Hitachi RAK-18QXB Le manuel du propriétaire

– 1 –

SPLIT TYPE AIR CONDITIONER

INDOOR UNIT

MODEL

This room air conditioner is only for consumer usage.

Do not use for preservation of foods, animals, plants, precision machines, art, medicine or such.

Instruction manual

Page 1~10

To obtain the best performance and ensure years of

trouble free use, please read this instruction manual

completely.

RAR-6N1

RAK-35RXB

RAK-50RXB

RAK-25RXB

RAK-18QXB

RAK-25RXB

RAK-18QXB

RAK-35RXB

RAK-50RXB

– 2 –

• Please read the “Safety Precaution” carefully before operating the unit to ensure correct usage of the unit.

• Pay special attention to signs of “

Warning” and “ Caution”. The “Warning” section contains matters which, if

not observed strictly, may cause death or serious injury. The “Caution” section contains matters which may result

in serious consequences if not observed properly. Please observe all instructions strictly to ensure safety.

• The signs indicate the following meanings. (The following are examples of signs.)

PRECAUTIONS DURING OPERATION

WARNING

SAFETY PRECAUTION

• Do not reconstruct the unit.

Water leakage, fault, short circuit or fi re may occur if you reconstruct the unit by

yourself.

• Please ask your sales agent or qualified technician for the installation of your unit.

Water leakage, short circuit or fire may occur if you install the unit by yourself.

• Please use earth line.

Do not place the earth line near water or gas pipes, lightning-conductor, or the

earth line of telephone. Improper installation of earth line may cause electric

shock or fire.

• Be sure to use the specifi ed piping set for R410A. Otherwise, this may result in

broken copper pipes or faults.

• A circuit breaker should be installed depending on the mounting site of the unit.

Without a circuit breaker, the danger of electric shock exists.

•

• Please ensure smooth fl ow of water when installing the drain hose.

• Make sure that a single phase power source is used.

The use of other power sources may cause electrical components to overheat

and lead to fi re.

PRECAUTIONS DURING INSTALLATION

PROHIBITION

CONNECT EARTH LINE

PROHIBITION

WARNING

CAUTION

•

• Please contact your agent for maintenance. Improper self maintenance may cause electric

shock and fi re.

• Please contact your agent if you need to remove and reinstall the unit. Electric shock or fi re

may occur if you remove and reinstall the unit yourself improperly.

PRECAUTIONS DURING SHIFTING OR MAINTENANCE

• Do not use any conductor as fuse wire, this could cause fatal accident.

• During thunder storm, disconnect the plug top and turn off the circuit

breaker.

• Do not put objects like thin rods into the panel of blower and suction side

because the high-speed fan inside may cause danger.

• Spray cans and other combustibles should not be located within a meter of the

air outlets of both indoor and outdoor units.

As a spray can’s internal pressure can be increased by hot air, a rupture may result.

PROHIBITION

“OFF”

PROHIBITION

Avoid an extended period of direct airflow for your health.

220V-230V

 Please keep this manual after reading.

Make sure to connect earth line.

Indicates the instructions that must be followed.

This sign in the figure indicates prohibition.

Do not install the unit near a location where there is flammable gas.

The outdoor unit may catch fire if flammable gas leaks around it.

Should abnormal situation arise (like burning smell), please stop operating the

unit and turn off the circuit breaker. Contact your

fire may occur if you continue to operate the unit

under abnormal situation.

agent. Fault, short circuit or

– 3 –

• .stnalp eht rof dab si ti sa wo lfria eht rednu yltcerid stnalp ecalp ton oD

• Do not direct the cool air coming out from the air-conditioner panel to face

household heating apparatus as this may affect the working of apparatus such

as the electric kettle, oven etc.

• ton dna noitac ificeps rerutcafunam eht rednu detarepo eb llahs tcudorp ehT

for any other intended use.

PRECAUTIONS DURING OPERATION

CAUTION

• Do not attempt to operate the unit with wet hands, this could cause fatal

accident.

• When operating the unit with burning equipments, regularly ventilate

.ycneic iffusni negyxo diova ot moor eht

• tuohtiw dna mr if ,elbats syawla si emarf gnitnuom roodtuo taht erusne esaelP

defect. If not, the outdoor unit may collapse and cause danger.

• Do not wash the unit with water or place a water container such as a vase on

the indoor unit.

Electrical leakage could be present and cause electric shock.

• Be sure to stop the operation by using the remote controller and turn off the

circuit breaker during cleaning, the high-speed fan inside the unit may cause

danger.

• Turn off the circuit breaker if the unit is not be operated for a long period.

• Do not climb on the outdoor unit or put objects on it.

• When operating the unit with the door and windows opened, (the room

gnivom ro nwod gnicaf rotce lfed ria eht htiw dna )%08 evoba syawla si ytidimuh

automatically for a long period of time, water will condense on the air deflector

and drips down

occasionally. This will wet your furniture. Therefore, do not

operate under such condition for a long time.

• If the amount of heat in the room is above the cooling or heating capability of

the unit (for example: more people entering the room, using heating equipments

and etc.), the preset room temperature cannot be achieved.

• Indoor unit cleaning must be performed by authorized personnel only. Consult

your sales agent.

Using a commercially available detergent or similar can damage the plastic parts

or clog the drain pipe, causing water to drip with potential electric shock hazard.

• roodtuo eht fo n if muinimula dna ecafrus mottob ,teltuo ria eht hcuot ton oD

unit.

You may get hurt.

Do not touch the refrigerant pipe and connecting valve.

Burns may result.

PROHIBITION

DON’T WET

PROHIBITION

DON’T TOUCH

“OFF”

PROHIBITION

DON’T TOUCH

STRICTLY OBSERVE

PRECAUTIONS

“OFF”

•

This appliance is not to be used by children or persons with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge, unless they have been given

supervision or instruction. Children must be supervised not to play with the appliance.

– 4 –

NAMES AND FUNCTIONS OF EACH PART

OPERATING RANGE

Operation mode Cooling / Dehumidifying Heating

C°12 ot 51-C°34 ot 01-erutarepmet roodtuO

NOTE FOR MULTI SYSTEM

Several indoor units can be connected to one outdoor unit.

You can operate only one unit or several units according to your needs.

Combination of operations:

When operation mode is selected:

You cannot operate the indoor units in the

following combinations.

One unit Other unit

Heating

Cooling

Dehumidifying

Fan

During automatic operation

The indoor unit which is turned on first continues to

operate. Other indoor units which are turned on later

go into standby mode and the operation lamp lights.

To operate the indoor units turned on later, set the

operation mode as same as the indoor unit turned

on first.

When heating operation is automatically selected for the first indoor unit, the next indoor unit will then start to

heat. Also, if cooling or dehumidifying is automatically selected for the first indoor unit, the next indoor unit will

also start to cool or dehumidify.

Adjusting the number of indoor units:

Decrease the number of indoor

units to be operated especially

when it is very hot or very cold

or when you want to reach the

preset temperature quickly.

Stopped indoor units:

When an indoor unit is operated in the cooling,

heating or dehumidifying mode in one room,

the sound of refrigerant flow may be heard

from a stopped indoor unit or a stopped indoor

unit may become warm. This is because the

indoor unit returns refrigerant to the outdoor

unit to be ready for operation.

INDOOR UNIT

Air filter

To prevent dust from coming into the indoor unit.

(Refer page 6)

Front panel

(Refer page 7)

Indoor unit indicators

Light indicator showing the operating condition.

(Refer page 5)

Horizontal deflector Vertical deflector

(Air Outlet)

Remote controller

Send out operation signal to the indoor unit. So as to

operate the whole unit.

MODEL NAME AND DIMENSIONS

MODEL WIDTH (mm) HEIGHT (mm) DEPTH (mm)

900 295 210

RAK-18QXB,RAK-25RXB,RAK-35RXB,RAK-50RXB

ECO Sensor

– 5 –

NAMES AND FUNCTIONS OF EACH PART

If the power stays on and the unit is not operated, power is slightly consumed in the control circuit.

The power is saved by turning off the power switch (or the circuit breaker when the power is supplied

from the outdoor unit).

Attaching the Wasabi-Nano Titanium Air Cleaning

Attach the

to the C-case by gently compress its both sides

and release after insertion into filter frame.

The cooling capacity is slightly weakened and

the cooling speed becomes slower when the

are used.

.

and reusable up to 20 times by using vacuum

cleaner or water rinse under running tap water.

When you want to renew it, please ask your sales

agent. Optional air cleansing and deodorizing

filters.

Air Filter

Claw

Filter Frame

Mesh (Accessories) to the filter frame.

Wasabi-Nano Titanium Air Cleaning Mesh

are washable

Wasabi-Nano Titanium Air Cleaning Mesh

C-case

INDOOR UNIT INDICATIONS

TIMER LAMP (Orange)

This lamp lights when the

timer is working.

OPERATION LAMP (Yellow)

This lamp lights during operation.

The OPERATION LAMP flashes

in the following cases during

heating.

(1) During preheating

For about 2-3 minutes after

starting up.

(2) During defrosting

Defrosting will be performed

about once an hour when frost

forms on the heat exchanger

of the outdoor unit, for 5-10

minutes each time.

TEMPORARY SWITCH

CAUTION

Turn off the circuit breaker

if the unit is not be operated

for a long period.

Use this switch to start and stop when the remote

controller does not work.

By pressing the temporary switch, the operation is

done in automatic mode.

When the operation is done using the temporary

switch after the power source is turned off and turn

on again, the operation is done in automatic mode.

ECO Sensor Lamp(Green)

– 2 –

PREPARATION BEFORE OPERATION

■ To install the batteries

■ To ﬁ x the remote controller holder to the wall

1. Slide the cover to take it off.

2. Install two dry batteries AAA.LR03 (alkaline).

The direction of the batteries should match the

marks in the case.

3. Replace the cover at its original position.

1. Choose a place from where the signals can reach the unit.

2. Fix the remote controller holder to a wall, a pillar or similar

location with the provided screws.

3. Place the remote controller in the remote controller holder.

NOTE

Notes on batteries

● When replacing the batteries, use batteries of the same

type, and replace both old batteries together.

● When the system is not used for a long time, take the

batteries out.

● The batteries will last for approximately 1 year. However, if

the remote controller display begins to fade and degradation

of reception performance occurs within a year, replace both

batteries with new size AAA.LR03 (alkaline).

● The attached batteries are provided for the initial use of

the system.

The usable period of the batteries may be short depending

on the manufactured date of the air conditioner.

Notes on the remote controller

● Never expose the remote controller to direct sunlight.

● Dust on the signal transmitter or receiver will reduce the

sensitivity. Wipe off dust with soft cloth.

● Signal communication may be disabled if an electronic-

starter-type ﬂ uorescent lamp (such as inverter-type lamps)

is in the room. Consult the shop if that is the case.

● If the remote controller signals happen to operate another

appliance, move that appliance to somewhere else, or

consult the service shop.

● When the remote controller is not in use, please close the

slide cover to prevent failure.

Remote controller

Screws

Remote

controller holder

– 3 –

ENGLISH

PREPARATION BEFORE OPERATION

■ To set calendar and clock

1. Press (RESET) button when ﬁ rst time setting.

"Year" blinks.

2. Press (TIME) button to set the current year.

3. Press (CLOCK) button. "Day" and "Month"

blink.

4. Press (TIME) button to set the current day and

month.

5. Press (CLOCK) button. "CLOCK" blinks.

6. Press (TIME) button to set the clock to the current

time.

7. Press (CLOCK) button.

Calendar and clock are set.

To modify the calendar and clock, press (CLOCK)

button.

Then follow steps 1 to 7.

Calendar and clock need to be set again after changing

batteries.

After changing the batteries,

1. Press (RESET) button.

2. Direct remote controller towards indoor unit and press

(INFO) button.

3. The calendar and clock from indoor unit will be transmitted.

■ Calendar and clock will not be transmitted from indoor

unit when the following occurs:

● When there is a power failure.

● When breaker is OFF by user (unit is not in STANDBY

MODE).

NOTE

Note on setting the calendar and clock.

● If the calendar and clock are not set, the ON-timer, OFF-timer and Weekly Timer cannot be set.

● If the calendar and clock are not set correctly, the ON-timer, OFF-timer and Weekly Timer will not

operate correctly.

● When the ON-timer, OFF-timer and Weekly Timer are set, the calendar and clock cannot be changed.

If there is a need to change the calendar and clock, ON-timer, OFF-timer and Weekly Timer need to

be cancelled.

– 4 –

NAMES AND FUNCTIONS OF REMOTE CONTROLLER

REMOTE CONTROLLER

● This controls the operation of the indoor unit. The range of control is about 7 meters. If indoor lighting is

controlled electronically, the range of control may be shorter.

This unit can be ﬁ xed on a wall using the ﬁ xture provided. Before ﬁ xing it, make sure the indoor unit can

be controlled from the remote controller.

● Handle the remote controller with care. Dropping it or getting it wet may compromise its signal transmission

capability.

● After new batteries are inserted into the remote controller, the unit will initially require approximately 10

seconds to respond to commands and operate.

● When remote controller is not in use for about 3 minutes during OFF condition, indicated by on the

display, the LCD will turn off.

● During clock setting, the LCD will turn off about 10 minutes later if the remote controller is not in use.

● When pressing any button, the LCD will turn on.

● The LCD will not turn off during TIMER setting.

Signal Transmitting/Receiving

Window

Point this window towards the

indoor unit when controlling it.

Sensor

A temperature sensor inside the

remote controller senses ambient

temperature around the remote-

controller.

Display

This indicates the room temperature

selected, current time, timer status,

function and airﬂ ow rate selected.

ROOM TEMPERATURE setting Buttons

Press these buttons to set the room

temperature.

Press the [ ] button to raise the room

temperature.

Press the [ ] button to lower the room

temperature.

Keep pressing and the value will change

more quickly.

ECO Button

Use this button to set the ECO

mode. ( p. 13)

START/STOP button

Press this button to start

operation. Press it again to stop

operation.

FAN SPEED selector Button

This determines the fan speed.

Every time you press this button,

the airﬂ ow rate will change from

(AUTO) ➞ (HIGH) ➞

(MED) ➞ (LOW) ➞

(SILENT) (This button allows

selection of optimal or preferred fan

speed for each operation mode).

Transmission sign

The transmission sign lights up

when a signal is sent.

– 5 –

ENGLISH

MODE SELECTOR

AUTO

HEAT

DEHUMIDIFY

COOL

FAN

FAN SPEED

AUTO

SILENT

LOW

MED

HIGH

START / STOP

ECO

Precautions for Use

●

Do not put the remote controller in the following places.

●

Under direct sunlight.

●

In the vicinity of a heater.

●

Handle the remote controller carefully. Do not drop it on the ﬂ oor, and protect it from water.

●

Once the outdoor unit stops, it will not restart for about 3 minutes (unless you turn the power switch

off and on or unplug the power cord and plug it in again).

This is to protect the device and does not indicate a failure.

●

If you press the MODE selector button during operation, the device may stop for about 3 minutes for

protection.

POWERFUL Button

Use this button to set the

POWERFUL mode. ( p. 11)

INFORMATION Button

(

p. 26)

ONE TOUCH CLEAN Button

( p. 16)

ON / OFF TIMER setting Buttons

( p. 17)

MODE selector Button

Use this button to select the

operating mode. Every time you

press this button, the mode will

change from (AUTO) ➞

(HEAT) ➞ (DEHUMIDIFY)

➞ (COOL) and ➞ (FAN)

cyclically.

SILENT Button

Use this button to set the SILENT

mode. ( p. 12)

AUTO SWING (Vertical) Button

Controls the angle of the

horizontal air deﬂ ector. ( p. 10)

AUTO SWING (Horizontal) Button

Controls the angle of the vertical

air deﬂ ector. ( p. 10)

WEEKLY TIMER setting Buttons

( p. 20)

LEAVE HOME Button

( p. 15)

NAMES AND FUNCTIONS OF REMOTE CONTROLLER

ECO SLEEP TIMER Button

Use this button to set the ECO

sleep timer. ( p. 18)

FAN

POWERFUL

SILENT

INFO

SLEEP TIMER

AUTO SWING (VERTICAL)

AUTO SWING (HORIZONTAL)

LEAVE HOME

CLEAN

DAY

PROGRAM NO.

ON / OFF TIMER

TIME

OK

DELETE

COPY / PASTE

CANCEL

SEND

CLOCK

– 6 –

AUTOMATIC OPERATION

The device will automatically determine the mode of operation, HEAT or COOL depending on the current

room temperature. The selected mode of operation will change when the room temperature varies.

However, the mode of operation will not change when indoor unit is connected to multi type outdoor unit.

VARIOUS FUNCTIONS

■ Auto Restart Control

● If there is a power failure, operation will be automatically restarted when the power is resumed with previous operation

mode and airﬂ ow direction.

(As the operation is not stopped by remote controller.)

● If you intend not to continue the operation when the power is resumed, switch off the power supply.

When you switch on the circuit breaker, the operation will be automatically restarted with previous operation mode

and airﬂ ow direction.

Note: 1. If you do not require Auto Restart Control, please consult your sales agent.

2. Auto Restart Control is not available when Timer or Sleep Timer mode is set.

■ As the settings are stored in the memory of the remote controller, you

only have to press the

(START/STOP) button next time.

Press the MODE selector button so that the display indicates the

(AUTO) mode of operation.

● When AUTO has been selected, the device will automatically

determine the mode of operation, HEAT or COOL depending on

the current room temperature. However the mode of operation will

not change when indoor unit is connected to multi type outdoor

unit.

● If the mode automatically selected by the unit is not satisfactory,

manually change the mode setting (HEAT, DEHUMIDIFY, COOL

or FAN).

Press the (FAN SPEED) button to select AUTO, HIGH, MED, LOW

or SILENT.

Press the (START/STOP) button.

Operation starts with a beep.

Press the button again to stop operation.

Set the desired room temperature with the TEMPERATURE buttons

(the display indicates the setting).

The temperature setting and the actual room temperature may vary

depending on conditions.

Temperature range can be set between 16°C and 32°C.

START

STOP

1

2

3

Set the desired FAN SPEED with the (FAN SPEED) button (the

display indicates the setting).

(AUTO) (HIGH) (MED)

(SILENT) (LOW)

– 7 –

ENGLISH

HEATING OPERATION

● Use the device for heating when the outdoor temperature is under 21°C.

When it is too warm (over 21°C), the heating function may not work in order to protect the device.

● In order to maintain reliability of the device, please use this device when outdoor temperature is above

–15°C.

Press the MODE selector button so that the display indicates

(HEAT).

Set the desired FAN SPEED with the (FAN SPEED) button

(the display indicates the setting).

(AUTO) (HIGH) (MED)

(SILENT) (LOW)

Set the desired room temperature with the TEMPERATURE buttons

(the display indicates the setting).

The temperature setting and the actual room temperature may

vary depending on conditions.

Temperature range can be set between 16°C and 32°C.

Press the (START/STOP) button. Heating operation starts with

a beep. Press the button again to stop operation.

■ As the settings are stored in the memory of the remote controller, you

only have to press the (START/STOP) button next time.

■ During AUTO fan, the fan speed automatically changes as below:

● When the difference between room temperature and setting temperature

is large, fan starts to run at HI speed.

● After room temperature reaches the preset temperature, fan speed

will be changed to lower speed to obtain optimum room temperature

condition for natural healthy heating.

START

STOP

Defrosting will be performed about once an hour when frost forms on the heat exchange of the outdoor unit,

for 5~10 minutes each time.

During defrosting operation, the operation lamp blinks in a cycle of 3 seconds on and 0.5 second off.

The maximum time for defrosting is 20 minutes.

However, if the indoor unit is connected to multi type outdoor unit, the maximum time for defrosting is 15

minutes.

(If the piping length used is longer than usual, frost is likely to form.)

1

2

3

Defrosting

– 8 –

DEHUMIDIFYING OPERATION

■ Dehumidifying Function

● When the room temperature is higher than the temperature setting: The device will dehumidify the room,

reducing the room temperature to the preset level.

When the room temperature is lower than the temperature setting: Dehumidifying will be performed at the

temperature setting slightly lower than the current room temperature, regardless of the temperature setting.

● The preset room temperature may not be reached depending on the number of people present in the room

or other room conditions.

Set the desired room temperature with the ROOM

TEMPERATURE setting buttons (the display indicates the

setting).

The range of 20-26˚C is recommended as the

room temperature for dehumidifying.

Temperature range can be set between 16°C

and 32°C.

Press the (START/STOP) button. Dehumidifying operation

starts with a beep. Press the button again to stop operation.

■ As the settings are stored in the memory of the remote controller, you

only have to press the (START/STOP) button next time.

START

STOP

Press the MODE selector button so that the display

indicates (DEHUMIDIFY).

The fan speed is set at LOW.

Press (FAN SPEED) button to select SILENT or LOW fan

speed.

Use the device for dehumidifying when the room temperature is over 16°C.

When it is under 15°C, the dehumidifying function will not work.

1

2

– 9 –

ENGLISH

COOLING OPERATION

Use the device for cooling when the outdoor temperature is -10~ 43°C.

If indoors humidity is very high (80%), some dew may form on the air outlet grille of the indoor unit.

Press the MODE selector button so that the display indicates

(COOL).

■ As the settings are stored in the memory of the remote controller, you

only have to press the (START/STOP) button next time.

■ During AUTO fan, the fan speed automatically changes as below:

● When the difference between room temperature and setting tem-

perature is large, fan starts to run at HI speed.

● After room temperature reaches the preset temperature, fan speed

will be changed to lower speed to obtain optimum room temperature

condition for natural healthy cooling.

START

STOP

1

2

3

Set the desired FAN SPEED with the (FAN SPEED) button (the

display indicates the setting).

(AUTO) (HIGH) (MED)

(SILENT) (LOW)

Set the desired room temperature with the TEMPERATURE buttons

(the display indicates the setting).

The temperature setting and the actual room temperature may vary

depending on conditions.

Temperature range can be set between 16°C and 32°C

Press the (START/STOP) button. Cooling operation starts with a

beep. Press the button again to stop operation. The cooling function

does not start if the temperature setting is higher than the current

room temperature (even though the (OPERATION) lamp lights).

The cooling function will start as soon as user set the temperature

below the current room temperature.

– 10 –

FAN OPERATION

AUTO SWING OPERATION

User can use the device simply as an air circulator.

VERTICAL SWING

HORIZONTAL SWING

START

STOP

1

2

Press the MODE selector so that the display indicates

(FAN).

Set the desired FAN SPEED with the (FAN SPEED) button (the

display indicates the setting).

(HIGH) (MED) (LOW) (SILENT)

Press the (START/STOP) button. Fan operation starts with

a beep. Press the button again to stop operation.

■ To start Vertical Auto Swing

■ To start Horizontal Auto Swing

■ To cancel Vertical Auto Swing

■ To cancel Horizontal Auto Swing

● Press (AUTO SWING (VERTICAL)) button. The deﬂ ector(s) will start

to swing up and down.

is displayed on the LCD.

● Press (AUTO SWING (HORIZONTAL)) button. The deﬂ ectors will

start to swing right and left.

is displayed on the LCD.

● Press (AUTO SWING (VERTICAL)) button again. The deﬂ ector(s)

will stop in the current position.

disappeared from the LCD.

● Press (AUTO SWING (HORIZONTAL)) button again. The deﬂ ectors

will stop in the current position.

disappeared from the LCD.

NOTE

● During cooling and dehumidifying operation, do not keep the deﬂ ectors swinging or in the lower position

(in the case of vertical auto swing) for a long time. It may cause dew condensation on the deﬂ ectors.

– 11 –

ENGLISH

POWERFUL OPERATION

● By pressing (POWERFUL) button during AUTO, HEATING, DEHUMIDIFYING, COOLING or FAN

operation, the air conditioner performs at the maximum power.

● During POWERFUL operation, cooler or warmer air will be blown out from indoor unit for COOLING or

HEATING operation respectively.

■ To start POWERFUL operation

■ To cancel POWERFUL operation

● Press (POWERFUL) button during operation.

“ ” is displayed on the LCD.

POWERFUL operation ends in 20 minutes. Then the system

automatically operates with the previous settings used before

POWERFUL operation.

● Press the (START/STOP) button. Or

● Press (POWERFUL) button again.

POWERFUL operation stops.

“ ” disappears from the LCD.

1

NOTE

● When SLEEP mode, ECO mode, SILENT mode or LEAVE HOME mode is selected, POWERFUL

operation is cancelled.

● During POWERFUL operation, capacity of the air conditioner will not increase

– if the air conditioner is already running at maximum capacity.

– just before defrost operation (when the air conditioner is running in HEATING operation).

● After auto restart, POWERFUL operation is cancelled and previous operation shall start.

● For multi model connections, POWERFUL operation may not function depending on operation conditions.

– 12 –

SILENT OPERATION

● By pressing (SILENT) button during AUTO, HEATING, DEHUMIDIFYING, COOLING or FAN

operation, the fan speed will change to ultra slow.

■ To start SILENT operation

■ To cancel SILENT operation

● Press (SILENT) button during operation.

“

” is displayed on the LCD. Fan speed will be ultra slow.

● Press (START/STOP) button. Or

● Press (SILENT) button again or (FAN SPEED)

button.

Fan speed will return to previous fan speed before SILENT

operation starts.

SILENT operation stops.

“ ” disappears from the LCD.

1

NOTE

● When POWERFUL operation is selected, SILENT operation is cancelled. Fan speed will return to

previous fan speed before SILENT operation.

● After auto restart, SILENT operation is cancelled. Fan speed will return to previous fan speed before

SILENT operation.

● During any operation with fan speed (SILENT), if press (SILENT) button, fan speed will

not change.

– 13 –

ENGLISH

ECO OPERATION

There are two kinds of ECO OPERATION with sensor or without sensor, depending on models.

Please refer to [Names and Functions of each part] in the unit instruction manual to verify if your unit is

equipped with a sensor and read the following instruction on ECO Operation accordingly.

● By pressing the (ECO) button during AUTO, HEATING,

DEHUMIDIFYING or COOLING operation, the air conditioner

performs the "ECO" operation.

1

■ To start ECO operation

■ To cancel ECO operation

● Press (ECO) button during operation.

“ ” is displayed on the LCD.

A beep sound is emitted from indoor unit.

Energy saving operation will start by changing the set temperature

higher or lower automatically and reducing operation power

consumption. This function may vary based on the connected

outdoor unit.

● Press (START/STOP) button. Or

● Press (ECO) button again.

“ ” disappears from the LCD.

A beep sound is emitted from indoor unit.

NOTE

● ECO function will not be effective when power consumption is low.

● By pressing (POWERFUL) button, ECO operation is cancelled.

● After auto restart, ECO operation is cancelled and previous operation mode shall start.

● For multi model connections, energy saving operation shall start only by changing set temperature higher

or lower automatically. However, effectiveness of ECO depends on operation conditions.

■ ECO OPERATION

ECO operation is an energy saving function by changing set temperature automatically and by limiting the

maximum power consumption value.

– 14 –

ECO OPERATION

● By pressing the (ECO) button during AUTO, HEATING,

DEHUMIDIFYING or COOLING operation, the air conditioner

performs the "ECO" operation.

1

■ To start ECO operation

■ To cancel ECO operation

● Press (ECO) button during operation.

“ ” is displayed on the LCD.

A beep sound is emitted from indoor unit and the (ECO) lamp

on the indoor unit lights up.

The sensor starts to detect the presence of people in the room.

● Press (START/STOP) button. Or

● Press (ECO) button again.

“ ” disappears from the LCD.

A beep sound is emitted from indoor unit and the (ECO) lamp on

the indoor unit turns off.

NOTE

● By pressing (POWERFUL) button, ECO operation is cancelled.

● After auto restart, ECO operation is cancelled and previous operation mode shall start.

■ ECO OPERATION with sensor

The sensor detects the presence of people in the room. When nobody is detected, the unit automatically starts

enegy saving operation by shifting the set temperature in two steps.

When the presence of people is not detected for 20 minutes, the set temperature is automtatically shifted for

energy saving. If nobody is in the room for 60 minutes, the set temperature is shifted further.

Cooling operation [diagram representation

for illustrative purpose only]

Heating operation [diagram representation

for illustrative purpose only]

Setting

temperature

Shift

temperature

Shift

temperature

20 minutes 60 minutes

Setting

temperature

Shift

temperature

Shift

temperature

20 minutes 60 minutes

The unit returns to normal operation when the sensor detects human movement.

– 15 –

ENGLISH

LEAVE HOME (LH) OPERATION

Prevent the room temperature from falling too much when no one is at home. The initial setting temperature is 10°C and the

temperature range can be set between 10°C and 16°C.

This operation is able to operate by "Continuous operation" or "Day timer operation". Please use "Day timer operation" to

set the number of days up to 99 days.

■ To start LEAVE HOME operation

Option 1. Continuous operation.

Press (LEAVE HOME) button during stop or operation.

Room temperature is set at 10°C and heating operation starts.

Set the desired room temperature with the TEMPERATURE buttons.

Temperature range can be set between 10°C and 16°C.

“

”, “ ”, “ ”, “ ”, “SET TEMPERATURE” is displayed

on the LCD.

Option 2. Day timer operation.

Press (LEAVE HOME) button during stop or operation.

Room temperature is set at 10°C and heating operation starts.

Set the desired room temperature with the TEMPERATURE buttons.

Temperature range can be set between 10°C and 16°C.

“ ”, “ ”, “ ”, “ ”, “SET TEMPERATURE” is displayed

on the LCD.

Set number of operation days (1 to 99 days), if needed.

Press

(TIME) button to select number of days.

Number of days blink.

* Press “

(UP)” or “ (DOWN)” to set number of days from

1 day to 99 days.

* Number of day is counted when clock indicates 0:00.

Press (SEND) button to conﬁ rm number of operation days.

Display for number of operation days will stop blinking.

Press (CANCEL) button to reset number of operation days

or to have continuous operation.

To cancel LEAVE HOME operation

● Press (START/STOP) button. Or

● Press (LEAVE HOME) button again.

Return to previous operation mode. Or

● Change to other operation mode by pressing (MODE) button.

NOTE

● After reaching the set number of operation days for Leave Home or by pressing the (Leave Home) button again,

the unit will operate in previous mode.

● During Leave Home operation, fan speed and horizontal air deﬂ ector position cannot be changed.

● By pressing (Leave Home) button, implementation of Weekly Timer or Once Timer is cancelled.

● In case of power supply shut down, after autorestart, all setting for number of days operation will be reset and unit

shall be in continuous operation.

● POWERFUL, SILENT and ECO operations are not applicable during Leave Home operation.

● For multi connection

● FAN/COOLING/DEHUMIDIFYING and Leave Home cannot operate at the same time.

The ﬁ rst-run unit has a priority and other units in different mode will be in standby mode.

● Heating operation can be used with Leave Home.

● When two or more rooms are set to operate Leave Home, the temperature set by Leave Home may not be

reached. It also depends on outdoor temperature.

Continuous operation

Day timer operation

1

2

1

2

1

2

3

4

3

4

– 16 –

CLEAN (ONE TOUCH CLEAN) OPERATION

Drying indoor heat exchanger after cooling operation to prevent mildew.

■ To start CLEAN operation

■ To cancel CLEAN operation

● Press (CLEAN) button when unit is OFF.

Total time taken for One Touch Clean operation is 60 minutes.

During this operation, HEATING or FAN operation shall

operate.

During one touch clean, operation lamp is blinking.

“

”, “ ” is displayed on the LCD.

● Press (START/STOP) button. Or

● Press (CLEAN) button again.

1

NOTE

● When CLEAN operation ﬁ nish, unit will switch OFF automatically.

● If Weekly Timer or Once Timer is set, there is a need to cancel those timer before operating CLEAN

function.

● For multi connections, when pressing (CLEAN) button, operation is limited to FAN operation.

● For multi connections, when one room operates CLEAN operation ﬁ rst, other rooms can operate

COOLING, DEHUMIDIFYING or FAN operation. However, when other rooms need to operate HEATING

operation, air conditioner will be in STANDBY mode. After CLEAN operation ﬁ nish, HEATING operation

will start.

La page charge ...

Hitachi RAK-18QXB Le manuel du propriétaire

Ce manuel convient également à

Hitachi RAK-18QXB Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents