Smooth Fitness 835 Manuel utilisateur

USER’S MANUAL

835 MOTORIZED TREADMILL

USER WEIGHT LIMITATION: 400lbs(181kgs).

SERIAL NUMBER (found on frame):

2 835i TREADMILL

PRECAUTIONS

For future service or related questions:

Please staple your receipt and/or write in the name and phone number of the retail store where you purchased your treadmill.

Name: ______________________________ Phone Number: ___________________ Receipt: ______________________

Precautions:

WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons, read the following important precautions

and information before operating the treadmill. It is the responsibility of the owner to ensure that all users of this treadmill are

adequately informed of all warnings and precautions.

• Use the treadmill only as described in this manual.

• Place on a level surface, with 6 feet 2 X1m

of clearance behind it. Do not place the treadmill on any surface that blocks air

openings. To protect the floor or carpet from damage, place a mat under the treadmill.

• When choosing a location for the treadmill be sure that the location and position permit access to a plug.

• Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a garage or covered patio, or near

water.

• Do not operate the treadmill where aerosol products are used or where oxygen is being administered.

• Keep children under the age of 12 and pets away from the treadmill at all times.

• The treadmill should not be used by persons weighing more than 400LBS (181 Kgs).

•

Never allow more than one person on the treadmill at a time. Wear appropriate exercise clothing when using the treadmill.

Do not wear loose clothing that could become caught in the treadmill. Athletic support clothes are recommended for both

men and women. Always wear athletic shoes. Never use the treadmill with bare feet, wearing only stockings, or in

sandals.

• When connecting the power cord, plug the power cord into a grounded circuit. No other appliance should be on the same

circuit.

• Always straddle the belt and allow it to start moving before stepping onto the belt.

• Always examine your treadmill before using to ensure all parts are in working order.

• Allow the belt to fully stop before dismounting.

• Never insert any object or body parts into any opening.

• Follow the safety information in regards to plugging in your treadmill.

• Keep the power cord away from the incline wheels and do not run the power cord underneath your treadmill. Do not

operate the treadmill with a damaged or frayed power cord.

• Always unplug the treadmill before cleaning and/or servicing. Service to your treadmill should only be performed by an

authorized service representative, unless authorized and/or instructed by the manufacturer. Failure to follow these

instructions will void the treadmill warranty.

• Never leave the treadmill unattended while it is running.

• Use “safety key” when operating the treadmill and make sure the “safety key” is clipped to the users clothing.

• Remove the “safety key” and store it in a safe place when the treadmill is not in use. Keep the “safety key” away from

children.

www.smoothfitness.com

3

PRECAUTIONS

Pour réparations futures ou questions connexes :

Please staple your receipt and/or write in the name and phone number of the retail store where you purchased your treadmill.

Name: ______________________________ Phone Number: ___________________ Receipt: ______________________

Précautions:

AVERTISSEMENT : Pour réduire les risques de brûlures, d’incendie, de choc électrique ou de blessures aux personnes, lire les

précautions importantes et l’information suivantes avant de se servir du tapis roulant. Il revient au propriétaire de s’assurer que tous

les utilisateurs de ce tapis ont bien été informés de tous les avertissements et précautions.

• Utiliser le tapis seulement comme il est décrit dans ce manuel.

• Le placer sur une surface plane, en laissant 2X1m d’espace libre en arrière. Ne pas placer le tapis roulant sur une surface

qui bloque les ouvertures d’air.

• Pour protéger le plancher ou un tapis de dommages, placer un petit tapis sous le tapis roulant.

• Choisir pour le tapis roulant un emplacement et une position qui permettent d’avoir accès à une prise murale.

• Garder le tapis roulant à l’intérieur, à un endroit sans humidité ni poussière. Ne pas mettre le tapis roulant dans un garage,

sur une terrasse couverte ou près de l’eau.

• Ne pas faire fonctionner le tapis roulant pendant la vaporisation de produits aérosol ou l’administration d’oxygène.

• Ne pas laisser les enfants de moins de 12 ans et les animaux s’approcher du tapis roulant.

• Le tapis roulant ne doit pas être utilisé par des personnes pesant plus de 160 kg (350 lb).

• Il ne doit jamais y avoir plus d’une personne sur le tapis à la fois. Porter des vêtements d’exercice appropriés pour utiliser

le tapis roulant. Ne pas porter de vêtements lâches qui pourraient être pris dans le tapis roulant. Les vêtements de soutien

athlétiques sont recommandés tant pour les hommes que pour les femmes. Porter toujours des chaussures d’athlétisme.

Ne pas être pieds nus, ou porter seulement des chaussettes ou des sandales lors de l’utilisation du tapis roulant.

• Brancher le cordon d’alimentation dans un circuit avec mise à la terre. Aucun autre appareil ne doit être sur le même

circuit.

• Toujours enjamber le tapis et le laisser commencer à rouler avant de monter dessus.

• Toujours examiner votre tapis roulant avant de l’utiliser pour s’assurer que toutes les pièces fonctionnent correctement.

• Laisser le tapis s’arrêter complètement avant de descendre.

• Ne jamais insérer d’objets ou de parties du corps dans une ouverture.

• Suivre les directives de sécurité en ce qui concerne le branchement de votre tapis roulant.

• Garder le cordon d’alimentation éloigné des roues inclinées et ne pas faire passer le cordon d’alimentation sous votre

tapis roulant. Ne pas faire fonctionner le tapis roulant si le cordon d’alimentation est endommagé ou effiloché.

• Débrancher toujours le tapis roulant avant de le nettoyer ou de le réparer.

• Toute réparation au tapis doit être effectuée par un réparateur agréé, à moins d’autorisation ou de directives contraires du

fabricant. Le non-respect de ces instructions annulera la garantie du tapis roulant.

• Ne jamais laisser le tapis roulant sans surveillance lorsque la clé de sécurité est insérée.

• Utiliser la « clé de sécurité » pour faire fonctionner le tapis roulant et s’assurer qu’elle est accrochée aux vêtements des

utilisateurs.

• Retirer la « clé de sécurité » et la ranger dans un endroit sûr lorsque le tapis roulant n’est pas en fonction. Garder la « clé

de sécurité » hors de la portée des enfants.

4 835i TREADMILL

POWER REQUIREMENTS

Power Requirements:

IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT IN THE RISK OF AN ELECTRIC

SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE MAN IF YOU ARE IN DOUBT AS TO WHETHER THE

PRODUCT IS PROPERLY GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE PRODUCT, IF IT WILL NOT FIT

THE OUTLET; HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN.

This treadmill can be seriously damaged by sudden voltage changes in your home’s electrical power. Voltage spikes, surges and

noise interference can result from weather conditions or from other appliances being turned on or off. To reduce the possibility of

treadmill damage, always use a surge protector (not included) with your treadmill.

Surge protectors can be purchased at most hardware stores. The manufacturer recommends a single outlet surge protector with a

UL 1449 rating as a Transient Voltage Surge Suppressor (TVSS) with a UL suppressed voltage rating of 400V or less and an

electrical rating 120VAC, 15 amps.

This treadmill must be grounded to reduce the risk of electrical shock. Grounding provides a path of least resistance for electric

current, should the treadmill malfunction. This treadmill is equipped with an electrical cord that has an equipment-grounding

conductor and a grounding plug. Always plug the power cord into a surge protector, and plug the surge protector into an

appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in the drawing

below.

GFCI outlets and GFCI / AFCI Circuit Breakers are NOT recommended for use on this product. GFCI outlets and GFCI / AFCI

Circuit Breakers may cause this equipment to function improperly.

www.smoothfitness.com

5

POWER REQUIREMENTS

Alimentation :

UN MAUVAIS BRANCHEMENT DU CONNECTEUR DE MISE À LA TERRE DE L’ÉQUIPEMENT POURRAIT PROVOQUER UN

CHOC ÉLECTRIQUE. EN CAS DE DOUTE, CONSULTER UN ÉLECTRICIEN OU UN RÉPARATEUR QUALIFIÉ POUR SAVOIR

SI LE PRODUIT EST CORRECTEMENT MIS À LA TERRE. NE PAS MODIFIER LA FICHE FOURNIE AVEC LE PRODUIT. SI

ELLE N’ENTRE PAS DANS LA PRISE, FAIRE INSTALLER UNE PRISE APPROPRIÉE PAR UN ÉLECTRICIEN

PROFESSIONNEL.

Ce tapis roulant pourrait être gravement endommagé en cas de changement soudain de tension dans votre alimentation électrique.

Les conditions météorologiques ou la mise sous tension ou hors tension d’autres appareils électriques peuvent provoquer des

pointes de tension, des surtensions ou un brouillage. Pour réduire la possibilité que le tapis soit endommagé, toujours utiliser un

limiteur de surtension (non inclus) avec votre tapis roulant.

Il est possible d’acheter des limiteurs de surtension dans la plupart des quincailleries. Le fabricant recommande un limiteur de

surtension UL 1449 à prise unique comme suppresseur de tension transitoire (TVSS) ayant un taux de suppression de tension de

400 V ou moins et une tension électrique de 110 V C.A., 15 A.

Ce tapis roulant doit être mis à la terre pour réduire le risque de choc électrique. La mise à la terre fournit une voie de moindre

résistance au courant électrique en cas de mauvais fonctionnement du tapis roulant. Ce tapis roulant est équipé d’un cordon

électrique avec un conducteur de mise à la terre et une fiche de mise à la terre. Brancher toujours le cordon électrique dans un

limiteur de surtension et brancher le limiteur de surtension dans une prise appropriée, correctement installée et mise à la terre

conformément à tous les codes locaux et ordonnances.

Ce produit doit être utilisé avec un circuit nominal de 110 volts et à une fiche de mise à la terre qui ressemble à celle illustrée ci-

dessous.

Les prises avec disjoncteur de fuite de terre et les disjoncteurs de fuite de terre ne sont PAS recommandés pour ce produit. Les

prises avec disjoncteur de fuite de terre et les disjoncteurs de fuite de terre pourraient provoquer un mauvais fonctionnement de cet

équipement.

6 835i TREADMILL

BEFORE YOU BEGIN

Open the boxes:

Open the boxes of your new equipment. Inventory all parts included in the boxes, and Supplied Hardware lists

on page 7 for a full count of the parts included. If you are missing any parts or have any questions contact us

directly at 888-800-1167

Gather your tools:

Before you begin, make sure that you have gathered all the necessary tools you may require to assemble the unit

properly. Having all of the necessary equipment at hand will save time and make the assembly quick and hassle-free.

Clear your work area:

Make sure that you have cleared away a large enough space to properly assemble the unit. Make sure the space is

free from anything that may cause injury during assembly. After the unit is fully assembled, make sure there is a

comfortable amount of free area around the unit for unobstructed operation.

Invite a friend:

Some of the assembly steps may require heavy lifting. It is recommended that you obtain the assistance of another

person when assembling this product.

User Weight Limitation:

Please note that there is a weight limitation for this product. If you weigh more than 350LBS (Approx. 160 Kgs). It is

not recommended that you use this product. Serious injury may occur if the user’s weight exceeds the limit shown

here. This product is not intended to support users whose weight exceeds this limit.

Care and maintenance:

The safety level can be maintained only if it is examined for damage and wear.

Replace any defective components immediately and stop all use of the equipment until repaired.

Always take care when mounting the equipment. Straddle the equipment by placing your feet on the straddle rails.

Dismount from the equipment only after all parts have stopped.

Always check the wear and tear components like pulley, belts, etc.…To prevent injury.

There is an emergency stop, in the form of a SAFETY KEY, to prevent injury; you can stop the treadmill immediately

by actuating the emergency stop for emergency dismount.

www.smoothfitness.com

7

SUPPLIED COMPONENTS / SUPPLIED HARDWARE

This list identifies the major components you will use to assemble this product.

No. Description Qty.

835i -101

Treadmill Base

1

835i -212

Console Assembly

1

835i -311

Left Upright

1

835i -310

Right Upright

1

835i -309

Left Base Cover

1

835i -305

Right Base cover

1

835i -302

Left Handle Bar

1

835i -301

Right Handle Bar

1

835i -306

M8x15mm Allen Head Bolt

18

835i -304

M8 Flat Washer

22

835i -308

M4x10mm Pan Head Screw

4

A

5mm Allen Key

1

B

6mm Allen Key

1

C

13mm Allen Wrench

1

D

Silicone Lubricant

1

835i -312

M8x100mm Bolt

2

835i -313

M8 Nut

2

835i -218

Safety Key

1

835i -145

Power Cord

1

Millimeters

101

302 301

311 310

212

309 305

304

312

308

306

B

C

A

313

D

218

145

8 835i TREADMILL

COMPLETE PARTS LIST

Item No. Description Qty.

835i -100

835i -101

Base Frame

1

835i -

102

Horizontal Adjustment 2

835i -

103

Front Mobile Wheel Cover 2

835i -104

Front Mobile Wheel

2

835i -

105

M4x10mm Bolt 4

835i -

106

M4x12mm Bolt 2

835i -107 Air Shock 1

835i -

108

M8x30mm Bolt 2

835i -

109

M8 Nut 3

835i -

110

Upper Locking Tube 1

835i -111

Lower Locking Tube

1

835i -

112

M8x55 mm Bolt 1

835i -

113

M8x50 mm Bolt 1

835i -114 Lift Arm 1

835i -

115

Hex. Screw 39mm 2

835i -

116

Washer, stud 4

835i -117

M8x15mm Bolt 4

835i -118

Hex. Screw 53mm 2

835i -

119

Incline Motor 1

835i -

120

M10x45mm Bolt 1

835i -121

M10x55mm Bolt 1

835i -

122

M10 Nut 2

835i -

123

Motor Control Board 1

835i -124

M4x10mm Bolt

4

835i -

125

Front Roller 1

835i -

126

Rear Roller 1

835i -127

M8x70mm Bolt 3

835i -128

M8x30mm Bolt 1

835i -

129

Running Deck Frame 1

835i -130

Rubber Cushion 8

835i -131

M6x15mm Bolt

10

835i -

132

Running Deck 1

835i -

133

Running Belt 1

835i -134

Driving Motor

1

835i -

135

Driving Belt 1

835i -

136

Lower Motor Cover 4

835i -137 M4x10mm Bolt 2

835i -

138

Rear Wheel 2

835i -

139

M8x60mm Bolt 2

835i -

140

Side Rail 2

www.smoothfitness.com

9

COMPLETE PARTS LIST

Item No. Description Qty.

835i -

141

Right End Cap 1

835i -142

Left End Cap 1

835i -143 M4x15mm Bolt 4

835i -144

Lower Console Wire 1

835i -145 Power Cord 1

835i -

146

Power Socket 1

835i -

147

M3x8mm Bolt 2

835i -

148

ON-OFF Switch 1

835i -149

Power Breaker 1

835i -150 Mudguard, motor control 1

835i -151

Mudguard, drive belt 1

835i -152

Running Deck Belly Pan 1

835i -

153

M4x10 mm Bolt 15

835i -

154

Adaptor 1

10 835i TREADMILL

Item No. Description Qty.

835i -200

835i -201

Console frame

1

835i -202 Hand pulse upper cover 2

835i -203

Hand pulse lower cover

2

835i -204

Bolt M3*20mm

4

835i -205

Hand pulse plate

4

835i -206

Upper console cover

1

835i -207

Console housing

1

835i -208

Panel, console

1

835i -209 Bolt M3*6mm 14

835i -210

Safety key base

1

835i -211

Fan

1

835i -212 Bolt M3*30mm 4

835i -213

Speaker

2

835i -214

Bolt M4*12mm

17

835i -215

IHP

1

835i -216

Bolt M2.6*8mm

2

835i -217

USB charger

1

835i -218

Bolt M2*6mm

6

835i -219 Tablet Shelf

1

835i -220

Audio jack

1

835i -221

Bolt M2*5mm

2

835i -222 Receiver 1

835i -223

Handle button wire

6

835i -224

Washer M4

4

835i -225

Screw location fixer

2

835i -226 Lower console cover 1

835i -227

Bolt M4*15mm

6

835i -228

Bolt M4*10mm

2

835i -229 Operational button 1

835i -230

Hand pulse wire

1

835i -231

Console wire

1

835i -232 Safety key 1

835i -233

Software update cap

1

835i -234

Right handle button cover

1

835i -235

Left handle button cover

1

835i -236

Handle button sticker

2

835i -237

Spring

2

835i -238

M4 washer

2

835i -239 Bolt M3*10mm 2

835i -240

Tablet left support

1

835i -241

Table right support

1

835i -242 Adaptor wire 1

www.smoothfitness.com

11

COMPLETE PARTS LIST

Item No. Description Qty.

835i -300

835i -301 Right handle bar 1

835i -302 Left handle bar 1

835i -303 Receiver 1

835i -304 M8 Flat Washer 22

835i -305 Right protective cover 1

835i -306 M8x15mm Bolt 18

835i -307 Upper motor cover 1

835i -308 M4x10mm Bolt 4

835i -309 Left Right protective cover 1

835i -310 Right Upright 1

835i -311 Left Upright 1

835i -312 M8x100mm Bolt 2

835i -313 M8 Nut 2

12 835i TREADMILL

PARTS DIAGRAM

MOST OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED

www.smoothfitness.com

13

PARTS DIAGRAM

MOST OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED.

14 835i TREADMILL

PARTS DIAGRAM

A MAJORITY OF THE PARTS SHOWN HERE HAVE BEEN PREASSEMBLED AT THE FACTORY.

www.smoothfitness.com

15

ASSEMBLY – PLEASE READ ALL STEPS BEFORE BEGINNING YOUR WORK.

STEP 1: Assemble the Upright

NOTE:

Make sure all wires are recessed into the frame. DO NOT trap or

pinch. DO NOT tighten bolts until STEP2.

When attaching the Right

upright (310) first attach the 8 pin data cable to the wire

in the upright. This will allow you to pull the data cable up through the upright after

installation.

(1) Slide the base frame covers over uprights.

(2) Attach the Left Upright (wrapped in clear plastic) and Right Upright (wrapped in

green shaded plastic) to the treadmill main frame, and secure using the

M8x15mm Allen Head Bolts (306) with M8 Flat Washers (304). HAND TIGHTEN

ONLY. Do not tighten the M8x15mm Allen Head Bolt (306) until STEP2 has

been completed.

306 X10

304 X10

Bolts should be hand tight only

Green plastic wrap

Clear plastic wrap

16 835i TREADMILL

ASSEMBLY

STEP 2: Attach the Handle Bars

(1). Take out right handle bar from carton, connect handle button wire (223).

(2). Attach the Right and Left Handle Bar and secure using the M8x15mm Allen

Head Bolt (306) with M8 Flat Washer (304).

306 X4

304 X4

Tighten all bolts and fasteners now

223

Speed

Incline

www.smoothfitness.com

17

ASSEMBLY

STEP 3: Attach the Console to Left and Right Uprights

(1) Connect Upper Console Wire (from console) and Lower Console Wire

(from Right Upright) as shown below (222 to 144). Connect the adaptor

wire (244 to 154).

(2) Place the console housing over the Left and Right Uprights and secure using

the 2 x M8x100mm Allen Head Bolt (312) with 2 x M8 Flat Washer (304)

Insert the bolt through the upper hole. Then attach the M8 Flat Washers (304)

and M8 Nut (313).

(3) Secure the lower bolt hole with the M8x15mm Allen Head Bolt (306) with

M8 Flat Washer (304).

TIGHTEN ALL BOLTS NOW

306 X4

304 X8

312

X2

313

X2

Caution Pinch point! Do not pinch wires between frame.

Tighten all bolts and fasteners now

18 835i TREADMILL

ASSEMBLY

STEP 4: Tighten the Lower Upright Bolt and attach Lower Protective Cover

(1) Fully tighten the M8x15mm Allen Head Bolt (308) to for STEP1.

(2) Attach the Left and Right Protective Cover, and secure using M4x10mm Pan

Head Screw (308).

308 X2

www.smoothfitness.com

19

ASSEMBLY

STEP 5:

Attach power cord (145) to front of base from in diagram below.

20 835i TREADMILL

ASSEMBLY

STEP 6:

Insert Safety Key (218) into Bottom Center of Console prior to operation. Your

treadmill will not Function with out the safety key.

La page charge ...

Smooth Fitness 835 Manuel utilisateur

Smooth Fitness 835 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents