Maytag MTW6300TQ - 28" Washer With 3.8 cu. Ft. Capacity Mode d'emploi

Marque: Maytag

Modèle: MTW6300TQ - 28" Washer With 3.8 cu. Ft. Capacity

Catégorie: Machines à laver

Taper: Mode d'emploi

Ce manuel convient également à

MTW6300TQ 3.8

AUTOMATIC

USE & CARE

WASHER

GUIDE

LAVADORA AUTOMATICA CON

MANUAL DE USO Y CUIDADO

LAVEUSE AUTOMATIQUE AVEC

GUIDE D'UTILISATION ET D'ENTRETIEN

FOR QUESTIONS ABOUT FEATURES, OPERATION/PERFORMANCE,

PARTS, ACCESSORIES OR SERVICE CAI.I.: 1.800.688.9900

IN CANADA, CAI.I.: 1.800.807.6777

VISIT OUR WEBSITE AT WWW.MAYTAG.COM

IN CANADA, WWW.MAYTAG.CA

SI TIENE PREGUNTAS RESPECTO AI.AS CARACTERiSTICAS,

FUNCIONAMIENTO, RENDIMIENTO, PARTES, ACCESORIOS O

SERVICIO TECNICO, I.I.AME AI.: 1.800.688.9900

EN CANADA, I.I.AME AI.: 1.800.807.6777

VISITE NUESTRO SITIO WEB EN

WWW. MAYTAG. COM

EN CANAD,& WWW, MAYTAG,CA

AU CANADA, POUR ASSISTANCE, INSTAI.I.ATION OU SERVICE,

COMPOSER I.E : 1.800.807.6777

OU VISITER NOTRE SITE INTERNET ,_

WWW. MAYTAG. CA

W10092684A

TABLE OF CONTENTS

WASHER SAFETY .................................................................. 3

INSTALLATION REQUIREMENTS ......................................... 4

Tools and Parts ................................................................... 4

I.ocation Requirements ....................................................... 5

L-)rain System ...................................................................... 6

Electrical Requirements ...................................................... 6

INSTALLATION INSTRUCTIONS ......................................... 7

Before You Start ................................................................. 7

Remove Shipping Base and Packing Ring .......................... 7

Connect Drain Hose .......................................................... 8

Connect the Inlet Hoses ..................................................... 9

Secure the L-)rain Hose ..................................................... 10

I_eve[ the Washer .............................................................. 10

Complete Installation ....................................................... 11

BENEFITS AND FEATURES .................................................. 12

Benefits ..............................................................................

Features ............................................................................ 12

WASHER USE ...................................................................... 13

Starting Your Washer ....................................................... 13

Pausing or Restarting the Washer ..................................... 14

Stopping the Washer ........................................................ 14

Changing Cycles, Modifiers and Options ......................... 14

Status Lights ...................................................................... 15

CycHes .............................................................................. 15

Modifiers .......................................................................... 16

Options ............................................................................ 17

Operating Controls ........................................................... 18

Norma[ Sounds ................................................................ 18

LAUNDRY TIPS ................................................................... 18

WASHER CARE .................................................................... 19

CHeaning Your Washer ..................................................... 19

Water Inlet Hoses ............................................................. 19

Vacation, Storage and Moving Care ................................. 19

TROUBLESHOOTING ......................................................... 20

Washer and Components ................................................. 20

Washer Operation ............................................................ 21

CHothing Care ................................................................... 22

ASSISTANCE OR SERVICE ................................................... 24

In the U.S.A ...................................................................... 24

In Canada ......................................................................... 24

WARRANTY ....................................................................... 25

INDICE

SEGURIDAD DE LA LAVADORA ....................................... 26

REQUISITOS DE INSTALACION ........................................ 27

Piezas y herramientas ...................................................... 27

Requisitos de ubicaci6n ................................................... 28

Sistema de desagLie ......................................................... 29

Requisitos e[6ctricos ........................................................ 29

INSTRUCClONES DE INSTALAClON ................................ 30

Antes de comenzar .......................................................... 30

Quite [a base y el ani[[o de emba[aje .............................. 30

Conecte Hamanguera de desagLie .................................... 31

Conexi6n de [as mangueras de entrada ........................... 32

Fijaci6n de [a manguera de desagLie ................................ 33

NiveHaci6n de Ha[avadora ................................................ 33

CompHete HainstaHaci6n ................................................... 34

BENEFIClOS Y CARACTERI'STICAS .................................... 35

Beneficios ........................................................................ 35

Caracter_sticas ................................................................. 35

USO DE LA LAVADORA .................................................... 36

Puesta en marcha de Ha[avadora ..................................... 36

Pausa o reanudaci6n de [a marcha de [a [avadora .......... 37

C6mo detener Ha[avadora ............................................... 37

Cambio de cic[os, modificadores y opciones .................. 38

Luces de estado ............................................................... 38

CicHos .............................................................................. 38

Modificadores .................................................................. 40

Opciones ......................................................................... 41

Contro[es de funcionamiento .......................................... 41

Sonidos normaHes ..............................................................

CONSEJOS DE LAVANDERI'A ............................................ 42

CUIDADO DE LA LAVADORA .......................................... 43

C6mo [impiar su [avadora ............................................... 43

Mangueras de entrada de agua ........................................ 43

Cuidado durante [as vacaciones, el a[macenamiento

y Hasmudanzas ................................................................ 43

SOLUClON DE PROBLEMAS ............................................. 44

I.avadora y componentes ................................................. 44

Funcionamiento de Ha[avadora ....................................... 46

Cuidado de Haropa .......................................................... 47

AYUDA O SERVIClO TI_CNICO ......................................... 49

En los EE.UU ................................................................... 49

En Canada" ....................................................................... 49

GARANTI'A ......................................................................... 50

TABLE DES MATIERES

SI_CURITI_ DE LA LAVEUSE ................................................. 51

EXIGENCES DqNSTALLATION ........................................... 52

Outillage et pi_ces ........................................................... 52

Exigences d'empHacement ................................................ 53

Syst_'me de vidange ......................................................... 54

Sp6cifications 6[ectriques ................................................. 54

INSTRUCTIONS DqNSTALLATION ................................... 55

Avant de commencer ....................................................... 55

Retrait de [a base d'exp6dition et

de ['anneau d'emba[[age .................................................. 55

Raccordement du tuyau de vidange ................................. 56

Raccordement des tuyaux d'a[imentation ........................ 57

ImmobiHisation du tuyau de vidange ................................ 58

R6g[age de ['aplomb de [a [aveuse ................................... 58

Achever ['installation ....................................................... 59

AVANTAGES ET CARACTI_RISTIQUES ............................... 60

Avantages ........................................................................ 60

Caract6ristiques ................................................................ 60

UTILISATION DE LA LAVEUSE ........................................... 61

Mise en marche de Ha[aveuse .......................................... 61

Pause ou remise en marche de Ha[aveuse ........................ 62

Arr6t de Ha[aveuse ........................................................... 62

Changement des programmes, modificateurs et

options ............................................................................. 63

T6moins [umineux ........................................................... 63

Programmes ..................................................................... 63

Modificateurs ................................................................... 65

Options ............................................................................ 66

Fonctionnement des commandes .................................... 66

Sons normaux .................................................................. 67

CONSEILS DE LESSIVAGE ................................................... 67

ENTRETIEN DE LA LAVEUSE .............................................. 68

Nettoyage de votre [aveuse .............................................. 68

Tuyaux d'arriv6e d'eau .................................................... 68

Pr6cautions _ prendre avant [es vacances,

un entreposage ou un d6m6nagement ............................. 68

DI_PANNAGE ...................................................................... 69

I.a [aveuse et ses composants ........................................... 69

Fonctionnement de [a [aveuse ......................................... 71

Soin des v6tements .......................................................... 72

ASSISTANCE OU SERVICE .................................................. 74

Aux Etats-Unis .................................................................. 74

Au Canada ....................................................................... 74

GARANTIE .......................................................................... 75

.........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................i_'iiiiiiiiiiiiiiiiiii_¸ iiiTiTiiiiiTii;;71i;;71i;;71i;;71i;;71i;;71i;;71i;;i_iiiiiii;¸ii_;iiiiiiiiil¸ii_7iiii{i//li;iiii_iiiiii_;_iiiiii_;_iiiiii_iiiiiiiiil;;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_ii¸;i;_;IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

WASHER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

......iiiiiiii_:

i_iiiiiiii,,i_,:

::::::::ii:::....

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions,

including the following:

• Read all instructions before using the washer.

• Do not wash articles that have been previously cleaned

in, washed in, soaked in, or spotted with gasoline,

dry-cleaning solvents, other flammable, or explosive

substances as they give off vapors that could ignite or

explode.

m Do not add gasoline, dry-cleaning solvents, or other

flammable, or explosive substances to the wash water.

These substances give off vapors that could ignite or

explode.

m Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been used

for 2 weeks or more. HYDROGEN GAS IS

EXPLOSIVE. If the hot water system has not been

used for such a period, before using the washing

machine, turn on all hot water faucets and let the water

flow from each for several minutes. This will release

any accumulated hydrogen gas. As the gas is

flammable, do not smoke or use an open flame during

Do not allow children to play on or in the washer. Close

supervision of children is necessary when the washer is used

near children.

Before the washer is removed from service or discarded,

remove the door or lid.

• Do not reach into the washer if the drum, tub or agitator is

moving.

• Do not install or store the washer where it will be exposed to

the weather.

• Do not tamper with controls.

• Do not repair or replace any part of the washer or attempt any

servicing unless specifically recommended inthis manual or in

published user-repair instructions that you understand and

have the skills to carry out.

• See "Electrical Requirements" for grounding instructions.

this time.

SAVE THESE INSTRUCTIONS

INSTALLATION REQUIREMENTS

_'_ 7'__2'

Gather the required tools and parts before starting installation. The parts supplied are in the Parts supplied:

washer basket.

Tools needed for connecting the drain hose and water inlet hoses:

• Pliers that open to 1%6" (3.95 cm) • Flashlight (optional)

NOTE: Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Record hose

installation or replacement dates for future reference.

A B C D

A. Drain hose form C. Flat water inlet hose washers (4)

B. Water inlet hoses (2) D. Beaded tie strap

Tools needed for securing the drain hose and leveling the washer:

• Adjustable or open end • Wood block

wrench %6" (14 mm)

• Ruler or measuring tape

• I.eve[

Alternate Parts

Your installation may require additional parts. If you are interested in purchasing one of the

items listed here, call the toll-free number on the cover or in the "Assistance or Service"

section.

If You Have: You Will Need to Buy:

Laundry tub or standpipe taller Sump pump system (if not already available)

than 96" (2.4 m)

1" (2.5 cm) diameter standpipe 2" (5 cm) diameter to 1" (2.5 cm) diameter standpipe

adapte_; Part Number 3363920 and connector kit Part

Number 285835

Overhead sewer Standard 20 gal. (76 I.) 39" (99 cm) tall drain tub or

utility sink, sump pump and connectors (available

from local plumbing suppliers)

Floor drain Siphon break, Part Number 285834; additional drain

hose, Part Number 8318155 and connector kit,

Part Number 285835

Water faucets beyond reach of fill 2 longer water fill hoses:

hoses 6 fl (1.8 m) Part Number 76314,

10 ft (3.0 m) Part Number 350008

I.int clogged drain Drain protector, Part Number 367031

Selecting the proper location for your washer improves performance and minimizes noise and

possible washer "walk."

Your washer can be installed in a basement, laundry room, closet, or recessed area. See

"Drain System."

IMPORTANT: Do not install or store the washer where it will be exposed to the weathen

Proper installation is your responsibility.

You will need:

• A water heater set to deliver 120°F (49°C) water to the washer.

• A grounded electrical outlet located within 4 ft (1.2 m) of where the power cord is

attached to the back of the washer. See "Electrical Requirements."

• Hot and cold water faucets located within 3 ft (90 cm) of the hot and cold water fill

valves, and water pressure of 20-100 psi (138-690 kPa) for best performance.

• A [eve[ floor with a maximum slope of 1" (2.5 cm) under entire washer. Installing the

washer on carpeting is not recommended.

• A sturdy floor to support the washer weight (washeb water and load) of 315 [bs (143 kgs).

Do not store or operate your washer in temperatures at or below 32°F (0°C). Some water can

remain in the washer and can cause damage in low temperatures. See "Washer Care" for

winterizing information.

Installation spacing for recessed area and closet installations

The following spacing dimensions are recommended for this washer. This washer has been

tested for installation with spacing of 0" (0 cm) clearance on the sides. Recommended

spacing should be considered for the following reasons:

• Additional spacing should be considered for ease of installation and servicing.

• Additional spacing should be considered on all sides of the washer to reduce noise

t ransfer.

• For c[oset insta[[ation with a door, minimum venti[ation openings in the top and bottom of

the door are required. I.ouvered doors with equivalent ventilation openings are ....

acceptable.

• Companion appliance spacing should also be considered.

3"*

(7.6cm)

3"*

(7.6cm)

*Required spacing

A. Front view

B. Side view

C. Closet door with vents

The washer can be installed using the standpipe drain system (floor or wall), the laundry tub

drain system, or the floor drain system. Select the drain hose installation method you need.

See "Tools and Parts."

Standpipe drain system--wall or floor (views A & B)

The standpipe drain requires a minimum diameter standpipe of 2" (5 cm). The minimum

carry-away capacity can be no less than 17 gal. (64 I.) per minute. A 2" (5 cm) diameter to

1" (2.5 cm) diameter standpipe adapter kit is available. See "Tools and Parts."

The top of the standpipe must be at least 39" (99 cm) high and no higher than 96" (244 cm)

from the bottom of the washer.

39 u

(99 Cm)

A B

Laundry tub drain system (view C)

The laundry tub needs a minimum 20 gal. (76 I.) capacity. The top of the laundry tub must be

at least 39" (99 cm) above the floor and no higher than 96" (244 cm) from the bottom of the

washer.

Floor drain system (view D)

The floor drain system requires a siphon break that may be purchased separately. See "Tools

and Parts."

The siphon break must be a minimum of 28" (71 cm) from the bottom of the washer.

Additional hoses might be needed.

C D

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical supply is required. A time-

delay fuse or circuit breaker is recommended. It is recommended that a separate circuit

serving only this appliance be provided.

This washer is equipped with a power supply cord having a 3 prong grounding plug.

To minimize possible shock hazard, the cord must be plugged into a mating, 3 prong,

grounding-type outlet, grounded in accordance with local codes and ordinances. If a

mating outlet is not available, it is the personal responsibility and obligation of the

customer to have the properly grounded outlet installed by a qualified electrician.

• If codes permit and a separate ground wire is used, it is recommended that a qualified

electrician determine that the ground path is adequate.

• Do not ground to a gas pipe.

• Check with a qualified electrician if you are not sure the washer is properly grounded.

• Do not have a fuse in the neutral or ground circuit.

GROUNDING iNSTRUCTiONS

For a grounded, cord=connected washer:

This washer must be grounded, in the event of a malfunction

or breakdown, grounding will reduce the risk of electrical

shock by providing a path of least resistance for electric

current. This washer is equipped with a cord having an

equipment-grounding conductor and a grounding plug. The

plug must be plugged into an appropriate outlet that is

properly installed and grounded in accordance with all local

codes and ordinances.

WARNING: improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or serviceman if you are in

doubt as to whether the appliance is properly grounded.

Do not modify the plug provided with the appliance - if it will

not fit the outlet, have a proper outlet installed by a qualified

electrician.

For a permanently connected washer:

This washer must be connected to a grounded metal,

permanent wiring system, or an equipment grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead on

the appliance.

INSTALLATION INSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install washer.

Failure to do so can result in back or other injury.

NOTE: To avoid floor damage during installation, set the washer onto cardboard before

moving across floor.

IMPORTANT:

• Be sure the foam shipping base has been removed from the bottom of the washer as

directed in the Unpacking Instructions.

• If foam shipping base has not been removed, be sure lid is secured with tape before laying

washer on its back.

• Removing the foam shipping base is necessary for proper operation.

" ) 1

1. Place cardboard supports from shipping carton on floor behind washer for support.

2. Secure the lid with tape.

3. Using 2 or more people, tip the washer onto its back and place on cardboard supports.

4. Remove foam shipping base.

......iil;))ii_

...._i)i:il.....

5. Set washer upright.

6. Removetapefromlid.Openlidandremovefoampackingringfromwashertub.Keep

foampackingringincaseyouneedtomovethewasherinthefuture.

Properconnectionofthedrainhoseprotectsyourfloorsfromdamageduetowaterleakage.

Readandfollowtheseinstructions.

Thedrainhoseisconnectedtoyourwasherandisstoredinsidethewashercabinet.

i //

Remove drain hose from washer cabinet

Pull the corrugated drain hose out of the washer by first grabbing the pull tie. Continue to pull

the hose until the end emerges. I)o not force excess drain hose back into the rear of the

washer.

i .... /

--¢ /

Laundry tub drain or standpipe drain

Connecting the drain hose form to the corrugated drain hose

-T-

4.5"

(11.4 cm)

A. Drain hose reliefs

1. _,ed end of drain hose into one end of form. Place end of drain hose

form into the drain hose refieL

2. Bend the hose over the top of the form and feed into the other end of

the form. Attach the other end of the form into the other drain hose

refieL The hose must extend 4 7/_,, (1 1.4 cm) beyond the form.

To keep drain water from going back into the washer:

• I)o not force excess drain hose into standpipe. Hose should be secure but loose enough

to provide a gap for air.

• Do not lay excess hose on the bottom of the laundry tub.

Floor drain

Do not install the drain hose form on to the corrugated drain hose. You may need additional

parts. See Floor drain under "Tools and Parts."

1°

_'_/__ _ _'_#'(_:_ _ ....

Insert new flat washers (supplied) into each end of the inlet hoses. Firmly seat the washers

in the couplings.

A B

A. Coupling

B. Washer

Connect the inlet hoses to the water faucets

Make sure the washer basket is empty.

2. Attach the hose labeled hot to the hot water faucet. Screw on coupling by hand until it is

seated on the washer.

3. Attach the hose labeled cold to the cold water faucet. Screw on coupling by hand until it

is seated on the washer.

4. Using pliers, tighten the couplings with an additional two-thirds turn.

Clear the water lines

• Run water through both faucets and inlet hoses, into a laundry tub, drainpipe or bucket,

to get rid of particles in the water lines that might clog the inlet valve screens.

• Check the temperature of the water to make sure that the hot water hose is connected to

the hot water faucet and that the cold water hose is connected to the cold water faucet.

i!"'_ii"fii

......i:iiiiii_

Connect the inlet hoses to the washer

A. Hot water inlet valve

B.Cold water inlet valve

1. Attach the hot water hose to the inlet valve labeled hot.

2. Attaching one hose coupling first makes it easier to tighten the connection with pliers.

3. Screw on coupling by hand until it is seated on the washer.

7}ghten the couplings with an additional two-thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can

result.

4. Usingpliers,tightenthecouplingwithanadditionaltwo-thirdsturn.

NOTE:Donotovertightenorusetapeorsealantsonthevalve.Damagetothevalvescan

result.

5. Attachthecoldwaterhosetotheinletvalvelabeledcold.

6. Screwoncouplingbyhanduntilitisseatedonthewasher.

7. Usingpliers,tightenthecouplingwithanadditionaltwo-thirdsturn.

NOTE:Donotovertightenorusetapeorsealantsonthevalve.Damagetothevalvescan

result.

Checkfor leaks

• Turn on the water faucets and check for leaks. A small amount of water might enter the

washer. You will drain this in a later step.

NOTE: Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Record

hose installation or replacement dates for future reference.

• If you connect only one water hose, you must cap off the remaining water inlet port.

• Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are found.

1. Drape the power cord over the console.

2. Remove any cardboard used to move washer.

(2Z>

Beaded tie strap

3. Fasten the drain hose to the laundry tub leg or drain standpipe with the beaded tie strap.

See view A or B.

A B C

If the washer faucets and the drain standpipe are recessed, put the formed end of the drain

hose into the standpipe. Tightly wrap the tie strap around the water inlet hoses and the

drain hose. See view C.

Excessive Weight Hazard

Use two or more people to move and install washer.

Failure to do so can result in back or other injury.

One washer foot has been installed at a different height on your new washer. The other three

feet were preset at the factory. Properly leveling your washer will minimize noise and

vibration.

1. Slide the washer to its final location.

2. Push on upper front panel to be sure the washer is on its rear feet.

3. I.ower right front foot until it contacts the floor. By hand, firmly rotate foot as much as an

additional 1_/_turns. The other three feet have been preset at the factory.

Check the levelness of the washer by first placing a level on the lid near the console.

Next, place the level on the side of the washer in the crease between the top of the

washer and the cabinet.

1. Check the electrical requirements. Be sure that you have the correct electrical supply and

the recommended grounding method. See "Electrical Requirements."

2. Check that all parts are now installed. If there is an extra part, go back through the steps to

see which step was skipped.

3. Check that you have all of your tools.

4. Keep the foam packing ring from the washer tub in case you need to move the washer in

the future. Dispose of/recycle all packaging materials.

5. Check that the water faucets are on.

6. Check for leaks around faucets and inlet hoses.

level the hont.

level the side.

5. If the washer is not level, move the washer out slightly, tip back, prop up the front of the

washer on a wood block. Adjust the feet up or down as necessary by twisting the feet.

Repeat steps 1 through 4 until washer is [eve[.

6. Use a %6" or 14 mm open-end wrench to turn the [ocknut counterclockwise on the foot

tightly against the washer cabinet.

IMPORTANT: If the [ocknut is not tight against the washer cabinet, the washer may

vibrate.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

7. Plug into a grounded 3 prong outlet.

8. Remove any protective film or tape remaining on the washer.

9. Read "Washer Use."

10. To test and to clean your washer measure V2of the detergent manufacturer's

recommended amount of powdered or liquid detergent for a medium-size load and pour

it into the detergent dispenser. Close the lid. Press POWER. Select a normal cycle and

press Start. Allow it to complete one whole cycle.

......iiiiiiii_:

_!!!JJJJJJJJJJJJJJJJJJJJJJJ_

Your washer has several benefits and features that are summarized here. Some items may not apply to your model.

IntelliFill TM Water Level Control

This washer senses the load size and composition through a series of fills and wash motion. It

then adjusts the water level for the best cleaning and rinsing performance. It eliminates the

guesswork. The water level is just right for every wash load size.

Auto Temp Control

The Auto Temp Control on this washer electronically senses and maintains a uniform water

temperature by regulating incoming water temperatures. Using Care Control will help

dissolve detergent.

Dispensers

The dispensers make your washer truly automatic. It is unnecessary for you to return to the

washer during the cycle to add detergent, bleach, or fabric softener.

I.aundry products are added to the load at the proper time in the wash cycle.

Stain Cycle Cleaning Action

The Stain Cycle option uses Direct Inject Cleaning Action to help ensure better soil and stain

removal. Stain Cycle reduces the need for pretreatment. Water flushes through the dispenser

to dissolve the detergent. The detergent mixture is then sprayed onto the load while the

washer spins at low speed. This cleaning action will last up to 10 minutes depending on the

cycle selected. The washer then stops spinning, fills with water to the appropriate level and

continues washing with the selected cycle.

Your new washer includes these features that help to reduce noise, increase the ease of use

and improve wash performance.

Electronic Controls

Electronic controls with preset cycles are easy to use whether you are a beginner or an

"expert."

Quiet Operation

This washer is insulated with sound-dampening materials to reduce washer operation sounds

and noises. On some models, an additional tub wrap is added for superb vibration- and

sound-dampening. The washer has an additional bottom sound pad that is included

separately for installation by the customer.

Suspension System

To reduce washer "walk" and "out of balance" conditions, your new washer combines:

• 4 Spring damper struts to isolate vibration

• Balance ring at the top and bottom of the wash basket to minimize vibration

• Operating software designed to sense and correct off-balance loads

Stainless Steel Basket

The stainless steel basket is corrosion resistant and enables higher spin speeds for more water

extraction than traditional top-load washers, reducing drying time.

See-through Tempered Glass Lid with Solid Hold Lid Hinge (on some models)

Some models feature a see-through glass lid. Made of shatter-proof tempered glass, it shows

the deep cleaning action of the wash load inside. With the solid hold lid hinge, the large lid is

flexible enough to open completely and conveniently, and it won't snap or slam down.

Self-Clean Wash and Rinse Filter System

This washer filters 100% of the wash and rinse water. The water is filtered then recirculated.

The force filter traps sand and dirt, flushing them clown the drain, so they are not redeposited

onto the clean clothes.

Delay Wash (on some models)

Delay Wash allows you to load your washer and pause the start of the cycle for up to 8 hours.

End of Cycle Signal

The End of Cycle Signal produces an audible sound when the wash cycle is finished. This

signal is helpful when you are removing items from the washer as soon as it stops.

12 .....

NOTE: Your washer modem may vary from the modem shown.

POWER

WASH CYCLES MODIFIERS

......]iii_:

i_iiiiiiii,,i_,:

i],S2_

::::::::ii:::....

Fire Hazard

Never place items in the washer that are dampened

with gasoline or other flammable fluids.

No washer can completely remove oil.

Do not dry anything that has ever had any type of oil on

it (including cooking oils).

Doing so can result in death, explosion, or fire.

WARNING: To reduce the risk of fire, electric shock, or injury to persons, read the

IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.

The following is a guide to starting your washer. Periodic references to other sections of this

manual provide more detailed information.

1. Place a load of sorted clothes into the washer. See "l_aundry Tips."

• I.oad evenly to maintain washer balance. Mix large and small items.

• I.oad only to the top of the basket as shown. Overloading can cause poor cleaning.

Items should move easily through the wash water.

Pour measured powdered or liquid detergent into the detergent dispenser. Do not put

detergent directly into the wash tub or onto clothes in the washer.

3. Addcolor-safebleach(powderedorliquid)tothedetergentdispensebifneeded.Besure

tomatchpowderedcolor-safebleachwithpowdereddetergentormatchliquidcolor-safe

bleachwithliquiddetergent.

4. Pourmeasuredliquidchlorinebleachintotheliquidchlorinebleachdispenser,ifneeded.

Bleachisautomaticallydispensedatthepropertimeduringthewashcycle.

5°

I)o not overfill. I)o not dilute. I)o not use more than 1 cup (250 ml.) for a full load.

Use less with a smaller load size.

Follow the garment and the chlorine bleach manufacturer's directions for proper use.

To avoid spilling, use a cup with a pouring spout. I)o not let bleach splash, drip, or run

down into the washer basket.

At the end of the cycle, a small amount of water may be left in the dispenser. This is

normal.

NOTE: Use only liquid chlorine bleach in this dispenser.

Pour measured liquid fabric softener into the fabric softener dispenser, if desired.

IMPORTANT: Dilute all fabric softener with water for a total of 1/2cup (118 ml.).

• I)o not overfill. The dispenser holds 1/2cup (118 ml.).

• I)o not spill or drip any fabric softener onto the clothes.

NOTES:

• Use only liquid fabric softener in this dispenser.

• Do not use fabric softener dispensing balls in this washer. Dispensing balls will not

operate correctly with this washer.

6. Close the washer lid.

7. Press POWER. This turns on the washer display.

8. Select a Wash Cycle. See "Cycles."

9. Adjust the Modifiers, if desired. See "Modifiers."

10. Select desired Options. See "Options."

11. On some modems, select Delay Wash, if desired. See "Delay Wash" in the "Modifiers"

section.

12. PressSTART.The wash cycle begins, and the display shows the estimated remaining time.

The lid will lock.

NOTE: If you do not press Start within 5 minutes of pressing Power, the washer

automatically shuts off.

'_...... ..... _/_

Add a Garment

You can place additional clothing in the wash when the "Add a Garment" status light is

glowing without sacrificing wash performance.

1o add a garment or pause the washer at any time

1. Press PAUSE/CANCEl once.

2. Wait until the lid lock light turns off, then open the lid.

3. Add items.

1o restart the washer

1. Close the lid and press START.

2. To unlock the lid after the Add a Garment period, press PAUSE/CANCEl once. Pressing

PAUSE/CANCEl twice will cancel the wash cycle.

You can stop the wash cycle and drain the tub by pressing the Pause/Cancel button twice or

the Power button once.

s'"= O'"}t)On<

You can change Cycles, Modifiers and Options anytime before Start is pressed. Not all

Modifiers and Options are available for all cycles.

• A short tone sounds when a change is selected.

• Three short tones sound if an unavailable combination is selected. The last selection will

not be accepted.

Changing Cycles after pressing Start

1. Press PAUSE/CANCEl twice to cancel the cycle. The washer will drain.

2. Press POWER.

3. Se[ectthe desired wash cycle.

4. Select the desired Modifiers and Options.

5. Press START.

The washer restarts at the beginning of the new cycle.

NOTE: If you do not press Start within 5 minutes of pausing the washeb the washer

automatically shuts off.

Changing Modifiers and Options after pressing Start

You can change a Modifier or Option anytime before the selected Modifier or Option begins

by choosing the desired Modifiers and/or Options.

NOTE: An error tone will sound if your selection is unavailable.

To manually drain the washer and spin the load

1. Press PAUSE/CANCEl_ twice to cancel the wash cycle and drain the washer.

2. Press POWER.

3. Turn knob to select DRAIN & SPIN.

4. Press START.

When the spin is complete, the lid unlocks. Items can be removed from the washer.

These lights show which portion of the cycle the washer is operating. They also indicate when

you can add other garments to the wash load.

DELAY SOAK WASH RINSE SPIN CLEAN

_0 • • • • • 2

ADD A GARMENT

Indicator lights

An indicator light shows which Cycle, Modifiers and Options you have selected.

Estimated Time Remaining

When a wash cycle is started, the estimated time remaining for the cycle, including fills and

drains, will be displayed. The time will count down to the end of the cycle.

ESTIMATED TIME

REMAINING

Turn the knob to choose the right wash cycle for the type of fabrics you are washing. When

the knob points to a cycle, the indicator light for the cycle will glow. If the default settings for

the Modifiers and Options are suitable for your wash load, you may press Start to begin the

wash cycle.

SUPER NORMAL WRINKLE

WASH ,CONTROL

COLORS/

JEANS

.DELICATE

HAND

SPIN

RINSE

& SPIN

Preset Cycle Settings

For ease of use, preset cycle settings provide the recommended fabric care settings for each

cycle.

To use the preset cycle settings:

1. Press POWER.

2. Select the cycle you want by turning the knob. The preset cycle settings will be displayed

(see the following chart).

NOTE: The preset cycle times may vary slightly depending on your modem.

3. Press START. The wash cycle will begin.

Preset Cycle Settings

Cycle Preset Minutes Soil Level* Wash/Rinse Temp

Whites 73 Heavy Hot/Cold

Super Wash 68 Heavy Hot/Cold

Normal 46 Normal Warm/Cold

Wrinkle Control 46 Medium Warm/Cold

Colors/Jeans 45 Normal Cold/Cold

Delicate 35 Medium Warm/Cold

Handwash 36 I.ight Cold/Cold

Rinse & Spin 33 Not applicable Not applicable

Spin Only 16 Not applicable Not applicable

*Cycle time in minutes will appear in the display while you are making selections. The total

cycle time will appeab including an estimated time for drain and fill times, once Start is

pressed.

NOTE: Load only to the top of the basket. Overloading can cause poor cleaning. See "Starting

Your Washer."

Whites

This cycle introduces liquid chlorine bleach to the load at the proper time for improved

whitening of your heavily soiled white fabrics. Cycle combines high-speed wash action and

high-speed spin. The default option setting for this cycle is Extra Rinse to thoroughly remove

detergent and bleach. For maximum soil and stain removal, liquid chlorine bleach should be

used.

Super Wash

Use this cycle for heavily soiled cotton or sturdy items. Cycle combines high-speed wash

action and high-speed spin. Stain Cycle is the default option for this cycle, but it may be

turned off. See "Changing Cycles, Modifiers and Options."

Normal

Use this cycle for normally soiled cottons and linens, such assheets, blankets and towels. This

cycle combines medium-high speed wash action and high-speed spin.

......iiiiiiii_

.....:"!9

Wrinkle Control

Use this cycle to wash loads of no-iron fabrics such as sport shirts, blouses, casual business

clothes, permanent press and blends. This cycle uses medium-speed wash action, a medium-

speed spin and a cool down process to reduce wrinkling.

Colors/Jeans

Use this cycle for dark or highly dyed natural fabrics such as jeans or other cotton items that

may be susceptible to dye loss. This cycle uses low to medium-speed wash action and high-

speed spin. For best results use cold or warm water.

Delicate

Use this cycle to wash lightly soiled garments indicating "Machine Washable Silks" or

"Gentle" cycle on the care label. This cycle uses low-speed wash action and low spin speeds

for increased fabric care and less wrinkling.

When washing waterproof items, such as plastic-lined mattress pads, shower curtains,

tarpaulin (tarps) or waterproof or water-resistant sleeping bags, use the Delicate or Handwash

cycle with the lowest spin speed setting available for the washer model that you have.

Handwash

Use this cycle to clean lightly soiled special care garments or for items labeled as "Machine

Washable Wool." (Check label instructions to make sure that the garment is washable.) This

cycle uses intermittent-low speed wash action and low-speed spin for the gentlest fabric care

with less wrinkling.

When washing waterproof items, such as plastic-lined mattress pads, shower curtains,

tarpaulin (tarps) or waterproof or water-resistant sleeping bags, use the Delicate or Handwash

cycle with the lowest spin speed setting available for the washer mode[ that you have.

Garments are labeled "Handwash" because:

• The fiber construction may be sensitive to wash action.

• The fabric contains sensitive dyes that may bleed.

NOTE: Some "Handwash" items naturally shrink when washed. Keep this in mind when you

purchase items labeled "Handwash." Items that shrink should be dried flat. When these items

are still wet, "block" them by gently stretching to the original measurements.

Rinse & Spin

Use this option to get a deep rinse followed by a high-speed spin. The time display will

include an estimate of how long it will take to fill and drain the washer.

When to use Rinse & Spin:

• For loads that need rinsing only.

• For completing a cycle after the power has been off.

To use or change Rinse & Spin setting:

1. Turn knob to RINSE & SPIN until the Rinse & Spin indicator light glows.

2. Press START.

Spin Only

An extra drain and spin may help shorten drying times for some heavy fabrics or special-care

items. Spin Only may also be used for draining the washer after canceling a cycle or

completing a cycle after a power failure.

To use or change Spin Only setting:

1. Turn knob to SPIN ONI.Y until the Spin Only indicator light glows.

2. Press START.

Modifiers allow you to further customize your cycles and save energy.

• AUTO AUTO TEMP

....

• SUPER • HOT/COLD

• HEAVY • LARGE • WARM/WARM

• MEDIUM • MEDIUM • WARM/COLD

_T LL D/COl D

SOIL LOAD WASH/RINSE

LEVEL SIZE TEMP

Soil Level

Soil [eve[ (wash time) is preset for each wash cycle. See "Preset Cycle Settings" in "Cycles." As

you press the Soil I_eve[ pad, the cycle time (minutes) will increase or decrease in the

Estimated Time Remaining display and a different wash time will appear. To get the minimum

wash time, press the pad until the indicator light next to I.ight Soil I.eve[ illuminates. This is

the shortest wash time available for that cycle.

• For most loads, use the time recommended in the preset cycle settings.

• For heavy soil and sturdy fabrics, press Soil I.evel to select more wash time, if needed.

• For light soil and delicate fabrics, press Soil I.evel to select less wash time, if needed.

Load Size

This washer automatically selects Auto for the water level when the cycle is selected. The

Auto feature senses the size of the load and adds the correct amount of water for the load size.

You can also manually change the water level settings.

Wash-Rinse Temp

Select a water temperature based on the type of load you are washing. Use the warmest wash

water safe for fabrics. Follow garment label instructions.

Warm rinses leave the loads drier and more comfortable to handle than with cold rinses.

Howeveb warm rinses also increase wrinkling. Cold rinses may help with wrinkling and save

energy.

Temperature Guide

Wash Water Temperature Suggested Fabrics

Hot Whites and pastels

Warm Bright colors

Cold Colors that bleed or fade

NOTE: In wash water temperatures colder than 60°F (15.6°C), detergents do not dissolve we[[.

Soils may be difficult to remove.

Auto Temp Control

Auto Ternp Control electronically senses and maintains a uniform wash and rinse water

temperature. Auto Temp Control regulates incoming hot and cold water and is automatically

turned on when a cycle is selected. (See "Preset Cycle Settings" in "Cycles.")

Auto Temp Control is available with Warm/Warm, Warm/Cold and Cold/Cold settings. The

water temperature in the Hot/Cold setting depends on the water temperature at the water inlet

faucets.

• Auto Tomp Control ensures consistent cleaning.

• Today's detergents work well at temperatures above 60°F (15.6°C).

Delay Wash (on some models)

You can use the Delay Wash feature to delay the start of a wash cycle for up to 8 hours

(depending on your modem).

1. load the washer and fill the dispensers.

2. Close the washer lid.

3. Press POWER.

4. Select the desired Cycle, Modifiers and Options.

5. Press DELAY WASH. 1H (one hour) will be displayed in the time display window. The

indicator light for Delay Wash will glow.

For a longer delay time, press DEI.AY WASH. The Start time will increase by 1-hour steps.

Press START. The countdown in hours to the wash cycle will show in the time display

window and the indicator light will begin to flash.

NOTE: The Start indicator light will not flash when Delay Wash is chosen. You must press

Start to initiate a countdown for the cycle to begin.

To change the Delay Wash time:

• Press PAUSE/CANCEl .....

• Press DEI.AY WASH to select the desired delay time.

• Press START to begin the countdown.

To cancel Delay Wash:

Press START again to begin the cycle right away or press PAUSE/CANCEl twice.

Use these pads to select the desired options for your wash cycle.

STAIN

CYCLE

• HIGH• LOW

EXTRA __

RINSE

PRE- END OF

SOAK CYCLE

SIGNAL

Stain Cycle

This option provides enhanced cleaning action for tough stains. The Heavy Duty cycle .........

automatically includes Stain Cycle. Choosing Stain Cycle will add approximately 10 minutes

to a cycle. Stain Cycle should be started on a dry load only and cannot be selected after the :::::::::::

tub has started filling with water.

1:i

Stain Cycle may be selected as an option with other cycles. See table for details. ....

Cycle Stain Cycle (Adds time to the wash cycle)

Whites Option

Super Wash Defau[t

Normal Option

Wrinkle Control Option

Colors/Jeans Option

Delicate Not available

Handwash Option

Rinse & Spin Not available

Spin Only Not available

Extra Rinse

An extra rinse can be used to aid in the removal of detergent or bleach residue from garments.

This option provides an additional rinse with the same water temperature as the first rinse.

This is the default rinse setting for the Whites cycle.

Pre Soak

Use this option for set-in stains and soil that need extra time for removal. Soaking in this

washer is different than in a conventional washer. The washer sprays the load with water and

detergent at extra-low spin speed followed by a brief pause. This action is repeated. Pre Soak

cycles through a series of sprays followed by a pause to allow the detergent to work on the

soils. The Pre Soak feature is followed by the selected cycle. Using Pre Soak will extend your

wash cycle.

End of Cycle Signal Volume

The End of Cycle Signal produces an audible sound when the wash cycle is finished. This

signal is helpful when you are removing items from the washer as soon as it stops. Select On

or Off.

POWER

START

PAUSE/

CANCEL

LID L_CK

Power

Press POWER to turn the washer on or off.

Pause/Cancel

Press PAUSE/CANCEl. once to pause or stop the washer at any time. Press PAUSE/CANCEl_

once to unlock the lid and add a garment. Press START to complete the cycle from where it

was stopped. Press PAUSE/CANCEl. twice to stop the wash cycle. The washer will then drain

and turn off.

Lid Lock

When the I.id I.ock status light glows, the washer lid is locked.

NOTE: You must wait until the I.id I.ock I.ight turns off before the lid can be opened.

Mock'Heal Sounds

Your new washer may make sounds your old one didn't. Because the sounds might be

unfamiliar, you may be concerned about them. These sounds are normaN.

During washing

If you select the Stain Cycle option, you will hear a spin/spray noise at the start of the cycle.

During drain

If water is drained quickly from your washer (depending on your installation), you may hear

air being pulled through the pump during the end of draining.

Start During wash and spin

Press START to start your washer after a cycle has been selected. Be sure all desired Modifiers This washer does not have a transmission. The motor provides direct drive for agitation and

and Options have been selected. The lid must be dosed for the washer to start, spin. You will hear sounds that are different from those of a conventional washer.

LAUNDRY TIPS

Preparing clothes for washing

Follow these recommendations to help you prolong the life of your garments.

• Close zippers, snaps, and hooks to avoid snagging other items. Remove pins, buckles, and

other hard objects to avoid scratching the washer interior. Remove non-washable trim and

ornaments.

• Empty pockets and turn them inside-out

• Turn down cuffs; brush away lint and dirt.

• Turn synthetic knits inside-out to avoid pilling.

• Tie strings and sashes so they will not tangle.

• Mend tears, loose hems, and seams.

• Treat spots and stains.

• Stained or wet garments should be washed promptly for best results.

Sorting

• Separate heavily soiled items from lightly soiled ones, even if they would normally be

washed together. Separate lint-givers (towels, chenille) from lint-takers (corduroy,

synthetics, permanent press). When possible, turn lint-givers inside-out

Separate dark colors from light colors, colorfast items from noncolorfast items.

Sort by fabric and construction (sturdy cottons, knits, delicate items).

When washing waterproof items, such as plastic-lined mattress pads, shower curtains,

tarpaulin (taps) or waterproof or water-resistant sleeping bags, use the Delicate or

Handwash cycle with the lowest spin speed setting available for the washer mode[ that

you have.

Unloading

• Remove clothes from washer after the cycle is completed. Metal objects such as zippers,

snaps, and buck[es may rust if [eft in the washer basket for a [ong time.

WASHER CARE

_IliiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiB_I{i

C <an des:

Use a soft, damp cloth or sponge to wipe up any spills such as deterge@or bleach from the

outside of your washer.

Clean your washer interior by mixing 1 cup (250 ml_)of chlorine bleach and 2 cups (500 ml_)

of detergent. Pour this mixture into your washer and run itthrough a complete cycle using hot

water. Select the Super I.oad Size. Repeat this process if necessary.

Remove any hard water deposits using only cleaners labeled as washer safe.

Cleaning the liquid fabric softener dispenser:

1. To remove the fabric softener dispenser from the agitator, wrap both hands behind the top

of the fabric softener dispenser and interlock fingers. I.iftup while pulling toward you.

2. Separate the top and base of the dispenser. Rinse all three dispenser parts (the base, the

inner cone-shaped cup and the top) under warm water.

3. For ease of assembly, reassemble the dispenser with the parts upside down.

IMPORTANT:Be sure the inner cone-shaped cup is straight and placed completely in the

top of the dispenser before installing the base.

4. Reinstall the dispensen Be sure it is completely seated. The rim must be tight to the top of

the agitator.

NOTE: To avoid damage to the washer or clothing, do not wash clothes with the liquid fabric

softener dispenser removed or add detergent or bleach to this dispenser; it is for liquid fabric

softener only.

Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Periodically inspect

and replace inlet hoses if bulges, kinks, cuts, wear or leaks are found.

When replacing your inlet hoses, mark the date of replacement on the [abe[ with a permanent

marker.

VI( VII !_ [""_"=_"

Install and store your washer where it will not fleeze. Because some water may stay in the

hoses, freezing can damage your washer. If storing or moving your washer during freezing

weather; winterize it.

Non-use or vacation care:

Operate your washer only when you are at home. If you will be on vacation or not using your

washer for an extended period of time, you should:

• Unplug washer or disconnect power.

• Turn off the water supply to the washer. This helps avoid accidental flooding (due to a

water pressure surge) while you are away.

To winterize washer:

1. Shut off both water faucets.

2. Disconnect and drain water inlet hoses.

4. Run washer on the Rinse & Spin setting for about 30 seconds to mix the antifreeze and

remaining water.

5. Unplug washer or disconnect power.

To use washer again:

1. Flush water pipes and hoses. Reconnect water inlet hoses. Turn on both water faucets.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Plug in washer or reconnect power.

Run the washer using any cycle and a Super I_oad Size water level to clean the washer

and remove the antifreeze, if used. Use 1/2the manufacturer's recommended amount for a

medium-size load.

transport the washer:

Shut off both water faucets.

Disconnect and drain water inlet hoses.

If the washer will be moved during freezing weather, put 1 qt (1 I_)of R.V.-type antifreeze

in the basket. Run washer on the Rinse & Spin setting for about 30 seconds to mix the

antifreeze and remaining water.

Disconnect the drain from the drain system.

Unplug the power cord.

Place the inlet hoses into the basket.

Drape the power cord and drain hose over edge into the basket.

Place foam packing ring from the original shipping materials in the top of washer. If you

do not have the original foam packing ring, place heavy blankets, towels, etc. into basket

opening. Close the lid and put a piece of tape over the lid and down to the front of the

washer. Keep lid taped until the washer is placed into the new location.

3. Put 1 qt (1 L) of R.V.-type antifreeze in the basket.

......]iii_,

...._i!:il.....

i,iiiiiiii,,i_,:

iJ%

Reinstalling the washer

1. Follow the "Installation Instructions" to locate, [eve[ and connect the washer.

2. Run the washer using any cycle and a Super I_oad Size water level to clean the washer

and remove the antifreeze, if used. Use 1/2the manufacturer's recommended amount for a

medium-size load.

TROUBLESHOOTING

First try the solutions suggested here and possibly avoid the cost of a service call...

Washer displaying code messages

• LF" "LF" (Washer is taking too long to fill)

Check the following:

Are the water inlet hoses kinked or clogged?

Are the water inlet valve screens clear?

Press PAUSE/CANCEl_ to clear display.

Is the drain hose installed properly? See "Connect the Drain Hose."

• Ld "Ld" (Washer is taking too long to drain water from the wash tub)

Check the following:

Is the drain hose kinked or clogged?

Is the drain hose installed properly? See "Connect the Drain Hose." Press PAUSE/CANCEl ....

to clear display.

• u_ "uL" (Unbalanced Load)

If the load is unbalanced, the washer will display this code while running an imbalanced

load correction routine at the end of the wash cycle and before the final spin. If the code

remains and the wash cycle dial is flashing after the recovery routine has stopped, open

lid and redistribute the load. Close lid and press START.

• oL. "oL" (Over Load)

Is the washer overloaded? The washer has attempted to fill and begin the wash cycle. If

the washer is overloaded, it will drain any water and detergent that was added during the

fill. To correct the overload, remove several items and add detergent. Close lid and press

START.

_d "Sd" (Suds Detected)

Did you add too much detergent?

Always measure detergent. Follow detergent manufacturer's directions.

If excessive suds are detected, the washer will display this code while running a suds

reduction correction routine at the end of the wash cycle. The suds reduction routine

removes extra suds and assures proper rinsing of your garments. If the code remains and

the wash cycle dial is flashing after the recovery routine has stopped, re-select your

desired cycle using cold water. Press START. Do not add detergent.

td "lid" (Lid Opened)

Is the lid open? Close the lid to clear the display.

i_ 4#HCI' (Cold and Hot hoses switched)

This code will appear at the end of the wash cycle to indicate that the cold and hot water

inlet hoses are switched. If an error code does not appear but you are experiencing poor

washing performance, check to see whether the inlet hoses are reversed. See "Connect

the Inlet Hoses."

• alL. "dL" (Door/Lid cannot lock)

Indicates lid is not locked. Check for items caught in the lid keeping it from closing. Press

PAUSE/CANCEl. once to clear the code.

• dU "dU" (Door/Lid cannot unlock)

Is there excessive weight on the lid, such as a basket of laundry? Excessive weight will

keep the lid from unlocking. Press PAUSE/CANCEl. once to clear the code.

• F__ "F##" code

Press PAUSE/CANCEl_ once to clear code. Press START. If code appears again, call for

service.

Noisy, vibrating, off-balance

• Is the washer level? Does the washer rock when pushed against the corners?

The washer must be level. The front and rear feet must be in firm contact with the floor.

Check that the Iocknuts are tightened. See "l.evel the Washer."

Is the floor flexing, sagging or not level?

Flooring that flexes or is uneven can contribute to noise and vibration of the washer. A

3/4" (1.9 cm) piece of plywood under the washer will reduce the sounds. See "l.ocation

Requirements."

• Is the load balanced?

Evenly distribute the load in the washer basket and make sure the height of the load does

not exceed the top row of basket holes. See "Starting Your Washer."

Do you hear clicking or other noises when the cycle changes from washing to draining

or spinning?

When the drive system shifts or the washer basket settles between cycles you may hear

noises that are different from your previous washer. These are normal washer noises.

• Is the washer gurgling or humming?

When the washer drains, the pump will make a continuous humming with periodic

gurgling or surging sounds as the final amounts of water are removed. This is normal.

• Are you washing a small load?

You will hear more splashing sounds when washing small loads. This is normal.

• The washer basket moves while washing.

This is normal.

La page charge ...

Maytag MTW6300TQ - 28" Washer With 3.8 cu. Ft. Capacity Mode d'emploi

Marque: Maytag

Modèle: MTW6300TQ - 28" Washer With 3.8 cu. Ft. Capacity

Catégorie: Machines à laver

Taper: Mode d'emploi

Ce manuel convient également à

MTW6300TQ 3.8

Télécharger le PDF

rapport

Maytag MTW6300TQ - 28" Washer With 3.8 cu. Ft. Capacity Mode d'emploi

Ce manuel convient également à

Maytag MTW6300TQ - 28" Washer With 3.8 cu. Ft. Capacity Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents