Zanussi ZWF81467I Manuel utilisateur

Marque: Zanussi

Modèle: ZWF81467I

Catégorie: Machines à laver

Taper: Manuel utilisateur

GETTING

STARTED?

EASY.

User Manual

ZWF81467I

EN User Manual 2

Washing Machine

FR Notice d'utilisation 22

Lave-linge

SAFETY INFORMATION

Before the installation and use of the appliance, carefully read the

supplied instructions. The manufacturer is not responsible for any

injuries or damage that are the result of incorrect installation or

usage. Always keep the instructions in a safe and accessible

location for future reference.

CHILDREN AND VULNERABLE PEOPLE SAFETY

• This appliance can be used by children aged from 8 years and

above and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have

been given supervision or instruction concerning the use of the

appliance in a safe way and understand the hazards involved.

• Children between 3 and 8 years of age and persons with very

extensive and complex disabilities shall be kept away from the

appliance unless continuously supervised.

• Children of less than 3 years of age should be kept away from

the appliance unless continuously supervised.

• Do not let children play with the appliance.

• Keep all packaging away from children and dispose of it

appropriately.

• Keep detergents away from children.

• Keep children and pets away from the appliance when the door

is open.

• If the appliance has a child safety device, it should be activated.

• Children shall not carry out cleaning and user maintenance of

the appliance without supervision.

GENERAL SAFETY

• Do not change the specification of this appliance.

• This appliance is intended to be used in household and similar

applications such as:

– staff kitchen areas in shops, offices and other working

environments;

– by clients in hotels, motels, bed & breakfast and other

residential type environments;

– areas for communal use in blocks of flats or in launderettes.

• Do not exceed the maximum load of 8 kg (refer to the

"Programme chart" chapter).

• The operating water pressure at the water entry point from the

outlet connection must be between 0.5 bar (0.05 MPa) and 8

bar (0.8 MPa).

• The ventilation opening in the base must not be covered by a

carpet, mat, or any floor covering.

• The appliance must be connected to the water mains using the

new supplied hose sets, or other new hose sets supplied by

the Authorised Service Centre.

• Old hose sets must not be reused.

• If the mains power supply cable is damaged, it must be

replaced by the manufacturer, its Authorised Service Centre or

similarly qualified persons to avoid an electrical hazard.

• Before any maintenance operation, deactivate the appliance

and disconnect the mains plug from the socket.

• Do not use high pressure water sprays and/or steam to clean

the appliance.

• Clean the appliance with a moist cloth. Use only neutral

detergents. Do not use abrasive products, abrasive cleaning

pads, solvents or metal objects.

SAFETY INSTRUCTIONS

INSTALLATION

The installation must comply with

relevant national regulations.

• Remove all the packaging and the transit bolts

including rubber bush with plastic spacer.

• Keep the transit bolts in a safe place. If the

appliance is to be moved in the future they must

be reattached to lock the drum to prevent an

internal damage.

• Always take care when moving the appliance as

it is heavy. Always use safety gloves and

enclosed footwear.

• Follow the installation instructions supplied with

the appliance.

• Do not install or use a damaged appliance.

• Do not install or use the appliance where the

temperature can be less than 0°C or where it is

exposed to the weather.

• The floor area on which the appliance is to be

installed must be flat, stable, heat resistant and

clean.

• Make sure that there is air circulation between

the appliance and the floor.

• When the appliance is in its permanent position,

check if it is levelled correctly with the aid of a

spirit level. If it is not, adjust the feet accordingly.

• Do not install the appliance directly above a

floor drain.

• Do not spray water on the appliance and do not

expose it to excessive humidity.

• Do not install the appliance where the appliance

door cannot be fully opened.

• Do not put a closed container to collect

possible water leakage under the appliance.

Contact the Authorised Service Centre to

ensure which accessories can be used.

ELECTRICAL CONNECTION

WARNING! Risk of fire and electric

shock.

• The appliance must be earthed.

• Always use a correctly installed shockproof

socket.

• Make sure that the parameters on the rating

plate are compatible with the electrical ratings

of the mains power supply.

• Do not use multi-plug adapters and extension

cables.

• Make sure not to cause damage to the mains

plug and to the mains cable. Should the mains

cable need to be replaced, this must be carried

out by our Authorised Service Centre.

• Connect the mains plug to the mains socket

only at the end of the installation. Make sure that

there is access to the mains plug after the

installation.

• Do not touch the mains cable or the mains plug

with wet hands.

• Do not pull the mains cable to disconnect the

appliance. Always pull the mains plug.

• This appliance complies with the E.E.C.

Directives.

WATER CONNECTION

• Do not cause damage to the water hoses.

• Before connection to new pipes, pipes not used

for a long time, where repair work has been

carried out or new devices fitted (water meters,

etc.), let the water flow until it is clean and clear.

• Ensure that there are no visible water leaks

during and after the first use of the appliance.

• Do not use an extension hose if the inlet hose is

too short. Contact the Authorised Service

Centre for the replacement of the inlet hose.

• When unpacking the appliance, It is possible to

see water flowing from the drain hose. This is

due to the testing of the appliance with the use

of water in the factory.

• You can extend the drain hose to maximum 400

cm. Contact the Authorised Service Centre for

the other drain hose and the extension.

• Make sure that there is access to the tap after

the installation.

USE

WARNING! Risk of injury, electric

shock, fire, burns or damage to the

appliance.

• Follow the safety instructions on the detergent

packaging.

• Do not put flammable products or items that are

wet with flammable products in, near or on the

appliance.

• Do not wash fabrics which are heavily soiled

with oil, grease or other greasy substances. It

can damage rubber parts of the washing

machine. Prewash such fabrics by hand before

loading them into the washing machine.

• Do not touch the glass door while a programme

operates. The glass can get hot.

• Make sure that all metal objects are removed

from the laundry.

SERVICE

• To repair the appliance contact the Authorised

Service Centre.

• Use original spare parts only.

DISPOSAL

WARNING! Risk of injury or

suffocation.

• Disconnect the appliance from the mains

electrical and water supplies.

• Cut off the mains electrical cable close to the

appliance and dispose of it.

• Remove the door catch to prevent children or

pets from becoming trapped in the drum.

• Dispose of the appliance in accordance with

local requirements for the disposal of Waste

Electrical and Electronic Equipment (WEEE).

PRODUCT DESCRIPTION

APPLIANCE OVERVIEW

1 2 3

Worktop

Detergent dispenser

Control panel

Door handle

Rating plate

Quick Reminder sticker

Feet for levelling the appliance

FIXING PLATE KIT (4055171146)

Available from your authorised dealer.

If you install the appliance on a plinth, secure the

appliance in the fixing plates.

Read carefully the instructions supplied with the

accessory.

EASY START

SPECIAL FEATURES

Your new washing machine meets all modern

requirements for an effective treatment of laundry

with low water, energy and detergent consumption

and will care for fabrics.

This appliance is designed with a self cleaning

draining system, allowing light fluff fibers that fall

off the clothes to be drained out with the water, in

such a way that there is no need to access this

area for regular maintenance and cleaning. Refer to

chapter 'Care and Cleaning' for best maintenance

and care of the appliance.

The AutoSense System automatically adjusts the

programme duration to the laundry in the drum to

achieve perfect washing results in the minimum

possible time.

CONTROL PANEL DESCRIPTION

תרצוקמ תינכות

יוביכ/הלעפה

תויורשפא

תופסונ

תרבגומ הפיטש

לק ץוהיג

דבלב הפיטש

זוקינו הטיחס

דיב הסיבכ/רמצ

תוקד 20 ןונעיר

םיברועמ םידב

רוטרפמט

הטיחס

ב -םייס

הנתוכ

ינוכסח הנתוכ

םינידע

יטטניס

81 2 3 4 5

On / Off button

Programme selection touchpad

Temperature touchpad

Spin selection touchpad

Finish at touchpad ( םייס -ב )

Start/Pause touchpad

Options selection touchpad

Display

DISPLAY

A B C E

A. The Temperature area:

: Temperature indicator

: Cold water indicator

B. : The permanent extra rinse indicator

C. The spin area:

•

: The spin speed indicator

• : The No Spin indicator

• : The Rinse Hold indicator

• : The Extra Silent indicator

D. The time area:

• : The programme duration

• : The time of cycle finish (when the

is selected) or the current time

•

: The alarm codes

• : The message of error

• : Programme is completed.

E. : The door locked indicator

• You cannot open the appliance door when

the symbol is on.

• You can open the door only when the

symbol goes off.

: The Finish At indicator ( םייס -ב )

G. : The indicator of the child lock

PROGRAMME CHART

Programme

Temperature range

Maximum load

Reference spin

speed

Programme description

(Type of load and soil level)

30' @ 30°

30°C

3 kg

800 rpm

A short cycle for synthetic and delicate items with

light soil level or for items to freshen up.

