Horizon Fitness 7.4AT Le manuel du propriétaire

Marque: Horizon Fitness

Modèle: 7.4AT

Taper: Le manuel du propriétaire

Ce manuel convient également à

7.4ATIX

TREADMILL OWNER’S MANUAL

MANUEL DU PROPRIÉTAIRE DU TAPIS ROULANT

MANUAL DEL PROPIETARIO DE LA CAMINADORA

Read the TREADMILL GUIDE before using this OWNER’S MANUAL.

Lire le GUIDE D’UTILISATION DU TAPIS ROULANT avant de se référer au présent MANUEL DU PROPRIÉTAIRE.

Lea la GUÍA DE LA CAMINADORA antes de utilizar este MANUAL DEL PROPIETARIO.

3 ENGLISH

33 FRANÇAIS

63 ESPAÑOL

IMPORTANT PRECAUTIONS

SAVE THESE INSTRUCTIONS

When using an electrical product, basic precautions should always be followed, including the following: Read all instructions before

using this treadmill. It is the responsibility of the owner to ensure that all users of this treadmill are adequately informed of all warnings

and precautions. If you have any questions after reading this guide, contact Customer Tech Support at the number listed on the back

panel of the OWNER’S MANUAL.

This treadmill is intended for in-home use only. Do not use this treadmill in any commercial, rental, school or institutional setting.

Failureto comply will void the warranty.

TO REDUCE THE RISK OF BURNS, FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS:

• Never use the treadmill before securing the safety tether clip to your clothing.

• If you experience any kind of pain, including but not limited to chest pains, nausea, dizziness, or shortness of breath, stop exercising

immediately and consult your physician before continuing.

• When exercising, always maintain a comfortable pace.

• Do not wear clothes that might catch on any part of the treadmill.

• Always wear athletic shoes while using this equipment.

• Do not jump on the treadmill.

• At no time should more than one person be on treadmill while in operation.

• This treadmill should not be used by persons weighing more than specified in the OWNER’S MANUAL WARRANTY SECTION. Failure

tocomply will void the warranty.

• When lowering the treadmill deck, wait until rear feet are firmly on the floor before stepping on the deck.

• Disconnect all power before servicing or moving the equipment. To clean, wipe surfaces down with soap and slightly damp cloth only;

never use solvents. (See MAINTENANCE)

• The treadmill should never be left unattended when plugged in. Unplug from outlet when not in use, and before putting on or taking

offparts.

• Do not operate under blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury to persons.

• Connect this exercise product to a properly grounded outlet only.

WARNING

TO REDUCE THE RISK OF ELECTRICAL SHOCK:

Always unplug the treadmill from the electrical outlet immediately after using, before cleaning, performing maintenance and putting on or

taking off parts.

DANGER

TO REDUCE THE RISK OF BURNS, FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS:

• At NO time should pets or children under the age of 13 be closer to the treadmill than 10 feet.

• At NO time should children under the age of 13 use the treadmill.

• Children over the age of 13 or disabled persons should not use the treadmill without adult supervision.

• Use the treadmill only for its intended use as described in the treadmill guide and owner’s manual.

• Do not use other attachments that are not recommended by the manufacturer. Attachments may cause injury.

• Never operate the treadmill if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged,

orimmersed in water. Return the treadmill to a service center for examination and repair.

• Keep power cord away from heated surfaces. Do not carry this unit by its supply cord or use the cord as a handle.

• Never operate the treadmill with the air opening blocked. Keep the air opening clean, free of lint, hair, and the like.

• To prevent electrical shock, never drop or insert any object into any opening.

• Do not operate where aerosol (spray) products are being used or when oxygen is being administered.

• To disconnect, turn all controls to the off position, then remove plug from outlet.

• Do not use treadmill in any location that is not temperature controlled, such as but not limited to garages, porches, pool rooms,

bathrooms, car ports or outdoors. Failure to comply will void the warranty.

• This treadmill is intended for in-home use only. Do not use this treadmill in any commercial, rental, school or institutional setting.

Failureto comply will void the warranty.

• Do not remove the console covers unless instructed by Customer Tech Support. Service should only be done by an authorized service

atechnician.

It is essential that your treadmill is used only indoors, in a climate controlled room. If your treadmill has been exposed to colder

temperatures or high moisture climates, it is strongly recommended that the treadmill is warmed up to room temperature before first

time use. Failure to do so may cause premature electronic failure.

WARNING

GROUNDING INSTRUCTIONS

This product must be grounded. If a treadmill should malfunction or breakdown, grounding provides a path of least resistance for electrical

current to reduce the risk of electrical shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding

plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with local codes and

ordinances.

Connect this exercise product to a properly grounded outlet only.

Never operate product with a damaged cord or plug even if it is working properly.

Never operate any product if it appears damaged, or has been immersed in water.

Contact Customer Tech Support for replacement or repair.

3-POLE

GROUNDED

OUTLET

GROUNDING PIN

WARNING

DANGER

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or

service provider if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product.

If it will not fit the outlet, have a proper outlet installed by a qualified electrician.

This product is for use on a nominal 110-120 Volt circuit and has a grounding plug that looks like the plug in the illustration. Make sure

thatthe product is connected to an outlet having the same configuration as the plug. No adapter should be used with this product.

This product must be used on a dedicated circuit. To determine if you are on a dedicated circuit, shut off the power to that circuit and

observe if any other devices lose power. If so, move devices to a different circuit. Note: There are usually multiple outlets on one circuit.

Thistreadmill should be used with a minimum 15-amp circuit.

ASSEMBLY

There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly

instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the treadmill

could have parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to the treadmill, the

assembly instructions must be reviewed and corrective actions should be taken.

Before proceeding, find your treadmill’s serial number located on a white barcode sticker near

the on/off power switch and power cord and enter it in the space provided below.

ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOXES BELOW:

» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.

SERIAL NUMBER:

WARNING

SERIAL NUMBER LOCATION

MODEL NAME: HORIZON 7.4AT TREADMILL

SPEAKERS

CONSOLE FAN

WATER BOTTLE HOLDER

PULSE RATE GRIPS

ON/OFF SWITCH

POWER CORD

RUNNING BELT/RUNNING DECK

TRANSPORT WHEEL

FOOT LOCK LATCH DECAL

(UNDERNEATH FOOT LATCH)

TABLET/READING RACK

CONTROL PANEL AND DISPLAY WINDOWS

CONSOLE

SAFETY KEY PLACEMENT

CROSS SUPPORT BAR

CONSOLE MAST

FOOT LATCH (UNDERNEATH DECK)

MOTOR COVER

SIDE RAIL

ROLLER END CAP

REAR ROLLER

TENSION/ALIGNMENT BOLTS

TOOLS INCLUDED:

F 8 mm T-Wrench

F 6 mm L-Wrench

F 5 mm L-Wrench

PARTS INCLUDED:

F 1 Main Frame

F 1 Console Assembly

F 2 Console Masts

F 1 Cross Support Bar

F 1 Hardware Kit

F 1 Safety Key

F 1 Audio Adapter Cable

F 1 Bottle of Silicone Lubricant

(for 2 applications)

F 1 Power Cord

F 2 Pulse Rate Grips

If you have questions or if there

are any missing parts, contact

Customer Tech Support. Contact

information is located on the

back panel of this manual.

DO NOT ATTEMPT TO LIFT THE TREADMILL! Do not move or lift treadmill from

packaging until specified to do so in the assembly instructions. You may remove the

plastic wrap from console masts.

WARNING

UNPACKING

Place the treadmill carton on a level flat surface. It is recommended that you place a

protective covering on your floor. Take CAUTION when handling and transporting this unit.

Never open box when it is on its side. Once the banding straps have been removed, do not

lift or transport this unit unless it is fully assembled and in the upright folded position, with

the lock latch secure. Unpack and assemble the unit where it will be used. The enclosed

treadmill is equipped with high-pressure shocks and may spring open if mishandled. Never

grab hold of any portion of the incline frame and attempt to lift or move the treadmill.

FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!

WARNING

NEED HELP?

NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and partially

threaded in before completely tightening any ONE bolt.

NOTE: A light application of grease may aid in the installation of hardware. Any grease, such

as lithium bike grease is recommended.

PRE ASSEMBLY

ASSEMBLY STEP 1

A Cut the yellow banding straps and lift the running

deck upward from the rear to remove all contents from

underneath the running deck.

B Open HARDWARE FOR STEP 1.

C Insert UPRIGHT GUIDE BOLT (A) into MAIN FRAME

BRACKET (1) and fully tighten.

D Attach LEAD WIRE to bottom end of CONSOLE

CABLE (2). Pull LEAD WIRE through RIGHT

CONSOLE MAST (4). After pulling the wire through

the mast, the top of the CONSOLE CABLE (2) should

be located at the ATTACHMENT BRACKET (7).

E Attach RIGHT CONSOLE MAST (4) to MAIN

FRAME(3) using 4 BOLTS (B), 4 FLAT WASHERS (C)

AND 4SPRING WASHERS (D). Feed the extra console

cable back into the upright mast.

F Repeat STEP E on the LEFT SIDE.

M8X1.25PX11L 2 A UPRIGHT GUIDE BOLT

NOTE: Do not fully tighten the following bolts until the

end of STEP 4.

HARDWARE FOR STEP 1

PART TYPE DESCRIPTION QTY

M8X1.25PX80L 8B MAST BOLT

8.2X15.4X2.0T

SPRING WASHER

8.4X15.5X1.6T

FLAT WASHER

NOTE: Be careful not to pinch the console cable

while attaching the right console mast.

ASSEMBLY STEP 2

NOTE: Do not fully tighten bolts until STEP

M6X1.0PX15L 4 E BOLT

HARDWARE FOR STEP 2

PART TYPE DESCRIPTION QTY

A Open HARDWARE FOR STEP 2.

B Attach CROSS SUPPORT BAR (5) using holes on

UPRIGHT MASTS (4) with 4 BOLTS (E).

A Open HARDWARE FOR STEP 3.

B Have someone help hold the console while attaching

the CONSOLE CABLE (2). Use the lead wire to

carefully pull the CONSOLE CABLE (2) out of the

RIGHT CONSOLE MAST (4). Attach the CONSOLE

CABLE (2) from the CONSOLE (6) to the CONSOLE

CABLE (2) from the top of the RIGHT UPRIGHT MAST

(4). Detach and discard the lead wire.

C Carefully slide the CONSOLE (6) onto the

ATTACHMENT BRACKETS (7) being careful not to

pinch the CONSOLE CABLE (2). Align the holes on the

bottom side of the CONSOLE (6) with the holes on the

ATTACHMENT BRACKETS (7).

D Attach the CONSOLE (6) to the ATTACHMENT

BRACKETS (7) by first placing ARC WASHERS (F)

onto BOLTS (G) AND (H) as illustrated. Insert SHORT

BOLTS (G) into the top hole of the ATTACHMENT

BRACKET (7) and LONG BOLTS (H) into the bottom

hole.

E Repeat STEP D for the opposite side.

ASSEMBLY STEP 3

F G H

HARDWARE FOR STEP 3

PART TYPE DESCRIPTION QTY

8.4X15.5X1.6T

M8x1.25Px15L

M8x1.25Px70L

ARC WASHER

LONG BOLT

SHORT BOLT

ASSEMBLY STEP 4

A Open HARDWARE FOR STEP 4.

B Attach RIGHT SIDE PULSE RATE GRIP (8)

tothe underside of the CONSOLE (6) using

4 BOLTS (I), 4 SPRING WASHERS (J) and

4 FLAT WASHERS (K).

C Connect the RIGHT CONSOLE CABLES (9R)

andcarefully tuck in wires to avoid damage.

D Repeat STEP B on the LEFT SIDE.

E Connect the LEFT CONSOLE CABLES (9L)

andcarefully tuck wires to avoid damage.

HARDWARE FOR STEP 4

PART TYPE DESCRIPTION QTY

M8x15L 8I BOLT

8.2X15.4X2.0T 8J SPRING WASHER

8.4X15.5X1.6T 8K FLAT WASHER

I J K

NOTE: Fully tighten all bolts from PREVIOUS STEPS

ASSEMBLY COMPLETE!

Before the first use, lubricate the treadmill deck by

following the instructions in the MAINTENANCE

section in the TREADMILL GUIDE.

TREADMILL OPERATION

This section explains how to use your treadmill’s console and programming.

The BASIC OPERATION section in the TREADMILL GUIDE has instructions for the following:

• LOCATION OF THE TREADMILL

• USING THE SAFETY KEY

• FOLDING THE TREADMILL

• MOVING THE TREADMILL

• LEVELING THE TREADMILL

• TENSIONING THE RUNNING BELT

• CENTERING THE RUNNING BELT

• USING THE HEART RATE FUNCTION

LT T

CONSOLE OPERATION

Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use.

A) LCD DISPLAY WINDOWS: Watts, Pace, Calories/Hour, Heart Rate, Laps.

B) LED DISPLAY: Time, Speed, Distance, Incline, Pace, Heart Rate, and Calories.

C) WORKOUT LED INDICATORS: indicates what workout is set for the current program.

D) SELECT TARGET/WORKOUT KNOB: rotate/press to select your desired workout/target

E) START: press to begin exercising, start your workout, or resume exercising after pause.

F) STOP: press to pause/end your workout. Hold for 3 seconds to reset the console.

G) INCLINE SCROLL WHEEL: used to adjust incline in small increments (.5%).

H) SPEED SCROLL WHEEL: used to adjust speed in small increments (.1 MPH).

I) INCLINE QUICK KEYS: used to reach desired incline more quickly.

J) SPEED QUICK KEYS: used to reach desired speed more quickly.

K) FAN KEY: press to turn fan on and off.

L) FAN: personal workout fan.

M) SPEAKERS: music plays through speakers when your CD / MP3 player is connected to the console.

N) AUDIO IN JACK: plug your CD / MP3 player into the console using the included audio adaptor cable.

O) AUDIO OUT / HEADPHONE JACK: plug your headphones into this jack to listen to your music through the headphones.

Note: when headphones are plugged into the headphone jack the sound will no longer come out throughthe speakers.

P) USB INPUT: 1A/5V USB output power.

Q) WATER BOTTLE POCKETS: holds personal workout equipment.

R) TABLET/READING RACK: holds tablet or reading material.

S) BLUETOOTH INDICTOR LIGHT: displays when machine is paired with a Bluetooth compatible device.

T) INTERVAL KEYS: these are programmable keys. When an user is selected, they can be programmed to a desired

speed and incline setting.

DISPLAY WINDOWS

• TIME: Shown as minutes : seconds. View the time remaining or the time elapsed in your workout.

• DISTANCE: Shown as miles. Indicates distance traveled during your workout.

• SPEED: Shown as MPH. Indicates how fast your walking or running surface is moving.

• INCLINE: Shown as percent. Indicates the incline of your walking or running surface.

• CALORIES: Total calories burned during your workout.

• HEART RATE: Shown as BPM (beats per minute). Used to monitor your heart rate (displayed when contact is made

with both pulse grips).

• PACE: Indicates how many minutes it takes to complete a mile while running or walking at your current speed.

• WATTS: Indicates the power output at your current speed and incline.

• CALORIES/ HOUR: Indicates the number of calories you will burn in an hour at your current speed and incline

• BRICKYARD: Each vertical segment represents a speed or incline unit, each horizontal segment represents time.

• LAPS: Shows how many 400 meter (¼ mile) laps have been completed.

• COUNT (SPRINT 8): Shows how many Sprint 8 program sprints you have completed

GETTING STARTED

1) Check to make sure no objects are placed on the belt that will hinder the movement of the treadmill.

2) Plug in the power cord and turn the treadmill ON. (The ON/OFF switch is next to the power cord.)

3) Stand on the side rails of the treadmill.

4) Attach the safety key clip to part of your clothing making sure that it is secure and will not become detached during operation.

5) Insert the safety key into the safety keyhole in the console.

6) You have two options to start your workout:

A) QUICK START UP

Simply press the START key to begin working out.

Time, distance, and calories will all count up from zero. OR...

B) SELECT A WORKOUT OR TARGET

1) Select your USER by turning the workout knob and then pressing when your desired USER is displayed.

2) Select your WEIGHT by turning the workout knob and then pressing when your desired WEIGHT is displayed.

3) Select your PROGRAM by turning the workout knob and then pressing when your desired PROGRAM is displayed.

4) Adjust the SETTING by turning the workout knob and then pressing when your desired SETTING is displayed.

5) Press START to begin.

HOW TO PROGRAM AND USE CUSTOM INTERVAL BUTTONS

The programmable interval buttons located on the pulse rate grips are designed to help you customize this machine to match whatever

workout you like to do the most.

The LEFT and RIGHT INTERVAL BUTTONS are programmable for speed and incline.

To program the INTERVAL button, you must select a user, start the machine, set the desired speed and incline, press and hold the

desired INTERVAL button for three seconds until the treadmill beeps. Now the INTERVAL button is programmed to your settings. After

programming the INTERVAL button, it will remember the setting for that user until reprogrammed.

Now when the INTERVAL button is pressed, the treadmill speed and incline will change to the settings you programmed for that button.

The most common type of workout these keys will help with is interval training. We suggest programming one of the INTERVAL buttons to

your high intensity segments and the other to your recovery segments.

Another common use is to set one INTERVAL button to your warm up and cool down settings and the other to your desired workout

settings.

These buttons should allow you to customize the settings of your treadmill to quickly fit the type of workout you enjoy most.

INTERVAL BUTTON 1 INTERVAL BUTTON 2

SPEED SCROLL WHEEL

Roll forward/backward to increase/decrease speed

INCLINE SCROLL WHEEL

Roll forward/backward to increase/decrease incline.

La page charge ...

Horizon Fitness 7.4AT Le manuel du propriétaire

Marque: Horizon Fitness

Modèle: 7.4AT

Taper: Le manuel du propriétaire

Ce manuel convient également à

7.4ATIX

Télécharger le PDF

rapport

dans d''autres langues

English: Horizon Fitness 7.4AT Owner's manual
español: Horizon Fitness 7.4AT El manual del propietario

Horizon Fitness 7.4AT Le manuel du propriétaire

Ce manuel convient également à

Horizon Fitness 7.4AT Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents