Cabletron Systems DLM6C-AA Overview And Setup Manual

DIGITAL MultiSwitch 700

DLM6C-AA

Overview and Setup Guide

DIGITAL MultiSwitch 700

DLM6C-AA

Overview and Setup Guide

Part Number: 9032610

September1998

This guide describes how to install and configure the DIGITAL MultiSwitch

700 DLM6C-AA chassis.

Revision/Update Information: This is a new document.

Cabletron Systems reserves the right to make changes in specifications and other information

contained in this document without prior notice. The reader should in all cases consult Cabletron

Systems to determine whether any such changes have been made.

The hardware, firmware, or software described in this manual is subject to change without notice.

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL,

INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT

NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR

THE INFORMATION CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN

ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH

DAMAGES.

Printed in the United States of America

SPECTRUM and LANVIEW are registered trademarks of Cabletron Systems, Inc.

DIGITAL and the DIGITAL logo are trademarks of Digital Equipment Corporation.

All other product names mentioned in this manual may be trademarks or registered trademarks of

their respective companies.United States Government Restricted RightsUnited States Government

Restricted Rights

The enclosed product (a) was developed solely at private expense; (b) contains “restricted computer

software” submitted with restricted rights in accordance with Section 52227-19 (a) through (d) of the

Commercial Computer Software - Restricted Rights Clause and its successors, and (c) in all respects

is proprietary data belonging to Cabletron and/or its suppliers.

UNITED STATES GOVERNMENT RESTRICTED RIGHTS

The enclosed product (a) was developed solely at private expense; (b) contains “restricted computer

software” submitted with restricted rights in accordance with Section 52227-19 (a) through (d) of the

Commercial Computer Software - Restricted Rights Clause and its successors, and (c) in all respects

is proprietary data belonging to Cabletron and/or its suppliers.

For Department of Defense units, the product is licensed with “Restricted Rights” as defined in the

DoD Supplement to the Federal Acquisition Regulations, Section 52.227-7013 (c) (1) (ii) and its

successors, and use, duplication, disclosure by the Government is subject to restrictions as set forth in

subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at

252.227-7013. Cabletron Systems, Inc., 35 Industrial Way, Rochester, New Hampshire 03867-0505.

FCC Notice — Class A Computing Device:

This equipment generates, uses, and may emit radio frequency energy. The equipment has been type

tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC

rules, which are designed to provide reasonable protection against such radio frequency interference.

Operation of this equipment in a residential area may cause interference in which case the user at his

own expense will be required to take whatever measures may be required to correct the interference.

Any modifications to this device - unless expressly approved by the manufacturer - can void the user's

authority to operate this equipment under part 15 of the FCC rules.

DOC Notice — Class A Computing Device:

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital

apparatus set out in the Radio Interference Regulations of the Canadian Department of

Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables

aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique

édicté par le ministère des Communications du Canada.

VCCI Notice — Class A Computing Device:

Taiwanese Notice — Class A Computing Device:

CE Notice — Class A Computing Device:

Warning!

This is a Class A product. In a domestic environment, this product may cause radio interference, in

which case the user may be required to take adequate measures.

Achtung!

Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses

Gerätes Rundfunkstörungen auftreten, in welchen Fällen der Benutzer für entsprechende

Gegenma

ßnahmen verantwortlich ist.

Avertissement!

Cet appareil est un appareil de Classe A. Dans un environnement résidentiel cet appareil peut

provoquer des brouillages radioélectriques. Dans ce cas, il peut être demandé à l'utilisateur de prendre

les mesures appropriées.

CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT

IMPORTANT: Before utilizing this product, carefully read this License Agreement.

This document is an agreement between you, the end user, and Cabletron Systems, Inc. (“Cabletron”)

that sets forth your rights and obligations with respect to the Cabletron software program (the

“Program”) contained in this package. The Program may be contained in firmware, chips or other

media. BY UTILIZING THE ENCLOSED PRODUCT, YOU ARE AGREEING TO BECOME

BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE LICENSE AND

THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF YOU DO NOT

AGREE TO THE TERMS OF THIS AGREEMENT, PROMPTLY RETURN THE UNUSED

PRODUCT TO THE PLACE OF PURCHASE FOR A FULL REFUND.

CABLETRON SOFTWARE PROGRAM LICENSE

1. LICENSE. You have the right to use only the one (1) copy of the Program provided in this

package subject to the terms and conditions of this License Agreement.

You may not copy, reproduce or transmit any part of the Program except as permitted by the

Copyright Act of the United States or as authorized in writing by Cabletron.

2. OTHER RESTRICTIONS

. You may not reverse engineer, decompile, or disassemble the

Program.

3. APPLICABLE LAW

. This License Agreement shall be interpreted and governed under the laws

and in the state and federal courts of New Hampshire. You accept the personal jurisdiction and

venue of the New Hampshire courts.

EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY

1. EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in

writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including

its documentation and media).

CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO

YOU BY CABLETRON IN WRITING, EITHER EXPRESSED OR IMPLIED, INCLUDING

BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE

ACCOMPANYING WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.

2. NO LIABILITY FOR CONSEQUENTIAL DAMAGES

. IN NO EVENT SHALL

CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER

(INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS,

PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL,

INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS)

ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT,

EVEN IF CABLETRON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH

DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR

LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR

ON THE DURATION OR LIMITATION OF IMPLIED WARRANTIES, IN SOME

INSTANCES THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO

YOU.

DECLARATION OF CONFORMITY

Application of Council Directive(s): 89/336/EEC

73/23/EEC

Manufacturer’s Name: Cabletron Systems, Inc.

Manufacturer’s Address: 35 Industrial Way

PO Box 5005

Rochester, NH 03867

European Representative Name: Mr. J. Solari

European Representative Address: Cabletron Systems Limited

Nexus House, Newbury Business Park

London Road, Newbury

Berkshire RG13 2PZ, England

Conformance to Directive(s)/Product Standards: EC Directive 89/336/EEC

EC Directive 73/23/EEC

EN 55022

EN 50082-1

EN 60950

Equipment Type/Environment: Networking Equipment, for use in a

Commercial or Light Industrial

Environment.

We the undersigned, hereby declare, under our sole responsibility, that the equipment packaged

with this notice conforms to the above directives.

Manufacturer Legal Representative in Europe

Mr. Ronald Fotino Mr. J. Solari

___________________________________ ___________________________________

Full Name Full Name

Principal Compliance Engineer Managing Director - E.M.E.A.

___________________________________ ___________________________________

Title Title

Rochester, NH, USA Newbury, Berkshire, England

___________________________________ ___________________________________

Location Location

DLM6C-AA Overview and Setup Guide ix

CONTENTS

PREFACE

Using This Guide............................................................................xi

Structure of This Guide...................................................................xi

Document Conventions.................................................................xii

Using the DIGITAL MultiSwitch 700 Manual Set...........................xii

Correspondence...........................................................................xiii

Documentation Comments..............................................xiii

World Wide Web..............................................................xiii

Getting Help..................................................................................xiii

SAFETY

Overview........................................................................................xv

Safety Requirements....................................................................xvi

CHAPTER 1 INTRODUCTION

1.1 Overview......................................................................................1-1

1.2 Features ......................................................................................1-2

CHAPTER 2 INSTALLATION REQUIREMENTS AND

SPECIFICATIONS

2.1 Site Guidelines ............................................................................2-1

2.2 Configuration Guidelines.............................................................2-2

2.3 Operating Specifications..............................................................2-2

2.3.1 Physical Specifications ...................................................2-3

2.3.2 Power Supply Requirements ..........................................2-4

2.4 LEDs............................................................................................2-4

2.4.1 Power Supply LEDs........................................................2-4

2.4.2 Fan Tray LED..................................................................2-6

CHAPTER 3 DLM6C-AA SETUP

3.1 Unpacking the DLM6C-AA ..........................................................3-1

3.2 Setting Up the DLM6C-AA...........................................................3-2

3.2.1 Installation Order.............................................................3-2

3.2.2 Installing the Cable Management Bar.............................3-3

3.2.3 Rack Mounting the DLM6C-AA.......................................3-4

3.2.4 Attaching the ESD Wrist Strap........................................3-5

3.2.5 Installing a Power Supply Module...................................3-6

3.2.6 Installing DLM6C-AA Interface Modules.........................3-9

Contents

x DLM6C-AA Overview and Setup Guide

3.3 Powering Up a DLM6C-AA with an AC Power Supply...............3-11

3.4 Powering Up a DLM6C-AA with a DC Power Supply.................3-11

3.4.1 Connecting an HA205-MD to 48/60 Vdc Source...........3-13

3.5 Removing and Reinstalling the Fan Tray...................................3-14

3.5.1 Removing the Fan Tray.................................................3-14

3.5.2 Reinstalling the Fan Tray ..............................................3-15

DLM6C-AA Overview and Setup Guide xi

PREFACE

Welcome to the DIGITAL MultiSwitch 700 DLM6C-AA Overview and Setup

Guide

. This guide explains how to set up and configure the DLM6C-AA

chassis.

USING THIS GUIDE

Read through this guide completely to familiarize yourself with its

contents and to gain an understanding of the features and capabilities of

the DLM6C-AA chassis. This guide lists the features and options of the

chassis, explains how to remove and reinstall the fan tray, and explains

how to install the power supplies, modules, and the cable management

bar. A general working knowledge of data communications networks is

helpful when setting up the DLM6C-AA chassis.

STRUCTURE OF THIS GUIDE

This guide is organized as follows:

Chapter 1, Introduction, discusses the features and capabilities of the

DLM6C-AA.

Chapter 2, Installation Requirements and Specifications, lists the

location requirements that must be met before installing the DLM6C-AA

in a cabinet or rack. This chapter also includes some configuration

guidelines, environmental guidelines, and operating specifications for the

DLM6C-AA and related power supply modules.

Chapter 3, DLM6C-AA Setup, contains instructions for rack mounting

the DLM6C-AA, removing and reinstalling the fan tray, installing the

power supplies, modules, and cable management bar, and powering up the

DLM6C-AA.

In this document, the DIGITAL MultiSwitch 700 DLM6C-AA

chassis is referred to as either the “DLM6C-AA” or the

“chassis.”

xii DLM6C-AA Overview and Setup Guide

DOCUMENT CONVENTIONS

Throughout this guide, the following symbols are used to call attention to

important information.

USING THE DIGITAL MULTISWITCH 700 MANUAL SET

Other manuals have been developed for the interface modules that can be

installed in the DLM6C-AA chassis. These manuals explain how to

install the modules into the DLM6C-AA chassis, how to attach cable

segments to the modules, and how to configure the modules using Local

Management after installation is complete. Specifications for all modules

are included in each manual.

Each manual in this set assumes that the qualified personnel installing the

module has a general working knowledge of data communications

networks and their physical layer components.

Note symbol. Calls the reader’s attention to any item of

information that may be of special importance.

!

Caution symbol. Contains information essential to avoid

damage to the equipment.

Electrical Hazard Warning symbol. Warns against an action

that could result in the personal injury or death due to an

electrical hazard.

DLM6C-AA Overview and Setup Guide xiii

CORRESPONDENCE

Documentation Comments

If you have comments or suggestions about this manual, send them to

DIGITAL Network Products:

World Wide Web

To locate product-specific information, refer to the DIGITAL Network

products Home Page on the World Wide Web at the following locations:

GETTING HELP

Contact your DIGITAL representative for technical support. Before

calling, have the following information ready:

• A description of the failure

• A description of any action(s) already taken to resolve the problem

(e.g., changing mode switches, rebooting the unit, etc.)

• A description of your network environment (layout, cable type, etc.)

• Network load and frame size at the time of trouble (if known)

• The device history (i.e., have you returned the device before, is this a

recurring problem, etc.)

Attn.: Documentation Project Manager

E-MAIL: doc_quality@lkg.mts.dec.com

North America: http://www.networks.digital.com

Europe: http://www.networks.europe.digital.com

Asia Pacific: http://www.networks.digital.com.au

DLM6C-AA Overview and Setup Guide xv

SAFETY

OVERVIEW

Any warning or caution that appears in this manual is defined as follows:

WARNING Warns against an action that could result in

equipment damage, personal injury, or

death.

VORSICHT Warnt den Benutzer vor Aktionen, die das

Gerät beschädigen, Personen verletzen

oder sogar zum Tot führen könnten.

DANGER Déconseille à l'utilisateur d'exécuter une

action pouvant entraîner des dommages

matériels, corporels voire même la mort.

AVISO Previene contra una acción que podría

dañar el equipo, provocar daños personales

o la muerte.

CAUTION Contains information essential to avoid dam-

age to the equipment.

ACHTUNG Liefert wichtige Informationen, um einen

Geräteschaden zu vermeiden.

ATTENTION Informations indispensables permettant

d'éviter les dommages matériels.

PRECAUCIÓN Contiene información esencial para evitar

daños al equipo.

!

Safety

xvi DLM6C-AA Overview and Setup Guide

SAFETY REQUIREMENTS

The warnings or cautions that must be observed for the hardware

described in this manual are listed below in English, German, French, and

Spanish.

WARNING Only qualified personnel should install or

service this unit.

VORSICHT Diese Einheit darf nur von qualifizierten Fach-

leuten installiert oder gewartet werden.

DANGER L’installation et la maintenance de cet appar-

eil sont réservées à un personnel qualifié.

AVISO Sólo el personal cualificado debe instalar o

dar mantenimiento a esta unidad.

WARNING If theDLM6C-AA is to be placed on a shelving

unit, the shelf must be able to support 75

pounds.

If the DLM6C-AA is to be rack mounted, care

must be taken to ensure that the rack used will

support the unit and that the rack remains

stable with the DLM6C-AA installed.

If the rack is not secured to the floor, it is

recommended that the chassis be installed in

the bottom half of the rack. This prevents the

rack from being top heavy.

Two people may be required to lift the chassis

into place.

Safety Requirements

DLM6C-AA Overview and Setup Guide xvii

VORSICHT Wenn der DLM6C-AA auf einem Regal plaziert

werden soll, muß das Regal eine Last von ca.

34 Kilogramm (75 Pfund) unterstützen können.

Wenn der DLM6C-AA dagegen in einem

Einschubgehäuse installiert werden soll, muß

der Einschub die Einheit stützen können und

nach der Installation des DLM6C-AA stabil

bleiben. Wenn das Einschubgehäuse nicht am

Boden befestigt ist, wird die Installation im

unteren Teil des Gehäuses empfohlen, da

andernfalls der obere Teil zu schwer und nicht

stabil sein könnte. Eventuell sind zwei

Personen zum Einsetzen in das Gehäuse

erforderlich.

DANGER Si l'appareil DLM6C-AA doit être monté sur un

support, celui-ci doit pouvoir accepter un poids

de 34 kg. Si l'appareil doit être monté sur un

rack, assurez-vous que celui-ci est prévu pour

cela et qu'il restera stable une fois l'appareil

installé. Si le rack n'est pas fixé au sol, il est

recommandé d'installer le châssis dans la

partie inférieure du rack, pour ne pas

surcharger la partie supérieure. Prévoir deux

personnes pour insérer le châssis.

AVISO Si el DLM6C-AA se va a colocar en una unidad

de estantes, el estante deberá ser capaz de

aguantar 34 kg. Si el DLM6C-AA se va a

montar en bastidor, es preciso asegurarse de

que el bastidor tenga capacidad para aguantar

la unidad y de que permanecerá estable una

vez instalado el DLM6C-AA. Si el bastidor no

está fijado al suelo, se recomienda instalar el

chasis en la mitad inferior del bastidor, para

evitar que la parte superior del mismo se

venza por exceso de peso. Es conveniente

pedir la ayuda de otra persona para colocar el

chasis en su lugar.

Safety

xviii DLM6C-AA Overview and Setup Guide

WARNING To reduce the risk of electric shock or energy

hazards:

Ensure the branch circuit overcurrent

protection is rated at a minimum of 25 A.

Use the 10 AWG solid copper conductors only.

Ensure that a readily accessible disconnect

device that is suitably approved and rated, is

incorporated in the field wiring.

To be installed in a restricted access area in

accordance with the NEC or the authority

having jurisdiction.

VORSICHT Um Elektroschock und Stromgefahr zu

vermeiden: Stellen Sie sicher, daß die

Überstromschutzeinrichtung des

Verzweigungsstromkreises auf mindestens 25

A eingestellt ist. Verwenden Sie nur 10

AWG-Kupferhalbleiter. Ein genehmigtes, leicht

zugängliches Trenngerät mit angemessener

Strom- und Spannungsleistung muß in der

Feldverkabelung integriert sein. Die Installation

darf nur in einem Gebiet mit begrenztem Zutritt

entsprechend dem NEC oder der zuständigen

rechtlichen Behörde erfolgen.

DANGER Pour réduire les risques de choc électrique et

de tout danger afférent : assurez-vous que la

protection du circuit accepte au minimum 25 A.

N'utilisez que des conducteurs en cuivre type

10 AWG. Vérifiez qu'un appareil de

déconnexion adapté et facilement accessible

soit installé sur la câblage. L'installation doit

être faite conformément aux réglements en

vigueur dans le pays concerné.

La page charge ...

Cabletron Systems DLM6C-AA Overview And Setup Manual

Ce manuel convient également à

Cabletron Systems DLM6C-AA Overview And Setup Manual

dans d''autres langues

Documents connexes

Autres documents