Porter-Cable 90550119 Manuel utilisateur

Marque: Porter-Cable

Modèle: 90550119

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Ce manuel convient également à

VS Orbital Cordless

Jig Saw

www.portercable.com

INSTRUCTIVO DE OPERACIÓN,

CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA.

ADVERTENCIA: LÉASE ESTE

INSTRUCTIVO ANTES DE USAR EL

PRODUCTO.

CATALOG NUMBER

PC1800JS

Scie sauteuse orbitale sans

fil à vitesse variable

Sierra caladora inalámbrica de acción

orbital y velocidad variable

Instruction manual

Manuel d'instructions

Manual de'instrucciones

Batteries and chargers sold separately

90550119 PC1800JS Jig Saw 4/9/09 7:52 AM Page 1

General Power Tool Safety Warnings

WARNING! Read all safety warnings and instructions. Failure to follow

the warnings and instructions may result in electric shock, fire and/or serious

injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded)

power tool or battery-operated (cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the

presence of flammable liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug in any way.

Do not use any adapter plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes,

radiators, ranges and refrigerators. There is an increased risk of electric shock

if your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power

tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or

unplugging the power tool. Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for

outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric

shock.

f) If operating a power tool in a damp location is unavoidable, use a ground

fault circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the

risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired or

under the influence of drugs, alcohol or medication. A moment of inattention

while operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective

equipment such as dust mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off-position

before connecting to power source and/or battery pack, picking up or

carrying the tool. Carrying power tools with your finger on the switch or

energising power tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A

wrench or a key left attached to a rotating part of the power tool may result in

personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This

enables better control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,

clothing and gloves away from moving parts. Loose clothes, jewellery or long

hair can be caught in moving parts.

g) If devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used. Use of dust

collection can reduce dust-related hazards.

90550119 PC1800JS Jig Saw 4/9/09 7:52 AM Page 2

4) Power tool use and care

a) Do not force the power tool. Use the correct power tool for your application.

The correct power tool will do the job better and safer at the rate for which it was

designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power

tool that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the

power tool before making any adjustments, changing accessories, or storing

power tools. Such preventive safety measures reduce the risk of starting the

power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power

tool. Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired before use. Many

accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in accordance with these

instructions, taking into account the working conditions and the work to be

performed. Use of the power tool for operations different from those intended

could result in a hazardous situation.

5) Battery tool use and care

a) Recharge only with the charger specified by the manufacturer. A charger that

is suitable for one type of battery pack may create a risk of fire when used with

another battery pack.

b) Use power tools only with specifically designated battery packs. Use of any

other battery packs may create a risk of injury and fire.

c) When battery pack is not in use, keep it away from other metal objects like

paper clips, coins, keys, nails, screws, or other small metal objects that can

make a connection from one terminal to another. Shorting the battery terminals

together may cause burns or a fire.

d) Under abusive conditions, liquid may be ejected from the battery, avoid

contact. If contact accidentally occurs, flush with water. If liquid contacts

eyes, additionally seek medical help. Liquid ejected from the battery may cause

irritation or burns.

6) Service

a) Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

SPECIFIC SAFETY RULES

• Hold power tools by insulated gripping surfaces when performing an operation

where the cutting tool may contact hidden wiring or its own cord. Contact with a

"live" wire will make exposed metal parts of the tool "live" and shock the operator.

• When working on a ladder or on scaffolding be sure to lay the tool down on its

side when not in use. Some tools with large battery packs will stand upright but may be

easily knocked over.

• Use clamps or another practical way to secure and support the work piece to a

stable platform. Holding the work by hand or against your body leaves it unstable and

may lead to loss of control.

• Keep hands away from cutting area. Never reach underneath the material for any

reason. Hold front of saw by grasping the contoured gripping area. Do not insert fingers

or thumb into the vicinity of the reciprocating blade and blade clamp. Do not stabilize the

saw by gripping the shoe.

• Keep blades sharp. Dull blades may cause the saw to swerve or stall under

pressure.

• When cutting pipe or conduit ensure that they are free from water, electrical wiring,

etc.

90550119 PC1800JS Jig Saw 4/9/09 7:52 AM Page 3

• Allow the motor to come to a complete stop before withdrawing the blade from the

kerf (the slot created by cutting). A moving blade may impact the workpiece causing a

broken blade, workpiece damage or loss of control and possible personal injury.

• Never hold work in your hand, lap or against parts of your body when sawing. The

saw may slip and the blade could contact the body causing injury.

• Keep handles dry, clean, free from oil and grease. This will enable better control of the

tool.

• Clean out your tool often, especially after heavy use. Dust and grit containing metal

particles often accumulate on interior surfaces and could create an electric shock hazard.

• Do not operate this tool for long periods of time. Vibration caused by the operating

action of this tool may cause permanent injury to fingers, hands, and arms. Use gloves to

provide extra cushion, take frequent rest periods, and limit daily time of use.

ALWAYS use safety glasses. Everyday eyeglasses are NOT safety

glasses. Also use face or dust mask if drilling operation is dusty. ALWAYS WEAR

CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CPA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NOSH/OSHA respiratory protection.

Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities contains chemicals known to the state of California to

cause cancer, birth defects or other reproductive harm. Some examples of these

chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work.

To reduce your exposure to these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are specially designed to filter

out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,

and other construction activities. Wear protective clothing and wash exposed

areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the

skin may promote absorption of harmful chemicals.

Use of this tool can generate and/or disperse dust, which may cause

serious and permanent respiratory or other injury. Always use NOSH/OSHA

approved respiratory protection appropriate for the dust exposure. Direct particles away

from face and body.

Wear appropriate hearing protection during use. Under some

conditions and duration of use, noise from this product may contribute to hearing loss.

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual. The information it contains

relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols

below are used to help you recognize this information.

Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

Used without the safety alert symbol indicates a potentially hazardous

situation which, if not avoided, may result in property damage.

90550119 PC1800JS Jig Saw 4/9/09 7:52 AM Page 4

• When using an extension cord, be sure to use one heavy enough to carry the current

your product will draw. An undersized cord will cause a drop in line voltage resulting in

loss of power and overheating. The following table shows the correct size to use

depending on cord length and nameplate ampere rating. If in doubt, use the next

heavier gage. The smaller the gage number, the heavier the cord.

Symbols

• The label on your tool may include the following symbols. The symbols and their

definitions are as follows:

V..................volts A ..................amperes

Hz................hertz W..................watts

min ..............minutes ................alternating current

............direct current

o ................no load speed

................Class I Construction ..................earthing terminal

(grounded) ................safety alert symbol

................Class II Construction .../min or rpm...revolutions or

(double insulated) reciprocation per minute

sfpm ............surface feet per minute

LI-ION Battery Packs and Chargers

Battery: LI-ION 18V

Charger: LI-ION

PC18BL

PC18BLX

PC18BLEX

PCLMVC

PCXMVC

Description Cat. #

NI-CD Battery Packs and Chargers

This product can accept any of the batteries and chargers listed in the chart below.

Battery: NI-CD 18V

Charger: NI-CD

PC18B

PCMVC

PCXMVC

Description Cat. #

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150

(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)

240V 0-50 51-100 101-200 201-300

(0-15,2m) (15,2-30,4m) (30,4-60,9m) (60,9-91,4m)

Ampere Rating

More Not more American Wire Gage

Than Than

0-6 18 16 16 14

6 - 10 18 16 14 12

10 - 12 16 16 14 12

12 - 16 14 12 Not Recommended

90550119 PC1800JS Jig Saw 4/9/09 7:52 AM Page 5

IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CHARGERS

SAVE THESE INSTRUCTIONS: This manual contains important safety instructions for

battery chargers.

• Before using charger, read all instructions and cautionary markings on charger, battery

pack, and product using battery pack.

Shock hazard. Do not allow any liquid to get inside charger.

Burn hazard. To reduce the risk of injury, charge only designated

PORTER-CABLE batteries. Other types of batteries may burst causing personal injury

and damage.

Under certain conditions, with the charger plugged in to the power

supply, the charger can be shorted by foreign material. Foreign materials of a

conductive nature such as, but not limited to, steel wool, aluminum foil, or any buildup

of metallic particles should be kept away from charger cavities. Always unplug the

charger from the power supply when there is no battery pack in the cavity. Unplug

charger before attempting to clean.

• DO NOT attempt to charge the battery pack with any chargers other than the

ones in this manual. The charger and battery pack are specifically designed to

work together.

• These chargers are not intended for any uses other than charging designated

PORTER-CABLE rechargeable batteries. Any other uses may result in risk of fire,

electric shock or electrocution.

• Do not expose charger to rain or snow.

• Pull by plug rather than cord when disconnecting charger. This will reduce risk

of damage to electric plug and cord.

• Make sure that cord is located so that it will not be stepped on, tripped over,

or otherwise subjected to damage or stress.

• Do not use an extension cord unless it is absolutely necessary. Use of improper

extension cord could result in risk of fire, electric shock, or electrocution.

• An extension cord must have adequate wire size (AWG or American Wire

Gauge) for safety. The smaller the gauge number of the wire, the greater the

capacity of the cable, that is 16 gauge has more capacity than 18 gauge. When

using more than one extension to make up the total length, be sure each individual

extension contains at least the minimum wire size.

• Do not place any object on top of charger or place the charger on a soft

surface that might block the ventilation slots and result in excessive internal

FUNCTIONAL DESCRIPTION

1. Variable speed switch

2. Lock-off button

3. Saw blade locking lever

4. Saw blade support roller

5. Shoe plate

6. Shoe plate locking knob

7. Cutting action lever

8. Dust extraction adaptor

90550119 PC1800JS Jig Saw 4/9/09 7:52 AM Page 6

heat. Place the charger in a position away from any heat source. The charger is

ventilated through slots in the top and the bottom of the housing.

• Do not mount charger on wall or permanently affix charger to any surface. The

charger is intended to use on a flat, stable surface (i.e., table top, bench top).

• Do not operate charger with damaged cord or plug — have them replaced

immediately.

• Do not operate charger if it has received a sharp blow, been dropped, or

otherwise damaged in any way. Take it to an authorized service center.

• Do not disassemble charger; take it to an authorized service center when service

or repair is required. Incorrect reassembly may result in a risk of electric shock,

electrocution or fire.

• Disconnect the charger from the outlet before attempting any cleaning. This

will reduce the risk of electric shock. Removing the battery pack will not reduce this

risk.

• NEVER attempt to connect 2 chargers together.

• The charger is designed to operate on standard household electrical power

(120 Volts). Do not attempt to use it on any other voltage.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTION FOR BATTERY PACKS

For safe operation, read this manual and manuals originally supplied

with tool before using the charger.

The battery pack is not fully charged out of the carton. Before using the battery pack

and charger, read the safety instructions below. Then follow charging procedures

outlined.

READ ALL INSTRUCTIONS

• Do not incinerate the battery pack even if it is severely damaged or is

completely worn out. The battery pack can explode in a fire. Toxic fumes and

materials are created when LI-ION battery packs are burned.

• Do not charge or use battery in explosive atmospheres, such as in the presence

of flammable liquids, gases or dust. Inserting or removing the battery from the

charger may ignite the dust or fumes.

• If battery contents come into contact with the skin, immediately wash area with

mild soap and water. If battery liquid gets into the eye, rinse water over the open eye

for 15 minutes or until irritation ceases. If medical attention is needed, the battery

electrolyte for LI-ION batteries is composed of a mixture of liquid organic carbonates

and lithium salts. For NI-Cd batteries it is a 25-35% solution of potassium hydroxide.

• Contents of opened battery cells may cause respiratory irritation. Provide fresh

air. If symptoms persists, seek medical attention.

Burn hazard. Battery liquid may be flammable if exposed to spark or

flame.

• Charge the battery packs only in PORTER-CABLE chargers.

• DO NOT splash or immerse in water or other liquids. This may cause premature

cell failure.

• Do not store or use the tool and battery pack in locations where the

temperature may reach or exceed 105°F (40˚C) (such as outside sheds or metal

buildings in summer).

Never attempt to open the battery pack for any reason. If battery pack

case is cracked or damaged, do not insert into charger. Do not crush, drop or damage

battery pack. Do not use a battery pack or charger that has received a sharp blow, been

dropped, run over or damaged in any way (i.e., pierced with a nail, hit with a hammer,

stepped on). Damaged battery packs should be returned to service center for recycling.

90550119 PC1800JS Jig Saw 4/9/09 7:52 AM Page 7

BATTERY CAP INFORMATION

Battery storage and carrying caps are provided for use whenever the

battery is out of the tool or charger. Remove cap before placing battery in

charger or tool.

Fire hazard. Do not store or carry battery so that metal objects can

contact exposed battery terminals. For example, do not place battery in aprons,

pockets, tool boxes, product kit boxes, drawers, etc., with loose nails, screws, keys, etc.

Transporting batteries can possibly cause fires if the battery terminals

inadvertently come in contact with conductive materials such as keys, coins, hand

tools and the like. The US Department of Transportation Hazardous Material

Regulations (HMR) actually prohibit transporting batteries in commerce or on airplanes

(i.e., packed in suitcases and carry-on luggage) UNLESS they are properly protected

from short circuits. So when transporting individual batteries, make sure that the battery

terminals are protected and well insulated from materials that could contact them and

cause a short circuit. NOTE: LI-ION batteries should not be put in checked baggage.

STORAGE RECOMMENDATIONS

1. The best storage place is one that is cool and dry away from direct sunlight and

excess heat or cold.

2. Long storage will not harm the battery pack or charger. Under proper conditions

LI-ION batteries, can be stored for 5 years or more.

CHARGING PROCEDURE

PORTER-CABLE chargers are designed to charge PORTER-CABLE battery packs in

30-60 minutes depending on the pack being charged.

1. Plug the charger into an appropriate outlet before inserting the battery pack.

2. Insert the battery pack into the charger (figure B).

3. The LED will flash indicating that the battery is being charged.

4. The completion of charge is indicated by the LED remaining on continuously.

The pack is fully charged and may be used at this time or left on the charger.

CHARGER DIAGNOSTICS

This charger is designed to detect certain problems that can arise with the battery

packs or the power source. Problems are indicated by one LED flashing in different

patterns.

BAD BATTERY

The charger can detect a weak or damaged battery. The LED flashes in the

pattern indicated on the label. If you see this bad battery blink pattern, do not

continue to charge the battery. Return it to a service center or a collection site

for recycling.

HOT/COLD PACK DELAY

When the charger detects a battery that is excessively hot or excessively cold, it

automatically starts a Hot/Cold Pack Delay, suspending charging until the battery

has normalized. After this happens, the charger automatically switches to the

Pack Charging mode. This feature ensures maximum battery life. The light

flashes in the pattern indicated on the label.

Battery Cap

90550119 PC1800JS Jig Saw 4/9/09 7:52 AM Page 8

PROBLEM POWER LINE

When the charger is used with some portable power sources such as generators

or sources that convert DC to AC, the charger may temporarily suspend

operation. The LED flashes in the pattern indicated on the label. This indicates

that the power source is out of limits.

LEAVING THE BATTERY IN THE CHARGER

The charger and battery pack can be left connected with the LED glowing indefinitely.

The charger will keep the battery pack fresh and fully charged. This charger features

an automatic tune-up mode which equals or balances the individual cells in the battery pack

to allow it to function at peak capacity. Battery packs should be tuned up weekly or

whenever the battery no longer delivers the same amount of work. To use the automatic

tune-up mode, place the battery pack in the charger and leave it for at least 8 hours.

IMPORTANT CHARGING NOTES

1. Longest life and best performance can be obtained if the battery pack is charged

when the air temperature is between 65°F and 75°F (18°- 24°C). DO NOT charge the

battery pack in an air temperature below +40°F (+4.5°C), or above +105°F (+40.5°C).

This is important and will prevent serious damage to the battery pack.

2. The charger and battery pack may become warm to touch while charging. This is a

normal condition, and does not indicate a problem. To facilitate the cooling of the

battery pack after use, avoid placing the charger or battery pack in a warm

environment such as in a metal shed, or an uninsulated trailer.

3. If the battery pack does not charge properly:

a. Check current at receptacle by plugging in a lamp or other appliance

b. Check to see if receptacle is connected to a light switch which turns power off

when you turn out the lights.

c. Move charger and battery pack to a location where the surrounding air

temperature is approximately 65°F - 75°F (18°- 24°C).

d. If charging problems persist, take the tool, battery pack and charger to your

local service center.

4. The battery pack should be recharged when it fails to produce sufficient power on

jobs which were easily done previously. DO NOT CONTINUE to use under these

conditions. Follow the charging procedure. You may also charge a partially used pack

whenever you desire with no adverse affect on the battery pack.

5. Foreign materials of a conductive nature such as, but not limited to, steel wool,

aluminum foil, or any buildup of metallic particles should be kept away from charger

cavities. Always unplug the charger from the power supply when there is no battery

pack in the cavity. Unplug charger before attempting to clean.

6. Do not freeze or immerse charger in water or any other liquid.

Shock hazard. Do not allow any liquid to get inside charger.

Never attempt to open the battery pack for any reason. If the plastic

housing of the battery pack breaks or cracks, return to a service center for recycling.

INSTALLING AND REMOVING THE BATTERY PACK FROM THE TOOL

Make certain the lock-off button is engaged to prevent switch actuation

before removing or installing battery.

TO INSTALL BATTERY PACK: Insert battery pack

into tool as shown in figure C.

90550119 PC1800JS Jig Saw 4/9/09 7:52 AM Page 9

SAVE THESE INSTRUCTIONS

OPERATION

Before attempting any of the following operations, make sure that the

saw blade has stopped, and the battery is removed. Used saw blades can be hot.

Blade Installation (FIGURE E)

- Hold the saw blade with teeth facing forward.

- Holding the saw upside down, push the saw blade

locking lever (3) downward.

- Insert the shank of the saw blade into the blade

holder as far as it will go.

- Release the lever.

- Check to ensure blade is secure before cutting.

ADJUSTING THE SHOE PLATE FOR BEVEL

CUTS (FIGURE F)

Never use the tool when the shoe

plate (5) is loose or removed.

The shoe plate can be set to a left or right bevel

angle of up to 45°.

- Turn the locking knob (6) in direction A to release

the shoe plate (5).

- Pull the shoe plate (5) backwards and set it to the

required angle. You can use the scale or a protractor

to check the angle.

- Turn the locking knob (6) in direction B to lock the

shoe plate in place.

To reset the shoe plate for straight cuts:

- Turn the locking knob (6) in direction A to release the shoe plate (5).

- Pull the shoe plate backwards and set it to an angle of approximately 0.

- Push the shoe plate forward.

- Turn the locking knob (6) in direction B to lock the shoe plate in place. Make sure that

the shoe plate is supported by the guide ribs.

TO REMOVE BATTERY PACK: Depress the battery

release button as shown in figure D and pull battery

pack out of tool.

90550119 PC1800JS Jig Saw 4/9/09 7:52 AM Page 10

SWITCHING ON AND OFF

- To switch the tool on, depress the lock-off button (2) then press the variable speed

switch (1). The tool speed depends on how far you depress the switch.

- To switch the tool off, release the variable speed switch.

ORBITAL ACTION SELECTOR (FIGURE G)

- For fast, rough straight cuts in wood, set the orbital

action selector (7) to the symbol (II).

- For fast, smooth straight cuts in wood, set the orbital

action selector (7) to the symbol (I).

- For accurate, straight and curve cutting and a

smooth surface finish, set the orbital action selector

(7) to the symbol (0).

- NOTE: Orbital action is not recommended when

curve cutting or for use in metals.

CONNECTING A VACUUM CLEANER TO THE

TOOL (FIGURE H)

- Align the dust extraction adaptor (8) with the saw

shoe as shown.

- Insert the ribs (9) into the slots (10).

- Rotate the adaptor until it locks into position. Make

sure that the ribs (9) are correctly seated.

- Connect the vacuum cleaner hose (not supplied) to

the adaptor.

Dust extraction is not possible when making bevel

cuts.

Hints for optimum use

POCKET CUTTING

A pocket cut is an easy method of making an inside cut. The saw can be inserted directly

into a panel or board without first drilling a lead or pilot hole. In pocket cutting, measure the

surface to be cut and mark clearly with a pencil. Next tip the saw forward until the front end

of the shoe sits firmly on the work surface and the blade clears the work through its full

stroke. Switch the tool on and allow it to attain maximum speed. Grip the saw firmly and

lower the back edge of tool slowly until the blade reaches its complete depth. Hold the

shoe flat against the wood and begin cutting. Do not remove blade from cut while it is still

moving. Blade must come to a complete stop.

FLUSH CUTTING

A flush cut is necessary when finishing off cuts up to a wall or an obstacle, such as back-

splash. One of the easiest ways to accomplish the flush cut is to use a flush cutting

blade. The flush cutting blade provides the reach necessary to cut right up to the front

edge of the jig saw shoe. Return the shoe to the 0° positive stop position before installing

and using the flush cutting blade. For the best cut quality the flush cutting blade should

be used in the 0 or I orbital position. The flush cutting blade should not be used to start

the cut because the flush cutting blade prevents the shoe from being supported by the

work surface. Use wood cutting practices explained below.

WOOD CUTTING

Support the workpiece adequately at all times. Use a higher speed for cutting wood. Do

not attempt to turn the tool on when blade is against material to be cut. This could stall

the motor. Place the front of shoe on the material to be cut and hold the jig saw shoe

firmly against the wood while cutting. Don’t force the tool; let the blade cut at its own

speed. When the cut is complete, turn the jig saw off. Let blade come to a complete stop

and then lay the saw aside before loosening the work.

90550119 PC1800JS Jig Saw 4/9/09 7:52 AM Page 11

THE RBRC™ SEAL

The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the

LI-ION or NI-CD battery (or battery pack) indicates that the costs to recycle the

battery (or battery pack) at the end of its useful life have already been paid by

PORTER-CABLE.

RBRC™ in cooperation with PORTER-CABLE and other battery users, has

established programs in the United States to facilitate the collection of spent LI-

ION or NI-CD batteries. Help protect our environment and conserve natural resources by

returning the spent LI-ION or NI-CD battery to an authorized PORTER-CABLE service

center or to your local retailer for recycling. You may also contact your local recycling

center for information on where to drop off the spent battery.

RBRC™ is a registered trademark of the Rechargeable Battery Recycling Corporation.

MAINTENANCE

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the

tool; never immerse any part of the tool into a liquid.

REPLACEMENT PARTS

Use only identical replacement parts. For a parts list or to order parts, visit our service website at

www.portercable.com. You can also order parts from your nearest PORTER-CABLE Factory

Service Center or PORTER-CABLE Authorized Warranty Service Center. Or, you can call our

Customer Care Center at (888) 848-5175.

METAL CUTTING

In cutting thin gauge sheet metals, it is best to clamp wood to the bottom of sheet metal;

this will insure a clean cut without the risk of vibration or tearing of metal. Always remember

to use a finer blade for ferrous metals (for those that have a high iron content); and use a

coarser blade for non-ferrous metals (those that do not have an iron content). Use a high

speed setting for cutting soft metals (aluminum, copper, brass, mild steel, galvanized. pipe,

conduit sheet metal, etc.). Use lower speed to cut plastics, tile, laminate, hard metals, and

cast iron. Spread a film of oil along the intended line of cut for easier operation and longer

blade life. For cutting aluminum, kerosene is preferred.

RIP & CIRCLE CUTTING

Ripping and circle cutting without a pencil line are

easily done with the a rip fence and circle guide

(available at extra cost).

When ripping, slide the rip fence under the screw

from either side of the saw. Set the cross bar at

desired distance from blade and tighten screw. For

ripping, the cross bar should be down and against

the straight edge of the workpiece as shown in

figure I.

When circle cutting, adjust rip fence so that distance

from blade to hole in cross bar is at the desired

radius and tighten screw. Place saw so that hole in

cross bar is over center of circle to be cut (drill hole

for blade or cut inward from edge of material to get

blade into position). When saw is properly

positioned, drive a small nail through hole in cross

bar. Using rip fence as a pivot arm, begin cutting

circle. For circle cutting, the cross bar should be up,

as shown in figure J.

90550119 PC1800JS Jig Saw 4/9/09 7:52 AM Page 12

SERVICE AND REPAIRS

All quality tools will eventually require servicing and/or replacement of parts. For information about

PORTER-CABLE, its factory service centers or authorized warranty service centers, visit our

website at www.portercable.com or call our Customer Care Center at (888) 848-5175. All repairs

made by our service centers are fully guaranteed against defective material and workmanship. We

cannot guarantee repairs made or attempted by others.

You can also write to us for information at PORTER-CABLE, 4825 Highway 45 North, Jackson,

Tennessee 38305, (888) 848-5175 - Attention: Product Service. Be sure to include all of the

information shown on the nameplate of your tool (model number, type, serial number, etc.).

ACCESSORIES

Since accessories, other than those offered by PORTER-CABLE, have

not been tested with this product, use of such accessories with this tool could be

hazardous. To reduce the risk of injury, only PORTER-CABLE recommended

accessories should be used with this product.

A complete line of accessories is available from your PORTER-CABLE Factory Service

Center or a PORTER-CABLE Authorized Warranty Service Center. Please visit our

Web Site www.portercable.com for a catalog or for the name of your nearest supplier.

THREE YEAR LIMITED WARRANTY

PORTER-CABLE will repair or replace, without charge, any defects due to faulty

materials or workmanship for three years from the date of purchase for tools (two years

for batteries). This warranty does not cover part failure due to normal wear or tool

abuse. For further detail of warranty coverage and warranty repair information, visit

www.portercable.com or call (888) 848-5175. This warranty does not apply to

accessories or damage caused where repairs have been made or attempted by others.

This warranty gives you specific legal rights and you may have other rights which vary

in certain states or provinces.

In addition to the warranty, PORTER-CABLE tools are covered by our:

TROUBLESHOOTING

Problem Possible Cause Possible Solution

• Unit will not start. • Battery pack not installed properly. • Check battery pack

installation.

• Battery pack not charged. • Check battery pack

charging requirements.

• Battery pack will not charge. • Battery pack not inserted into charger. • Insert battery pack into

charger until LED

appears.

• Charger not plugged in. • Plug charger into a

working outlet. Refer to

“Important Charging Notes”

for more details.

• Surrounding air temperature • Move charger and battery

too hot or too cold. pack to a surrounding air

temperature of above 40

degrees F (4,5°C) or below

105 degrees F (+40,5°C).

SPECIAL NOTES FOR USE WITH LITHIUM BATTERIES

• Unit shuts off abruptly. • Battery pack has reached its • Allow battery pack to cool

maximum thermal limit. down.

• Out of charge. ( To • Place on charger and

maximize the life of the allow to charge.

battery pack it is designed

to shutoff abruptly when

the charge is depleted.)

For assistance with your product, visit our website at www.portercable.com for a list of

service centers, or call the PORTER-CABLE Customer Care Center at (888) 848-5175.

90550119 PC1800JS Jig Saw 4/9/09 7:52 AM Page 13

1 YEAR FREE SERVICE: PORTER-CABLE will maintain the tool and replace worn

parts caused by normal use, for free, any time during the first year after purchase.

90 DAY MONEY BACK GUARANTEE: If you are not completely satisfied with the

performance of your PORTER-CABLE Power Tool for any reason, you can return it

within 90 days from the date of purchase with a receipt for a full refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For

products sold in Latin America, see country specific warranty information contained in

the packaging, call the local company or see website for warranty information.

To register your tool for warranty service visit our website at www

.portercable.com

ARNING LABEL REPLACEMENT

If your warning labels become illegible or are missing, call (888) 848-5175 for a free

replacement.

The following are PORTER-CABLE trademarks for one or more power tools and accessories: a

gray and black color scheme; a “four point star” design; and three contrasting/outlined longitudinal

stripes. The following are also trademarks for one or more PORTER-CABLE and Delta products: 2

BY 4®, 890™, Air America®, AIRBOSS™, Auto-Set®, B.O.S.S.®, Bammer®, Biesemeyer®,

Builders Saw®, Charge Air®, Charge Air Pro®, CONTRACTOR SUPERDUTY®, Contractor's

Saw®, Delta®, DELTA®, Delta Industrial®, DELTA MACHINERY & DESIGN™, Delta Shopmaster

and Design®, Delta X5®, Deltacraft®, DELTAGRAM®, Do It. Feel It.®, DUAL LASERLOC AND

DESIGN®, EASY AIR®, EASY AIR TO GO™, ENDURADIAMOND®, Ex-Cell®, Front Bevel

Lock®, Get Yours While the Sun Shines®, Grip to Fit®, GRIPVAC™, GTF®, HICKORY

WOODWORKING®, Homecraft®, HP FRAMER HIGH PRESSURE®, IMPACT SERIES™,

Innovation That Works®, Jet-Lock®, Job Boss®, Kickstand®, LASERLOC®, LONG-LASTING

WORK LIFE®, MAX FORCE™, MAX LIFE®, Micro-Set®, Midi-Lathe®, Monsoon®, MONSTER-

CARBIDE™, Network®, OLDHAM®, Omnijig®, PC EDGE®, Performance Crew™, Performance

Gear®, Pocket Cutter®, Porta-Band®, Porta-Plane®, PORTER-CABLE®, PORTER-CABLE

Professional Power Tools®, Powerback®, POZI-STOP™, Pressure Wave®, PRO 4000®, Proair®,

Quicksand and Design®, Quickset II®, QUIET DRIVE TECHNOLOGY™, QUIET DRIVE

TECHNOLOGY AND DESIGN™, Quik-Change®, QUIK-TILT®, RAPID-RELEASE™, RAZOR®,

Redefining Performance®, Riptide®, Safe Guard II®, Sand Trap and Design®, Sanding Center®,

Saw Boss®, Shop Boss®, Sidekick®, Site Boss®, Speed-Bloc®, Speedmatic®, Stair Ease®,

Steel Driver Series®, SUPERDUTY®, T4 & DESIGN®, THE AMERICAN WOODSHOP®, THE

PROFESSIONAL EDGE®, Thin-Line®, Tiger Saw®, TIGERCLAW®, TIGERCLAW AND

DESIGN®, Torq-Buster®, TRU-MATCH®, T-Square®, Twinlaser®, Unifence®, Uniguard®,

UNIRIP®, UNISAW®, UNITED STATES SAW®, Veri-Set®, Versa-Feeder®, VIPER®, VT™, VT

RAZOR™, Water Driver®, WATER VROOM®, Waveform®, Whisper Series®, X5®, YOUR

ACHIEVEMENT. OUR TOOLS.®

Trademarks noted with ® are registered in the United States Patent and Trademark Office and may

also be registered in other countries. Other trademarks may apply.

4825 Highway 45 North

Jackson, Tennessee 38305

(888) 848-5175

www.portercable.com

90550119 PC1800JS Jig Saw 4/9/09 7:52 AM Page 14

Manuel d'instructions

www.portercable.com

N° DE CATALOGUE

PC1800JS

Scie sauteuse orbitale

sans fil à vitesse variable

Blocs-piles et chargeurs vendus séparément

90550119 PC1800JS Jig Saw 4/9/09 7:52 AM Page 15

Avertissements de sécurité généraux pour les outils

électriques

AVERTISSEMENT! Lire tous les avertissements de sécurité et toutes les

directives. Le non-respect des avertissements et des directives pourrait se

solder par un choc électrique, un incendie et/ou une blessure grave.

Conserver tous les avertissements et toutes les directives pour un usage

ultérieur.

Le terme «outil électrique» cité dans les avertissements se rapporte à votre

outil électrique à alimentation sur secteur (avec fil) ou par piles (sans fil).

1) Sécurité du lieu de travail

a) Tenir la zone de travail propre et bien éclairée. Les endroits sombres sont

souvent des causes d'accidents.

b) Ne pas faire fonctionner d’outils électriques dans un milieu déflagrant, soit

en présence de liquides inflammables, de gaz ou de poussière. Les outils

électriques produisent des étincelles qui peuvent enflammer la poussière ou les

vapeurs.

c) Éloigner les enfants et les curieux au moment d’utiliser un outil électrique.

Une distraction pourrait vous en faire perdre la maîtrise.

2) Sécurité en matière d’électricité

a) Les fiches des outils électriques doivent correspondre à la prise. Ne jamais

modifier la fiche en aucune façon. Ne jamais utiliser de fiche d’adaptation avec

un outil électrique mis à la terre. Le risque de choc électrique sera réduit par

l’utilisation de fiches non modifiées correspondant à la prise.

b) Éviter tout contact physique avec des surfaces mises à la terre comme des

tuyaux, des radiateurs, des cuisinières et des réfrigérateurs. Le risque de

choc électrique est plus élevé si votre corps est mis à la terre.

c) Ne pas exposer les outils électriques à la pluie ou à d'autres conditions où il

pourrait être mouillé. La pénétration de l’eau dans un outil électrique augmente

le risque de choc électrique.

d) Ne pas utiliser abusivement le cordon d’alimentation. Ne jamais utiliser le

cordon pour transporter, tirer ou débrancher un outil électrique. Tenir le

cordon éloigné de la chaleur, de l’huile, des bords tranchants ou des pièces

mobiles. Les cordons endommagés ou emmêlés augmentent les risques de choc

électrique.

e) Pour l’utilisation d’un outil électrique à l’extérieur, se servir d’une rallonge

convenant à une telle utilisation. L’utilisation d’une rallonge conçue pour

l’extérieur réduit les risques de choc électrique.

f) S’il est impossible d’éviter l’utilisation d’un outil électrique dans un endroit

humide, brancher l’outil dans une prise ou sur un circuit d’alimentation

dotés d’un disjoncteur de fuite à la terre (GFCI). L’utilisation de ce type de

disjoncteur réduit les risques de choc électrique.

3) Sécurité personnelle

a) Être vigilant, surveiller le travail effectué et faire preuve de jugement

lorsqu’un outil électrique est utilisé. Ne pas utiliser d’outil électrique en cas

de fatigue ou sous l’influence de drogues, d’alcool ou de médicaments. Un

simple moment d’inattention en utilisant un outil électrique peut entraîner des

blessures corporelles graves.

b) Utiliser des équipements de protection individuelle. Toujours porter une

protection oculaire. L’utilisation d’équipements de protection comme un masque

antipoussière, des chaussures antidérapantes, un casque de sécurité ou des

protecteurs auditifs lorsque la situation le requiert réduira les risques de blessures

corporelles.

c) Empêcher les démarrages intempestifs. S’assurer que l’interrupteur se

trouve à la position d’arrêt avant de relier l’outil à une source d’alimentation

et/ou d’insérer un bloc-piles, de ramasser ou de transporter l’outil.

Transporter un outil électrique alors que le doigt repose sur l’interrupteur ou

brancher un outil électrique dont l’interrupteur est à la position de marche risque

de provoquer un accident.

90550119 PC1800JS Jig Saw 4/9/09 7:52 AM Page 16

d) Retirer toute clé de réglage ou clé standard avant de démarrer l’outil. Une

clé standard ou une clé de réglage attachée à une partie pivotante peut causer

des blessures.

e) Ne pas trop tendre les bras. Conserver son équilibre en tout temps. Cela

permet de mieux maîtriser l’outil électrique dans les situations imprévues.

f) S’habiller de manière appropriée. Ne pas porter de vêtements amples ni de

bijoux. Garder les cheveux, les vêtements et les gants à l’écart des pièces

mobiles. Les vêtements amples, les bijoux ou les cheveux longs risquent de

rester coincés dans les pièces mobiles.

g) Si des composants sont fournis pour le raccordement de dispositifs de

dépoussiérage et de ramassage, s’assurer que ceux-ci sont bien raccordés

et utilisés. L’utilisation d’un dispositif de dépoussiérage peut réduire les dangers

engendrés par les poussières.

4) Utilisation et entretien d’un outil électrique

a) Ne pas forcer un outil électrique. Utiliser l’outil électrique approprié à

l’application. L’outil électrique approprié effectuera un meilleur travail, de façon

plus sûre et à la vitesse pour laquelle il a été conçu.

b) Ne pas utiliser un outil électrique dont l’interrupteur est défectueux. Tout

outil électrique dont l’interrupteur est défectueux est dangereux et doit être réparé.

c) Débrancher la fiche du secteur ou le bloc-piles de l’outil électrique avant de

faire tout réglage ou changement d’accessoire, ou avant de ranger l’outil

électrique. Ces mesures préventives réduisent les risques de démarrage

accidentel de l’outil électrique.

d) Ranger les outils électriques hors de la portée des enfants, et ne permettre

à aucune personne n’étant pas familière avec un outil électrique (ou son

manuel d’instruction) d’utiliser ce dernier. Les outils électriques deviennent

dangereux entre les mains d’utilisateurs inexpérimentés.

e) Entretenir les outils électriques. Vérifier les pièces mobiles pour s’assurer

qu’elles sont bien alignées et tournent librement, qu’elles sont en bon état

et ne sont affectées par aucun trouble susceptible de nuire au bon

fonctionnement de l’outil électrique. En cas de dommage, faire réparer

l’outil électrique avant toute nouvelle utilisation. Beaucoup d’accidents sont

causés par des outils électriques mal entretenus.

f) S’assurer que les outils de coupe sont aiguisés et propres. Les outils de

coupe bien entretenus et affûtés sont moins susceptibles de se coincer et sont

plus faciles à contrôler.

g) Utiliser l’outil électrique, les accessoires, les forets, etc. conformément aux

présentes directives en tenant compte des conditions de travail et du travail

à effectuer. L’utilisation d’un outil électrique pour toute opération autre que celle

pour laquelle il a été conçu est dangereuse.

5) Utilisation et entretien du bloc-piles

a) Ne recharger l’outil qu’au moyen du chargeur précisé par le fabricant.

L’utilisation d’un chargeur qui convient à un type de bloc-piles risque de

provoquer un incendie s’il est utilisé avec un autre type de bloc-piles.

b) Utiliser les outils électriques uniquement avec les blocs-piles conçus à cet

effet. L’utilisation de tout autre bloc-piles risque de causer des blessures ou un

incendie.

c) Lorsque le bloc-piles n’est pas utilisé, le tenir éloigné des objets

métalliques, notamment des trombones, de la monnaie, des clés, des clous,

des vis, etc., qui peuvent établir une connexion entre les deux bornes. Le

court-circuit des bornes du bloc-piles risque de provoquer des étincelles, des

brûlures ou un incendie.

d) En cas d’utilisation abusive, le liquide peut gicler hors du bloc-piles, éviter

tout contact. Si un contact accidentel se produit, laver à grande eau. Si le

liquide entre en contact avec les yeux, obtenir des soins médicaux. Le

liquide qui gicle hors du bloc-piles peut provoquer des irritations ou des brûlures.

6) Réparation

a) Faire réparer l’outil électrique par un réparateur professionnel en n’utilisant

que des pièces de rechange identiques. Cela permettra de maintenir une

utilisation sécuritaire de l’outil électrique.

90550119 PC1800JS Jig Saw 4/9/09 7:52 AM Page 17

CONSIGNES DE SÉCURITÉ PARTICULIÈRES

• Tenir l’outil par les surfaces isolées prévues à cette fin lorsqu’il risque d’entrer en

contact avec des fils cachés ou le cordon, car de tels contacts peuvent mettre les

pièces métalliques de l’outil sous tension, engendrant des risques de choc électrique.

• Lorsqu’on est installé sur une échelle ou un échafaudage pour travailler, on doit

déposer l’outil sur le côté lorsqu’on ne s’en sert plus. Bien que certains outils munis

d’un gros bloc-piles puissent être placés à la verticale, dans cette position, ils peuvent

facilement être renversés.

• Utiliser des brides de fixation ou un autre dispositif de fixation permettant de

fixer solidement et de soutenir la pièce sur une plateforme stable. Tenir la pièce

avec la main ou contre son corps la rend instable et risque de provoquer une perte de

maîtrise de l’outil.

• Tenir les mains éloignées de la zone de découpe. Ne jamais mettre la main sous le

matériau pour quelque raison que ce soit. Tenir la partie avant de la scie par sa zone

de prise profilée. Ne pas mettre les doigts ou le pouce à proximité de la scie

alternative et du mécanisme de serrage de la lame. Ne pas stabiliser la scie en

saisissant la semelle.

• Maintenir les lames affûtées. Les lames émoussées peuvent faire zigzaguer la lame

ou la bloquer sous la pression.

• Au moment de couper un tuyau ou un conduit, s’assurer qu’ils sont exempts d’eau,

de câblage électrique, etc.

• Attendre l’immobilisation complète du moteur avant de retirer la lame du trait de

scie (la rainure créée par la lame en coupant). En effet, une lame en mouvement

risque de percuter la pièce et se briser, d’endommager la pièce ou de provoquer une

perte de la maîtrise de l’outil, ce qui risquerait de provoquer des blessures corporelles.

• Ne jamais tenir la pièce dans les mains, sur les genoux ou contre toute partie du

corps en cours de découpe. La scie pourrait glisser et la lame pourrait atteindre le

corps et provoquer des blessures.

• Maintenir les poignées sèches, propres, exemptes d’huile et de graisse. Cela

permet de mieux maîtriser l’outil.

• Nettoyer l’outil régulièrement, particulièrement après une utilisation intensive. La

poussière et les saletés contenant des particules métalliques s’accumulent souvent sur

les surfaces internes de l’outil et pourraient créer un risque de choc électrique.

• Ne pas faire fonctionner cet outil durant de longues périodes. Les vibrations

causées par le fonctionnement de cet outil peuvent provoquer des blessures

permanentes aux doigts, aux mains et aux bras. Utiliser des gants pour amortir

davantage les vibrations, prendre de fréquentes périodes de repos et limiter la durée

quotidienne d’utilisation.

TOUJOURS porter des lunettes de sécurité. Les lunettes de vue

ne constituent PAS des lunettes de sécurité. Utiliser également un masque facial ou

anti-poussière si l’opération de découpe génère de la poussière. TOUJOURS

PORTER UN ÉQUIPEMENT DE PROTECTION HOMOLOGUÉ :

• protection oculaire conforme à la norme ANSI Z87.1 (CAN/CSA Z94.3);

• protection auditive ANSI S12.6 (S3.19);

• protection des voies respiratoires conformes aux normes NIOSH/OSHA/MSHA.

certains outils électriques, tels que les sableuses, les scies,

les meules, les perceuses ou certains autres outils de construction, peuvent

produire de la poussière contenant des produits chimiques reconnus par l’État

de la Californie comme étant susceptibles d’entraîner le cancer, des

malformations congénitales ou pouvant être nocifs pour le système

reproductif. Parmi ces produits chimiques, on retrouve :

· le plomb dans les peintures à base de plomb,

· la silice cristalline dans les briques et le ciment et autres produits de maçonnerie,

· l’arsenic et le chrome dans le bois de sciage ayant subi un traitement chimique.

Le risque associé à de telles expositions varie selon la fréquence avec laquelle on

effectue ces travaux. Pour réduire l’exposition à de tels produits, il faut travailler dans un

endroit bien aéré et utiliser le matériel de sécurité approprié, tel un masque

anti-poussières spécialement conçu pour filtrer les particules microscopiques.

90550119 PC1800JS Jig Saw 4/9/09 7:52 AM Page 18

• Éviter tout contact prolongé avec la poussière soulevée par cet outil ou autres

outils électriques. Porter des vêtements de protection et nettoyer les parties

exposées du corps à l’eau savonneuse. S’assurer de bien se protéger afin d’éviter

d’absorber par la bouche, les yeux ou la peau des produits chimiques nocifs.

Cet outil peut produire et répandre de la poussière susceptible

de causer des dommages sérieux et permanents au système respiratoire.

Toujours utiliser un appareil respiratoire anti-poussières approprié approuvé par le

NIOSH ou l’OSHA. Diriger les particules dans le sens opposé du visage et du corps.

Porter les protecteurs auditifs appropriés durant l’utilisation

de l’outil. Dans certaines conditions et selon la durée d’utilisation, le bruit engendré par

ce produit peut contribuer à la perte de l’ouïe.

LIGNES DIRECTRICES EN MATIÈRE DE SÉCURITÉ - DÉFINITIONS

Il est important que vous lisiez et compreniez ce mode d’emploi. Les informations qu’il

contient concernent VOTRE SÉCURITÉ et visent à ÉVITER TOUT PROBLÈME. Les

symboles ci-dessous servent à vous aider à reconnaître cette information.

Indique une situation dangereuse imminente qui, si elle n’est pas

évitée, causera la mort ou des graves blessures.

Indique une situation potentiellement dangereuse qui, si elle n’est

pas évitée, pourrait causer la mort ou de graves blessures.

Indique une situation potentiellement dangereuse qui, si elle n’est pas

évitée, pourrait causer des blessures mineures ou modérées.

Utilisé sans le symbole d’alerte à la sécurité, indique une situation

potentiellement dangereuse qui, si elle n’est pas évitée, peut résulter en des dommages

à la propriété.

• En cas d’utilisation d’une rallonge, s’assurer que les valeurs nominales de la rallonge

utilisée correspondent bien à celles de l’outil alimenté. L’usage d’une rallonge de calibre

insuffisant causera une chute de tension entraînant perte de puissance et surchauffe. Le

tableau ci-dessous illustre les calibres à utiliser selon la longueur de rallonge et l’intensité

nominale indiquée sur la plaque signalétique. En cas de doutes, utiliser le calibre suivant.

Plus le calibre est petit, plus la rallonge peut supporter de courant.

Calibre minimal des cordons de rallonge

Tension Longueur totale du cordon en pieds

120V 0-25 26-50 51-100 101-150

(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)

240V 0-50 51-100 101-200 201-300

(0-15,2m) (15,2-30,4m) (30,4-60,9m) (60,9-91,4m)

Intensité (A)

Au Au Calibre moyen des fils (AWG)

moins plus

0-6 18 16 16 14

6 - 10 18 16 14 12

10 - 12 16 16 14 12

12 - 16 14 12 Non recommandé

90550119 PC1800JS Jig Saw 4/9/09 7:52 AM Page 19

SYMBOLES

• L’étiquette apposée sur votre outil pourrait comprendre les symboles suivants. Les

symboles et leurs définitions sont indiqués ci-après :

V ..............volts A................ampères

Hz ............hertz W ..............watts

min............minutes ............courant alternatif

..........courant continue non............régime à vide

..............Construction de classe I

(mis à la terre)

..............Construction classe II

............

borne de terre

............symbole d’alerte à la ../min ou rpm.. révolutions ou alternance par minute

sécurité

sfpm..........pieds linéaires par minute

DIRECTIVES DE SÉCURITÉ IMPORTANTES POUR LES

CHARGEURS DE PILES

CONSERVER CES DIRECTIVES : ce mode d’emploi comprend d’importantes directives

de sécurité pour les chargeurs de piles.

• Avant d’utiliser le chargeur, lire toutes les directives et tous les avertissements figurant

sur le chargeur, le bloc-piles et le produit utilisé avec le bloc-piles.

risque de choc électrique. Éviter la pénétration de tout liquide dans

le chargeur.

Blocs-piles au LI-ION et chargeurs

correspondants

Bloc-piles : LI-ION 18V

Chargeur : pour piles au

LI-ION

PC18BL

PC18BLX

PC18BLEX

PCLMVC

PCXMVC

Description N° de cat.

Blocs-piles au NI-CD et chargeurs

correspondants

Ce produit est compatible avec tous les modèles de piles et de chargeurs

énumérés dans le tableau ci-dessous.

Bloc-piles : NI-CD 18V

Chargeur : pour piles au

NI-CD

PC18B

PCMVC

PCXMVC

Description N° de cat.

DESCRIPTION

FONCTIONNELLE

1. Détente à vitesse variable

2. Bouton de verrouillage

3. Levier de blocage de la lame de la scie

4. Roulette d’appui de la lame de la scie

5. Plaque de la semelle

6. Molette de blocage de la

plaque de la semelle

7. Levier de coupe

8. Adaptateur de dispositif de

dépoussiérage

90550119 PC1800JS Jig Saw 4/9/09 7:52 AM Page 20

La page charge ...

Porter-Cable 90550119 Manuel utilisateur

Marque: Porter-Cable

Modèle: 90550119

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Porter-Cable 90550119 User manual
español: Porter-Cable 90550119 Manual de usuario

Porter-Cable 90550119 Manuel utilisateur

Ce manuel convient également à

Porter-Cable 90550119 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents