Washing Machine
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/register
WF419AAW
BEST-WF419AAW-02657A_EN.indd 1 2009-02-18 ¿ÀÈÄ 3:26:39
2_ Features of your new VRT™ STEAM washer
features of your new VRT™
STEAM washer
1. VRT™ (Vibration Reduction Technology)
This Samsung washer performs smoothly at top spin speeds, minimizing noise and vibration.
2. Super capacity
Samsung’s extra-large capacity laundry machine can wash a full set of your bedding, a king-
size comforter, or up to 26 bath towels in a single load. Since you don’t have to do as many
loads, you save time, money, water and energy.
3. Deep steam
The deep steam feature boosts cleaning performance and loosens grime and dirt, thus
providing superior cleaning results.
4. Diamond drum™
Take gentle care of your fabrics. With inside holes 36% smaller than those of conventional
drums, the diamond drum prevents fabrics from sticking out and consequently being
damaged.
5. Stylish design
The stylish design of this washer blends well with your environment.
6. Display & Center jog dial
The jog dial enables you to select cycles in both directions with ease, and the display is easy
to use and understand.
7. DD Motor
The power to handle anything! Our direct-drive inverter motor delivers power right to the
washer tub from a variable speed, reversible motor. A beltless direct-drive motor generates a
higher spin speed of 1,200rpm for more effective, quiet operation. The washer also has fewer
moving parts, meaning fewer repairs.
8. Sanitize
When selecting this cycle, the water heats to an extra high temperature to remove 99.9% of
certain bacteria typically found on clothing, bedding, or towels. This certification is conducted
by NSF International, an independent third-party testing and certification organization.
Please check garment care label to avoid garment damage. Only sanitizing cycles have been
designed to meet the requirements of this protocol for sanitization efficacy.
NSF Protocol P172
Sanitization Performance of Residential and
Commercial, Family-Sized Clothes Washers
BEST-WF419AAW-02657A_EN.indd 2 2009-02-18 ¿ÀÈÄ 3:26:40
Features of your new VRT™ STEAM washer _3
9. Pedestal with storage drawer
(Model No : WE357A7P/E/W/R)
An optional 15in.(38.1cm) pedestal is available to raise the washer for easier loading and
unloading.
It also offers a built-in storage drawer that can hold a 100 oz. bottle of detergent
10. Stacking (Model No : SK-3A1/XAA , SK-4A/XAA , SK-5A/XAA)
Samsung washer and dryer can be stacked to maximize usable space. An optional stacking
kit is available for purchase from your Samsung retailer.
<Pedestal with Storage Drawers> <Stacking>
BEST-WF419AAW-02657A_EN.indd 3 2009-02-18 ¿ÀÈÄ 3:26:40
4_ Safety information
safety information
Congratulations on your new Samsung ActivFresh™ washer. This manual
contains important information on the installation, use and care of your
appliance. Please take time to read this manual to take full advantage of your
washer’s many benefits and features.
WHAT YOU NEED TO KNOW ABOUT SAFETY INSTRUCTIONS
Warnings and Important Safety Instructions in this manual do not cover all possible conditions and
situations that may occur. It is your responsibility to use common sense, caution, and care when installing,
maintaining, and operating your washer.
IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS
WARNING
Hazards or unsafe practices that may result in severe personal injury or
death.
CAUTION
Hazards or unsafe practices that may result in minor personal injury or
property damage.
CAUTION
To reduce the risk of fire, explosion, electric shock, or personal injury when
using your washer, follow these basic safety precautions:
Do NOT attempt.
Do NOT disassemble.
Do NOT touch.
Follow directions explicity.
Unplug the power plug from the wall socket.
Make sure the machine is grounded to prevent electric shock.
Call the service center for help.
Notice
Read all instructions before using the appliance.
With any equipment using electricity and moving parts, potential hazards exist.
To safely operate this appliance, become familiar with its operation and be careful when
using it.
Install and store your washer inside, away from exposure to weather.
Install and level your washer on a floor that can support its weight.
Your washer must be properly grounded. Never plug it into an ungrounded outlet. See page
8 for more information on grounding your washer.
BEST-WF419AAW-02657A_EN.indd 4 2009-02-18 ¿ÀÈÄ 3:26:40
Safety information _5
To reduce the risk of fire or explosion:
• Do not wash items that have been washed, soaked, or treated with gasoline, dry
cleaning solvents, or other flammable or explosive substances. They give off vapors that
could ignite or explode. Rinse by hand any material that has been exposed to cleaning
solvent or other flammable liquids or solids before putting in your washer. Be sure that
all traces of such liquids, solids, and fumes have been removed. Dangerous substances
include acetone, denatured alcohol, gasoline, kerosene, certain liquid household
cleaners and spot removers, turpentine, waxes, and wax removers.
• Do not put gasoline, dry cleaning solvents, or other flammable or explosive substances
into the washer.
• Under certain conditions, hydrogen gas may be produced in a hot water system–such
as your hot water heater-- that has not been used for two weeks or more. HYDROGEN
GAS IS EXPLOSIVE. If your hot water system has not been used for two weeks or
more, turn on all hot water faucets in your home, and let the water flow for several
minutes before using your washer. This will release any hydrogen gas build–up. Since
hydrogen gas is flammable, do not smoke or light an open flame during this time.
Unplug the power cord before servicing your washer.
Do not reach into the appliance when the tumbler is moving.
Do not let children play on or in your washer. The washer door isn’t easily opened from the
inside, and a child could be seriously injured if trapped inside.
Do not tamper with the controls.
Do not repair, replace, or service any part of your washer yourself unless you fully
understand the recommended user–repair instructions and have the skills to carry them
out. Work done by an unauthorized person may void your warranty.
Store laundry detergents and other laundry supplies in a cool, dry place out of children’s
reach.
Do not wash or dry items that are soiled with vegetable or cooking oil. These items may
contain some oil after laundering. Due to the remaining oil, the fabric may smoke or catch
fire by itself.
Do not use chlorine bleach, ammonia, or acids (such as vinegar or rust remover) in the
same wash. Hazardous fumes can form.
Do not wash fiberglass materials. Small particles can stick to fabrics washed in subsequent
loads and cause skin irritation.
Before disposing of your washer, remove the door so that children or small animals cannot
get trapped inside.
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety.
Children should be supervised to ensure that they do not play with the appliance.
Do not sit on top of your washer.
Inlet hoses are subject to damage and deterioration over time. Check the hoses periodically
for bulges, kinks, cuts, wear or leaks, and replace them every five years.
Ensure pockets are free from small irregularly shaped hard objects, foreign materials such
as coins, knives, pins, etc. These objects could damage your washer.
Do not wash clothing with large buckles, buttons, or other heavy metal.
WARNING
WARNING
WARNING
WARNING
WARNING
BEST-WF419AAW-02657A_EN.indd 5 2009-02-18 ¿ÀÈÄ 3:26:41
6_ Contents
contents
INSTALLING YOUR WASHER
7
7 Unpacking your washer
7 Overview of your washer
8 BASIC LOCATION REQUIREMENTS
8 Electrica
l
8 Groundin
g
8 Wate
r
9 Drain facilit
y
9 Floorin
g
9 Location consideratio
n
9 Alcove or closet installatio
n
10 Important note to installer
OPERATING INSTRUCTIONS
13
13 Loading your washer
13 Getting started
WASHING A LOAD OF LAUNDRY
14
14 Overview of the control panel
16 Child loc
k
16 Garment
+
16 My cycl
e
17 Washing clothes using the cycle selecto
r
18 For ActivFresh™ washing
18 Using steam wash
19 Detergent use
19 Features
MAINTAINING YOUR WASHER
21
21 Cleaning the exterior
21 Cleaning the interior
21 Cleaning the dispensers
21 Storing your washer
22 Cleaning the debris filter
22 Preserving the top cover and the front frame
TROUBLESHOOTING
23
23 Check these points if your washer…
25 Information codes
APPENDIX
27
27 Fabric care chart
28 Cycle chart
29 Helping the environment
29 Declaration of conformity
29 Specification
WARRANTY
30
30 Warranty
BEST-WF419AAW-02657A_EN.indd 6 2009-02-18 ¿ÀÈÄ 3:26:41
Installing your washer _7
installing your washer
UNPACKING YOUR WASHER
Unpack your washer and inspect it for shipping damage. Make sure you have received all of the items
shown below. If your washer was damaged during shipping, or you do not have all of the items, contact
1-800-SAMSUNG(726-7864).
To prevent personal injury or strain, wear protective gloves whenever lifting or carrying the unit.
Packing materials can be dangerous to children; keep all packing material (plastic bags, polystyrene,
etc.) well out of the reach of children.
OVERVIEW OF YOUR WASHER
Parts Supplied
Wrench Bolt Hole Covers Water Supply Hoses Rubber Washers
Hose Guide Plastic Zip Hose Tie Manual Book
Tools Needed
Pliers Flat screwdriver
01 Installing your washer
WARNING
Adjustable legs
Cold water supply
hose
Hot water supply
hose
Drain Hose
Detergent drawer
Control panel
Door
Tub
Debris filter
Drain tube
Filter cover
Power
code(plug)
BEST-WF419AAW-02657A_EN.indd 7 2009-02-18 ¿ÀÈÄ 3:26:42
8_ Installing your washer
BASIC LOCATION REQUIREMENTS
Electrical
• 120 Volt 60 Hz 15 AMP fuse or circuit breaker
• Individual branch circuit serving only your washer is recommended.
• Your washer is equipped with a power cord.
Never use an extension cord.
Grounding
ELECTRICAL GROUNDING IS REQUIRED ON THIS APPLIANCE.
This appliance must be grounded. In the event of malfunction or breakdown, grounding will
reduce the risk of electric shock by providing a path of least resistance for electric current.
This appliance is equipped with a power cord having a three-prong grounding plug for use in a
properly installed and grounded outlet.
Improper connection of the equipment-grounding conductor can result in a risk of electrical
shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the
appliance is properly grounded. Do not modify the plug provided with the appliance – if it
does not fit the outlet, have a proper outlet installed by a qualified electrician.
IMPORTANT SAFETY PRECAUTIONS
• To prevent unnecessary risk of fire, electrical shock or personal injury, all wiring and
grounding must be done in accordance with the National Electrical Code ANSI/FNPA, No.
70 Latest Revision and local codes and ordinances. It is the personal responsibility of the
appliance owner to provide adequate electrical service for this appliance.
Never connect ground wire to plastic plumbing lines, gas lines, or hot water pipes.
Water
To correctly fill your washer in the proper amount of time, water pressure of 20-116psi(137-
800kPa) is required.
Water pressure less than 20 psi(137kPa) may cause water valve failure, or may not allow the
water valve to shut off completely. Or, it may extend the fill time beyond what your washer
controls allow, resulting in your washer turning off. A time limit is built into the controls in the
event of an internal hose becoming loose and flooding your home.
The water faucets must be within 4 ft.(122cm) of the back of your washer for the inlet hoses
provided with your washer.
Accessory inlet hoses are available in various lengths up to 10 ft.(305cm) for faucets that
are further away from the back of your washer.
To avoid the possibility of water damage:
• Have water faucets easily accessible.
• Turn off faucets when the washer is not in use.
• Periodically check that there is no leakage from the water inlet hose fittings.
Check all connections at the water valve and faucet for leaks.
installing your washer
WARNING
WARNING
WARNING
WARNING
BEST-WF419AAW-02657A_EN.indd 8 2009-02-18 ¿ÀÈÄ 3:26:43
Installing your washer _9
Drain facility
The recommended height of the standpipe is 18 in (46 cm). The drain hose must be routed
through the drain hose clip to the standpipe. The standpipe must be large enough to accept the
outside diameter of the drain hose. The drain hose is attached at the factory.
Flooring
For best performance, your washer must be installed on a solidly constructed floor. Wood floor
may need to be reinforced to minimize vibration and/or unbalanced load situations. Carpeting
and soft tile surfaces are contributing factors in vibration and may cause your washer to move
slightly during the spin cycle.
Never install your washer on a platform or weakly supported structure.
Location consideration
Do not install your washer in areas where water may freeze, since your washer will always
maintain some water in its water valve, pump, and hose areas. This can cause damage the belts,
the pump, hoses and other components.
Alcove or closet installation
MINIMUM CLEARANCES FOR CLOSET AND ALCOVE INSTALLATIONS:
Sides – 1 In.(2.5 cm)
Rear – 4 In.(10.2 cm)
Top – 17 In.(43.2 cm)
Closet Front – 2 In.(5.1 cm)
If the washer and dryer are installed together, the closet front must have at least 72 in²(465 cm²)
of an unobstructed air opening. Your washer alone does not require a specific air opening.
01 Installing your washer
CAUTION
BEST-WF419AAW-02657A_EN.indd 9 2009-02-18 ¿ÀÈÄ 3:26:43
10_ Installing your washer
installing your washer
IMPORTANT NOTE TO INSTALLER
Please read the following instructions carefully before installing your washer.
These instructions should be retained for future reference.
We recommend you hire a professional for installation of this washer.
STEP 1
Removing the Shipping Bolts
Before using your washer, you must remove the four
shipping bolts from the back of the unit.
1. Loosen all the bolts with the supplied wrench.
2. Slide the bolt and spacer up and remove the bolt with
the spacer through the hole in the rear wall of your
washer. Repeat for each bolt.
3.
Fill the holes with the supplied bolt hole covers (page 7).
4. Keep the shipping bolts and spacers for future use.
STEP 2
Selecting a Location
Before you install your washer, make sure the location:
• Has a hard level surface.
• Is away from direct sunlight.
• Has adequate ventilation.
• Will not freeze (below 32°F or 0°C).
• Is away from heat sources such as oil or gas.
• Has enough slack for the power cord.
• Doesn’t have any carpeting that will obstruct ventilation openings.
BEST-WF419AAW-02657A_EN.indd 10 2009-02-18 ¿ÀÈÄ 3:26:43
Installing your washer _11
STEP 3
Installing your Washer
1.
Place the drain hose in the drain facility. Be
sure an airtight connection is NOT made
between the drain hose and the standpipe.
The standpipe must be at least 18in.(46
cm) high.
Caution must always be exercised to
avoid collapsing or damaging the drain
hose. For best results, the drain hose
should not be restricted in any way – by
elbows, couplings, or excessive lengths.
For situations where the drain hose
cannot be conveniently elevated to at
least 18in.(46 cm), the drain hose must
be supported.
2. Insert a new rubber washer (supplied) into each end of the
inlet hoses. Firmly seat the washers in the couplings.
3. Check the inlet hose to ensure a washer is inside each fill
hose.
Thread the inlet hoses to the HOT and COLD faucet
connections.
On the other end of the hose, check for one rubber washer
per hose and install each fill hose to the water valve. Make
sure the hose with the Hot printed line is attached to the
HOT faucet. Tighten by hand until snug, then two-thirds of a
turn with pliers.
For correct water use, connect both HOT and COLD water
valves. If either or both are not connected, an “nF” (no fill)
error can occur.
4. Turn on the “HOT” and “COLD “water supply and check all
connections at the water valve and the faucet for leaks.
01 Installing your washer
Cold Hot
Cold printed Hot printed
Rubber
Washer
Rubber
Washer
96” Max
18” Min
96” Max
18” Min
Hose
retainer
Tie
strap
Laundry tub Stand pipe
Hose
Guide
BEST-WF419AAW-02657A_EN.indd 11 2009-02-18 ¿ÀÈÄ 3:26:45
12_ Installing your washer
installing your washer
5. Plug the power cord into a 3-prong, well grounded 120 volt
60 Hz approved electrical outlet protected by a 15-amp
fuse or comparable circuit breaker.
Your washer is grounded through the third prong of the
power cord when plugged into a three-prong grounded
receptacle.
6. Slide your washer into position.
7. Level your washer by turning the leveling legs in or out as
necessary by hand or by using the wrench included with
your washer.
When your washer is level, tighten the locking nuts using
the wrench or (-) flathead screwdriver.
Your washer must be leveled on all four sides. A
carpenter’s level should be used on all four corners of
your washer. It’s a good idea after the first dozen washes
to recheck your washer’s levelness.
Avoid damage to the legs. Do not move
the washer unless the locking-nuts are
fastened to the bottom of the washer.
Levelling
Leg
Locking
Nut
BEST-WF419AAW-02657A_EN.indd 12 2009-02-18 ¿ÀÈÄ 3:26:46
Operating instructions _13
operating instructions
LOADING YOUR WASHER
• You can fill the tub with dry, unfolded clothes; but DO NOT OVERLOAD the tub.
• Overloading may reduce washing efficiency, cause excess wear, and possibly cause creasing or
wrinkling of the load.
• Wash delicate items such as bras, hosiery, and other lingerie in the delicates cycle with similar
lightweight items.
• When washing big bulky items or a few smaller items that don’t fill the tub completely – a rug, a pillow,
stuffed toys, or one or two sweaters, for example – add a few towels to improve tumbling and spin
performance.
During the spin cycle, the washer may add additional water to redistribute the excessive imbalance
inside the drum.
•
When washing heavily soiled loads, do not overload your washer in order to assure good cleaning results.
• To add a forgotten item:
1. Press the Power button.
2. Press the Start/Pause button.
3. Wait for the door lock light to go out (Immediately).
4. Add the item, close the door, and press the Start/Pause button.
The door safety state continues for 15 seconds and the cycle is restarted.
To ensure thorough cleaning, add items within five minutes of starting the wash cycle.
Try washing bedding, towels, undergarments, and other articles that usually have close body
contact using the ActivFresh™ Option, which sanitizes using cold water.
GETTING STARTED
1. Load your washer.
2. Close the door.
Push the laundry into the drum completely to prevent the laundry from being caught in the door or
from falling out of the drum.
3. Press the Power button.
4. Add detergent and additives to the dispenser (page 20~21).
5. Select the appropriate cycle and options for the load (page 14~16).
6. Press the Start/Pause button.
7. The Wash Indicator light will illuminate.
8. The estimated cycle time will appear in the display.
The time may fluctuate to better indicate the time remaining in the cycle.
The actual time required for a cycle may differ from the estimated time in the display depending on the
water pressure, water temperature, detergent, and laundry.
9. Before your washer starts to fill, it will make a series of clicking noises to check the door lock and do a
quick drain.
• When the cycle is complete, the door lock light will go out and “End” will appear in the display.
• DO NOT attempt to open the door until the door lock light is off. To add a forgotten item, see
“Loading your washer” section (page 13).
• When your washer is restarted after a pause, expect a delay of up to 15 seconds before the cycle
continues.
• Pressing Power button cancels the cycle and stops your washer.
•
The pre wash, wash, rinse and spin indicator lights will illuminate during those portions of the cycle.
02 Operating instructions
CAUTION
BEST-WF419AAW-02657A_EN.indd 13 2009-02-18 ¿ÀÈÄ 3:26:46
14_ Washing a load of laundry
washing a load of laundry
OVERVIEW OF THE CONTROL PANEL
Cycle Selector
Select the appropriate cycle for the type of load.
This will determine the tumble pattern and spin speed for the cycle.
To minimize wrinkling of your laundry, select the perm press cycle.
Normal - For most fabrics including cottons, linens, and normally soiled garments.
Heavy Duty - For sturdy, colorfast fabrics and heavily soiled garments.
Perm Press - For wash-and-wear, synthetic fabrics, and lightly to normally
soiled garments.
Sanitize - For heavily soiled, colorfast garments. This cycle heats the water to
150°F(65.6°C) to eliminate bacteria.
If Pause is selected during the heating portion of the sanitize cycle, your
washer door will remain locked for your safety.
Bedding - For bulky items such as blankets and sheets. When you are
washing comforters, use liquid detergent.
Deep steam - For heavily soiled, colorfast garments, this cycle provides high
washing temperature and steam and is efficient in cleaning stains.
Delicates - For sheer fabrics, bras, lingerie silk, and other handwash-only
fabrics. For best results, use liquid detergent.
Hand Wash - For handwashable, special care garments.
Wool - For machine-washable wool. Loads should be under 8 pounds.
• The Wool course washes laundry by moving the wash tub horizontally to
maintain the characteristics of the wool fibers and to prevent damaging
the cloth. It then stops for a while to allow the laundry to soak in the
water.This stop operation is not a problem. (You can only set the spin
speed to 800 rpm and the water temperature to 40°C.)
• It is recommended using a neutral detergent to prevent damage to the
cloth and to improve the washing results.
The wool wash cycle of this machine has been approved by
Woolmark for the washing of machine washable Woolmark
products provided that the products are washed according
to the instructions on the garment label and those issued by
the manufacturer of this washing machine, M0904.
Quick Wash - For lightly soiled garments needed quickly.
Rinse + Spin - Use for loads that need rinsing only or to add rinse-added
fabric softener to a load.
Spin Only - Provides a spin to remove more water.
3
6
5
4
7
9
1
2
10
8
Load Sensing Rinse SpinWash
1
BEST-WF419AAW-02657A_EN.indd 14 2009-02-18 ¿ÀÈÄ 3:26:47
Washing a load of laundry _15
Digital graphic
display
Displays the remaining cycle time, all cycle information, and error messages.
Select Cycle
Option
Press these buttons to select different cycle options.
Pre Wash - To use this feature add detergent to the pre wash section of the
detergent compartment. When turned on, the washer fills with cold water and
detergent, tumbles, then drains and advances to the selected wash cycle.
Some cycles cannot be selected with with this option (page 28).
* You cannot select the prewash option in the delicate, wool, quick wash
hand wash, rinse+spin, and spin only cycles.
Extra Rinse - Add an additional rinse at the end of the cycle to more
thoroughly remove laundry additives and perfumes.
Extended Spin - Add additional time to remove more water from loads.
My Cycle - Choose your favorite cycle including temperature, spin, soil level, option, etc.
Delay Start - Any cycle can be delayed for up to 24 hours in one-hour
i
ncrements. Displayed hour indicates the time at which the wash will be started.
Signal On/Off - Press the button to increase or decrease the end of cycle
signal volume or turn off the signal.
ActivFresh™
button
Press this button to sanitize your laundry in cold water.
Active silver ions are produced from pure silver plates by the process of
electrolysis and released into the wash water effectively sanitizing your wash,
even in cold water, without bleach. The ActivFresh™ system sanitizes while
using 92% less energy use than traditional heat sanitization.
Temperature
selection button
Press the button repeatedly to cycle through the different water temperature options.
Extra Hot/Cold - Heavily soiled, colorfast items. Only available with the Sanitize cycle.
Hot/Cold - Whites and heavily soiled, colorfast items.
Warm/Warm - Colorfast items. When warm rinse is selected, only the final rinse will
be warm.
The other rinses will be cold to conserve energy.
Warm/Cold - Moderately soiled, colorfast items; most wrinkle-free items.
Cold/Cold - Brightly colored, very lightly soiled items.
Spin selection
button
Press the button repeatedly to cycle through the different spin speed options.
Extra High - Removes more water from loads during spin.
To minimize wrinkling of wrinkle-free and no-iron fabrics, DO NOT use
the Extra High spin option for these loads, nor overload your washer.
High - Use for underwear, t-shirts, jeans and sturdy cottons.
Medium - Use for jeans, wrinkle-free or wash-and-wear items and synthetics.
Low - Use for delicate items needing a slow spin speed.
No Spin - Drains your washer without spinning. Use for extremely delicate
items that cannot tolerate any spin.
Soil Level
selection button
Press the button to select the Soil Level/washing time.
(Heave Normal Light)
Heavy - For heavily soiled loads.
-
Normal - For moderately soiled loads. This setting is best for most loads.
-
Light - For lightly soiled loads.
Steam selection
button
Press this button to use steam. steam care is available with Heavy Duty,
Normal, Perm Press, Sanitize, Bedding cycles. For heavily soiled, colorfast
garments. Steam care improves stain treatment and use less water of each
cycle (page 28).
Start/Pause
selection button
Press to pause and restart programs.
Power button
Press once to turn your washer on, press again to turn your washer off. If
the washer is left on for more than 10 minutes without any buttons being
touched, the power automatically turns off.
03 Washing a load of laundry
5
6
4
7
3
8
9
10
2
BEST-WF419AAW-02657A_EN.indd 15 2009-02-18 ¿ÀÈÄ 3:26:47
16_ Washing a load of laundry
Child lock
A function that prevents children from playing with your washer.
Once the Child Lock function is activated, the control panel cannot be activated, preventing
children from playing with the washer.
ACTIVATING/DEACTIVATING
If you want to activate/deactivate the Child Lock function, press the Spin and Soil Level buttons
at the same time for 3 seconds.
How It works:
1. “Child Lock” can be activated and deactivated while your washer is running.
2. Once you activate “Child Lock”, all controls (except for the Power button) will be locked
until you deactivate “Child Lock”.
3. The Child Lock button will be lit while it is in effect.
When buttons, other than the Power button, do not respond, please check if the “Child
Lock” function is on.
Garment+
You can add or take out laundry items even after the wash has started, as long as the “
(Garment+)” light is on. Pushing the Start/Pause button unlocks the door, unless the water is
too hot or if there is too much water in your washer. If you are able to unlock the door and wish
to continue the wash cycle, close the door and press the
Start/Pause button.
My cycle
Allows you to activate your custom wash (temperature, spin, soil level, etc.) with one–button
convenience.
By pushing the My Cycle button, you activate the settings used during the My Cycle mode.
The “My Cycle” light will indicate activation.
You can select all options as follows in the
“My Cycle” mode.
1. Select cycle using the Cycle Selector dial.
2. After cycle selection, set each option.
See page 28 for available option settings with each cycle.
3. Then, you can start “My Cycle” by pushing the Start/Pause button in “My Cycle” mode.
The cycle and options you select will be displayed the next time you choose “My Cycle”
.
You can change the
“My Cycle” settings by repeating the same process above.
The last used setting will be displayed the next time you choose “My Cycle”.
washing a load of laundry
BEST-WF419AAW-02657A_EN.indd 16 2009-02-18 ¿ÀÈÄ 3:26:47
Washing a load of laundry _17
Washing clothes using the cycle selector
Your new washer makes washing clothes easy, using Samsung’s “Fuzzy Control” automatic
control system. When you select a wash program, the machine will set the correct temperature,
washing time, and washing speed.
1. Almost no customers will have the washer hooked up via the sink’s tap.
2. Press the Power button.
3. Open the door.
4. Load the articles of clothing one at a time loosely into the drum, without overfilling it.
5. Close the door.
6. Add detergent, softener, and pre-wash detergent (if necessary) into the appropriate
compartments.
Pre-wash is only available when selecting the Normal, PermPress, Sanitize, Bedding and
Deep Steam cycles. It is only necessary if your clothing is heavily soiled(page 28).
7. Use the Cycle Selector to select the appropriate cycle according to the type of material:
Normal, PermPress, Sanitize, Bedding, Delicates, Hand Wash, Wool, Quick Wash, Rinse +
Spin, Spin Only, Deep Steam. The relevant indicators will illuminate on the control panel.
8. At this time, you can control the wash temperature, the number of rinse cycles, the spinning
speed, and the delay time by pressing the appropriate
Option button.
9. Press the Start/Pause button on the Cycle Selector and the wash will begin. The process
indicator will light up and the remaining time for the cycle will appear in the display.
Pause Option
To unlock the door when the “Garment+” LED is turned on, press the Start/Pause button.
1. Within 5 minutes of starting a wash, you can still add/remove laundry items to the wash.
2. Press the Start/Pause button to unlock the door.
3. The door cannot be opened when the water is too HOT or the water level is too HIGH.
4. After closing the door, press the Start/Pause button to restart the wash.
When the cycle is finished:
When the cycle is complete, “End” is displayed and the power remains on.
The power is turned off in the following two cases.
1. When the Power button is pressed.
2. If the door is opened when “End” is displayed.
03 Washing a load of laundry
BEST-WF419AAW-02657A_EN.indd 17 2009-02-18 ¿ÀÈÄ 3:26:48
18_ Washing a load of laundry
FOR ACTIVFRESH™ WASHING
An increased consumer demand for energy-saving products prompted Samsung to develop a system to
use silver, widely known for its antimicrobial properties, as a sanitizing agent in your washer.
Pure silver atoms have an electron stripped away by electrolysis during the wash and rinse cycles, which
releases up to 16 million trillion silver ions that then penetrate deep into the fabric to sanitize clothing
(according to U.S. EPA Test Guideline DIS/TSS-13). It does not need hot water or bleach.
Here’s how it works: A grapefruit-sized device alongside the tub uses two pure silver plates the size of large
chewing gum sticks as electrodes in the water inlet system. The resulting positively charged silver atoms
- Silver ions (Ag+) -- are sprayed into the tub during the wash and final rinse cycle.
During tests, this process removed more than 99.9% of bacteria.
Extra delicate blouses, shirts, or even lingerie that can’t be washed in hot water can now be sanitized
effectively without the adverse effects of hot water. The silver plates can easily be replaced by a Service
Technician if needed.
To use :
1. Load the washer.
2. Press the Power button.
3. Select a Cycle by turning the Cycle Selection dial.
4. Press the ActivFresh™ button.
5. Add detergent in the dispenser tray for main washing, and add fabric softener up to the marked line.
6. Press the Start/Pause button.
: The washer automatically selects optimal washing conditions by sensing the laundry’s weight.
FOR HOME USE ONLY– COMMERCIAL USERS SHOULD NOTIFY THEIR LOCAL WASTE
TREATMENT AUTHORITIES BEFORE USE
The total number of silver cycles run by the washer is displayed when pushing the Signal button and the
ActivFresh™
button simultaneously while the power is on.
LU1 : less than 1000 cycles
LU0 : 1000 cycles
The total number of silver cycles run by the washer is displayed when pushing the Signal and
ActivFresh™
buttons simultaneously while the power is on.
You cannot choose the ActivFresh™ , spin only option with the Wool cycle.
USING STEAM WASH
The Steam Wash function injects steam directly into the laundry in the wash tub to increase the wash
temperature and enhance the Soak effect, thus improving the wash performance.
1. Load the washer.
2. Press the Power button.
3. Turn the Cycle Selector and select a Steam Cycle. (The Deep Steam course automatically selects
Steam.)
4. Press the Steam button.
5. Add detergent into the dispenser tray for a wash, and add fabric softener up to the marked line.
6. Press the Start/Pause button.
: The washer automatically selects the optimal wash conditions by sensing the weight of the laundry.
If steam wash is selected, steam is injected at the most effective time for the detected amount of
laundry in order to maximize the effect of the steam.
washing a load of laundry
BEST-WF419AAW-02657A_EN.indd 18 2009-02-18 ¿ÀÈÄ 3:26:48
Washing a load of laundry _19
DETERGENT USE
Your washer is designed to use high efficiency (HE) detergents.
• For best cleaning results, use a high efficiency detergents such as Tide
HE, Wisk HE, Cheer HE or Gain HE*. High efficiency detergents contain
suds suppressors that reduce or eliminate suds. When fewer suds are
produced, the load tumbles more efficiently and cleaning is maximized.
Regular detergent is not recommended. Please use HE detergents
only.
Reducing the amount of detergent may reduce the cleaning quality. It is important to pre–treat stains,
sort carefully by color and soil level, and avoid overloading.
* Brand names are trademarks of their respective manufacturers.
FEATURES
Automatic dispenser
Your washer has separate compartments for dispensing
detergent and color-safe bleach, chlorine bleach, and fabric
softener. All laundry additives are added to their respective
compartments before starting your washer.
The automatic dispenser MUST ALWAYS be in place before
starting your washer.
DO NOT open the automatic dispenser when your washer is
running.
To use:
1. Pull out the dispenser drawer on the left side of the control
panel.
2. Add the recommended quantity of additive to the
appropriate compartments with laundry additives, and be
careful not to overfill or spill.
3. Slide the dispenser drawer carefully and completely back
into the compartment.
Detergent compartment
1. Pour the recommended amount of laundry detergent directly into the detergent compartment
before starting your washer.
2. If color-safe bleach is to be used, it should be added with detergent to the detergent
compartment.
• When adding color-safe bleach with detergent, it is best if both laundry products are in
the same form – granular or liquid.
If using liquid detergent, lower the detergent selector and add the detergent to the
detergent compartment.
03 Washing a load of laundry
CAUTION
Detergent
selector
Pre wash
compartment
Detergent
compartment
BEST-WF419AAW-02657A_EN.indd 19 2009-02-18 ¿ÀÈÄ 3:26:48
20_ Washing a load of laundry
Pre wash compartment
When using the Pre Wash option, detergent should be added to both the Pre Wash
compartment and the detergent compartment. The detergent will automatically be dispensed
during Pre Wash.
• If high efficiency (HE) detergent is used, add 1/3 of the recommended amount to the Pre
Wash compartment and 2/3 of the recommended amount to the detergent compartment.
Bleach compartment
(Liquid chlorine bleach only)
1. Add chlorine bleach to the bleach compartment.
DO NOT exceed the MAX FILL line.
2. Avoid splashing or over–filling the compartment.
3. Your washer automatically dispenses bleach into the tub at
the appropriate time.
4. The dispenser automatically dilutes liquid chlorine bleach
before it reaches the wash load.
• Never pour undiluted liquid chlorine bleach directly onto
the load or into the tub. It is a powerful chemical and
can cause fabric damage, such as weakening of the
fibers or color loss, if not used properly.
• If you prefer to use color–safe, non–chlorine bleach,
add it to the appropriate detergent compartment.
DO NOT pour color–safe bleach into the Bleach
compartment.
Fabric softener compartment
1. Pour the recommended amount of liquid fabric softener into the softener compartment.
For smaller loads, use less than one capful.
2. Fabric softener should be diluted with water until it reaches MAX FILL in the compartment.
3. The dispenser automatically releases liquid fabric softener at the proper time during the rinse
cycle.
• Use the softener compartment ONLY for liquid fabric softeners.
• DO NOT use a Downy Ball* in the Fabric softener compartment of this washer. It will not
add fabric softener at the appropriate time.
Use the detergent compartment.
* Brand names are trademarks of their respective manufacturers.
washing a load of laundry
Fabric Softener
compartment
Bleach
compartment
BEST-WF419AAW-02657A_EN.indd 20 2009-02-18 ¿ÀÈÄ 3:26:49
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
Samsung VRT STEAM WF419AAW Manuel utilisateur
- Catégorie
- Machines à laver
- Taper
- Manuel utilisateur
dans d''autres langues
Documents connexes
-
Samsung WF419AAU/XAA Manuel utilisateur
-
-
-
-
-
-
-
-
Samsung WF229ANG Manuel utilisateur
-
Autres documents
-
Haier GWT750AW Manuel utilisateur
-
Midea MLH52S7AGS Manuel utilisateur
-
-
Amana NFW7200TW Manuel utilisateur
-
Midea MLH27N4AWWC Manuel utilisateur
-
GE SH208 Manuel utilisateur
-
-
Alliance Laundry Systems 802756R3 Manuel utilisateur
-
-
Miele 51613745USA Mode d'emploi