Brinkmann Natural Gas Conversion Kit Guide d'installation

Gaz Naturel Ensemble de Conversion

PROFESSIONAL INSTALLATION MANUAL

WARNING

HAZARDOUS EXPLOSION MAY RESULT IF THESE

WARNINGS AND INSTRUCTIONS ARE IGNORED. READ

AND FOLLOW ALL WARNINGS AND INSTRUCTIONS IN

THIS MANUAL TO AVOID PERSONAL INJURY,

INCLUDING DEATH OR PROPERTY DAMAGE.

ASSEMBLY AND OPERATING IN STRUC TIONS

INSTRUCCIONES DE ARMADO Y OPERACIÓN

SAVE THIS MANUAL FOR FUTURE REFERENCE

VEUILLEZ CONSERVER CE MANUEL COMME RÉFÉRENCE

NOTICE TO

PROFESSIONAL INSTALLER:

LEAVE THESE INSTRUCTIONS WITH

THE GRILL OWNER FOR FUTURE

REFERENCE .

CONVERTS MOST CHARMGLOW AND BRINKMANN GRILLS

FROM PROPANE TO NATURAL GAS. CHECK WITH BRINKMANN IF YOUR

MODEL NUMBER IS NOT LISTED. FOR MODEL NUMBERS

810-8502-F, 810-8533-F, AND 810-9521-F

IF YOU DO NOT HAVE THE PROFESSIONAL INSTALLATION MANUAL, PLEASE

VISIT WWW.BRINKMANN.NET OR CALL (800) 527-0717.

AVERTISSEMENT À

L'INTENTION DE

L'INSTALLATEUR

PROFESSIONNEL :

VEUILLEZ LAISSER CES

INSTRUCTIONS AU PROPRIÉTAIRE

DU GRIL POUR CONSULTATION

ULTRIEURE.

Natural Gas Conversion Kit

MANUEL D'INSTALLATION PROFESSIONNELLE

IL EST IMPÉRATIF DE SUIVRE LES INSTRUCTIONS ET DE

RESPECTER LES AVERTISSEMENTS, SANS QUOI DES

EXPLOSIONS DANGEREUSES PEUVENT SURVENIR.

VEUILLEZ LIRE ET RESPECTER TOUS LES AVERTISSEMENTS

ET TOUTES LES INSTRUCTIONS QUE CONTIENT CE MANUEL

AFIN D'ÉVITER LES BLESSURES CORPORELLES, DONT LA

MORT ET LES DOMMAGES MATÉRIELS.

CONVERTIT DU GAZ PROPANE (PÉTROLE LIQUÉFIÉ) AU GAZ NATUREL LES GRILS

CHARMGLOW ET BRINKMANN SUIVANTS. VÉRIFIEZ AVEC LE BRINKMANN SI

VOTRE NUMÉRO DE TYPE N'EST PAS ÉNUMÉRÉ. POUR DES NUMÉROS MODÈLES

810-8502-F, 810-8533-F, Y 810-9521-F

SI VOUS N'AVEZ PAS LE GUIDE D'INSTALLATION PROFESSIONNELLE, VEUILLEZ

VISITER WWW.BRINKMANN.NET OU APPELER AU (800) 527-0717.

AVERTISSEMENT

1

WE WANT YOU TO USE YOUR CONVERSION KIT FOR YOUR GRILL AS SAFELY AS

POSSIBLE. THE PURPOSE OF THIS SAFETY ALERT SYMBOL IS TO ATTRACT THE

ATTENTION TO POSSIBLE HAZARDS AS THE GRILL IS CONVERTED AND USED AS A

NATURAL GAS GRILL. WHEN YOU SEE THE SAFETY ALERT SYMBOL

PAY CLOSE ATTENTION TO THE INFORMATION WHICH FOLLOWS!

READ ALL SAFETY WARNINGS AND INSTRUCTIONS CAREFULLY

BEFORE CONVERTING AND OPERATING YOUR GRILL.

DANGER

IMPORTANT SAFETY WARNINGS

1. Do not store or use gasoline or other flammable liquids or vapors in the vicinity of this or any other appliance.

2. An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.

WARNING

Installer Company or Service Name:________________________________________________

Technician Name: ____________________________________Installation Date: ____________

Failure to follow the instructions as written, or installation by other than

a trained professional, will void all manufacturer warranties.

Model Number: ____________________________________

Serial Number:_____________________________________Date Purchased: ____________

IMPORTANT: Fill out product record information below and attach the conversion sticker

to your grill near the rating label after conversion has been made.

IF YOU SMELL GAS:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open Lid.

4. If odor continues, keep away from appliance and immediately call your gas supplier or your fire department.

2

TABLE OF CONTENTS

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in

death or serious injury.

WARNING: Be alert to the possibility of serious bodily injury if the instructions are not followed.

Be sure to read and carefully follow all of the messages.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in

minor or moderate injury.

INSTALLATION INFORMATION:

The installation of this appliance must be in accordance with:

All applicable local codes, or in the absence of local codes, either:

• National Fuel Gas Code ANSI Z223.1 NFPA 54

• Natural Gas and Propane Installation Code: CAN/CGA B149.1

• Natural Gas Installation Code: CAN/CGA B149.1 (Canada)

This kit converts your grill for natural gas use at 7 inch water column supply pressure. To check your pressure

contact your local natural gas company. If the supply pressure is different than 7 inch, contact a

professional

service technician

for assistance. Not for use with LP gas.

WARNING

• FOR OUTDOOR USE ONLY. DO NOT operate indoors or in an enclosed area such as a garage, shed

or breezeway.

• Use your grill OUTDOORS in a well ventilated space away from dwellings or other buildings to

prevent dangers associated with gas accumulation and toxic vapors. We recommend your grill be

situated at least 10 feet (3.1 m) from buildings.

• Maintain a minimum clearance of 36 inches (91 cm) between all sides of grill and walls or other

combustible material. DO NOT use grill under overhead unprotected combustible construction.

• DO NOT use or install this grill in or on a recreational vehicle and/or boat.

FOR GRILL WARRANTY REPLACEMENT PARTS, PLEASE VISIT US AT:

General Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Assembly Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–16

Converstion Instructions 810-8502-F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8

Converstion Instructions 810-8533-F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-12

Converstion Instructions 810-9521-F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-15

Connecting to Natural Gas Source. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Leak Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17–19

Pre-start Check List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Lighting Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Operating Grill and Helpful Hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21–25

Warning Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

3

WARNING

GENERAL WARNINGS

• Never use liquid propane gas in a unit designed for natural gas.

• Never use charcoal or wood briquette in a gas grill. Flavoring chips must be contained in a metal

smoking box to contain ash and prevent fires.

• Leak test all connections before first use, even if grill was purchased fully assembled

.

• Never check for leaks using a match or open flame.

CAUTION: Strong odors, colds, sinus congestion, etc. may prevent the detection of natural gas.

Use caution and common sense when testing for leaks.

• Always keep your gas grill free and clear of gasoline, lighter fluid, paint thinner, or other flammable

vapors and liquids or combustible materials.

• Always check the grill prior to each use as indicated in the "Pre-Start Check List" section of this

manual.

• Only use the specific orifice designated for your grill model. Always double check the millimeter

size on the side of the orifice tip prior to installation. Use of any other orifice could lead to personal

injury, property damage and void your grill warranty.

• DO NOT use back rotisserie burner when main burners are in use.

• DO NOT obstruct the flow of combustion or ventilation air.

• Never place more than 15 pounds on the side burner. DO NOT lean on the side burner shelf.

• Keep children and pets away from hot grill. DO NOT allow children to use or play near this grill.

• DO NOT leave the grill unattended while in use.

• DO NOT allow the gas hose to come in contact with hot surfaces.

• DO NOT allow grease from drain hole to fall on hose.

• Keep any electrical supply cords away from water or heated surfaces.

• Keep a fire extinguisher on hand acceptable for use with gas products. Refer to your local authority

to determine proper size and type.

• For household use only. DO NOT use this grill for anything other than its intended purpose.

• DO NOT use while under the influence of drugs or alcohol.

• Grill is hot when in use. To avoid burns:

• DO NOT attempt to move the grill.

• Lock the wheels so the unit does not accidentally move.

• Wear protective gloves or oven mitts.

• DO NOT touch any hot grill surfaces.

• DO NOT wear loose clothing or allow hair to come in contact with grill.

USE CAUTION AND COMMON SENSE WHEN OPERATING YOUR GAS GRILL.

FAILURE TO ADHERE TO THE SAFETY WARNINGS AND GUIDELINES IN THIS MANUAL

COULD RESULT IN SEVERE BODILY INJURY OR PROPERTY DAMAGE.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

Connection should be made by a professional service technician. Supply the technician with a copy of these

instructions. Incorrect connection can result in a gas leak with possibility of fire.

DANGER

Conversion Kit Sticker

This grill has

been converted

to natural gas.

1.32mm

Rotisserie Burner

1.32mm Valve Orifice x 1 Pc

(YELLOW)

Large

Stop Plate

x 7 Pcs.

Small

Stop Plate

x 2 Pc.

Gas Orifice Tool

Small Wrench

10’ Natural Gas Hose

Large Wrench

1.25mm

Side Burner

1.25mm Valve Orifice x 2 Pc

(GREEN)

Side Burner/Rotisserie Burner

1.35mm Valve Orifice x 2 Pc

(RED)

1.35mm 1.51mm

Rotisserie Burner

1.51mm Valve Orifice x 1 Pc

(BLUE)

L

S

4

PARTS CONTENTS

ASSEMBLY INSTRUCTIONS

YOU MUST BE A

PROFESSIONAL SERVICE TECHNICIAN

TO CONVERT THIS GRILL.

READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY

BEFORE ASSEMBLING OR OPERATING THE CONVERTED GRILL.

The following tools are required to assemble the Conversion Kit:

• Phillips Head Screwdriver • Adjustable Wrench • 3/4” Wrench

Inspect contents of the box to ensure all parts are included and undamaged.

FOR GRILL WARRANTY REPLACEMENT PARTS, PLEASE VISIT US AT:

5

Note: Make sure all control

knobs are in the off

position, LP tank valve is

closed and tank is

disconnected from

regulator and removed

from grill.

Step 1

Using an adjustable wrench to hold

the gas manifold connection secure,

use a 3/4” wrench to loosen the

hose connection nut. Replace

existing LP hose/regulator assembly

with natural gas 10ʼ hose assembly.

Tighten the connection carefully using

two wrenches.

Step 2

Remove two screws from side

burner bracket. Carefully lift side

burner up and away from valve

nozzle. Set aside for later use.

Step 3

Open hood and remove warming

rack, cooking grills and heat

distribution plates. Set aside for later

use.

810-8502-S MAIN & SIDE BURNERS

Gas Manifold Nut

Cooking Grills

Heat

Distribution

plates

10ʼ Natural Gas Hose

Warming Rack

CONVERSION

INSTRUCTIONS

810-8502-F

6

LP Gas Orifice

Gas Orifice Tool

Side View

Firebox Front Panel

Step 4

Remove screw from each burner

"foot" using a screwdriver. Carefully lift

each burner up and away from valve

openings. Set aside for later use.

Step 5

Use the gas orifice tool to remove the

LP brass orifice from main burner

valves through the hole on the firebox

front panel. Repeat this step for all

main and side burner valves in your

grill. The side burner valve orifice is

under the side shelf.

Note: All orifices of the grill are

double orifices type (LP gas

and natural gas). You only

remove the LP gas orifice tip.

CAUTION: Some parts may

contain sharp edges. Wear

protective gloves if necessary.

Step 6

Remove all the control knobs from the

control panel and set aside for later

use.

7

Step 7

Figure 1 shows valve stem and bezel

with the control knob removed. Take

seven large stop plates from the

component card and place them over

the main, side and sear burner valve

stems as illustrated (Figure 2). Verify

the tab and the stamped letter on the

stop plates face out. Replace control

knobs when finished.

WARNING: We recommend and

request that you do not remove the

control panel in order to access the

LP gas orifices. If you choose to

remove the control panel, you must

replace the control panel bezels

exactly as illustrated in Figure 2.

Failure to replace the bezels as

illustrated could lead to personal

injury and/or property damage.

Step 8

Carefully replace each main burner,

making sure burner openings slide

over valve nozzles. Attach each

burner using screws and nuts that

were set aside in Step 4. Replace

two screws in side burner bracket

that were set aside in Step 2.

Step 9

Replace warming rack, cooking

grills, heat distribution plates and

grease tray.

Figure 1

Stop Pin

L

Figure 2

Stop Plate

Tab

Cooking Grills

Heat

Distribution

plates

Warming Rack

8

810-8502-S SEAR BURNER

Note: It is helpful to keep the screws

with the components as they are

removed for ease of reassembly.

Step 1

Remove the two pre-attached bolts from

the sear burner orifice bracket using a

screwdriver. Set aside for later use.

Remove the LP orifice using the orifice

tool provided.

Note: Bending the hose could damage

the supply line.

Step 2

Attach the sear burner orifice bracket

using the two pre-attached bolts set aside

in Step 1.

Note: Follow directions in the leak

testing section of this manual

before using this grill.

Orifice Bracket

9

CAUTION: Some parts may

contain sharp edges. Wear

protective gloves if necessary.

WARNING: Only use the specific

orifice designated for your grill

model. Always double check the

millimeter size on the side of the

orifice tip prior to installation. Use

of any other orifice could lead to

personal injury, property damage

and void your grill warranty.

Note: Make sure all control

knobs are in the off

position, LP tank valve is

closed and tank is

disconnected from

regulator and removed

from grill.

Step 1

Using an adjustable wrench to hold

the gas manifold connection secure,

use a 3/4” wrench to loosen the

hose connection nut. Replace

existing LP hose/regulator assembly

with natural gas 10ʼ hose assembly.

Tighten the connection carefully using

two wrenches.

Step 2

Remove cotter pin from side burner

"foot". Carefully lift side burner up

and away from valve nozzle. Set

aside for later use.

Step 3

Open hood and remove warming

rack, cooking grills and heat

shields. Set aside for later use.

CONVERSION

INSTRUCTIONS

810-8533-F

Gas Manifold Nut

Cooking Grills

Heat Shields

10ʼ Natural Gas Hose

Cotter Pin

Warming Rack

10

Step 4

Remove screw from each burner

"foot" using a screwdriver. Carefully

lift each crossover channel and

burner up and away from valve

nozzles. Set aside for later use.

Step 5

Use the gas orifice tool to remove the

LP brass orifice from main burner

valves through the hole on the firebox

front panel. Repeat this step for all

main and side burner valves in your

grill. The side burner valve orifice is

under the side shelf.

CAUTION: Some parts may

contain sharp edges. Wear

protective gloves if necessary.

Step 6

Remove all the control knobs from the

control panel and set aside for later

use.

LP Gas Orifice

Gas Orifice Tool

Side View

Firebox Front Panel

11

Stop Pin

Figure 1

Stop Pin

Step 7

Figure 1 shows valve stem and bezel

with the control knob removed. Take

five large stop plates from the

component card and place them over

the main and side burner valve stems

as illustrated (Figure 2). Take the

small stop plate from the component

card and place it over the rotisserie

burner valve stem (Figure 3). Verify

the tab and the stamped letter on the

stop plates face out. Replace control

knobs when finished.

WARNING: We recommend and

request that you do not remove the

control panel in order to access the

LP gas orifices. If you choose to

remove the control panel, you must

replace the control panel bezels

exactly as illustrated in Figure 2.

Failure to replace the bezels as

illustrated could lead to personal

injury and/or property damage.

Step 8

Carefully replace each burner,

making sure burner openings slide

over LP gas orifices. Screw each

main burner "foot" down using

screwdriver and screws that were

set aside in Step 4. Replace cotter

pin in side burner “foot” that were

set aside in Step 2.

Step 9

Replace warming rack, cooking

grills, heat shields and grease tray.

L

S

Figure 2

Stop Plate

Cooking Grills

Heat Shields

Warming Rack

Tab

Figure 3

Stop Plate

Tab

12

Retaining Nut

810-8533-F ROTISSERIE BURNER

CAUTION: Only use specified

natural gas orifice for your grill.

Note: It is helpful to keep the

screws with the components

as they are removed for ease

of reassembly.

Step 10

Remove the three bolts from inside

grill back panel to gain access to

the rotisserie LP gas orifice on back

side of grill. Set aside for later use.

Step 11

Using an adjustable wrench to hold

the gas line secure, use the open

end wrench provided to loosen the

gas line retaining nut. With the

rotisserie gas supply line detached

from the housing, use two wrenches

to remove the LP brass orifice from

the gas supply line. Replace the LP

gas brass orifice with the proper

natural gas orifice.

(1.35 mm RED)

Note: Bending the hose could

damage the supply line.

Step 12

Reattach gas supply line to the

rotisserie housing by securing with

the retaining nut removed in Step

11.

Note: Leave the back panel off

until the end of

conversion and all gas leak

testing has been

completed.

Step 13

Re-install rotisserie cover using the

bolts that were set aside in Step 10.

Note: Follow directions in the leak

testing section of this manual

before using this grill.

1.35 mm

Existing Rotisserie LP

Gas Orifice

Replacement Rotisserie

Natural Gas Orifice

(identified by number)

Rotisserie Burner 1.35 mm (RED)

Brass Orifice

Cover Bolts

Inside View

Outside View

Cover Bolts

13

CAUTION: Some parts may

contain sharp edges. Wear protective

gloves if necessary.

Note: Make sure all control

knobs are in the off

position, LP tank valve is

closed and tank is

disconnected from

regulator and removed

from grill.

Step 1

Using an adjustable wrench to hold

the gas manifold connection secure,

use a 3/4” wrench to loosen the hose

connection nut. Replace existing LP

hose/regulator assembly with natural

gas 10ʼ hose assembly. Tighten the

connection carefully using two

wrenches.

Step 2

Remove cotter pin from side burner

"foot". Carefully lift side burner up and

away from valve nozzle. Set aside for

later use.

Step 3

Open hood and remove warming

rack, cooking grills and heat shields.

Set aside for later use.

CONVERSION

INSTRUCTIONS

810-9521-F

Cotter Pin

Warming Rack

Cooking Grills

Heat Shields

10ʼ Natural Gas Hose

Gas Manifold Nut

14

Step 4

Remove screw from each burner

"foot" using a screwdriver. Carefully lift

each burner up and away from valve

openings. Set aside for later use.

Step 5

Use the gas orifice tool to remove the

LP brass orifice from main burner

valves through the hole on the firebox

front panel. Repeat this step for all

main and side burner valves in your

grill. The side burner valve orifice is

under the side shelf.

Note: All orifices of the grill are

double orifices type (LP gas

and natural gas). You only

remove the LP gas orifice tip.

CAUTION: Some parts may

contain sharp edges. Wear protective

gloves if necessary.

Step 6

Remove all the control knobs from the

control panel and set aside for later

use.

LP Gas Orifice

Gas Orifice Tool

Side View

Firebox Front Panel

15

Step 7

Figure 1 shows valve stem and bezel

with the control knob removed. Take

six large stop plates from the

component card and place them over

the valve stems as illustrated

(Figure 2). Verify the tab and the

stamped letter on the stop plates face

out. Replace control knobs when

finished.

WARNING: We recommend and

request that you do not remove the

control panel in order to access the

valve tips. If you choose to remove

the control panel, you must replace

the control panel bezels exactly as

illustrated in Figure 2. Failure to

replace the bezels as illustrated could

lead to personal injury and/or

property damage.

Step 8

Carefully replace each burner,

making sure burner openings slide

over valve nozzles. Screw each main

burner "foot" down using screwdriver

and screws that were set aside in

Step 4. Replace cotter pin in side

burner “foot” that was set aside in

Step 2.

Step 9

Replace warming rack, cooking grills,

heat shields and grease tray.

Note: Follow directions in the leak

testing section of this manual

before using this grill.

Warming Rack

Cooking Grills

Heat Shields

Stop Pin

L

Figure 2

Figure 1

Stop Plate

Tab

16

CONNECTING YOUR GRILL TO THE NATURAL GAS SOURCE

1. Coat pipe nipple with gas resistant teflon tape or pipe dope. Tighten quick-disconnect coupling onto

pipe nipple that leads to natural gas supply (Figure A).

2. After grill is completely assembled, make sure natural gas supply valve is “OFF” and then connect

natural gas hose to socket. Push sleeve back on socket (Figure B) and insert plug until sleeve snaps

forward, locking plug into socket. Be sure to leak test these connections prior to use.

Pipe nipple

Quick-disconnect

coupling

Plug

Push sleeve back to attach

Sleeve

Socket

Natural gas supply

Hose

Insert cover when hose is disconnected

DISCONNECTING YOUR GRILL FROM THE NATURAL GAS SOURCE

1. Turn natural gas supply valve “OFF”

2. To disconnect, push sleeve back and pull plug out of sleeve.

(Figure A)

(Figure B)

Supply valve

Pipe Fitting

Flare Fitting

When attaching the quick disconnect to your natural gas supply line, use a pipe fitting,

DO NOT use a flare fitting.

AVOID HARD METAL PIPING

• DO NOT use hard metal piping of any kind to connect this converted natural gas grill. Use only

natural gas hose specified by the manufacturer. Using hard metal piping or convoluted metal

tubing is an unsafe practice. Movement of the grill can cause breakage of metal pipe.

WARNING

LEAK TESTING:

To prevent fire or explosion hazard:

• DO NOT smoke or permit ignition sources in the area while conducting a leak test.

• Perform test OUTDOORS only in a well ventilated area.

• Never perform a leak test with a match or open flame.

• Never perform a leak test while the grill is in use or while grill is still hot.

DANGER

WHEN TO PERFORM A LEAK TEST:

• After assembling or converting your natural gas grill and before lighting for the first time, even if

purchased fully assembled.

• Any time the gas components are replaced.

• Any time your grill has been moved.

• At least once per year or if your grill has not been used for more than 60 days.

WARNING

• Never use your grill without leak testing all gas connections and hoses. See the section on

“Leak Testing” in this manual for proper procedures.

• Visually inspect the hose assembly prior to each use for evidence of damage, excess wear or

deterioration. If found, replace the assembly before using your grill. Only the manufacturer's

supplied replacement should be used.

• During assembly or conversion to natural gas, keep the supply hoses free of kinks and/or

damage.

WARNING

17

18

CHECKING FOR LEAKS:

1. Create a mixture of 50% water and 50% liquid dishwashing soap.

2. Open the lid.

3. Ensure all control knobs are set to the "OFF" position.

4. Ensure gas hose is tightly connected to gas source.

5. Turn on the fuel supply on at the source.

6. Apply the soap water mixture to the following:

Note: Some Grill models will have different connections than illustrated.

Hose connection to gas manifold.

Gas supply hose connection to

side burner valve assembly.

Side burner valve stem cap. (if applicable)

Side burner connection to hose. (if applicable)

The full length of gas supply hose.

Rotisserie orifice connection. (if applicable)

Rotisserie supply line connection to rotisserie valve assembly. (if applicable)

Note:

Rotisserie gas supply line can be gas leak tested by removing the grease tray and applying

soap water mixture from under the control panel.

Quick disconnect coupler.

H

G

F

E

D

C

B

A

Before first use, check gas supply line connection to rotisserie burner

valve (under control panel) and gas supply line connection to the

orifice (back of grill body). Push in and turn the rotisserie control knob

to “HIGH” and hold in the knob when performing gas leak test on

rotisserie valve. Allow gas to dissipate when finished.

CAUTION:

H

GF

A

B

C

D

E

WARNING

7. Check each place listed (A–H) for growing bubbles which indicates a leak.

8. Turn off gas supply at source.

9. Turn on control knobs to release gas pressure in hose.

10. Turn control knobs to "OFF" position.

11. Tighten any leaking connections.

12. Repeat soapy water test until no leaks are detected.

13. Turn off gas supply at source until you are ready to use your grill.

14. Wash off soapy residue with cold water and towel dry.

15. Wait 5 minutes to allow all gas to evacuate the area before lighting grill.

CAUTION: DO NOT use the grill if leaks cannot be stopped.

Note: The leak test must be performed in an area that has adequate lighting in order to see if

bubbles are developing.

Property damage, bodily harm, severe burns, and death could result from failure to follow these

safety steps. These steps should be performed after the grill has been assembled and prior to each

use. DO NOT operate this grill until you have read and understand ALL of the warnings and

instructions in this manual.

PRE-START CHECK LIST:

• Ensure that the grill is properly assembled.

• Inspect the gas supply hose for burns, chaffing, kinks, and proper routing before each use. If it is

evident there is excessive abrasion or wear, or the hose is cut, it must be replaced prior the grill being

used.

• Leak check all gas connections and hose. See section on "Leak Testing".

• Ensure that all electrical supply cords are properly grounded. Keep any electrical supply cord and the

fuel supply hose away from any heated surfaces. Hose should be at least 3 inches from hot surfaces.

• Position your grill on level ground in a well ventilated location, a safe distance from combustible

materials, buildings and overhangs.

• Properly place the empty grease tray under the grease drain hole in the bottom of the

grill to catch grease during use.

• DO NOT obstruct the flow of combustion and ventilation air.

Watch For Bub bles

E

19

La page charge ...

Brinkmann Natural Gas Conversion Kit Guide d'installation

Brinkmann Natural Gas Conversion Kit Guide d'installation

dans d''autres langues

Documents connexes

Autres documents