Hitachi RAK-25PED Manuel utilisateur

SPLIT

TYPE AIR CONDITIONER

INDOOR UNIT/OUTDOOR UNIT

This room air conditioner is only for consumer usage.

Do not use for preservation of foods, animals, plants, precision machines, art, medicine or such.

Instruction manual Page 1~10

To obtain the best performance and ensure years of

trouble free use, please read this instruction manual

completely.

MODEL

RAK-18PED/RAC-18WED

RAK-35PED/RAC-35WED

RAK-50PED/RAC-50WED

RAK-25PED/RAC-25WED

RAK-35PEDC/RAC-35WED

RAK-50PEDC/RAC-50WED

RAK-25PEDC/RAC-25WED

INDOOR UNIT

OUTDOOR UNIT

RAK-18PED

RAK-25PED

RAK-35PED

RAK-50PED

RAK-25PEDC

RAK-35PEDC

RAK-50PEDC

RAC-18WED

RAC-25WED

RAC-35WED

RAC-50WE

L.H

D

R32

• Please read the “Safety Precaution” carefully before operating the unit to ensure correct usage of the unit.

• Pay special attention to signs of “

Warning” and “ Caution”. The “Warning” section contains matters which, if

not observed strictly, may cause death or serious injury. The “Caution” section contains matters which may result

in serious consequences if not observed properly. Please observe all instructions strictly to ensure safety.

• The signs indicate the following meanings. (The following are examples of signs.)

WARNING

SAFETY PRECAUTION

• Do not reconstruct the unit.

Water leakage, fault, short circuit or fi re may occur if you reconstruct the unit by

yourself.

• Please ask your sales agent or qualified technician for the installation of your unit.

Water leakage, short circuit or fire may occur if you install the unit by yourself.

• Please use earth line.

Do not place the earth line near water or gas pipes, lightning-conductor, or the

earth line of telephone. Improper installation of earth line may cause electric

shock or fire.

• Be sure to use the specif ied piping set for . Otherwise, this may result in

broken copper pipes or faults.

A circuit breaker should be installed depending on the mounting site of the unit.

Without a circuit breaker, the danger of electric shock exists.

Please ensure smooth fl ow of water when installing the drain hose.

Make sure that a single phase power source is used.

The use of other power sources may cause electrical components to overheat

and lead to fi re.

PRECAUTIONS DURING INSTALLATION

PROHIBITION

CONNECT EARTH LINE

PROHIBITION

WARNING

CAUTION

•

• Please contact your agent for maintenance. Improper self maintenance may cause electric

shock and fi re.

• Please contact your agent if you need to remove and reinstall the unit. Electric shock or fi re

may occur if you remove and reinstall the unit yourself improperly.

PRECAUTIONS DURING SHIFTING OR MAINTENANCE

“OFF”

PROHIBITION

220V-230V

 Please keep this manual after reading.

Make sure to connect earth line.

Indicates the instructions that must be followed.

This sign in the figure indicates prohibition.

Do not install the unit near a location where there is flammable gas.

The outdoor unit may catch fire if flammable gas leaks around it.

Should abnormal situation arise (like burning smell), please stop operating the

unit and turn off the circuit breaker. Contact your

fire may occur if you continue to operate the unit

under abnormal situation.

agent. Fault, short circuit or

PRECAUTIONS DURING OPERATION

WARNING

Ь

Ь Do not use any conductor as fuse wire, this could cause fatal accident.

Ь During thunder storm, disconnect the plug top and turn off the circuit

breaker.

Ь Do not put objects like thin rods into the panel of blower and suction side

because the high-speed fan inside may cause danger.

Ь Spray cans and other combustibles should not be located within a meter of the

air outlets of both indoor and outdoor units.

As a spray can’s internal pressure can be increased by hot air, a rupture may result.

PROHIBITION

“OFF”

Avoid an extended period of direct airflow for your health.



• Do not use refrigerant other than the one indicated on the outdoor unit (R32) when installing,

Using other refrigerants may cause trouble or damage to the unit, and personal injury.

moving or repairing.

. Otherwise, this may result in

R32

This appliance is filled with R32.

Ь .stnalp eht rof dab si ti sa wo lfria eht rednu yltcerid stnalp ecalp ton oD

Ь Do not direct the cool air coming out from the air-conditioner panel to face

household heating apparatus as this may affect the working of apparatus such

as the electric kettle, oven etc.

Ь ton dna noitac ifice

ps rerutcafunam eht rednu detarepo eb llahs tcudorp ehT

for any other intended use.

PRECAUTIONS DURING OPERATION

CAUTION

Ь Do not attempt to operate the unit with wet hands, this could cause fatal

accident.

Ь When operating the unit with burning equipments, regularly ventilate

.ycneic iffusni negyxo diova ot moor eht

Ь tuohtiw dna mr if ,elbats syawla si emarf gnitnuom rood

tuo taht erusne esaelP

defect. If not, the outdoor unit may collapse and cause danger.

Ь Do not wash the unit with water or place a water container such as a vase on

the indoor unit.

Electrical leakage could be present and cause electric shock.

Ь Be sure to stop the operation by using the remote controller and turn off the

circuit breaker during cleaning, the high-speed fan inside the unit may cause

danger.

Ь Turn off the circuit breaker if the unit is not be operated for a long period.

Ь Do not climb on the outdoor unit or put objects on it.

Ь When operating the unit with the door and windows opened, (the room

gnivom ro nwod gnicaf rotce lfed ria eht htiw dna )%08 evoba sy

awla si ytidimuh

automatically for a long period of time, water will condense on the air deflector

and drips down occasionally. This will wet your furniture. Therefore, do not

operate under such condition for a long time.

Ь If the amount of heat in the room is above the cooling or heating capability of

the unit (for example: more people entering the room, using heating equipments

and etc.), the preset room temperature cannot be achieved.

Ь Indoor unit cleaning must be performed by authorized personnel only. Consult

your sales agent.

Using a commercially available detergent or similar can damage the plastic parts

or clog the drain pipe, causing water to drip with potential electric shock hazard.

Ь roodtuo eht fo n if muinimula dna ecafrus mottob ,teltuo ria eht hcuot

to

n oD

unit.

You may get hurt.

Do not touch the refrigerant pipe and connecting valve.

Burns may result.

PROHIBITION

DON’T WET

PROHIBITION

DON’T TOUCH

“OFF”

PROHIBITION

DON’T TOUCH

STRICTLY OBSERVE

PRECAUTIONS

“OFF”

Ь

This appliance is not to be used by children or persons with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction. Children must be supervised not to play with the appliance.



OPERATING RANGE

Operation mode Cooling / Dehumidifying Heating

C°12 ot 51-C°34 ot 01-erutarepmet roodtuO



Air filter

To prevent dust from coming into the indoor unit.

(Refer page 6)

Front panel

Indoor unit indicators

Light indicator showing the operating condition.

(Refer page 5)

Horizontal deflector Vertical deflector

(Air Outlet)

Remote controller

Send out operation signal to the indoor unit. So as

to operate the whole unit.

NAMES AND FUNCTIONS OF EACH PART

INDOOR UNIT

Drain hose

Drains the dehumidified water from the indoor unit to the

outdoor during “cooling” or “dehumidifying” operation.

Piping and Wiring

Air inlets (Rear and left sides)

OUTDOOR UNIT

Air outlet

When “heating” operation is

performed, cool air blows and

when “cooling” or “dehumidifying”

operation is performed, warm air

blows.

Drain port

Earth terminal

Air outlet

When “heating” operation is

performed, cool air blows and

when “cooling” or “dehumidifying”

operation is performed, warm air

blows.

Drain hose

Drains the dehumidified water from the indoor unit to the

outdoor during “cooling” or “dehumidifying” operation.

Piping and Wiring

Air inlets (Rear and left sides)

MODEL NAME AND DIMENSIONS

Drain port

Earth terminal

About the outdoor unit:

s When “Stop” is selected during operation

of the indoor unit, the fan of the outdoor

unit continues turning for 10 to 60

seconds to cool the electric parts down.

s In heating operation, condensate or

water due to defrosting will flow.

Do not cover the drain port of the outdoor

unit because such water may freeze in

the chilly area.

s When the outdoor unit is hung on the

install the bush and drain pipe

on the drain port and drain water.

780 280 215

27

792 600 299

MODEL WIDTH (mm) HEIGHT (mm) DEPTH (mm)

660 530 8

7) egap refeR(

RAC-18WED

RAC-25WED

RAC-35WED

RAC-50WED

RAK-18/25/35/50PED,RAK-25/35/50PE

RAC-18/25/35WED

DC

wall,

NAMES AND FUNCTIONS OF EACH PART

INDOOR UNIT INDICATIONS

TIMER LAMP (Orange)

This lamp lights when the

timer is working.

OPERATION LAMP (Yellow)

This lamp lights during operation.

The OPERATION LAMP flashes

in the following cases during

heating.

(1) During preheating

For about 2-3 minutes after

starting up.

(2) During defrosting

Defrosting will be performed

about once an hour when frost

forms on the heat exchanger

of the outdoor unit, for 5-10

minutes each time.

TEMPORARY SWITCH

If the power stays on and the unit is not operated, power is slightly consumed in the control circuit.

The power is saved by turning off the power switch (or the circuit breaker when the power is supplied

from the outdoor unit).

CAUTION

Turn off the circuit breaker

if the unit is not be operated

for a long period.

Use this switch to start and stop when the remote

controller does not work.

By pressing the temporary switch, the operation is

done in automatic mode.

When the operation is done using the temporary

switch after the power source is turned off and turn

on again, the operation is done in automatic mode.

– 2 –

NAMES AND FUNCTIONS OF REMOTE CONTROLLER

L.H

■ This controls the operation function and timer setting of the room air conditioner. The range of control

is about 7 meters. lf indoor lighting is controlled electronically, the range of control may be shorter.

Precautions for Use

• Do not put the remote controller under direct sunlight and high temperature.

• Do not drop it on the ﬂ oor, and protect it from water.

• If you press the FUNCTION button during operation, the air conditioner may stop for about 3 minutes

for protection before you can start it again.

Signal Transmission

MODE Button

Select the operation mode.

(

Page 3)

STOP Button

Press this button to stop operation.

ECO Button

Use this button to set the ECO mode.

(

Page 6)

OFF TIMER Button

Select the turn OFF time.

(

Page 4)

ON TIMER Button

Select the turn ON time.

(

Page 4)

Transmission Sign

The transmission sign blinks

when a signal has been send.

POWERFUL Button

Press this button to start

powerful operation. (

Page 4)

TEMPERATURE Button

Room temperature setting.

Value will change quicker when

keep pressing.

(

Page 3)

FAN SPEED Button

Select the fan speed for cooling

and heating mode.

(

Page 3)

AUTO SWING Button

Control the angle of the

horizontal air deﬂ ector.

(

Page 7)

– 3 –

MANUAL OPERATION [Heating • Dehumidify • Cooling]

■ Please use under below condition when you want to set the function mode, room temperature and

fan speed manually.

HEATING DEHUMIDIFYING COOLING

Outdoor Temperature

24˚C below

Room Temperature

16˚C above

Outdoor Temperature

21˚C above

1

2

3

4

OPERATION MODE SELECTION

ROOM TEMPERATURE SETTING

FAN SPEED SETTING

Press the

(STOP) button

• Every time you press the button, the mode will change as the below.

• The cooling operation does not start if the

temperature setting is higher than the current

room temperature.

• Every time you press the button, fan speed will change as

below sequence.

• HEATING :

COOLING

• DEHUMIDIFYING :

• Operation stops with a beep.

L.H

■ Recommend Temperature

Heating 20~24˚C

Dehumidify 20~26˚C

Cooling 25~28˚C

L.H

POWERFUL

: HEATING

: DEHUMIDIFYING

: COOLING

Up

Down

AUTO ÆHIGH ÆMED ÆLOW ÆSILENT

LOW ÆSILENT

}

– 4 –

■ Operation stop at setting time

Timer Reservation

OFF TIME setting

• Select the OFF TIME by pressing the (OFF)

Button.

• Setting time will change according to the below

sequence when you press the button.

1 hour interval

L.H

TIMER RESERVATION

■ ON Timer and OFF Timer are available.

POWERFUL OPERATION

• During POWERFUL operation, cooler or warmer air will be blown out from indoor unit for COOLING or

HEATING operation respectively.

Press the (POWERFUL) button during operation.

• "

" is displayed on the LCD.

POWERFUL operation ends in 20 minutes. Then the system

automatically operates with the previous settings used before

POWERFUL operation.

START

Press the (POWERFUL) button again.

• "

" disappears from the LCD.

CANCEL

L.H

NOTE

• When ECO mode, or LEAVE HOME mode is selected, POWERFUL operation is cancelled.

• During POWERFUL operation, capacity of the air conditioner will not increase

– if the air conditioner is already running at maximum capacity.

– just before defrost operation (when the air conditioner is running in HEATING operation).

• After auto restart, POWERFUL operation is cancelled and previous operation shall start.

2

1

ON TIME setting

• Select the ON TIME by pressing the (ON) Button.

• Setting time will change according to the below

sequence when you press the button.

Timer off

1 hour interval

Timer on

By pressing (POWERFUL) button during HEATING, DEHUMIDIFYING, COOLING

the air

performs at maximum power.

operation,

conditioner

•

– 5 –

LEAVE HOME(LH) OPERATION

■ Prevent the room temperature from falling too much by setting temperature at 10 deg automatically

when no one is at home.

Hold down the HEATING Button for 3-5 seconds to start

Leave Home operation.

• Room temperature is automatically set at 10 deg.

• "

", " LH ", " ", " ", is displayed on the LCD.

START

Press the (STOP) button.

Change to other Operation Mode.

CANCEL

NOTE

• During Leave Home operation, fan speed and horizontal air deﬂ ector position cannot be changed.

L.H

– 6 –

ECO OPERATION

■ Energy saving operation by changing set temperature and by limiting the maximum power consumption

value.

L.H

Press (ECO) button during operation.

• "

" is displayed on the LCD.

• Energy saving operation will start by changing

the set temperature higher or lower and saving

operation power consumption.

START

Press (START/STOP) button.

• Press

(ECO) button again.

• "

" disappears from the LCD.

CANCEL

NOTE

• In case the power consumption is already low,ECO operation will not reduce the power

consumption.

• By pressing (POWERFUL) button, ECO operation is cancelled.

• After auto restart, ECO operation is cancelled and previous operation mode shall start.

By pressing the (ECO) button during Heating,

Dehumidifying or Cooling operation, the air conditioner

performs the “ECO” operation.

– 7 –

ADJUSTING THE AIRFLOW DIRECTION

HOW TO EXCHANGE THE BATTERIES IN THE REMOTE CONTROLLER

2

1

2

Adjust the airﬂ ow upward and downward.

According to operation, the horizontal air deﬂ ector is automatically

set to the proper angle suitable for each operation.The deﬂ ector

can be swings up and down and also set to the desired angle using

the “

(AUTO SWING)” button.

• If the “

(AUTO SWING) ” button is pressed once, the

horizontal air deﬂ ector swings up and down.If the button is

pressed again, the deﬂ ector stops in its current position.

Several seconde (about 6 seconds) may be required before

the deﬂ ector starts to move.

• When the operation is stopped, the horizontal air deﬂ ector

moves and stops at the position where the air outlet closes.

• In “Cooling” operation, do not keep the horizontal air deﬂ ector

swinging for a long time. Some dew may form on the horizontal

air deﬂ ector and some dew may drop from it.

Adjust the airﬂ ow to left and right.

Hold the vertical air deﬂ ector as shown on the right and

adjust the airﬂ ow to left and right.

Remove the cover as shown in the ﬁ gure and take out the old

batteries.

Push and pull to the

dirction of arrow

Install the new batteries.

The direction of the batteries should match the marks in the

case.

CAUTION

1. Do not use new and old batteries, or different kinds of batteries

together.

2. Take out the batteries when you do not use the remote controller for

2 or 3 months.

CAUTION

MAINTENANCE

Cleaning and maintenance must be carried out only by qualified service personal. Before cleaning,

stop operation and switch off the power supply.

CAUTION

1. AIR FILTER

Please clean the filter once about every two weeks. By doing so, the power rates are saved. In

case the air filter is full of dust, the air flow will decrease and the cooling capacity will be reduced.

Further, noise may occur. Be sure to clean the filter following the procedure below.

PROCEDURE

1

Open the front panel carefully and remove the filter.

2

Vacuum dust from the air filter using vacuum cleaner.

If there is too much dust, wash the filter with a detergent

and rinse it thoroughly. After that, dry it in the shade.

3

Set the filter with “FRONT” mark facing front, and

slot them into the original state.

After attaching the filters, push the front panel at

three arrow portions as shown in figure and close

it.

Do not wash with hot water at more than 40°C. The filter may shrink.

When washing it, shake off moisture completely and dry it in the shade; do not expose it directly

to the sun. The filter may shrink.

Don't operate the unit without filter. Fault may occur if you continue.

CAUTION

2. CLEANING OF FRONT PANEL

Remove the front panel and wash with clean water.

Wash it with a soft sponge.

After using neutral detergent, wash thoroughly with

clean water.

When front panel is not removed, wipe it with a soft

dry cloth. Wipe the remote controller thoroughly with

a soft dry cloth.

Wipe the water thoroughly.

If water remains at indicators or signal receiver of

indoor unit, it causes trouble.

Method of removing the front panel.

Be sure to hold the front panel with both hands to

detach and attach it.

CAUTION

Removing the Front Panel Attaching the Front Panel

Do not splash or direct water to the body of the unit when cleaning it as

this may cause short circuit.

Never use hot water (above 40°C), benzine, gasoline, acid, thinner or a

brush, because they will damage the plastic surface and the coating.

B

E

N

Z

I

N

E

T

H

I

N

E

R

A

C

I

D

Push the end of the right-side arm outward to release

the tab.

Move the left-side arm outward to release the left tab,

and then pull the panel towards you.

Insert the shaft of the left arm along the step on the

unit into the hole.

Securely insert the shaft of the right arm along the

step on the unit into the hole.

Make

sure

that

the

front

panel

is securely attached,

and then close the front panel.

1.

2.

1.

2.

3.

1

2

Push

Arm

INFORMATION

CAPABILITIES

Heating Capability

This room air conditioner utilizes a heat pump system that absorbs

exterior heat and brings it into a room to be heated. As the ambient

temperature gets lower, heating capability will also lower. In such a

situation, the inverter work to increase compressor rpm to keep the

unit’s heating capability from decreasing. If the unit’s heating perfor-

mance is still unsatisfactory, other heating appliances should be used

to augment this unit’s performance.

The air conditioner is designed to heat an entire room so that it may take some time before you feel warm.

Timer operation is recommended for effective preheating ahead of the desired time.

Cooling and Dehumidifying Capabilities

If the heat present in a room exceeds the unit’s cooling capacity (for example, if there are many people in

the room or other heating appliances are used), the preset room temperature may not be reached.

CAUTION

Do not use a stove

or any other

devices in proximity

high temperature

to the indoor unit.

PROHIBITION



REGULAR INSPECTION

PLEASE CHECK THE FOLLOWING POINTS EVERY EITHER HALF YEARLY OR YEARLY. CONTACT

YOUR SALES AGENT SHOULD YOU NEED ANY HELP.

1

2

WARNING

Check to see if the unit’s earth line has been con-

nected correctly.

If the earth line is disconnected or faulty, unit failure or

electric shock hazard may result.

Check to see if the mounting frame has rusted ex-

cessively or if the outdoor unit has tilted or become

unstable.

It could collapse or fall, causing injury.

AFTER SALES SERVICE AND WARRANTY

WHEN ASKING FOR SERVICE, CHECK THE FOLLOWING POINTS.

CONDITION CHECK THE FOLLOWING POINTS

s Do the batteries need replacement?

s Is the polarity of the inserted batteries correct?

s Is the fuse all right?

s Is the voltage extremely high or low?

s Is the circuit breaker “ON”?

s Is the power plug inserted?

s Do you have any power cut?

s Is the air filter blocked with dust?

s Is the set temperature suitable?

s Have horizontal air deflectors been adjusted to their correct

positions according to the operation mode selected?

s Are the air inlets or air outlets of indoor and outdoor units

blocked?

s Is the fan speed “LOW”or “SILENT”?

When it does not operate.

When it does not cool well.

When it does not heat well.

If the remote controller is not

transmitting a signal.

(Remote controller display is

dim or blank.)

The following phenomena do not indicate unit failure.

The unit is preparing to blow warm air. Please wait.

The outdoor unit is defrosting. Please wait.

Refrigerant flow noise in the pipe or valve sound generated when flow rate is

adjusted.

Noise generated when the unit expands or contracts due to temperature changes.

Noise generated with the indoor unit fan’s rpm changing such as operation start

times.

Noise of the motorized valve when the unit is switched on.

During heating, the operation

indicator blinks and air blow stops

Hissing or fizzy sounds

Squeaking noise

Rustling noise

Clicking noise



s

Contact your sales agent immediately if the

following phenomena should occur:

s

The circuit breaker switches off or the fuse blows

frequently.

s

The switch operation is not stable.

s

Foreign matter or water accidentally enters the unit interior.

s

The power cord gets excessively hot or its insulation is torn or stripped.

s

TIMER lamp on the indoor unit display blinks.

As the nature of the failure can be identified by the blinking cycle,

check the blinking cycle before turning off the circuit breaker.

(

)

Notes

s In quiet operation or stopping the running, the following phenomena may

occasionally occur, but they are not abnormal for the operation.

(1) Slight flowing noise of refrigerant in the refrigerating cycle.

(2) Slight rubbing noise from the fan casing which is cooled and then

gradually warmed as operation stops.

s The odor will possibly be emitted from the room air conditioner because

the various odor, emitted by smoke, foodstuffs, cosmetics and so on,

sticks to it. So please clean the air filter and the evaporator regularly to

reduce the odor.

Noise of the ventilation fan sucking in air present in the drain hose and blowing out

dehumidifying water that had accumulated in the condensed water collector. For

details, consult your sales agent.

Operation noise changes due to power variations according to room temperature

changes.

Mist is generated as the air within the room is suddenly cooled by conditioned air.

Water generated during defrosting operation evaporates and steam is emitted.

Caused as the smells and particles of smoke, food, cosmetics, etc. present in room

air become attached the unit and blown off into the room again.

Defrosting is underway (as the heating operation is stopped, the microcomputer

checks frost accumulated in the outdoor unit and instructs the unit to perform

automatic defrosting if necessary).

Shows preheating or defrosting operation is underway.

As the protective circuit or preheat sensor operates when unit operation is stopped

during preheating and then restarted, or when operation mode is switched from cooling

to heating, the lamp continues to blink.

Actual room temperature may deviate slightly from the remote controller's

temperature setting depending on the number of people in the room, indoor or

outdoor conditions.

s Please contact your sales agent immediately if the air conditioner still fails to operate normally after

the above inspections. Inform your agent of the model of your unit, production number, date of

installation. Please also inform him regarding the fault.

Please note:

On switching on the equipment, particularly when the room light is dimmed, a slight brightness

fluctuation may occur. This is of no consequence.

The conditions of the local Power Supply Companies are to be observed.

Does not reach the temperature

setting

Mist emission

Perking noise

Changing operation noise

Steam emitted from the outdoor unit

The outdoor unit continues to operate

even if operation is stopped.

Odors

The OPERATION lamp is blinking.

If the unit still fails to operate

normally after performing the

above inspections, turn the

circuit breaker off and contact

your sales agent immediately.



SPLIT-KLIMAANLAGE

Diese Raumklimaanlage dient nur der gängigen Nutzung durch Endverbraucher.

Sie ist nicht geeignet für den Schutz, die Konservierung oder die Haltbarmachung von Nahrungsmitteln, Tieren,

Pflanzen, Präzisionsmaschinen, Kunstwerken, Medikamenten o. ä.

Bedienungsanleitung Seite 11~20

Lesen Sie diese Bedienungsanleitung vollständig durch,

um eine optimale Geräteleistung und einen langjährigen

störungsfreien Betrieb sicherzustellen.



S/ETÄREGNENNITÄREGNESSUA

L.H

MODELL

Innengerätes

Av

ß

engerät

RAK-18PED/RAC-18WED

RAK-35PED/RAC-35WED

RAK-50PED/RAC-50WED

RAK-25PED/RAC-25WED

RAK-35PEDC/RAC-35WED

RAK-50PEDC/RAC-50WED

RAK-25PEDC/RAC-25WED

RAK-18PED

RAK-25PED

RAK-35PED

RAK-50PED

RAK-25PEDC

RAK-35PEDC

RAK-50PEDC

RAC-18WED

RAC-25WED

RAC-35WED

RAC-50WED

R32

Ŗ Lesen Sie die folgenden Sicherheitshinweise sorgfältig durch, bevor Sie das Gerät in Betrieb nehmen, um eine ordnungsgemäße

Verwendung sicherzustellen.

Ŗ Achten Sie besonders auf mit “

Warnung ” und “ Vorsicht ” gekennzeichnete Hinweise. Wenn mit

³Warnung´gekennzeich-

nete Hinweise nicht strengstens beachtet werden, kann dies schwere oder tödliche Verletzungen zur Folge haben. Wenn mit

³Vorsicht´ gekennzeichnete Hinweise nicht ordnungsgemäß beachtet werden, kann dies schwerwiegende Folgen haben. Bitte

beachten Sie alle Anweisungen genauestens, um die Sicherheit zu gewährleisten.

Ŗ Die Symbole haben folgende Bedeutung: (Die folgende Symbole sind Beispiele.)

VORSICHTSMASSNAHMEN FÜR DIE INSTALLATION

WARNUNG

Ŗ Versuchen Sie nicht, das Gerät selbst zusammenzubauen.

Wenn Sie das Gerät selbst zusammenbauen, kann es zu Wasserlecks, Störungen, Kurz-

schlüssen oder einem Brand kommen.

VERBOT

Ŗ $GCWHVTCIGP5KG+JTGP*¼PFNGTQFGTGKPGPSWCNKſ\KGTVGP6GEJPKMGTOKVFGT+PUVCNNCVKQPFGU)GT¼VU

Wenn Sie das Gerät selbst installieren, kann es zu Wasserlecks, Störungen, Kurzschlüs-

sen oder einem Brand kommen.

Ŗ Schließen Sie das Erdungskabel an.

Verlegen Sie das Erdungskabel nicht in der Nähe von Wasser- oder Gasleitungen, Blitz-

ableitern oder dem Erdungskabel des Telefons. Unsachgemäße Installation des Erdungs-

kabels kann zu Stromschlägen führen.

ERDLEITER AN-

SCHLIESSEN

Ŗ



Verwenden Sie ausschließlich die angegebenen Leitungen für R . Die Verwendung

anderer Leitungen kann Defekte an den Kupferleitungen oder Störungen zur Folge haben.

VORSICHT

Ŗ Es muss ein Trennschalter installiert werden, der für den Montageort geeignet ist.

Ohne Trennschalter besteht Stromschlaggefahr.

VERBOT

Ŗ



Ŗ 5VGNNGP5KGDGKFGT+PUVCNNCVKQPFGU#DƀWUUUEJNCWEJUGKPGPINGKEJO¼²KIGP9CUUGTƀWUUUKEJGT

Ŗ Achten Sie darauf, dass eine einphasige Stromquelle mit 220 V - 230 V verwendet wird.

Die Verwendung anderer Stromquellen kann zur Überhitzung elektrischer Komponenten

und Brandentwicklung führen.

VERBOT

VORSICHTSMASSNAHMEN FÜR DEN TRANSPORT UND FÜR WARTUNGSARBEITEN

WARNUNG

Ŗ

Ŗ Wenden Sie sich an Ihren Händler, um Wartungsarbeiten durchführen zu lassen. Unsachgemäße

Wartungsarbeiten durch den Gerätebesitzer können zu Stromschlägen und einem Brand führen.

Ŗ Wenden Sie sich an Ihren Händler, wenn das Gerät entfernt oder neu installiert werden muss. Wenn

Sie das Gerät selbst unsachgemäß entfernen und neu installieren, kann es zu Stromschlägen oder

einem Brand kommen.

VORSICHTSMASSNAHMEN FÜR DEN BETRIEB

WARNUNG

Ŗ V

ermeiden Sie im Interesse Ihrer Gesundheit direkte Zugluft über einen längeren

Zeitraum.

VERBOT

Ŗ Führen Sie keine Gegenstände wie dünne Bolzen in die Blende des Gebläse- und

Ansaugeinheit ein, da dies den Hochgeschwindigkeitsventilator im Innern beschä-

digen kann.

Ŗ Verwenden Sie keinen Leiter als Sicherungsdraht, da dies zu einem tödlichen Unfall

führen könnte.

VERBOT

Ŗ Trennen Sie das Gerät während eines Gewitters von der Stromversorgung und

schalten Sie den Trennschalter aus.

Ŗ Sprühdosen und andere brennbare Materialien dürfen nicht in einem Abstand von weniger als

1 Meter von den Luftauslässen der Innen- und Außengeräte abgestellt werden.

Die Erhöhung des Innendrucks einer Sprühdose durch heiße Luft kann zu Rissen und Beschä-

digungen führen.

VERBOT

SICHERHEITSHINWEISE

“AUS”

Bitte bewahren Sie diese Anleitung sorgfältig auf.

Stellen Sie sicher, dass ein Erdungskabel angeschlossen ist.

Das abgebildete Symbol weist auf ein Verbot hin.

Dieses Symbol weist darauf hin, dass die Anweisungen

beachtet werden müssen.

Ŗ



Das Außengerät kann in Brand geraten, wenn entzündbare Gase in

seiner Nähe entweichen.



Bei ungewöhnlichen Vorkommnissen (wie Brandgeruch) nehmen Sie das Gerät

außer Betrieb und schalten den Trennschalter aus. Wenden Sie sich an Ihren

Händler. Wenn Sie das Gerät bei ungewöhnlichen Vorkommnissen weiter

betreiben, kann es zu Störungen, Kurzschlüssen oder einem Brand kommen.



32

eses Gerät ist mit R32 gefülltDi

Verwenden Sie während der Installation, dem

Transport oder der Reparatur nur das auf dem

Außengerät angegebene Kältemittel (R32).

Wenn Sie andere Kältemittel verwenden, kann

dies zu Störungen oder Schäden an der Einheit

und zu Körperverletzungen führen.

Ŗ

VORSICHT

•

VERBOT

NICHT BEFEUCHTEN

• Versuchen Sie nicht, das Gerät mit nassen Händen zu bedienen – es besteht

Lebensgefahr.

• Wenn Sie das Gerät bei gleichzeitigem Gebrauch von Brennstoffen be-

treiben, lüften Sie den Raum regelmäßig, um eine ausreichende Sauer-

stoffzufuhr zu gewährleisten.

SICHERHEITS-

VOR

KEHRUNGEN

SIND STRIKT ZU

BEFOLGEN

VERBOT

• Richten Sie die kalte Luftströmung aus der Luftaustrittsblende nicht direkt

auf Geräte zum Heizen und zur Warmwasserbereitung (z. B. Wasserkocher,

Ofen), da sie dadurch in ihrer Funktion beeinträchtigt werden können.

• Überprüfen Sie regelmäßig, dass der Anbaurahmen für das Außengerät

sicher befestigt und nicht beschädigt ist. Andernfalls könnte das Außen-

gerät herunterfallen

und eine Gefahr darstellen.

VERBOT

• Reinigen Sie das Gerät nicht mit Wasser oder stellen Sie keinen Wasserbehäl-

ter wie eine Vase auf das Innengerät.

Dies birgt das Risiko von Stromschlägen.

•

VERBOT

• Schalten Sie beim Reinigen das Gerät mit der Fernbedienung und den Trenn-

schalter aus, da der Hochgeschwindigkeitslüfter im Gerät ein Verletzungsrisiko

darstellt.

• Schalten Sie den Trennschalter aus, wenn das Gerät für einen längeren Zeitraum

nicht verwendet wird.

VERBOT

• Stellen Sie sich nicht auf das Außengerät und stellen Sie keine Gegenstände darauf

ab.

•

VERBOT

• Wenn die Temperatur im Raum die Kühl- bzw. Heizleistung des Geräts übersteigt

(z. B. wenn sich mehrere Personen im Raum aufhalten, zusätzliche Heizgeräte

verwendet werden usw.), kann die voreingestellte Raumtemperatur nicht erreicht

werden.

•

VERBOT

NICHT BERÜHREN

•

• Berühren Sie nicht die Kühlleitung und das Verbindungsventil.

Es besteht Verbrennungsgefahr.

NICHT BERÜHREN

•

VORSICHTSMASSNAHMEN FÜR DEN BETRIEB

“AUS”

Dieses Gerät darf nicht von Kindern oder Personen mit verminderten physischen, sensorischen oder mentalen

Fähigkeiten oder fehlenden Erfahrungen und Kenntnissen v erwendet werden, es sei denn, sie werden dabei

beaufsichtigt oder instruiert. Kinder müssen beaufsichtigt w erden, damit sie nicht mit dem Gerät spielen.

Das Produkt muss entsprechend der Herstellerspezifikation bedient werden und ist

für keine sonstigen Verwendungszwecke vorgesehen.

Stellen Sie keine Pflanzen direkt unter den Luftstrom, da die Zugluft den Pflanzen

schadet.

Wenn das Gerät bei geöffneten Türen und/oder Fenstern betrieben wird (bei einer

Luftfeuchtigkeit im Raum von über 80 %) und der Luftdeflektor

für eine längere Zeit

nach unten weist oder sich automatisch bewegt, kondensiert Wasser am Luftdeflektor

und tropft gelegentlich herunter. Damit Ihre Einrichtung nicht feucht wird, vermeiden

Sie derartige Betriebsbedingungen über einen längeren Zeitraum.

Die Reinigung des Innengeräts darf nur von autorisiertem Personal durchgeführt werden.

Bitte wenden Sie sich an Ihren Vertriebspartner.

Die Verwendung eines handelsüblichen Reinigungsmittels oder dergleichen kann die

Kunststoffteile beschädigen oder die Abflussleitung verstopfen, was zu Tropfwasserbildung

mit der Gefahr von Stromschlägen führt.

Die Ansaugöffnung, die untere Oberfläche oder den Aluminiumgrat des Außengeräts

nicht berühren.

Es besteht Verletzungsgefahr .



BEZEICHNUNGEN UND FUNKTIONEN DER EINZELNEN TEILE

INNENGERÄT

BETRIEBSBEREICH

Betriebsart Kühl-/Entfeuchterbetrieb Heizbetrieb

Außentemperatur -10 bis 43 °C-15 bis 21 °C

Luftfilter

Verhindert das Eindringen von Staub in das Innengerät.

(Siehe Seite 16)

Frontblende

(Siehe Seite 17)

Anzeigen des Innengeräts

Leuchten, die die Betriebsbedingungen anzeigen.

(Siehe Seite 15)

Horizontaler Deflektor / Vertikaler Deflektor

(Luftauslass)

Fernbedienung

Sendet ein Betriebssignal an das Innengerät zur Steuerung

des gesamten Geräts.

BEZEICHNUNG UND ABMESSUNGEN DES MODELLS

MODELL BREITE (mm) HÖHE (mm) TIEFE (mm)



780 280 21

27

792 600 299

660 530 8

Info zum Außengerät:

•

Wenn während des Betriebs des Innengeräts

„STOP“ gewählt wird, dreht sich das Gebläse

des Außengeräts noch 10 bis 60 Sekunden

weiter, um die elektrischen Komponenten zu

kühlen.

Während des Heizbetriebs bildet sich Konden-

satwasser aufgrund des Entfrostungsvorgangs.

Verdecken Sie nicht die Abflussöffnung des

Außengeräts, da das Wasser ansonsten in

kalten Umgebungen

gefrieren könnte.

Wenn das Außengerät an der Decke angebracht

ist, installieren Sie einen Stopfen und ein

Abflussrohr an der Abflussöffnung, um das

Wasser abzuführen.

AUSSENGERÄT

Luftauslass

Gibt im Heizungsbetrieb kalte

Drain hose

Drains the dehumidified water from the indoor unit to the

outdoor during “cooling” or “dehumidifying” operation.

Piping and Wiring

Air inlets (Rear and left sides)

Drain hose

Drains the dehumidified water from the indoor unit to the

outdoor during “cooling” or “dehumidifying” operation.

Piping and Wiring

Air inlets (Rear and left sides)

Luft und im

Kühl- oder

Entfeuchterbetrieb warme

Luft ab.

Luftauslass

Gibt im Heizungsbetrieb kalte

Luft und im

Kühl- oder

Entfeuchterbetrieb warme

Luft ab.

RAC-18WED

RAC-25WED

RAC-35WED

RAC-50WED

RAK-18/25/35/50PED,RAK-25/35/50PE

RAC-18/25/35WED

DC

5

La page charge ...

Hitachi RAK-25PED Manuel utilisateur

Ce manuel convient également à

Hitachi RAK-25PED Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents