Hitachi RAC-18SX8 Manuel utilisateur

TC

SERVICE MANUAL

TECHNICAL INFORMATION

INFORMATIONS TECHNIQUES

REFER TO THE FOUNDATION MANUAL

REPORTEZ-VOUS AU MANUEL DE BASE

ROOM AIR CONDITIONER

SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT

LES SPECIFICATIONS ET PIECES DETACHEES PEUVENT CHANGER POUR ETRE AMELIOREES.

FOR SERVICE PERSONNEL ONLY

RESERVE AU PERSONNEL

NO. 0790EF

RAS-18SX8 /

RAC-18SX8

798

295

233

11.5

750 (+86)

570

288 (+56)

36

RAS-18SX8 RAC-18SX8

1ø, 220V - 230V, 50Hz

300 (70 - 880)

1.70 - 1.63

1.8 (0.5 - 3.0)

6,143 (1,707 - 10,239)

375 (65 -1,070)

2.13 - 2.04

2.3 (0.6 - 4.8)

7,850 (2,048 - 16,382)

RAS-18SX8

RAC-18SX8

SPECIFICATIONS

CARACTERISTIQUES GENERALES

SPECIFICATIONS

CARACTERISTIQUES GENERALES

HOW TO USE

UTILISATION

CONSTRUCTION AND DIMENSIONAL DIAGRAM

DIMENSIONS DES UNITÉS

MAIN PARTS COMPONENT

PRINCIPAUX COMPOSANTS

WIRING DIAGRAM

SCHÉMA ÉLECTRIQUE

WIRING DIAGRAM OF THE PRINTED WIRING BOARD

SCHÉMA ÉLECTRIQUE DU CIRCUIT IMPRIMÉ

BLOCK DIAGRAM

ORGANIGRAMME DE CONTRÔLE

BASIC MODE

MODE DE BASE

REFRIGERATING CYCLE DIAGRAM

SCHÉMA DU CYCLE DE RÉFRIGÉRATION

PROCÉDURE D'ASSEMBLAGE ET DESASSEMBLAGE

DESCRIPTION OF MAIN CIRCUIT OPERATION

DESCRIPTION DES PRINCIPAUX CIRCUITS

SERVICE CALL Q&A

MODE OPERATOIRE DE DEPANNAGE

TROUBLE SHOOTING

DETECTION DES PANNES

PARTS LIST AND DIAGRAM

LISTE DES PIÉCES DE RECHANGE

CONTENTS

TABLE DES MATIERES

INDOOR UNIT + OUTDOOR UNIT

DECEMBER 2008 Hitachi Appliances, Inc.

8

9

60

64

67

71

83

87

150

152

158

198

214

280

After installation Après installation

DC INVERTER INVERSEUR C.C.

COOLING

RÉFRIGÉRATION

HEATING

CHAUFFAGE

TYPE TYPE

MODEL

POWER SOURCE

TOTAL INPUT

TOTAL AMPERES

CAPACITY

TOTAL INPUT

TOTAL AMPERES

CAPACITY

DIMENSIONS

NET WEIGHT

MODÈLE

SOURCE D'ALIMENTATION

(PHASE/TENSION/FREQUENCE)

PUISSANCE ABSORBEE TOTALE

AMPERES TOTAUX

CAPACITE

PUISSANCE ABSORBEE TOTALE

AMPERES TOTAUX

CAPACITE

DIMENSIONS

(mm)

POIDS NET

(A)

(B.T.U./h)

W, L

H, H

D, P

(kg)

(kW)

(A)

(B.T.U./h)

(kW)

(W)

INDOOR UNIT

UNITÉ INTÉRIEURE

OUTDOOR UNIT

UNITÉ EXTÉRIEURE

OUTDOOR UNIT

UNITÉ EXTÉRIEURE

INDOOR UNIT

UNITÉ INTÉRIEURE

1. In order to disassemble and repair the

unit in question, be sure to disconnect the

power cord plug from the power outlet

before starting the work.

2. If it is necessary to replace any parts, they should be replaced with respective genuine parts for the unit,

and the replacement must be effected in correct manner according to the instructions in the Service

Manual of the unit.

3. After completion of repairs, the initial state should be

restored.

4. Lead wires should be connected and laid as in the

initial state.

5. Modification of the unit by the user himself should

absolutely be prohibited.

6. Tools and measuring instruments for use in repairs or inspection should be accurately calibrated in

advance.

7. In installing the unit having been repaired, be careful to prevent the occurrence of any accident such as

electrical shock, leak of current, or bodily injury due to the drop of any part.

8. To check the insulation of the unit, measure the insulation resistance between the power cord plug and

grounding terminal of the unit.

The insulation resistance should be 1MΩ or more as measured by a 500V DC megger.

9. The initial location of installation such as window, floor or the other should be checked for being safe

enough to support the repaired unit again.

If it is found not so strong and safe, the unit should be installed at the initial location after reinforced or

at a new location.

10. Any inflammable object must not be placed

about the location of installation.

11. Check the grounding to see whether it is

proper or not, and if it is found improper,

connect the grounding terminal to the earth.

Spray

gasoline

gasbombe

thinner

SAFETY DURING REPAIR WORK

If the contacts of electrical

parts are defective, replace

the electrical parts without

trying to repair them

1

2

3

4

5

– 1 –

1. Avant de procéder à une réparation, veillez

à couper l'alimentation électrique.

2. Les pièces de rechange doivent être des pièces d'origine et le remplacement des pièces doit être réalisé

conformément aux instructions figurant dans le manuel d'entretien.

3. Après achèvement des réparations, les conditions

initiales doivent être rétablies.

4. Après toute intervention, le raccordement et le

cheminement des câbles électriques doivent être

rétablis comme à l'origine.

5. Toute modification au niveau de l'installation ne peut être effectuée que par une personne compétente.

Toute intervention ou modification par l'utilisateur lui-même est par conséquent à proscrire.

6. Les outils et les appareils de mesure qui doivent être employés pour effectuer l'entretien auront été

préalablement réglés ou étalonnés comme il convient.

7. Lors de l'installation d'une unité ayant subi une réparation, veillez à éviter tout accident dû à une décharge

électrique ou la chute d'un objet.

8. Pour vérifier l'isolement de l'appareillage, mesurer la résistance entre le cordon d'alimentation et la borne

de masse. Cette résistance doit au moins être égale à 1MΩ lorsque la mesure est effectuée avec un

mégohmmètre de 500V CC.

9. Avant la fixation de l'unité réparée, vérifiez que les fixations d'origine peuvent supporter l'appareil. Si ces

fixations vous paraissent défectueuses, renforcez-les si possible et dans le cas contraire, l'unité doit être

fixée à un autre endroit.

10. L'emplacement de l'installation doit être

éloigné de toute matière inflammable.

11. La mise à la masse doit être soigneusement

contrôlée; en cas de défaut, la borne de

masse doit être mise à la terre.

Il faut d'abord que je coupe

I'alim

entation électrique.

Aérosol

Essence

Dilunt

Bonbonne de gaz

PRECAUTIONS RELATIVES A LA SECURITE PENDANT LES REPARATIONS

Si vous constatez que les contacts d'un

composant électrique sont défectueux,

remplacez le composant et ne tentez pas

de réparer les contacts.

1

2

3

4

5

– 2 –

WORKING STANDARDS FOR PREVENTING BREAKAGE OF SEMICONDUCTORS

1. Scope

The standards provide for items to be generally observed in carrying and handling semiconductors in

relative manufactures during maintenance and handling thereof. (They apply the same to handling of

abnormal goods such as rejected goods being returned.)

2. Object parts

(1) Microcomputer

(2) Integrated circuits (I.C.)

(3) Field effective transistor (F.E.T.)

(4) P.C. boards or the like to which the parts mentioned in (1) and (2) of this paragraph are equipped.

3. Items to be observed in handling

(1) Use a conductive container for carrying and storing of parts. (Even rejected goods should be handled in

the same way.)

(2) When any part is handled uncovered (in counting, packing and the like), the handling person must

always use himself as a body earth. (Make yourself a body earth by passing one M ohm earth

resistance through a ring or bracelet.)

(3) Be careful not to touch the parts with your clothing when you hold a part even if a body earth is

being taken.

(4) Be sure to place a part on a metal plate with grounding.

(5) Be careful not to fail to turn off power when you repair the printed circuit board. At the same time,

try to repair the printed circuit board on a grounded metal plate.

H

IT

A

C

H

I I

C

4

0

1

T

H

1

,

1

8

U

V

Fig. 1 Conductive container

A conductive polyvinyl bag

IC

Conductive sponge

Fig. 2 Body earth

Body earth (Elimik conductive band)

Clip for connection with

a grounding wire

1MΩ

– 3 –

PREVENTION DES DOMMAGES AUX SEMI-CONDUCTEURS

1. Champ d'application

Pour éviter d'endommager les semi-conducteurs utilisés dans les unités, lors de chaque intervention

d'entretien ou de réparation, vous devez observer des précautions spéciales. Les mêmes précautions

doivent être prises lors de la manipulation d'organes défectueux qui doivent être retournés en usine.

2. Pièces détachées de l'appareillage.

(1) Microprocesseur

(2) Circuits intégrés (C.I.)

(3) Transistor à effet de champ (T.E.C)

(4) Circuits imprimés sur lesquels se trouvent implantés les composants (1) et (2).

3. Précautions de manipulation

(1) Pour transporter ou stocker un semi-conducteur, placez-le dans un emballage conducteur. Procéder de

même avec un composant défectueux.

(2) Lorsque vous maniqulez des composants qui ne sont pas protégés (par exemple pour les compter ou

les emballer), vous devez veiller à ce que votre corps soit électriquement relié à la terre. Pour cela,

portez un bracelet conducteur. Reliez le bracelet à une résistance de 1MΩ et celle-ci à la terre par

l'intermédiaire d'un conducteur.

(3) Veillez en outre à ce que vos vêtements ne viennent jamais en contact avec le composant même si

votre corps est relié à la terre.

(4) Déposez le composant sur une surface métallique correctement mise à la terre.

(5) Sous aucun prétexte, n'omettez de couper l'alimentation avant de procéder à une réparation sur un

circuit imprimé. Par ailleurs, l'intervention sur le circuit imprimé doit se faire alors que celui-ci repose

sur une surface métallique mise à la masse.

H

IT

A

C

H

I IC

4

0

1

T

H

1

,

1

8

U

V

Fig. 1 Emballage conducteur

Sac en polyvinyle

conducteur

C.I.

Eponge

conductrice

Fig. 2 Mise à la terre du corps

Bracelet de mise à la terre du corps

(Bande conductrice Elimik)

Pince de connexion avec

fil de mise à la terre

1MΩ

– 4 –

(6) Use a three wire type soldering iron including a grounding wire.

Fig.4 Grounding a solder iron

Use a high insulation mode (100V, 10MΩ or higher) when ordinary iron is to be used.

(7) In checking circuits for maintenance, inspection, or some others, be careful not to have the test probes

of the measuring instrument shortcircuit a load circuit or the like.

Bare copper wire (for body earth)

Metal plate (of Al. stainless steel, etc.)

Working table

Resistor 1MΩ(1/2W)

Earth wirte

Staple

Fig.3 Grounding of the working table

soldering iron

Grounding wire

Screw stop at the screwed

part using a rag plate

– 5 –

(6) Le fer à souder doit être alimenté par un câble à trois conducteurs (dont un pour la mise à la terre).

Fig.4 Mise à la terre d'un fer à souder

Vous pouvez également utiliser un fer à souder ordinaire dans la mesure où il est parfaitement

isolé (au moins 10MΩ sous 100V).

(7) Pendant le contrôle des circuits au cours des opérations d'entretien ou d'inspection, évitez à tout prix la

mise en court-circuit de la charge par les pointes de contact de l'appareil de mesure.

Fil de cuivre nu

(pour mise à la

terre du corps)

Surface métallique (aluminium, acier inoxydable, etc.)

Plan de travail

Résistance de

1MΩ (1/2W)

Câble de masse

Agrafe

Fig.3 Mise à la terre d'un plan de travail

fer à souder

Câble de masse

Poser ici une rondelle éventail et la visser

– 6 –

1. In quiet operation or stopping the running, its heard slight flowing noise of

refrigerant in the refrigerating cycle occasionally, but this noise is not abnormal

for the operation.

2. When it thunders near by, it is recommend to stop the operation and to

disconnect the power cord plug from the power outlet for safety.

3. The room air conditioner dose not start automaticaly after recovery of the

electric power failure for preventing fuse blowing. Re-press START / STOP

button after 3 minutes from when unit stopped.

4. If the room air conditioner is stopped by adjusting thermostat, or missoperation,

and re-start in a moment, there is occasion that the cooling and heating

operation does not start for 3 minutes, it is not abnormal and this is the result

of the operation of IC delay circuit. This IC delay circuit ensures that there is

no danger of blowing fuse or damaging parts even if operation is restarted

accidentally.

5. This room air conditioner should not be used at the cooling operation when the

outside temperature is below 22˚C (72˚F).

6. This room air conditioner (the reverse cycle) should not be used when the

outside temperature is below –20˚C (–4˚F).

If the reverse cycle is used under this condition, the outside heat exchanger is

frosted and efficiency falls.

7. When the outside heat exchanger is frosted, the front is melted by operating

the hot gas system, it is not trouble that at this time fan stops and the vapour

may rise from the outside heat exchanger.

CAUTION

– 7 –

1. Dans certaines conditions et pendant un arrêt de fonctionnement, on peut

parfois entendre le bruit du réfrigérant circulant dans les canalisations; ce bruit

n'a rien d'anormal.

2. Pour des raisons de sécurité, il est conseillé, pendant un orage, d'arrêter le

fonctionnement du système en coupant l'alimentation électrique.

3. Pour éviter que le fusible ne fonde, le climatiseur ne démarre pas

automatiquement après une panne de secteur. La remise en marche suppose

une pression sur la touche START / STOP après un délai d'au moins 3 minutes

suivant l'arrêt.

4. Si le climatiseur est arrêté à la suite d'un réglage de thermostat, ou à cause

d'une fausse manoeuvre et qu'il est remis en route, il se peut que la

réfrigération ou le chauffage ne reprenne qu'après 3 minutes. Ce phénomène

est normal et dû à un relais temporisé. Ce relais temporisé a pour rôle

d'éviter que le fusible ne fonde ou que des composants ne soient

endommagés par une remise en service accidentelle.

5. Ce climatiseur ne doit pas être utilisé pour réfrigérer une pièce lorsque la

température extérieure est inférieure à 22˚C (72˚F).

6. Ce climatiseur ne doit pas être utilisé lorsque la température extérieure est

inférieure à –20˚C (–4˚F).

En effet, dans ce cas, l'échangeur de chaleur extérieur gèle et le rendement

chute considérablement.

7. Quand l'échangeur de chaleur extérieur est givré, les gaz chauds peuvent

entraîner une vaporisation de l'eau accumulée sur la face avant. Ce n'est pas

un problème si à ce moment-là le ventilateur s'arrête et il se peut que de la

vapeur se dégage de l'échangeur de chaleur extérieur.

ATTENTION

– 8 –

MODEL

FAN MOTOR

FAN MOTOR CAPACITOR

FAN MOTOR PROTECTOR

COMPRESSOR

OVER HEAT PROTECTOR

OVERLOAD RELAY

FUSE (for MICRO COMPUTER)

POWER RELAY, STICK RELAY

POWER SWITCH

TEMPORARY SWITCH

TEST SWITCH

TRANSFORMER

VARISTOR

NOISE SUPPRESSOR

THERMOSTAT

REFRIGERANT CHARGING VOLUME

(R410A)

CHARGE EN RÉFRIGÉRANT

(R410A)

UNIT UNITÉ

PIPES

CANALISATIONS

(MAX. 20m)

SPECIFICATIONS CARACTERISTIQUES GENERALES

MODÈLE

MOTEUR DE VENTILATEUR

COMPRESSEUR

RELAIS DE SURCHARGE

INTERRUPTEUR D'ALIMENTATION

INTERRUPTEUR AUXILIAIRE

INTERRUPTEUR DE TEST

TRANSFORMATEUR

VARISTANCE

ANTIPARASITAGE

THERMOSTAT

CONDENSATEUR DE MOTEUR

DE VENTILATEUR

PROTECTION DU MOTEUR

DE VENTILATEUR

PROTECTION CONTRE LES

SURCHAUFFES

FUSIBLE

(pour MICROPROCESSEUR)

RELAIS DE PUISSANCE,

RELAIS AUTOEXCITE

REMOTE CONTROL SWITCH (LIQUID CRYSTAL)

INTERRUPTEUR DE TÉLÉCOMMANDE (CRISTAUX LIQUIDES)

YES (RAR-3R5)

OUI (RAR-3R5)

NO

NON

FUSE CAPACITY

CALIBRE DE FUSIBLE

30W (DC280V)

NO NON

3A

G4AS

YES OUI

NO NON

450NR

NO NON

YES (IC) OUI (IC)

47W (DC380V)

EU1013E1

YES OUI

25A, 2A, 1A

NO NON

YES OUI

NO NON

450NR, TND05V

NO NON

WITHOUT REFRIGERANT BECAUSE COUPLING

IS FLARE TYPE.

SANS RÉFRIGÉRANT EN RAISON DU

RACCORDEMENT FLARE.

A INRUSH - WITH STAND TYPE

A RETARDE-AVEC STAND TYPE

NO NON

1,190g

RAS-18SX8 RAC-18SX8

– 9 –

HOW TO USE

MODEL RAS-18SX8 / RAC-18SX8

– 2 –

• Please read the “Safety Precaution” carefully before operating the unit to ensure correct usage of the unit.

• Pay special attention to signs of “

Warning” and “ Caution”. The “Warning” section contains matters which, if

not observed strictly, may cause death or serious injury. The “Caution” section contains matters which may result

in serious consequences if not observed properly. Please observe all instructions strictly to ensure safety.

• The signs indicate the following meanings. (The following are examples of signs. )

• Please keep this manual after reading.

PRECAUTIONS DURING OPERATION

WARNING

SAFETY PRECAUTION

• Do not reconstruct the unit.

Water leakage, fault, short circuit or ﬁ re may occur if you reconstruct the unit by

yourself.

• Please ask your sales agent or qualified technician for the installation of your unit.

Water leakage, short circuit or fire may occur if you install the unit by yourself.

• Please use earth line.

Do not place the earth line near water or gas pipes, lightning-conductor, or the

earth line of telephone. Improper installation of earth line may cause electric

shock or ﬁ re.

• Be sure to use the speciﬁ ed piping set for R410A. Otherwise, this may result in

broken copper pipes or faults.

• A circuit breaker should be installed depending on the mounting site of the unit.

Without a circuit breaker, the danger of electric shock exists.

• Do not install the unit near a location where there is ﬂ ammable gas. The outdoor

unit may catch ﬁ re if ﬂ ammable gas leaks around it. Piping shall be suitable

supported with a maximum spacing of 1m between the supports.

• Please ensure smooth ﬂ ow of water when installing the drain hose.

• Make sure that a single phase 220-230V power source is used.

The use of other power sources may cause electrical components to overheat

and lead to ﬁ re.

PRECAUTIONS DURING INSTALLATION

PROHIBITION

CONNECT EARTH LINE

PROHIBITION

WARNING

CAUTION

• Avoid an extended period of direct airﬂ ow for your health.

• Should abnormal situation arise (like burning smell), please stop operating the

unit and remove plug from the socket. Contact your agent. Fault, short circuit or

ﬁ re may occur if you continue to operate the unit under abnormal situation.

• Please contact your agent for maintenance. Improper self maintenance may cause electric

shock and ﬁ re.

• Please contact your agent if you need to remove and reinstall the unit. Electric shock or ﬁ re

may occur if you remove and reinstall the unit yourself improperly.

PRECAUTIONS DURING SHIFTING OR MAINTENANCE

• Do not use any conductor as fuse wire, this could cause fatal accident.

• During thunder storm, disconnect the plug top and turn off the circuit

breaker.

• Do not put objects like thin rods into the panel of blower and suction side

because the high-speed fan inside may cause danger.

• Spray cans and other combustibles should not be located within a meter of the

air outlets of both indoor and outdoor units.

As a spray can’s internal pressure can be increased by hot air, a rupture may result.

PROHIBITION

“OFF”

This sign in the ﬁ gure indicates prohibition. Indicates the instructions that must be followed.

PROHIBITION

– 3 –

ENGLISH

• Do not place plants directly under the airﬂ ow as it is bad for the plants.

• Do not direct the cool air coming out from the air-conditioner panel to face

household heating apparatus as this may affect the working of apparatus such

as the electric kettle, oven etc.

• The product shall be operated under the manufacturer speciﬁ cation and not

for any other intended use.

PRECAUTIONS DURING OPERATION

CAUTION

• Do not attempt to operate the unit with wet hands, this could cause fatal

accident.

• When operating the unit with burning equipments, regularly ventilate

the room to avoid oxygen insufﬁ ciency.

• Please ensure that outdoor mounting frame is always stable, ﬁ rm and without

defect. If not, the outdoor unit may collapse and cause danger.

• Do not wash the unit with water or place a water container such as a vase on

the indoor unit.

Electrical leakage could be present and cause electric shock.

• Be sure to stop the operation by using the remote controller and turn off the

circuit breaker during cleaning, the high-speed fan inside the unit may cause

danger.

• Tu rn off the circuit breaker if the unit is not be operated for a long period.

• Do not climb on the outdoor unit or put objects on it.

• When operating the unit with the door and windows opened, (the room

humidity is always above 80%) and with the air deﬂ ector facing down or moving

automatically for a long period of time, water will condense on the air deﬂ ector

and drips down occasionally. This will wet your furniture. Therefore, do not

operate under such condition for a long time.

• If the amount of heat in the room is above the cooling or heating capability of

the unit (for example: more people entering the room, using heating equipments

and etc.), the preset room temperature cannot be achieved.

• Indoor unit cleaning must be performed by authorized personnel only. Consult

your sales agent.

Using a commercially available detergent or similar can damage the plastic

parts or clog the drain pipe, causing water to drip with potential electric shock

hazard.

• Do not touch the air outlet, bottom surface and aluminium ﬁ n of the outdoor

unit.

You may get hurt.

• Do not touch the refrigerant pipe and connecting valve.

Burns may result.

PROHIBITION

DON’T WET

PROHIBITION

DON’T TOUCH

“OFF”

PROHIBITION

DON’T TOUCH

STRICTLY OBSERVE

PRECAUTIONS

“OFF”

– 10 –

– 4 –

INDOOR UNIT

OUTDOOR UNIT

Micro Mesh Stainless Filter (internal)

Catches dusts in the air. (Page 37)

Titanium Heat Exchanger (internal)

Movable Panel

This panel opens during the operation and closes

when operation stop.

(It may not open on certain operation mode.)

Signal Receiver (internal)

Receive signal from the

remote control.

Indicator

Front Panel

(Page 8)

Horizontal/Vertical Air Deflector (internal)

Air Outlet

Remote Controller

Pipe/Wiring

Drain Hose

Drains dehumidified water generated from the indoor unit when in

the cooling, dehumidifying and dry cool modes.

Air Inlet (rear and left side)

Earth Terminal

(side bottom)

Drain Port (bottom)

Air Outlet

Discharges cool air when in heating

mode and warm air when in cooling

and dry cool modes, and warm or

cold air when in the dehumidifying

mode.

Remote Controller Holder

To fix the remote controller

on the wall or pillar.

• Even if the operation is stopped, the outdoor

to cool down the electrical parts.

• In heating operation, condensed water and

defrosted water is discharged from the outdoor

unit. Do not block the drain port as the water in

the drain may freeze in a cold area.

• Even during cooling operation, the water

condensed in the pipe, etc. may flow out from

the outdoor unit.

• When installing the outdoor unit under eaves,

etc. of the apartment, install a bush and drain

pipe on the drain port for drainage treatment.

ABOUT OUTDOOR UNIT

(Understanding The Operating Mechanism, page 43)

NAMES AND FUNCTIONS OF EACH PART

unit fan continues to rotate for 10-60 seconds

– 5 –

ENGLISH

( )

INDOOR UNIT CONTROL PANEL / CLEANING UNIT

Open the front panel to operate. (How to open the front panel, page 8)

Anti-mold Wasabi Cassette

Releases anti-mold elements

with wasabi fragrance to

prevent mold from growing

on dust inside the dust box.

(Page 8)

Dust Catcher

Collects the dust swept by

the cleaning unit. (At front

and top.) (Page 39)

Front Panel

Electric Dust Collector

Electrode

Releases negative ions to catch

pollens and dust in the air.

(Page 42)

Cleaning Unit

Cleans the dust

caught by the micro

mesh stainless filter.

Electric Dust

Collector Electrode

Ionized Mist Generator

(Located inside the air outlet.)

(Page 42)

Air Quality Sensor

Detects pollution of air (such as cigarette

smoke) when the air quality monitoring

operation is set. (Page 21)

Temporary Switch (Force-Cool switch)

If the remote controller does not

work due to battery failure,

press this switch to start

operation. (Page 49)

Force-cooling operation starts if this

switch is pressed for more than

5 seconds. This operation is allowed

to sales agents only. Users must not

perform this operation. (Page 49)

Dust Box

Collects and keeps the dust

that has been cleaned.

(Page 36)

Dust is collected

in this portion.

• While the power is on, a very small amount of power is

consumed within the control circuit even when the unit

is not in operation.

Power can be saved if the circuit breaker is switched off.

CAUTION

Pull out the power plug if the unit is not in

use for a long period.

(Or turn off the circuit breaker.)

– 11 –

– 6 –

REMOTE CONTROLLER

Tr ansmits the operation and timer settings to the indoor unit.

The LCD shown in the illustration below is the display immediately after the reset switch is pressed. Usually not

all the data are displayed. On the LCD shown below, the functions not available for this room air conditioner are

also displayed.

Tr ansmission Part

Tr ansmission Indicator

The transmission indicator

lit when a signal is sent.

ROOM TEMPERATURE

Button

Press this button to set the

room temperature. Keep

pressing and the value will

change more quickly.

(Page 13, 14)

HUMIDITY Button

Press this button to set the

humidity for dehumidify and

dry cool operations.

(Page 14)

START/STOP Button

Press this button to start

operation. Press again to stop

operation.

HEAT Button

Press this button to start

heating operation.

(Page 15)

DEHUMIDIFY Button

Press this button to start

dehumidifying operation.

(Page 15)

COOL Button

Press this button to start

cooling operation.

(Page 17)

DRY COOL Button

Press this button to start dry

cool operation. (Page 17)

BUTTONS TO

START OPERATIONS

Remote controller can be used when it is fixed on a wall or pillar using the remote controller holder.

Before fixing it, make sure the indoor unit can be controlled from the remote controller fixing point.

Attach the remote controller

• Insert from above.

Take out the remote controller

• To remove, hold the upper part

of the remote controller and

pull it up.

• Do not remove the remote

controller by twisting it left

and right. Doing so could

result in coming off of the

rear cover.

PROHIBITION

SLEEP TIMER Operation Button

Press this button to start sleep timer

operation. (Page 31)

IONIZED MIST Operation Button

Press this button to start ionized mist

operation. (Page 18)

Screw

NAMES AND FUNCTIONS OF EACH PART (continued)

– 7 –

ENGLISH

RAR-3R5

(When the door is open)

Operation Selector

Press this button to select the

operation mode. (Page 13, 14)

VERTICAL AIRFLOW Button

Use this button to swing the

vertical air deflector or to adjust

the angle to your preference.

(Page 25)

HORIZONTAL AIRFLOW

Button

Use this button to swing the

horizontal air deflector or

to adjust the angle to your

preference. (Page 26, 27)

PREFERENCE Button

Press this button to select your

preferred mode. (Page 23, 24)

TIMER Buttons

SET TIME Button

Use this button to set and

check the current time.

(Page 11)

RESET Button

Press this button after the

batteries are replaced and

when the air conditioner does

not function properly. (Page 11)

MANUAL CLEAN Button

Starts filter cleaning operation

while the air conditioner

operation is stopped. (Page 34)

AIR PURIFYING Button

Press this button to start

stainless plasma air purifying

(FAN) operation.

(Page 18)

BUTTONS TO

START OPERATIONS

FAN SPEED Button

Press this button to select

fan speed. (Page 13, 14)

These are preset functions

except for

(SAVE).

Preset can be done if these

buttons are pressed while the

air conditioner is stopped,

however, the unit will not

function accordingly.

FUNCTION SELECTOR

Buttons

Each time when you press,

blinking changes in the

following sequence (page 12,

19, 20, 21, 22):

ON/OFF Button

Use this button to set or cancel

the function selected by the

function selector.

FUNCTION SELECTOR

– 12 –

– 8 –

Open the front panel.

• Do not hold the movable panel

when opening and closing the

front panel.

Movable panel

Front panel

Gripping part

Panel support

• Hold and lift up the front panel.

• Push up the panel support until it

clicks to lock it.

• Lower the front panel and fix in

position with the panel support.

CAUTION

•

Do not use excessive force to open and close the movable

panel.

This may cause it to malfunction.

(The movable panel automatically open and close when the power

is ON/OFF and START/STOP.

)

•

Do not open the front panel during operation

.

It may interrupt the movable panel to work properly. Be sure to stop

the operation first before opening the front panel.

Install the anti-mold wasabi cassette.

• Pull out the anti-mold wasabi

cassette case.

• Take out the anti-mold wasabi

cassette from the aluminium bag.

Anti-mold wasabi

cassette

Aluminium bag

Anti-mold wasabi

cassette case

• Hold the anti-mold wasabi

cassette with the handle

side toward you, and then

install it into the unit.

• Slide the anti-mold

wasabi cassette that

has been taken out of

the wrapper directly

into the anti-mold

wasabi cassette case.

Do not remove or tear

the aluminium sheet on

the surface nor make a

hole on it.

CAUTION

• Do not put your face close to the package when you

open it.

Your eyes or nose may be irritated by wasabi aroma.

• Do NOT eat.

1

2

No daily maintenance is required. However,

the effectiveness of anti-mold wasabi cassette

will be lost after approximately 10 years have

elapsed. Replace the anti-mold wasabi cassette

in such event.

INSTALLING ANTI-MOLD WASABI CASSETTE

– 9 –

ENGLISH

1 12

Close the front panel.

• Hold and lift up the front panel.

CAUTION

• If the front panel is not closed properly, the (CLEAN) indicator

blinks during filter cleaning operation and stainless plasma air

purifying operation. These operations will not perform properly if the

front panel is not closed securely. Also, the movable panel will not

work properly on cooling operation, etc.

• If the front panel is loose, it may come off and drop.

• When opening the front panel upwards, please do not use excessive force.

If the front panel comes off the device, this may cause it to malfunction.

• When the front panel remains open, be sure to push up the panel

support.

• Push down the panel support until it clicks.

• Push the both ends of the front panel first and

then its center until it clicks.

• Pull it downward.

3

Front panel

Movable panel

– 13 –

– 10 –

Make sure the power plug is firmly plugged into the power outlet.

WARNING

• Be sure to use the power outlet exclusively for

air conditioner

Use of other power outlet may cause heat, which

could result in fire.

• Make sure that dust is not deposited on the

power plug and be sure to plug in until the blades

of the plug are fully inserted to avoid unstable

plug-in and dust from being accumulated

Use of air conditioner with dusty power plug or

improper power connection could result in electrical

shock or fire.

CAUTION

Do not operate with

wet hands

It may cause electric

shock.

Compulsory

Wet Hand

Prohibited

Performing operation check after the power is turned on.

Perform the filter cleaning unit operation check

• After the power is turned on (after the power plug is inserted into the power outlet or

after the circuit breaker is switched on after power failure), the cleaning unit makes

one cycle of back and forth movement.

• At this time, the

(CLEAN) indicator is lit.

• One cycle of operation check will take approximately 7 minutes.

• During the operation check, the unit performs “Fan” operation while the movable panel and

horizontal air deflector remain closed.

• If the

(CLEAN) indicator blinks (lit for 4 seconds/off 1 second) after the operation check,

refer to “Troubleshooting” on page 45.

Cleaning Unit

There is a filter

cleaning wiper inside.

Dust catcher

CAUTION

Do not put your fingers or a stick etc into the top surface during

the filter cleaning operation

It may result in injury or malfunction.

• The illustration shows the unit without front panel for your reference

only.

During the actual operation, the filter cleaning is not performed if

the front panel is open.

1

2

Compulsory

FILTER CLEANING UNIT OPERATION CHECK

– 11 –

ENGLISH

Address

RAR-3R5

Install the batteries.

• Use two AAA-size alkaline batteries.

Set the current time (Ex: set to 1:30 p.m.)

RESET

1

2

Press the (TIMER) button to adjust to the current time.

• You can fast forward the time by continuously pressing the

button.

Confirm the current time

• Press the

(SET TIME) button to check the current time. If

necessary, readjust the time following the above procedure and

.

• Address selector switch is used to prevent

remote controller signal interference in such

circumstance where 2 indoor units are used in

the same room. This switch is not usually used.

(The factory setting is at “A” side.)

For this setting, please make an inquiry to your

sales agent.

Address selector

switch

Switch lever

Remote controller

backside

Do not operate by yourself.

Push mark

and pull.

ABOUT ADDRESS SELECTOR SWITCH

Time is incremented

Time is decremented

Press

(SET TIME) button to set the current time.

• “AM” or “PM” is lit instead of

blinking. It automatically goes

off in 10 seconds.

1

2

Open the cover and press the RESET

button with a sharp tip item.

3

• 18:88 lights up on the current

time display and “AM” and

“PM” start blinking.

CAUTION

1. Do not mix new and old batteries, or

different type of batteries together.

2. Remove the batteries when you do

not use the remote controller for 2 or 3

months.

PREPARE THE REMOTE CONTROLLER

– 14 –

– 12 –

RAR-3R5

1

While (SAVE) is blinking, point the remote controller towards

the unit and press the

(ON/OFF) button.

• A short beep sounds and

(SAVE) indicator turns on.

Press the

(FUNCTION SELECTOR)

button until

(SAVE) blinks.

Press the

(FUNCTION SELECTOR) button again until

(SAVE) blinks.

While

(SAVE) is blinking, point the remote controller towards

the unit and press the

(ON/OFF) button.

• A short beep sounds and

(SAVE) indicator turns off, indicates

the setting is released.

Notes for “save” setting

• If ampere is set to “Save”, the maximum heating capacity slightly lowers

and starting up of heating operation will take a little longer. Besides,

the preset temperature may not be reached if outside temperature is

low. (If ampere is set to

(SAVE), the air conditioner will be in limited

operation at 6(A)).

• Point the remote controller to the signal receiver of the unit

Signal reception distance is approximately 7m in front of the unit.

However, this distance may be shorter or the signal may not be

receivable if there is an electronic lighting device in the same room.

• Handle the remote controller with care

Dropping it or getting it wet may compromise its signal transmission

capability. After new batteries are inserted into the remote controller,

the unit require approximately 10 seconds before it can respond to

commands and begin operation.

WHEN OPERATING THE REMOTE CONTROLLER

Approximately

7m from the front

Ampere setting (Standard/Save) can be selected.

If you experience frequent circuit breaker tripping, set ampere to “Save” to avoid this problem.

(Ampere is set to “Standard” at the time of purchase.)

4

2

RELEASE

PREPARE THE REMOTE CONTROLLER (continued)

– 13 –

ENGLISH

• Performs heating operation when the room temperature is below 23°C.

Set the temperature to be around 23°C.

• Performs dehumidifying operation when the room temperature is 23-26°C.

The preset temperature will be the room temperature at the time of start of air conditioner

operation.

• Performs cooling operation when the room temperature is above 27°C.

Set the temperature to be around 27°C.

RAR-3R5

Press the (OPERATION SELECTOR) button

to set the operation mode to auto.

• Every time you press it, the mode will change as

shown in the chart on the right.

Press the

(START/STOP) button.

Based on the room temperature and outside temperature, the unit determines the most suitable operation

mode (heating, dehumidifying or cooling) and a comfortable temperature. (Set the current time on the remote

controller before starting operation.)

Press the

(START/STOP) button again.

• A short beep sounds and the automatic

operation stops.

• Operation mode will be displayed on the

remote controller display.

Adjust the room temperature

Press the (ROOM TEMPERATURE)

button.

• Every time you press it, a short beep sounds and the

temperature will change by 1°C.

• is displayed if the temperature is set higher than

the automatically set room temperature by 1°C.

is displayed if the temperature is set lower than the

automatically set room temperature by 1°C.

• The adjustable temperature range is not higher or lower

than 3°C of the automatically set room temperature.

• Humidity setting cannot be adjusted.

Increase

Decrease

B

eep

Room temperature and fan speed can be adjusted to your preference.

Select the fan speed

Press the (FAN SPEED) button.

• “AUTO”, “LOW” and “SILENT”

can be selected.

• Every time you press it, the

mode will change as shown in

the chart on the right.

1

2

1

2

STOP

AUTOMATIC OPERATION

Heating

Dehumidifying

Cooling

Even if dehumidifying operation is set, the air conditioner may not execute dehumidifying if the room humidity

is not very high. This is not a malfunction.

AUTOMATIC OPERATION

– 15 –

– 14 –

RAR-3R5

Select the operation mode.

Press the (OPERATION

SELECTOR) button.

•

Any one of Heating/Dehumidifying/

Cooling/Dry Cool/Auto can be selected.

• To start fan operation, perform

stainless plasma air purifying

(FAN) operation. (Page 18)

•

If the (OPERATION SELECTOR)

button is pressed during operation,

a double short beep is heard on auto

mode while a single short beep is

heard on other mode.

Set the fan speed.

Set the room temperature.

Set the humidity (only for

dehumidifying and dry cool modes).

Operation starts.

Press the (START/STOP) button.

Press the

(START/STOP) button again.

• A short beep sounds and the operation stops.

• From next time, the operation that has been set on the above procedure -

can be performed just by pressing the

(START/STOP) button.

Humidity setting range

40-70%

Remote controller temperature setting range

Heating, Cooling, Dry Cool 16-32° C

Dehumidifying 10-32°C

2

1

One of them lights up. One of them lights up.

Press the (HUMIDITY) button.

• The humidity can be set in

increments of 5%.

• Humidity indication disappears in

approximately 10 seconds if the

operation is not started.

Increase

Decrease

4

3

Lights up.

5

STOP

•

Outdoor temperature -20°C-21°C

(When it is below

-20°C

or over 24°C, the heating

function may not operate in order to protect the

device.)

Heating Dehumidifying Dry Cool Cooling

•

Outdoor temperature

1°C-35°C

(Operation does not start if the

room temperature is below 1°C. )

• Outdoor

temperature

25°C-35°C

• Outdoor

temperature

22°C-43°C

• Do not use cooling operation in winter.

Press the (FAN SPEED) button.

• Any one of “AUTO”, “HI”, “MED”,

“LOW”, “SILENT” can be selected.

Fan speed indication disappears

in approximately 10 seconds if the

operation is not started.

• If the

(FAN SPEED) button is

pressed during operation, a double

short beep is heard on auto mode

while a single short beep is heard

on other mode.

Press the (ROOM

TEMPERATURE) button.

•

Room temperature indication

disappears in approximately 10 seconds

if the operation is not started.

• If the (ROOM TEMPERATURE)

button is pressed during operation,

a double short beep is heard at

20°C, a triple short beep at 30°C,

and a single short beep on other

temperature.

Increase

Decrease

Use the air conditioner following the operation conditions outlined below.

MANUAL OPERATION (HEATING, DEHUMIDIFYING, COOLING, DRY COOL)

– 15 –

ENGLISH

( (MIST/AIR

PURIFYING) indicators also

turn on during quick laundry

operation.)

Press the (HEAT) button to start heating operation.

3 types of dehumidifying operations can be performed by pressing the

(DEHUMIDIFY) button.

Performs powerful dry operation without lower down the room temperature.

Condensation

Control

• In auto dehumidifying mode, fine adjustment of room temperature (page 13),

humidity adjustment and fan speed selection (page 14) can be made to your

preference. Every time you press the ROOM TEMPERATURE button, the temperature

will change by 1°C. (Temperature setting range is not higher or lower than 3°C.) Every

time you press the HUMIDITY button, the humidity will change by 5%. (Humidity setting

range is 40%-70%.)

• In quick laundry mode, fine adjustment of room temperature (page 13) and fan

speed selection (page 14) can be made to your preference. (Fine adjustment of

room temperature and humidity adjustment cannot be made in condensation

control mode.)

Press the

(HEAT) button.

• Adjust the room temperature and fan speed to your preference.

Temperature range between 16°C-32°C can be set. (Page 14)

Press the

(START/STOP) button.

• A short beep sounds and heating operation stops.

Press the

(DEHUMIDIFY) button.

• Every time you press the

(DEHUMIDIFY) button, the

mode will change as shown in the chart below.

Press the

(START/STOP) button.

• A short beep sounds and dehumidifying operation stops.

• After the dehumidifying operation is stopped, the remote controller will display

the operation mode that had been set before the

(DEHUMIDIFY) button was

pressed.

(“AUTO” flashes for 5 seconds)

Auto

Dehumidifying

Quick

Laundry

STOP

HEATING OPERATION

DEHUMIDIFYING OPERATION

– 16 –

Auto

Dehumidifying

Operation mode In this situation Operating mechanism

• In damp

weather

• In most of the cases, the room temperature at the time the button is

pressed becomes the preset temperature.

(When room temperature is below 12°C, set 13°C. When it is

temperature. When it is above 26°C, set 26°C)

• Ta rget humidity is around 50-60%. If the humidity becomes lower than

the target value, operation stops. If it becomes higher than the target

value, operation resume.

• The operation mode may automatically be switched to cooling or

heating for temperature control. (Refer to table below)

• To dry the

laundry

quickly

• Detects outdoor temperature, room temperature and humidity to

automatically select the most suitable combination of heating and

powerful dehumidifying operations.

• This operation is performed together with stainless plasma air purifying

operation.

• Priority is given to laundry drying.

Be sure use this mode when no one is in the room as the room

temperature and humidity will be high temporarily.

• 3-hour timer function is used for this operation mode.

• When

controlling

condensation

formed on

windows in

winter time

• Be careful when condensation control operation is performed if the outside temperature is low as it will lower the

room temperature.

•

(OFF TIMER) and (ON TIMER) (page 28), which are to be set using clock function, are not available during

dehumidifying (quick laundry and condensation control modes) operation. However, the timer (for 30 minutes

and 1-9 hours) can be set for quick laundry and condensation control modes with the

(SLEEP) button.

• To set to your desired temperature and humidity while executing dehumidifying, it is recommended to use manual

dehumidifying function. (Page 14)

• If you do not wish room temperature to be too high when drying the laundry, use the preference (Powerful) mode

instead of quick laundry mode. (Page 24)

The operation mode may automatically be switched to cooling or heating for temperature control.

At this time, the room humidity may vary by approximately 10%.

Heating

operation

Dehumidifying operation

Operation

stop

Cooling

operation

About 3

°C

Approx. 3°C if outside temp. is

below approx. 32°C.

Approx. 1°C if outside temp. is

above approx. 32°C.

Room temperature set

Current room temperature

1ºC

• To control the condensation, priority is given to the operation for

lowering humidity. Therefore, the room temperature goes down in

this operation mode. The operation stops if the room temperature

becomes 1°C or below.

• 2-hour timer function is used for this operation mode.

Condensation

Control

Quick Laundry

DEHUMIDIFYING OPERATION (continued)

13°C-22°C, set +2°C. When it is below 23°C-26°C, set room

– 17 –

ENGLISH

(“AUTO” flashes for 5 seconds)

Press the (COOL) button to start cooling operation.

When you operates cooling operation with the dry function, press the (DRY COOL) button, the air conditioner

automatically sets temperature and humidity in dry cool mode.

Press the (COOL) button.

• Adjust the room temperature and fan speed to your preference. (Page 14)

Temperature range between 16°C-32°C can be set.

Press the

(START/STOP) button.

• A short beep sounds and dry cool operation stops.

Press the

(DRY COOL) button.

• Adjust the room temperature (page 13) and fan speed (page 14) to your

preference.

• Every time you press the

(ROOM TEMPERATURE) button, the

temperature will change by 1°C.

(Temperature setting range from the auto set temperature is not higher or

lower than 3°C.)

• Humidity setting cannot be adjusted.

Humidity

to be set

Temperature

to be set

Based on the detected outside and room temperature,

the temperature is set on an hourly basis within the range

of 24-28°C.

• Even if the room temperature

reached the preset temperature,

the air conditioner may continue

to operate if the preset humidity

has not been reached.

Dry

intermittent

operation

Dry Cool operation

Operation

stops

Cooling

operation

About 3°C

Approx. 3°C if outside temp. is

below approx. 32°C.

Approx. 1°C if outside temp. is

above approx. 32°C.

Room temperature set Current room temperature

50% when temperature above 27°C is set.

55% when temperature of 26°C is set.

60% when temperature below 25°C is set.

About 1°C

The operation mode may automatically be switched to cooling or heating for temperature control.

If the room temperature is lower than the preset temperature, intermittent operation (repeat of operation state

and stop state) is performed to avoid excessive lowering of temperature and to control the humidity.

Press the

(START/STOP) button.

• A short beep sounds and cooling operation stops.

STOP

COOLING OPERATION

DRY COOL OPERATION

– 17 –

– 18 –

Position of horizontal

air deflector

Wide airflow angle

The angle set for the current

operation mode

• Stainless plasma air purifying and ionized mist operations have an effect of reducing unpleasant smell of the

wall and curtain in the room and controlling bacteria suspended in the air.

• If the ionized mist operation is set while the air conditioner is in operation, the ionized mist operation will

operate together with another operation.

Ionized mist is generated using the air in the room. It may not be generated depending on the temperature

and humidity. (It may take approximately 30 minutes to 1 hour for ionized mist generation. )

• Stainless plasma air purifying (Fan) operation is the combined operation mode of the fan operation and the

electric dust collector operation.

• If the stainless plasma air purifying mode is set while the air conditioner is in basic operation mode, the air

purifying function by the electric dust collector will operate together.

Press the

(START/STOP) button.

• A short beep sounds and ionized mist operation stops.

• Adjust the fan speed to your preference. “HI”, “MED”, “LOW”, “SILENT” can be

selected. (Page 14)

• When only ionized mist operation is set,

(OFF TIMER) and (ON TIMER)

preset cannot be done.

Press the

(IONIZED MIST) button.

Press the

(IONIZED MIST) button.

Press the

(START/STOP) button.

• A short beep sounds and stainless plasma air purifying operation

stops.

Press the

(AIR PURIFYING) button.

Press the

(AIR PURIFYING) button.

• Adjust the fan speed to your preference. “HI”, “MED”, “LOW”, “SILENT” can

be selected. (Page 14)

• When only stainless plasma air purifying operation is set,

(OFF TIMER)

and

(ON TIMER) preset cannot be done.

STOP

CANCEL

during

operation

CANCEL

during

operation

Operation mode

Ionized mist operation only

When operate together with

another operation

IONIZED MIST OPERATION

STAINLESS PLASMA AIR PURIFYING (FAN) OPERATION

– 19 –

ENGLISH

RAR-3R5

Press the (FUNCTION SELECTOR) button again until

(INTERNAL CLEAN) blinks.

While

(INTERNAL CLEAN) is blinking, point the remote controller

towards the unit and press the

(ON/OFF) button.

• A short beep sounds and

(INTERNAL CLEAN) indicator turns off

on the remote controller.

STOP

The internal cleaning operation is automatically performed after cooling, dehumidifying or dry cool operation to

control mold growth by configuring the

(INTERNAL CLEAN) operation. (There is no mold removing function

and disinfecting/sterilizing effect.)

Press the

(FUNCTION SELECTOR) button

until

(INTERNAL CLEAN) blinks.

While

(INTERNAL CLEAN) is blinking, point the remote controller

towards the unit and press the

(ON/OFF) button.

• A short beep sounds and

(INTERNAL CLEAN) indicator turns on

at the remote controller.

• It will automatically stop after 1 hour of operation.

1

2

• Internal cleaning operation is not performed if the duration of cooling, dehumidifying or dry cool operation is

too short (below approximately 10 minutes).

• If the internal cleaning mode is set, the internal cleaning operation will automatically start when cooling,

dehumidifying or dry cool operation is stopped. During internal cleaning, the heating operation and fan operation

(with stainless plasma air purifying) are performed to control the mold growth inside the indoor unit.

• While

(ON TIMER) is set, internal cleaning operation is not performed from 2 hours before the preset

time.

• Internal cleaning operation is not performed if the air conditioner operation is stopped in any of the following

conditions below.

(heating operation, stainless plasma air purifying operation, quick laundry operation and

(OFF TIMER) stop

under condensation control operation, operation stopped by

(SLEEP) button.)

INTERNAL CLEANING OPERATION

– 18 –

– 20 –

By configuring (SLEEP) operation while the sleep timer is set for auto, heating, dehumidifying, cooling and

dry cool modes, the air conditioner supports your comfortable sleeping environment.

Press the (FUNCTION SELECTOR) button again until (SLEEP)

blinks.

While

(SLEEP) is blinking, point the remote controller towards the

unit and press the

(ON/OFF) button.

• A short beep sounds and

(SLEEP) indicator turns off on the remote

controller.

STOP

Press the (FUNCTION SELECTOR) button

until

(SLEEP) blinks.

While

(SLEEP) is blinking, point the remote controller towards the unit

and press the

(ON/OFF) button.

• A short beep sounds and

(SLEEP) indicator turns on on the remote

controller.

1

2

• When in cooling operation, the temperature and humidity will be controlled in combination with dehumidifying

operation.

• When in dehumidifying or dry cool mode, temperature is controlled to a comfortable level with the preset

humidity target level of 60%.

• When in heating operation, temperature is controlled in the same manner as ordinary sleep mode.

• When in automatic operation, a control is executed according to the operation mode set by the auto

function.

SLEEP OPERATION

– 21 –

ENGLISH

RAR-3R5

Press the (FUNCTION SELECTOR) button again until (AIR QUALITY

MONITOR) blinks.

While

(AIR QUALITY MONITOR) is blinking, point the remote controller

towards the unit and press the

(ON/OFF) button.

• A short beep sounds and

(AIR QUALITY MONITOR) indicator turns off

on the remote controller.

• The

(MONITOR) indicator on the indoor unit turns off.

CANCEL

The air quality sensor detects pollution of the air in the room and the air conditioner automatically performs the

stainless plasma air purifying operation in the event the air is not clean.

2

Press the (FUNCTION SELECTOR) button until

(AIR QUALITY MONITOR) blinks.

While

(AIR QUALITY MONITOR) is blinking, point the remote controller

towards the unit and press the

(ON/OFF) button.

• Preset the air quality monitor operation.

• During the air quality monitor operation,

(MONITOR) and (MIST/AIR

PURIFYING) indicators on the indoor unit turn on.

1

RAR-3R5

Press the (START/STOP) button.

Press the

(AIR PURIFYING) button when operation stops.

• Perform the stainless plasma air purifying operation.

• Fan speed can be

(HI), (MED) or (LOW).

Use the

(ROOM TEMPERATURE) button

to select sensitivity.

•

is displayed when sensitivity is increased by 1 level.

•

is displayed when sensitivity is decreased by 1 level.

• Adjustable range is 7 levels from +3 to -3.

• Indication of +3 to -3 turns off in approximately 10 seconds.

Value (sensitivity) can be selected from 7 levels.

STOP

Sensitivity

increase

Sensitivity

decrease

• The air quality sensor detects air pollution includes cigarette smoke, spray (insecticide, etc.) and alcohol.

• When air quality monitoring mode is set during basic air-conditioning operation, air purifying operation is

performed in addition to the basic air-conditioning operation.

• Air quality monitoring operation is a preset function. Even if air quality monitoring is preset, the actual operation

will be performed only when air pollution is detected.

• The setting of air quality monitoring mode is valid for 2 weeks from the last remote control operation.

(If any remote control operation is performed while

(AIR QUALITY MONITOR) is set, the preset air quality

monitoring mode is valid for 2 weeks from such remote control operation.)

Once the above mentioned 2 weeks have elapsed, the

(MONITOR) indicator on the indoor unit turns

off.

(However,

(AIR QUALITY MONITOR) indication on the remote controller remains on. If the (MONITOR)

indicator on the indoor unit is off, please reset or cancel the air quality monitoring mode.)

AIR QUALITY MONITOR OPERATION

La page charge ...

Hitachi RAC-18SX8 Manuel utilisateur

Hitachi RAC-18SX8 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents