Samsung BD-F5100 Manuel utilisateur

Marque: Samsung

Modèle: BD-F5100

Catégorie: Lecteurs Blu-Ray

Taper: Manuel utilisateur

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service,

please register your product at

www.samsung.com/register

Blu-ray

™

Disc Player

user manual

BD-F5100

ENGLISH

02285B-01-BD-F5100-ZC-ENG.indd 1 2013-07-08 오후 2:22:26

Safety Information

Warning

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK).

NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lighting flash and Arrowhead within the

triangle is a warning sign alerting you to

dangerous voltage inside the product.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE THE

COVER (OR BACK). NO USER SERVICEABLE

PARTS ARE INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

The exclamation point within the triangle

is a warning sign alerting you to important

instructions accompanying the product.

WARNING

• To reduce the risk of fire or electric shock,

do not expose this appliance to rain or

moisture.

FCC NOTE (for U.S.A)

This equipment has been tested and found

to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC

rules. These limits are designed to provide

reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses and can radiate

radio frequency energy and, if not installed

and used in accordance with the instructions,

may cause harmful interference to radio or

television reception, which can be determined

by turning the equipment off and on.

The user is encouraged to try to correct the

interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the

equipment and receiver.

• Connect this equipment into an outlet on

a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/

TV technician for help.

This class B digital product meets all

requirements of the Canadian Interference -

Causing Equipment Regulations.

Note to CATV system installer

This reminder is provided to call the CATV

system installer's attention to Article 820-

40 of the National Electrical Code (Section

54 of Canadian Electrical Code, Part I) that

provides guidelines for proper grounding and,

in particular, specifies that the cable ground

shall be connected to the grounding system

of the building as close to the point of cable

entry as practical.

CLASS 1 LASER PRODUCT

This Compact Disc player is classified as a

CLASS 1 LASER product. Use of controls,

adjustments or performance of procedures

other than those specified herein may result in

hazardous radiation exposure.

DANGER :

• VISIBLE AND INVISIBLE LASER

RADIATION WHEN OPEN. AVOID DIRECT

EXPOSURE TO BEAM. (FDA 21 CFR)

CAUTION :

• CLASS 3B VISIBLE AND INVISIBLE

LASER RADIATION WHEN OPEN. AVOID

EXPOSURE TO THE BEAM. (IEC 60825-1)

• THIS PRODUCT UTILIZES A LASER.

USE OF CONTROLS OR ADJUSTMENTS

OR PERFORMANCE OF PROCEDURES

OTHER THAN THOSE SPECIFIED HEREIN

MAY RESULT IN HAZARDOUS RADIATION

EXPOSURE. DO NOT OPEN COVER AND

DO NOT REPAIR YOURSELF. REFER

SERVICING TO QUALIFIED PERSONNEL.

CLASS 1 LASER PRODUCT

KLASSE 1 LASER PRODUKT

LUOKAN 1 LASER LAITE

KLASS 1 LASER APPARAT

PRODUCTO LÁSER CLASE 1

✎

NOTES

If the Region number of a Blu-ray Disc/DVDs

does not correspond to the Region number of

this player, the player cannot play the disc.

Precautions

Important Safety Instructions

Read these operating instructions carefully

before using the unit. Follow all the safety

instructions listed below.

Keep these operating instructions handy for

future reference.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings.

Install in accordance with the

manufacturer's instructions.

8. Do not install near any heat sources

such as radiators, heat registers,

stoves, or other apparatus (including AV

receivers) that produce heat.

9. Do not defeat the safety purpose of

the polarized or grounding-type plug.

A polarized plug has two blades with

one wider than the other. A grounding

type plug has two blades and a third

grounding prong. The wide blade or

the third prong are provided for your

safety. If the provided plug does not fit

into your outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being

walked on or pinched particularly at

plugs, convenience receptacles, and the

point where it exits the apparatus.

11. Only use attachments/accessories

specified by the manufacturer.

02285B-01-BD-F5100-ZC-ENG.indd 2 2013-07-08 오후 2:22:26

Contents

12.

Use only with the cart,

stand, tripod, bracket,

or table specified by

the manufacturer,

or sold with the

apparatus. When

a cart is used, use

caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning

storms or when unused for long periods

of time.

14. Refer all servicing to qualified service

personnel. Servicing is required when

the apparatus has been damaged in any

way, such as when the power-supply

cord or plug is damaged, liquid has

been spilled or objects have fallen into

the apparatus, the apparatus has been

exposed to rain or moisture, does not

operate normally, or has been dropped.

Disc Storage & Management

• Holding Discs

- Fingerprints or scratches

on a disc may reduce

sound and picture quality

or cause skipping

- Avoid touching the surface of a disc

where data has been recorded.

- Hold the disc by the edges so that

fingerprints will not get on the surface.

- Do not stick paper or tape on the disc.

• Cleaning Discs

- If you get fingerprints or dirt

on a disc, clean it with a mild

detergent diluted in water

and wipe with a soft cloth.

- When cleaning, wipe gently

from the inside to the outside of the disc.

• Disc Storage

Do not keep in direct sunlight.

Keep in a cool ventilated area.

Keep in a clean protection jacket and

store vertically.

Handling Cautions

• Do not expose this apparatus to dripping

or splashing. Do not put objects filled with

liquids, such as vases on the apparatus.

• To turn this apparatus off completely, you

must pull the power plug out of the wall

socket. Consequently, the power plug must

be easily and readily accessible at all times.

• Do not plug multiple electric devices into

the same wall socket. Overloading a socket

can cause it to overheat, resulting in a fire.

• Before connecting other components to

this player, be sure to turn them off.

•

If you move your player suddenly from a cold

place to a warm place, condensation may

occur on the operating parts and lens and

cause abnormal disc playback. If this occurs,

unplug the player, wait for two hours, and

then connect the plug to the power outlet.

Then, insert the disc, and try to play back

again.

• If the product makes an abnormal noise

or produces a burning smell or smoke,

turn off the power switch immediately and

disconnect the power plug from the wall

outlet. Then, contact the nearest customer

service center for technical assistance. Do

not use the product. Using the product as

it is may cause a fire or an electric shock.

user's manual may be reproduced or copied

without the prior written permission of

Samsung Electronics Co.,Ltd.

SAFETY INFORMATION

Warning ....................................................... 2

Precautions .................................................2

Disc Storage & Management ....................... 3

Handling Cautions ....................................... 3

GETTING STARTED

Before using the User Manual ......................4

Logos of Discs the player can play .............. 4

Accessories ................................................. 6

Front Panel .................................................. 6

Rear Panel ................................................... 6

Remote Control ........................................... 7

CONNECTIONS

Connecting to a TV ...................................... 7

Connecting to an Audio System .................. 8

Connecting to a Network Router ................. 8

SETTINGS

The Initial Settings Procedure.......................9

Menu Navigation .......................................... 9

Accessing the Settings Menu ...................... 9

Display Settings ........................................... 9

Audio Settings ........................................... 10

Network Settings ....................................... 11

System Settings ........................................ 12

Language Settings ..................................... 13

Security Settings........................................13

General Settings ........................................ 13

Support Settings ....................................... 13

MEDIA PLAY

Playing a Commercially Recorded Disc ...... 14

Playing Files on a USB Device ................... 14

Playing a Disc with User Recorded Content

.. 15

Playing Content Located in Your PC .......... 15

Controlling Video Playback ........................16

Controlling Music Playback ........................16

Playing Photo Contents ............................. 17

APPENDIX

Troubleshooting ......................................... 18

Specifications ............................................ 19

02285B-01-BD-F5100-ZC-ENG.indd 3 2013-07-08 오후 2:22:28

Getting Started

Before using the User Manual

Disc Types and Contents your player can play

Media Disc Type Details

VIDEO

Blu-ray Disc BD-ROM or BD-RE/-R recorded in the BD-RE format.

DVD-VIDEO

DVD-RW

DVD-R

DVD+RW

DVD+R

DVD-VIDEO, recorded DVD+RW/DVD-RW(V)/DVD-R/+R that have

been recorded and finalized, or a USB storage media containing MKV

or MP4 contents.

MUSIC

CD-RW/-R,

DVD-RW/-R,

BD-RE/-R

Music recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R or a USB

storage media containing MP3 or WMA contents.

PHOTO

CD-RW/-R,

DVD-RW/-R,

BD-RE/-R

Photos recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R or a USB

storage media containing JPEG contents.

✎

NOTES

The player may not play certain CD-RW/-R and DVD-R because of the disc type or recording conditions.

If a DVD-RW/-R has not been recorded properly in DVD video format, it will not be playable.

Your player will not play content that has been recorded on a DVD-R at a bit-rate that exceeds 10 Mbps.

Your player will not play content that has been recorded on a BD-R or USB device at a bitrate that exceeds

25 Mbps.

Playback may not work for some types of discs, or when you use specific functions, such as angle change

and aspect ratio adjustment. Information about the discs is written in detail on the disc box. Please refer to

this if necessary.

When you play a BD-J title, loading may take longer than a normal title or some functions may perform slowly.

Disc types your player cannot play

• HD DVD

• DVD-ROM/PD/

MV, etc

• DVD-RAM

• Super Audio CD

(except CD layer)

• DVD-RW (VR mode)

• CVD/CD-ROM/

CDV/CD-G/CD-I/LD

(CD-Gs play audio

only, not graphics.)

• 3.9 GB DVD-R for

Authoring.

Region Code

Both players and discs are coded by region.

These regional codes must match for a disc

to play. If the codes do not match, the disc

will not play.

The Region Code for this player is displayed

on the rear panel of the player.

Disc Type

Region

Code

Area

Blu-ray

Disc

North America, Central

America, South America,

Korea, Japan, Taiwan, Hong

Kong and South East Asia.

DVD-

VIDEO

The U.S., U.S. territories and

Canada

Logos of Discs the player can play

Blu-ray Disc BD-LIVE

NTSC broadcast system in U.S.A, Canada, Korea, Japan

Supported File Formats

Notes on the USB connection

• Your player supports USB storage media,

MP3 players, digital cameras, and USB

card readers.

• The player does not support folder or file

names longer than 128 characters.

•

Some USB/External HDD/digital camera

devices may not be compatible with the player.

• Your player supports the FAT16, FAT32,

and NTFS file systems.

•

Connect USB devices directly to the player’s

USB port. Connecting through a USB cable

may cause compatibility problems.

• Inserting more than one memory device

into a multi-card reader may cause the

reader to operate improperly.

•

The player does not support the PTP protocol.

• Do not disconnect a USB device during a

"loading" process.

• The bigger the image resolution, the longer

the image takes to display.

• This player cannot play MP3 files with DRM

(Digital Rights Management) downloaded

from commercial sites.

•

Your player only supports video with a

frame rate under 30fps (frames per second).

• Your player only supports USB Mass

Storage Class (MSC) devices such as

thumb drives and USB HDD. (HUB is not

supported.)

• Certain USB HDD Devices, multi-card

readers and thumb drives may not be

compatible with this player.

• If some USB devices require excessive

power, they may be limited by the circuit

safety device.

02285B-01-BD-F5100-ZC-ENG.indd 4 2013-07-08 오후 2:22:30

• If playback from a USB HDD is unstable, provide additional power by plugging the HDD into

a wall socket.

If the problem continues, contact the USB HDD manufacturer.

• You must remove the USB storage device safely by performing the "Safely Remove USB"

function to prevent possible damage to the USB memory.

Press the HOME button to move to the home screen, press the YELLOW (C) button, and

then press the

button.

• SAMSUNG is not responsible for any data file damage or data loss.

• Your player does not support NTFS compressed files, sparse files, or encrypted files.

• You can repair or format a USB device on your Desktop PC. (MS-Windows OS only)

Video File Support

File Extension Container Video Codec Audio Codec Resolution

*.avi

AVI

MP4v3

MP3

Dolby Digital

DTS

WMA

PCM

1920x1080

H.264 BP/MP/HP

1920x1080

*.mkv

MKV

VC-1 AP

MP3

Dolby Digital

DTS

1920x1080

H.264 BP/MP/HP

1920x1080

*.wmv

WMV (wmv9)

VC-1 AP

WMA

1920x1080

VC-1 SM

1920x1080

*.mp4

MP4

MP4 (mp4v)

AAC

1920x1080

H.264 BP/MP/HP

1920x1080

*.mpg

*.mpeg

MPEG1

MP1, 2

Dolby Digital

DTS

1920x1080

MPEG2

1920x1080

H.264 BP/MP/HP

1920x1080

• Limitations

- Even when a file is encoded by a supported codec listed above, the file might not be

played if its content has a problem.

- Normal playback is not guaranteed if the file’s container information is wrong or the file

itself is corrupted.

- Files having a higher Bit rate/frame rate than standard may stutter during sound/video playback.

- The Seek (skip) function is not available if the file’s index table is damaged.

• Video decoder

- Supports up to H.264 Level 4.1 and AVCHD

- Does not support H.264 FMO/ASO/RS and VC1 SP/MP/AP L4

- MPEG4 SP, ASP :

Below 1280 x 720 : 60 frames max

Above 1280 x 720 : 30 frames max

- Does not support GMC 2 or higher

• Audio decoder

- Supports WMA 7, 8, 9 and STD

- Does not support WMA sampling rate of 22050Hz mono.

- AAC: Max sampling rate: 96Khz (8, 11, 12, 16, 22,24, 32,44.1, 48, 64, 88.2, 96)

Max bitrate: 320kbps

Music File Support

File Extension Container Audio Codec Support Range

*.mp3

MP3 MP3

*.wma

WMA WMA

* Sampling rates (in kHz) - 8, 11, 16, 22, 32, 44.1, 48

* Bit rates - All bit-rates from 5kbps to 355kbps

Picture File Support

File Extension Type Resolution

*.jpg

*.jpeg

*.jpe

JPEG

15360x8640

*.png

PNG

15360x8640

02285B-01-BD-F5100-ZC-ENG.indd 5 2013-07-08 오후 2:22:30

Front Panel

✎

NOTES

When the player displays the Blu-ray Disc menu, you cannot start the movie by pressing the Play button

on the player or the remote. To play the movie, you must select Play Movie or Start in the disc menu, and

then press the

button.

You can perform software upgrades using the USB Host jack with a USB flash memory stick only.

Rear Panel

USB HOST

REMOTE CONTROL SENSOR

DISC TRAY

PLAY/PAUSE BUTTON

STOP BUTTON

POWER BUTTON

OPEN/CLOSE BUTTON

HDMI OUT LAN DIGITAL AUDIO OUT

AVCHD (Advanced Video Codec High Definition)

• This player can play back AVCHD format discs. These discs are normally recorded and used

in camcorders.

• The AVCHD format is a high definition digital video camera format.

• The MPEG-4 AVC/H.264 format compresses images with greater efficiency than the

conventional image compressing format.

• Some AVCHD discs use the "x.v.Color" format. This player can play back AVCHD discs that

use "x.v.Color" format.

• "x.v.Color" is a trademark of Sony Corporation.

• "AVCHD" and the AVCHD logo are trademarks of Matsushita Electronic Industrial Co., Ltd.

and Sony Corporation.

✎

NOTES

Some AVCHD format discs may not play, depending on the recording condition.

AVCHD format discs need to be finalized.

"x.v.Color" offers a wider color range than normal DVD camcorder discs.

Some MKV and MP4 format discs may not play, depending on the video resolution and frame rate condition.

Accessories

Check for the supplied accessories shown below.

SCREEN

VIEW A-B

FULLBONUS REPEATREPEAT

Batteries for Remote Control

(AAA Size)

User Manual Remote Control

02285B-01-BD-F5100-ZC-ENG.indd 6 2013-07-08 오후 2:22:32

Remote Control

Tour of the Remote Control

Installing batteries

SCREEN

VIEW A-B

FULLBONUS REPEATREPEAT

Turn the player on and off.

Allows you to repeat A-B disc.

Press the number buttons to operate options.

Press to open and close the disc tray.

Use to enter the disc menu.

Press to skip backwards or forwards.

Press to stop a disc.

Press to use bonusview function.

Return to the previous menu.

These buttons are used both for menus on the

player and also several Blu-ray Disc functions.

Use to select menu items and change menu

values.

Press to use the Tools menu.

Use to access various audio functions on a

disc (Blu-ray Disc/DVD).

Press to play a disc.

Press to pause a disc.

Turn the TV on and off.

Press to switch the Blu-ray Disc/DVD’s

subtitle language.

Use to enter the popup menu/title menu.

Press to search a disc backwards or

forwards.

Press to move to the Home menu.

Press to see the full screen on a TV.

During the Blu-ray Disc/DVDs playback, Full

Screen button does not operate.

Press to exit the menu.

Use to display the playback information

when playing a Blu-ray Disc/DVDs.

Allows you to repeat a title, chapter, track or

disc.

TV volume adjustment.

After setup, allows you to set the input

source on your TV.

✎

NOTES

If the remote does not operate properly:

•

Check the polarity (+/–) of the batteries.

•

Check if the batteries are drained.

•

Check if the remote sensor is blocked by

obstacles.

•

Check if there is any fluorescent lighting nearby.

CAUTION

Dispose of batteries according to local environmental

regulations. Do not put them in the household trash.

Connections

Connecting to a TV

Connect an HDMI cable (not supplied) from the HDMI OUT jack on the back of the product to

the HDMI IN jack on your TV.

- Do not connect the power cord to the wall outlet until you have made all the other

connections.

- When you change the connections, turn off all devices before you start.

✎

NOTES

If you use an HDMI-to-DVI cable to connect to your display device, you must also connect the Digital Audio

Out on the player to an audio system to hear audio.

An HDMI cable outputs digital video and audio, so you don't need to connect an audio cable.

Depending on your TV, certain HDMI output resolutions may not work. Please refer to the user manual of

your TV.

When you connect the player to your TV using the HDMI cable or to a new TV, and then turn it on for the

first time, the player automatically sets the HDMI output resolution to the highest supported by the TV.

A long HDMI cable may cause screen noise. If this occurs, set HDMI Deep Color to Off in the menu.

To view video in the HDMI 720p, 1080i, or 1080p output mode, you must use a High speed (category 2)

HDMI cable.

HDMI outputs only a pure digital signal to the TV.

If your TV does not support HDCP (High-bandwidth Digital Content Protection), random noise appears on

the screen.

Audio

Video

02285B-01-BD-F5100-ZC-ENG.indd 7 2013-07-08 오후 2:22:33

Connecting to an Audio System

You can connect the Blu-ray player to an audio system using one of the methods illustrated

below.

- Do not connect the power cord to the wall outlet until you have made all the other

connections.

- When you change the connections, turn off all devices before you start.

Method 1 Connecting to an HDMI supported AV receiver

• Connect an HDMI cable (not supplied) from the HDMI OUT jack on the back of the product

to the HDMI IN jack on your receiver.

• Best quality (Recommended)

Method 2 Connecting to an AV receiver with Dolby Digital or a DTS decoder

• Using a digital Coaxial cable (not supplied), connect the Coaxial Digital Audio Out jack on the

product to the Digital Coaxial In jack of the receiver.

• Good quality

• You will hear sound only through the front two speakers with Digital Output set to PCM.

AudioAudio

Method 2Method 1

Connecting to a Network Router

You can connect your player to your network router using one of the methods illustrated below.

To use the DLNA network functionality, you must connect your PC to your network as shown

in the illustrations.

Wired Network

✎

NOTES

Internet access to Samsung's software update server may not be allowed, depending on the router you use or your

ISP's policy. For more information, contact your ISP (Internet Service Provider).

DSL users, please use a router to make a network connection.

Broadband

service

Broadband

service

Broadband modem

(with integrated router)

Broadband

modem

Router

02285B-01-BD-F5100-ZC-ENG.indd 8 2013-07-08 오후 2:22:34

Settings

The Initial Settings Procedure

• The Home screen will not appear if you do not

configure the initial settings.

• The OSD (On Screen Display) may change in this

player after you upgrade the software version.

• The access steps may differ depending on the

menu you selected.

•

After the initial settings process is complete, you can

then operate the panel buttons and remote control.

The Initial Settings Procedure appears when

you turn on player for the first time and lets you

set the OSD and menu languages, configure

the connection to your home network, and

choose the aspect ratio output (screen size

and format) that is correct for your TV. Follow

the directions that appear on the screen.

✎

NOTES

The Home menu will not appear if you do not

configure the initial settings except as noted below.

If you press the BLUE (D) button during

network setup, you can access the Home menu

even if the network setup is not completed yet.

When you return to the Home menu, the full

screen mode is cancelled automatically.

If you want to display the Initial Setting screen

again to make changes, press the

button on

the front panel of the player for more than 5

seconds with no disc inserted. This resets the

player to its default settings.

After the initial settings process is complete, you

can operate the HDMI-CEC function.

If you want to use the Anynet+(HDMI-CEC)

function to aid in the initial set up process,

please follow the instructions below.

Connect the player to an Anynet+(HDMI-

CEC) compliant Samsung TV using HDMI Cable.

2) Set the Anynet+(HDMI-CEC) feature to On in

both the TV and the player.

3) Set the TV to the Initial Settings Procedure.

If you leave the player in the stop mode for

more than 5 minutes without using it, a screen

saver will appear on your TV. If the player is

left in the screen saver mode for more than 25

minutes, the power will automatically turn off.

Menu Navigation

HOME Button : Press to move to the Home

menu.

RETURN Button :

Return to the previous menu.

(Enter) / DIRECTION Button :

Move the cursor or select an item.

Activate the currently selected item.

Confirm a setting.

EXIT Button : Press to exit the current menu.

• Home Menu

Selects Music.

Selects Settings.

Displays the buttons you can use on the

remote to access functions.

Selects applications.

Selects Videos.

Selects Photos.

✎

NOTES

The Videos, Photos, and Music options require

that you have an appropriate disc inserted into

the player or a USB flash device attached to

the player.

Accessing the Settings Menu

To access the Settings menu and sub-menus,

follow these steps:

1. Press the POWER button.

The Home Menu appears.

Press the ◄► buttons to select Settings,

and then press the

button.

3. Press the ▲▼ buttons to select the

desired submenu, and then press the

button.

Press the ▲▼ buttons to select the desired

item, and then press the

button.

5. Press the EXIT button to exit the menu.

✎

NOTES

The access steps may differ depending on

the menu you selected. The OSD (On Screen

Display) may change in this player after you

upgrade the software version.

Display Settings

You can configure various display options

such as the TV Aspect Ratio, Resolution, etc.

TV Aspect Ratio

Depending on the type of television you have,

you may want to adjust the screen size setting.

✎

NOTES

Depending on the disc type, some aspect

ratios may not be available.

If you select an aspect ratio and option which is

different than the aspect ratio of your TV screen,

the picture might appear to be distorted.

BD Wise (Samsung TVs only)

BD Wise is Samsung’s latest inter-connectivity

feature.

When you connect a Samsung player and a

Samsung TV with BD Wise to each other via

HDMI, and BD Wise is on in both the player

and TV, the player outputs video at the video

resolution and frame rate of the Blu-ray Disc/

DVDs.

✎

NOTES

When BD Wise is on, the Resolution setting

automatically defaults to BD Wise and BD Wise

appears in the Resolution menu.

If the player is connected to a device that does not

support BD Wise, you cannot use the BD Wise function.

For proper operation of BD Wise, set the BD

Wise menu of both the player and the TV to On.

SCREEN

VIEW A-B

FULLBONUS REPEATREPEAT

No Disc

Change Device

View Devices

Enter

Videos

App1 App2 App3

Photos Music Settings

6 1

02285B-01-BD-F5100-ZC-ENG.indd 9 2013-07-08 오후 2:22:35

Resolution

Lets you set the output resolution of the HDMI

video signal to Auto, 1080p, 1080i, 720p or

480p. The number indicates the number of

lines of video per frame. The i and p indicate

interlaced and progressive scan, respectively.

The more lines, the higher the quality.

Resolution according to the output

mode

• Blu-ray Disc/E-contents/Digital Contents

playback

Output

Setup

HDMI / connected

HDMI Mode

Blu-ray Disc

E-contents/

Digital

contents

BD Wise

Resolution of

Blu-ray Disc

1080p

Auto

Max. Resolution

of TV input

Max. Resolution

of TV input

1080p@60F

(Movie Frame : Off)

1080@60F 1080@60F

Movie Frame :

Auto (24Fs)

1080@24F 1080p@24F

1080i 1080i 1080i

720p 720p 720p

480p 480p 480p

• DVD playback

Output

Setup

HDMI / connected

HDMI Mode

BD Wise 480i

Auto Max. Resolution of TV input

1080p 1080p

1080i 1080i

720p 720p

480p 480p

✎

NOTES

If the TV you connected to the player does not

support Movie Frame or the resolution you

selected, the message "If no pictures are shown

after selecting ‘Yes’, please wait for 15 seconds

to return to the previous resolution. Do you

want to change the resolution?" appears. If you

select Yes, the TV’s screen will go blank for 15

seconds, and then the resolution will revert to

the previous resolution automatically.

If the screen stays blank after you have

changed the resolution, remove all discs,

and then press and hold the

button on the

front of the player for more than 5 seconds.

All settings are restored to the factory default.

Follow the steps on the previous page to

access each mode and select the Display Setup

that your TV will support.

When the factory default settings are restored,

all stored user BD data is deleted.

The Blu-ray Disc must have the 24 frame feature

for the player to use the Movie Frame (24Fs) mode.

Movie Frame (24Fs)

Setting the Movie Frame (24Fs) feature to

Auto allows you to adjust the player’s HDMI

output to 24 frames per second for improved

picture quality.

You can enjoy the Movie Frame (24Fs) feature

only on a TV supporting this frame rate.

You can select Movie Frame only when the

player is in the HDMI 1080i or 1080p output

resolution modes.

HDMI Color Format

Lets you set the color space format for

HDMI output to match the capabilities of the

connected device (TV, monitor, etc).

HDMI Deep Color

Lets you output video from the HDMI OUT jack with

Deep Color. Deep Color provides more accurate

color reproduction with greater color depth.

Progressive Mode

Lets you improve picture quality when viewing DVDs.

Audio Settings

Digital Output

Lets you select the digital audio output format that is suitable for your TV or AV Receiver. For

more details, please refer to the Digital Output Selection table below.

Digital Output Selection

Setup PCM

Bitstream

(Unprocessed)

Bitstream

(Re-encoded

DTS)

Bitstream

(Re-encoded

Dolby D)

Connection

HDMI

Receiver

Coaxial

HDMI

Receiver

Coaxial

HDMI Receiver or

Coaxial

HDMI supported

AV receiver or

Coaxial

Audio Stream

on Blu-ray

Disc

PCM Up to 7.1ch PCM 2ch PCM PCM 2ch Re-encoded DTS

Re-encoded

Dolby Digital *

Dolby Digital PCM 2ch PCM 2ch Dolby Digital Dolby Digital Re-encoded DTS

Re-encoded

Dolby Digital *

Dolby Digital Plus PCM 2ch PCM 2ch

Dolby Digital

Plus

Dolby Digital Re-encoded DTS

Re-encoded

Dolby Digital *

Dolby TrueHD PCM 2ch PCM 2ch Dolby TrueHD Dolby Digital Re-encoded DTS

Re-encoded

Dolby Digital *

DTS PCM 2ch PCM 2ch DTS DTS Re-encoded DTS

Re-encoded

Dolby Digital *

DTS-HD High

Resolution Audio

PCM 2ch PCM 2ch

DTS-HD High

Resolution

Audio

DTS Re-encoded DTS

Re-encoded

Dolby Digital *

DTS-HD Master

Audio

PCM 2ch PCM 2ch

DTS-HD

Master Audio

DTS Re-encoded DTS

Re-encoded

Dolby Digital *

Audio Stream

on DVD

PCM PCM 2ch PCM 2ch PCM 2ch PCM 2ch PCM 2ch PCM 2ch

Dolby Digital PCM 2ch PCM 2ch Dolby Digital Dolby Digital Dolby Digital Dolby Digital

DTS PCM 2ch PCM 2ch DTS DTS DTS DTS

Definition for

Blu-ray Disc

Any

Decodes main feature

audio and BONUSVIEW

audio stream together

into PCM audio and add

Navigation Sound Effects.

Outputs only main feature

audio stream so that your

AV receiver can decode the

audio bitstream.

You will not hear BONUSVIEW

audio and Navigation Sound

Effects.

Decodes main feature

audio and BONUSVIEW

audio stream together

into PCM audio

and add Navigation

Sound Effects, then

re-encodes the

PCM audio into DTS

bitstream

Decodes main

feature audio and

BONUSVIEW audio

stream together into

PCM audio and add

Navigation Sound

Effects, then re-

encodes the PCM

audio into Dolby

Digital bitstream

02285B-01-BD-F5100-ZC-ENG.indd 10 2013-07-08 오후 2:22:35

* If Source Stream is 2ch, "Re-encoded

Dolby D" Settings are not applied.

Blu-ray Discs may include three audio streams :

- Main Feature Audio : The audio soundtrack

of the main feature.

- BONUSVIEW audio : An additional

soundtrack such as the director or actor’s

commentary.

- Navigation Sound Effects : When you

choose a menu navigation selection, a

Navigation Sound Effect may sound.

Navigation Sound Effects are different on

each Blu-ray Disc.

✎

NOTES

Be sure to select the correct Digital Output or

you will hear no sound or just loud noise.

If the HDMI device (AV receiver, TV) is not

compatible with compressed formats (Dolby

Digital, DTS), the audio signal outputs as PCM.

Regular DVDs do not have BONUSVIEW audio

and Navigation Sound Effects.

Some Blu-ray Discs do not have BONUSVIEW

audio and Navigation Sound Effects.

If you play MPEG audio soundtracks, the audio

signal outputs as PCM regardless of your

Digital Output selections (PCM or Bitstream).

If your TV is not compatible with compressed

multi-channel formats (Dolby Digital, DTS), the

player may output PCM 2ch downmixed audio

even though you selected Bitstream (either Re-

encoded or Unprocessed) in the setup menu.

If your TV is not compatible with PCM sampling

rates over 48kHz, the player may output 48kHz

downsampled PCM audio even though you set

PCM Downsampling to Off.

PCM Downsampling

Lets you choose to have 96KHz PCM signals

downsampled to 48KHz before they are

outputted to an amplifier. Choose only if your

amplifier or receiver is not compatible with a

96KHz signal.

Dynamic Range Control

Lets you apply dynamic range control to

Dolby Digital, Dolby Digital Plus, and Dolby

True HD audio.

• Auto : Automatically controls the dynamic

range of Dolby TrueHD audio, based

on information in the Dolby TrueHD

soundtrack.

Also turns dynamic range control on for

Dolby Digital and Dolby Digital Plus.

• Off :

Leaves the dynamic range uncompressed,

letting you hear the original sound.

• On : Turns dynamic range control on for

all three Dolby formats. Quieter sounds

are made louder and the volume of loud

sounds is reduced.

Downmixing Mode

Lets you select the multi-channel downmix

method that is compatible with your stereo

system. You can choose to have the player

downmix to normal stereo or to surround

compatible stereo.

Network Settings

Please contact your ISP to find out if your IP

address is static or dynamic. If it is dynamic

- and most are - we recommend using the

Auto procedure for network setup. This is

easiest and will work in the majority of cases.

If it is static, you must use the manual set up

procedure.

Network setup directions start below.

✎

NOTES

This unit can only be connected to a Network

via a wired connection.

Wired Network Settings

1. In the Home menu, press the ◄►

buttons to select Settings, and then

press the

button.

2. Press the ▲▼ buttons to select

Network, and then press the

button.

3. Press the ▲▼ buttons to select Wired

Network Settings, and then press the

button. The Wired Network Settings

screen appears.

4. In the Internet Protocol Setup field,

select Auto if it is not selected. (Press

to select Auto, and then press

5. The Auto Function acquires and fills

in the values for IP Address, Subnet

Mask, etc., automatically.

✎

NOTES

This process can take up to five minutes.

6. After the Network Function has acquired

the network values, press the RETURN

button.

7. Select Network Test, and then press

to ensure the player has connected

to your network.

8. When the Network Test is complete,

press the RETURN twice to return to

the Main Menu.

9. If the Network Function does not acquire

the network values, go to the directions

for Manual Setup.

Manual Network Setup

Before you start manual network setup, you

need the network setting values.

To get the network setting values, contact

your ISP (Internet Service Provider) or your

network administrator.

To enter the Network Settings into your

player, follow these steps:

1. In the Home menu, press the ◄►

buttons to select Settings, and then

press the

button.

2. Press the ▲▼ buttons to select

Network, and then press the

button.

Display

Audio

Network

System

Language

Security

General

Support

Settings

Wired Network Settings

Internet Protocol Setup : Auto

IP Address :

Subnet Mask :

Gateway :

DNS : Auto

DNS Server :

Move

Select

Return

02285B-01-BD-F5100-ZC-ENG.indd 11 2013-07-08 오후 2:22:36

3. Press the ▲▼ buttons to select Wired

Network Settings, and then press the

button. The Wired Network Settings

screen appears.

4. Select the Internet Protocol Setup field,

and then press the

button.

5. Press the ▲▼ buttons to select Manual,

and then press the

button.

6. Press the ▼ button to go to the first

entry field (IP Address).

7. Use the number buttons on your remote

to enter numbers.

8. When done with each field, use the ►

button to move to the next field. You

can also use the other arrow buttons to

move up, down, and back.

9. Enter the IP Address, Subnet Mask,

and Gateway values in the same way.

10. Press the ▼ button to go to DNS.

11. Press the ▼ button to go to the first

DNS entry field.

12. Enter the numbers as above.

13. Press the RETURN button on your

remote control.

14. Run a Network Test to ensure the player

has connected to your network.

Network Test

Use this menu item to check whether your

network connection is working or not.

Network Status

Use to check whether a connection to a

network and the Internet has been established.

BD-Live Internet Connection

Set to allow or prohibit an Internet connection

when you use the BD-LIVE service.

• Allow (All) : The Internet connection is

allowed for all BD-LIVE contents.

• Allow (Valid Only) : The Internet

connection is allowed only for BD-LIVE

contents containing a valid certificate.

• Prohibit : No Internet connection is allowed

for any BD-LIVE content.

✎

NOTES

What is a valid certificate?

When the player uses BD-LIVE to send the

disc data and a request to the server to certify

the disc, the server uses the transmitted data

to check if the disc is valid and sends the

certificate back to the player.

The Internet connection may be restricted

while you are using BD-LIVE contents.

Using BD-LIVE™

Once the player is connected to the network,

you can enjoy various movie-related service

contents using a BD-LIVE compliant disc.

1. Attach a USB memory stick to the

USB jack on the front of the player, and

then check its remaining memory. The

memory device must have at least 1GB

of free space to accommodate the BD-

LIVE services.

2. Insert a Blu-ray Disc that supports BD-

LIVE.

3. Select an item from various BD-LIVE

service contents provided by the disc

manufacturer.

✎

NOTES

The way you use BD-LIVE and the provided

contents may differ, depending on the disc

manufacturer.

The DLNA Function

DLNA lets you play music, video, and photo

files located in your PC or NAS on the player.

To use DLNA with your player, you must

connect the player to your network.

(See pages 11~12).

To use DLNA with your PC, you must install

DLNA software on your PC.

If you have NAS, you can use DLNA without

any additional software.

To download DLNA software

1. Go to Samsung.com

2. Click Support, enter your player’s

product number in the field that

appears, and then click Product.

3. On the next screen, click Get downloads

under Downloads.

4. Click Software on the next page.

5. Click the icon in the DLNA line under File

to start the download.

For instructions explaining how to play content

located on your PC, see pages 15~16.

System Settings

Initial Settings

By using the Initial Settings function, you can

set the language, Network Settings, etc.

For more information about the Initial Settings

function, refer to the Initial Settings section of

this user manual (page 9).

Quick Start

You can turn on the power quickly by

decreasing the boot time.

✎

NOTES

If this function is set to On, Standby power

consumption will be increased.

Anynet+ (HDMI-CEC)

Anynet+ is a convenient function that offers

linked operations with other Samsung players

that have the Anynet+ feature.

To operate this function, connect this player to

an Anynet+ Samsung TV with an HDMI cable.

With Anynet+ on, you can operate this player

using a Samsung TV remote control and start

disc playback simply by pressing the PLAY

( ) button on the TV’s remote control.

For more information, please see the TV user

manual.

✎

NOTES

This function is not available if the HDMI cable

does not support CEC.

If your Samsung TV has an Anynet+ logo, then

it supports the Anynet+ function.

Depending on your TV, certain HDMI output

resolutions may not work.

Please refer to the user manual of your TV.

02285B-01-BD-F5100-ZC-ENG.indd 12 2013-07-08 오후 2:22:36

If you have Anynet+ turned on, when you

turn off the product, disconnect, and then

reconnect the power cable, the product turns

on automatically to re-establish the Anynet+

connection. After about 15 seconds, it turns off

again automatically.

Some Samsung TVs, when connected to this

product using the Anynet+ function will, when

you turn them on, display a warning popup

message saying no connection has been

found. Never-the-less, the Anynet+ connection

is properly established and available to use.

BD Data Management

Enables you to manage the downloaded

contents you accessed through a Blu-ray disc

that supports the BD-LIVE service and stored

on a flash drive.

You can check the device’s information

including the storage size, delete the BD data,

or change the Flash memory device.

✎

NOTES

In the external memory mode, disc playback

may be stopped if you disconnect the USB

device in the middle of playback.

Your player supports the FAT16, FAT32, and

NTFS file systems. We recommend you use

USB devices that support USB 2.0 protocol

with 4 MB/sec or faster read/write speed.

The Resume Play function may not work after

you format the storage device.

The total memory available to BD Data

Management may differ, depending on the

conditions.

Language Settings

You can select the language you prefer for the

Home menu, disc menu, audio, and subtitles.

✎

NOTES

The selected language will only appear if it is

supported on the disc.

Security Settings

When you access this function for the first

time, the PIN screen appears. Enter the

default PIN - 0000 - using the number

buttons. To change the PIN, use the Change

PIN function (page 13). Each time you access

the Security Settings hereafter, you must

enter that four digit PIN. If you don’t change

the PIN, continue using the default PIN.

BD Parental Rating

Prevents playback of Blu-ray Discs with

specific age ratings unless the 4 digit PIN is

entered.

DVD Parental Rating

This function works in conjunction with DVDs

that have been assigned an age rating or

numeric rating that indicates the maturity level

of the content. These numbers help you control

the types of DVDs that your family can watch.

Select the rating level you want to set.

For example, if you select Level 6, discs rated

above 6 - Level 7 and 8 - will not play.

A larger number indicates more mature content.

When the DVD Parental Rating function is on,

you must enter the 4 digit PIN to play discs

with restricted rating levels.

Change PIN

Change the 4-digit password used to access

security functions.

To change the PIN, follow these steps:

1. Select Change PIN, and then press the

button. The Enter old PIN screen

appears.

2. Enter the old PIN. If you never changed

the PIN, enter the default PIN: 0000.

The Enter new PIN screen appears.

3. Enter the new PIN in the Enter new PIN

fields.

4. Re-enter the new PIN in the Confirm

new PIN fields. The "PIN is changed

successfully." message appears.

5. Press the

button.

If you forget your password

1. Remove any discs.

2. Press and hold the

button on the

front panel for 5 seconds or more.

All settings will revert to the factory settings.

✎

NOTES

When the factory default settings are restored,

all the user stored BD data will be deleted.

General Settings

Time Zone

Lets you specify the time zone that is

applicable to your area.

Support Settings

Software Upgrade

The Software Upgrade menu allows you to

upgrade the player’s software for performance

improvements or additional services.

By Online

To upgrade By Online, follow these steps:

1. Select By Online, and then press the

button. The Connecting to Server

message appears.

2. A popup message will appear if an

update is available.

3. If you select Yes, the player will turn off

automatically before restarting.

(Never turn the player on or off manually

during an upgrade.)

4. The update progress popup will appear.

When the update is completed, the

player will turn off automatically.

5. Press the POWER button to turn on the

player.

✎

NOTES

The Update is complete when the player turns

off after restarting. Press the POWER button to

turn on the updated player for your use.

Never turn the player off or back on manually

during the update process.

Samsung Electronics takes no legal

responsibility for player malfunction caused by

an unstable Internet connection or consumer

negligence during a software upgrade.

02285B-01-BD-F5100-ZC-ENG.indd 13 2013-07-08 오후 2:22:36

By USB

To upgrade by USB, follow these steps:

1. Visit www.samsung.com/bluraysupport.

2. Download the latest USB software

upgrade zip archive to your computer.

3. Unzip the zip archive to your computer.

You should have a single RUF file with

the same name as the zip file.

4. Copy the RUF file to a USB flash drive.

5. Make sure there is no disc in the player,

and then insert the USB flash drive into

the USB port of the player.

6. In the player’s menu, go to Settings >

Support > Software Upgrade.

7. Select By USB.

✎

NOTES

No disc should be in the product when you

upgrade the software using the USB Host jack.

When the software upgrade is done, check the

software details in the software Upgrade menu.

Do not turn off the player during the software

upgrade. It may cause the player to malfunction.

Software upgrades using the USB Host jack

must be performed with a USB flash memory

stick only.

Auto Upgrade Notification

If you have connected the player to your

network, and then set Auto Upgrade

Notification on, the player automatically

notifies you when a new software version is

available for the player.

To set Auto Upgrade Notification on, follow

these steps:

1. Select Auto Upgrade Notification, and

then press the

button.

2. Use the ▲▼ buttons to select On, and

then press the

button.

If there is a new software version available,

the player notifies you with a popup message.

1. To upgrade the firmware, select Yes

in the Pop-up. The player turns off

automatically, then restarts, and begins

the download. (Never turn the player on

or off manually during an upgrade.)

2. The update progress popup appears.

3. When the update is complete, the player

turns off again automatically.

4. Press the POWER button to turn on the

player.

✎

NOTES

The update is complete when the player turns

off after restarting. Press the POWER button to

turn on the updated player for your use.

Never turn the player off or on manually during

the update process.

Samsung Electronics takes no legal

responsibility for player malfunction caused by

an unstable Internet connection or consumer

negligence during software upgrade.

Media Play

Playing a Commercially Recorded

Disc

1. Press the

button to open the disc

tray.

2. Place a disc gently into the disc tray

with the disc's label facing up.

3. Press the

button to close the disc

tray. Playback starts automatically.

Playing Files on a USB Device

You can play multimedia files located on a

USB storage device.

1. Move to the Home menu.

2. In Stop mode, connect the USB storage

device to the USB port on the front

panel of the player.

The message "Do you want to access

the device?" is displayed.

3. Press the ◄► button to select Yes, and

then press the

button.

4. If you have a disc in the Blu-ray player,

press the RED (A) or BLUE (D) button.

If you do not, go to Step 6.

If you pressed the RED (A) button, go to

Step 5.

If you pressed the BLUE (D) button, go

to Step 5

-1

5. Press the ▲▼ buttons to select USB,

and then press the

button.

Contact Samsung

Provides contact information for assistance

with your player.

Lets you view the general disclaimer regarding

third party contents and services.

Reset

Returns all settings to their factory defaults

except for the network settings.

02285B-01-BD-F5100-ZC-ENG.indd 14 2013-07-08 오후 2:22:37

6. Press the ◄► buttons to select Videos,

Music, or Photos, and then press the

button. Go to Step 7.

-1

. Press the ◄► buttons to select USB,

then press the

button.

-1

. Press the ▲▼ buttons to select Videos,

Music or Photos, and then press the

button.

7. A screen appears listing the contents

of the device. Depending on how the

contents are arranged, you will see

either folders, individual files, or both.

8. If necessary, use the ▲▼◄►buttons to

select a folder, and then press the

button.

9. Use the ◄►▲▼ buttons to select a file

to view or play, and then press the

button.

✎

NOTES

Even though the player will display folders for

all content types, it will only display files of the

Content Type you selected in Step 6 or Step

6-1.

For example, if you selected music, you will

only be able to see music files. You can change

this selection by returning to the Home screen

and following the directions from Step 4.

10. Press the RETURN button one or more

times to exit a current screen, exit a

folder, or to return to the Home screen.

Press the EXIT button to return directly

to the Home Screen.

11. The controls and tools you use to

control and play videos, music, and

pictures located on a USB device are

identical to those you use to play videos,

music, and pictures on a disc.

Go to pages 15~17 for instructions.

✎

NOTES

You must remove the USB storage device

safely by performing the "Safely Remove USB"

function in order to prevent possible damage

to the USB memory. Press the MENU button to

move to the Home menu, select the YELLOW

button.

If you insert a disc when playing a USB storage

device, the device mode changes to Blu-ray,

DVD or CD automatically.

Playing a Disc with User Recorded

Content

You can play multimedia files you have

recorded on Blu-ray, DVD, or CD discs.

1. Place a user recorded disc into the

disc tray with the disc’s label facing

up, and then close the tray. The Device

Connected pop-up appears.

2. Use the ◄► buttons to select the type

of content you want to view or play -

Videos, Photos, or Music - and then

press the

button.

✎

NOTES

Even though the player will display folders for

all content types, it will only display files of

the Content Type you selected in Step 2. For

example, if you selected music, you will only

be able to see music files. You can change this

selection by returning to the Home screen and

repeating Step 2.

3. A screen appears listing the contents

of the disc. Depending on how the

contents are arranged, you will see

either folders, individual files, or both.

4. If necessary, use the ▲▼◄►buttons to

select a folder, and then press the

button.

5. Use the ◄►▲▼ buttons to select a file

to view or play, and then press the

button.

6. Press the RETURN button one or more

times to exit a current screen, exit a

folder, or to return to the Home screen.

Press the EXIT button to return directly

to the Home Screen.

7. Go to pages 15~17 for instructions

that explain how to control playback of

videos, music, and pictures on a disc.

Playing Content Located in Your PC

To play content located in your PC on your

Blu-ray disc player, you must connect the

Blu-ray player to you network. (See pages

11~12.) and install DLNA Software on your

PC.

To Play Content From Your PC

1. Go to the Home Menu.

2. Press the BLUE (D) button on your

remote (Device).

3. In the Device screen that appears, select

your PC, and then press the

button.

4. Use the ◄► buttons to select the type

of content you want to view or play -

Videos, Photos, or Music - and then

press the

button.

✎

NOTES

Even though the player will display folders for

all content types, it will only display files of

the Content Type you selected in Step 4. For

example, if you selected music, you will only

be able to see music files. You can change this

selection by returning to the Home screen and

repeating Step 4.

5. A screen appears listing the contents

on your PC. Depending on how the

contents are arranged, you will see

either folders, individual files, or both.

6. If necessary, use the ▲▼◄►buttons to

select a folder, and then press the

button.

7. Use the ◄►▲▼ buttons to select a file

to view or play, and then press the

button.

123

Change Device

Safely Remove USB

View Devices

Enter

Videos

1 App2 App3

Photos Music Settings

No Disc

123

Home

Enter

123

App1 App2 App3

a Settings

02285B-01-BD-F5100-ZC-ENG.indd 15 2013-07-08 오후 2:22:38

button

Starts playback.

button

Stops playback.

button

Pauses playback.

Fast Motion

Play

During playback, press the

button.

Each time you press the

button, the playback speed

will change.

Slow Motion

Play

In pause mode, press the

button.

Each time you press the

button, the playback speed will

change.

Step Motion

Play

In pause mode, press the

button.

Each time you press the

button, a new frame appears.

Skip Motion

Play

During playback, press the

button.

Each time you press the

button, the disc moves to the

previous or next chapter or file.



Using the disc menu, title menu,

popup menu, and title list

DISC MENU

button

During playback, press this button

to start the disc menu function.

TITLE MENU

button

During playback, press this button

to start the title menu function.

POPUP MENU

button

During playback, press this button

to start the popup menu function.

Controlling Music Playback

You can control the playback of music located

on a Blu-ray disc, DVD, CD, USB device, or

your computer.

Buttons on the Remote Control

used for Music Playback

NUMBER buttons (Audio CD (CD-DA) only) :

During Playlist playback, press the desired

track number.

The selected track is played.

Skip : During playback, press the

button to move to the previous or next file of

the playlist.

button : Stops a track.

Fast Play (Audio CD (CD-DA) only)

During playback, press the

button.

Each time you press the

button,

the playback speed will change.

Pause : Pauses a track.

button : Plays the currently selected

track.

Repeat an Audio CD (CD-DA)/

MP3

1. During Playlist playback, press the

TOOLS button.

2. Press the ◄► buttons to select Track,

All, Shuffle, or Off.

3. Press the

button.

Off

Songs are played in the order

in which they were recorded.

(

) Track The current song is repeated.

(

) All All songs are repeated.

(

) Shuffle

Shuffle plays songs in random

order.

8. Press the RETURN button one or more

times to exit a current screen, exit a

folder, or to return to the Home screen.

Press the EXIT button to return directly

to the Home Screen.

9. Go to pages 15~17 for instructions

that explain how to control playback of

videos, music, and pictures on a PC.

Controlling Video Playback

You can control the playback of video content

located on a Blu-ray disc, DVD, CD, USB

device, or you computer. Depending on the

media, some of the functions described in this

manual may not be available.

During Blu-ray or DVD disc playback, the Full

screen button does not operate.

Buttons on the Remote Control

used for Video Playback



Playback related buttons

The player does not play sound in Search,

Slow or Step mode.

• To return to normal speed playback, press

the

button.

SCREEN

VIEW A-B

FULLBONUS REPEATREPEAT

Pause Tools

Return

00:08 / 05:57

1/6

TRACK 001