Zanussi ZWF91483WH Manuel utilisateur
- Catégorie
- Machines à laver
- Taper
- Manuel utilisateur
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible for any
injuries or damages that are the result of incorrect installation or
usage. Always keep the instructions in a safe and accessible
location for future reference.
CHILDREN AND VULNERABLE PEOPLE SAFETY
• This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning the use of the
appliance in a safe way and understand the hazards involved.
• Do not let children play with the appliance.
• Children aged 3 years and under must be kept away from this
appliance when it is in operation at all times.
• Keep all packaging away from children and dispose of it
appropriately.
• Keep detergents away from children.
• Keep children and pets away from the appliance when the door
is open.
• Children shall not carry out cleaning and user maintenance of
the appliance without supervision.
GENERAL SAFETY
• Do not change the specification of this appliance.
• Do not exceed the maximum load of 9 kg (refer to the
"Programme chart" chapter).
• The operating water pressure at the water entry point from the
outlet connection must be between 0.5 bar (0.05 MPa) and 8
bar (0.8 MPa).
• The ventilation opening in the base must not be covered by a
carpet, mat, or any floor covering.
• The appliance must be connected to the water mains using the
new supplied hose sets, or other new hose sets supplied by
the Authorised Service Centre.
2
• Old hose sets must not be reused.
• If the mains power supply cable is damaged, it must be
replaced by the manufacturer, its Authorised Service Centre or
similarly qualified persons to avoid an electrical hazard.
• Before any maintenance operation, deactivate the appliance
and disconnect the mains plug from the socket.
• Do not use high pressure water sprays and/or steam to clean
the appliance.
• Clean the appliance with a moist cloth. Use only neutral
detergents. Do not use abrasive products, abrasive cleaning
pads, solvents or metal objects.
SAFETY INSTRUCTIONS
INSTALLATION
• Remove all the packaging and the transit bolts.
• Keep the transit bolts in a safe place. If the
appliance is to be moved in future they must be
reattached to lock the drum to prevent internal
damage.
• Always take care when moving the appliance as
it is heavy. Always use safety gloves and
enclosed footwear.
• Do not install or use a damaged appliance.
• Follow the installation instruction supplied with
the appliance.
• Do not install or use the appliance where the
temperature can be less than 0°C or where it is
exposed to the weather.
• The floor area where the appliance is to be
installed must be flat, stable, heat resistant and
clean.
• Make sure that there is air circulation between
the appliance and the floor.
• Do not install the appliance directly over the
floor drain.
• Adjust the feet to have the necessary space
between the appliance and the flooring.
• Do not install the appliance where the appliance
door cannot be fully opened.
• Do not put a container to collect possible water
leakage under the appliance. Contact the
Authorised Service Centre to ensure which
accessories can be used.
ELECTRICAL CONNECTION
• The appliance must be earthed.
• Always use a correctly installed shockproof
socket.
• Make sure that the parameters on the rating
plate are compatible with the electrical ratings
of the mains power supply.
• Do not use multi-plug adapters and extension
cables.
• Make sure not to cause damage to the mains
plug and to the mains cable. Should the mains
cable need to be replaced, this must be carried
out by our Authorised Service Centre.
• Connect the mains plug to the mains socket
only at the end of the installation. Make sure that
there is access to the mains plug after the
installation.
• Do not touch the mains cable or the mains plug
with wet hands.
• Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
• This appliance complies with the E.E.C.
Directives.
WATER CONNECTION
• Do not cause damage to the water hoses.
• Before connection to new pipes, pipes not used
for a long time, where repair work has been
carried out or new devices fitted (water meters,
etc.), let the water flow until it is clean and clear.
• Ensure that there are no visible water leaks
during and after the first use of the appliance.
• Do not use an extension hose if the inlet hose is
too short. Contact the service centre for the
replacement of the inlet hose.
• You can extend the drain hose to maximum 400
cm. Contact the service centre for the other
drain hose and the extension.
3
USE
WARNING! Risk of injury, electrical
shock, fire, burns or damage to the
appliance.
• This appliance is for household use only.
• Follow the safety instructions on the detergent
packaging.
• Do not put flammable products or items that are
wet with flammable products in, near or on the
appliance.
• Make sure that all metal objects are removed
from the laundry.
• Do not wash fabrics which are heavily soiled
with oil, grease or other greasy substances. It
can damage rubber parts of the washing
machine. Prewash such fabrics by hand before
loading them into the washing machine.
• Do not touch the glass door while a programme
is in operation. The glass can get hot.
SERVICE
• To repair the appliance contact an Authorised
Service Centre.
• Use original spare parts only.
DISPOSAL
WARNING! Risk of injury or
suffocation.
• Disconnect the appliance from the mains
electrical and water supplies.
• Cut off the mains electrical cable close to the
appliance and dispose of it.
• Remove the door catch to prevent children or
pets from becoming trapped in the drum.
• Dispose of the appliance in accordance with
local requirements for the disposal of Waste
Electrical and Electronic Equipment (WEEE).
PRODUCT DESCRIPTION
APPLIANCE OVERVIEW
1 2 3
5
6
4
1
Worktop
2
Detergent dispenser
3
Control panel
4
Door handle
5
Rating plate
6
Feet for levelling the appliance
FIXING PLATE KIT (4055171146)
Available from your authorised dealer.
If you install the appliance on a plinth, secure the
appliance in the fixing plates.
Read carefully the instructions supplied with the
accessory.
4
CONTROL PANEL
CONTROL PANEL DESCRIPTION
Finish In
P
1400
90°
60°
40°
30°
1200
800
On/Off
Synthetics
Cottons
Delicates
Wool/Handwash
Cotton ECO
Mix 20°Mix 20°
Duvets
987621 3 4 5
1
On/Off button
2
Programme selection touchpad
3
Temperature selection touchpad
4
Spin selection touchpad
5
Options selection touchpad
6
Start/Pause touchpad
7
Finish in touchpad
8
Display
9
Door locked indicator
DISPLAY
Finish In
A
D
B C
A. The time area:
• : the programme duration
• : the "finish in" time
• : the alarm codes
• : the message of error
• : the programme is completed.
B. The child lock indicator:
• The indicator comes on when you activate
this device.
C. The extra rinse indicator:
• The indicator comes on when you activate
this option.
D. The Finish In touchpad.
5
PROGRAMME CHART
Programme
Temperature range
Maximum load
Maximum spin
speed
Programme description
(Type of load and soil level)
30'@30°
30°C
3 kg
800 rpm
A short cycle for synthetic and delicate items with
light soil level or for items to freshen up.
Cottons
90°C - Cold
9 kg
1400 rpm
White cotton and coloured cotton. Normal soil and
light soil.
Cotton Eco
1)
60°C - 40°C
9 kg
1400 rpm
White cotton and fast-coloured cotton. Normal soil.
The energy consumption decreases and the time of the
washing programme is extended.
Synthetics
60°C - Cold
3,5 kg
1200 rpm
Synthetic items or mixed fabric items. Normal soil.
Delicates
40°C - Cold
3,5 kg
1200 rpm
Delicate fabrics such as acrylics, viscose and mixed
fabrics requiring gentler washing. Normal soil.
Wool / Handwash
40°C - Cold
2 kg
1200 rpm
Machine washable wool, hand washable wool and
other fabrics with «hand washing» care symbol
2)
.
Duvets
60°C - Cold
3 kg
800 rpm
Special programme for one synthetic blanket, duvet,
bedspread and so on.
Mix 20°
20°C
2 kg
1200 rpm
Special programme for cotton, synthetic and mixed fabrics
with light soil. Set this programme to decrease the energy
consumption. Make sure that the detergent is for low tem-
perature in order to have good washing results
3)
.
1) Standard programmes for the Energy Label consumption values. According to regulation
1061/2010, these programmes are respectively the «Standard 60°C cotton programme» and the «Stand-
ard 40°C cotton programme». They are the most efficient programmes in terms of combined energy and
water consumption for washing normally soiled cotton laundry.
The water temperature of the washing phase may differ from the temperature declared for the
selected programme.
2) During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't
rotate or doesn't rotate properly, but this is normal for this programme.
3) No temperature indicator is on .
Programme options compatibility
Programme
1)
30'@30° ■ ■ ■ ■
6
Programme
1)
■ ■ ■ ■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■ ■
1) When you set this option, we recommend that you decrease the quantity of the laundry. It is possible to
keep the full load but the washing results can be unsatisfactory. Recommended load: cotton: 4,5 kg, syn-
thetics and delicates: 2,5 kg.
CONSUMPTION VALUES
Stated values are obtained in laboratory conditions with relevant standards. Different cau-
ses can change the data: the quantity and type of laundry and ambient temperature. Wa-
ter pressure, the supply voltage and the temperature of inlet water may also affect the
washing programme duration.
Technical specifications may be changed without prior notice to improve the quality of
product.
At the start of the programme, the display shows the programme duration for the maxi-
mum load capacity.
During the washing phase the programme duration is automatically calculated and can be
greatly reduced if the laundry load is lower than the maximum load capacity (e.g. Cotton
60°C, maximum load capacity 9 kg, the programme duration exceeds 2 hours; actual load
1 kg, the programme duration will be less than 1 hour).
When the appliance is calculating the real programme duration a dot flashes in the dis-
play.
Programmes Load (kg)
Energy con-
sumption
(kWh)
Water con-
sumption (li-
tre)
Approximate
programme
duration (mi-
nutes)
Remaining
moisture (%)
1)
Cottons
60°C
9 1,58 84 240 52
7
Programmes Load (kg)
Energy con-
sumption
(kWh)
Water con-
sumption (li-
tre)
Approximate
programme
duration (mi-
nutes)
Remaining
moisture (%)
1)
Cottons
40°C
9 1,30 82 210 52
Synthetics
40°C
3,5 0,74 61 140 35
Delicates
40°C
3,5 0,54 62 95 35
Wool/Handwash
2)
30°C
2 0,42 62 75 30
Standard cotton programmes
Standard 60°C cot-
ton
9 0,95 53 248 52
Standard 60°C cot-
ton
4,5 0,64 43 209 52
Standard 40°C cot-
ton
4,5 0,61 44 205 52
1) At the end of spin phase.
2) Not available for some models.
Off Mode (W) Left On Mode (W)
0.30 0.30
The information given in the chart above is compliant with the EU Commission regulation 1015/2010
implementing directive 2009/125/EC
OPTIONS
TEMPERATURE
With this option you can change the default
temperature.
Indicator
= cold water.
The indicator of the set temperature comes on.
SPIN
With this option you can change the default spin
speed.
The indicator of the set speed comes on.
Additional spin options:
No Spin
• Set this option to deactivate all spin phases.
Only the drain phase is available.
• The related indicator comes on.
• Set this option for very delicate fabrics.
• The rinses phase uses more water for some
washing programmes.
Rinse Hold
• Set this option to prevent the laundry creases.
• The related indicator comes on.
8
• There is a water in the drum when the
programme is completed.
• The drum turns regularly to prevent the laundry
creases.
• The door stays locked. You must drain the water
to unlock the door.
To drain the water refer to ‘At the end
of the programme’.
QUICK
With this option you can decrease the programme
duration.
Use this option for items with light soil or items to
refresh.
The related indicator comes on.
INTENSIVE
With this option you can wash very soiled laundry.
The washing cycle lasts longer with this option.
The related indicator comes on.
EASY IRON
The appliance carefully washes and spins the
laundry to prevent the creases.
The appliance decreases the spin speed, uses
more water and adapts the programme duration to
the type of laundry.
The related indicator comes on.
RINSE ONLY
With this option you can perform only a last rinse of
a selected washing programme.
If you set also the Extra Rinse function (
) the
appliance adds two or more rinses.
The related indicator comes on.
DRAIN AND SPIN
With this option you can perform the spin and drain
cycle.
This spin phase is suitable to the washing
programme you set.
If you set also the No Spin ( )
option, the appliance only drains.
FINISH IN
With this option you can set the number of hours in
which you would like your washing programme to
be completed.
You can set from minimum 3 hours to maximum 20
hours.
The display shows the number of hours and the
indicator above the button is on.
EXTRA RINSE
With this option you can add some rinses to a
washing programme.
Use this option for persons allergic to detergents
and in areas where the water is soft.
The related indicator comes on.
1)
SETTINGS
PERMANENT EXTRA RINSE
With this option you can permanently have an extra
rinse when you set a new programme.
• To activate/deactivate this option touch the
buttons
and at the same time until the
indicator comes on/goes off.
CHILD LOCK
With this option you can prevent that the children
play with the control panel.
• To activate/deactivate this option, touch the
buttons and at the same time until the
indicator comes on/goes off.
Activate this option after you touch the button :
the buttons are locked (except for the button ) .
This option stays active even when you
switch off the appliance.
ACOUSTIC SIGNALS
The acoustic signals operate when:
1) See in "Settings" how to activate this option.
9
• The programme is completed.
• The appliance has a malfunction.
To deactivate/activate the acoustic signals,
touch the buttons and at the same time for 4
seconds.
If you deactivate the acoustic signals,
they continue operate when the
appliance has a malfunction.
BEFORE FIRST USE
1. Connect the mains plug to the mains socket.
2. Open the water tap.
3. Put a small quantity of detergent in the
compartment for washing phase.
4. Set and start a programme for cotton at the
highest temperature without laundry.
This removes all possible dirt from the drum and the
tub.
DAILY USE
WARNING! Refer to Safety chapters.
LOADING THE LAUNDRY
Open the water tap. Connect the mains plug to the
mains socket.
1. Pull the door handle to open the appliance
door.
2. Put the laundry in the drum, one item at a time.
3. Shake the items before you put them in the
appliance.
Make sure not to put too much laundry in the drum.
Refer to max. loads indicated in "Programme chart".
4. Close the door.
CAUTION! Make sure that no laundry
stays between the seal and the door.
There is a risk of water leakage or
damage to the laundry.
Washing heavily oiled, greasy stains
could cause damage rubber parts of
the washing machine.
USING DETERGENT AND ADDITIVES
1. Measure out the de-
tergent and the fabric
conditioner.
2. Put the detergent
and the fabric condi-
tioner into the com-
partments.
3. Carefully close the
detergent drawer.
DETERGENT COMPARTMENTS
Detergent compartment for
washing phase.
If you use liquid detergent, put it
immediately before you start the
programme.
Compartment for liquid additives
(fabric conditioner, starch).
CAUTION! Do not
exceed the MAX
level.
Flap for powder or liquid deter-
gent.
10
LIQUID OR POWDER DETERGENT
A
The default position of
the flap is A (powder de-
tergent).
To use liquid detergent:
1. Remove the drawer.
Push the drawer edge in
the place with the arrow
(PUSH) to remove the
drawer easily.
B
2. Adjust the flap in posi-
tion B.
3. Put back the drawer in
the recess.
When you use the liquid detergent:
• Do not use gelatinous or thick liq-
uid detergents.
• Do not put more liquid then 120
ml.
• Do not set the delay start.
A
When the flap is in posi-
tion B and you want to
use powder detergent:
1. Remove the drawer.
2. Adjust the flap in po-
sition A.
3. Put back the drawer
in the recess.
• Measure out the detergent and the fabric condi-
tioner.
• Put the detergent and the fabric conditioner into
the compartments.
• Carefully close the detergent drawer.
ACTIVATING THE APPLIANCE
Press and hold for a couple of seconds the On/Off
button to activate or deactivate the appliance.
A tune sounds when the appliance is activated.
The display shows the word On.
SETTING A PROGRAMME
1. Touch the programme button and set the
programme:
• The indicator of the button flashes.
• The display shows the programme duration.
2. If necessary, change the temperature and the
spin speed or add available options. When you
activate an option, the indicator of the set
option comes on.
If you set something incorrect, the
display shows the message .
STARTING A PROGRAMME WITHOUT THE
FINISH IN OPTION
Touch the button .
• The indicator of the button stops to
flash and stays on.
• The programme starts, the door locks, the
indicator is on.
• The drain pump can operate for a short time
at the beginning of the washing cycle.
After approximately 15 minutes from
the start of the programme:
• The appliance adjusts automatically
the programme duration agree with
the laundry load.
• The display shows the new value.
STARTING A PROGRAMME WITH THE
FINISH IN OPTION
1. Touch the button again and again to
choose the number of hours in which you want
the washing cycle to be finished.
The display shows the number of hours you set
(e.g.
) and the indicator above the button is
on to show that his option is active.
2. Touch the button :
• The door is locked.
• The appliance starts the countdown.
• When the countdown is completed, the
programme starts automatically.
11
You can cancel or change the set of
the Finish In option before you touch
the button . After touching the
button you can only cancel the
Finish In option.
To cancel the the Finish In option:
a. Touch the button to set the appliance
to pause. The indicator of button
flashes.
b. Touch the button
until the indicator
above this button goes off.
Touch the button again to start the
programme immediately.
INTERRUPTING A PROGRAMME AND
CHANGING THE OPTIONS
You can change only some options before they
operate.
1. Touch .
The indicator of this button flashes.
2. Change the options. If you change any option
the Finish In option (if set) will be disabled.
3. Touch again.
The programme continues.
CANCELLING A PROGRAMME
1. Press the button On/Off for some seconds to
cancel the programme and to deactivate the
appliance.
2. Press the same button again to activate the
appliance. Now, you can set a new washing
programme.
Before starting the new programme
the appliance could drain the water. In
this case, make sure that the detergent
is still in the detergent compartment, if
not fill the detergent again.
OPENING THE DOOR
While a programme (or the ) operates, the
appliance door is locked. The indicator is on.
CAUTION! If the temperature and
level of the water in the drum are too
high, you cannot open the door.
To open the door during the first minutes of
the cycle (or when the operates) :
1. Touch the button to pause the appliance.
2. Wait until the indicator goes off.
3. You can open the door.
4. Close the door and touch the button again.
The programme (or the ) continues.
AT THE END OF THE PROGRAMME
• The appliance stops automatically.
• The acoustic signal operates (if it is activated).
• In the display comes on.
• The indicator of the button goes off.
• The door lock indicator goes off.
• You can open the door.
• Remove the laundry from the appliance. Make
sure that the drum is empty.
• Press the button for some seconds to
deactivate the appliance.
• Close the water tap.
• Keep the door and the detergent drawer ajar, to
prevent the mildew and odours.
The washing programme is completed, but
there is water in the drum:
• The drum turns regularly to prevent the creases
in the laundry.
• The indicator flashes to remind you to drain
the water.
• The door lock indicator is on. The indicator
of button flashes. The door stays locked.
• You must drain the water to open the door.
Draining the water:
1. To drain the water.
• Touch the button
. The appliance
drains the water and spins with the
maximum spin speed for selected washing
programme.
• Alternatively, touch the button to change
the spin speed and then touch the button
. The appliance drains the water and
spins. If you set , the appliance only
drains.
2. When the programme is completed and the
door lock indicator goes off, you can open
the door.
3. Press the button for some seconds to
deactivate the appliance.
The appliance drains and spins
automatically after approximately 18
hours (except for Wool programme).
12
AUTO-OFF OPTION
The AUTO-OFF stand-by option automatically
deactivates the appliance to decrease the energy
consumption. All the indicators and the display go
off when :
• You do not use the appliance for 5 minutes
before you touch .
Press the button to activate the appliance
again.
• After 5 minutes from the end of the washing
programme.
Press the button to activate the appliance
again.
The display shows the end of the last set
programme.
Touch the button if you want to set a new
cycle.
HINTS AND TIPS
THE LAUNDRY LOAD
• Divide the laundry in: white, coloured,
synthetics, delicates and wool.
• Obey the washing instructions that are on the
laundry care labels.
• Do not wash white and coloured items together.
• Some coloured items can discolour with the first
wash. We recommend that you wash them
separately for the first times.
• Button up pillowcases, close zippers, hooks and
poppers. Tie up belts.
• Empty the pockets and unfold the items.
• Turn multilayered fabrics, wool and items with
painted illustrations inside out.
• Remove hard stains with a special detergent.
• Wash and pre-treat heavy soil stains before
putting items in drum
• Be careful with the curtains. Remove the hooks
and put the curtains in a washing bag or
pillowcase.
• Do not wash laundry without hems or with cuts.
Use a washing bag to wash small and/or
delicate items (e.g. underwired bras, belts,
tights, etc. ).
• A very small load can cause balance problems
with the spin phase. If this occurs, adjust
manually the items in the tub and start the spin
phase again.
STUBBORN STAINS
For some stains, water and detergent is not
sufficient.
We recommend that you pre-treat these stains
before you put the items in the appliance.
Special stain removers are available. Use the
special stain remover that is applicable to the type
of stain and fabric.
DETERGENTS AND ADDITIVES
• Only use detergents and additives specially
made for washing machines:
– powder detergents for all types of fabric,
– powder detergents for delicate fabrics (40
°C max) and woollens,
– liquid detergents, preferably for low
temperature wash programmes (60 °C max)
for all types of fabric, or special for woollens
only.
• Do not mix different types of detergents.
• To help the environment, do not use more than
the correct quantity of detergent.
• Obey the instructions that you find on the on
packaging of these products.
• Use the correct products for the type and colour
of the fabric, the programme temperature and
the level of soil.
• If your appliance does not have the detergent
dispenser with the flap device, add the liquid
detergents with a dosing ball (supplied by the
detergent's manufacturer).
ECOLOGICAL HINTS
• Always start a washing programme with the
maximum load of laundry allowed.
• If necessary, use a stain remover when you set a
programme with a low temperature.
• To use the correct quantity of detergent, check
the water hardness of your domestic system.
Refer to "Water hardness".
WATER HARDNESS
If the water hardness in your area is high or
moderate, we recommend that you use a water
softener for washing machines. In areas where the
water hardness is soft it is not necessary to use a
water softener.
To know the water hardness in your area, contact
your local water authority.
Use the correct quantity of the water softener.
Obey the instructions that you find on the
packaging of the product.
13
CARE AND CLEANING
WARNING! Refer to Safety chapters.
EXTERNAL CLEANING
Clean the appliance with soap and warm water
only. Fully dry all the surfaces.
CAUTION! Do not use alcohol,
solvents or chemical products.
DESCALING
If the water hardness in your area is high or
moderate, we recommend that you use a water
descaling product for washing machines.
Regularly examine the drum to prevent limescale
and rust particles.
To remove rust particles use only special products
for washing machines. Do this separately from the
laundry wash.
Always obey the instructions that you
find on the packaging of the product.
MAINTENANCE WASH
With the low temperature programmes it is possible
that some detergent stays in the drum. Perform a
maintenance wash regularly. To do this:
• Remove all laundry from the drum.
• Select the cotton programme with the highest
temperature with a small quantity of detergent.
DOOR SEAL
Regularly examine the
seal and remove all ob-
jects from the inner part.
CLEANING THE DETERGENT DISPENSER
1 2 3 4
5 6
14
CLEANING THE INLET HOSE AND THE VALVE FILTER
1
2
3
1 2 3
45°
20°
4
FROST PRECAUTIONS
If the appliance is installed in an area where the
temperature can be less than 0 °C, remove the
remaining water from the inlet hose and the drain
pump.
Do this procedure also when you want
to do the emergency drain.
1. Disconnect the mains plug from the mains
socket.
2. Remove the water inlet hose.
3. Remove the drain hose from the rear support
and unhook it from sink or spigot.
4. Put the ends of the drain and inlet hose in a
container. Let the water flow out of the hoses.
5. When no more water flows, install the inlet
hose and the drain hose again.
WARNING! Make sure that the
temperature is more than 0 °C before
you use the appliance again. The
manufacturer is not responsible for
damages caused by low temperatures.
TROUBLESHOOTING
WARNING! Refer to Safety chapters.
INTRODUCTION
The appliance does not start or it stops during
operation.
First try to find a solution to the problem (refer to
the table). If the problem persists, contact the
Authorised Service Centre.
With some problems, the acoustic signals
operate and the display shows an alarm
code:
•
- The appliance does not fill with water
properly. Start the appliance again by pressing
button. After 10 seconds the door will be
unlocked.
• - The appliance does not drain the water.
• - The appliance door is open or not
closed correctly. Please check the door!
If the appliance is overloaded,
remove some items from the drum
and/or keep pressed the door and
push the button at the same
time until the indicator stops
flashing (see the picture below).
• - The mains supply is unstable. Wait until
the mains supply is stable.
• - No communication between electronic
elements of the appliance. Switch off and
switch on again. The programme was not
finished properly or the appliance stopped too
15
early. If the alarm code appears again, contact
the Authorised Service Centre.
WARNING! Deactivate the appliance
before you do the checks.
POSSIBLE FAILURES
Problem Possible solution
The programme does not
start.
• Make sure that the mains plug is connected to the mains socket.
• Make sure that the appliance door is closed.
• Make sure that there is not a damaged fuse in the fuse box.
• Make sure that the Start/Pause has been pressed.
• If the delay start is set, cancel the setting or wait for the end of
countdown.
• Deactivate the Child Lock function if it is on.
The appliance does not fill
with water properly.
• Make sure that the water tap is open.
• Make sure that the pressure of the water supply is not too low. For
this information, contact your local water authority.
• Make sure that the water tap is not clogged.
• This problem may be caused by the filter of the inlet hose or the
valve drain filter which may be clogged. Refer to “Care and clean-
ing”. If problem remains please contact the Authorised Service
Centre.
• Make sure that the inlet hose has no kinks or bends.
• Make sure that the connection of the water inlet hose is correct.
The appliance does not
drain the water.
• Make sure that the sink spigot is not clogged.
• Make sure that the drain hose has no kinks or bends.
• Make sure that the connection of the drain hose is correct.
• Set the drain option if you set a programme without drain phase.
• Set the drain option if you set an option which ends with water in
the drum.
• This problem may be caused by the clogged drain filter. Please
contact the Authorised Service Centre.
The spin phase does not
operate or the washing cy-
cle lasts longer than usual-
ly.
• Adjust manually the items in the tub and start the spin phase again.
This problem may be caused by balance problems.
• Set the spin option.
• Set the drain option if you set an option which ends with water in
the drum.
• This problem may be caused by the clogged drain filter. Please
contact the Authorised Service Centre.
There is water on the floor. • Make sure that the couplings of the water hoses are tight and there
is not water leakages.
• Make sure that the water inlet hose and the drain hose have no
damages.
• Make sure you use the correct detergent and the correct quantity of
it.
You cannot open the appli-
ance door.
• Make sure that the washing programme is finished.
• Set the drain or the spin option if there is water in the drum.
• Do the emergency drain procedure. See "Frost precautions" (in
"Care and Cleaning" chapter).
16
Problem Possible solution
The appliance makes an
unusual noise.
• Make sure the levelling of the appliance is correct. Refer to 'Installa-
tion instruction'.
• Make sure that the packaging and/or the transit bolts are removed.
Refer to 'Installation instruction'.
• Add more laundry in the drum. The load may be too small.
The appliance fills with wa-
ter and drain immediately.
• Make sure that the drain hose is in the correct position. The end of
the hose may be too low. Refer to 'Installation instruction'.
The cycle is shorter than
the time displayed.
• The appliance calculates a new time according to the laundry load.
See the ‘Consumption Values’ chapter.
The cycle is longer than
the time displayed.
• An unbalanced laundry load increases the duration time. This is a
normal behaviour of the appliance.
The washing results are
not satisfactory.
• Increase the detergent quantity or use a different detergent.
• Use special products to remove the stubborn stains before you
wash the laundry.
• Make sure that you set the correct temperature.
• Decrease the laundry load.
You cannot set an option. • Make sure that you press only the wanted touch button(s).
After the check, activate the appliance. The
programme continues from the point of interruption.
If the problem occurs again, contact the Authorised
Service Centre.
If the display shows other alarm codes. Deactivate
and activate the appliance. If the problem
continues, contact the Authorised Service Centre.
SERVICE
We recommend the use of original spare parts.
When contacting the Authorised Service Centre,
make sure that these data are available. You can
find the information on the rating plate: model, PNC
and Serial Number. (Mod., Prod. No., Ser. No.)
TECHNICAL DATA
Dimension Width/ Height/ Depth/ To-
tal depth
600 mm/ 850 mm/ 600 mm/ 660 mm
Electrical connection Voltage
Overall power
Fuse
Frequency
220 - 240 V
2200 W
10 A
50 Hz
Level of protection against ingress of solid particles and
moisture ensured by the protective cover, except where
the low voltage equipment has no protection against
moisture
IPX4
Water supply pressure Minimum
Maximum
0,5 bar (0,05 MPa)
8 bar (0,8 MPa)
Water supply
1) Cold water
Maximum Load Cotton 9 kg
Energy Efficiency Class A+++ -20%
17
Spin Speed Maximum 1400 rpm
1) Connect the water inlet hose to a water tap with a 3/4'' thread.
ENVIRONMENTAL CONCERNS
Recycle materials with the symbol . Put the
packaging in relevant containers to recycle it. Help
protect the environment and human health by
recycling waste of electrical and electronic
appliances. Do not dispose of appliances marked
with the symbol with the household waste.
Return the product to your local recycling facility or
contact your municipal office.
18
INFORMATIONS DE SÉCURITÉ
Avant d'installer et d'utiliser cet appareil, lisez soigneusement les
instructions fournies. Le fabricant ne pourra être tenu pour
responsable des blessures et dégâts résultant d'une mauvaise
installation ou utilisation. Conservez toujours les instructions dans
un lieu sûr et accessible pour vous y référer ultérieurement.
SÉCURITÉ DES ENFANTS ET DES PERSONNES
VULNÉRABLES
• Cet appareil peut être utilisé par des enfants âgés d'au moins 8
ans et par des personnes ayant des capacités physiques,
sensorielles ou mentales réduites ou dénuées d’expérience ou
de connaissance, s'ils (si elles) sont correctement surveillé(e)s
ou si des instructions relatives à l'utilisation de l'appareil en
toute sécurité leur ont été données et si les risques encourus
ont été appréhendés.
• Ne laissez pas les enfants jouer avec l'appareil.
• Les enfants de moins de 3 ans doivent être tenus éloignés de
l'appareil en permanence lorsqu'il est en fonctionnement.
• Ne laissez pas les emballages à la portée des enfants et jetez-
les convenablement.
• Ne laissez pas les détergents à la portée des enfants.
• Tenez les enfants et les animaux éloignés de l'appareil lorsque
la porte est ouverte.
• Le nettoyage et l'entretien par l'usager ne doivent pas être
effectués par des enfants sans surveillance.
SÉCURITÉ GÉNÉRALE
• Ne modifiez pas les caractéristiques de cet appareil.
• Respectez la charge maximale de 9 kg (reportez-vous au
chapitre « Tableau des programmes »).
• La pression de l'eau en service au niveau du point d'entrée en
provenance de l'arrivée d'eau doit être comprise entre 0,5 bar
(0,05 MPa) et 8 bar (0,8 MPa).
19
• Les orifices d'aération situés à la base ne doivent pas être
obstrués par de la moquette, un tapis, ou tout type de
revêtement de sol.
• L'appareil doit être raccordé à l'arrivée d'eau à l'aide des tuyaux
neufs fournis, ou d'autres tuyaux neufs fournis par le service
après-vente agréé.
• N'utilisez pas de tuyaux provenant d'anciens appareils.
• Si le câble d'alimentation est endommagé, il doit être remplacé
par le fabricant, un service de maintenance agréé ou un
technicien qualifié afin d'éviter tout danger lié à l'électricité.
• Avant toute opération d'entretien, éteignez l'appareil et
débranchez la fiche de la prise secteur.
• Ne pulvérisez pas d'eau ni de vapeur à haute pression pour
nettoyer l'appareil.
• Nettoyez l'appareil avec un chiffon humide. Utilisez uniquement
des produits de lavage neutres. N'utilisez pas de produits
abrasifs, de tampons à récurer, de solvants ni d'objets
métalliques.
CONSIGNES DE SÉCURITÉ
INSTALLATION
• Retirez l'intégralité de l'emballage et les boulons
de transport.
• Conservez les boulons de transport en lieu sûr.
Si l'appareil doit être de nouveau déplacé, les
boulons doivent être réutilisés pour maintenir le
tambour en place et éviter tout dégât interne.
• Soyez toujours vigilants lorsque vous déplacez
l'appareil car il est lourd. Utilisez toujours des
gants de sécurité et des chaussures fermées.
• N'installez pas et ne branchez pas un appareil
endommagé.
• Suivez scrupuleusement les instructions
d'installation fournies avec l'appareil.
• N'installez pas l'appareil ou ne l'utilisez pas dans
un endroit où la température ambiante est
inférieure à 0 °C ou dans un endroit exposé aux
intempéries.
• L'appareil doit être installé sur un sol plat,
stable, résistant à la chaleur et propre.
• Assurez-vous que de l'air circule entre l'appareil
et le sol.
• N'installez pas l'appareil directement au-dessus
d'une évacuation dans le sol.
• Réglez les pieds pour laisser un espace
suffisant entre l'appareil et le sol.
• N'installez pas l'appareil dans un endroit où il ne
pourrait pas être complètement ouvert.
• Ne placez aucun récipient sous l'appareil pour
récupérer tout éventuel écoulement. Contactez
le service après-vente agréé pour connaître les
accessoires disponibles.
BRANCHEMENT ÉLECTRIQUE
• L'appareil doit être relié à la terre.
• Utilisez toujours une prise de courant de
sécurité correctement installée.
• Vérifiez que les paramètres figurant sur la
plaque signalétique correspondent aux données
électriques de votre réseau.
• N'utilisez pas d'adaptateurs multiprises ni de
rallonges.
• Veillez à ne pas endommager la fiche secteur ni
le câble d'alimentation. Le remplacement du
câble d'alimentation de l'appareil doit être
effectué par notre service après-vente agréé.
• Ne branchez la fiche d'alimentation à la prise de
courant qu'à la fin de l'installation. Assurez-vous
20
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
Zanussi ZWF91483WH Manuel utilisateur
- Catégorie
- Machines à laver
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Zanussi ZWF91483WH User manual