Tripp Lite Owner's Manual - HDMI over Cat5 Extenders and Extender/Splitters Le manuel du propriétaire

1

Owner’s Manual

HDMI over Cat5 Extenders

and Extender/Splitters

Extender Kit Models: B126-1A1 and B126-1A1-WP

Local Unit Models: B126-002 and B126-004

Remote Unit Models: B126-1P0, B126-1P0-MINI,

B126-1P0-WP-1, B126-1A0, B126-1A0-WP-1 and B126-110

Español 29 • Français 57

PROTECT YOUR INVESTMENT!

Register your product for quicker service and ultimate peace of mind.

You could also win an ISOBAR6ULTRA surge protector—a $100 value!

www.tripplite.com/warranty

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

17-07-081-933731.indb 1 8/2/2017 8:57:20 AM

2

Package Contents

Product Features

B126-1A1

B126-1A1-WP

B126-002

B126-004

B126-1A0

B126-1A0-WP-1

B126-1P0

B126-1P0-MINI

B126-1P0-WP-1

B126-110

Local Unit (L), Remote Unit (R)

or Both (B)

B B L L R R R R R R

External Power Supplies

(0, 1 or 2)

2 2 1 1 1 1 0 0 0 1

Mounting Hardware X X X X X

Wall Plate Screws X X X

Screwdriver for

Equalization Adjustment

X X X X X

HDMI Daisy-Chain Cable X

USB Micro-B Cable X

All

• Support a maximum video resolution of 1080p (60 Hz)

• Plug and play—no software or drivers required

• Support up to 7.1-channel surround sound audio

• HDCP and 3D compatible

17-07-081-933731.indb 2 8/2/2017 8:57:20 AM

3

Product Features

B126-1A1

• HDMI over Cat5 Active Extender Kit

• Extends a 1080i (60 Hz) signal up to 200 ft. from the source, or a

1080p (60 Hz) signal up to 150 ft. from the source

• Additional HDMI port on the local transmitter unit allows connection of

local monitor

• Remote receiver unit features a built-in equalization control for video

image adjustment

• Includes mounting hardware that allows both the local transmitter

and remote receiver units to be wall-mounted, rack-mounted or

pole-mounted

B126-1A1-WP

• HDMI over Cat5 Active Extender Wall Plate Kit

• Extends a 1080i (60 Hz) signal up to 200 ft. from the source, or a

1080p (60 Hz) signal up to 150 ft. from the source

• Remote receiver unit features a built-in equalization control for video

image adjustment

• RJ45-style wall plates allow for the use of standard Cat5e/6 patch cables;

110 punchdown connection not required

B126-002

• 2-Port HDMI over Cat5 Extender/Splitter Local Transmitter Unit

• Splits an HDMI signal into two

• Works with remote/repeater and receiver units to extend an HDMI signal

past the 16 ft. (5 m) distance limitation

• Includes mounting hardware that allows unit to be wall-mounted,

rack-mounted or pole-mounted

17-07-081-933731.indb 3 8/2/2017 8:57:20 AM

4

Product Features

B126-004

• 4-Port HDMI over Cat5 Extender/Splitter Local Transmitter Unit

• Splits an HDMI signal into four

• Includes an additional HDMI port, which can be used to connect a local

monitor or to daisy-chain additional B126-004 units (up to three units

can be daisy-chained together)

•

Includes HDMI cable with latching connectors for a more secure connection

• Works with remote/repeater and receiver units to extend an HDMI signal

past the 16 ft. (5 m) distance limitation

• Includes mounting hardware that allows unit to be wall-mounted,

rack-mounted or pole-mounted

• Up to three B126-004 units can be mounted in a B132-004-RB

1U rack-mount bracket

B126-1A0

• HDMI over Cat5 Active Extender Remote Receiver Unit

• Works with B126-002 and B126-004 extender/splitters to extend a

1080i (60 Hz) signal up to 200 ft. from the source, or a 1080p (60 Hz)

signal up to 150 ft. from the source

• Built-in equalization control for video image adjustment

• Includes mounting hardware that allows the unit to be wall-mounted,

rack-mounted or pole-mounted

B126-1A0-WP-1

• HDMI over Cat5 Active Extender Wall Plate

• Works with B126-002 and B126-004 extender/splitters to extend a

1080i (60 Hz) signal up to 200 ft. from the source, or a 1080p (60 Hz)

signal up to 150 ft. from the source

• Built-in equalization control for video image adjustment

• RJ45-style wall plate allows for the use of standard Cat5e/6 patch cables;

110 punchdown connection not required

17-07-081-933731.indb 4 8/2/2017 8:57:20 AM

5

Product Features

B126-1P0

• HDMI over Cat5 Passive Extender Remote Receiver Unit

• Works with B126-002 and B126-004 extender/splitters to extend a

1080i (60 Hz) signal up to 100 ft. from the source, or a 1080p (60 Hz)

signal up to 50 ft. from the source

• Built-in HDMI cable has latching connector for a more secure connection

• No external power required

B126-1P0-MINI

• HDMI over Cat5 Passive Extender Remote Receiver Unit (Compact)

• Works with B126-002 and B126-004 extender/splitters to extend a

1080i (60 Hz) signal up to 100 ft. from the source, or a 1080p (60 Hz)

signal up to 50 ft. from the source

• Low proﬁle and compact design allows for discreet placement

• No external power required; USB Micro-B port provides power if needed

• Includes USB Micro-B cable

B126-1P0-WP-1

• HDMI over Cat5 Passive Extender Wall Plate

• Works with B126-002 and B126-004 extender/splitters to extend a

1080i (60 Hz) signal up to 100 ft. from the source, or a 1080p (60 Hz)

signal up to 50 ft. from the source

• RJ45-style wall plate allows for the use of standard Cat5e/6 patch cables;

110 punchdown connection not required

• No external power required

17-07-081-933731.indb 5 8/2/2017 8:57:20 AM

6

Product Features

B126-110

• HDMI over Cat5 Active Extender Remote/Repeater Unit

• Extends and expands an HDMI over Cat5 installation, allowing multiple

monitors to be located at different points in a chain of up to 700 ft.

• Extends a 1080i (60 Hz) signal up to 175 ft., or a 1080p (60 Hz) signal

up to 125 ft. from the local transmitter unit to the ﬁrst remote/repeater

unit in the installation

• Extends a 1080i (60 Hz) signal up to an additional 175 ft. or a 1080p

(60 Hz) signal up to an additional 125 ft. from each remote/repeater unit

to the next unit in the chain (in a full four-level daisychain installation, a

1080i (60 Hz) signal can be extended up to 700 ft. or a 1080p (60 Hz)

signal up to 500 ft. from the source to the last remote unit in the chain)

• Connect up to four remote units (three remote/repeaters and one

receiver) with a monitor located at each point in the chain

• Built-in equalization control for video image adjustment

• Includes mounting hardware that allows the unit to be wall-mounted,

rack-mounted or pole-mounted

Optional Accessories:

• B132-004-RB 1U Rack-Mount Bracket

• N202-Series Cat6 24 AWG Solid Wire Patch Cables

• P568-Series High-Speed HDMI Cables

17-07-081-933731.indb 6 8/2/2017 8:57:20 AM

7

Mounting Instructions (select models only)

The B126-002, B126-004, B126-1A1, B126-1A0 and B126-110 include

mounting hardware that allows for a variety of mounting methods. The

following images illustrate how the included mounting brackets can be

attached for different installations.

Note: The B126-004 can also be mounted to a Tripp Lite B132-004-RB 1U

Rack-Mount Bracket. Up to three B126-004 local units can be connected to a

B132-004-RB.

Wall Mount

19” Rack Mount Pole Mount

17-07-081-933731.indb 7 8/2/2017 8:57:22 AM

OPTIONAL LOCAL

MONITOR

LOCAL

TRANSMITTER

REMOTE

RECEIVER

Up to 200 ft. at 1080i (60Hz)

Up to 150 ft. at 1080p (60Hz)

BLU-RAY

8

Standard Extender Kit Installation

Notes:

1) Test to ensure the entire installation works properly before pulling cables through

ceilings/walls.

2) To achieve maximum distance and performance, use 24 AWG solid wire Cat5e/6

cable. Using stranded wire Cat5e/6 cable, or cable with a gauge (AWG) size higher

than 24 AWG, will result in shorter extension distance. Higher gauge cabling, such

as 26 AWG, has a more limited transmission capability than lower gauge cabling.

All Tripp Lite N202-Series Cat6 cables are made with 24 AWG solid wire cabling.

3) The B126-1A1 and B126-1A1-WP are set to transmit a stereo audio signal by

default. Press the Audio button on the local unit to switch to 7.1-channel surround-

sound audio.

4) The installation diagram shows a B126-1A1 unit. The B126-1A1-WP installation is

the same, except there is no local monitor port.

17-07-081-933731.indb 8 8/2/2017 8:57:23 AM

9

Standard Extender Kit Installation

1

Make sure the HDMI source is powered OFF.

2

Connect the HDMI source to the INPUT port on the B126-1A1 or

B126-1A1-WP local unit using a Tripp Lite P568-Series HDMI Cable.

3

Optional for B126-1A1: Connect a local monitor to the LOCAL port on

the B126-1A1 local unit using a Tripp Lite P568-Series HDMI Cable.

4

Connect the external power supply to the local unit and plug it

into a Tripp Lite Surge Protector, Power Distribution Unit (PDU) or

Uninterruptible Power Supply (UPS). The green LED illuminates to

indicate the unit is receiving power from the external power supply.

5

Using Cat5e/6 cable, connect the RJ45 port on the local unit to the

RJ45 port on the remote unit.

6

Connect the external power supply to the remote unit and plug it into

a Tripp Lite Surge Protector, PDU or UPS. The green LED illuminates to

indicate the unit is receiving power from the external power supply. The

orange LED illuminates to indicate the unit is connected to a powered

ON local unit.

7

Connect the remote unit’s HDMI port to a monitor using a Tripp Lite

P568-Series HDMI Cable.

8

Turn on the power to the HDMI source. The orange LED on the local unit

illuminates to indicate a signal is being received from the source.

9

If necessary, use the Equalization control on the remote unit to adjust

the video image.

Note: An improper Equalization setting can cause the monitor not to display a

picture at all. Try each Equalization setting until an acceptable picture is displayed.

17-07-081-933731.indb 9 8/2/2017 8:57:23 AM

OPTIONAL LOCAL

MONITOR

B126-1A1 LOCAL

TRANSMITTER

B126-1A1 REMOTE

RECEIVER

B126-110 REMOTE

REPEATER

B126-110 REMOTE

REPEATER

B126-110 REMOTE

REPEATER

Up to 175 ft. at 1080i (60Hz)

Up to 125 ft. at 1080p (60Hz)

Up to 175 ft. at 1080i (60Hz)

Up to 125 ft. at 1080p (60Hz)

BLU-RAY

Up to 175 ft. at 1080i (60Hz)

Up to 125 ft. at 1080p (60Hz)

Up to 175 ft. at 1080i (60Hz)

Up to 125 ft. at 1080p (60Hz)

10

Extender Kit with Remote/Repeater Installation

Notes:

1) Test to ensure the entire installation works properly before pulling cables through

ceilings/walls.

2) To achieve maximum distance and performance, use 24 AWG solid wire Cat5e/6

cable. Using stranded wire Cat5e/6 cable, or cable with a gauge (AWG) size higher

than 24 AWG, will result in shorter extension distance. Higher gauge cabling, such

as 26 AWG, has a more limited transmission capability than lower gauge cabling.

All Tripp Lite N202-Series Cat6 cables are made with 24 AWG solid wire cabling.

3) The B126-1A1 and B126-1A1-WP are set to transmit a stereo audio signal by

default. Press the Audio button on the local unit to switch to 7.1-channel surround-

sound audio.

4) The installation diagram shows a B126-1A1 unit. The B126-1A1-WP installation is

the same, except there is no local monitor port.

1

Make sure the HDMI source is powered OFF.

2

Connect the HDMI source to the INPUT port on the B126-1A1 or

B126-1A1-WP using a Tripp Lite P568-Series HDMI Cable.

3

Optional for B126-1A1: Connect a local monitor to the LOCAL HDMI

port using a Tripp Lite P568-Series HDMI Cable.

17-07-081-933731.indb 10 8/2/2017 8:57:24 AM

11

Extender Kit with Remote/Repeater Installation

4

Connect the external power supply to the local unit and plug it into a

Tripp Lite Surge Protector, PDU or UPS. The green LED illuminates to

indicate the unit is receiving power from the external power supply.

5

Using Cat5e/6 cable, connect the RJ45 port on the local unit to the

RJ45 INPUT port on the B126-110 remote/repeater unit.

6

Connect a monitor to the HDMI OUTPUT port on the remote/repeater

unit using a Tripp Lite P568-Series HDMI Cable.

7

Connect the external power supply to the remote/repeater unit and plug

it into a Tripp Lite Surge Protector, PDU or UPS. The green power LED

and the green RJ45 LEDs illuminate to indicate the unit is receiving

power.

Up to four units can be daisy-chained (three remote/repeaters and one

receiver). To connect additional remote/repeater units, proceed to step 8.

To ﬁnish your installation with the B126-1A1 or B126-1A1-WP remote

receiver unit, proceed to step 12.

8

Using Cat5e/6 cable, connect the RJ45 OUTPUT port on the ﬁrst

remote/repeater unit to the RJ45 INPUT port on a second remote/

repeater unit.

9

Connect a monitor to the HDMI OUTPUT port on the remote/repeater

unit you just added using a Tripp Lite P568-Series HDMI Cable.

10

Connect the external power supply to the remote/repeater unit and plug

it into a Tripp Lite Surge Protector, PDU or UPS. The green power LED

and the green RJ45 LEDs illuminate to indicate the unit is receiving

power.

11

To add a third remote/repeater unit, repeat steps 8 through 10.

To ﬁnish your installation with the B126-1A1 or B126-1A1-WP remote

receiver unit, proceed to step 12.

17-07-081-933731.indb 11 8/2/2017 8:57:24 AM

12

Extender Kit with Remote/Repeater Installation

12

Using Cat5e/6 cable, connect the RJ45 OUTPUT port on the last remote/

repeater unit to the RJ45 INPUT port of the B126-1A1 or B126-1A1-WP

remote receiver unit.

13

Connect a monitor to the HDMI OUTPUT port on the remote receiver unit

using a Tripp Lite P568-Series HDMI Cable.

14

Connect the external power supply to the remote receiver unit and

plug it into a Tripp Lite Surge Protector, PDU or UPS. The green LED

illuminates to indicate the unit is receiving power from the external

power supply. The orange LED illuminates to indicate the unit is

connected to a powered ON remote/repeater unit.

15

Turn on the power to the HDMI source. The orange LED on the local unit

illuminates to indicate a signal is being received from the source.

16

If necessary, use the Equalization control on the remote/repeater unit(s)

and remote receiver unit to adjust the video image.

Note: An improper Equalization setting can cause the monitor not to display a

picture at all. Try each Equalization setting until an acceptable picture is displayed.

17-07-081-933731.indb 12 8/2/2017 8:57:24 AM

B126-004

OPTIONAL LOCAL

MONITOR

BLU-RAY

B126-1P0-WP-1B126-1A0-WP-1

B126-1P0B126-1A0

Up to 100 ft. at 1080i (60Hz)

Up to 50 ft. at 1080p (60Hz)

Up to 200 ft. at 1080i (60Hz)

Up to 150 ft. at 1080p (60Hz)

13

Standard Extender/Splitter Installation

Notes:

1) Test to ensure the entire installation works properly before pulling cables through

ceilings/walls.

2) To achieve maximum distance and performance, use 24 AWG solid wire Cat5e/6

cable. Using stranded wire Cat5e/6 cable, or cable with a gauge (AWG) size higher

than 24 AWG, will result in shorter extension distance. Higher gauge cabling, such

as 26 AWG, has a more limited transmission capability than lower gauge cabling. All

Tripp Lite N202-Series cables are made with 24 AWG solid wire cabling.

3) The B126-002 and B126-004 are set to transmit a stereo audio signal by default.

Press the Audio button on the B126-002 or B126-004 to switch to 7.1-channel

surround-sound audio.

4) The installation diagram shows the B126-004 local transmitter unit. The

B126-002 installation is the same except there are only two remote ports and no

local monitor port.

5) External power is not usually required for the B126-1P0-MINI, but it includes a

USB Micro-B port and cable to provide external power when needed. If you are

not getting an image on the monitor when using the B126-1P0-MINI, connect the

included USB cable between the USB Micro-B port and a power source (such as a

USB charger).

17-07-081-933731.indb 13 8/2/2017 8:57:24 AM

14

Standard Extender/Splitter Installation

1

Make sure the HDMI source is powered OFF.

2

Connect the HDMI source to the INPUT port on the B126-002 or

B126-004 using a Tripp Lite P568-Series HDMI Cable.

3

Optional for B126-004: Connect an HDMI monitor to the LOCAL port

on the B126-004 using a Tripp Lite P568-Series HDMI Cable.

4

Connect the external power supply to the B126-002 or B126-004 local

unit and plug it into a Tripp Lite Surge Protector, PDU or UPS. The green

RJ45 LEDs and the red Power LED on the B126-004, and the green

RJ45 LEDs on the B126-002 will illuminate to indicate power is being

received from the external power supply.

5

Using Cat5e/6 cable, connect one of the RJ45 output ports on the local

unit to the RJ45 input port on a B126-1P0, B126-1P0-MINI,

B126-1A0, B126-1P0-WP-1 or B126-1A0-WP-1 remote unit.

6

Repeat step 5 for each additional remote unit being connected.

7

B126-1A0 and B126-1A0-WP-1 only: Connect the external power

supply to the B126-1A0 or B126-1A0-WP-1, and plug it into a

Tripp Lite Surge Protector, PDU or UPS. The green and orange LEDs

illuminate, with the green LED indicating the unit is receiving power from

the external power supply, and the orange LED indicating the unit is

connected to a powered ON local unit via Cat5e/6 cable.

8

Repeat step 7 for each additional B126-1A0 or B126-1A0-WP-1 in the

installation.

9

Connect the B126-1P0 or B126-1P0-MINI HDMI connector to a

monitor. Or, connect the B126-1P0-WP-1, B126-1A0 or B126-1A0-

WP-1

to a monitor using a Tripp Lite P568-Series HDMI Cable. Both the

green and orange RJ45 LEDs on the B126-1P0 and B126-1P0-MINI,

and the green LED on the B126-1P0-WP-1, illuminate to indicate the

unit is receiving power from the connected monitor.

17-07-081-933731.indb 14 8/2/2017 8:57:24 AM

15

Standard Extender/Splitter Installation

10

Repeat step 9 for each additional monitor being connected.

11

Turn on the power to the HDMI source. The orange RJ45 LEDs illuminate

on the B126-002 and B126-004 to indicate the unit is receiving a

signal from the source. The screen should now be displayed on the

connected monitors.

12

If necessary, use the Equalization control on the B126-1A0 or

B126-1A0-WP-1 to adjust the video image.

Note: An improper Equalization setting can cause the monitor not to display a picture

at all. Try each Equalization setting until an acceptable picture is displayed.

17-07-081-933731.indb 15 8/2/2017 8:57:24 AM

OPTIONAL LOCAL

MONITOR

B126-004 LOCAL

TRANSMITTER

B126-110 REMOTE/

REPEATER

B126-110 REMOTE/

REPEATER

B126-110 REMOTE/

REPEATER

Up to 175 ft. at 1080i (60Hz)

Up to 125 ft. at 1080p (60Hz)

Up to 175 ft. at 1080i (60Hz)

Up to 125 ft. at 1080p (60Hz)

BLU-RAY

B126-110 REMOTE/

REPEATER

B126-110 REMOTE/

REPEATER

B126-110 REMOTE/

REPEATER

B126-110 REMOTE/

REPEATER

B126-110 REMOTE/

REPEATER

B126-110 REMOTE/

REPEATER

B126-1A0-WP-1

REMOTE RECEIVER

B126-1A0-WP-1

REMOTE RECEIVER

B126-1A0-WP-1

REMOTE RECEIVER

B126-1A0-WP-1

REMOTE RECEIVER

B126-110 REMOTE/

REPEATER

B126-110 REMOTE/

REPEATER

B126-110 REMOTE/

REPEATER

16

Extender/Splitter with Remote/Repeater Installation

Notes:

1) Test to ensure the entire installation works properly before pulling cables through

ceilings/walls.

2) To achieve maximum distance and performance, use 24 AWG solid wire Cat5e/6

cable. Using stranded wire Cat5e/6 cable, or cable with a gauge (AWG) size higher

than 24 AWG, will result in shorter extension distance. Higher gauge cabling, such

as 26 AWG, has a more limited transmission capability than lower gauge cabling. All

Tripp Lite N202-Series Cat6 cables are made with 24 AWG solid wire cabling.

3) The B126-002 and B126-004 are set to transmit a stereo audio signal by default.

Press the Audio button on the local unit to switch to 7.1-channel surround-sound

audio.

4) The installation diagram shows the B126-004. The B126-002 installation will be

the same, except there are only two remote ports and there is no local monitor port.

17-07-081-933731.indb 16 8/2/2017 8:57:25 AM

17

Extender/Splitter with Remote/Repeater Installation

1

Make sure the HDMI source is powered OFF.

2

Connect the HDMI source to the INPUT port on the B126-002 or

B126-004 using a Tripp Lite P568-Series HDMI Cable.

3

Optional for B126-004: Connect a local monitor to the LOCAL HDMI

port using a Tripp Lite P568-Series HDMI Cable.

4

Connect the external power supply to the local unit and plug it into a

Tripp Lite Surge Protector, PDU or UPS. The green RJ45 LEDs illuminate

to indicate power is being received from the external power supply. An

additional Red LED on the B126-004 also illuminates to indicate power

is being received.

5

Using Cat5e/6 cable, connect one of the RJ45 output ports on the local

unit to the RJ45 input port on the B126-110 remote/repeater unit.

6

Connect a monitor to the HDMI OUTPUT port on the remote/repeater

unit using a Tripp Lite P568-Series HDMI Cable.

7

Connect the external power supply to the remote/repeater unit and plug

it into a Tripp Lite Surge Protector, PDU or UPS. The green power LED

and the Green RJ45 LEDs illuminate to indicate the unit is receiving

power.

Up to four units can be daisy-chained (three remote/repeaters and one

receiver). To connect additional remote/repeater units, proceed to step 8.

To ﬁnish your installation with a B126-1A0 or B126-1A0-WP-1 remote

receiver unit, proceed to step 12.

8

Using Cat5e/6 cable, connect the RJ45 OUTPUT port on the ﬁrst remote/

repeater unit to the RJ45 INPUT port on a second remote/repeater unit.

9

Connect a monitor to the HDMI OUTPUT port on the remote/repeater

unit that you just added using a Tripp Lite P568-Series HDMI Cable.

17-07-081-933731.indb 17 8/2/2017 8:57:25 AM

18

Extender/Splitter with Remote/Repeater Installation

10

Connect the external power supply to the remote/repeater unit and plug

it into a Tripp Lite Surge Protector, PDU or UPS. The green power LED

and the green RJ45 LEDs illuminate to indicate the unit is receiving

power.

11

To add a third remote/repeater unit, repeat steps 8 through 10.

To ﬁnish your installation with a B126-1A0 or B126-1A0-WP-1 remote

receiver unit, proceed to step 12.

12

Using Cat5e/6 cable, connect the RJ45 OUTPUT port on the last remote/

repeater unit to the RJ45 INPUT port on a B126-1A0 or B126-1A0-WP-1

remote receiver unit.

13

Connect a monitor to the HDMI OUTPUT port on the remote receiver unit

using a Tripp Lite P568-Series HDMI Cable.

14

Connect the external power supply to the remote receiver unit and

plug it into a Tripp Lite Surge Protector, PDU or UPS. The green LED

illuminates to indicate the unit is receiving power from the external

power supply. The orange LED illuminates to indicate the unit is

connected to a powered ON remote/repeater unit.

15

Repeat steps 5 through 14 for each additional RJ45 output port on the

local transmitter unit.

16

Turn on the power to the HDMI source. The orange RJ45 LEDs on the

local unit illuminate to indicate a signal is being received from the

source.

17

If necessary, use the Equalization control on the remote/repeater unit(s)

and remote receiver unit to adjust the video image.

Note: An improper Equalization setting can cause the monitor not to display a

picture at all. Try each Equalization setting until an acceptable picture is displayed.

17-07-081-933731.indb 18 8/2/2017 8:57:25 AM

19

Extender/Splitter Daisy-Chain Installation (B126-004 only)

Notes:

1) Test to ensure the entire installation works properly before pulling cables through

ceilings/walls.

2) To achieve maximum distance and performance, use 24 AWG solid wire Cat5e/6

cable. Using stranded wire Cat5e/6 cable, or cable with a gauge (AWG) size higher

than 24 AWG, will result in shorter extension distance. Higher gauge cabling, such

as 26 AWG, has a more limited transmission capability than lower gauge cabling. All

Tripp Lite N202-Series cables are made with 24 AWG solid wire cabling.

3) The B126-004 is set to transmit a stereo audio signal by default. Press the Audio

button on the B126-004 to switch to 7.1-channel surround-sound audio.

4) Using the B126-1A0 and B126-1A0-WP-1, a 1080i (60 Hz) signal can be extended

up to 200 ft. from the source, or a 1080p (60 Hz) signal up to 150 ft. from the

source. Using a B126-1P0, B126-1P0-MINI or B126-1P0-WP-1, a 1080i (60Hz)

signal can be extended up to 100 ft. from the source, or a 1080p (60Hz) signal up

to 50 ft.

17-07-081-933731.indb 19 8/2/2017 8:57:25 AM

Level 1

Level 2

Level 3

OPTIONAL LOCAL MONITOR

BLU-RAY

20

Extender/Splitter Daisy-Chain Installation (B126-004 only)

17-07-081-933731.indb 20 8/2/2017 8:57:25 AM

La page charge ...

Tripp Lite Owner's Manual - HDMI over Cat5 Extenders and Extender/Splitters Le manuel du propriétaire

Tripp Lite Owner's Manual - HDMI over Cat5 Extenders and Extender/Splitters Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents