Enterasys SmartSTACK EPIM1000-S1SX 1000BASE SX-SC Quick Installation Manual

Marque: Enterasys

Modèle: SmartSTACK EPIM1000-S1SX 1000BASE SX-SC

Catégorie: Commutateurs réseau

Taper: Quick Installation Manual

SMARTSTACK FAST ETHERNET SWITCH

1000BASE SX-SC GIGABIT ETHERNET

EXPANSION MODULE

Cabletron’s EPIM1000-S1SX 1000Base SX-SC

Gigabit Ethernet Expansion Module provides a short-

wavelength (850 nm) Gigabit port that can be used for

a high-speed backbone or server connections. It

contains one 1000Base-SX port that can be connected

to a site up to 550 m (1805 ft) away with fiber cable.

Gigabit Port LEDs

Port LEDs are provided for the module on the front

panel of the switch. These LEDs provide port status for

“at-a-glance” network monitoring. The following table

details the indicator functions provided by the ELS100-

S24TX2M:

sDELeludoMnoisnapxE

sDEL noitidnoC sutatS

kniLnOnodehsilbatseneebsahknildilavA

.tropeht

gnihsalFro,delbasidyllaunamneebsahtroP

oteudmetsysehtybdenoititrap

.srorreevissecxe

sutatSnO.tolssihtnidellatsnisieludomA

ytivitcAgnihsalF.tropehthguorhtgnissapsiciffarT

INSTALLING THE MODULE

CAUTION: The EPIM1000-S1SX module is designed

for the ELS100-S24TX2M switch only. Do not try to

install this module in any other units.

The EPIM1000-S1SX Expansion Module installs in

either of the two lower slots on the rear panel of the

ELS100-S24TX2M switch. Do not install this module in

the switch’s upper slot. To install the module, follow the

instructions below.

Equipment Checklist

After unpacking the EPIM1000-S1SX Expansion

Module, check the contents of the box to be sure you’ve

received the following items:

• One EPIM1000-S1SX Expansion Module

• This document

Handling the Module

CAUTION: The EPIM1000-S1SX Expansion Module

can easily be damaged by electrostatic discharge.

To prevent electrostatic damage, observe the following

guidelines:

• Do not remove the module from its packaging until

you are ready to install it.

• Do not touch any of the module’s pins, connectors

or components.

• Hold the module only by its edges or front panel.

• Wear an anti-static wristband connected to a

suitable earth ground whenever handling the

module.

• Store or transport this module only in appropriate

anti-static packaging.

Instructions

CAUTION: The switch must be powered off before

installing or replacing any module.

1. Power off the switch: Disconnect the AC power

cord from the switch. If a redundant power unit

(RPU) is present, disconnect its DC cable

connection to the switch.

2. Remove network cables: If you are replacing a

module, remove the cable attached to the port on

the module.

3. Loosen the screws on the installed module or

slot faceplate: Using your fingers or a flathead

screwdriver, turn the screws securing the module

(or faceplate on the slot) in a counter-clockwise

direction until they are free of the chassis. Be sure

not to completely remove the screws from the

module or faceplate.

4. Remove the installed module or faceplate:

Firmly pull on the screws until the module is free of

the switch. Carefully slide the module straight out

of the slot.

Keep the original faceplate for future use. If you

should remove the module, replace the faceplate to

prevent dust and debris from entering the unit and

to maintain proper air flow.

5. Insert the new module into the switch: Holding

the new module with the text on the front panel

upright, carefully slide the module into the switch

slot and press gently until it snaps into place. Be

sure the new module’s front panel is flush with the

switch panel.

6. Secure the new module: Secure the new module

in place by screwing the attached screws clockwise

into the switch’s chassis. Tighten them enough to

secure the module, but not so tight as to prevent

them from being unscrewed by hand.

7. Connect the network cable: Connect fiber cable

to the port on the newly installed module. See

“Connectivity Guidelines” in this guide for further

information.

8. Power on the switch: Reconnect the previously

removed power sources to the switch. The switch’s

front-panel LEDs should indicate the status of the

new connection. Check the LED indicators for the

fiber port to ensure that they are operating

correctly. Refer to the table of LEDs in this guide

for a description of the LED indications. If the

module does not respond, see “Troubleshooting”

below.

More details concerning connection options and

network applications can be found in the

ELS100-S24TX2M Installation Guide. Information on

the module’s configuration options can be found in the

Management Guide that is included with the base unit.

TROUBLESHOOTING

If you experience any problems with the module, check

the following items before contacting Cabletron’s

Technical Support:

• Ensure the ELS100-S24TX2M switch with the

Gigabit Expansion Module is powered up.

• Ensure that the device attached to the module is

powered up and operating correctly.

• Ensure that the module is properly seated in the

slot.

• Verify that the attached device is configured to

match the communication mode used by the

module (1 Gbps, and half or full duplex).

• Check the connectors on both ends of the cable to

be sure they are properly engaged. When attaching

fiber cable to an SC-type port, be sure the plug

clicks into place to ensure that it is properly seated.

• Be sure the fiber terminators are clean. You can

clean the cable plugs by wiping them gently with a

clean tissue or cotton ball moistened with a little

ethanol. Dirty fiber terminators on fiber optic cables

will impair the quality of the light transmitted through

the cable.

SAFETY WARNING

Before installing or removing the EPIM1000-S1SX, first disconnect the

switch from the main power supply. For full safety instructions, please refer

to the user guide that accompanies the switch.

Warning:

Optical Safety for

Fiber Optic Modules

When using a fiber optic media expansion module, never look at the

transmit laser while it is powered on. Also, never look directly at the fiber

TX port and fiber cable ends when they are powered on.

Avertissment:

Ports pour fibres optiques -

sécurité sur le plan optique

Ne regardez jamais le laser tant qu'il est sous tension.

Ne regardez jamais directement le port TX (Transmission) à fibres optiques

et les embouts de câbles à fibres optiques tant qu'ils sont sous tension.

Warnhinweis:

Faseroptikanschlüsse -

Optische Sicherheit

Niemals ein Übertragungslaser betrachten, während dieses eingeschaltet ist.

Niemals direkt auf den Faser-TX-Anschluß und auf die Faserkabelenden

schauen, während diese eingeschaltet sind.

SPECIFICATIONS

Ports

1 1000Base-SX

Communication Mode

Half or full duplex,

auto-negotiation for duplex mode and flow control

Network Interface

SC connector, 850 nm short-wavelength transceiver

62.5/125 or 50/125 micron multimode fiber cable

Switch Method

Store-and-forward

Queue Buffer

2 Mbytes

Size

4.82 x 3.57 x 1.08 in.

(12.25 x 90.70.5 x 2.74 cm)

Power Consumption

2.4W maximum

Temperature

Operating: 32° to 122° F (0° to 50° C)

Storage: -40° to 158° F (-40° to 70° C)

Humidity

Operating: 5% to 95%

Compliances

CE Mark

Emissions

FCC Class A

EN55022 (CISPR 22) Class A

VCCI Class A

C-Tick

Immunity

IEC 1000-4-2/3/4/6

Standards

802.3z Gigabit Ethernet

ISO/IEC 8802-3

CONNECTIVITY GUIDELINES

snoitacificepSdnasepyTelbaC

elbaCepyThtgneL.xaMrotcennoC

T-esaB01PTUmho-0015,4,3.taC).tf823(m00154-JR

XT-esaB001PTUmho-0015.taC).tf823(m00154-JR

XF-esaB001norcim521/5.26ro521/05

rebifedomitlumeroc

xelpudflaH).tf4.153,1(m214TSroCS

xelpudlluF)selim42.1(mk2TSroCS

rebifedom-elgnis521/01)tf404,61(mk5TSroCS

XS-esaB0001norcim521/5.26ro521/05

rebifedomitlumeroc

gniwollofehteeS

elbat

TSroCS

XL-esaB0001FMSroFMMgniwollofehteeS

elbat

TSroCS

snoitacificepSrebiFXS-esaB0001

retemaiDrebiF htdiwdnaBladoM egnaR

norcim521/5.26

mk/zHM061)m022-2(tf227-7

mk/zHM002)m572-2(tf209-7

norcim521/05

mk/zHM004)m005-2(tf1461-7

mk/zHM005)m055-2(tf5081-7

snoitacificepSrebiFXL-esaB0001

retemaiDrebiF htdiwdnaBladoM egnaR

FMM521/5.26

mk/zHM005)tf5081-7(m055-2

FMM521/05

mk/zHM004)tf5081-7(m055-2

mk/zHM005)tf5081-7(m055-2

FMS521/01A/N)tf404,61-7(mk5-m2

retemaiDkrowteNtenrehtEtsaFmumixaM

epyTretaepeR

rebmuNdna

riaPdetsiwT

XT-ESAB001

rebiF/riaPdetsiwT

XFdnaXT-ESAB001

IssalC1)tf656(m002)tf4.558(m8.062

IIssalC1)tf656(m002)tf6.2101(m8.803

IIssalC2)tf4.276(m502)tf1.907(m2.612

Note: Network diameter is defined as the wire distance between

two end stations in the same collision domain.

EPIM1000-S1SX

1000BASE SX-SC

GIGABIT ETHERNET

EXPANSION MODULE

QUICK INSTALLATION GUIDE

9033266

E1099-R01

150180-102

NOTICE

Cabletron Systems reserves the right to make changes in specifications and other

information contained in this document without prior notice. The reader should in

all cases consult Cabletron Systems to determine whether any such changes have

been made.

The hardware, firmware, or software described in this manual is subject to change

without notice.

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY

INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES

WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS)

ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION

CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN ADVISED

OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH

DAMAGES.

 1999 by Cabletron Systems, Inc., P.O. Box 5005, Rochester, NH 03866-5005

Printed in Taiwan, R.O.C.

Order Number:9033266 October 1999

Cabletron, Cabletron Systems, and SmartSTACK are trademarks or registered

trademarks of Cabletron Systems, Inc.

Microsoft, Windows, Windows 95, Windows 98, and Windows NT are either

trademarks or registered trademarks of Microsoft Corporation.

Netscape and Netscape Navigator are trademarks of Netscape Communications

Corporation.

All other product names mentioned in this manual may be trademarks or registered

trademarks of their respective companies.

FCC NOTICE

This device complies with Part 15 of the FCC rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

NOTE:This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC rules. These limits are

designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment uses,

generates, and can radiate radio frequency energy and if not installed in accordance

with the operator’s manual, may cause harmful interference to radio communica-

tions. Operation of this equipment in a residential area is likely to cause interfer-

ence in which case the user will be required to correct the interference at his own

expense.

WARNING:Changes or modifications made to this device which are not expressly

approved by the party responsible for compliance could void the user’s authority to

operate the equipment.

INDUSTRY CANADA NOTICE

This digital apparatus does not exceed the Class A limits for radio noise emissions

from digital apparatus set out in the Radio Interference Regulations of the Canadian

Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les

limites applicables aux appareils numériques de la class A prescrites dans le

Règlement sur le brouillage radioélectrique édicté par le ministère des Communica-

tions du Canada.

VCCI NOTICE

EC CONFORMANCE DECLARATION

European contact: Cabletron Systems Limited

Nexus House, Newbury Business Park

London Road, Newbury

Berkshire RG13 2PZ, England

This information technology product complies with ISO/IEC Guide 22 and

EN45014. It conforms to the following specifications:

EN55022(1988)/CISPR-22(1985) Class A

EN50082-1: IEC 1000-4-2, 3, 4, 6

This information technology product complies with the requirements of

the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/

EEC and carries the CE Mark accordingly.

Only qualified personnel should perform installation

procedures.

Enterasys SmartSTACK EPIM1000-S1SX 1000BASE SX-SC Quick Installation Manual

Marque: Enterasys

Modèle: SmartSTACK EPIM1000-S1SX 1000BASE SX-SC

Catégorie: Commutateurs réseau

Taper: Quick Installation Manual

Télécharger le PDF

rapport

dans d''autres langues

English: Enterasys SmartSTACK EPIM1000-S1SX 1000BASE SX-SC

Enterasys SmartSTACK EPIM1000-S1SX 1000BASE SX-SC Quick Installation Manual

Enterasys SmartSTACK EPIM1000-S1SX 1000BASE SX-SC Quick Installation Manual

dans d''autres langues

Autres documents