ESAB Genuine Heliarc HW-90 & HW-90 Pencil Tig Welding Torches Troubleshooting instruction
- Catégorie
- Système de soudage
- Taper
- Troubleshooting instruction
RATING: With standard or gas lens collet bodies: 110
amps. (ACHF or DCSP) Continuous duty 120 amps.
at 50% duty cycle. (Using standard collet bodies.)
COOLING: Air-cooled design.
ELECTRODES: Uses .020, .040, and 1/16-in. diam-
eter electrodes, 3-in. or 7-in. long. Both the short torch
cap (designed for 3-in, electrodes) and the long cap
are supplied with the HW-90 torch. See Table 1 for
electrode diameter vs. current recommendations.
COLLETS: Available for each electrode size. See
Table 2. One collet body (supplied with torch) is used
with each collet.
CUPS: For use with standard collet bodies: Standard,
high impact, and long high-impact in ceramic sizes 4.
5, and 6. See Table 3.
For use with gas lens collet bodies: High-impact ce-
ramic in sizes 4, 5, 6, and 7. See Table 3.
TORCH DIMENSIONS: HW-90
Length, approx ................................. 8-3/4-in. (222 mm)
Handle diameter .................................. 3/4-in. 19 mm)
Height of torch head w/short cap .... 3-1/8-in. 79 mm)
w/long cap ...................................... 7-1/8-in. (181 mm)
Diameter of Head ........................... 19/32-in. ( 15 mm)
Head Angle .................................................... 60° or 120°
Weight (less cable)................................ 3 oz. ( 85 g)
HW-90 Pencil
Length, approx ................................. 7-1/8-in. (181 mm)
Handle diameter .................................. 3/4-in. ( 19 mm)
Head Angle .................................................... 180°
Weight (less cable)............................ 5 oz. (142 g)
REQUIRED ACCESSORIES OR SERVICES:
• Collet, collet body, electrode, cup.
• Shielding gas regulator-flowmeter (if cylinder gas
is used) OR flowmeter (if gas is piped).
• Gas Hose, 12-1/2-ft. long (40V77) or 25-ft. long
(34V38) connects between regulator-flowmeter
and torch cable and hose assembly.
• Welding power and shielding gas supplies.
• Power Cable Adaptor (53N43) for connecting torch
power cable to power and gas supplies.
INSTRUCTIONS for
F-9181-U
Dec., 2004
HW-90 & HW-90 PENCIL
TIG WELDING TORCHES
HW-90 Torch, 60/120-deg. head with 12-1 ‘ 2-ft cable .................... . Part No 16X28
HW-90 Torch, 60/120-deg. head with 25-ft cable .............................. Part No 16X44
HW-90 Pencil Torch, 180-deg. head, 12-1/2-ft cable ........................ Part No 16X47
These INSTRUCTIONS are for experienced operators. If you are not fully familiar with the principles of operation and
safe practices for arc equipment, we urge you to read our booklet, Precautions and Safe Practices for Arc Welding,
Cutting and Gouging, Form 52-529. Do not permit untrained persons to install, operate, or maintain this equipment. Do
not attempt to install or operate this equipment until you have read and fully understand these Instructions. If you do
not fully understand these instructions, contact your supplier for further information. Be sure to read the Safety Pre-
cautions on pages 3 and 4 before installing or operating this equipment.
Be sure this information reaches the operator.
You can get extra copies through your supplier.
2
USER RESPONSIBILITY
This equipment will perform in conformity with the description thereof contained in this manual and accompany-
ing labels and/or inserts when installed, operated, maintained, and repaired in accordance with the instructions pro-
vided. This equipment must be checked periodically. Malfunctioning or poorly maintained equipment should not be
used. Parts that are broken, missing, worn, distorted, or contaminated should be replaced immediately. Should such
repair or replacement become necessary, the manufacturer recommends that a telephone or written request for
service advice be made to the Authorized Distributor from whom purchased.
This equipment or any of its parts should not be altered without the prior written approval of the manufacturer.
The user of this equipment shall have the sole responsibility for any malfunction which results from improper use,
faulty maintenance, damage, improper repair, or alteration by anyone other than the manufacturer or a service facility
designated by the manufacturer.
3
WARNING: These Safety Precautions are for
your protection. They summarize precaution-
ary information from the references listed in
Additional Safety Information section. Before
performing any installation or operating procedures, be
sure to read and follow the safety precautions listed below
as well as all other manuals, material safety data sheets,
labels, etc. Failure to observe Safety Precautions can result
in injury or death.
PROTECT YOURSELF AND OTHERS
--
Some welding, cutting, and gouging
processes are noisy and require ear
protection. The arc, like the sun, emits
ultraviolet (UV) and other radiation and
can injure skin and eyes. Hot metal can cause burns.
Training in the proper use of the processes and equip-
ment is essential to prevent accidents. Therefore:
1. Always wear safety glasses with side shields in any work
area, even if welding helmets, face shields, and goggles
are also required.
2. Use a face shield fitted with the correct filter and cover
plates to protect your eyes, face, neck, and ears from
sparks and rays of the arc when operating or observing
operations. Warn bystanders not to watch the arc and
not to expose themselves to the rays of the electric-arc
or hot metal.
3. Wear flameproof gauntlet type gloves, heavy long-sleeve
shirt, cuffless trousers, high-topped shoes, and a weld-
ing helmet or cap for hair protection, to protect against
arc rays and hot sparks or hot metal. A flameproof apron
may also be desirable as protection against radiated
heat and sparks.
4. Hot sparks or metal can lodge in rolled up sleeves,
trouser cuffs, or pockets. Sleeves and collars should be
kept buttoned, and open pockets eliminated from the
front of clothing
5. Protect other personnel from arc rays and hot sparks
with a suitable non-flammable partition or curtains.
6. Use goggles over safety glasses when chipping slag or
grinding. Chipped slag may be hot and can fly far.
Bystanders should also wear goggles over safety glasses.
FIRES AND EXPLOSIONS -- Heat from
flames and arcs can start fires. Hot slag
or sparks can also cause fires and ex-
plosions. Therefore:
1. Remove all combustible materials well away from the
work area or cover the materials with a protective non-
flammable covering. Combustible materials include wood,
cloth, sawdust, liquid and gas fuels, solvents, paints and
coatings, paper, etc.
2. Hot sparks or hot metal can fall through cracks or
crevices in floors or wall openings and cause a hidden
smoldering fire or fires on the floor below. Make certain
that such openings are protected from hot sparks and
metal.“
3. Do not weld, cut or perform other hot work until the
workpiece has been completely cleaned so that there
are no substances on the workpiece which might pro-
duce flammable or toxic vapors. Do not do hot work on
closed containers. They may explode.
4. Have fire extinguishing equipment handy for instant use,
such as a garden hose, water pail, sand bucket, or
portable fire extinguisher. Be sure you are trained in its
use.
SAFETY PRECAUTIONS
10/98
5. Do not use equipment beyond its ratings. For example,
overloaded welding cable can overheat and create a fire
hazard.
6. After completing operations, inspect the work area to
make certain there are no hot sparks or hot metal which
could cause a later fire. Use fire watchers when neces-
sary.
7. For additional information, refer to NFPA Standard 51B,
"Fire Prevention in Use of Cutting and Welding Pro-
cesses", available from the National Fire Protection Asso-
ciation, Batterymarch Park, Quincy, MA 02269.
ELECTRICAL SHOCK -- Contact with live
electrical parts and ground can cause
severe injury or death. DO NOT use AC
welding current in damp areas, if move-
ment is confined, or if there is danger of
falling.
1. Be sure the power source frame (chassis) is connected
to the ground system of the input power.
2. Connect the workpiece to a good electrical ground.
3. Connect the work cable to the workpiece. A poor or
missing connection can expose you or others to a fatal
shock.
4. Use well-maintained equipment. Replace worn or dam-
aged cables.
5. Keep everything dry, including clothing, work area, cables,
torch/electrode holder, and power source.
6. Make sure that all parts of your body are insulated from
work
and from ground.
7. Do not stand directly on metal or the earth while working
in tight quarters or a damp area; stand on dry boards or
an insulating platform and wear rubber-soled shoes.
8. Put on dry, hole-free gloves before turning on the power.
9. Turn off the power before removing your gloves.
10. Refer to ANSI/ASC Standard Z49.1 (listed on next page)
for specific grounding recommendations. Do not mis-
take the work lead for a ground cable.
ELECTRIC AND MAGNETIC FIELDS —
May be dangerous. Electric current flow-
ing through any conductor causes lo-
calized Electric and Magnetic Fields
(EMF). Welding and cutting current cre-
ates EMF around welding cables and
welding machines. Therefore:
1. Welders having pacemakers should consult their physi-
cian before welding. EMF may interfere with some pace-
makers.
2. Exposure to EMF may have other health effects which are
unknown.
3. Welders should use the following procedures to minimize
exposure to EMF:
A. Route the electrode and work cables together. Secure
them with tape when possible.
B. Never coil the torch or work cable around your body.
C. Do not place your body between the torch and work
cables. Route cables on the same side of your body.
D. Connect the work cable to the workpiece as close as
possible to the area being welded.
E. Keep welding power source and cables as far away
from your body as possible.
4
FUMES AND GASES -- Fumes and
gases, can cause discomfort or harm,
particularly in confined spaces. Do
not breathe fumes and gases. Shield-
ing gases can cause asphyxiation.
Therefore:
1. Always provide adequate ventilation in the work area by
natural or mechanical means. Do not weld, cut, or gouge
on materials such as galvanized steel, stainless steel,
copper, zinc, lead, beryllium, or cadmium unless posi-
tive mechanical ventilation is provided. Do not breathe
fumes from these materials.
2. Do not operate near degreasing and spraying opera-
tions. The heat or arc rays can react with chlorinated
hydrocarbon vapors to form phosgene, a highly toxic
gas, and other irritant gases.
3. If you develop momentary eye, nose, or throat irritation
while operating, this is an indication that ventilation is not
adequate. Stop work and take necessary steps to im-
prove ventilation in the work area. Do not continue to
operate if physical discomfort persists.
4. Refer to ANSI/ASC Standard Z49.1 (see listing below)
for specific ventilation recommendations.
5. WARNING: This product, when used for welding or
cutting, produces fumes or gases which
contain chemicals known to the State of
California to cause birth defects and, in
some cases, cancer. (California Health &
Safety Code
§25249.5 et seq.)
CYLINDER HANDLING -- Cylinders, if
mishandled, can rupture and violently
release gas. Sudden rupture of cylin-
der, valve, or relief device can injure or
kill. Therefore:
1. Use the proper gas for the process and use the proper
pressure reducing regulator designed to operate from
the compressed gas cylinder. Do not use adaptors.
Maintain hoses and fittings in good condition. Follow
manufacturer's operating instructions for mounting regu-
lator to a compressed gas cylinder.
2. Always secure cylinders in an upright position by chain
or strap to suitable hand trucks, undercarriages, benches,
walls, post, or racks. Never secure cylinders to work
tables or fixtures where they may become part of an
electrical circuit.
3. When not in use, keep cylinder valves closed. Have
valve protection cap in place if regulator is not con-
nected. Secure and move cylinders by using suitable
hand trucks. Avoid rough handling of cylinders.
4. Locate cylinders away from heat, sparks, and flames.
Never strike an arc on a cylinder.
5. For additional information, refer to CGA Standard P-1,
"Precautions for Safe Handling of Compressed Gases in
Cylinders", which is available from Compressed Gas
Association, 1235 Jefferson Davis Highway, Arlington,
VA 22202.
EQUIPMENT MAINTENANCE -- Faulty or
improperly maintained equipment can
cause injury or death. Therefore:
1. Always have qualified personnel perform the installa-
tion, troubleshooting, and maintenance work. Do not
perform any electrical work unless you are qualified to
perform such work.
2. Before performing any maintenance work inside a power
source, disconnect the power source from the incoming
electrical power.
3. Maintain cables, grounding wire, connections, power
cord, and power supply in safe working order. Do not
operate any equipment in faulty condition.
4. Do not abuse any equipment or accessories. Keep
equipment away from heat sources such as furnaces,
wet conditions such as water puddles, oil or grease,
corrosive atmospheres and inclement weather.
5. Keep all safety devices and cabinet covers in position
and in good repair.
6. Use equipment only for its intended purpose. Do not
modify it in any manner.
ADDITIONAL SAFETY INFORMATION -- For
more information on safe practices for elec-
tric arc welding and cutting equipment, ask
your supplier for a copy of "Precautions and
Safe Practices for Arc Welding, Cutting and
Gouging", Form 52-529.
The following publications, which are available from the
American Welding Society, 550 N.W. LeJuene Road, Mi-
ami, FL 33126, are recommended to you:
1. ANSI/ASC Z49.1 - "Safety in Welding and Cutting"
2. AWS C5.1 - "Recommended Practices for Plasma Arc
Welding"
3. AWS C5.2 - "Recommended Practices for Plasma Arc
Cutting"
4. AWS C5.3 - "Recommended Practices for Air Carbon
Arc Gouging and Cutting"
5. AWS C5.5 - "Recommended Practices for Gas Tung-
sten Arc Welding“
6. AWS C5.6 - "Recommended Practices for Gas Metal Arc
Welding"“
7. AWS SP - "Safe Practices" - Reprint, Welding Hand-
book.
8. ANSI/AWS F4.1, "Recommended Safe Practices for
Welding and Cutting of Containers That Have Held
Hazardous Substances."
MEANING OF SYMBOLS - As used through-
out this manual: Means Attention! Be Alert!
Your safety is involved.
Means immediate hazards which, if
not avoided, will result in immediate,
serious personal injury or loss of life.
Means potential hazards which could
result in personal injury or loss of life.
Means hazards which could result in
minor personal injury.
SP98-10
5
tibles du secteur où l’on exécute des soudures ou des
coupes à l’arc, à moins de les recouvrir complètement
d’une bâche non-inflammable. Ce type de matériaux
comprend notamment le bois, les vêtements, la sciure,
l’essence, le kérosène, les peintures, les solvants, le
gaz naturel, l’acétylène, le propane et autres sub-
stances combustibles semblables.
b. Les étincelles ou les projections de métal incandes-
cent peuvent tomber dans des fissures du plancher ou
dans des ouvertures des murs et y déclencher une
ignition lente cachée. Veiller à protéger ces ouvertures
des étincelles et des projections de métal.
c. N’exécutez pas de soudures, de coupes, d’opérations
de gougeage ou autres travaux à chaud à la surface
de barils, bidons, réservoirs ou autres contenants
usagés, avant de les avoir nettoyés de toute trace de
substance susceptible de produire des vapeurs
inflammables ou toxiques.
d. En vue d’assurer la prévention des incendies, il
convient de disposer d’un matériel d’extinction prêt à
servir immédiatement, tel qu’un tuyau d’arrosage, un
seau à eau, un seau de sable ou un extincteur portatif.
e. Une fois le travail à l’arc terminé, inspectez le secteur
de façon à vous assurer qu’aucune étincelle ou projec-
tion de métal incandescent ne risque de provoquer
ultérieurement un feu.
3. CHOC ÉLECTRIQUE-- Le gougeage à l’arc et à l’arc
au plasma exige l’emploi de tensions à vide relativement
importantes; or, celles-ci risquent de causer des
dommages corporels graves et même mortels en cas
d’utilisation inadéquate. La gravité du choc électrique
reçu dépend du chemin suivi par le courant à travers le
corps humain et de son intensité.
a. Ne laissez jamais de surfaces métalliques sous ten-
sion venir au contact direct de la peau ou de vêtements
humides. Veillez à porter des gants bien secs.
b. Si vous devez effectuer un travail sur une surface
métallique ou dans un secteur humide, veillez à assu-
rer votre isolation corporelle en portant des gants secs
et des chaussures à semelles de caoutchouc et en
vous tenant sur une planche ou une plate-forme
sèche.
c. Mettez toujours à la terre le poste de soudage/coupage
en le reliant par un câble à une bonne prise de terre.
d. N’utilisez jamais de câbles usés ou endommagés. Ne
surchargez jamais le câble. Utilisez toujours un
équipement correctement entretenu.
e. Mettez l’équipement hors tension lorsqu’il n’est pas en
service. une mise à la masse accidentelle peut en effet
provoquer une surchauffe de l’équipement et un dan-
ger d’incendie. Ne pas enrouler ou passer le câble
autour d’une partie quelconque du corps.
f. Vérifiez si le câble de masse est bien relié à la pièce en
un point aussi proche que possible de la zone de
travail. Le branchement des câbles de masse à
l’ossature du bâtiment ou en un point éloigné de la
zone de travail augmente en effet le risque de pas-
sage d’un courant de sortie par des chaînes de
PRÉCAUTIONS DE SÉCURITÉ
AVERTISSEMENT: Ces règles de sécurité ont pour objet
d’ assurer votre protection. Veillez à lire et à observer les
précautions énoncées ci-dessous avant de monter l’
équipement ou de commercer à l’utiliser. Tout défaut
d’observation de ces précautions risque d’entraîner des
blessures graves ou mortelles.
1. PROTECTION INDIVIDUELLE-- Les brûlures de la
peau et des yeux dues au rayonnement de l’arc
électrique ou du métal incandescent, lors du soudage
au plasma ou à l’électrode ou lors du gougeage à
l’arc, peuvent s’avérer plus graves que celles résultant
d’une exposition prolongée au soleil. Aussi convient-il
d’observer les précautions suivantes:
a. Portez un écran facial adéquat muni des plaques
protectrices et des verres filtrants appropriés afin de
vous protéger les yeux, le visage, le cou et les oreilles
des étincelles et du rayonnement de l’arc électrique
lorsque vous effectuez des soudures ou des coupes
ou lorsque vous en observez l’exécution.
AVERTISSEZ les personnes se trouvant à proximité
de façon à ce qu’elles ne regardent pas l’arc et à ce
qu’elles ne s’exposent pas à son rayonnement, ni à
celui du métal incandescent.
b. Portez des gants ignifugés à crispins, une tunique
épaisse à manches longues, des pantalons sans
rebord, des chaussures à embout d’acier et un casque
de soudage ou une calotte de protection, afin d’éviter
d’exposer la peau au rayonnement de l’arc électrique
ou du métal incandescent. ll est également souhaitable
d’utiliser un tablier ininflammable de façon à se
protéger des étincelles et du rayonnement thermique.
c. Les étincelles ou les projections de métal incandes-
cent risquent de se loger dans des manches
retroussées, des bords relevés de pantalons ou dans
des poches. Aussi convient-il de garder boutonnés le
col et les manches et de porter des vêtements sans
poches à l’avant.
d. Protégez des étincelles et du rayonnement de l’arc
électrique les autres personnes travaillant à proximité
à l’aide d’un écran ininflammable adéquat.
e. Ne jamais omettre de porter des lunettes de sécurité
lorsque vous vous trouvez dans un secteur où l’on
effectue des opérations de soudage ou de coupage à
l’arc. Utilisez des lunettes de sécurité à écrans ou
verres latéraux pour piquer ou meûler le laitier. Les
piquetures incandescentes de laitier peuvent être
projetées à des distances considérables. Les
personnes se trouvant à proximité doivent également
porter des lunettes de protection.
f. Le gougeage à l’arc et le soudage à l’arc au plasma
produisent un niveau de bruit extrêmement élevé (de
100 à 114 dB) et exigent par conséquent l’emploi de
dispositifs appropriés de protection auditive.
2. PRÉVENTION DES INCENDES-- Les projections de
laitier incandescent ou d’étincelles peuvent provoquer
de graves incendies au contact de matériaux com-
bustibles solides, liquides ou gazeux. Aussi faut-il
observer les précautions suivantes:
a. Éloigner suffisamment tous les matériaux combus-
9/97
6
levage, des câbles de grue ou divers chemins
électriques.
g. Empêchez l’apparition de toute humidité, notamment
sur vos vêtements, à la surface de l’emplacement de
travail, des câbles, du porte-électrode et du poste de
soudage/coupage. Réparez immédiatement toute fuite
d’eau.
4. VENTILATION-- La respiration prolongée des fumées
résultant des opérations de soudage/coupage, à
l’intérieur, d’un local clos, peut provoquer des mal-
aises et des dommages corporels. Aussi convient-il
d’observer les précautions suivantes:
a. Assurez en permanence une aération adéquate de
l’emplacement de travail en maintenant une ventila-
tion naturelle ou à l’aide de moyens mécaniques.
N’effectuez jamais de travaux de soudage ou de
coupage sur des matériaux de zinc, de plomb, de
beryllium ou de cadmium en l’absence de moyens
mécaniques de ventilation capables d’empêcher
l’inhalation des fumées dégagées par ces matériaux.
b. N’effectuez jamais de travaux de soudage ou de
coupage à proximité de vapeurs d’hydrocarbure chloré
résultant d’opérations voisines de dégraissage ou de
pulvérisation. La chaleur dégagée ou le rayonnement
de l’arc peut déclencher la formation de phosgène --
gaz particulièrement toxique -- et d’autres gaz irri-
tants, à partir des vapeurs de solvant.
c. Une irritation momentanée des yeux, du nez ou de la
gorge constatée au cours de l’utilisation de
l’équipement dénote un défaut de ventilation. Arrêtez-
vous de travailler afin de prendre les mesures néces-
saires à l’amélioration de la ventilation. Ne poursuivez
pas l’opération entreprise si le malaise persiste.
d. Certaines commandes comportent des canalisations
où circule de l’hydrogène. L’armoire de commande est
munie d’un ventilateur destiné à empêcher la forma-
tion de poches d’hydrogène, lesquelles présentent un
danger d’explosion; ce ventilateur ne fonctionne que
si l’interrupteur correspondant du panneau avant se
trouve placé en position ON (Marche). Veillez à
manœuvrer cette commande en vérifiant si le couvercle
est bien en place, de façon à assurer l’efficacité de la
ventilation ainsi réalisée. Ne jamais débrancher le
ventilateur.
e. Les fumées produites par l’opération de soudage ou
de coupage peuvent s’avérer toxiques. Aussi est-il
nécessaire de disposer en permanence d’un dispositif
adéquat de ventilation de type aspirant, afin d’élimi-
ner du voisinage de l’opérateur tout dégagement de
fumée visible.
f. Consultez les recommandations particulières en matière
de ventilation indiquées à l’alinéa 6 de la norme Z49.1
de l’AWS.
5. ENTRETIEN DE L’ÉQUIPEMENT-- Un équipement
entretenu de façon défectueuse ou inadéquate risque
non seulement de réaliser un travail de mauvaise
qualité mais, chose plus grave encore, d’entraîner des
dommages corporels graves, voire mortels en
déclenchant des incendies ou des chocs électriques.
Observez par conséquent les précautions suivantes:
a. Efforcez-vous de toujours confier à un personnel qua-
lifié l’installation, le dépannage et l’entretien du poste
de soudage et de coupage. N’effectuez aucune
réparation électrique sur l’équipement à moins d’être
qua-lifié à cet effet.
b. Ne procédez jamais à une tâche d’entretien quelconque
à l’intérieur du poste de soudage/coupage, avant
d’avoir débranché l’alimentation électrique.
c. Maintenez en bon état de fonctionnement les câbles,
le câble de masse, les branchements, le cordon
d’alimentation et le poste de soudage/coupage.
N’utilisez jamais le poste ou l’équipement s’il présente
une défectuosité quelconque.
d. Prenez soin du poste de soudage et de coupage et des
équipements accessoires. Gardez-les à l’écart des
sources de charleur, notamment des fours, de
l’humidité, des flaques d’eau maintenez-les à l’abri des
traces d’huile ou de graisse, des atmosphères corro-
sives et des intempéries.
e. Laissez en place tous les dispositifs de sécurité et tous
les panneaux de l’armoire de commande en veillant à
les garder en bon état.
f. Utilisez le poste de soudage/coupage conformément à
son usage prévu et n’effectuez aucune modification.
6. INFORMATIONS COMPLÉMENTAIRES RELATIVES
À LA SÉCURITÉ--
Pour obtenir des informations complémentaires sur les
règles de sécurité à observer pour le montage et
l’utilisation d’équipements de soudage et de coupage
électriques et sur les méthodes de travail
recommandées, demandez un exemplaire du livret N°
52529 “Precautions and Safe Practices for Arc Weld-
ing, Cutting and Gouging” publié par ESAB. Nous
conseillons également de consulter les publications
sui-vantes, tenues à votre disposition par l’American
Welding Society, 550 N.W. LeJuene Road, Miami, FL
32126:
a. “Safety in Welding and Cutting” AWS Z49.1
b. “Recommended Safe Practices for Gas-Shielded Arc
Welding “AWS A6. 1.
c. “Safe Practices for Welding and Cutting Containers
That Have Held Combustibles” AWS-A6.0.
d. “Recommended Safe Practices for Plasma Arc Cutting”
AWS-A6. 3.
e. “Recommended Safe Practices for Plasma Arc Weld-
ing” AWS-C5. 1.
f. “Recommended Safe Practices for Air Carbon Arc
Gouging and Cutting” AWS-C5. 3.
g. “Code For Safety in Welding and Cutting” CSA-Standard
W117. 2.
9/97
7
OPTIONAL ACCESSORIES:
• Gas Lens Collet Bodies (see Table 2) for extend-
ing the shielding gas stream so that an electrode
can be extended 3/4-in. beyond the cup. Improves
performance in drafty locations and enables op-
erator to weld inside corners and other hard to
reach places. To use the gas lens, a collet body
insulator (53N85), adaptor (45V52) and special gas
cups (see Table 3) are also required.
• Wrench (59K07) for use with the above gas lens
collet bodies.
• Braided Nylon Sheath, 9-ft. (2075198) and 20-ft.
(2075200) for protecting service lines.
• Tig Accessory Kit (999124) includes long torch cap,
1 each 0.040" and 1/16" collets, collet body, 1 each
No. 4, 5, and high impact cups, and 1 each 7" long
x 0.040" and 1/16" dia. 2% thoriated electrodes.
• Torch Cable Adaptor (19636) connects to torch
body permitting to use HW-17’s high performance
cable P/N 997022 (12-1/2-ft.) or 997023 (25-ft.) with
the HW-90 torch. The cable is designed for low
temperature flexibility and greater heat resistance.
(Do not use adaptor and HW-17 cable with the
pencil torch.)
SET-UP AND INSTALLATION
1. Connect the regulator/flowmeter to a gas cylinder.
Refer to the instructions supplied with the regula-
tor/flowmeter for details on attaching and adjust-
ing the regulator.
2. Connect one end of the gas hose (40V77 or 34V38)
to the regulator outlet; and the other end to the
torch cable adaptor (53N43).
3. Connect the power cable adaptor to the welding
power source, either directly or through a suitable
length of welding cable fitted with lugs.
4. If using the standard torch accessories, refer to
Fig. 1 and install collet, electrode, and cup as fol-
lows:
a. Remove the insulator sleeve and collet body
from the torch.
b. Place the correct size electrode and collet into
the top end of the collet body, making sure the
bottom end of the collet mates with the tapered
seat in the collet body.
c. Screw the collet body into the front end of the
torch body.
d. Install the insulator sleeve so that it fits between
the groove on the collet body and the flange
on the torch body. A clockwise rotation of the
sleeve will then tighten the collet on the elec-
trode.
e. Screw the proper size ceramic cup onto the
collet body.
f. Adjust the electrode so that it extends 1/8-in.
to 3/16-in. beyond the end of the cup. This is
done by turning the collet insulator sleeve about
one-quarter turn to the left, adjusting the elec-
trode, and tightening the collet insulator sleeve
again with the fingers.
5. If using the optional gas lens accessories, install
the parts as follows:
a. Remove the sleeve and the standard collet
body from the torch (the standard collet body
is not required for this installation).
b. Referring to the inset of Fig. 1, install the sleeve
onto the adaptor (45V52); place the insulator
(53N85) over the small diameter end of the
gas lens collet body; and then screw the collet
body into the adaptor. Tighten with a wrench
(special collet body wrench (59K07) is avail-
able).
c. Insert the selected electrode and collet (tapered
end first) into the adaptor end.
d. Screw the entire assembly (adaptor end first)
into the front end of the torch. Rotating the
sleeve clockwise will tighten the collet on the
electrode.
e. Install the selected gas lens cup onto the collet
body.
f. Electrode may be adjusted to extend from
1/8-in. to 3/4-in. beyond the cup depending
on the nature of the work. Turn the sleeve
about 1/4 turn or less to loosen the electrode.
OPERATING INSTRUCTIONS
1. Make sure that all gas connections in the system
have been securely tightened, and that the torch
cap (on the HW-90 with 600/1200 head) has been
well-tightened.
2. With the regulator flow-adjusting valve closed, open
the gas cylinder or station valve.
Fig. 1 - Exploded View of HW-90 Torch
GAS LENS ACCESSORIES
COLLET
CUP
ADAPTOR - 45V52
BODY
SLEEVE
INSULATOR - 53N85
COLLET BODY
WITH INTEGRAL
GAS LENS
CAP
“O” RING
HANDLE
BODY
COLLET
“O” RING
SLEEVE
COLLET BODY
CUP
8
Table 1 - Electrode Sizes for
Different Welding Currents
Welding Currents, Amperes
Electrode ACHF* DCSP•† DCRP†
Size
(in.) Pure Thoriated Pure or Pure or
Tungsten Tungsten Thoriated Thoriated
0.020 5-15 5-20 5-20 —
0.040 10-60 15-80 15-80 —
1/16 50-100 70-110 70-110 10-20
• In general, for DCSP, the lower end of the specified current range applies to
the pure tungsten electrodes and the upper end of the thoriated tungsten
electrodes.
* Maximum values for unbalanced wave transformers. Balanced wave re-
duces maximum by about 30 per cent.
NOTE: All current values are metered readings. Transformers designed for
metal-arc welding deliver about 15 per cent more than shown on their scale
readings.
† Thoriated tungsten electrodes are recommended when gas lens and high
frequency starting are used.
Table 2 - Collets and Collet Bodies
Size, in. .020 .040 1/16
Collet 84Z34 84Z35 84Z33
Gas Lens Collet Body* 45V41 45V42 45V43
* An adaptor (45V52) and insulator (53N85) are also required when
using a gas lens.
3. Set the power supply for the desired welding cur-
rent.
4. Open all shielding gas valves downstream from the
flowmeter or flowmeter/regulator (e.g.,
lever-operated shutoff valve, or solenoid-operated
valve in power supply).
5. Set shielding gas flow to the desired level, as reg-
istered on flowmeter tube or gauge. NOTE: Purge
the gas hose by allowing the gas to flow long enough
(up to 15 minutes on new torch; less than five min-
utes thereafter). This will help prevent weld con-
tamination.
6. Close control switch at work station or power sup-
ply.
7. Draw a test arc on a heavy piece of scrap steel or
copper. (Do NOT use a carbon block, which will
tend to contaminate the electrode.)
8. If the test arc is satisfactory, commence welding.
OPERATION AND MAINTENANCE HINTS
1. A poor shielding gas connection, or a leaky hose,
will not only waste gas but permit the entry of minute
amounts of air, sufficient to contaminate both the
electrode and the weld. Trouble signs: a bluish cast
on the electrode after it has cooled; in welding alu-
minum, a dark gray deposit on or beside the weld
bead.
2. Keep the torch hose away from hot metal. The plas-
tic hose begins to lose strength at 1250 F. (52° C)..
3. Do not try to repair a damaged power cable. Re-
place it.
4. If an electrode becomes contaminated, shut off
power, then remove electrode from torch. Break
off the contaminated end (nicking with a grinding
wheel first will help) and replace electrode.
5. Keep an eye on the sealing ‘0’ rings on the collet
body and torch cap. If it shows sign of wear or dis-
tortion, cut it off. Then install a new ring (85W49).
Apply a little silicone grease to the new ring before
attempting to slide it over the cap threads.
Table 3 - Cups
Cup No. 4567
Ceramic Cup 84Z36 84Z37 84Z86 -
High-Impact Cup 14N65 14N66 14N67 -
Long High-Impact Cup 14N73 14N74 14N75 -
Gas Lens High-impact Cup 53N58 I 53N59 I- 53N60 I 53N61
Fig. 2 - HW-90 Torch -
(60°/120° Head, 12-1/2-ft. cable) - Part No. 16X28
(60°/120° Head, 25-ft. cable) - Part No. 16X44
O’RING - 85W49
SLEEVE - 105Z26
COLLET
(See Accessory List)
COLLET BODY - 105Z27
CUP
(See Accessory List)
5/8 X 18
CAP ASSEMBLY - 84Z31 (Short)
(Includes) “O” RING - 85W49
TORCH BODY - 56Y35
3/8 X 24
TORCH HANDLE - 105Z55
3/8 X 24
CABLE & HOSE ASSY.
56Y38 (12 1/2 FT. LONG)
56Y97 (25 FT. LONG)
CABLE ADAPTOR - 53N43 (Accessory)
For Gas Lens Accessories, See Fig. 1.
PARTS SUPPLIED
TORCH CAP - 56Y40 (Long)
(Includes)
“O” RING - 85W49
SLEEVE - 105Z26
Fig. 3 - HW-90 Pencil Torch (12-1/2-ft. cable) - Part No. 16X47
O’RING - 85W49
SLEEVE - 105Z26
COLLET
(See Accessory List)
CUP
(See Accessory List)
5/8 X 18
TORCH HANDLE - 105Z55
3/8 X 24
CABLE & HOSE ASSY.
56Y38 (12 1/2 FT. LONG)
56Y97 (25 FT. LONG)
For Gas Lens Accessories, See Fig. 1.
3/8 X 24
TORCH BODY - 56Y35
CABLE ADAPTOR - 53N43 (Accessory)
BOOT - 86Z25
9
TORCH BODY - 56Y35
3/8 X 24 M
POWER CABLE - 3/8 X 24 F
3/8 X 24 F
5/8 X 18 F
3/8 X 24 F
5/8 X 18 F
3/8 X 24 F
TORCH BODY - 86Z24
COLLET BODY - 105Z27
10
11
Genuine Heliarc
®
is a registered trademark of ESAB Welding & Cutting Products.
F-9181-U 12 / 2004 Printed in U.S.A.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
ESAB Genuine Heliarc HW-90 & HW-90 Pencil Tig Welding Torches Troubleshooting instruction
- Catégorie
- Système de soudage
- Taper
- Troubleshooting instruction
dans d''autres langues
Documents connexes
-
ESAB & HW-9F Tig Welding Torches Manuel utilisateur
-
-
-
-
-
-
-
-
-