הנתוכ

90°C - Cold

8 kg

1400 rpm

White cotton and coloured cotton. Normal and heavy

soil.

1) Visible only for 2 seconds when you activate the appliance.

Programme

Temperature range

Maximum load

Reference spin

speed

Programme description

(Type of load and soil level)

הנתוכ ינוכסח

60°C - 40°C

8 kg

1400 rpm

White cotton and fast-coloured cotton. Normal soil.

The energy consumption decreases and the time of the

washing programme is extended, ensuring good washing

results.

יטטניס

60°C - Cold

3 kg

1200 rpm

Synthetic items or mixed fabric items. Normal soil.

םינידע

40°C - Cold

3 kg

1200 rpm

Delicate fabrics such as acrylics, viscose and mixed

fabrics requiring gentler washing. Normal soil.

רמצ/הסיבכ דיב

40°C - Cold

1,5 kg

1200 rpm

Machine washable wool, hand washable wool and

other fabrics with «hand washing» care symbol

ןונעיר 20 תוקד

40°C - 30°C

1 kg

1200 rpm

A very short cycle for cotton and synthetic items with

light soil level or worn only once.

םידב םיברועמ

60°C - Cold

2 kg

1200 rpm

Special programme for cotton, synthetic and mixed

fabrics with light soil. In case of setting cold wash cycle

make sure to use the detergent designed for low tempera-

tures.

1) Standard programmes for the Energy Label consumption values. According to regulation

1061/2010, these programmes are respectively the «Standard 60°C cotton programme» and the «Stand-

ard 40°C cotton programme». They are the most efficient programmes in terms of combined energy and

water consumption for washing normally soiled cotton laundry.

The water temperature of the washing phase may differ from the temperature declared for the

selected programme.

2) During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't

rotate or doesn't rotate properly, but this is normal for this programme.

Programme options compatibility

Programme

תינכות תרצוקמ

הפיטש תרבגומ

ץוהיג לק

הפיטש דבלב

הטיחס זוקינו

30' @ 30° ■ ■ ■ ■ ■

הנתוכ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

הנתוכ ינוכסח ■ ■ ■ ■ ■ ■ ■ ■ ■

יטטניס ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

םינידע ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

Programme

תינכות תרצוקמ

הפיטש תרבגומ

ץוהיג לק

הפיטש דבלב

הטיחס זוקינו

רמצ/הסיבכ דיב ■ ■ ■ ■ ■ ■ ■

ןונעיר 20

תוקד

■ ■ ■ ■ ■ ■

םידב םיברועמ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

1) When you set this option, we recommend that you decrease the quantity of the laundry. It is possible to

keep the full load but the washing results can be unsatisfactory. Recommended load: cotton: 4 kg, syn-

thetics and delicates: 1,5 kg.

CONSUMPTION VALUES

Stated values are obtained in laboratory conditions with relevant standards. Different cau-

ses can change the data: the quantity and type of laundry and ambient temperature. Wa-

ter pressure, the supply voltage and the temperature of inlet water may also affect the

washing programme duration.

Technical specifications may be changed without prior notice to improve the quality of

product.

At the start of the programme, the display shows the programme duration for the maxi-

mum load capacity.

During the washing phase the programme duration is automatically calculated and can be

greatly reduced if the laundry load is lower than the maximum load capacity (e.g. Cotton

60°C, maximum load capacity 8 kg, the programme duration exceeds 2 hours; actual load

1 kg, the programme duration will be less than 1 hour).

When the appliance is calculating the real programme duration a dot flashes in the dis-

play.

Programmes Load (kg)

Energy con-

sumption

(kWh)

Water con-

sumption (litre)

Approximate pro-

gramme duration (mi-

nutes)

Cottons 60°C 8 1,35 70 159

Cotton Energy Saving Pro-

gramme 60°C

8 0,96 52 244

Cottons 40°C 8 0,87 69 158

Programmes Load (kg)

Energy con-

sumption

(kWh)

Water con-

sumption (litre)

Approximate pro-

gramme duration (mi-

nutes)

Synthetics 40°C

3 0,60 56 103

Delicates 40°C 3 0,55 59 81

Wool/Handwash 30°C 1,5 0,45 62 75

1) «Cotton Energy Saving programme » at 60°C with a load of 8 kg is the reference programme for the

data entered in the energy label, in compliance with EU Commission Directive 95/12/EC and measured

according to EN 60456/2005.

Off Mode (W) Left On Mode (W)

0,48 0,48

The information given in the chart above is compliant with the EU Commission regulation 1015/2010

implementing directive 2009/125/EC .

OPTIONS

הרוטרפמט

With this option you can change the default

temperature.

Indicator

= cold water.

The indicator of the set temperature comes on.

הטיחס

With this option you can decrease the default spin

speed.

The display shows the indicator of the set speed.

Additional spin options:

No Spin

• Set this option to remove all spin phases.

• Set it for very delicate fabrics.

• The rinse phase uses more water for some

washing programmes.

• The display shows the indicator

Rinse Hold

• Set this option to prevent the laundry creases.

• The washing programme stops with the water in

the drum. The drum turns regularly to prevent

the laundry creases.

• The door stays locked. You must drain the water

to unlock the door.

• The display shows the indicator .

To drain the water refer to ‘At the end

of the programme’.

Extra Silent

• Set this option to remove all spin phases and to

perform a silent washing.

• The rinse phase uses more water for some

washing programmes.

• The washing programme stops with the water in

the drum. The drum turns regularly to prevent

the laundry creases.

• The door stays locked. You must drain the water

to unlock the door.

• The display shows the indicator .

To drain the water refer to ‘At the end

of the programme’.

תינכות תרצוקמ

With this option you can decrease the programme

duration.

Use this option for items with light soil or items to

refresh.

The related indicator comes on.

הפיטש תרבגומ

With this option you can wash very soiled laundry.

The washing cycle lasts longer with this option.

The related indicator comes on.

ץוהיג לק

The appliance carefully washes and spins the

laundry to prevent the creases.

The appliance decreases the spin speed, uses

more water and adapts the programme duration to

the type of laundry.

The related indicator comes on.

הפיטש דבלב

With this option you can perform only a last rinse of

a selected washing programme.

If you set also the Extra Rinse function ( ) the

appliance adds two or more rinses.

The related indicator comes on.

הטיחס זוקינו

With this option you can perform the spin and drain

cycle.

The spin phase is suitable to the washing

programme you set.

If you set also the No Spin option

( ) , the appliance only drains.

םייס -ב

With this option you can set the exact time in which

you would like your washing programme to be

completed.

The start of the washing programme delays. The

washing programme finishes in the set hour.

You can set the end time to 20 hours forward at

maximum.

The display shows the set hour of cycle's finish and

the indicator comes on.

EXTRA RINSE

With this option you can add some rinses to a

washing programme.

Use this option for persons allergic to detergents

and in areas where the water is soft.

The related indicator comes on.

SETTINGS

PERMANENT EXTRA RINSE

With this option you can permanently have an extra

rinse when you set a new programme.

• To activate/deactivate this option touch the

buttons and at the same time until the

indicator comes on/goes off.

CHILD LOCK

With this option you can prevent that the children

play with the control panel.

• To activate/deactivate this option, touch the

buttons and at the same time until the

indicator comes on/goes off.

Activate this option after you touch the button :

the buttons are locked (except for the button ) .

This option stays active even when you

switch off the appliance.

ACOUSTIC SIGNALS

The acoustic signals operate when:

• The programme is completed.

• The appliance has a malfunction.

To deactivate/activate the acoustic signals,

touch the buttons

and at the same time for 4

seconds.

If you deactivate the acoustic signals,

they continue operate when the

appliance has a malfunction.

BEFORE FIRST USE

WARNING! Refer to Safety chapters.

1) See in "Settings" how to activate this option.

BEFORE FIRST USE

During installation or before first use

you may observe some water in the

appliance. This is residual water left in

the appliance after a full functional test

in the factory to ensure the appliance

is delivered to customers in perfect

working order and is no cause for

concern.

1. Connect the mains plug to the mains socket.

2. Open the water tap.

3. Put a small quantity of detergent in the

compartment for washing phase.

4. Set and start a programme for cotton at the

highest temperature without laundry.

This removes all possible dirt from the drum and the

tub.

CLOCK SETTING

1. Touch the button and the button at the

same time for some seconds.

The hour digits flash.

2. Touch the button to change (or confirm) the

hour. The hours change with the steps of one

hour.

If you keep the button pressed

the digits change in a quicker way.

3. Touch the button to confirm the selection.

The minute digits flash.

4. Touch the button to change (or confirm) the

minutes. The minutes change with the steps of

one minute.

5. Touch the button to confirm the selection.

The appliance enters automatically in

clock setting mode when:

• you activate the appliance for the first time after

the installation,

• you activate the appliance for the first time after

it has been unplugged for more than two weeks,

• you did not confirm the time selection within 15

seconds period from last button touching,

• you switched the appliance off before

confirming the time.

DAILY USE

WARNING! Refer to Safety chapters.

LOADING THE LAUNDRY

Open the water tap. Connect the mains plug to the

mains socket.

1. Pull the door handle to open the appliance

door.

2. Put the laundry in the drum, one item at a time.

3. Shake the items before you put them in the

appliance.

Make sure not to put too much laundry in the drum.

Refer to max. loads indicated in "Programme chart".

4. Close the door.

CAUTION! Make sure that no laundry

stays between the seal and the door.

There is a risk of water leakage or

damage to the laundry.

Washing heavily oiled, greasy stains

could cause damage rubber parts of

the washing machine.

USING DETERGENT AND ADDITIVES

1. Measure out the de-

tergent and the fabric

conditioner.

2. Put the detergent

and the fabric condi-

tioner into the com-

partments.

3. Carefully close the

detergent drawer.

DETERGENT COMPARTMENTS

Detergent compartment for

washing phase.

If you use liquid detergent, put it

immediately before you start the

programme.

Compartment for liquid additives

(fabric conditioner, starch).

CAUTION! Do not

exceed the MAX

level.

Flap for powder or liquid deter-

gent.

LIQUID OR POWDER DETERGENT

The default position of

the flap is A (powder de-

tergent).

To use liquid detergent:

1. Remove the drawer.

Push the drawer edge in

the place with the arrow

(PUSH) to remove the

drawer easily.

2. Adjust the flap in posi-

tion B.

3. Put back the drawer in

the recess.

When you use the liquid detergent:

• Do not use gelatinous or thick liq-

uid detergents.

• Do not put more liquid then 120

ml.

• Do not set the delay start.

When the flap is in posi-

tion B and you want to

use powder detergent:

1. Remove the drawer.

2. Adjust the flap in po-

sition A.

3. Put back the drawer

in the recess.

• Measure out the detergent and the fabric condi-

tioner.

• Put the detergent and the fabric conditioner into

the compartments.

• Carefully close the detergent drawer.

ACTIVATING THE APPLIANCE

Press and hold the button to activate or

deactivate the appliance.

A tune sounds when the appliance is activated.

SETTING A PROGRAMME

1. Touch the programme button and set the

programme:

• The indicator of the button flashes.

• The display shows the programme duration.

2. If necessary, change the temperature and the

spin speed or add available options. When you

activate an option, the indicator of the set

option comes on.

If you set something incorrect, the

display shows the message .

STARTING A PROGRAMME WITHOUT THE

םייס -ב OPTION

Touch the button .

• The indicator of the button stops to

flash and stays on.

• The programme starts, the door locks, the

indicator is on.

• The drain pump can operate for a short time

at the beginning of the washing cycle.

After approximately 15 minutes from

the start of the programme:

• The appliance adjusts automatically

the programme duration agree with

the laundry load.

• The display shows the new value.

STARTING A PROGRAMME WITH THE םייס -ב

OPTION

Check if the appliance has the correct hour set.

See in "Clock setting" how to set the appliances's

clock.

First set the programme (and add options) then set

the option .

1. Touch the button to set the desired end

time. With the first touch the time is rounded to

the nearest hour or to the nearest half an hour.

By each next touch the end time increases by

30 minutes segments until maximum range of

20 hours.

The display shows the finish hour you set (e.g.

) and the indicator is on to show that

this option is active.

2. Touch the button :

• The door is locked.

• The appliance starts the countdown.

• When the countdown is completed, the

programme starts automatically and the

actual programme duration counts down in

minutes until the cycle end.

You can cancel or change the set of

the option before you touch the

button . After touching the button

you can only cancel the option .

To cancel the םייס -ב option:

a. Touch the button

to set the appliance

to pause. The indicator of button

flashes.

b. Touch the button again and again until

the indicator goes off from the display.

Touch the button again to start the

programme immediately.

INTERRUPTING A PROGRAMME AND

CHANGING THE OPTIONS

You can change only some options before they

operate.

1. Touch .

The indicator of this button flashes.

2. Change the options.

If you change any option the

option (if set) will be disabled.

3. Touch again.

The programme continues.

CANCELLING A PROGRAMME

1. Press the button for some seconds to

cancel the programme and to deactivate the

appliance.

2. Press the same button again to activate the

appliance. Now, you can set a new washing

programme.

Before starting the new programme

the appliance could drain the water. In

this case, make sure that the detergent

is still in the detergent compartment, if

not fill the detergent again.

OPENING THE DOOR

While a programme (or the ) operates, the

appliance door is locked. The indicator is on.

CAUTION! If the temperature and

level of the water in the drum are too

high, you cannot open the door.

To open the door during the first minutes of

the cycle (or when the operates) :

1. Touch the button to pause the appliance.

2. Wait until the indicator goes off.

1) If you keep the button

pressed the digits change in a quicker way.

3. You can open the door.

4. Close the door and touch the button again.

The programme (or the ) continues.

AT THE END OF THE PROGRAMME

• The appliance stops automatically.

• The acoustic signal operates (if it is activated).

• In the display comes on.

• The indicator of the button goes off.

• The door lock indicator goes off.

• You can open the door.

• Remove the laundry from the appliance. Make

sure that the drum is empty.

• Press the button for some seconds to

deactivate the appliance.

• Close the water tap.

• Keep the door and the detergent drawer ajar, to

prevent the mildew and odours.

The washing programme is completed, but

there is water in the drum:

• The drum turns regularly to prevent the creases

in the laundry.

• The indicator flashes to remind you to drain

the water.

• The door lock indicator

is on. The indicator

of button flashes. The door stays locked.

• You must drain the water to open the door.

Draining the water:

1. To drain the water.

• Touch the button . The appliance

drains the water and spins with the

maximum spin speed for selected washing

programme.

• Alternatively, touch the button

to change

the spin speed and then touch the button

. The appliance drains the water and

spins. If you set , the appliance only

drains.

2. When the programme is completed and the

door lock indicator goes off, you can open

the door.

3. Press the button for some seconds to

deactivate the appliance.

The appliance drains and spins

automatically after approximately 18

hours (except for Wool programme).

AUTO-OFF OPTION

The AUTO-OFF stand-by option automatically

deactivates the appliance to decrease the energy

consumption. All the indicators and the display go

off when :

• You do not use the appliance for 5 minutes

before you touch .

Press the button to activate the appliance

again.

• After 5 minutes from the end of the washing

programme.

Press the button to activate the appliance

again.

The display shows the end of the last set

programme.

Touch the button

if you want to set a new

cycle.

HINTS AND TIPS

THE LAUNDRY LOAD

• Divide the laundry in: white, coloured,

synthetics, delicates and wool.

• Obey the washing instructions that are on the

laundry care labels.

• Do not wash white and coloured items together.

• Some coloured items can discolour with the first

wash. We recommend that you wash them

separately for the first times.

• Turn multilayered fabrics, wool and items with

painted illustrations inside out.

• Remove hard stains with a special detergent.

• Wash and pre-treat heavy soil stains before

putting items in drum

• Be careful with the curtains. Remove the hooks

and put the curtains in a washing bag or

pillowcase.

• Do not wash laundry without hems or with cuts.

Use a washing bag to wash small and/or

delicate items (e.g. underwired bras, belts,

tights, shoelaces, ribbons, etc. ).

• A very small load can cause balance problems

with the spin phase. If this occurs, adjust

manually the items in the tub and start the spin

phase again.

• Avoid washing garments full of long animal hair

or poor quality garments releasing lots of fluff

that could block the drain circuit and therefore

requiring the Service assistance.

• Button up pillowcases, close zippers, hooks and

poppers. Tie up belts, cords, shoelaces, ribbons

and any other loose elements.

• Empty the pockets and unfold the items.

STUBBORN STAINS

For some stains, water and detergent is not

sufficient.

We recommend that you pre-treat these stains

before you put the items in the appliance.

Special stain removers are available. Use the

special stain remover that is applicable to the type

of stain and fabric.

DETERGENTS AND ADDITIVES

• Only use detergents and additives specially

made for washing machines:

– powder detergents for all types of fabric,

– powder detergents for delicate fabrics (40

°C max) and woollens,

– liquid detergents, preferably for low

temperature wash programmes (60 °C max)

for all types of fabric, or special for woollens

only.

• Do not mix different types of detergents.

• To help the environment, do not use more than

the correct quantity of detergent.

• Obey the instructions that you find on the on

packaging of these products.

• Use the correct products for the type and colour

of the fabric, the programme temperature and

the level of soil.

• If your appliance does not have the detergent

dispenser with the flap device, add the liquid

detergents with a dosing ball (supplied by the

detergent's manufacturer).

ECOLOGICAL HINTS

• Always start a washing programme with the

maximum load of laundry allowed.

• If necessary, use a stain remover when you set a

programme with a low temperature.

• To use the correct quantity of detergent, check

the water hardness of your domestic system.

Refer to "Water hardness".

WATER HARDNESS

If the water hardness in your area is high or

moderate, we recommend that you use a water

softener for washing machines. In areas where the

water hardness is soft it is not necessary to use a

water softener.

To know the water hardness in your area, contact

your local water authority.

Use the correct quantity of the water softener.

Obey the instructions that you find on the

packaging of the product.

CARE AND CLEANING

WARNING! Refer to Safety chapters.

The appliance is intended for normal

household use only.

Read the chapter carefully for best

maintenance and care.

EXTERNAL CLEANING

Clean the appliance with soap and warm water

only. Fully dry all the surfaces.

CAUTION! Do not use alcohol,

solvents or chemical products.

DESCALING

If the water hardness in your area is high or

moderate, we recommend that you use a water

descaling product for washing machines.

Regularly examine the drum to prevent limescale

and rust particles.

To remove rust particles use only special products

for washing machines. Do this separately from the

laundry wash.

Always obey the instructions that you

find on the packaging of the product.

MAINTENANCE WASH

With the low temperature programmes it is possible

that some detergent stays in the drum. Perform a

maintenance wash regularly. To do this:

• Remove all laundry from the drum.

• Select the cotton programme with the highest

temperature with a small quantity of detergent.

DOOR SEAL

This appliance is designed with a self cleaning

draining system, allowing light fluff fibers that fall

off the clothes to be drained out with the water, in

such a way that there is no need to access this

area for regular maintenance and cleaning.

Regularly examine the seal and remove all objects

from the inner part. Coins, buttons, other small

items forgotten in the pockets of your clothes are

deposited during the washing cycle in the special

double lip trap in the porthole seal, where they can

be conveniently recovered at the end of the cycle.

CLEANING THE DETERGENT DISPENSER

1 2 3 4

5 6

CLEANING THE INLET HOSE AND THE VALVE FILTER

1 2 3

45°

20°

FROST PRECAUTIONS

If the appliance is installed in an area where the

temperature can be less than 0 °C, remove the

remaining water from the inlet hose and the drain

pump.

Do this procedure also when you want

to do the emergency drain.

1. Disconnect the mains plug from the mains

socket.

2. Remove the water inlet hose.

3. Remove the drain hose from the rear support

and unhook it from sink or spigot.

4. Put the ends of the drain and inlet hose in a

container. Let the water flow out of the hoses.

5. Set any selected programme with option

הטיחס

זוקינו and let it operate until the end of the cycle.

6. When no more water flows, install the inlet

hose and the drain hose again.

7. Press the button to deactivate the

appliance.

WARNING! Make sure that the

temperature is more than 0°C before

you use the appliance again. The

manufacturer is not responsible for

damages caused by low temperatures.

TROUBLESHOOTING

WARNING! Refer to Safety chapters.

INTRODUCTION

The appliance does not start or it stops during

operation.

First try to find a solution to the problem (refer to

the table). If the problem persists, contact the

Authorised Service Centre.

With some problems, the acoustic signals

operate and the display shows an alarm

code:

•

- The appliance does not fill with water

properly. Start the appliance again by pressing

לחתה/ההשה button. After 10 seconds the door will

be unlocked.

• - The appliance does not drain the water.

• - The appliance door is open or not

closed correctly. Please check the door!

If the appliance is overloaded,

remove some items from the drum

and/or keep pressed the door and

push the לחתה/ההשה button at the

same time until the indicator

stops flashing (see the picture

below).

• - The mains supply is unstable. Wait until

the mains supply is stable.

• - No communication between electronic

elements of the appliance. Switch off and

switch on again. The programme was not

finished properly or the appliance stopped too

early. If the alarm code appears again, contact

the Authorised Service Centre.

WARNING! Deactivate the appliance

before you do the checks.

POSSIBLE FAILURES

Problem Possible solution

The programme does not

start.

• Make sure that the mains plug is connected to the mains socket.

• Make sure that the appliance door is closed.

• Make sure that there is not a damaged fuse in the fuse box.

• Make sure that the Start/Pause has been pressed.

• If the delay start is set, cancel the setting or wait for the end of

countdown.

• Deactivate the Child Lock function if it is on.

The appliance does not fill

with water properly.

• Make sure that the water tap is open.

• Make sure that the pressure of the water supply is not too low. For

this information, contact your local water authority.

• Make sure that the water tap is not clogged.

• This problem may be caused by the filter of the inlet hose or the

valve drain filter which may be clogged. Refer to “Care and clean-

ing”. If problem remains please contact the Authorised Service

Centre.

• Make sure that the inlet hose has no kinks or bends.

• Make sure that the connection of the water inlet hose is correct.

The appliance does not

drain the water.

• Make sure that the sink spigot is not clogged.

• Make sure that the drain hose has no kinks or bends.

• Make sure that the connection of the drain hose is correct.

• Set the drain option if you set a programme without drain phase.

• Set the drain option if you set an option which ends with water in

the drum.

• This problem may be caused by the clogged drain filter. Please

contact the Authorised Service Centre.

The spin phase does not

operate or the washing cy-

cle lasts longer than usual-

ly.

• Adjust manually the items in the tub and start the spin phase again.

This problem may be caused by balance problems.

• Set the spin option.

• Set the drain option if you set an option which ends with water in

the drum.

• This problem may be caused by the clogged drain filter. Please

contact the Authorised Service Centre.

There is water on the floor. • Make sure that the couplings of the water hoses are tight and there

is not water leakages.

• Make sure that the water inlet hose and the drain hose have no

damages.

• Make sure you use the correct detergent and the correct quantity of

it.

You cannot open the appli-

ance door.

• Make sure that the washing programme is finished.

• Set the drain or the spin option if there is water in the drum.

• Do the emergency drain procedure. See "Frost precautions" (in

"Care and Cleaning" chapter).

The appliance makes an

unusual noise.

• Make sure the levelling of the appliance is correct. Refer to 'Installa-

tion instruction'.

• Make sure that the packaging and/or the transit bolts are removed.

Refer to 'Installation instruction'.

• Add more laundry in the drum. The load may be too small.

Problem Possible solution

The appliance fills with wa-

ter and drain immediately.

• Make sure that the drain hose is in the correct position. The end of

the hose may be too low. Refer to 'Installation instruction'.

The cycle is shorter than

the time displayed.

• The appliance calculates a new time according to the laundry load.

See the ‘Consumption Values’ chapter.

The cycle is longer than

the time displayed.

• An unbalanced laundry load increases the duration time. This is a

normal behaviour of the appliance.

The washing results are

not satisfactory.

• Increase the detergent quantity or use a different detergent.

• Use special products to remove the stubborn stains before you

wash the laundry.

• Make sure that you set the correct temperature.

• Decrease the laundry load.

You cannot set an option. • Make sure that you press only the wanted touch button(s).

After the check, activate the appliance. The

programme continues from the point of interruption.

If the problem occurs again, contact the Authorised

Service Centre.

If the display shows other alarm codes. Deactivate

and activate the appliance. If the problem

continues, contact the Authorised Service Centre.

SERVICE

We recommend the use of original spare parts.

When contacting the Authorised Service Centre,

make sure that these data are available. You can

find the information on the rating plate: model, PNC

and Serial Number. (Mod., Prod. No., Ser. No.)

TECHNICAL DATA

Dimension Width/ Height/ Depth/ To-

tal depth

600 mm/ 850 mm/ 520 mm/ 576 mm

Electrical connection Voltage

Overall power

Fuse

Frequency

230 V

2200 W

10 A

50 Hz

Level of protection against ingress of solid particles and

moisture ensured by the protective cover, except where

the low voltage equipment has no protection against

moisture

IPX4

Water supply pressure Minimum

Maximum

0.5 bar (0.05 MPa)

8 bar (0.8 MPa)

Water supply

1) Cold water

Maximum Load Cotton 8 kg

Energy Efficiency Class A+++

Spin Speed Maximum spin speed 1351 rpm

1) Connect the water inlet hose to a water tap with a 3/4'' thread.

La page charge ...

Zanussi ZWF81467I Manuel utilisateur

Marque: Zanussi

Modèle: ZWF81467I

Catégorie: Machines à laver

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Zanussi ZWF81467I User manual

Zanussi ZWF81467I Manuel utilisateur

Zanussi ZWF81467I Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents