Smooth Fitness 675iO/BT Manuel utilisateur

USER’S MANUAL

675iO/BT MOTORIZED TREADMILL

USER WEIGHT LIMITATION: 350lbs (159kgs).

SERIAL NUMBER (found on frame):

REV130228

2 675iO/BT TREADMILL

PRECAUTIONS

For future service or related questions:

Please staple your receipt and/or write in the name and phone number of the retail store where you purchased your treadmill.

Name: ______________________________ Phone Number: ___________________ Receipt: ______________________

Precautions:

WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons, read the following important precautions

and information before operating the treadmill. It is the responsibility of the owner to ensure that all users of this treadmill are

adequately informed of all warnings and precautions.

• Use the treadmill only as described in this manual.

• Place on a level surface, with 6 feet 2 X1m of clearance behind it. Do not place the treadmill on any surface that blocks air

openings. To protect the floor or carpet from damage, place a mat under the treadmill.

• When choosing a location for the treadmill be sure that the location and position permit access to a plug.

• Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a garage or covered patio, or near

water.

• Do not operate the treadmill where aerosol products are used or where oxygen is being administered.

• Keep children under the age of 12 and pets away from the treadmill at all times.

• The treadmill should not be used by persons weighing more than 350LBS (159 Kgs).

•

Never allow more than one person on the treadmill at a time. Wear appropriate exercise clothing when using the treadmill.

Do not wear loose clothing that could become caught in the treadmill. Athletic support clothes are recommended for both

men and women. Always wear athletic shoes. Never use the treadmill with bare feet, wearing only stockings, or in

sandals.

• When connecting the power cord, plug the power cord into a grounded circuit. No other appliance should be on the same

circuit.

• Always straddle the belt and allow it to start moving before stepping onto the belt.

• Always examine your treadmill before using to ensure all parts are in working order.

• Allow the belt to fully stop before dismounting.

• Never insert any object or body parts into any opening.

• Follow the safety information in regards to plugging in your treadmill.

• Keep the power cord away from the incline wheels and do not run the power cord underneath your treadmill. Do not

operate the treadmill with a damaged or frayed power cord.

• Always unplug the treadmill before cleaning and/or servicing. Service to your treadmill should only be performed by an

authorized service representative, unless authorized and/or instructed by the manufacturer. Failure to follow these

instructions will void the treadmill warranty.

• Never leave the treadmill unattended while it is running.

• Use “safety key” when operating the treadmill and make sure the “safety key” is clipped to the users clothing.

• Remove the “safety key” and store it in a safe place when the treadmill is not in use. Keep the “safety key” away from

children.

www.smoothfitness.com

3

PRECAUTIONS

Pour réparations futures ou questions connexes :

Please staple your receipt and/or write in the name and phone number of the retail store where you purchased your treadmill.

Name: ______________________________ Phone Number: ___________________ Receipt: ______________________

Précautions:

AVERTISSEMENT : Pour réduire les risques de brûlures, d’incendie, de choc électrique ou de blessures aux personnes, lire les

précautions importantes et l’information suivantes avant de se servir du tapis roulant. Il revient au propriétaire de s’assurer que tous

les utilisateurs de ce tapis ont bien été informés de tous les avertissements et précautions.

• Utiliser le tapis seulement comme il est décrit dans ce manuel.

• Le placer sur une surface plane, en laissant 2X1m d’espace libre en arrière. Ne pas placer le tapis roulant sur une surface

qui bloque les ouvertures d’air.

• Pour protéger le plancher ou un tapis de dommages, placer un petit tapis sous le tapis roulant.

• Choisir pour le tapis roulant un emplacement et une position qui permettent d’avoir accès à une prise murale.

• Garder le tapis roulant à l’intérieur, à un endroit sans humidité n

i poussière. Ne pas mettre le tapis roulant dans un garage,

sur une terrasse couverte ou près de l’eau.

• Ne pas faire fonctionner le tapis roulant pendant la vaporisation de produits aérosol ou l’administration d’oxygène.

• Ne pas laisser les enfants de moins de 12 ans et les animaux s’approcher du tapis roulant.

• Le tapis roulant ne doit pas être utilisé par des personnes pesant plus de 159 kg (350 lb).

• Il ne doit jamais y avoir plus d’une personne sur le tapis à la fois. Porter des vêtements d’exercice appropriés pour utiliser

le tapis roulant. Ne pas porter de vêtements lâches qui pourraient être pris dans le tapis roulant. Les vêtements de soutien

athlétiques sont recommandés tant pour les hommes que pour les femmes. Porter toujours des chaussures d’athlétisme.

Ne pas être pieds nus, ou porter seulement des chaussettes ou des sandales lors de l’utilisation du tapis roulant.

• Brancher le cordon d’alimentation dans un circuit avec mise à la terre. Aucun autre appareil ne doit être sur le même

circuit.

• Toujours enjamber le tapis et le laisser commencer à rouler avant de monter dessus.

• Toujours examiner votre tapis roulant avant de l’utiliser pour s’assurer que toutes les pièces fonctionnent correctement.

• Laisser le tapis s’arrêter complètement avant de descendre.

• Ne jamais insérer d’objets ou de parties du corps dans une ouverture.

• Suivre les directives de sécurité en ce qui concerne le branchement de votre tapis roulant.

• Garder le cordon d’alimentation éloigné des roues inclinées et ne pas faire passer le cordon d’alimentation sous votre

tapis roulant. Ne pas faire fonctionner le tapis roulant si le cordon d’alimentation est endommagé ou effiloché.

• Débrancher toujours le tapis roulant avant de le nettoyer ou de le réparer.

• Toute réparation au

tapis doit être effectuée par un réparateur agréé, à moins d’autorisation ou de directives contraires du

fabricant. Le non-respect de ces instructions annulera la garantie du tapis roulant.

• Ne jamais laisser le tapis roulant sans surveillance lorsque la clé de sécurité est insérée.

• Utiliser la « clé de sécurité » pour faire fonctionner le tapis roulant et s’assurer qu’elle est accrochée aux vêtements des

utilisateurs.

• Retirer la « clé de sécurité » et la ranger dans un endroit sûr lorsque le tapis roulant n’est pas en fonction. Garder la « clé

de sécurité » hors de la portée des enfants.

4 675iO/BT TREADMILL

POWER REQUIREMENTS

Power Requirements:

IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT IN THE RISK OF AN ELECTRIC

SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE MAN IF YOU ARE IN DOUBT AS TO WHETHER THE

PRODUCT IS PROPERLY GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE PRODUCT, IF IT WILL NOT FIT

THE OUTLET; HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN.

This treadmill can be seriously damaged by sudden voltage changes in your home’s electrical power. Voltage spikes, surges and

noise interference can result from weather conditions or from other appliances being turned on or off. To reduce the possibility of

treadmill damage, always use a surge protector (not included) with your treadmill.

Surge protectors can be purchased at most hardware stores. The manufacturer recommends a single outlet surge protector with a

UL 1449 rating as a Transient Voltage Surge Suppressor (TVSS) with a UL suppressed voltage rating of 400V or less and an

electrical rating 120VAC, 15 amps.

This treadmill must be grounded to reduce the risk of electrical shock. Grounding provides a path of least resistance for electric

current, should the treadmill malfunction. This treadmill is equipped with an electrical cord that has an equipment-grounding

conductor and a grounding plug. Always plug the power cord into a surge protector, and plug the surge protector into an

appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in the drawing

below.

GFCI outlets and GFCI / AFCI Circuit Breakers are NOT recommended for use on this product. GFCI outlets and GFCI / AFCI

Circuit Breakers may cause this equipment to function improperly.

www.smoothfitness.com

5

POWER REQUIREMENTS

Alimentation :

UN MAUVAIS BRANCHEMENT DU CONNECTEUR DE MISE À LA TERRE DE L’ÉQUIPEMENT POURRAIT PROVOQUER UN

CHOC ÉLECTRIQUE. EN CAS DE DOUTE, CONSULTER UN ÉLECTRICIEN OU UN RÉPARATEUR QUALIFIÉ POUR SAVOIR

SI LE PRODUIT EST CORRECTEMENT MIS À LA TERRE. NE PAS MODIFIER LA FICHE FOURNIE AVEC LE PRODUIT. SI

ELLE N’ENTRE PAS DANS LA PRISE, FAIRE INSTALLER UNE PRISE APPROPRIÉE PAR UN ÉLECTRICIEN

PROFESSIONNEL.

Ce tapis roulant pourrait être gravement endommagé en cas de changement soudain de tension dans votre alimentation électrique

.

Les conditions météorologiques ou la mise sous tension ou hors tension d’autres appareils électriques peuvent provoquer des

pointes de tension, des surtensions ou un brouillage. Pour réduire la possibilité que le tapis soit endommagé, toujours utiliser un

limiteur de surtension (non inclus) avec votre tapis roulant.

Il est possible d’acheter des limiteurs de surtension dans la plupart des quincailleries. Le fabricant recommande un limiteur de

surtension UL 1449 à prise unique comme suppresseur de tension transitoire (TVSS) ayant un taux de suppression de tension de

400 V ou moins et une tension électrique de 110 V C.A., 15 A.

Ce tapis roulant doit être mis à la terre pour réduire le risque de choc électrique. La mise à la terre fournit une voie de moindre

résistance au courant électrique en cas de mauvais fonctionnement du tapis roulant. Ce tapis roulant est équipé d’un cordon

électrique avec un conducteur de mise à la terre et une fiche de mise à la terre. Brancher toujours le cordon électrique dans un

limiteur de surtension et brancher le limiteur de surtension dans une prise appropriée, correctement installée et mise à la terre

conformément à tous les codes locaux et ordonnances.

Ce produit doit être utilisé avec un circuit nominal de 110 volts et à une fiche de mise à la terre qui ressemble à celle illustrée ci-

dessous.

Prises GFCI électriques et disjoncteurs GFCI / AFCI ne sont pas recommandées pour une utilisation sur ce

produit. Prises GFCI électriques et disjoncteurs GFCI / AFCI peut causer cet équipement de fonctionner correctement.

6 675iO/BT TREADMILL

BEFORE YOU BEGIN

Open the boxes:

Open the boxes of your new equipment. Inventory all parts included in the boxes and Supplied Hardware lists on

page 7 for a full count of the parts included. If you are missing any parts or have any questions contact us directly

at 888-800-1167

Gather your tools:

Before you begin, make sure that you have gathered all the necessary tools you may require to assemble the unit

properly. Having all of the necessary equipment at hand will save time and make the assembly quick and hassle-free.

Clear your work area:

Make sure that you have cleared away a large enough space to properly assemble the unit. Make sure the space is

free from anything that may cause injury during assembly. After the unit is fully assembled, make sure there is a

comfortable amount of free area around the unit for unobstructed operation.

Invite a friend:

Some of the assembly steps may require heavy lifting. It is recommended that you obtain the assistance of another

person when assembling this product.

User Weight Limitation:

Please note that there is a weight limitation for this product. If you weigh more than 350LBS (Approx. 159 Kgs). It is

not recommended that you use this product. Serious injury may occur if the user’s weight exceeds the limit shown

here. This product is not intended to support users whose weight exceeds this limit.

Care and maintenance:

The safety level can be maintained only if it is examined for damage and wear.

Replace any defective components immediately and stop all use of the equipment until repaired.

Always take care when mounting the equipment. Straddle the equipment by placing your feet on the straddle rails.

Dismount from the equipment only after all parts have stopped.

Always check the wear and tear components like pulley, belts, etc.…To prevent injury.

There is an emergency stop, in the form of a SAFETY KEY, to prevent injury; you can stop the treadmill immediately

by actuating the emergency stop for emergency dismount.

www.smoothfitness.com

7

SUPPLIED COMPONENTS / SUPPLIED HARDWARE

This list identifies the major components you will use to assemble this product.

Treadmill instruction

s

Millimeters

Treadmill

Silicon bottler

Manual

Hardware pack

Safety key

Base frame cover

Bottle Holder

Console

Handle pulse

Handle

bar

Upright post

Motor cover

Running

Side rail

R rear cover

L rear cover

Main frame

Base frame

8 675iO/BT TREADMILL

SUPPLIED COMPONENTS / SUPPLIED HARDWARE

This list identifies the hardware components you will use to assemble this product.

Allen socket head half thread screw

（M8*55*20） 4pcs

Phillips Screwdriver /

Wrench 1pcs

T Allen wrench( S6) 1pcs

Allen socket head full thread screw

（M8*20） 2pcs

Phillips head self-tapping

screw ST4*20 4pcs

Millimeters

www.smoothfitness.com

9

COMPLETE PARTS LIST

Item No. Description Qty.

675iO/BT-1

Base frame

1

675iO/BT-2

Platform frame

1

675iO/BT-3

Incline frame

1

675iO/BT-4

Upright frame

2

675iO/BT-5

Allen socket half thread screw M8*20

2

675iO/BT-6

Motor board welding

1

675iO/BT-7

Computer frame

1

675iO/BT-8

Outside extension tube

1

675iO/BT-9

Inside extension tube

1

675iO/BT-10

IPAD shelf

1

675iO/BT-11

Allen C.K.S. half thread screw M10*65*20

1

675iO/BT-12

Allen C.K.S. half thread screw M10*35*20

2

675iO/BT-13

Allen C.K.S. half thread screw M10*45*20

1

675iO/BT-14

Allen C.K.S. half thread screw M8*50*20

2

675iO/BT-15

Allen C.K.S. half thread screw M8*55*20

8

675iO/BT-16

Allen C.K.S. half thread screw M8*40*20

4

675iO/BT-17

Allen C.K.S. full thread screw M8*30*20

2

675iO/BT-18

Allen socket half thread screw M8*65

2

675iO/BT-19

Allen socket half thread screw M8*75

2

675iO/BT-20

Allen C.K.S. full thread screw M8*75

2

675iO/BT-21

Allen C.K.S. half thread screw M8*45*20

1

675iO/BT-22

Philips self-tapping screw ST3*10

4

675iO/BT-23

Hex full thread screw M8*75

1

675iO/BT-24

Motor welding screw M8*65

1

675iO/BT-25

Hex self-locking nut M8*20

2

675iO/BT-26

Spring Washer Φ8

2

675iO/BT-27

Philips C.K.S.full thread screw M6*25

8

675iO/BT-28

Philips C.K.S.full thread screw M5*20

7

675iO/BT-29

Philips C.K.S.full thread screw M5*10

10

675iO/BT-30

Philips C.K.S.full thread screw M4*10

9

675iO/BT-31

Philips self-taping screw ST4*16

31

675iO/BT-32

Philips self-taping screw ST4*16

2

675iO/BT-33

Philips self-taping screw ST4*16

27

675iO/BT-34

Washer Φ8

12

675iO/BT-35

Philips self-taping screw ST4*16

8

675iO/BT-36

Philips self-taping screw ST3*10

2

675iO/BT-37

Philips C.K.S.full thread screw ST4*15

7

675iO/BT-38

Washer Φ10

3

675iO/BT-39

Washer Φ14

2

675iO/BT-40

Washer Φ5

1

10 675iO/BT TREADMILL

COMPLETE PARTS LIST

Item No. Description Qty.

675iO/BT-41

Self half thread screw M12*14*35*19

2

675iO/BT-42

locking nut M10

3

675iO/BT-43

locking nut M8

9

675iO/BT-44

powder metallurgy

2

675iO/BT-45

Motor cover left

1

675iO/BT-46

Motor cover middle

1

675iO/BT-47

Motor cover right

1

675iO/BT-48

Side rail

2

675iO/BT-49

Central side rail

2

675iO/BT-50

End cover left

1

675iO/BT-51

End cover right

1

675iO/BT-52

Computer housing

1

675iO/BT-53

LCD computer pcb

1

675iO/BT-54

Fan cover

1

675iO/BT-55

Speaker cover left

1

675iO/BT-56

Speaker cover right

1

675iO/BT-57

Accessory tray

1

675iO/BT-58

Safety key

1

675iO/BT-59

Speed handle pulse

1

675iO/BT-60

Round tube

1

675iO/BT-61

Pipe

2

675iO/BT-62

fan

2

675iO/BT-63

Feet pad

2

675iO/BT-64

Base frame cover left

1

675iO/BT-65

Base frame cover right

1

675iO/BT-66

Square cushion 35*35*t3.0*φ9

2

675iO/BT-67

Square cushion 35*35*t5.0*φ8

4

675iO/BT-68

Under board cover

1

675iO/BT-69

Round cushion

8

675iO/BT-70

Cover board

1

675iO/BT-71

Wheel φ62

4

675iO/BT-72

Feet board

1

675iO/BT-73

Foam

2

675iO/BT-74

Taper cushion

2

675iO/BT-75

Power code clip

1

675iO/BT-76

Wire clip

2

675iO/BT-77

powder metallurgy φ24*φ19*φ14*14*3

2

675iO/BT-78

Wire clip

8

675iO/BT-79

Ship switch

1

675iO/BT-80

fuse

1

www.smoothfitness.com

11

COMPLETE PARTS LIST

Item No. Description Qty.

675iO/BT-81

controller

1

675iO/BT-82

Power code

1

675iO/BT-83

Speed sensor

1

675iO/BT-84

Washerφ6*φ20*t2.0

8

675iO/BT-85

Wheel φ46

2

675iO/BT-86

motor

1

675iO/BT-87

Incline motor

1

675iO/BT-88

Running board

1

675iO/BT-89

Front roller

1

675iO/BT-90

Rear roller

1

675iO/BT-91

Cylinder

1

675iO/BT-92

Motor belt

1

675iO/BT-93

Running belt

1

675iO/BT-94

Magnet ring

2

675iO/BT-95

Decorate cushion

4

675iO/BT-96

Wire L-1300

1

675iO/BT-97

Wire L-1000

1

675iO/BT-98

Filter (for option)

1

675iO/BT-99

Inductor(for option)

1

675iO/BT-100

Wire L-950

1

675iO/BT-101

Handle bar upper cover left

1

675iO/BT-102

Handle bar down cover

2

675iO/BT-103

Incline handle pulse

1

675iO/BT-104

Philips self-tapping screw ST4*20

4

675iO/BT-105

locking nut M8 (black)

7

675iO/BT-106

spring

2

675iO/BT-107

IPAD part

2

675iO/BT-108

IPAD clip

2

675iO/BT-109

Pipe 2

1

675iO/BT-110

Spring 2

1

675iO/BT-111

Handle bar upper cover right

1

675iO/BT-112

binder plate

2

675iO/BT-113

Computer housing back cover

1

12 675iO/BT TREADMILL

PARTS DIAGRAM

MOST OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED

30

98

99

2

9

8

1

6

11

12

41

13

112

15

16

17

18

19

20

21

23

24

25

27

106

28

29

30

104

35

36

83

37

39

38

34

39

40

42

105

44

77

45

46

47

48

49

50

51

52

53

55

56

57

58

60

61

63

64

65

66

67

68

69

85

71

72

74

75

76

77

78

79

80

81

82

85

86

87

88

89

90

91

92

93

94

95

31

33

84

43

19

43

34

31

35

61

39

41

77

105

34

71

16

105

34

71

16

3

109

110

105

34

21

31

113

69

95

69

26

35

95

69

95

108

107

22

35

22

34

70

106

28

84

10

www.smoothfitness.com

13

ASSEMBLY – PLEASE READ ALL STEPS BEFORE BEGINNING YOUR WORK.

STEP1: Remove the treadmill and its components from the packaging

NOTE:

Make sure all wires are recessed into the frame. DO NOT trap or

Pinch the wires. Keep hands clear of all moving components.

14 675iO/BT TREADMILL

ASSEMBLY – PLEASE READ ALL STEPS BEFORE BEGINNING YOUR WORK.

STEP 2: Attach the Left and Right Uprights to the Base Frame

NOTE: Do not fully tighten the bolts at this time.

1). Rotate the left and right uprights upward until the bolt holes in the bottom of the

uprights align with the bolt holes in the treadmill base.

2). Insert the 2 x M8*55mm*20mm Allen Head bolts through the base frame and

the left upright. (2 bolts are used on the left side and 2 bolts are used on the right

side)

3). Repeat the above process for the Right side.

#15

X4

Caution Pinch point! Do not pinch wires between the frame during rotation.

ONLY HAND TIGHTEN THE BOLTS

!!Pinch Points!!

www.smoothfitness.com

15

ASSEMBLY

STEP 3: Attach the Computer Console

1). Rotate the Computer Console upwards following the directional arrow. Rotate

the console until the bolt holes in the console frame, align with the bolt holes in

the uprights

2). Insert the

1 x M8*20mm bolt through the Computer Console frame and the left

upright.

3). Repeat the above process for the Right side.

4). Completely tighten all bolts from step 2 and 3 now.

#5

X2

Caution Pinch point! Do not pinch wires between the frame during rotation.

Tighten all bolts and fasteners now

!!Pinch Points!!

16 675iO/BT TREADMILL

ASSEMBLY

Step4: Attach the Base Frame Covers

1). Place the left base frame cover over the left upright and slide it downward

towards the floor.

2). Align the 2 holes in the base frame covers with the two screw holes in the base

frame.

3). Insert the 2 x ST4*20mm Screw through the base frame cover and thread into

the base frame.

4). Repeat the process for the right side.

5). Tighten all fasteners now.

#104

X4

www.smoothfitness.com

17

ASSEMBLY

STEP 5: Attach the Water Bottle to the Computer Console

1). Place the water bottle holder into the hole in the computer console located on

the right.

2). Push down on the bottle holder until the bottle holder snaps in place.

313 X4

18 675iO/BT TREADMILL

ASSEMBLY

STEP 6:

Insert Safety Key (209) into Bottom Center of Console prior to operation. Your

treadmill will not Function with out the safety key.

209 X1

Assembly is now complete. Be sure to routinely

check that the bolts used in assembly are tight

Safety Key Pad

If the safety key is not present the treadmill will not function

www.smoothfitness.com

19

ASSEMBLY

How to fold and unfold the treadmill:

Your treadmill can be folded up and unfold for space saving storage. To do this follow the instructions here:

Fold Up

1. To fold the deck you first need to bring the treadmill

to the lowest incline level and then remove the

power cord

2. Lift the deck up from the rear of the treadmill and

fold up until it locks in place. TO PREVENT INJURY

BE SURE YOU HAVE A FIRM HOLD WHEN

RAISING THE DECK.

3. You will hear a “click” sound as the lock engages.

Unfold

You can unfold the treadmill from the upright position:

1. Begin by standing behind and supporting the deck

with your hands. Next release the lock with your foot

by stepping on the release lever. TO PREVENT

INJURY BE SURE YOU HAVE A FIRM HOLD ON

THE DECK BEFORE RELEASING THE LOCK.

2. Slowly lower the deck until the deck start to lower by

itself. The deck will lower slowly till it rests securely

on the ground. DO NOT STAND UNDER THE

DECK AS IT LOWERS. KEEP ALL OBJECTS

CLEAR AS THE TREADMIL LOWERS.

Horizontal Adjustment

An uneven floor or improper stabilizer level can cause

the treadmill to wobble during use as well as the incline

adjustment to function incorrectly. Please follow the

procedure described below to make sure the treadmill

stabilizer is adjusted correctly prior to use. You may

need the assistance of another person to perform this

adjustment.

First locate the two adjustable stabilizers under the

base frame. Then simply rotate them in or out to

adjust the level of the treadmill. When properly

adjusted the treadmill should sit firmly on both

stabilizers and all cushions.

20 675iO/BT TREADMILL

MAINTAINENCE

HOW TO MAINTAIN YOUR TREADMILL:

Proper maintenance is very important to ensure your treadmill is always in top working condition. Improper maintenance could

cause damage or shorten the life of your treadmill and void the LIMITED WARRANTY coverage.

• Important: DO NOT

use abrasives or solvents to clean the treadmill. To prevent damage to the computer, keep liquids

away and keep it out of direct sunlight.

• Inspect and tighten all parts of the treadmill regularly. Replace any damaged or worn parts immediately.

BELT ADJUSTMENT:

The running belt has been properly adjusted at the factory. However transportation, uneven flooring or other

unpredicted reasons could cause the belt to shift off center resulting in the belt rubbing with the plastic side rail or end

caps and possibly causing damage. To adjust the belt back to it’s proper position please follow the directions below:

1. If your belt tends to walk to the right, rotate the right tension bolt clockwise. We recommend adjustments of

1/4 turn at a time, and follow with a test. If your belt continues to walk to the right, simply adjust the left belt

tension bolt by turning it 1/4 turn counterclockwise, and follow with a test.

2. If your belt tends to walk to the left, rotate the left tension bolt clockwise 1/4 turn at a time, and follow with a

test. If the belt continues to walk to the left, simply adjust the right tension bolt counterclockwise.

3. If your belt appears to be loose, simply tighten both bolts evenly 1/4 turn. If it appears tight, simply loosen

both bolts evenly 1/4 turn.

Right and left tension bolts are located at the rear of the treadmill.

DECK LUBRICATION:

The walking belt has been pre-lubricated at the factory. However, it is recommended that the walking board be

checked periodically for lubrication to ensure optimal treadmill performance. Your treadmill should not have to be

lubricated usually within 3 months.

Smooth Fitness recommends lubricating the walking deck a minimum of twice a year for light use (2 days a week) and

four times a year for heavier use(3 times a week multiple users)

Please visit www.smoothfitness.com

for approved maintenance supplies

La page charge ...

Smooth Fitness 675iO/BT Manuel utilisateur

Smooth Fitness 675iO/BT Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents