Cub Cadet 11AB9M5710 Le manuel du propriétaire

Marque: Cub Cadet

Modèle: 11AB9M5710

Catégorie: Tondeuses à gazon

Taper: Le manuel du propriétaire

NOTE: This Operator’s Manual covers several models. Features may vary by model. Not all features in this manual are

applicable to all models and the model depicted may differ from yours.

OperatOr’s Manual

Safe Operation Practices • Assembly • Operation • Service And Maintenance

Form No. 769-22910B

(October 25, 2019)

Push Mower

WARNING

Read and follow all safety rules and instructions in this manual before attempting to operate this

machine.

Failure to comply with these instructions may result in personal injury - SAVE THESE INSTRUCTIONS.

WARNING

CALIFORNIA PROPOSITION 65

Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals

known to State of California to cause cancer and birth defects or other reproductive harm.

Record Product Information

Before setting up and operating your new

mower, please locate the model plate on the

equipment and record the information in the

provided area to the right. You can locate the

model plate by standing at the operator’s

position and looking down at the rear of the

deck. This information will be necessary, should

you seek technical support via our web site,

Customer Support Department, or with a local

authorized service dealer.

Model Number

Serial Number

English ........................................................................................................................................Page 2

Spanish (Español) ......................................................................................................................Page 16

French (Français) ........................................................................................................................Page 32

SAFE OPERATION PRACTICES

GENERAL INFORMATION

1. Read, understand, and follow all instructions on the mower

and in the manual(s) before attempting to assemble and

operate. Keep this manual in a safe place for future and

regular reference and for ordering replacement parts.

2. Be familiar with all controls and their proper operation.

3. Never allow children under 14 years of age to operate this

mower. Children 14 and over should read and understand

the instructions and safe operation practices in this manual

and on the mower and should be trained and supervised by

an adult.

4. Never allow adults to operate this mower without proper

instruction.

5. Store mower in a dry, clean area. Do not store next to

corrosive materials, such as fertilizer.

6. If situations occur which are not covered in this manual, use

care and good judgment. Contact your customer service

representative for assistance.

7. According to the U.S. Consumer Products Safety Commission

(CPSC) and the U.S. Environmental Protection Agency (EPA),

this product has an estimated useful life of seven (7) years,

under ordinary use conditions. At the end of its useful life,

have the product inspected annually to ensure all mechanical

and safety systems are operating properly, safely, and are

not worn excessively. Failure to do so may result in accident,

injury, or death.

PREPARATION BEFORE OPERATING

1. Thoroughly inspect the area where the mower is to be used.

Remove all stones, sticks, wire, bones, toys, and other foreign

objects which could be tripped over or picked up and thrown

by the blade(s). Thrown objects can cause serious personal

injury.

2. To help avoid blade contact or a thrown object injury, stay in

the operator zone behind the mower handles. Keep helpers

at least 75 feet (23 meters) from the mower while it is in

operation. Keep bystanders, children and pets inside while

the mower is in operation. Stop mower if anyone enters the

area.

3. Be aware of the mower and attachment discharge direction

and do not point the mower discharge at anyone.

4. Always wear safety glasses or safety goggles during

operation and while performing an adjustment or repair to

protect your eyes. Thrown objects which ricochet can cause

serious injury to the eyes.

5. Wear sturdy, rough-soled work shoes and close-fitting slacks

and shirts. Loose fitting clothes, jewelry and long hair can be

caught in moving parts. Shirts and pants that cover the arms

and legs and steel-toed shoes are recommended.

6. Never operate mower in bare feet, sandals, slippery or light-

weight (e.g. canvas) shoes.

7. Never over fill fuel tank. Fill tank to no more than 1” (2.5 cm)

below bottom of filler neck to allow space for fuel expansion.

8. Replace gasoline cap and tighten securely.

9. Use only accessories and attachments approved for this

mower by the mower manufacturer. Read, understand and

follow all instructions provided with the approved accessory

or attachment.

OPERATING

1. Data indicates that operators, age 65 years and above, are

involved in a large percentage of mower-related injuries.

These operators should evaluate their ability to operate the

mower safely enough to protect themselves and others from

serious injury.

2. Many injuries occur as a result of the mower being pulled

over the foot during a fall caused by slipping or tripping. Do

not hold on to the mower if you are losing your balance or

footing; immediately release the handle.

3. Never pull the mower back toward you while you are walking.

If you must back the mower away from a wall or obstruction

first look down and behind to avoid tripping and then follow

these steps:

a. Step back from mower to fully extend your arms.

b. Be sure you are well balanced with sure footing.

c. Pull the mower back slowly, no more than half way

toward you.

d. Repeat these steps as needed.

WARNING

This symbol points out important safety instructions which, if not followed, could endanger the personal

safety and/or property of yourself and others. Read and follow all instructions in this manual before

attempting to operate this machine. Failure to comply with these instructions may result in personal injury.

When you see this symbol, HEED ITS WARNING!

DANGER

This machine was built to be operated according to the safe operation practices in this manual. As with any type of

power equipment, carelessness or error on the part of the operator can result in serious injury. This machine is capable of

amputating fingers, hands, toes and feet and throwing debris. Failure to observe the following safety instructions could

result in serious injury or death.

SAFE OPERATION PRACTICES

4. Do not engage the drive control (if equipped) while starting

engine.

5. The blade control is a safety device. Never attempt to bypass

its operation. Doing so makes the safety device inoperative

and may result in personal injury through contact with the

rotating blade. The blade control must operate freely in

both directions and automatically return to the disengaged

(off) position when released. The cutting blade continues

to rotate for up to three seconds after the blade control is

released. Never place any part of the body in the blade area

until you are certain the blade has stopped rotating.

6. If the mower should start to vibrate abnormally, stop the

engine and check immediately for the cause. Vibration is

generally a warning of trouble.

7. Never operate mower without the proper trail shield,

discharge cover, grass catcher, blade control or other safety

protective devices in place and working. Never operate

mower with damaged safety devices. Failure to do so can

result in personal injury.

8. When starting engine, pull cord slowly until resistance is felt,

then pull rapidly. Rapid retraction of starter cord (kickback)

will pull hand and arm toward engine faster than you can let

go. Broken bones, fractures, bruises or sprains could result.

9. Do not put hands or feet near rotating parts or under the

cutting deck. Contact with the blade(s) can amputate hands

and feet.

10. Watch for holes, ruts, bumps, rocks, or other hidden objects.

Uneven terrain or hidden objects could cause a slip and/or

trip accident. Tall grass can hide obstacles.

11. Your mower is designed to cut normal residential grass of a

height no more than 7” (17.5 cm). Do not attempt to mow

through unusually tall, dry grass (e.g., pasture) or piles of

dry leaves.

12. Plan your mowing pattern to avoid discharge of material

toward roads, sidewalks, helpers and the like. Avoid

discharging material against a wall or obstruction which

may cause discharged material to ricochet back toward the

operator.

13. Shut the engine off and wait until the blade comes to

a complete stop before removing the grass catcher or

unclogging the chute. The cutting blade continues to rotate

for up to three seconds after the blade control is released.

Never place any part of the body in the blade area until

you are certain the engine is off and the blade has stopped

rotating.

14. A missing or damaged discharge door, chute or mulch plug

can cause blade contact or thrown object injuries.

15. Do not operate the mower without the discharge door, chute,

mulch plug or the entire grass catcher in its proper place.

16. Stop the mower blade when crossing gravel drives, walks, or

roads and while not cutting grass.

17. Mow only in daylight or good artificial light.

18. Do not operate the mower while under the influence of

alcohol or drugs.

19. The muffler and engine become very hot and can cause

serious burn injuries. Do not touch. Allow the mower to cool

for at least five minutes before storing or attempting any

service.

20. Never run an engine indoors or in a poorly ventilated area.

Engine exhaust contains carbon monoxide, an odorless and

deadly gas.

CHILDREN

1. Tragic accidents can occur if the operator is not alert to the

presence of children. Children are often attracted to the

mower and the mowing activity. They do not understand the

dangers. Never assume that children will remain where you

last saw them.

2. Keep bystanders, children and pets inside while the mower is

in operation under watchful care of a responsible adult other

than the operator. Stop mower if anyone enters the area.

3. Be alert and turn mower off if a child or bystander enters

the area.

4. Never allow children under 14 years of age to operate this

mower. Children 14 and over should read and understand

the instructions and safe operation practices in this manual

and on the mower and should be trained and supervised by

an adult.

5. This mower is a precision piece of power equipment, not a

plaything. Therefore, exercise extreme caution at all times.

This mower has been designed to perform one job: to mow

grass. Do not use it for any other purpose.

6. Use extreme care when approaching blind corners, doorways,

shrubs, trees or other objects that may block your vision of a

child who may run into the path of the mower.

7. Keep children away from hot or running engines. They can

suffer burns from a hot engine or muffler.

8. If your mower is equipped with an Electric Start Push Key,

remove the key when the mower is unattended to prevent

unauthorized operation. Make certain the key is inaccessible

to small children.

SLOPE OPERATION FOR WALK-BEHIND MOWERS

1. Slopes are a major factor related to slip and fall accidents

which can result in severe injury or death. All slopes require

extra caution. If you feel uneasy on the slope, do not mow it.

2. For your safety, measure any slope before using the mower

on the sloped area. Use a slope measuring device in addition

to the slope gauge included as part of this manual to measure

slopes before operating this mower on a sloped or hilly area.

Smart phone applications can be also utilized to measure

slopes. If the slope is greater than 15 degrees (25%) as shown

on the slope gauge or a slope measuring device, do not

operate this mower on that area or serious injury could result.

3. Do not mow on slopes greater than 15 degrees (25%).

SAFE OPERATION PRACTICES

4. Only mow across slopes, never mow up and down slopes.

5. The mower may speed up when turning downhill, always

turn uphill. Maintain control of the mower at all times.

6. Do not mow on wet grass. Unstable footing could cause

slipping.

7. Do not operate the mower under any conditions where

traction or stability is in question. Always be sure of your

footing. A slip and fall can cause serious personal injury. If

you feel you are losing your balance or footing, release the

blade control handle immediately and the blade will stop

rotating within three (3) seconds.

8. Stay at least 3 feet (1 meter) from drop-offs, ditches,

embankments or the edge of water. You could lose your

balance or footing.

FIRE & FUEL

1. To avoid personal injury or property damage use extreme

care in handling gasoline. Gasoline is extremely

flammable and the vapors are explosive.

Serious personal injury can occur when gasoline is spilled on

yourself or your clothes which can ignite. Wash your skin and

change clothes immediately.

2. Extinguish all cigarettes, cigars, pipes and other sources of

ignition.

3. Only use an approved portable fuel (gasoline) container. Use

only containers certified by EPA, CARB, and/or OSHA.

4. Never remove gas cap or add fuel while the engine is hot or

running. Allow engine to cool at least five minutes before

refueling.

5. Never fuel the mower indoors.

6. Never store the mower or fuel container inside where there is

an open flame, spark or pilot light as on a water heater, space

heater, furnace, clothes dryer or other gas appliances.

7. If fuel is spilled, wipe it off the engine and mower. Clean up

oil or fuel spillage and remove any fuel soaked debris. Move

the mower to another area. Wait at least 5 minutes before

starting the engine.

8. To reduce fire hazards, keep mower free of grass, leaves, or

other debris build-up. Follow the instructions in the Service

and Maintenance section to keep your mower free of debris.

9. Never over fill fuel tank. Fill tank to no more than 1” (25mm)

below bottom of filler neck to allow space for fuel expansion.

10. Replace gas cap and tighten securely.

11. Allow a mower to cool at least five minutes before fueling

or storing.

12. Never fill containers inside a vehicle or on a truck or trailer

bed with a plastic liner. Always place containers on the

ground away from your vehicle before filling.

13. When practical, remove gas-powered equipment from

the truck or trailer and refuel it on the ground. If this is not

possible, then refuel such equipment on a trailer with a

portable container, rather than from a gasoline dispenser

nozzle.

14. Keep the nozzle in contact with the rim of the fuel tank or

container opening at all times until fueling is complete. Do

not use a nozzle lock-open device.

SERVICE

1. Keep the mower in good working order. Replace worn or

damaged parts.

2. To avoid serious injury or death, do not modify engine in

any way. Tampering with the governor setting can lead to

a runaway engine and cause it to operate at unsafe speeds.

Never tamper with factory setting of engine governor. Do

not change the engine governor settings or over-speed the

engine. The governor controls the maximum safe operating

speed of the engine.

3. Mower blades are sharp. Wrap the blade or wear gloves, and

use extra caution when servicing them.

4. Before cleaning, repairing, or inspecting, make certain the

blade and all moving parts have stopped. Disconnect the

spark plug wire and ground against the engine to prevent

unintended starting.

5. Ensure the blade comes to a complete stop within (3) three

seconds after operating the blade control. If the blade does

not stop in less than three seconds, your mower must be

serviced professionally by an authorized service dealer.

Check for proper operation per the Service and Maintenance

section.

6. Regularly check the safety interlock system for proper

function, as described later in this manual. If the safety

interlock system does not function properly, have your

mower serviced professionally by an authorized service

dealer.

7. Never tamper with the blade control safety interlock or other

safety devices. Check for proper operation per the Service and

Maintenance section.

8. Check the mower blade and engine mounting bolt torque

in accordance to the Service and Maintenance section in

this manual. Also, visually inspect blade for damage (e.g.,

excessive wear, bent, cracked). Replace the blade with the

original equipment manufacturer’s (O.E.M.) blade only.

9. Use of service parts which do not meet the original

equipment specifications may lead to improper performance

and compromise safety.

10. Keep all nuts, bolts, and screws tight to be sure the

equipment is in safe working condition. Check all hardware

for tightness per the Service and Maintenance section.

SAFE OPERATION PRACTICES

11. After striking a foreign object, stop the engine, disconnect

the spark plug wire(s) and ground against the engine.

Thoroughly inspect the mower for any damage. Repair the

damage before starting and operating

12. Never attempt to make wheel cutting height adjustments or

repairs to the mower while the engine is running.

13. Grass catcher components and the discharge cover are subject

to wear and damage which could expose moving parts or

allow objects to be thrown. For safety protection, frequently

check components and replace immediately with original

equipment manufacturer’s (O.E.M.) parts only. “Use of parts

which do not meet the original equipment specifications may

lead to improper performance and compromise safety.”

14. Maintain or replace safety and instruction labels, as

necessary.

15. Observe proper disposal laws and regulations for gas, oil, etc.

to protect the environment.

NOTICE REGARDING EMISSIONS

Engines which are certified to comply with California and

federal EPA emission regulations for SORE (Small Off Road

Equipment) are certified to operate on regular unleaded

gasoline, and may include the following emission

control systems: Engine Modification (EM) and Three Way

Catalyst (TWC) if so equipped.

When required, models are equipped with low

permeation fuel lines and fuel tanks for evaporative

emission control. California models may also include a

carbon canister. Please contact Customer Support for

information regarding the evaporative emission control

configuration for your model.

SPARK ARRESTOR

WARNING

This mower is equipped with an internal combustion

engine and should not be used on or near any

unimproved forest-covered, brush-covered or grass-

covered land unless the engine’s exhaust system is

equipped with a spark arrestor meeting applicable local

or state laws (if any).

If a spark arrestor is used, it should be maintained in

effective working order by the operator. In the State of

California the above is required by law (Section 4442 of

the California Public Resources Code). Other states may

have similar laws. Federal laws apply on federal lands.

A spark arrestor for the muffler is available through your

nearest engine authorized service dealer or contact the

service department, P.O. Box 361131 Cleveland, Ohio

44136-0019.

SLOPE GAUGE (BACK COVER)

WARNING

Slopes are a major factor related to slip and fall accidents

which can result in severe injury or death. All slopes

require extra caution. If you feel uneasy on the slope,

do not mow it. Do not mow on slopes greater than 15

degrees (25%). Only mow across slopes, never mow up

and down slopes.

USE THE SLOPE GAUGE ON THE BACK COVER AS SHOWN TO

DETERMINE IF A SLOPE IS TOO STEEP FOR SAFE OPERATION!

To check the slope, proceed as follows:

1. Open manual to page and fold along the dashed line.

2. Locate a vertical object on or behind the slope (e.g. a pole,

building, fence, tree, etc.)

3. Align either side of the slope gauge with the object.

4. Adjust gauge up or down until the left corner touches the

slope.

5. If there is a gap below the gauge, the slope is too steep for

safe operation.

SAFETY SYMBOLS

This page depicts and describes safety symbols that may appear on this mower. Read, understand, and follow all instructions on the

mower before attempting to assemble and operate.

Symbol Description

WARNING – READ THE OPERATOR’S MANUAL(S)

Read, understand and follow all the safety rules and instructions in the

manual(s) and on the mower before attempting to operate this mower. Failure

to comply with this information may result in personal injury or death. Keep

this manual in a safe location for future and regular reference.

DANGER — AVOID AMPUTATION INJURY

Do not put hands or feet near or under the cutting deck. Contact with the blade

can amputate hands and feet.

DANGER — AVOID CHILD RUNOVER/BLADE INJURY

Do not mow when children or others are around. To help avoid blade contact

or a thrown object injury, stay in the operator zone behind the mower

handles. Keep helpers at least 75 feet (23 meters) from the mower while it is

in operation. Keep bystanders, children and pets inside while the mower is in

operation. Stop mower if anyone enters the area.

DANGER — AVOID THROWN OBJECT INJURY

Keep helpers at least 75’ (23 meters) from mower during operation. Remove

all stones, sticks, wire, bones, toys, and other foreign objects which could be

picked up and thrown by the blade(s). Do not operate the mower without the

discharge cover or entire grass catcher in its proper place.

DANGER — AVOID SLIP AND FALL ON SLOPES

Slopes are a major factor related to slip and fall accidents which can result in

severe injury or death. All slopes require extra caution. If you feel uneasy on

the slope, do not mow it. Do not mow on slopes greater than 15 degrees (25%).

Only mow across slopes, never mow up and down slopes.

WARNING—GASOLINE IS FLAMMABLE

Allow the engine to cool at least five minutes before refueling.

WARNING— AVOID BURN INJURY

The muffler and engine become very hot and can cause serious burn injuries.

Do not touch. Allow the mower to cool for at least five minutes before storing

or attempting any service.

WARNING

Your Responsibility—Restrict the use of this power machine to persons who read, understand and follow the

warnings and instructions in this manual and on the machine - SAVE THESE INSTRUCTIONS!

ASSEMBLY

IMPORTANT: This mower is shipped without gasoline or oil in

the engine. Be certain to service engine with gasoline and oil

as instructed in the Operation section of the Engine Operator’s

Manual before starting or operating your mower.

NOTE: Reference to right and left hand side of the Lawn Mower is

observed from the operating position.

Unpacking

OPENING CARTON

1. Cut each corner of the carton vertically from top to bottom.

2. Remove all loose parts:

• Grass Catcher (if equipped)

• Engine Oil

3. Remove loose packing material.

REMOVING MOWER FROM CARTON

1. Lift mower from the rear to detach it from underlying carton

material and roll mower out of carton.

2. Check carton thoroughly for any other loose parts.

Mower Assembly

Perform the following Procedures to assemble and set up the

mower:

• Handle Assembly

• Pull-Out Handle. See page 7.

• Vertical Storage Handle. See page 8.

• Recoil starter Rope Handle Assembly

• Attaching the Grass Catcher (if equipped)

• Attaching Side Discharge Cover (if equipped)

NOTE: If necessary, refer to the procedures in the Adjustments

Section after assembling the mower.

Handle Assembly

PULLOUT HANDLE

1. Remove any packing material which may be between upper

and lower handles.

2. Remove knobs or wing nuts and carriage bolts from the

handle (Figure 1). Do not loosen or remove adjacent hex head

screws.

Knobs Shown

Figure 1

3. While stabilizing mower so it doesn’t move, pivot upper

handle up (Figure 2). Do not crimp blade control cable while

lifting the handle up.

Figure 2

4. Remove T-bolts from the handle brackets (Figure 3).

Figure 3

5. Pull upward on the handle (Figure 4) until holes in lower

handle line up with holes in handle brackets (Figure 3 deck

cutaway).

NOTE: When pulling upward on handle, do not pull handle all

the way out of the handle brackets.

Figure 4

ASSEMBLY

6. Insert the T-bolts removed in STEP 4 through the handle

brackets and lower handle (Figure 4) and tighten securely to

secure the handle in place.

7. Reattach knobs or wing nuts and carriage bolts removed in

STEP 2 into lower holes of the handle (Figure 5).

Knobs Shown

Figure 5

VERTICAL STORAGE HANDLE

1. Remove the four carriage bolts and nuts from the lower

handles (Figure 6).

Figure 6

2. Unlock the two handle release levers. See inset, Figure 7.

3. Ensure the lower handles are folded forward towards the

front of the mower.

Figure 7

4. Using the four carriage bolts and nuts removed in STEP

2, secure the upper handle to the lower handle. Tighten

hardware securely to secure the handle in place.

Figure 8

5. While stabilizing mower so it doesn’t move, lift the upper

handle up (a) (Figure 9). Do not crimp blade control cable

while lifting the handle up.

6. When lifting the upper handle ensure the position indicator

(b) aligns with one of three handle positions (c). See inset,

Figure 9.

7. Lock the two handle release levers. See inset, Figure 9.

8. Ensure all hardware is securely tightened.

Figure 9

ASSEMBLY

Recoil Starter Rope Handle Assembly

NOTE: The rope guide is attached to the right side of the upper

handle. Loosen the knob securing the rope guide (Figure 10).

NOTE: Vertical Storage Mowers Only: The recoil starter rope is

equipped with a rope stop clamp to prevent the starter rope

being pulled into the engine. Do not remove the rope stop clamp.

1. Hold blade control against upper handle.

2. Slowly pull recoil starter rope handle from engine and slip

starter rope into the rope guide.

3. Tighten rope guide knob.

Figure 10

Attaching the Grass Catcher (if equipped)

1. Perform the following to assemble the grass catcher

(Figure 11).

NOTE: Before assembling the grass catcher, ensure the grass

bag is turned right side out, with the warning label showing

on the outside.

a. Place bag over frame so that its black plastic side is at the

bottom.

b. Slip plastic channels (a) of grass bag over the frame (b).

Figure 11

2. Follow steps below to attach grass catcher (Figure 12).

a. Lift mower rear discharge door (a).

b. Place grass catcher into the slots in the handle brackets

(b). Lower the discharge door so that it rests on the grass

catcher.

NOTE: To remove grass catcher reverse STEP 2. Lift mower rear

discharge door. Lift grass catcher up and off the slots in the

handle brackets and lower the rear discharge door.

Figure 12

Attaching Side Discharge Cover (if equipped)

The mower is shipped as a mulcher. To convert to side discharge,

ensure the grass catcher is removed and the rear discharge door

is closed.

1. Lift the side mulch cover (Figure 13).

2. Slide the two hooks of the side discharge cover under the

mulch cover hinge pin. Lower the side mulch cover.

IMPORTANT: Do not remove side mulch cover at any time.

Figure 13

NOTE: Some side discharge chutes include a clip to secure the

discharge chute to the handle. If equipped, the side discharge

chute can be secured to the handle when not in use (Figure 14).

Figure 14

ADJUSTMENTS

Cutting Height Adjustment

There are two cutting height adjustment configurations. Refer to

the section applicable to your mower.

SINGLE LEVER IF EQUIPPED

The single lever cutting height adjustment is located above the

rear left wheel (Figure 15).

1. Carefully pull the height adjustment lever outward towards

wheel (mower will tend to fall when lever is moved

outward).

2. Move lever to desired position for a change in cutting height.

3. Release lever towards deck.

Lower

Higher

Figure 15

DUAL LEVER IF EQUIPPED

The dual lever cutting height adjustment levers are located

above the front and rear right wheel (Figure 16).

1. Carefully pull the height adjustment lever outward towards

wheel (mower will tend to fall when lever is moved

outward).

NOTE: The front and rear height adjustment levers move in

the opposite direction to adjust.

2. Move lever to desired position for a change in cutting height.

3. Release lever towards deck.

IMPORTANT: To avoid uneven cutting, all wheels must be placed

in the same cutting height position. For rough or uneven lawns,

move each height adjustment lever to a higher position. This will

prevent you from cutting the grass too close to the ground.

Lower

Higher

Figure 16

Handle Pitch Adjustment (If Equipped)

For convenience of operation, you may adjust the pitch of the

handle. Perform one of the following.

PULLOUT HANDLES

1. Remove two knobs or wing nuts and carriage bolts from

handle (Figure 17).

2. Position the handle in one of the three positions that is most

comfortable. See inset, Figure 17.

3. Secure into position with two knobs or wing nuts and

carriage bolts removed in STEP 1.

Knobs

Shown

Figure 17

VERTICAL STORAGE HANDLES

1. Unlock the two handle release levers. See inset, Figure 18.

2. Move the upper handle (a) to align the position indicator (b)

with the most comfortable of the three handle positions (c).

3. Lock the two handle release levers. See inset, Figure 18.

Lock

Unlock

Figure 18

OPERATION

Features

A. BLADE CONTROL

The blade control is attached to the upper handle of the mower.

Depress and squeeze it against the upper handle to operate the

mower. Release the blade control to stop blade and engine.

WARNING

This blade control is a safety device. Never attempt to

bypass its operation.

B. CUTTING HEIGHT ADJUSTMENT LEVER

There are two cutting height adjustment configurations.

1. Dual Lever - The dual lever cutting height adjustment

levers are located above the front and rear right wheels.

To adjust the cutting height, refer to Cutting Height

Adjustment on page 10.

2. Single Lever - The cutting height adjustment lever is

located above the rear left wheel. To adjust the cutting

height, refer to Cutting Height Adjustment on page 10.

Figure 19

C. RECOIL STARTER

The recoil starter is attached to the right upper handle. Standing

behind the mower and while holding the blade control down,

pull the recoil starter handle to start the mower.

D. GRASS CATCHER (IF EQUIPPED)

The grass catcher, located at the rear of the mower, is used to

collect the grass clippings for disposal. Once the bag is full,

remove it up through the handles and empty it before any

further mowing.

E. MULCH PLUG (IF EQUIPPED)

The mulch plug is located on the right side of the mower and is

used for mulching purposes (recirculating the clippings back to

the lawn).

OPERATION

F. SIDE DISCHARGE CHUTE (IF EQUIPPED)

The side discharge chute is used to discharge grass clippings to

the side of the mower instead of collecting the clippings in the

grass catcher or using the mower as a mulcher.

WARNING

Keep hands and feet away from the chute area on cutting

deck. Refer to warning label on the unit.

G. TRAIL SHIELD

The trail shield is attached to the rear of the mower and is there

to protect the operator from flying debris. Do not use the mower

unless the shield is fully functional and in place.

H. DECK WASH (IF EQUIPPED)

Your mower’s deck may be equipped with a fast attach deck

wash nozzle on its surface as part of its deck wash system. Use

the deck wash to rinse grass clippings from the deck’s underside.

I. VERTICAL STORAGE (IF EQUIPPED)

This feature allows the handle to be folded forward and the

mower tipped back and stored vertically.

WARNING

Standing a mower without the vertical storage feature in

the upright position may cause damage to the engine or

cause a fuel or oil leak.

Only mowers with the vertical storage feature include an

engine that can be stored in the upright position.

Gasoline And Oil Fill-up

IMPORTANT: Refer to the separate Engine Operator’s Manual for

additional engine information.

This mower is shipped without gasoline (fuel) or oil in the engine.

Be certain to service engine with gasoline and oil as instructed

before starting or operating your lawn mower.

1. Add provided oil before starting mower for the first time as

instructed in the separate Engine Operator’s Manual.

2. Service the engine with gasoline as instructed in the separate

Engine Operator’s Manual.

WARNING

Use extreme care when handling gasoline. Gasoline

is extremely flammable and the vapors are explosive.

Never fuel the machine indoors or while the engine is hot

or running. Extinguish cigarettes, cigars, pipes and other

sources of ignition.

To Start Engine

WARNING

Be sure no one other than the operator is standing near

the lawn mower while starting engine or operating

mower. Never run engine indoors or in enclosed, poorly

ventilated areas. Engine exhaust contains carbon

monoxide, an odorless and deadly gas. Keep hands, feet,

hair and loose clothing away from any moving parts on

engine and lawn mower.

Refer to the Engine Operator’s Manual for instructions on starting

and stopping the engine.

To Stop Engine

Release blade control to stop the engine and blade.

WARNING

Wait for the blade to stop completely before performing

any work on the mower or to remove the grass catcher.

Check blade stopping time is within 3 seconds. If blade

does not stop within 3 seconds contact your Service Center.

Using Your Lawn Mower

Be sure lawn is clear of stones, sticks, wire, or other objects which

could damage lawn mower or engine. Such objects could be

thrown by the blade in any direction and cause serious personal

injury to the operator and helpers.

WARNING

The operation of any lawn mower can result in foreign

objects being thrown into the eyes, which can damage

your eyes severely. Always wear safety glasses while

operating the mower, or while performing any

adjustments or repairs.

Using Mower as a Mulcher

For mulching grass, remove the grass catcher from the mower.

When you remove the grass catcher from the mower allow the

rear discharge door to close completely. For effective mulching,

do not cut wet grass. If the grass has been allowed to grow in

excess of four inches, mulching is not recommended. Use the

grass catcher to collect clippings instead.

OPERATION

Using Mower with Grass Catcher

You can use the grass catcher to collect clippings while you are

operating the mower.

1. Attach grass catcher following instructions in the Assembly

section. Grass clippings will automatically collect in bag.

Operate mower until grass bag is full.

2. Stop engine by releasing the blade control. Make sure that

the engine has come to a complete stop.

3. Lift rear discharge door and pull grass bag up and away from

the mower to remove the bag. Dispose of the grass clippings

and reinstall the bag when complete.

WARNING

If you strike a foreign object, stop the engine. Disconnect

the spark plug wire, thoroughly inspect mower for

any damage, and repair damage before restarting

and operating. Extensive vibration of mower during

operation is an indication of damage. The mower should

be promptly inspected and repaired.

Vertical Mower Storage (If Equipped)

WARNING

Standing a mower without the vertical storage feature in

the upright position may cause damage to the engine or

cause a fuel or oil leak.

Only mowers with the vertical storage feature include an

engine that can be stored in the upright position.

Do not store the mower outside or in damp area. Store

mower in a dry, clean area.

STORING THE MOWER

WARNING

Wait for engine to cool before wiping or storing.

IMPORTANT: Before storing the mower in the vertical position

ensure the fuel level is at or below the recommended fill level.

Refer to the Engine Operator’s Manual.

1. Using compressed air or dry rag clean the outside of the

mower and remove any debris from around the engine.

2. If equipped, remove the starting key.

3. Unlock the two handle release levers. See inset Figure 20.

4. Fold the handle (b) forward to the storage position

(Figure 20). Do not crimp blade control cable or the drive

control cable (if equipped) while lowering the handle.

5. Lock the two handle release levers. See inset Figure 20.

Unlock

Lock

Figure 20

6. Lifting from the handle (a), tilt the mower up onto the rear

wheels and back of the handle bracket (b) (Figure 21).

7. Position the mower so that the blade is facing a wall.

Figure 21

REMOVING THE MOWER FROM STORAGE

WARNING

When moving the mower or unfolding the handle do

not put hands or feet near or under the cutting deck.

Otherwise serious injury may occur.

To prevent accidentally starting the mower engine when

unfolding the handle, do not hold the blade control

against the upper handle. Otherwise serious injury may

occur.

1. Holding the mower by the upper handle, gently set the

mower down on all four wheels.

2. To unfold the handle, unlock the two handle release levers

(inset, Figure 21) and perform STEPS 5-8 in ASSEMBLY,

Vertical Storage Handle on page 8.

SERVICE AND MAINTENANCE

WARNING

Before performing any type of maintenance/service, disengage all controls and stop the engine. Wait until all moving parts

have come to a complete stop. Allow the engine to cool. Disconnect spark plug wire and ground it against the engine to

prevent unintended starting.

General Recommendations

• Always observe safety rules on the mower and in the

manual(s) when performing any maintenance.

• The warranty on this mower does not cover items that have

been subjected to operator abuse or negligence. To receive

full value from warranty, operator must maintain the mower

as instructed here.

• Changing of engine-governed speed will void engine

warranty.

• Check that all hardware is in place & secure and tight before

each use and before off season storage.

Lubrication

BLADE CONTROL

Lubricate pivot points on the blade control at least once a season

and before storage with light oil. This control must operate freely

in both directions (Figure 22).

WHEELS

Lubricate all wheel hubs/axles at least once a season and before

storage with light oil (Figure 22).

Figure 22

Engine Maintenance

Annually check the engine mounting bolts torque: Min. 29.2

ft-lbs (39.6 N-m), Max. 41.7 ft-lbs (56.3 N-m).

Refer to the Engine Operator’s Manual packed with your

mower for a detailed description of all engine-related service

specifications and storage.

If engine runs erratic, overheats, skips (hesitates) or idles poorly

refer to the Engine Operator’s Manual.

IMPORTANT: Check engine oil level before each use. Refer to

Engine Operator’s Manual.

CLEAN ENGINE

• Before every use, clean grass, chaff or accumulated debris

from engine. Keep linkage, spring, and controls clean. Keep

area around and behind muffler free of any combustible

debris.

• Keeping engine clean allows air movement around engine.

• Engine parts should be kept clean to reduce the risk of

overheating and ignition of accumulated debris.

CAUTION

Do not use water to clean engine parts. Water could

contaminate fuel system. Use a brush or dry cloth.

Mower Maintenance

DECK WASH (IF EQUIPPED)

Your mower’s deck may be equipped with a deck wash system.

Use the deck wash to rinse grass clippings from the deck’s

underside and prevent the buildup of corrosive chemicals.

Complete the following steps AFTER EACH MOWING:

1. Push the mower to a level, clear location on your lawn. Ensure

your garden hose can reach your mower.

CAUTION

Make certain the mower’s discharge chute is directed

AWAY from your house, garage, parked cars, etc.

2. Remove the fast attach deck wash nozzle from the mower

deck and thread it onto the end of your garden hose.

3. Attach garden hose with the deck wash nozzle to the water

port on your deck’s surface (Figure 23).

4. Turn the water ON.

5. Start the engine as described in the Engine Operator’s

Manual.

6. Run the engine for a minimum of two minutes, allowing the

underside of the cutting deck to thoroughly rinse.

7. Release blade control to stop the engine and blade.

8. Turn the water OFF and detach the deck wash nozzle from the

water port on your deck’s surface.

9. After cleaning your deck, restart the mower. Keep the engine

and blade running for a minimum of two minutes, allowing

the underside of the cutting deck to thoroughly dry.

Figure 23

SERVICE AND MAINTENANCE

6. Remove blade from the blade adapter for testing balance.

a. Balance the blade on a round shaft screwdriver to check.

b. Remove metal from the heavy side until it balances

evenly.

NOTE: When sharpening the blade, follow the original angle

of grind. Grind each cutting edge equally to keep the blade

balanced.

WARNING

An unbalanced blade will cause excessive vibration when

rotating at high speeds. It may cause damage to engine

and blade could break causing personal injury.

7. Lubricate the engine crankshaft and the inner surface of the

blade adapter with light oil. See inset, Figure 24.

a. Slide the blade adapter (d) onto the engine crankshaft.

b. Place the blade on the adapter such that the side of the

blade marked “Grass Side” (or with part number) faces the

ground when the mower is in the operating position.

c. Make sure that the blade is aligned and seated on the

blade adapter flanges.

8. Place blade bell support (b) on the blade (c). Align notches on

the blade bell support with small holes in blade.

9. Replace hex bolt (a) and tighten hex bolt to torque: Min. 37.5

ft-lbs (50.8 N-m), Max. 50.0 ft-lbs (67.8 N-m).

NOTE: To ensure safe operation of your mower, periodically check

the blade bolt for correct torque.

Figure 24

DECK CLEANING

At least once a season and before storage, clean the underside of

the mower deck to prevent build-up of grass clippings or other

debris.

1. Allow the engine to run until it is out of fuel. Do not attempt

to pour fuel from the engine. Disconnect spark plug wire.

Refer to Engine Operator’s Manual.

2. Turn mower on its side keeping the muffler side down and

making sure that the air filter and the carburetor are facing

up. Hold mower firmly.

3. Scrape and clean the underside of the deck with a suitable

tool. Do not spray with water.

IMPORTANT: Do not use a pressure washer or garden hose to

clean your mower. These may cause damage to bearings or

the engine. The use of water will result in shortened life and

reduce serviceability.

4. Put the mower back on its wheels on the ground.

Blade Care

WARNING

Wait for the blade to stop completely before performing

any work on the mower or to remove the grass catcher.

Check blade stopping time is within 3 seconds. If blade

does not stop within 3 seconds contact your Service Center.

WARNING

When removing the cutting blade for sharpening or

replacement, protect your hands with a pair of heavy

gloves or use a heavy rag to hold the blade.

Annually check the mower blade mounting bolt torque: Min. 37.5

ft-lbs (50.8 N-m), Max. 50.0 ft-lbs (67.8 N-m).

Periodically inspect the blade and blade adapter for bends or

cracks, especially if you strike a foreign object or experience

excessive vibration. Replace when necessary. Follow the steps

below for blade service:

1. Allow the engine to run until it is out of fuel. Do not attempt

to pour fuel from the engine.

2. Disconnect spark plug wire. Refer to Engine Operator’s

Manual.

3. Turn mower on its side keeping the muffler side down and

making sure that the air filter and the carburetor are facing

up.

4. Remove bolt (a) and blade bell support (b) which hold the

blade and the blade adapter to the engine crankshaft

(Figure 24).

5. Remove blade (c) and blade adapter (d) from the crankshaft

(Figure 24).

NOTA: Este Manual del Operador corresponde a varios modelos. Las características pueden variar según los modelos.

No todas las características que se incluyen en este manual se aplican a todos los modelos y el modelo que se ilustra aquí

puede diferir del suyo.

Manual del OperadOr

Prácticas de Operación Seguras • Montaje • Funcionamiento • Servicio y Mantenimiento

Cortadora de Césped de Empuje

ADVERTENCIA

Lea y cumpla todas las reglas e instrucciones de seguridad de este manual antes de intentar operar

esta máquina.

Si no sigue estas instrucciones, se pueden provocar lesiones personales - GUARDE ESTAS

INSTRUCCIONES.

ADVERTENCIA

PROPOSICIÓN 65 DE CALIFORNIA

El escape del motor, algunos de los elementos del mismo y algunos componentes del vehículo

contienen o liberan sustancias químicas que según el Estado de California pueden producir cáncer,

defectos de nacimiento u otros problemas reproductivos.

Registro de Información del Producto

Antes de configurar y hacer funcionar su nueva

cortadora de césped, por favor localice la placa

de modelo en el equipo y registre la información

en el espacio de la derecha. Encontrará la

placa de modelo parándose en la posición del

operador y mirando sobre la parte posterior de

la plataforma. Necesitará esta información si

tiene que solicitar soporte técnico a través de

nuestro sitio web, el Departamento de Atención

al Cliente, o de un distribuidor local de servicio

autorizado.

Número de modelo

Número de serie

PRÁCTICAS DE OPERACIÓN SEGURAS

INFORMACIÓN GENERAL

1. Lea, entienda y cumpla todas las instrucciones que figuran

sobre la cortadora de césped y en los manuales antes de

intentar armar la unidad y utilizarla. Guarde este manual en un

lugar seguro para consultas futuras y periódicas, así como para

solicitar repuestos.

2. Familiarícese con todos los controles y con el uso adecuado de

los mismos.

3. No permita nunca que los niños menores de 14 años utilicen

esta cortadora de césped. Los niños de 14 años en adelante

deben leer y entender las instrucciones y prácticas de operación

seguras contenidas en este manual y sobre la cortadora de

césped, y deben ser entrenados y supervisados por un adulto.

4. Nunca permita que los adultos operen esta cortadora de césped

sin recibir antes la instrucción apropiada.

5. Almacene la cortadora en una zona limpia y seca. No la

almacene cerca de productos corrosivos, como por ejemplo

fertilizantes.

6. Si se presentan situaciones que no están previstas en este

manual, sea cuidadoso y use el sentido común. Póngase en

contacto con su representante de atención al cliente para

obtener ayuda.

7. De conformidad con la Comisión de Seguridad de Productos

para el Consumidor de los Estados Unidos (CPSC) y la Agencia

de Protección Ambiental de los Estados Unidos (EPA), este

producto tiene una vida útil estimada de siete (7) años, en

condiciones normales de uso. Al final de su vida útil, se deberá

solicitar una inspección del producto anualmente a fin de

asegurarse de que todos los sistemas mecánicos y de seguridad

funcionen adecuadamente, de manera segura y no estén

excesivamente desgastados. Si no lo hace, puede ocasionar

accidentes, lesiones o la muerte.

PREPARATIVOS ANTERIORES AL USO

1. Revise minuciosamente el área donde se va a usar la cortadora

de césped. Saque todas las piedras, palos, cables, huesos,

juguetes y otros objetos extraños con los que podría tropezar o

que podrían ser arrojados por la cuchilla. Los objetos arrojados

por la máquina pueden producir lesiones personales graves.

2. Para evitar lesiones por contacto con la cuchilla o un objeto

arrojado, permanezca en la zona del operador detrás de

las manijas de la cortadora. Indique a los asistentes que

permanezcan al menos a 75 pies (23 metros) de la cortadora

mientras está en funcionamiento. Mantenga a observadores,

niños y mascotas en interiores durante el funcionamiento de la

cortadora de césped. Detenga la cortadora de césped si alguien

entra en la zona.

3. Esté atento a la cortadora de césped y a la dirección de descarga

de los aditamentos y no apunte la descarga de la cortadora en

dirección a nadie.

4. Para protegerse los ojos, utilice siempre gafas o anteojos de

seguridad mientras opera la máquina y mientras la ajusta o

repara. Los objetos arrojados que rebotan pueden producir

lesiones graves en los ojos.

5. Utilice zapatos de trabajo resistentes, de suela fuerte, y

pantalones y camisas ajustados. Las ropas sueltas, las alhajas y

el cabello largo pueden engancharse en las piezas móviles. Se

recomienda vestir camisas y pantalones que cubren brazos y

piernas y usar zapatos con puntera de acero.

6. Nunca opere la cortadora descalzo, con sandalias, zapatos

resbalosos o livianos (por ej. de lona).

7. Nunca llene en exceso el depósito de combustible. Llene el

depósito no más de 1” (2.5 cm) por debajo de la base del cuello

de llenado dejando espacio para la expansión del combustible.

8. Vuelva a colocar la tapa de la gasolina y ajústela bien.

9. Use sólo implementos y accesorios que el fabricante haya

aprobado para esta cortadora de césped. Lea, comprenda y siga

todas las instrucciones incluidas con el accesorio o implemento

aprobado.

FUNCIONAMIENTO

1. Las estadísticas indican que los operadores mayores de 65

años se ven involucrados en un alto porcentaje de lesiones

relacionadas con cortadoras de césped. Estas personas deben

evaluar su capacidad para operar la cortadora de césped de

manera suficientemente segura para protegerse a sí mismos y a

otros de lesiones graves.

2. Muchas lesiones ocurren como resultado de pasar la cortadora

sobre los pies durante una caída provocada al patinarse o

tropezarse. No se sostenga de la cortadora si se está cayendo,

suelte la manija inmediatamente.

3. Nunca tire la cortadora hacia usted mientras camina. Si debe

retroceder con la cortadora para evitar una pared u obstáculo,

mire primero abajo y atrás para evitar tropezarse y luego siga

estos pasos:

ADVERTENCIA

Este símbolo indica instrucciones de seguridad importantes que, de no seguirse, pueden poner en peligro su

seguridad personal y/o material y la de otras personas. Lea y cumpla todas las instrucciones de este manual

antes de intentar hacer funcionar esta máquina. Si no sigue estas instrucciones, se pueden provocar lesiones

personales.Cuando vea este símbolo, ¡PRESTE ATENCIÓN A LA ADVERTENCIA!

PELIGRO

Esta máquina está diseñada para ser utilizada respetando las prácticas de operación seguras contenidas en este manual. Al

igual que con cualquier tipo de equipo motorizado, un descuido o error por parte del operador puede producir lesiones graves.

Esta máquina es capaz de amputar dedos, manos y pies y de arrojar residuos. De no respetar las instrucciones de seguridad

siguientes, se pueden ocasionar lesiones graves o la muerte.

PRÁCTICAS DE OPERACIÓN SEGURAS

a. Apártese de la cortadora hasta estirar completamente sus

brazos.

b. Asegúrese de estar en equilibrio y bien parado.

c. Tire de la cortadora lentamente hacia usted, no más allá de

la mitad de la distancia que los separa.

d. Repita estos pasos según sea necesario.

4. No engrane el control de la transmisión (si se incluye) mientras

enciende el motor.

5. El control de la cuchilla es un dispositivo de seguridad. Nunca

intente anular su funcionamiento. De hacerlo, el dispositivo de

seguridad quedaría inoperativo y podrían producirse lesiones

personales por el contacto con la cuchilla giratoria. El control de

la cuchilla debe funcionar bien en ambas direcciones y regresar

automáticamente a la posición desengranada cuando se lo

suelta. La cuchilla continúa rotando por hasta tres segundos

después de que se suelta el control de las cuchillas. Nunca

coloque ninguna parte del cuerpo en el área de la cuchilla hasta

que esté seguro que la cuchilla ha dejado de girar.

6. Si la cortadora de césped comienza a vibrar de forma extraña,

detenga el motor y busque inmediatamente la causa. La

vibración generalmente advierte que hay algún problema.

7. Nunca opere la cortadora sin estar en su lugar y funcionando

el escudo apropiado, la cubierta de descarga, el colector

de césped, el control de la cuchilla u otros dispositivos de

seguridad y protección. Nunca opere la cortadora si los

dispositivos de seguridad están dañados. De lo contrario

podrían producirse lesiones personales.

8. Cuando encienda el motor, jale de la cuerda lentamente hasta

que sienta resistencia, luego jale rápidamente. El repliegue

rápido de la cuerda de arranque (retroceso o rebote) le jalará

la mano y el brazo hacia el motor más rápido de lo que usted

tarda en soltarla. Puede llegar a causar huesos rotos, fracturas,

hematomas y esguinces.

9. No ponga las manos ni los pies cerca de las piezas rotatorias

ni debajo de la plataforma de corte. El contacto con la(s)

cuchilla(s) puede amputar manos y pies.

10. Esté atento a los hoyos, surcos, baches, rocas, u otros objetos

ocultos. Los terrenos desnivelados u objetos ocultos pueden

causar derrapes y/o caídas. El césped alto puede ocultar

obstáculos.

11. La cortadora está diseñada para cortar césped residencial

normal, con una altura no mayor a 7” (17.5 cm). No intente

cortar césped demasiado crecido, seco (como un pastizal) ni

pilas de hojas secas.

12. Planifique el patrón de corte para evitar que la descarga de

material se realice hacia caminos, veredas, asistentes, etc. Evite

descargar material contra una pared u obstrucción, ya que

esto podría hacer que el material descargado rebote contra el

operador.

13. Apague el motor y espere hasta que la cuchilla se detenga

completamente antes de retirar el colector de césped o de

destapar la tolva. La cuchilla de corte sigue girando por hasta

tres segundos después de soltar el control de la cuchilla. Nunca

coloque ninguna parte del cuerpo en el área de la cuchilla hasta

que esté seguro de que el motor está apagado y la cuchilla ha

dejado de girar.

14. Una puerta de descarga, tolva o adaptador para abono faltante

o dañado puede provocar lesiones por contacto con la cuchilla o

por objetos arrojados.

15. Nunca opere la cortadora de césped si no están bien colocados

la puerta de descarga, la tolva, el adaptador para abono o el

colector de césped completo.

16. Detenga la cuchilla de la cortadora de césped cuando cruce

caminos o senderos de gravilla y cuando no esté cortando el

césped.

17. Corte el césped solamente con luz de día o con una buena luz

artificial.

18. No opere la cortadora de césped estando bajo los efectos del

alcohol o de drogas.

19. El silenciador y el motor están a temperatura muy alta y pueden

provocar lesiones graves por quemaduras. No los toque. Deje

que se enfríe la cortadora de césped al menos durante cinco

minutos antes de almacenarla o intentar cualquier tarea de

mantenimiento.

20. Nunca encienda un motor en interiores o en espacios cerrados o

con poca ventilación. El escape del motor contiene monóxido de

carbono, un gas inodoro y letal.

NIÑOS

1. Si el operador no está atento a la presencia de niños, se pueden

producir accidentes trágicos. Por lo general a los niños les

atraen las cortadoras y la actividad de cortar el césped. Los

niños no son conscientes de los peligros. Nunca asuma que los

niños permanecerán donde los vio por última vez.

2. Mientras la cortadora está en funcionamiento, mantenga a

observadores, niños y mascotas en interiores bajo la atenta

supervisión de un adulto responsable que no sea el operador.

Detenga la cortadora de césped si alguien entra en la zona.

3. Esté alerta y apague la cortadora si un niño u observador

ingresa al área.

4. No permita nunca que los niños menores de 14 años utilicen

esta cortadora de césped. Los niños de 14 años en adelante

deben leer y entender las instrucciones y prácticas de operación

seguras contenidas en este manual y sobre la cortadora de

césped, y deben ser entrenados y supervisados por un adulto.

5. Esta cortadora de césped es un equipo motorizado de precisión,

no un juguete. Por lo tanto, tenga mucho cuidado en todo

momento. Esta cortadora de césped fue diseñada para realizar

una sola tarea: cortar el césped. No la utilice para ningún otro

fin.

6. Tenga mucho cuidado al aproximarse a esquinas ciegas,

puertas, arbustos, árboles u otros objetos que puedan

obstaculizarle la vista de un niño que pudiese correr al

encuentro de la cortadora.

7. Mantenga a los niños alejados de motores en marcha o

calientes. Pueden sufrir quemaduras al tocar un motor o

silenciador caliente.

8. Si su cortadora de césped viene equipada con una Llave

Pulsadora de Encendido Eléctrico, quite la llave cuando deje

sola la cortadora para evitar que una persona sin autorización

la maneje. Asegúrese de que la llave quede fuera del alcance de

niños pequeños.

PRÁCTICAS DE OPERACIÓN SEGURAS

FUNCIONAMIENTO EN PENDIENTES PARA CORTADORAS

DE EMPUJE

1. Las pendientes son un factor importante en los accidentes

ocasionados por derrapes y caídas y pueden producir lesiones

graves o incluso la muerte. Todas las pendientes requieren

precaución extra. Si no se siente seguro en una pendiente, no

corte el césped.

2. Para su seguridad, antes de usar la cortadora de césped mida

cualquier pendiente que haya. Use un dispositivo de medición

de pendientes además del indicador de pendiente que se

incluye como parte de este manual para medir las pendientes

antes de operar esta cortadora de césped en una zona inclinada

o con pendientes. Para medir las pendientes, también se

pueden usar aplicaciones de teléfonos inteligentes. Si la

pendiente es de más de 15º (25%) medida por el indicador de

pendiente o un dispositivo de medición de pendientes, no haga

funcionar esta cortadora de césped en ese sector pues podría

causar lesiones graves.

3. No corte el césped en pendientes de más de 15 grados (25%).

4. Siempre corte el césped de forma transversal a la pendiente,

nunca hacia arriba y hacia abajo.

5. La cortadora de césped podría acelerarse al colocarla cuesta

abajo, siempre debe colocarla cuesta arriba. Mantenga siempre

el control de la cortadora de césped.

6. No corte el césped húmedo. Si no está firmemente parado,

podría resbalarse.

7. No opere la cortadora de césped en ninguna condición en la que

se comprometan la tracción o estabilidad. Asegúrese siempre

de estar bien afirmado. Si resbala y cae puede lesionarse

gravemente. Si siente que pierde el equilibrio o deja de estar

bien afirmado, suelte inmediatamente la manija de control de

la cuchilla y la cuchilla dejará de girar en tres (3) segundos.

8. Manténgase a por lo menos 3 pies (1 metro) de barrancos,

zanjas o terraplenes o del borde del agua. Podría perder el

equilibrio o dejar de estar bien afirmado.

INCENDIOS Y COMBUSTIBLE

1. Sea sumamente cuidadoso al manipular gasolina para

evitar lesiones personales y daños materiales. La gasolina es

sumamente inflamable y sus vapores son explosivos. Si se

derrama gasolina encima o sobre la ropa se puede lesionar

gravemente ya que se podría prender fuego. Lávese la piel y

cámbiese de ropa de inmediato.

2. Apague todos los cigarrillos, cigarros, pipas y otras fuentes de

encendido.

3. Use sólo un recipiente de combustible (gasolina) portátil

aprobado. Use sólo recipientes certificados por EPA, CARB y/u

OSHA.

4. Nunca saque la tapa del combustible ni agregue combustible

mientras el motor está caliente o en marcha. Deje que el motor

se enfríe por lo menos cinco minutos antes de volver a cargar

combustible.

5. Nunca cargue combustible a la cortadora de césped en

interiores.

6. Nunca guarde la cortadora de césped o el recipiente de

combustible en un espacio cerrado donde haya una llama

abierta, chispas o luz piloto, como por ejemplo de calentadores

de agua, calefactores de ambientes, hornos, secadores de ropa

u otros aparatos a gas.

7. Limpie el combustible que se pueda haber derramado sobre

el motor y la cortadora de césped. Limpie los derrames de

combustible o aceite y elimine los residuos empapados con

gasolina. Traslade la cortadora de césped a otra zona. Espere al

menos 5 minutos antes de arrancar el motor.

8. Para reducir el riesgo de incendio mantenga la cortadora limpia

de pasto, hojas y de acumulación de otros escombros. Siga el

“Programa de Mantenimiento” que figura en la sección Servicio

y Mantenimiento para mantener su cortadora de césped libre

de residuos.

9. Nunca llene en exceso el depósito de combustible. Llene el

depósito no más de 1” (25 mm) por debajo de la base del

cuello de llenado, para dejar espacio para la expansión del

combustible.

10. Vuelva a colocar la tapa de la gasolina y ajústela bien.

11. Deje que la cortadora de césped se enfríe por lo menos cinco

minutos antes de cargarle combustible o guardarla.

12. Nunca llene los recipientes en el interior de un vehículo o

camión o caja de remolque con recubrimientos plásticos.

Siempre ubique los recipientes en el piso, lejos del vehículo

antes de llenarlos.

13. Cuando sea factible, retire el equipo a gasolina del camión

o remolque y apóyelo en el suelo para llenarlo. Si esto no

es posible, recargue combustible sobre el remolque con un

recipiente portátil, en lugar de una boquilla dosificadora de

gasolina.

14. Mantenga la boquilla dispensadora en contacto con el borde del

depósito de combustible o con la boca del recipiente en todo

momento, hasta terminar de cargar. No utilice un dispositivo de

bloqueo/apertura de boquilla.

SERVICIO Y MANTENIMIENTO

1. Mantenga la cortadora de césped en buenas condiciones de

funcionamiento. Reemplace las piezas dañadas o gastadas.

2. Para evitar lesiones graves o la muerte, no modifique el motor

de ninguna manera. Si cambia la configuración del regulador,

el motor podría funcionar a velocidades inseguras. Nunca

modifique el ajuste de fábrica del regulador del motor. No

cambie la configuración del regulador del motor ni acelere

demasiado el motor. El regulador del motor controla la

velocidad máxima segura de funcionamiento del motor.

3. Las cuchillas de las cortadoras de césped son filosas. Envuelva la

cuchilla o utilice guantes y extreme las precauciones cuando les

haga mantenimiento.

4. Antes de limpiar, reparar o inspeccionar la máquina, compruebe

que la cuchilla y todas las partes móviles se hayan detenido.

Desconecte el cable de la bujía y póngalo de manera que

haga masa contra el motor para evitar que se encienda

accidentalmente.

5. Verifique que la cuchilla se haya detenido por completo dentro

de los tres (3) segundos de operar el control de la cuchilla.

Si la cuchilla no se detiene en menos de tres segundos, su

cortadora de césped debe ser revisada por profesionales de un

distribuidor de servicio autorizado. Consulte el funcionamiento

correcto en la sección Servicio y Mantenimiento.

PRÁCTICAS DE OPERACIÓN SEGURAS

6. Controle periódicamente el funcionamiento del sistema de

enclavamiento de seguridad, tal como se describe más adelante

en este manual. Si el sistema de enclavamiento de seguridad no

funciona correctamente, lleve su cortadora de césped a hacerle

un servicio profesional de un distribuidor autorizado.

7. Nunca altere el enclavamiento de seguridad del control

de la cuchilla u otros dispositivos de seguridad. Consulte

el funcionamiento correcto en la sección Servicio y

Mantenimiento.

8. Controle el par de ajuste del perno de montaje del motor y

cuchilla de la cortadora de césped de acuerdo con la sección

Servicio y Mantenimiento de este manual. Además, inspeccione

visualmente la cuchilla en busca de daños (por ejemplo,

desgaste excesivo, abolladuras, rajaduras). Reemplace la

cuchilla únicamente por la cuchilla del fabricante del equipo

original (O.E.M.)

9. El uso de piezas que no cumplen con las especificaciones del

equipo original puede resultar en un rendimiento inadecuado y

poner en peligro la seguridad.

10. Mantenga todas las tuercas, pernos y tornillos bien ajustados

para asegurarse de que la máquina se en

11. uentra en condiciones de funcionamiento seguras. Controle el

ajuste de todos los elementos de ferretería de acuerdo con la

sección Servicio y Mantenimiento.

12. Después de golpear contra algún objeto extraño, detenga el

motor, desconecte el(los) cable(s) de bujía y conecte el motor

a masa. Inspeccione minuciosamente la cortadora de césped

para determinar si está dañada. Repare el daño antes de volver

a arrancar y operar la máquina.

13. Nunca intente ajustar una rueda o la altura de corte ni efectuar

reparaciones mientras el motor está en marcha.

14. Los componentes del colector de césped y la cubierta de

descarga están sujetos a desgaste y daños que podrían dejar

expuestas piezas que se mueven o permitir que se arrojen

objetos. Para proteger su seguridad, verifique frecuentemente

los componentes y reemplácelos inmediatamente por piezas

del fabricante del equipo original (O.E.M.) únicamente. “El uso

de piezas que no cumplen con las especificaciones del equipo

original podría producir un rendimiento inadecuado y además

puede comprometer la seguridad”.

15. Mantenga o reemplace las etiquetas de seguridad e

instrucciones según sea necesario.

16. Respete las leyes y reglamentaciones referentes a la

eliminación correcta de combustible, aceite, etc. para proteger

el medio ambiente.

AVISO SOBRE EMISIONES

Los motores tienen la certificación de cumplimiento de

las reglamentaciones sobre emisiones federales de EPA

y California para SORE (equipo pequeño para uso fuera

de carreteras), funcionan con gasolina normal sin plomo

y pueden incluir los siguientes sistemas de control de

emisiones: Modificación de motor (EM) y catalizador de tres

vías (TWC) si están equipados con esos sistemas.

Cuando sea necesario, los modelos están equipados con

líneas de combustible y depósitos de combustible de baja

penetración para controlar las emisiones por evaporación.

Los modelos de California también pueden incluir un filtro

de carbono. Por favor, póngase en contacto con Atención

al Cliente para obtener información sobre la configuración

del control de emisiones por evaporación para su modelo.

AMORTIGUADOR DE CHISPAS

ADVERTENCIA

Esta cortadora de césped está equipada con un motor de

combustión interna y no debe ser utilizada en o cerca de

un terreno agreste cubierto por bosque, malezas o hierba

a manos que el sistema de escape del motor esté equipado

con un amortiguador de chispas que cumpla con las leyes

locales o estatales correspondientes (en caso de existir).

Si se utiliza un amortiguador de chispas, el operador

lo debe mantener en condiciones de uso adecuadas.

En el Estado de California, las medidas anteriormente

mencionadas son exigidas por ley (Artículo 4442 del Código

de Recursos Públicos de California). Es posible que existan

leyes similares en otros estados. Las leyes federales se

aplican en territorios federales.

Puede conseguir el amortiguador de chispas para el

silenciador a través de su distribuidor autorizado de

motores más cercano o poniéndose en contacto con el

departamento de servicios, P.O. Box 361131 Cleveland, Ohio

44136-0019.

INDICADOR DE PENDIENTE (CUBIERTA POSTERIOR)

ADVERTENCIA

Las pendientes son un factor importante en los accidentes

ocasionados por derrapes y caídas y pueden producir

lesiones graves. Todas las pendientes requieren precaución

extra. Si no se siente seguro en una pendiente, no corte

el césped. No corte el césped en pendientes de más de 15

grados (25%). Siempre corte el césped de forma transversal

a la pendiente, nunca hacia arriba y hacia abajo.

PARA DETERMINAR SI UNA PENDIENTE ES DEMASIADO

EMPINADA Y EVITAR RIESGOS, USE EL INDICADOR DE

PENDIENTE QUE APARECE EN LA CUBIERTA POSTERIOR COMO

SE MUESTRA.

Para comprobar la pendiente, proceda de la siguiente

manera:

1. Abra el manual en la página y dóblela por la línea de puntos.

2. Ubique un objeto vertical que esté sobre la pendiente o detrás

de la misma (p. ej., un poste, un edificio, un cerco, un árbol, etc.)

3. Alinee cualquiera de los lados del indicador de pendiente con

el objeto.

4. Ajuste el indicador hacia arriba o abajo hasta que la esquina

izquierda toque la pendiente.

5. Si hay una separación por debajo del indicador, significa que la

pendiente es demasiado empinada para una operación segura.

La page charge ...

Cub Cadet 11AB9M5710 Le manuel du propriétaire

Marque: Cub Cadet

Modèle: 11AB9M5710

Catégorie: Tondeuses à gazon

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Cub Cadet 11AB9M5710 Owner's manual
español: Cub Cadet 11AB9M5710 El manual del propietario

Cub Cadet 11AB9M5710 Le manuel du propriétaire

Cub Cadet 11AB9M5710 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents