GE PGSS5PJZSS Le manuel du propriétaire

GEAppliances.com

Refrigerators

Bottom Freezer

225D1804P010 49-60614 04-10 GE

Safety Instructions . . . . . . . . . . .2, 3

Operating Instructions

Additional Features . . . . . . . . . . . . . . . . .8

Automatic Icemaker . . . . . . . . . . . .11, 12

Care and Cleaning . . . . . . . . . . . . .12–13

Controls . . . . . . . . . . . . . . . . . . . . . . . . . .4–5

Crispers and Pans . . . . . . . . . . . . . . . . . . .9

Freezer . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Replacing the Light Bulbs . . . . . . . . . .14

Shelves and Bins . . . . . . . . . . . . . . . . . .7, 8

Water Filter . . . . . . . . . . . . . . . . . . . . . . . . .6

Installation Instructions

Installing the Anti-Tip

Floor Bracket . . . . . . . . . . . . . . . . . .16–17

Installing the Refrigerator . . . . . .18–22

Installing the Water Line . . . . . . . .30–32

Preparing to Install

the Refrigerator . . . . . . . . . . . . . . . . . . . .15

Removing and Replacing the

Freezer Drawers . . . . . . . . . . . . . . .23–26

Removing and Replacing

the Doors (Double Door

Refrigerator Models only) . . . . . . .27–29

Troubleshooting Tips . . . . . .33–37

Normal Operating Sounds . . . . . . . . . .33

Consumer Support

Consumer Support . . . . . . . .Back Cover

Performance Data Sheet . . . . . . . . . . .41

State of California Water

Treatment Device Certificate . . . . . . .42

Warranty for Canadian

Customers . . . . . . . . . . . . . . . . . . . . . . . . .40

Warranty for U.S. Customers . . . . . . .39

Réfrigérateurs

Congélateur inférieur

Refrigeradores

Congelador inferior

Write the model and serial

numbers here:

Model # ____________________

Serial #______________________

Find these numbers on a label

on the right side, near the top of the

refrigerator compartment.

Models 21 and 25 Double Freezer Drawers

Manuel d’utilisation

et d’installation

Owner’s Manual and

Installation Instructions

Manual del propietario

y instalación

La section française commence à la page 43

La sección en español empieza en la página 83

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:



 This refrigerator must be properly installed

and located in accordance with the Installation

Instructions before it is used.



 Do not allow children to climb, stand or hang on the

shelves in the refrigerator. They could damage the

refrigerator and seriously injure themselves.



 Do not touch the cold surfaces in the freezer

compartment when hands are damp or wet.

Skin may stick to these extremely cold surfaces.



 Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other

appliance.



 Keep fingers out of the “pinch point” areas;

clearances between the doors and between the

doors and cabinet are necessarily small. Be careful

closing doors when children are in the area.



 In refrigerators with automatic icemakers, avoid

contact with the moving parts of the ejector

mechanism, or with the heating element that

releases the cubes. Do not place fingers or hands

on the automatic icemaking mechanism while

the refrigerator is plugged in.



 Unplug the refrigerator before cleaning and making

repairs.

NOTE: We strongly recommend that any servicing

be performed by a qualified individual.



 Setting either or both controls to 0 (off) does not

remove power to the light circuit.



 Do not refreeze frozen foods which have

thawed completely.

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not problems of

the past. Junked or abandoned refrigerators are still

dangerous…even if they will sit for “just a few days.”

If you are getting rid of your old refrigerator, please

follow the instructions below to help prevent

accidents.

Before You Throw Away Your Old

Refrigerator or Freezer:

 Take off the doors.

 Leave the shelves in place so that children may not

easily climb inside.

Refrigerants

All refrigeration products contain refrigerants,

which under federal law must be removed prior

to product disposal. If you are getting rid of an

old refrigeration product, check with the company

handling the disposal about what to do.

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly recommend against

the use of an extension cord.

However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United

States) or a CSA certified (in Canada), 3-wire grounding type appliance extension cord having a grounding type

plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

DANGER! RISK OF CHILD ENTRAPMENT

Consumer Support Troubleshooting Tips Operating Instructions Safety Instructions

Installation

Instructions

2

3

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

Installation

Instructions

GEAppliances.com

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with

a 3-prong (grounding) plug which mates with a

standard 3-prong (grounding) wall outlet to

minimize the possibility of electric shock hazard

from this appliance.

Have the wall outlet and circuit checked by a

qualified electrician to make sure the outlet is

properly grounded.

Where a standard 2-prong wall outlet is encountered,

it is your personal responsibility and obligation to

have it replaced with a properly grounded 3-prong

wall outlet.

The refrigerator should always be plugged into its

own individual electrical outlet which has a voltage

rating that matches the rating plate.

This provides the best performance and also prevents

overloading house wiring circuits which could cause a

fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the

power cord. Always grip plug firmly and pull straight

out from the outlet.

Repair or replace immediately all power cords that

have become frayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage

along its length or at either end.

When moving the refrigerator away from the wall, be

careful not to roll over or damage the power cord.

READ AND FOLLOW THIS SAFETY INFORMATION

CAREFULLY.

SAVE THESE INSTRUCTIONS

4

About the controls with temperature settings.

The temperature controls are preset in the factory at 37°F for the refrigerator

compartment and 0°F for the freezer compartment. Allow 24 hours for the temperature

to stabilize to the preset recommended settings.

The temperature controls can display both the SET temperature as well as the actual

temperature in the refrigerator and freezer. The actual temperature may vary slightly

from the SET temperature based on usage and operating environment.

Setting either or both controls to OFF stops cooling in both the freezer and refrigerator

compartments, but does not shut off electrical power to the refrigerator.

For Controls-on-the-Door Models:

Models with External Dispensers:

To change the Refrigerator temperature:

Access By: Home > Refrigerator

Activate By: Using the arrows to select the desired

temperature. You must press ENTER to set the new

temperature.

To change the Freezer temperature:

Access By: Home > Freezer

Activate By: Using the arrows to select the desired

temperature. You must press ENTER to set the new

temperature.

Once the desired temperature has been set, the display will

return to the HOME screen and show the set temperatures

underneath the actual temperature display for several

seconds. Several adjustments may be required. Each time

you adjust the controls, allow 24 hours for the refrigerator

to reach the temperature you have set.

For Controls Inside the Refrigerator:

Opening the door displays the actual temperature. To

change the temperature, press either the WARMER or

COLDER touch pads until the desired temperature is

displayed.

Once the desired temperature has been set, the

temperature display will return to the actual refrigerator

and freezer temperatures after 5 seconds. Several

adjustments may be required.

Each time you adjust controls, allow 24 hours for the

refrigerator to reach the temperature you have set.

To turn the cooling system off, tap the WARMER pad for

either the refrigerator or the freezer until the display shows

OFF. To turn the unit back on, press the COLDER pad for

either the refrigerator or freezer. Then press the COLDER

pad again and it will go to the preset points of 0°F for the

freezer and 37°F for the refrigerator. Setting either or both

controls to OFF stops cooling in both the freezer and

refrigerator compartments, but does not shut off electrical

power to the refrigerator.

Models with External Dispensers:

Access By: Home > Options > Information and Settings >

Cooling System Off

To turn the cooling system back on, press the touch screen

and press the ON button.

Activate By: Pressing ENTER.

Changing the Temperature

NOTE: The refrigerator is shipped with protective film covering the temperature controls.

If this film was not removed during installation, remove it now.

Consumer Support Troubleshooting Tips Operating Instructions Safety Instructions

Installation

Instructions

H

OME

H

ELP

L

OCK

Hold for 3 Seconds

to activate Lock

T

URBO

C

OOL

E

NERGY

S

AVER

D

OOR

A

LARM

F

REEZER

F0

R

EFRIGERATOR

F37

O

PTIONS

P

RECISE

F

ILL

E

NERGY

S

AVER

ON

(Models with controls inside the refrigerator)

(Models with controls on the door)

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

Installation

Instructions

5

About TurboCool.

™

(on some models) GEAppliances.com

How it Works

TurboCool rapidly cools the refrigerator

compartment in order to more quickly

cool foods. Use TurboCool when adding a

large amount of food to the refrigerator

compartment, putting away foods after they

have been sitting out at room temperature

or when putting away warm leftovers. It can

also be used if the refrigerator has been

without power for an extended period.

Once activated, the compressor will turn on

immediately and the fans will cycle on and

off at high speed as needed for eight hours.

The compressor will continue to run until

the refrigerator compartment cools to

approximately 34°F (1°C), then it will cycle

on and off to maintain this setting. After 8

hours, or if TurboCool is pressed again, the

refrigerator compartment will return to the

original setting.

How to Use

Press TurboCool. The refrigerator

temperature display will show .

After TurboCool is complete, the

refrigerator compartment will return

to the original setting.

NOTES: The refrigerator temperature

cannot be changed during

TurboCool.

The freezer temperature is not

affected during TurboCool.

When opening the refrigerator door

during TurboCool, the fans will

continue to run if they have

cycled on.

T

URBO

C

OOL

About Door Alarm (on some models)

The door alarm will sound if any door is open

for more than 2 minutes. The beeping stops

when you close the door.

(on some models)

DOOR

ALARM

(on some models)

Water Filter Cartridge

The water filter cartridge is located in the

back upper right corner of the refrigerator

compartment.

When to Replace the Filter

There is a replacement indicator light for the

water filter cartridge on the temperature

display. This light will turn orange to tell you

that you need to replace the filter soon. The

filter cartridge should be replaced when the

replacement indicator light turns red or if the

flow of water to the dispenser or icemaker

decreases.

On models with external dispensers, the top

of the LCD screen will display, “Replace

Water Filter.”

Installing the Filter Cartridge

If you are replacing the cartridge, first

remove the old one by slowly turning it

to the left. DO NOT pull down on the

cartridge. A small amount of water may

drip down.

CAUTION: If air has been

trapped in the system, the filter cartridge may

be ejected as it is removed. Use caution when

removing.

Remove the protective foil from the end

of the cartridge.

Fill the replacement cartridge with water

from the tap to allow for better flow from

the dispenser immediately after

installation.

Lining up the arrow on the cartridge and

the cartridge holder, slowly rotate the

cartridge clockwise until it stops. When

the cartridge is properly installed, you will

feel it “click” as it locks into place. Do not

overtighten.

Run 1

1

⁄2 gallons from the dispenser to

clear the system and prevent sputtering.

See To Use the Dispenser section.

Press and hold the RESET WATER FILTER

pad for 3 seconds.

NOTE: A newly-installed water filter cartridge

may cause water to spurt from the

dispenser.

Filter Bypass Plug

You must use the filter bypass plug when a

replacement filter cartridge is not available.

The icemaker will not operate without the

filter or filter bypass plug.

Replacement Filters:

To order additional filter cartridges

in the United States, visit our Website,

GEAppliances.com, or call GE Parts and

Accessories, 800.626.2002.

Filter Model MWF

Customers in Canada should consult

the yellow pages for the nearest Mabe

Service Center.

About the water filter. (on some models)

Consumer Support Troubleshooting Tips Operating Instructions Safety Instructions

Installation

Instructions

6

(on some models)

R

ESET

F

ILTER

(on some models)

Cartridge

Holder

Cartridge

Holder

7

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

Installation

Instructions

Rearranging the Shelves

To remove:

Remove all items from the shelf.

Tilt the shelf up at the front.

Lift the shelf up at the back and bring

the shelf out.

To replace:

While tilting the shelf up, insert the top

hook at the back of the shelf in a slot on

the track.

Lower the front of the shelf until the

bottom of the shelf locks into place.

Spillproof Shelves (on some models)

Spillproof shelves have special edges to help

prevent spills from dripping to lower shelves.

To remove or replace the shelves, see

Rearranging the Shelves.

About the shelves and bins. GEAppliances.com

Not all features are on all models.

Shelves in the refrigerator compartment are adjustable.

Refrigerator Compartment

Slide-Out Spillproof Shelf (on some models)

The slide-out spillproof shelf allows you to

reach items stored behind others. The special

edges are designed to help prevent spills

from dripping to lower shelves.

To remove:

Remove all items from shelf.

Slide the shelf out until it stops.

Lift the front edge of the shelf until the

central tabs are above the front bar.

Continue pulling the shelf forward until

it can be removed.

To replace:

Place the rear shelf tabs just in front of

the central notches on the shelf frame.

Slide the shelf in until the central tabs are

slightly behind the front bar.

Lower the shelf into place until it is

horizontal and slide the shelf in.

Make sure that the shelf sits flat after

reinstallation and doesn’t move freely from

side to side.

Make sure you push the shelves all the way in

before you close the door.

Some models have wire shelves that can

be adjusted in the same manner.

Non-Adjustable Bins on the Door

To remove: Lift the bin straight up, then

pull out.

To replace: Engage the bin in the molded

supports on the door and push down. It will

lock in place.

Adjustable Bins on the Door

Adjustable bins can easily be carried from

refrigerator to work area.

To remove: Lift bin straight up, then pull out.

To replace or relocate: Slide in the bin just

above the molded door supports, and push

down. The bin will lock in place.

The snugger helps prevent tipping, spilling

or sliding of small items stored on the door

shelf. Grip the finger hold near the rear of the

snugger and move it to fit your needs.

About the additional features.

Not all features are on all models.

Non-Adjustable Beverage Rack

To remove: Lift the rack straight up, then pull

out.

To replace: Engage the rack in the molded

supports on the door and push down. It will

lock in place.

About the shelves and bins.

Consumer Support Troubleshooting Tips Operating Instructions Safety Instructions

Installation

Instructions

8

Adjustable Divider in Freezer Basket

The freezer basket has a divider that can be

both repositioned or removed.

To remove: Pull the divider forward until the

rear locating tabs are out of the slots. Turn

the divider slightly to the side to release the

front locating tabs and lift out.

To replace: Turn the divider slightly to one

side so the tabs on the front fit into the vent

slots on the basket. Position the divider so

the back locating tabs snap into place in the

back vent slots.

To reposition: Remove the divider. Slide the

divider to the right of center to the desired

location and replace as instructed above.

NOTE: The divider cannot be placed to the

left of center because it would interfere with

the icemaker.

Tabs

9

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

Installation

Instructions

About the crispers and pans. GEAppliances.com

Not all features are on all models.

Fruit and Vegetable Crisper

Excess water that may accumulate in the

bottom of the drawers or under the drawers

should be wiped dry.

Adjustable Humidity Crisper (on some models)

Slide the control all the way to the

HIGH setting to provide higher humidity

recommended for most vegetables.

Slide the control all the way to the LOW

setting to provide lower humidity levels

recommended for most fruits.

Adjustable Temperature Deli Pan (on some models)

Slide the control all the way to the left for the

coldest temperature.

To remove:

Remove the fruit and vegetable drawers.

Pull the drawer out to the stop position.

Lift the lid to access the 4 swing locks.

Rotate all four swing locks to the unlock

position.

Lift the front of the drawer up and out.

To replace:

Make sure all four swing locks are in the

unlock position.

Place the sides of the drawer into the

drawer supports, making sure the swing

locks fit on the drawer slots.

Lock all four swing locks by rotating them

to the lock position.

Lower the lid and slide in the drawer.

Replace the fruit and vegetable drawers.

How to Remove and Replace the Deli Pan

Swing Locks

10

Freezer Shelves and Baskets

A full-width upper basket in top drawer

Ice bucket

A deep full-width lower basket with

the divider in the bottom drawer

Basket Removal (Top Drawer)

To remove the 2-piece basket:

Open the bottom freezer drawer until

it stops.

Pull the divider forward until the rear

locating tabs are out of the slots. Turn the

divider slightly to the side to release the

front locating tabs and lift out.

The freezer basket rests on the metal

slide brackets and is held in place with

swing locks.

Turn the swing locks from horizontal to

vertical position.

Lift the front portion of the basket up,

rotate it toward you, and bring it straight

up to remove.

Lift the back portion of the basket up and

out of the drawer.

When replacing the 2-piece basket:

Place the rear of the basket onto the

metal slide brackets. There will be 2 pins

on each underside of the back that will

align for securing the basket.

Seat the front of the basket onto

the metal slide brackets and over the

swing locks.

Turn the swing locks from vertical to

horizontal position to lock the basket

in place.

Turn the divider slightly to one side so

the tabs on the front fit into the vent slots

on the basket. Position the divider so the

back locating tabs snap into place in the

back vent slots.

To remove the full-width basket:

Open the top freezer drawer until it stops.

The freezer basket rests on the inside

tabs on the drawer slides.

Lift the front end of the basket so that the

front two alignment tabs come out of the

metal slide brackets first. Then rotate the

front edge of the basket up while lifting

the remaining two rear alignment tabs

out of the metal slide brackets.

Make sure the plastic sleeves remain

attached to the 4 slots on the metal slide

brackets.

When replacing the full-width basket:

Tilt the basket back and lower it down into

the drawer. Rotate the basket to a horizontal

position and press it down into the slots.

NOTE: Always be sure that all 4 basket tabs

are engaged in the metal slide brackets

before sliding back into the freezer.

The Bottom Drawer basket is a 2-piece

basket.

About the freezer.

Not all features are on all models.

Appearance and features may vary

Appearance may vary

Tab

Consumer Support Troubleshooting Tips Operating Instructions Safety Instructions

Installation

Instructions

Basket Removal (Bottom Drawer)

Pins

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

Installation

Instructions

About the automatic icemaker. GEAppliances.com

Automatic Icemaker (on some models)

The icemaker will produce seven cubes

per cycle—approximately 100–130 cubes

in a 24-hour period, depending on freezer

compartment temperature, room

temperature, number of door openings

and other use conditions.

See below for how to access ice and reach

the power switch.

If the refrigerator is operated before the

water connection is made to the icemaker,

set the power switch in the O (off) position.

When the refrigerator has been connected to

the water supply, set the power switch to the

l (on) position. The icemaker power light will

turn green when the freezer light switch is

pressed in or when the freezer door is closed.

The icemaker will fill with water when it cools

to 15°F (–10°C). A newly installed refrigerator

may take 12 to 24 hours to begin making

ice cubes.

You will hear a buzzing sound each time the

icemaker fills with water.

Throw away the first few batches of ice to

allow the water line to clear.

Be sure nothing interferes with the sweep of

the feeler arm.

When the bin fills to the level of the feeler

arm, the icemaker will stop producing ice.

It is normal for several cubes to be joined

together.

If ice is not used frequently, old ice cubes will

become cloudy, taste stale and shrink.

NOTE: In homes with lower-than-average

water pressure, you may hear the icemaker

cycle multiple times when making one batch

of ice.

NOTE: Set the power switch to the O (off)

position if the water supply is shut off.

A newly installed refrigerator may take 12 to 24 hours to begin making ice.

Icemaker

Feeler Arm

Power

Switch

Green Power

Light

Accessing Ice and Reaching the

Power Switch

To reach the icemaker power switch,

open the top freezer drawer and remove the

full-width basket. Always be sure to replace

the basket.

To access ice, open the bottom freezer

drawer. The ice bucket is located below

the mullion. Pull it forward to access ice.

To access ice.

Ice

Bucket

To reach the power switch.

Icemaker Accessory Kit

If your refrigerator did not come already

equipped with an automatic icemaker,

an icemaker accessory kit is available at

extra cost.

Check the back of the refrigerator for the

specific icemaker kit needed for your model.

To Use the Dispenser (on some models)

Press the glass gently against the top of the

dispenser cradle.

The spill shelf is not self-draining. To reduce

water spotting, the shelf should be cleaned

regularly.

If no water is dispensed when the refrigerator

is first installed, there may be air in the water

line system. Press the dispenser arm and run

1

⁄2 gallons to remove trapped air from the

water line and to fill the water system. To

flush out impurities in the water line, throw

away the first six glassfuls of water.

Locking the Dispenser

Press the LOCK pad for 3 seconds to lock

the dispenser and control panel. To unlock,

press and hold the pad again for 3 seconds.

H

OME

H

ELP

L

OCK

Hold for 3 Seconds

to activate Lock

T

URBO

C

OOL

E

NERGY

S

AVER

D

OOR

A

LARM

FREEZER

F-3

REFRIGERATOR

F34

OPTIONSPRECISE FILL

E

NERGY

S

AVER

ON

Spill Shelf

11

Dispenser Cradle

Mullion

Care and cleaning of the refrigerator.

Cleaning the Outside

The door handles and trim. Clean with a

cloth dampened with soapy water. Dry with

a soft cloth. Do not use wax on the door

handles and trim.

Keep the outside clean. Wipe with a clean

cloth lightly dampened with kitchen

appliance wax or mild liquid dish detergent.

Dry and polish with a clean, soft cloth.

Do not wipe the refrigerator with a soiled

dish cloth or wet towel. These may leave a

residue that can erode the paint. Do not

use scouring pads, powdered cleaners,

bleach or cleaners containing bleach

because these products can scratch and

weaken the paint finish.

The stainless steel panels and door

handles. Stainless steel (on some models)

can be cleaned with a commercially

available stainless steel cleaner. A spray-on

stainless steel cleaner works best.

Do not use appliance wax or polish on the

stainless steel.

Silver-plated plastic parts. Wash parts with

soap or other mild detergents. Wipe clean

with a sponge, damp cloth or paper towel.

Do not scrub with steel-wool pads or other

abrasive cleaners.

Cleaning the Inside

To help prevent odors, leave an open box of

baking soda in the refrigerator and freezer

compartments.

Unplug the refrigerator before cleaning. If

this is not practical, wring excess moisture

out of sponge or cloth when cleaning around

switches, lights or controls.

Use an appliance wax polish on the inside

surface between the doors.

Use warm water and baking soda solution—

about a tablespoon (15 ml) of baking soda to

a quart (1 liter) of water. This both cleans and

neutralizes odors. Rinse and wipe dry.

After cleaning the door gaskets, apply a thin

layer of petroleum jelly to the door gaskets at

the hinge side. This helps keep the gaskets

from sticking and bending out of shape.

Avoid cleaning cold glass shelves with hot

water because the extreme temperature

difference may cause them to break. Handle

glass shelves carefully. Bumping tempered

glass can cause it to shatter.

Do not wash any plastic refrigerator parts

in the dishwasher.

Silver-accented plastic parts. Wash parts

with soapy water. Wipe clean with a sponge,

damp cloth or paper towel.

Do not scrub with steel-wool pads or other

abrasive cleaners.

12

Consumer Support Troubleshooting Tips Operating Instructions Safety Instructions

Installation

Instructions

About the automatic icemaker.

Precise Fill (on some models)

This water dispenser is equipped with a feature

called Precise Fill. This feature allows you to

choose a precise amount of water. Units include

ounces, cups, pints or liters.

Models with External Dispensers

Access By: Home > Precise Fill > Set Amount

Activate By: Using the arrow buttons to select the

desired amount. Press MORE UNITS to select

between CUPS, OUNCES, PINTS or LITERS.

Press the cup against the cradle and water

will begin dispensing. It will automatically

stop when the amount set has been

dispensed. The display will show there

is no water left to dispense, then reset.

NOTE: Do not leave the dispenser unattended

when water is being dispensed.

If you would like to stop dispensing water

before the specified amount has been

dispensed, just remove the cup from the

cradle. The display will show the amount left

to dispense.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

Installation

Instructions

13

For long vacations or absences, remove food

and unplug the refrigerator. Clean the interior

with a baking soda solution of one

tablespoon (15 ml) of baking soda to one

quart (1 liter) of water. Leave the doors open.

Set the icemaker power switch to the O (off)

position and shut off the water supply to

the refrigerator.

If the temperature can drop below freezing,

have a qualified servicer drain the water

supply system (on some models) to prevent

serious property damage due to flooding.

GEAppliances.com

Behind the Refrigerator

Be careful when moving the refrigerator

away from the wall. All types of floor

coverings can be damaged, particularly

cushioned coverings and those with

embossed surfaces.

Raise the leveling legs located at the bottom

front of the refrigerator.

Pull the refrigerator straight out and return it

to position by pushing it straight in. Moving

the refrigerator in a side direction may

result in damage to the floor covering or

refrigerator.

Lower the leveling legs until they touch

the floor.

When pushing the refrigerator back, make

sure you don’t roll over the power cord or

icemaker supply line (on some models) and

ensure the anti-tip bracket is engaged (if

equipped).

Preparing for Vacation

Preparing to Move

Secure all loose items such as base grille,

shelves and drawers by taping them

securely in place to prevent damage.

When using a hand truck to move the

refrigerator, do not rest the front or back

of the refrigerator against the hand truck.

This could damage the refrigerator. Handle

only from the sides of the refrigerator.

Be sure the refrigerator stays in an upright

position during moving.

14

Consumer Support Troubleshooting Tips Operating Instructions Safety Instructions

Installation

Instructions

Refrigerator Lights

For models with LED lights:

An authorized technician will need to replace

the LED light.

Freezer Light

Replacing the light bulbs.

Turning the control to the 0 (off) position does not remove power to the light circuit.

Appearance may vary

CAUTION: Light bulbs may

be hot.

Unplug the refrigerator.

Remove the freezer basket for access.

The bulb is located at the rear of the

freezer inside a light shield.

To remove, grasp the shield at the top

and pull out to release the tabs at the

bottom.

After replacing with an appliance bulb

of the same or lower wattage, replace

the shield and freezer basket.

Plug the refrigerator back in.

For models with incandescent lights:

CAUTION: Light bulbs may

be hot.

Unplug the refrigerator.

To remove the light shield, grasp the

shield at the back and pull out to release

the tabs at the back.

Rotate the shield down and then forward

to release the tabs at the front of

the shield.

After replacing with an appliance bulb

of the same or lower wattage, replace

the shield.

Plug the refrigerator back in.

NOTE: Appliance bulbs may be ordered from

GE Parts and Accessories, 800.626.2002.

Light

Shield

Installation

Refrigerator

Instructions

Models 21 and 25

Double Freezer Drawers

Questions? Call 800.GE.CARES (800.432.2737) or visit our Website at: GEAppliances.com

In Canada, call 1.800.561.3344 or visit our Website at: www.GEAppliances.ca

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT — Save these instructions for local

inspector’s use.

•

IMPORTANT — Observe all governing codes and

ordinances.

• Note to Installer – Be sure to leave these instructions with

the Consumer.

• Note to Consumer – Keep these instructions for future

reference.

• Skill level – Installation of this appliance requires basic

mechanical skills.

• Completion time – Refrigerator Installation

20 minutes

Water Line Installation

30 minutes

Anti-Tip Bracket Installation

20 minutes

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not covered

under the Warranty.

PREPARATION

MOVING THE REFRIGERATOR INDOORS

If the refrigerator will not fit through a doorway, the

refrigerator door and freezer drawer can be removed.

• To remove the refrigerator door, see Step 1 in the

Reversing the Door Swing section.

• To remove the freezer drawer, see the Removing the

Freezer Drawer section.

WATER SUPPLY TO THE ICEMAKER AND DISPENSER

(ON SOME MODELS)

If the refrigerator has an icemaker, it will have to be

connected to a cold water line. A GE water supply kit

(containing tubing, shutoff valve, fittings and instructions)

is available at extra cost from your dealer, by visiting our

Website at GEAppliances.com (in Canada at

www.GEAppliances.ca) or from Parts and Accessories,

800.626.2002 (In Canada 1.800.661.1616).

TOOLS YOU MAY NEED

Adjustable Wrench

1/4 Outer Diameter

Compression Nut

and Ferrule (sleeve) (icemaker

models only)

Phillips-Head Screwdriver

15

3/8 and 5/16 Socket

Ratchet/Driver

3/32 , 1/8 and 1/4

Allen wrenches

MATERIALS YOU MAY NEED (not included)

Pencil

1/8 Drill Bit and

Electric or Hand Drill

Tape measure

1/4 Nut Driver

Lag Bolts

Anchor Sleeves

For Anti-Tip Bracket Mounted on CONCRETE Floors Only

Drill Bit Appropriate for Anchors

Wire Cutters

Level

LOCATING THE ANTI-TIP

FLOOR BRACKET

Place the anti-tip floor bracket locator template

(included inside the anti-tip kit) onto the floor

up against the rear wall, within W, and in line

with the desired location of the RH side of the

refrigerator (see Figure 1).

Place the anti-tip floor bracket onto the locator

template with its RH floor holes lined up with

the floor holes indicated on the template sheet,

approximately 7

1

⁄4 from the edge of the sheet

or the RH side of the refrigerator.

Hold down in position and use the anti-tip floor

bracket as a template for marking the holes

based upon your configuration and type of

construction as shown in Step 3. Mark the hole

locations with a pencil, nail or awl.

NOTE:

• It is REQUIRED to use at least 2 screws to

mount the floor bracket (one on each side of

the anti-tip floor bracket). Both must be into

either the wall or the floor. Figure 2 indicates

all the acceptable mounting configurations

for screws. Identify the screw holes on the

anti-tip floor bracket for your configuration.

MEASURE CABINET OPENING

AVAILABLE VS. REFRIGERATOR WIDTH

Measure width of cabinet opening where

refrigerator will be placed, W.

Be sure to account for any countertop

overhang, baseboard thickness and any

clearance desired. Width, W, should not be less

than 36 inches. The refrigerator will be placed

approximately in the middle of this opening.

WARNING

Under certain circumstances, this refrigerator

can tip forward.

Injury to persons can result.

Install Anti-Tip Bracket packed with this

refrigerator.

1

Baseboard

Thickness

or Countertop

Overhang

(Whichever

Is Greater) Plus

Any Desired

Clearance

Rear Wall

Front

RH Side

2

A

B

C

W

Base

Bracket

on the

Refrigerator

2 Wall Holes

RH Side of

Refrigerator

Floor – Concrete

(2 Holes)

Floor – Wood

(2 Holes)

7

1

⁄4

Locator Template

Sheet

Floor Bracket

to Install

RH Holes

Rear RH Corner

of Cabinet Wall

REFRIGERATOR

Figure 1 – Installation Overview

16

Installation Instructions

INSTALLING THE ANTI-TIP FLOOR BRACKET (on 21 ft. models)

Installation Instructions

LOCATING THE ANTI-TIP

FLOOR BRACKET (cont.)

2

Preferred Installation –

Wood

Preferred Installation –

Concrete

Minimum Acceptable #1 –

Wall Plate Stud

Minimum Acceptable #2 – Wood

Floor

Minimum Acceptable #3 –

Concrete Floor

Figure 2 – Acceptable Screw Placement

Locations

CONCRETE Wall and Floor Construction:

• Anchors required (not provided):

4 each 1/4” x 1 1/2” lag bolts

4 each 1/2” O.D. sleeve anchors

• Drill the recommended size holes for the

anchors into the concrete at the center of

the holes marked in Step 2.

• Install the sleeve anchors into the drilled

holes. Place the anti-tip floor bracket as

indicated in Step 2. Remove the locator

template from the floor.

• Install the lag bolts through the anti-tip floor

bracket and tighten appropriately.

WOOD Wall and TILE Floor Construction:

• For this special case, locate the 2 wall holes

identified in Fig. 1. Drill an angled 1/8” pilot

hole (approx. as shown in Fig. 3) in the center

of each hole.

• Mount the anti-tip floor bracket using the

Minimum Acceptable Installation #1, as

illustrated in Fig. 2.

C

B

ANTI-TIP BRACKET INSTALLATION

WOOD Wall and Floor Construction:

• Drill the appropriate number of 1/8” pilot

holes in the center of each floor bracket hole

being used (a nail or awl may be used if a drill

is not available) AND remove the locator

template from the floor.

• Mount the anti-tip floor bracket by fastening

the 2, or preferably 4, #10-16 hex-head

screws tightly into place as illustrated in

Figure 3.

3

A

POSITIONING THE REFRIGERATOR

TO ENGAGE THE ANTI-TIP FLOOR

AND BASE BRACKETS

Before pushing the refrigerator into the

opening, plug the power cord into the

receptacle and connect waterline (if equipped).

Check for leaks.

Locate the refrigerator’s RH side and move

back approximately in line with the RH side of

the cabinet opening, W. This should position the

anti-tip floor bracket to engage the anti-tip

base bracket on the refrigerator.

Gently roll the refrigerator back into the

cabinet opening until it comes to a complete

stop. Check to see if the refrigerator front lines

up with the cabinet front face. If not, carefully

rock the refrigerator forward and backward

until engagement occurs and you notice that

the refrigerator is fully pushed up against the

rear wall.

OPTIONAL: Adjust the rear (and front) wheel

height settings to fully engage the rear anti-tip

brackets, while also aligning the refrigerator

front with the cabinet front face.

4

A

C

B

D

Figure 3 – Attachment to

Wall and Floor

NOTE:

If you pull the refrigerator out and away from the

wall for any reason, make sure the anti-tip floor

bracket is engaged when the refrigerator is pushed

back against the rear wall.

Rear RH Corner of

the Refrigerator

Floor

Wall

Plate

Stud

Floor

Bracket

2 Screws Must

Enter Wood or

Metal Stud

Wall

17

Installation Instructions

INSTALLING THE REFRIGERATOR

REFRIGERATOR LOCATION

• Do not install the refrigerator where the temperature will

go below 60°F (16°C) because it will not run often enough

to maintain proper temperatures.

• Do not install the refrigerator where the temperature will

go above 100°F (37°C) because it will not perform properly.

• Install it on a floor strong enough to support it fully loaded.

CLEARANCES

Allow the following clearances for ease of installation, proper

air circulation and plumbing and electrical connections.

Standard Depth Counter Depth

Models Models

Sides 1/8 (3 mm) 1/8 (3 mm)

Top 1 (25 mm) 1 (25 mm)

Back 1 (25 mm) 1/2 (13 mm)

CONNECTING THE REFRIGERATOR

TO THE HOUSE WATER LINE

(icemaker and dispenser models)

A cold water supply is required for automatic icemaker

operation. If there is not a cold water supply, you

will need to provide one. See Installing the Water

Line section.

NOTES:

• Before making the connection to the refrigerator, be

sure the refrigerator power cord is not plugged into

the wall outlet.

• If your refrigerator does not have a water filter, we

recommend installing one if your water supply has

sand or particles that could clog the screen of the

refrigerator’s water valve. Install it in the water line

near the refrigerator. If using GE SmartConnect

™

Refrigerator Tubing Kit, you will need an additional

tube (WX08X10002) to connect the filter. Do not cut

plastic tube to install filter.

1

REMOVE TOP CAP (on some models)

•IMPORTANT NOTE: This refrigerator is 34-1/2 deep.

Doors and passageways leading to the installation

location must be at least 36 wide in order to leave

the doors and handles attached to the refrigerator

while transporting it into the installation location. If

passageways are less than 36 , the refrigerator doors

and handles can easily be scratched and damaged.

The top cap and doors can be removed to allow the

refrigerator to be safely moved indoors. Start with

Step A.

•If it is not necessary to remove doors, skip Step A.

Leave tape and all packaging on doors until the

refrigerator is in the final location.

•SKID REMOVAL: Tilt refrigerator to each side to

remove skid.

•NOTE: Use a padded hand truck to move this

refrigerator. Place the refrigerator on the hand truck

with a side against the truck. We strongly recommend

that TWO PEOPLE move and complete this installation.

Locate and remove the two Phillips head screws on

the top of the refrigerator. Remove the two screws

on each side at the rear of the top cap. Lift off and

remove top cap.

Remove the fresh-food door. Refer to Steps 1

through 3 of “Reversing the Door Swing” section.

Remove the bottom freezer drawer. Refer to

“Removing Freezer Drawers” section.

Move refrigerator to the installation location.

A

B

C

D

18

REMOVE TOP CAP (cont.) (on some models)

REINSTALL DOORS, DRAWERS AND TOP CAP

Carefully lower the door onto the center hinge. Reinstall

top hinge. NOTE: Ensure the door is properly aligned to

the case top to avoid readjustment of the door during

top cap reinstallation.

Place cap over the top of the refrigerator. Reinstall the

original screws in the top and back of the cap.

Reinstall the bottom freezer drawer. Refer to “Replacing

the Freezer Drawers” section.

E

F

G

A

Top

Hinge B

CONNECTING THE REFRIGERATOR

TO THE HOUSE WATER LINE (cont.)

If you are using copper tubing, place a

compression nut and ferrule (sleeve) onto the

end of the tubing coming from the house cold

water supply.

If you are using the GE SmartConnect

™

tubing, the nuts are already assembled to the

tubing.

If you are using copper tubing, insert the end

of the tubing into the refrigerator connection,

at the back of the refrigerator, as far as

possible. While holding the tubing, tighten

the fitting.

If you are using GE SmartConnect

™

tubing,

insert the molded end of the tubing into the

refrigerator connection, at the back of the

refrigerator, and tighten the compression

nut until it is hand tight. Then tighten one

additional turn with a wrench. Overtightening

may cause leaks.

Fasten the tubing into the clamp provided to

hold it in position. You may need to pry open

the clamp.

One of the illustrations below will look like the

connection on your refrigerator.

Icemaker-Ready models

Icemaker-Installed Models

19

Installation Instructions

1

A

B

C

1/4 Tubing

Tubing Clamp

1/4

Compression

Nut

Ferrule

(sleeve)

SmartConnect

™

Tubing

Refrigerator

Connection

TURN ON THE WATER SUPPLY

(icemaker and dispenser models)

Turn the water on at the shutoff valve (house

water supply) and check for any leaks.

2

PLUG IN THE REFRIGERATOR

On models with an icemaker, before plugging in

the refrigerator, make sure the icemaker power

switch is set to the O (off) position.

See the grounding information attached to the

power cord.

3

PUT THE REFRIGERATOR IN PLACE

Move the refrigerator to its final location. Make

sure the back side of the refrigerator engages the

anti-tip bracket properly. The anti-tip floor bracket

should line up with the cutout in the back bottom

of the refrigerator, and fit through the cutout when

the refrigerator is pushed into position. (Refer to

page 16, Step 2A for more information.)

4

1/4 Copper

Tubing

1/4

Compression

Nut

Ferrule

(sleeve)

SmartConnect

™

Tubing

Refrigerator

Connection

Tubing

Clamp

LEVEL THE REFRIGERATOR

Turn the front roller adjusting

screws clockwise to raise the

refrigerator, counterclockwise

to lower it. Use a 3/8 hex

wrench with extension, or an

adjustable wrench.

To adjust the rollers on 21

‘ Counter Depth models:

These models also have rear adjustable rollers so you

can align the refrigerator with your kitchen cabinets.

Use a 3/8 hex wrench with extension to turn the

screws for the rear rollers—clockwise to raise the

refrigerator, counterclockwise to lower it.

5

Roller adjusting screws

Installation Instructions

REMOVE THE FRESH FOOD

DOOR HANDLE

(For placement in the installation location or

reversal of the handles – on some models)

Stainless steel (on some models):

REMOVING THE DOOR

HANDLE: Loosen the

set screws with the

3/32 Allen wrench

and remove the

handle. NOTE: For

Double Door models,

follow the same

procedure on the

opposite door.

Plastic handle (on

some models):

REMOVING THE DOOR HANDLE: Depress the tab on

the underside of the handle and slide the handle up

and off of the mounting fasteners.

REVERSING THE

DOOR HANDLE

(on some models):

• Remove the

handle mounting

fasteners with a

1/4 Allen

wrench and

transfer the

handle mounting

fasteners to the

right side.

• Remove the logo

badge.

• Remove and

transfer the plug button to the left

side of the fresh food door. NOTE: Use a flat plastic

edge to prevent damaging the door. Remove any

adhesive on the door with a mild detergent. Remove

the paper covering on the adhesive backing on the

logo badge prior to carefully attaching the badge to

the door.

A

6

A

B

A

B

Mounting

Fasteners

Mounting

Fasteners

Badge

(appearance may vary)

REMOVE THE TOP AND BOTTOM

FREEZER DRAWER HANDLES

Stainless steel and plastic handles:

Loosen the set screws located on the underside of

the handle with the 1/8 Allen wrench and remove

the handle.

NOTE: If the handle mounting fasteners need to be

tightened or removed, use a 1/4 Allen wrench.

A

7

A

20

INSTALLING THE REFRIGERATOR (cont.)

A

La page charge ...

GE PGSS5PJZSS Le manuel du propriétaire

Ce manuel convient également à

GE PGSS5PJZSS Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents