SportsArt E850 Le manuel du propriétaire

Marque: SportsArt

Modèle: E850

Taper: Le manuel du propriétaire

E850 OWNER’S MANUAL CONTENTS

1. INTRODUCTION .............................................................................. 2

2. SAFETY PRECAUTIONS ................................................................ 3

3. LIST OF PARTS ............................................................................... 5

4. ASSEMBLE THE PRODUCT ........................................................... 7

STEP 1 Unbox the Unit ........................................................................ 7

STEP 2 Assemble the Pedestal............................................................ 8

STEP 3 Install the Upper Cover............................................................ 9

STEP 4 Install Stride Linkages and Footplate Carriages. .................... 9

STEP 5 Install Left/Right Supports ....................................................... 10

STEP 6 Secure the Rail Base Cover ................................................... 11

STEP 7 Move the Unit into Place ......................................................... 12

STEP 8 Level the Unit .......................................................................... 13

STEP 9 Ground Wire Connection ........................................................ 14

STEP 10 Avoid Safety Hazards ............................................................ 14

5. MECHANICAL ADJUSTMENTS ...................................................... 15

6. UNDERSTAND THE E850 DISPLAY ............................................... 16

DISPLAY Overview .............................................................................. 16

DISPLAY Windows ............................................................................... 17

DISPLAY Keys ..................................................................................... 17

DISPLAY Specications ....................................................................... 18

7. OPERATE THE E850 ELLIPTICAL TRAINER ................................. 18

OPERATION QUICK START Mode ..................................................... 18

OPERATION START Mode .................................................................. 19

OPERATION Cool Down ...................................................................... 21

OPERATION Workout Programs ......................................................... 21

OPERATION User Preferences and Product Information .................... 23

8. ABOUT HEART RATE DETECTION ................................................ 25

HEART RATE Telemetry ...................................................................... 25

HEART RATE Contact ......................................................................... 25

9. GUIDELINES FOR EXERCISE ........................................................ 26

10. MAINTENANCE ............................................................................. 27

MAINTENANCE Lubricate the Shoulder Area ..................................... 27

MAINTENANCE Clean the Glide Rail .................................................. 28

MAINTENANCE Schedule ................................................................... 29

MAINTENANCE Task List (Elliptical Trainers) ..................................... 30

MAINTENANCE One-Year Maintenance Log ...................................... 31

MAINTENANCE Electronics Block Diagram ........................................ 32

11. SAFETY PRECAUTIONS IN FRENCH .......................................... 33

1. INTRODUCTION

Congratulations on your purchase of one of the nest exercise products on the market

today, the SportsArt E850 elliptical trainer. Constructed of high quality materials and

designed for years of reliable usage, this product was made to become an integral

part of your commercial tness venue.

Before this product is assembled or operated, we recommend that you famil-

iarize yourself with this manual. Understanding the correct methods of assembly

and operation will help ensure that exercisers obtain their tness goals safely and

successfully.

2. SAFETY PRECAUTIONS

This product was designed and built for optimum safety. However certain precau-

tions apply during the use of this product. Please note the following safety

precautions:

• Please read the entire manual before assembly and operation. Make

sure the product is installed and operated as instructed in this manual.

• Assemble and operate the product on a solid, level surface. Do not use

outdoors or near water, including pools and saunas.

• Check the product before every use. Make sure all parts are assem-

bled, and all fasteners are tightened. Do not use the product if it is disas-

sembled in any way.

• Wear proper workout clothing. Do not wear loose clothing. Do not wear

shoes with leather soles or high heels. Tie all long hair back. Do not go

barefoot on this product.

• Keep away from moving parts. Moving parts may or may not stop imme-

diately if an object becomes caught or impedes normal motion.

• Use this product only for its intended purpose as described in this

manual.

• Be careful when mounting and dismounting the unit.

• Never operate this product if it has been damaged in any way. If it is

not working properly, or has been dropped or damaged, contact a service

technician for repairs.

• Do not use accessories that are not specically recommended by the

manufacturer. Such parts might cause injuries or cause the unit to fail.

• Keep all air ventilation areas free of blockage. Never drop or insert any

object into any opening.

• Do not operate where aerosol (spray) products are being used or where

oxygen is being administered.

• This product is not intended for use by persons (including children) with

reduced physical, sensory, or mental capabilities, or by people who are

otherwise decient in product knowlege or experience. If such people use

this product, they should be given training and be supervised at all times

by someone responsible for their safety.

• Children should be supervised to ensure that they do not play on or

near the product.

• The user weight limit for this product is 180 kg, 400 lb. At maximum

resistance, level 20, this product meets standards for users up to 150 kg,

330 lb.

CAUTION: If you feel any pain or abnormal sensations, STOP YOUR

WORKOUT and consult your physician immediately. Work within your

recommended exercise level. DO NOT work to exhaustion. Before beginning

any exercise program, you should consult with your doctor. It is recommended that

you undergo a complete physical examination.

WARNING! Heart rate monitoring systems may be inaccurate. Too much exercise

may result in serious injury or death. If you feel faint, stop exercising immediately.

2. SAFETY PRECAUTIONS (CONTINUED)

Note: This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential instal-

lation. This equipment generates, uses and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that inter-

ference will not occur in a particular installation. If the user desires to correct the

interference, it is at the user’s own expense.

WARNING! Only qualied technicians should be allowed to contact electrical

components such as circuit boards. Some components carry an electrical charge

even after use has been discontinued or the product has been unplugged. For

products with power cords, turn off unit power, wait ve minutes, then disconnect

the power cord from the power socket. For products without power cords, let the unit

sit without use for ve minutes. Only after taking such precautions should covers be

removed and electrical components be accessed.

3. LIST OF PARTS

Assembly Parts

No. Name Qty. No. Name Qty.

A1 Main body 1 A6 Left footplate assembly 1

A1A Rail base cover 1 A7 Right footplate assembly 1

Small cover

1 A8

Base covers for right

support

A3 Upper cover 1 A9 Base covers for left support 1

A4 Right support 1 A10 Hardware kit 1

A5 Left support 1

Components on the Product

No. Name Specication Notes

Inner hex screw M8*L20

Spring washer M8

Serrated washer D18*d8.5*t2.0*19T

42 Mushroom top Phillips screw M4*L16

Inner hex screw M8*L25

Spring washer M8

Washer D17*d8.3*t1.0

Inner hex screw M6*L15

Serrated washer D20*d6.2*t2.0*19T

Inner hex screw 5/16”*L2-1/4 inch

Seat roller washer D17*d8*t2.0

Roller axle

Flat washer D21*d10.5*t2

Lock nut M10

PU sheath D12*D8*L45

Axle M5*L71

Flat washer D17*d8.3*t1

Mushroom top inner hex screw M5*6

Components in the Hardware Kit

No. Name Qty. Specication Notes

33 Mushroom top Phillips screw 6 M4*L16

34 Phillips screw 4 M5*P0.8*L10

35 Left/right adjustment rod cover 2

36 Screw insert 4

37 M10 nut cap 2

38 Screw cap 2

L-shaped Allen wrench 1 M6

L-shaped Allen wrench 2 M4

Double open-end wrench 1 8*17

Double open-end wrench 1 13*19

T-shaped Allen wrench 1 M5

Screwdriver shank 1 at and Phillips

Screwdriver handle 1 green

4. ASSEMBLE THE PRODUCT

Follow instructions below to assemble this product. Note that in this manual

the words “left” and “right” are used to refer to the product and its parts. As

such, these designations correspond to the “left” and “right” sides of a person

in position to exercise on this product. Also, for brevity, the word “screws” is

used where screws, washers, and other hardware may be involved.

STEP 1 Unbox the Unit

Please follow instructions A through D to remove packaging material and to

place the unit on top of the flattened cardboard.

A. Remove the box top and the plastic sheet.

B. Start working from above, first removing Styrofoam (2) above the unit.

C. Lift Styrofoam (3) on both sides of the unit upward to remove it. Place

parts aside separately.

D. Lift the pedestal to remove the Styrofoam (1) in the middle.

STEP 2 Assemble the Pedestal

Please follow instructions

(a) through (b) to assemble

the pedestal.

(a) First, remove screws

(41) from the pedestal

mount on the main body

(A1).

(b) Push the pedestal up to

the vertical position while

preventing the data cable

from getting pinched.

in area (A), then in area

(B).

STEP 3 Install the Upper Cover

Please follow instructions (a) through (d) to install the upper cover.

(a) Slide the water guard up the pedestal. (This ring must be placed above

the upper cover.)

(b) Install the

upper cover and

secure it with

screw (33).

small cover (A2)

and secure it with

screw (33).

(d) Slide the water

guard down the

pedestal until it

fits snugly against

the covers.

STEP 4 Install Stride Linkages and Footplate Carriages

Please follow steps (a) through (f) to install stride linkages and footplate

carriages on both sides of the product.

(a) Remove bolts (45) from the bushing on the stride adjustment mechanism.

(b) Align the hole in the stride linkage with the bushing on the stride adjustment

mechanism, and

press the stride

linkage into place

on the bushing.

Secure the stride

linkage with bolts

(45). Then insert

the stride linkage

cover (35) into

place. Follow the

same procedure

on both sides.

(46) from the

vertical arms on

both sides.

(d) Remove

screws (47) from

the left footplate

carriage (A6).

STEP 5 Install Left/Right Supports

Please follow

instructions (a) through

(f) to install left and

right supports.

(a) Remove screws and

remove covers from the

top of the left and right

supports.

(b) Remove screws (43)

(44) from both sides.

supports (A4,A5) into

place and loosely

secure screws (43) at

the top. Do not fully

secure these screws

yet.

(d) First, secure screws

(44) at the base of the

supports (A4,A5). Then

go back to the top and

secure screws (43).

STEP 4 Install Linkages/Carriages (Continued)

(e) Insert the front of the footplate carriage into

the vertical arm. Align it with the hole and use

bolt (46) to secure it into place. Then insert caps

(37, 38) into place.

(f). Lubricate the area where the rod contacts

the bushing, hold the footplate carriage into

place, and secure it with screw (47). Perform

the same actions on both sides of the product.

STEP 6 Secure the Rail Base Cover

Please follow instructions (a) through

(b) to install the rail base cover.

(a) First, insert screw inserts (36) into

the rail base plate.

(b) Set the rail base cover (A1A) in

place and secure it with screws (33).

STEP 5 Install Left/Right Supports (Continued)

(e) Put support base covers (A8,A9)

into place on both supports (A4,A5),

and secure them with screws (34).

(f) Set upper covers into place on

both supports, and secure them with

screws (42).

STEP 7 Move the Unit into Place

Follow steps (a) through (c) to move the unit into place for use.

(a) Stand behind the unit. Grasp the glide track rods as shown.

(b) Lift up. (To avoid injury, always use proper lifting techniques.)

STEP 8 Level the Unit

If the unit does not rest flat on the floor, please follow steps (a) through (b)

to level it.

(a) Under the front of the unit, rotate the leveler nut upward to enable

adjustment of the leveler foot. Then screw the leveler foot downward until it

touches the floor. Rotate the leveler nut against the product frame to secure

this position. Carry out these instructions on both sides of the product.

(b) Under the support, rotate the leveler nut upward to enable adjustment of

the leveler foot. Then screw the leveler foot downward until it touches the

floor. Rotate the leveler nut against the product frame to secure this position.

STEP 10 Avoid Safety Hazards

While the product is in use, be careful to avoid getting pinched by or wedged

against moving parts. In particular, do not insert fingers or other body parts

into the stride adjustment area or the opening in the front covers. Prevent

injuries to yourself and others by employing safe operating practices at all

times.

STEP 9 Ground Wire Connection

The ground wire and

the following instructions

are required to meet

European safety

regulations. The ground

wire is not required in

North America.

Overview: To prevent

electrical shock and

current leakage, a ground

wire is provided in the

packaging of this product.

For your safety, connect

this ground wire to the unit

and the building ground.

Installation procedure:

First use a screw to

secure the ground wire

to the front of the product

as shown. Secure the

other end of the wire to

the main facility ground

connection.

5. MECHANICAL ADJUSTMENTS

Designed to suit exercisers of different heights, the E850 elliptical trainer has an

adjustable stride length. To modify the stride length, pull the adjustment handle

toward yourself. Then lift the handle up or down to the desired position. Make sure

that the pin on the other side of the handle snaps into place, extending outward from

the hole in the vertical arm.

6. UNDERSTAND THE E850 DISPLAY

DISPLAY Overview

The E850 elliptical trainer is designed for user convenience. With better

feedback about your workout, you get better results. The following explains

the display key and window functions. Please read this manual, understand

the display functions, and thereby get optimum enjoyment and benefit from

this product.

Weight

loss target

heart rate

Actual

heart rate

Cardio

target

heart rate

Workout

program

keys

Resistance

level keys

Workout

illustration

window

Pulse

indicator

Workout

feedback

window

Feedback

row

control

DISPLAY Windows

● The 65% target heart rate window shows the optimum heart rate zone

for weight loss.

● The heart rate window shows actual heart rate.

● The 80% target heart rate window shows the optimim heart rate zone for

cardio conditioning.

● The workout illustration window shows workout illustrations and workout

prompts.

● The exercise feedback window shows workout prompts and information.

● LED indicators light to indicate active programs, scan mode, selection

conrmations, and heart rate.

DISPLAY Keys

CHANGE – Press the CHANGE key while exercising to view different workout

feedback. Active feedback indicators light up. Top row: WORKOUT LEVEL,

CALORIES, TIME, WATTS. Bottom row: DISTANCE, CAL/HR, STRIDES/MIN,

TOTAL STRIDES. In SCAN mode, a different row of feedback is displayed every

six seconds, and the scan indicator ashes every second. If not in scan mode, the

SCAN indicator will remain lit.

QUICK START – Press this key to start exercising without rst entering user infor-

mation such as age and weight. In QUICK START mode, time counts upward; time

values accumulate.

START – Press this key to start exercising after inputting user information.

WORKOUT PROGRAMS – When these indicators ash, or during a workout,

simply press any one of these keys to activate the corresponding workout program.

The workout’s associated LED will light to indicate its activation.

ENTER – After making a selection, press this key to conrm your choice.

▲/▼ -- Press ▲/▼ keys to set USER, AGE, WEIGHT, TIME and LEVEL

values.

STOP/HOLD TO RESET – This key has two functions--pause and reset--the

activation of which depends, in part, on how you began exercising. If you pressed

the QUICK START key to start your workout, press the STOP key to exit the current

workout. If you pressed the START key and began a workout, press the STOP

key to return to the “SELECT PROGRAM” prompt. Workout program indicators will

ash, prompting you to select a workout program. Under any circumstance, holding

the STOP key down for three seconds will allow you to leave the workout and return

to the startup banner screen.

DISPLAY Specications

WORKOUT LEVEL (resistance): 1 to 20

TIME: 00:00 to 99:59 (accumulated workout time or time remaining)

DISTANCE: 0.01-9999 km or mile

CALORIES: 0 to 9999 kcal (expenditure)

CAL/Hr: 0.0 - 999.9 kcal

STRIDES/MIN : 0 to 160 strides per minute

WATTS: 0 to 9999

TOTAL STRIDES : 0 to 9999

7. OPERATE THE E850 ELLIPTICAL TRAINER

There are three ways to activate the E850 elliptical trainer. (1) Press the QUICK

START key to start exercising without rst inputting user information such as age

and weight. (2) Press the START key to start exercising after inputting user infor-

mation such as age and weight. (3) Or simply start exercising at twenty or more

strides per minute. When activated, the display will light up, and the startup banner

screen “SPORTSART-E850” will appear.

QUICK START and START modes of operation are explained below.

OPERATION QUICK START Mode

Press the QUICK START key if you want to begin exercising immediately,

without first entering age and weight values.

QUICK START mode has the following characteristics:

In QUICK START mode, calorie and target heart rate values are calculated

based on the assumption that the exerciser is 35 years old and weighs 75 kg,

165 lb. Time counts upward. The resistance setting begins at level one and

can be changed at any time.

Workout programs, including ZONE TRAINER, can be activated at any

time. In workout programs activated via the QUICK START key, time counts

upward, and the resistance setting can be changed at any time.

If no one exercises on the product, the message “STEP TO START” will

scroll across the display every four seconds. If no one exercises on the

product for 15 seconds, a power saving mode will be activated. All lights

on the display will extinguish except for four flashing lines in the exercise

feedback window. If someone exercises at 20 strides per minute or faster,

lights on the display will appear again. If not, after two minutes, lights on the

display will extinguish.

OPERATION START Mode

Press the START key to take advantage of stored user information. User

age and weight values are used to calculate target heart rates and calorie

expenditures respectively. This provides more accurate target heart rate

and calorie expenditure values. And having user information saved in the

product’s memory allows you to view workout records. Each time that you

exercise your workout time, distance, and calorie expenditure values can

be automatically committed to the product’s memory. You can view this

information when you activate your user ID.

To establish a user ID, follow the instructions below.

1. At the startup banner screen (when “SPORTSART-E850” appears),

press the START key. The message window will show the previous user’s

ID and accumulated workout data. Every six seconds, one of the following

messages will appear:

USER - 1

TIME - 25:05

DIST - 15.8

CALS - 1020

Note: The values that appear on the product will probably differ from those

shown above.

Press ▲/▼ keys to select one of four user IDs (1, 2, 3, or 4). Then press the

ENTER key to confirm your choice.

2. Rather than having a user ID number, you can create your own user name

with up to 11 alphabetical characters. To do so, follow the instructions below.

(You can skip this step if desired.) While the user ID number appears, press

and hold the CHANGE key for three seconds. This activates the user name

setting mode. “ENTER NAME” will appear on the product display.

E N T E R N A M E

Press ▲/▼ keys to select alphabetical characters. When your preference

appears, press the ENTER key to confirm your choice. Use this method to

select up to 11 characters. When your user ID name has been completed,

hold the ENTER key for three seconds. The display will show the “USER ID”

prompt.

OPERATION START Mode (Continued)

To modify or delete a user ID name, complete the following procedure. As

the user name appears, hold the CHANGE key for three seconds. The user

name will disappear. Then create a new user name as explained above.

To delete user data (accumulated workout time, strides, and distance), while

the user ID appears, simultaneously press the STOP and START keys.

3. Follow instructions below to input user age and weight information. The

“AGE” prompt will appear on the display. The age setting range is 10 to

99 years with a default age of 35 years. Press ▲/▼ keys to select an age

value. The age value is used to calculate heart rate target values. Press the

ENTER key to confirm the age setting and proceed to the weight setting.

The “WEIGHT” prompt will appear on the display. The weight range is 30

to 180 kg, 66 to 400 lb., with a default value of 75 kg, 165 lb. Press ▲/▼

keys to select a weight value. The weight value is used to calculate calorie

expenditure. Press the ENTER key to confirm the weight setting and proceed

to the program setting.

4. Follow instructions below to select a workout program. Press the workout

program key of your choice. The workout program indicator LED will become

lit. Press the ENTER key to confirm your choice and procedd to the time

setting.

Note: The ZONE TRAINER program can only be activated via another

workout and after a heart rate value has been obtained.

5. Follow instructions below to establish the duration of your workout. Press

▲/▼ keys to select a time value. Then press the ENTER key to confirm the

time settting and begin the workout.

Workout programs have the following characteristics in common:

● When a workout is selected, its corresponding illustration appears on the

display. In the workout illustration, the ashing LED represents the exer-

ciser’s current position in the workout.

● If a different program is selected while time is counting upward, the time

value will continue to accrue from the new segment.

● If a different program is selected while time is counting down in a user

ID-activated program, values accumulate from that segment.

● Note that ZONE TRAINER differs from other programs. Refer to Pro-

grams below for information about that particular workout.

La page charge ...

SportsArt E850 Le manuel du propriétaire

Marque: SportsArt

Modèle: E850

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: SportsArt E850 Owner's manual

SportsArt E850 Le manuel du propriétaire

SportsArt E850 Le manuel du propriétaire

dans d''autres langues

Documents connexes