conductors and connected to the equipment-
grounding terminal or lead on the appliance. Do not
use extension cords.
Avoiding Plumbing/Scalding Hazards
Do not perform any work on a charged hot water
plumbers should perform plumbing work. Do
not attempt any work on the dishwasher hot water
supply plumbing
Do not over tighten the 90° elbow. Doing so
may damage the water inlet valve and cause a water
leak.
Temperatures required for soldering and sweating
will damage the dishwasher’s water inlet valve. If
plumbing lines are to be soldered or sweated,
keep the heat source at least 6 (152.4 mm) away
from the dishwasher’s water inlet valve.
Check local plumbing codes for approved
plumbing procedures and accessories. All plumbing
should be done in accordance with national and local
codes.
These instructions depict an installation method
for stainless steel braided hose or PEX hot water
supply lines. If using copper tubing or other
material for water supply, defer to a licensed
plumber for proper installation.
WARNING
4
STATE OF CALIFORNIA PROPOSITION 65 WARNING:
WARNING
Cancer and Reprodutive Harm - www.P65Warnings.ca.gov
Proposition 65 Warning:
This product may contain a chemical known to the State of
California, which can cause cancer or reproductive harm.
Therefore, the packaging of your product may bear the following
label as required by California:
5
Hot Water Supply Line - Minimum
3
/8 O.D. copper tubing or metal
braided dishwasher supply line
Hammer Hole Saw
Pipe Wrench
Tape Measure
Slot Screwdriver
Torx T-20 Screwdriver
Wire Cutter
Wire Stripper
Ø 2 mm (
1
/16 in) Drill
Level
Adjustable Wrench
Tools and Materials Needed
5
6
A
B
F
G
I
H
J
K
L
C
E
D
A
Extra Tall Item Sprinkler *
B
Toe Panel Screws
C
Mounting Brackets
D
Mounting Bracket Screws
E
Toe Panel (2 pieces)
F
Toe Panel caps and screws (select models only)
G
Screw Clamp (for hose)
H
Water Supply Adaptor Fitting
I
Flexible Edge Protector Grommet for electrical wire
J
Rubber Drain Hose Adaptor
K Toe Panel Mounting Brackets (select models only)
L Outer toe panel (3rd piece) (select models only)
M Side Mount Force Distributor (Alternate Side Mount only)
N Mounting Bracket Screws (Alternate Side Mount only)
O Installation Guide for Fully Integrated Door Panel (select
models only)
P Power Cord
Q Wrench (wrench size 13)
Materials Supplied
O
P
Q
Ø 4x15 mm
Ø 4x13 mm
Ø 4x17 mm
Installation Guide for
Fully Integrated Door Panel
6
M
N
ø 4x28
* Depending on the model
of your dishwasher.
Also available from
Customer Service.
7
After locating the proper place for your new dishwasher,
you will need to create any required openings to allow for
passage of the water, drain and electrical line. In order to
avoid interference with the dishwasher when sliding it into the
cabinet, place your openings within the dimensions shown
in Figure 3 below.
Check clearance
between
dishwasher door
and wall
Countertop
17
¹¹
/
- 18
(450 - 458 mm)
Required Openings:
1 1/2" (38 mm) diameter- To pass the included electrical
supply junction box through to adjacent cabinet. The edges
of the opening should, if the partition is wood, be smooth
and rounded or, if the partition is metal, be covered with the
grommet (I) provided for this purpose by the manufacturer.
Note: If the incoming electric supply, water supply and drain
connections are all in the same cabinet, the one 4
3
/4″ x 2
3
/8″
(120 x 60 mm) hole will be large enough for all three to pass
through.
(100 x 50 mm) - To pass the included water supply line
toward the water supply
1
1
/4(32 mm) diameter - To pass the dishwasher drain hose
toward the drain connection
Before sliding the dishwasher into the cabinet, remove the
hose clip at the back of the dishwasher as shown in Figure
4. The hose clip may be used later to hold the drain hose as
shown in Figure 7.
Figure 2
Enclosure Requirements
NOTE: This dishwasher is designed to be enclosed on the
top and both sides by standard residential kitchen cabinetry.
Select a location as close to the sink as possible for easy
access to water supply and drain lines.
For proper dishwasher operation and appearance, ensure
that the enclosure is square and has the dimensions shown
in Figure 1 below.
NOTE: If your dishwasher opening width measures
>18 (458mm) use the TOP mounting method.
If your dishwasher opening width measures 18(458mm)
use the SIDE MOUNT mounting method.
If the dishwasher is to be installed in a corner, make sure that
there is adequate clearance to open the door. See Figure
2 below.
WARNING
Avoid Scalding or Electrical Shock Hazard!
Make sure the water supply and electrical supply
are shut o before installation or service.
Avoid Electrical Shock/Fire Hazard
Do not allow the electrical and water supply lines
to touch.
WARNING
90°
22
5
/
8
(575 mm)
32-34¼(813-870 mm)
Figure 1
Figure 3
4
1
/2"
(114mm)
2
1
/2"
(64mm)
7
Figure 4
8
Electrical Preparation
WARNING
Dishwasher Electrical Rating
Volts Hertz Amperes Watts
120 60 12 1,440
(max)
Electrical Supply
The customer has the responsibility of ensuring that the dish-
washer electrical installation is
in compliance with all national
and
local electrical
codes and
ordinances.
The dishwasher
is
designed for an electrical supply of 120V, 60 Hz, AC, connect-
ed to a dishwasher-dedicated, properly grounded electrical cir-
cuit with a fuse or breaker rated for 15 or 20 amps.
Grounding Instructions
This appliance must be grounded. In the event of a
malfunction or breakdown, grounding will reduce the risk of
electric shock by providing a path of least resistance for
electric current. This appliance is equipped with a cord
having an equipment-grounding conductor and a grounding
plug. The plug must be plugged into an appropriate outlet
that is installed and grounded in accordance with all local
codes and ordinances.
Make sure that the dishwasher is connected to a suitable
ground in compliance with all local codes or, in the absence
of a local code, with the NATIONAL ELECTRICAL CODE in
the United States or the CANADIAN ELECTRIC CODE
C22.1-latest edition in Canada as well as any provincial/state
or municipal or local codes that apply.
Note: Installations requiring hard wiring and terminal
block - The accessory terminal block/junction box model,
SMZPCJB1UC, designed for permanent wire connection, is
not included but can be ordered through Customer Service by
calling 1-800-944-2904. Follow the instructions included with
the kit.
Note: Only use the included power cord. If cord is missing
order kit SMZPC002UC through Customer Service.
Figure 5
Avoid Electrical Shock Hazard!
Do not work on an energized circuit. Doing so could
should perform electrical work. Do not attempt any work
on the dishwasher electric supply circuit until you are
certain the circuit is de-energized.
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. Check with
a qualified electrician or serviceman if you are in doubt as
to whether the appliance is properly grounded.
DO NOT modify the plug provided with the appliance; if it
will not fit the outlet, have a proper outlet installed by a
qualified electrician.
To avoid possible injury or property damage, care should
be exercised when the dishwasher is installed or removed
to reduce the likelihood of damage to the power cord.
Avoid Fire Hazard!
Make sure electrical work is properly installed and
Make sure there are no loose electrical connections. Make
sure all electrical connections are properly made.
Loose and improperly installed electrical connections
can result in overheating!
Wall Socket Connections:
Only use the provided power cord for wall socket
connections.
DO NOT
cord or adapter with this appliance.
DO NOT cut or splice the power cord.
DO NOT alter the power cord in any way.
Permanent Wire Connections (in addition to the
warnings above):
Only use the junction box power cord, sold as Accessory
kit #SMZPCJB1UC.
Carefully review the terminal block installation instructions.
DO NOT remove, alter or bypass the terminal block.
8
Strap
Al
te
rn
at
e
c
a
b
l
e rout
i
ng
• Plug the end of the supply cord into the back of the
dishwasher. Be sure it goes through the strap on either
the right or left side of the dishwasher.
• The outlet for the power supply cord should be located in
a cabinet or wall adjacent to the dishwasher cabinet.
• Do not plug dishwasher in until all the steps of installation
are complete.
9
Hot Water Supply
The hot water heater should be set to deliver approximately
120° F (49° C) water to the dishwasher. Water that is too
water temperatures will increase run times. The hot water
supply pressure must be between 15 - 145 psi (1 - 10 bar).
IMPORTANT NOTES:
sure to make all solder connections before connecting the
water supply line to the dishwasher.
· Make sure there are no sharp bends or kinks in the water
· Always use the appropriate seal when making plumbing
connections.
· Before connecting the water supply line to the dishwasher,
to clear any foreign material.
· Turn on the water supply and check for leaks after
connections are made.
Water Supply Shut O Valve
the hot water supply line, as shown in Figure 9. All solder
connections must be made before the water line is connected
to the dishwasher.
Temperatures required for soldering and sweating
will damage the dishwasher. If plumbing lines
are to be soldered or sweated, keep the heat
source at least 6 inches (152.4 mm) away from
the dishwasher.
Avoid Scald Hazard!
Do not perform any work on a charged hot water
line. Serious injury could result. Only qualied
plumbers should perform plumbing work. Do not
attempt any work on the dishwasher hot water
supply plumbing until you are certain the hot water
supply is shut o.
WARNING
Inlet Water Connections
9
Connecting the Hot Water Supply
There are two plastic corrugated hoses that exit the back of
end, is the water supply hose to the dishwasher (the other
3
/
4
(76 x 45 mm) opening through the cabinet to pass the dish-
To connect the hot water supply:
parts bag onto the dishwasher water supply hose. This
2. Pass the dishwasher water supply line with attached
valve. Take care not to allow the hose to kink or twist
behind the dishwasher.
3. Connect the dishwasher water supply line with adaptor to
this connection. Always use the appropriate seal when
making plumbing connections.
NOTE: The end of the dishwasher water inlet hose is
heavy and will need to be supported. It is best to lay the
end on the cabinet oor as shown in Figure 6.
4. After all connections are made, turn on the hot water and
check for leaks.
Figure 6
10
The dishwasher drain hose may be connected to the house-
a 1¼" diameter hole in order to pass the drain hose through
the cabinet.
1 Directly under the sink dishwasher drain connection, as
shown in Figure 8.
2 Directly to a disposer dishwasher drain connection, as
shown in Figure 9.
3 To the under sink dishwasher drain connection through
an air gap, as shown in Figure 10.
4 To a disposer dishwasher drain connection through an air
gap, as shown on Figure 11.
IMPORTANT NOTES:
· If local ordinance require an air gap, install it according
to the manufacturer’s instructions.
· If the dishwasher drain hose is to be connected to a
disposer dishwasher drain connection, remove the plug
from the disposer’s dishwasher drain connection.
· The dishwasher drain hose must have one place along
· The drain hose length can be extended if necessary. The
maximum length of the drain hose, including the hose
Figure 10 Figure 11
Figure 8
Figure 7
Non-Metallic Tie
MIN.
20"
MIN.
20"
Non-Metallic Tie
Figure 9
Remove
plug
Drain Connections
max 43” (1100mm)
G
G
G
G
min 20 (508mm)
max 43 (1100mm)
min 20 (508mm)
max 43 (1100mm)
10
11
For a large port, use the drain hose as it is.
1. For a small port, insert the rubber drain hose adaptor
into the drain hose end.
2. Obtain the Rubber Drain Hose Adaptor (J) spring
clamp from the Dishwasher Installation Kit (do not
substitute).
3. Insert the dishwasher drain hose into the end of the
drain hose (see Figure 12. Be sure to fully insert the
drain hose.
4. Use the clamp provided to attach the Rubber Drain Hose
Adaptor to the house plumbing as shown in Figure 13.
The dishwasher can be secured into its enclosure in 2 ways:
NOTE: If your dishwasher opening width measures >18″
(458
mm) use the TOP MOUNT mounting methods. If your
dishwasher opening width measures 18″ (458 mm) use
the SIDE MOUNT mounting method.
Figure 13
Figure 12
Before installing the supplied countertop mounting
brackets, decide which method of securing the
dishwasher into its enclosure will be used. Once the
mounting brackets are installed on the dishwasher,
removing them is difficult and will damage the
mounting brackets and the dishwasher.
Installation of Mounting Brackets
Installation of Rubber Drain Hose Adaptor
J
G
Top Mount is used for countertops made of wood or other
materials that can be easily drilled, or for openings
wider than 18". Orient the mounting brackets as shown
in Figure 14 and position the two small tabs on the
mounting brackets over the two slots on the
dishwasher’s front corners. Push the mounting brackets
down firmly to insert the tabs into the slots.
Side Mount is for countertops made of marble,
granite, or other very hard materials that cannot be
easily drilled. Also, it is for for openings that are 18".
Insert a side mount force distributor (M) in each side
as shown in Figure 15.
11
Figure 14
Top Mount
C
Torx T 20
Figure 15
Side Mount
M
12
Center the dishwasher in the opening before securing it to
your cabinet or countertop as shown in Figure 17. Remove
the top cutlery rack as shown in Figure 18 *.
LEVELING THE DISHWASHER
SECURING THE DISHWASHER
Avoid Tip Over Hazard!
Do not use the dishwasher until it is completely
installed. When opening the door on an uninstalled
dishwasher, carefully open the door while
supporting the rear of the unit. Failure to follow
this warning can result in serious injury.
WARNING
Figure 16
Figure 17
The unit should now be ready to slide into the cabinet
opening. To avoid scratching the oor, use oor protection
and caution when sliding the dishwasher into the cabinet.
Make sure that the hoses and cords do not bunch up behind
the unit or kink as you slide the unit back. Make certain
to slide the unit into place before raising the leg levelers.
Level the dishwasher horizontally by turning feet clockwise
to raise or counter-clockwise to lower front of the unit.
Level the dishwasher vertically by turning center screw to
raise or lower the back.
Drive the mounting screws through the holes in the mounting
brackets as shown for Top Mount (Figure 19), Side
Mount (Figure 20).
Figure 19
For Top Mount
12
* Depending on whether the dishwasher includes a
top cutlery rack.
Figure 18 *
Figure 20
For Side Mount
1
/16
D
~½" (13 mm)
(2 mm)
Torx T 20
Torx T 20
N
13
Your dishwasher comes with either a two-piece or three-
piece toe panel (model dependent) to allow height adjust-
ment.
1. Position the slotted rear toe panel (part of E) on the
2. Position the mating front toe panel (part of E) on top of
the rear toe panel allowing the angled edge to rest on
the mating edge of the dishwasher.
3.
4.
Drive the two black screws (B) through the holes in the
toe panel to secure. Use the supplied screws to avoid
damaging the dishwasher. See Figure 2
1
For models with outer toe panel (3rd piece - L) slide the
brackets (K) provided, into the slots of the toe panel you
just attached.
6. Once you determine the correct position for the brackets,
remove the bracket and bend the metal tab. See Figure
22. This ensures that the toe panel will not slide in further
than you need.
7. Re-insert the brackets.
8. Attach the outer toe panel (L) onto the brackets and drive
the screws provided (F) in place to secure the toe panel.
Figure 22
Attaching the Toe Panel
B
B
E
K
F
L
K
13
Figure 21
14
Your dishwasher requires no special care other than
that described in the Care and Maintenance section of
the Use and Care Manual. If you are having a problem
with your dishwasher, before calling for service please
refer to the Self Help section in the Use and Care
Manual. If service is necessary, contact your dealer or
installer or an authorized service center.
Do not attempt to repair the appliance yourself. Any
work performed by unauthorized personnel may void
the warranty. If you are having a problem with your
dishwasher and are not pleased with the service you
have received, please take the following steps (in the
order listed below) until the problem is corrected to
your satisfaction:
1. Contact your installer or the Authorized Service
Contractor in your area.
2. E-mail us. See your Use and Care Manual for
instructions.
3. Write us at the address below:
BSH Home Appliances, Corp.
1901 Main Street, Suite 600
Irvine, CA 92614
4. Call us at the Customer Service phone number :
1-800-944-2904
Please be sure to include (if you are writing), or have
available (if you are calling), the following information:
• Model number
• Serial number
• Date of original purchase
• Date the problem originated
• Explanation of the problem
• Daytime phone number where you can be reached.
Please make a copy of your invoice and keep it with this
manual. The customer must show proof of purchase to
obtain warranty service.
Customer Service
14
-
AVERTISSEMENTS ET PRÉCAUTIONS.
• Outre ces instructions, l’installation du lave-linge
et ordonnances nationaux et locaux en matière
Lire cette notice d’installation entièrement et s’y
conformer scrupuleusement. Cette notice vous
-
male de votre lave-vaisselle.
IMPORTANT
• Le tuyau de vidange du lave-vaisselle doit être in-
33
pouces (84 cm) minimum au-dessus du plancher
ne pas se vidanger correctement.
•
-
-
ciaux.
• NOUVELLE INSTALLATION - Si le lave-vaisselle
que l’appareil ne soit mis en place.
• REMPLACEMENT - Si le lave-vaisselle est
raccordements du lave-vaisselle existant pour vous
lave-vaisselle, et remplacer les pièces qui doivent
l’être.
Consignes de sécurité importantes
Veuillez LIRE et CONSERVER ces informations
15
18
Prévention des dangers d’ordre général
Ne pas utiliser le lave-vaisselle tant que l’installation n’est
prudence et en soutenant la partie arrière de l’appareil.
Le non respect de cet avertissement peut entraîner le
basculement du lave-vaisselle et provoquer de graves
blessures.
ainsi que le lave-vaisselle.
semaines. L’hydrogène est un gaz explosif.
Avant de remplir un lave-vaisselle en utilisant de l’eau
-
(152,4 mm) minimum de distance de la base et du robinet
Le retrait d’une paroi ou le fait de tirer le lave-vaisselle
hors de son encastrement peut exposer les conduites
prudence.
Prévention des dangers de choc
électrique et d’incendie
ne doivent pas entrer en contact les uns avec les autres.
lave-vaisselle.
Ne pas tenter d’intervenir sur un circuit sous tension.
Vous risquez autrement des blessures graves, voire la
moins d’être certain que celui-ci est hors tension.
-
-ible
ou disjoncteur d’une puissance de 15 ou 20 ampères. Les
-
pas utiliser de rallonge.
Prévention des dangers d’ébouillantage
et liés aux travaux de plomberie
Ne pas tenter de travailler sur une conduite d’eau chaude
la tuyauterie. Ne pas tenter d’intervenir sur la tuyauterie
d’alimentation d’eau chaude du lave-vaisselle tant que
vous n’êtes pas certain que l’alimentation d’eau chaude est
de provoquer une fuite.
d’eau du lave-vaisselle. Si certains tuyaux doivent être
6 pouces (152,4 mm) minimum de distance du robinet
Consulter les codes de plomberie locaux pour connaître les
-
ment aux codes nationaux et locaux.
WARNING
AVERTISSEMENT
16
Tuyau d’alimentation d’eau chaude - tube de cuivre de
3
/8 po
d’eau chaude ((tube de cuivre/raccord de compression, ou
Marteau Scie cylindrique
Ø 2 mm (
1
/16 in)
Perceuse
Outils et pièces nécessaires
16
lame plate
Tournevis T-20
Pince
coupante
-
nuder
Inspection du lave-vaisselle
REMARQUE : ne pas jeter les sacs ou les éléments
contenus dans l’emballage d’origine avant d’avoir
complètement terminé l’installation du lave-vaisselle.
17
Avertissement issue de la proposition 65 de l’État de la
Californie :
Ce produit pourrait contenir un produit chimique reconnu par
l’État de la Californie comme cancérigène ou ayant des effets
nocifs sur la reproduc-tion. Par conséquent, l’emballage de
votre produit pourrait porter l’étiquette suivante, comme requis
par la Californie :
20
A
B
F
G
I
H
J
K
L
C
E
D
A
Gicleur pour grands articles *
B
Vis pour panneau de plinthe
C
D
E
Panneau de plinthe (2 pièces)
F
Couvercles pour panneau de plinthe (certains modèles unique-
ment)
G
H
Raccord d’adaptateur d’alimentation d’eau
I
J
Adaptateur de tuyau de vidange en caoutchouc
K
uniquement)
L
uniquement)
M
alternatif uniquement)
N
O
P Cordon d’alimentation
Q
Matériel fourni
M
N
O
P
Q
Ø 4x15 mm
Ø 4x13 mm
Ø 4x17 mm
Guide d’installation pour un panneau
18
ø 4x28
* Selon le modèle de votre
lave-vaisselle. Également
disponible auprès du service
client.
Exigences d’encastrement
REMARQUE : ce lave-vaisselle est conçu pour être encastré sous
un comptoir et entre deux armoires adjacentes standard d’une
cuisine résidentielle.
-
Figure 1 ci-dessous.
REMARQUE : si la largeur de l’ouverture de votre lave-
vaisselle est supérieure à >18 po (458mm) utilisez
les méthodes de MONTAGE PAR LE
DESSUS. ISi la
largeur de l’ouverture de votre lave-vaisselle est
inférieure à 18 po (458mm) utilisez la méthode de
MON-TAGE LATÉRAL.
porte. Voir la Figure 2 ci-dessous.
lors de l’installation du lave-vaisselle dans l’armoire, disposer
Figure 3 ci-dessous.
Vérier le
dégagement
entre la porte du
lave-vaisselle
et le mur
Plan de travail
WARNING
Évitez les brûlures ou les risques de secousse électrique !
S’assurer que l’alimentation d’eau et l’alimentation électrique
sont mises à l’arrêt avant toute installation ou réparation.
Évitez les risques de décharge électrique et
d’incendie. Les câbles électriques et les tuyaux
d’alimentation d’eau ne doivent pas entrer en con-
tact les uns avec les autres.
WARNING
90°
22
5
/
8
(575mm)
32-34¼(813-870mm)
18
Figure 1
Figure 2
Figure 3
Ouvertures requises :
1 1/2" (38 mm) diameter- Passage du boîtier de les
conduites d’alimentation à travers une armoire adjacente. •
Si l’ouverture est percée dans du bois, poncer les rebords
du trou. Si l’ouverture est percée dans du métal, couvercle
avec la gaine de protection flexible pour fil électrique (I).
REMARQUE : si les raccordements d’arrivée d’électricité,
d’alimentation d’eau et de vidange se trouvent tous dans la
même armoire, une ouverture de 4
3
/4″ x 2
3
/8″ (120 x 60mm) est
su isante pour recevoir les trois.
(100 x 50mm) - Passage du tuyau d’alimentation d’eau
compris vers l’alimentation d’eau
1
1
/4(32mm) diameter - Passage du tuyau de vidange du lave-
vaisselle vers le raccordement de vidange
Avant d’encastrer le lave-vaisselle dans l’armoire, retirer le
-
Figure 4 -
(Figure 7).
Figure 4
4
1
/
2
"
(114mm)
2
1
/
2
"
(64mm)
AVERTISSEMENT
AVERTISSEMENT
19
17
¹¹
/
- 18
(450 - 458 mm)
22
Préparation de l’installation électrique
20
Évitez les risques de décharge électrique!
Ne pas tenter d’intervenir sur un circuit sous tension.
Vous risquez autrement des blessures graves, voire la
moins d’être certain que celui-ci est hors tension.
d’endommager le cordon d’alimentation.
Une mauvaise connexion du conducteur de mise à la
terre de l'équipement peut entraîner un risque
d'électrocution. Vérifiez auprès d'un électricien ou d'un
technicien qualifié si vous n'êtes pas sûr que l'appareil
soit correctement mis à la terre.
NE modifiez PAS la fiche fournie avec l'appareil; si elle
ne rentre pas dans la prise, faites installer une prise
appropriée par un électricien qualifié.
Évitez les risques d’incendie!
sont bien faits.
Des raccordements électriques desserrés ou mal
installés peuvent entraîner une surchaue!
risques d’incendie.
Prises murales :
Uniquement le câble d’alimentation fourni pour brancher
l’appareil dans une prise murale.
N’attachez pas de câble d’extension, un autre type de
ÉVITEZ de fendre ou de trancher le câble d’alimentation.
quelconque.
Connexions filaires permanentes (en plus des
Utilisez uniquement le câble d’alimentation de la boîte
de jonction, vendue en tant que trousse d’accessoire
#SMZPCJBIUC.
Lisez attentivement les instructions d’installation du
bornier.
WARNING
AVERTISSEMENT
Caractéristiques électriques du lave-vaisselle
Alimentation électrique
Le -
-
-
vaisselle, avec protection par fusible ou disjoncteur d’une puis-
sance de 15-20 ampères.
Instructions de mise à la terre
Cet appareil doit être mis à la terre. En cas de
dysfonctionnement ou de panne, la mise à la terre réduira le
risque de choc électrique en fournissant un chemin de
moindre résistance au courant électrique. Cet appareil est
équipé d'un cordon avec un conducteur de mise à la terre de
l'équipement et une fiche de mise à la terre. La fiche doit
être branchée dans une prise appropriée qui est installée et
mise à la terre conformément à tous les codes et règlements
locaux.
code local, au CODE NATIONAL D’ÉLECTRICITÉ aux États-
Unis ou au CODE D’ÉLECTRICITÉ DU CANADA, C22.1,
Remarque
: Installations utilisant ilaires permanentes
Le modèle de bornier accessoire / boîte de jonction,
clientèle en composant le 1-800-944-2904.
Suivez les instructions fournies avec le kit.
Volts Hertz Amperes Watts
120 60 15
1,450
(max)
12
1,440
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
dans d''autres langues
- English: Yes SPE53B52UC Installation guide
Autres documents
-
Bosch SPE68U55UC Guide d'installation
-
-
Gaggenau DF 480 700F Guide d'installation
-
-
Bosch SHE4AEM6N Manuel utilisateur
-
-
Bosch SHV4AEB3N Manuel utilisateur
-
Summit DW186NTADA Le manuel du propriétaire