Simplicity 020667V-00 Manuel utilisateur

Marque: Simplicity

Modèle: 020667V-00

Catégorie: Nettoyeurs haute pression

Taper: Manuel utilisateur

Manual No. 80102966 Rev A

Model Number _____________________________

Revision __________________________________

Serial Number ______________________________

Date Purchased ____________________________

(800) 743-4115

BRIGGSandSTRATTON.COM

Electric Pressure Washer

Operator’s Manual

2 BRIGGSandSTRATTON.COM

Thank you for purchasing this quality-built Briggs & Stratton® electric pressure washer. We are pleased that you’ve

placed your confidence in the Briggs & Stratton brand. When operated and maintained according to the instructions in this

manual, your Briggs & Stratton electric pressure washer will provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with electric pressure

washers and how to avoid them. Because Briggs & Stratton does not necessarily know all the applications this electric

pressure washer could be used for, it is important that you read and understand these instructions thoroughly before

attempting to start or operate this equipment. Save these original instructions for future reference.

This electric pressure washer requires final assembly before use. Refer to the Assembly section of this manual for

instructions on final assembly procedures. Follow the instructions completely.

Where to Find Us

You never have to look far to find Briggs & Stratton support and service for your electric pressure washer. There are many

Briggs & Stratton authorized service dealers worldwide who provide quality service. You can also contact Briggs & Stratton

Customer Service by phone at (800) 743-4115, or on the Internet at BRIGGSandSTRATTON.COM.

To ensure prompt and complete warranty coverage, register your product online at www.onlineproductregistration.com.

Table of Contents

Operator Safety.............................. 3

Assembly................................... 6

Features and Controls ........................ 8

Operation................................... 9

Maintenance ...............................12

Storage ...................................13

Troubleshooting ............................14

Specifications ..............................15

Warranty ..................................16

Operator Safety

Equipment Description

Every effort has been made to ensure that the information

in this manual is accurate and current. However, we

reserve the right to change, alter, or otherwise improve the

product and this document at any time without prior notice.

This spark ignition system complies with the Canadian

Standard CAN ICES-2/NMB-2.

Ground Fault Circuit Interrupter Protection

This pressure washer is provided with a ground-fault

circuit-interrupter (GFCI) built into the plug of the power

supply cord. This device provides additional protection

from the risk of electric shock. Should replacement of

the plug or cord become necessary, use only identical

replacement parts that include GFCI protection.

Automatic Shut-Off

The electric pressure washer is equipped with a sensor that

will detect that water flow has stopped when releasing the

spray gun trigger. The sensor will cause the motor to shut off

for as long as the spray gun trigger is released.

PowerFlow+™ Technology

One easy twist. 7 ways to clean.

PowerFlow+ technology provides both high pressure to

lift dirt and high flow to easily wash it away. The high flow

mode enhances the cleaning experience by providing

extended reach, power soaping, and faster rinsing

capabilities – things standard pressure washers can’t do.

The force behind PowerFlow+ is in the pump with two

separate cleaning modes, high pressure and high flow.

These dual modes can easily be changed via the 7-in-1

nozzle without changing nozzle tips. The high pressure

mode delivers up to 2000 PSI (pounds square inch) and is

ideal for cleaning the toughest stains, mildew, and grime

from decks, driveways, and siding. The high flow mode

delivers up to 3.5 GPM (gallons per minute) to power-rinse

away dirt, soap, and debris. The high flow mode is also

great for washing delicate surfaces such as patio furniture,

vehicles, and children’s outdoor play sets and toys.

If the motor continues to run when the spray gun trigger is

released or locked, DO NOT USE THE MACHINE. Call the

electric pressure washer helpline at (800) 743-4115 for

assistance.

NOTICE The electric pressure washer is equipped with a

main power ON/OFF switch. The switch should always be

moved to the OFF position (0) when the electric pressure

washer is not being used to prevent possible damage.

Motor Overload

The electric motor in this electric pressure washer is

equipped with an overload protection device (thermostat).

This device will automatically shut off the motor if the motor

overheats or draws excessive current.

If the overload protection device is tripped, disconnect the

power supply by turning the master ON/OFF switch to the

OFF (0) position. Let unit cool for 30 minutes. Then turn

the master ON/OFF switch to the ON (I) position to resume

operation.

Important Safety Information

Please read and understand this entire manual before

attempting to assemble, operate or service the product.

Follow the maintenance instructions specified in this

manual. If you have any questions regarding the product,

please call customer service at (800) 743-4115, 8 a.m. -

5 p.m., CST, Monday - Friday.

Safety Symbols and Meanings

The safety alert symbol indicates a potential personal

injury hazard. A signal word (DANGER, WARNING, or

CAUTION) is used with the alert symbol to designate a

degree or level of hazard seriousness. A safety symbol

may be used to represent the type of hazard. The signal

word NOTICE indicates information considered important,

but not hazard-related.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided,

could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided,

could result in minor or moderate injury.

NOTICE indicates information considered important, but

not hazard-related.

WARNING Failure to read and follow the operator’s

manual and all operating instructions before

using could result in death or serious injury.

• Read this manual carefully and become familiar with

your electric pressure washer. Know its applications, its

limitations, and any hazards involved.

Chemical Burn

Electrical Shock

Slippery Surface Fall

Flying Objects

Read Manual

Projectile

Fluid Injection

Fire

4 BRIGGSandSTRATTON.COM

WARNING Use of electric pressure washer could

create puddles and slippery surfaces.

Risk of kickback. Spray gun could

kickback causing you to fall resulting in

death or serious injury.

• Operate the electric pressure washer from a

stable surface.

• Do not overreach or stand on unstable support. Keep

good footing and balance at all times.

• The cleaning area should have adequate slopes

and drainage to reduce the possibility of a fall due to

slippery surfaces.

• Be extremely careful if you must use the electric

pressure washer from a ladder, scaffolding, or any

other similar location.

• Firmly grasp spray gun with both hands when using

power spray modes to avoid injury when spray gun

kicks back.

WARNING The high pressure stream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting in serious

injury and possible amputation.

Spray gun traps high water pressure, even when motor

is stopped and water is disconnected, which could result

in serious injury.

• NEVER aim spray gun at people, animals, or plants.

• ALWAYS point spray gun in safe direction, squeeze

spray gun trigger to release high pressure, every time

you turn off pressure washer.

WARNING Risk of eye or bodily injury. Spray could

splash back, propel objects or cause

internal harm resulting in serious injury.

• Always wear indirect vented (chemical splash) safety

goggles marked to comply with ANSI Z87.1 when using

or in vicinity of this equipment. NEVER substitute safety

glasses or dry-condition goggles for indirect vented

safety goggles.

• Know how to stop the pressure washer and bleed

pressure quickly. Be thoroughly familiar with the

controls.

• DO NOT allow CHILDREN to operate the electric

pressure washer.

• Keep operating area clear of all persons.

• Inspect high pressure hose before each use. NEVER

repair high pressure hose; replace it.

• DO NOT repair leaking connections with sealant of any

kind; replace o-rings and gaskets.

• Keep hose connected to electric pressure washer and

spray gun while system is pressurized.

• ALWAYS point spray gun in safe direction while system

is pressurized and squeeze spray gun trigger to release

high pressure, every time you turn off the pressure

washer.

• DO NOT aim spray gun at people or animals.

• DO NOT

drink from hose connected accessories.

• DO NOT secure spray gun in open position.

• DO NOT leave spray gun unattended while the electric

pressure washer is in ON (I) position.

• DO NOT use a spray gun which does not have a trigger

lock or trigger guard in place and in working order.

• Always be certain spray gun and accessories are

correctly attached.

• Stay alert – watch what you are doing.

• DO NOT operate the product when fatigued or under

the influence of alcohol or drugs.

• Close supervision is necessary when this product is

used near children.

WARNING Risk of electrocution. Use of an

extension cord could cause electric shock or

burn resulting in death or serious injury.

• DO NOT use an extension cord with this electric

pressure washer. Your home’s electrical circuit

receptacle or extension cord may not provide lifesaving

ground-fault circuit-interruption protection.

WARNING Risk of electrocution. Contacting both

power conductors, at the same time could

cause electric shock or burn resulting in death

or serious injury.

• Connect only to a properly grounded outlet. DO NOT

remove ground pin from plug.

• Inspect cord before each use, DO NOT use if cord is

damaged.

• The product is equipped with a ground fault circuit

interrupter (GFCI) built into the power cord plug. If

replacement of the plug or cord is required, use only

identical replacement parts.

• Keep all connections dry and off the ground.

• DO NOT touch plug with wet hands.

• DO NOT run cord through doorways, windows, holes in

ceilings, walls, or floors.

• DO NOT walk on cord.

• DO NOT drive over, drag or place objects over cord.

• DO NOT spray near power source.

WARNING Risk of fire. Spraying flammable liquids

could result in death or serious injury.

• DO NOT spray flammable liquids.

WARNING Risk of fire. Overheated cord could result

in death or serious injury.

• Uncoil cord completely prior to use.

• DO NOT cover cord with any material.

NOTICE High pressure spray could damage fragile

items including glass.

• DO NOT point spray gun at glass when using 0° nozzle

setting or red nozzle.

• NEVER aim spray gun at plants.

NOTICE You must protect your unit from freezing

temperatures.

• Failure to do so will permanently damage your pump

and render your unit inoperable.

• Freeze damage is not covered under warranty.

NOTICE Improper treatment of electric pressure washer

could damage it and shorten its life.

• If you have questions about intended use, ask dealer or

contact authorized service center.

• DO NOT operate units with broken or missing parts, or

without protective housing or covers.

• DO NOT by-pass any safety device on the electric

pressure washer.

• DO NOT modify the electric pressure washer in any

way.

• DO NOT move the electric pressure washer by pulling

on hoses. Move unit using the transport handle

supplied.

• Use ONLY branded accessories intended for use with

this product.

WARNING Chemical Burn Hazard.

Chemicals could cause burns resulting

in death or serious injury.

• Always wear indirect vented (chemical splash) safety

goggles marked to comply with ANSI Z87.1 when using

chemicals.

• DO NOT substitute safety glasses or dry-condition

goggles for indirect vented safety goggles.

• DO NOT use caustic liquid with electric pressure

washer.

• Use ONLY pressure washer safe detergents/soaps.

Follow all manufacturers instructions.

WARNING

This product contains lead and lead

compounds, known to the state of California to cause

birth defects or other reproductive harm. Wash

your hands after handling this product. Cancer and

Reproductive Harm - www.P65Warnings.ca.gov.

6 BRIGGSandSTRATTON.COM

Assembly

Read entire operator’s manual before you

attempt to assemble or operate your new

electric pressure washer.

Your electric pressure washer requires some assembly

but is quickly ready for use. If you have any problems with

the assembly of your electric pressure washer, please call

the electric pressure washer helpline at (800) 743-4115. If

calling for assistance, please have the model, revision, and

serial number from the identification label available.

Unpack Electric Pressure Washer

1. Remove everything from carton.

2. Raise handle (A) to upright position by pulling up latch

on each side of handle. Push latches (B) down to

secure handle in place.

NOTICE The unit is equipped with a foldable handle. The

handle can be folded down for storage. See Final Storage

Procedures.

3. Ensure you have all included items prior to assembly.

Items Included in the Carton

• Main unit

• Operator’s manual

• Spray gun

• High pressure hose

• Spray wand with Quick Connect (QC)

• 7-in-1 nozzle

• Red high pressure nozzle

Check all contents. If any parts are missing or damaged, call

the electric pressure washer helpline at (800) 743-4115.

Become familiar with each component before assembling

the electric pressure washer. Identify contents with the

illustration shown in Features and Controls.

Lubricate O-Rings

Lubrication of o-rings is extremely important for installation

and operation. The use of a lubricant (petroleum or

synthetic grease) during assembly helps seat o-rings

properly and provides an improved seal. It also helps

protect the o-ring from damage by abrasion, pinching or

cutting and extends the life of the o-ring.

NOTICE ALWAYS apply a small amount of lubricant on

o-rings prior to assembling the garden hose to the pump

(C), high pressure hose (D), spray wand (E) and spray

gun (F).

Lubricate all connections shown below, following these

instructions:

1. Inspect and clean connecting surfaces prior to

lubrication and assembly.

2. Use lubricants sparingly during assembly; a light film

is all that is required.

3. Use a small brush or cotton swab to apply grease

directly to o-rings where they are not accessible (QC

fitting, M22 fitting).

Connect Hose and Water Supply to Pump

NOTICE DO NOT run the pump without the water supply

connected and turned on.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

1. Uncoil high pressure hose (A) and attach black end of

hose to base of spray gun (B). Tighten by hand.

2. Attach blue end of high pressure hose (A) to high

pressure outlet (C) on pump. Tighten by hand.

3. Run water through your garden hose for 30 seconds

to clean out any debris.

NOTICE DO NOT siphon standing water for the water

supply. Use ONLY cold water (less than 100°F (38°C)).

4. Before connecting garden hose (D) to water inlet (E),

inspect inlet screen (F). Clean screen if it contains

debris or have it replaced if damaged. DO NOT run

pressure washer if inlet screen is damaged.

NOTICE Using a One Way Valve (vacuum breaker or

check valve) at pump inlet could cause pump or inlet

connector damage.

• There MUST be at least 10 ft. (3 m) of unrestricted

garden hose between the pressure washer inlet and any

device, such as a vacuum breaker or check valve.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

5. Connect the garden hose (D) (not to exceed 50 ft. (15

m) in length) to the water inlet (E). Tighten by hand.

Connect Spray Wand and 7-in-1 Nozzle

1. Turn ON water, point gun in a safe direction, press

trigger lock button (G), then squeeze trigger to purge

pump system and spray gun of air and impurities.

2. Attach spray wand to spray gun. Tighten by hand.

3. Pull back on collar of spray wand, insert 7-in-1 nozzle

and release collar. Tug on 7-in-1 nozzle to make sure

it is securely in place. See How to Use Nozzles.

Checklist Before Starting Pump Motor

Review the unit’s assembly to ensure you have performed

all of the following.

1. Be sure to read Operator Safety and Operation before

using the electric pressure washer.

2. Check for properly tightened hose connections.

3. Check to make sure there are no kinks, cuts, or

damage to hoses.

4. Provide a proper water supply at an adequate flow.

5. Plug electrical power cord into a dedicated electrical

circuit rated for 120 Volts AC at 15 Amps that is

properly installed in accordance with all local codes and

ordinances. Check that circuit is not used to supply any

other electrical needs.

D E

8 BRIGGSandSTRATTON.COM

Features and Controls

Read the Operator’s Manual and safety rules before operating your electric pressure washer.

Compare the illustrations with your electric pressure washer to familiarize yourself with the locations of various

controls and adjustments. Save this original manual for future reference.

A - Spray Gun — Controls the application of water onto

cleaning surface with trigger device. Includes trigger lock.

B - Identification Label — Provides model and serial

number of pressure washer. Please have these readily

available if calling for assistance.

C - Electric Cord with GFCI — The electric pressure

washer and operator is protected by a ground fault circuit

interrupter (GFCI).

D - High Pressure Hose — Connect one end to high

pressure water outlet and the other end to spray gun.

E - Spray Wand with Quick Connect — Allows you to

switch between 7-in-1 nozzle and optional accessories.

F - Detergent Tank — Use to hold up to 40 fl. oz. (1.2 l) of

pressure washer safe detergent.

G - Water Supply Inlet — Connect to water supply using

a 50 ft. (15.24 m) maximum garden hose.

H - Master ON/OFF Toggle Switch — Turn switch to ON

(I) position to start pressure washer. Turn switch to OFF (0)

position to stop pressure washer.

J - High Pressure Outlet — Connection for high pressure

hose.

K - 7-in-1 Nozzle — Contains seven different spray

pattern nozzles for various applications.

L - Warning Label — Identifies hazards to be avoided

when using your pressure washer.

Operation

How to Start Your Electric Pressure Washer

Follow the instructions below in the order presented. If

you have any problems operating your electric pressure

washer, please call the electric pressure washer helpline at

(800) 743-4115.

1. Place the electric pressure washer near an outside

water source capable of supplying water at a flow rate

greater than 5.0 gallons per minute (18.9 l) and 25-75

psi (1.72-5.17 bar) at the electric pressure washer end

of garden hose. DO NOT siphon supply water.

2. Connect garden hose to water inlet.

3. Check that high pressure hose is tightly connected to spray

gun and high pressure outlet. See Assembly section.

NOTICE If hose connections start leaking during use,

shut down unit as described in steps 1-5 of How to Stop

Your Electric Pressure Washer. Remove hose completely

and reinstall hand tight. Failure to completely remove

hose could damage o-ring and cause hose connection to

continue leaking. If o-ring becomes damaged, replace.

NOTICE DO NOT run the pump without the water supply

connected and turned on.

• Damage to equipment resulting from failure to follow

this instruction will void warranty.

4. Turn ON water, point gun in a safe direction, press

trigger lock button and squeeze trigger to purge pump

system of air.

5. Install spray wand and 7-in-1 nozzle onto spray gun.

See Assembly section.

NOTICE The unit can be operated in vertical or horizontal

positions.

6. Turn master ON/OFF switch (A) to OFF (0) position.

7. Plug electrical power cord into a dedicated electrical

circuit rated for 120 Volts AC at 15 Amps that is

properly installed in accordance with all local codes and

ordinances. Circuit is not to supply any other electrical

needs. The indicator light on the GFCI should be ON.

NOTICE The indicator light must be ON for the electric

pressure washer to operate.

8. Press TEST button (B). The indicator light (C) should

be OFF.

9. Press RESET button (D). The indicator light (C)

should be ON.

NOTICE DO NOT use the electric pressure washer if

above test fails.

10. Turn master ON/OFF switch to ON (I) position.

11. Point gun in a safe direction, press trigger lock button

and squeeze trigger.

The electric pressure washer motor will start and stop as

spray gun trigger is depressed and released.

The electric pressure washer is now ready for use.

Instructions for use of the supplied accessories are given

later in this section.

WARNING Risk of electrocution. Use of an

extension cord could cause electric shock or

burn resulting in death or serious injury.

• DO NOT use an extension cord with this electric

pressure washer. Your home’s electrical circuit

receptacle or extension cord may not provide lifesaving

ground-fault circuit-interruption protection.

WARNING Risk of electrocution. Non-operating

ground fault circuit interrupter (GFCI) could

result in death or bodily injury. If indicator light

does not stay ON after test and reset, do not

use GFCI.

WARNING Risk of eye injury. Spray could splash

back or propel objects resulting in serious

injury. Always wear indirect vented (chemical

splash) safety goggles marked to comply with

ANSI Z87.1 when using or in vicinity of this equipment.

NEVER substitute safety glasses or dry-condition

goggles for indirect vented safety goggles.

10 BRIGGSandSTRATTON.COM

How to Stop Your Electric Pressure Washer

The electric pressure washer motor runs only when the

trigger is engaged. To stop the electric pressure washer

and turn off the motor:

1. Release spray gun trigger.

2. Turn master ON/OFF switch to OFF (0) position.

NOTICE Releasing the trigger will shut off the motor but

does not shut off electrical power to the unit.

3. Turn off water supply.

4. ALWAYS point spray gun in a safe direction, press

trigger lock button and squeeze trigger to relieve built

up pressure in the unit.

5. Disconnect GFCI plug from outlet.

How to Use Nozzles

7-in-1 Nozzle

The 7-in-1 nozzle allows you to switch between seven

different spray pattern nozzles. Release trigger on spray

gun to engage safety lock before changing spray patterns.

The spray patterns vary as shown below.

1. Select desired spray pattern:

2. Turn dial until desired spray pattern lines up with

arrow on 7-in-1 nozzle.

Red High Pressure Nozzle

The red high pressure nozzle gives you the most cleaning

power by producing the highest pressure.

Usage Tips

• For most effective cleaning, keep nozzle from 8 to

24 inches away from cleaning surface.

• If you get too close, especially using a high pressure

spray pattern nozzle, you may damage surface being

cleaned.

• Do Not get closer than 6 inches (15 cm) when

cleaning tires.

WARNING The high pressure stream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting in serious

injury and possible amputation.

Spray gun traps high water pressure, even when motor

is stopped and water is disconnected, which could result

in serious injury.

• Keep high pressure hose connected to pump and

spray gun while system is pressurized.

• ALWAYS point spray gun in safe direction, squeeze

spray gun trigger to release high pressure, every time

you turn off pressure washer.

High Pressure:

High Flow:

Applying Detergent

To apply detergent, follow these steps:

1. Review use of nozzles shown in How to Use Nozzles.

2. Prepare your detergent solution as required by job to

be performed.

3. Remove cap from detergent tank and fill with

detergent solution. Replace cap.

4. Make sure one of the soap spray pattern nozzles is

selected on 7-in-1 nozzle.

NOTICE Detergent cannot be applied with non soap

nozzle setting.

5. Make sure garden hose is connected to water inlet

and high pressure hose is connected to spray gun and

high pressure outlet. Turn on water.

6. Start the pressure washer as instructed in How to

Start Your Electric Pressure Washer.

7. Apply detergent to a dry surface, starting at lower

portion of area to be washed and work upward using

long, even, overlapping strokes.

NOTICE High water supply pressure may not allow

detergent to flow. See Troubleshooting.

8. Allow detergent to “soak in” for 3-5 minutes before

washing and rinsing. Reapply as needed to prevent

surface from drying. To prevent streaking, Do Not

allow detergent to dry on surface.

Electric Pressure Washer Rinsing

1. Select desired high pressure nozzle following

instructions How to Use Nozzles.

2. Keep spray gun a safe distance from area you plan to

spray.

3. Apply a high pressure spray to a small area and then

check surface for damage. If no damage is found, you

can assume it is okay to continue rinsing.

4. Start at top of area to be rinsed, working down with

same overlapping strokes as you used for cleaning.

Other Cleaning Tips

• NEVER leave the electric pressure washer unattended

while it is plugged into an electrical outlet and while

water is supplied to the equipment.

• If you have the nozzle too far away from the surface

being washed, the cleaning may not be as effective.

How to Store Accessories

The unit is equipped with places to store your high

pressure hose, spray gun, spray wand, 7-in-1 nozzle and

power cord. The red high pressure nozzle can be stored

on end of spray wand. Identify all accessories with the

illustrations in Features and Controls.

WARNING Chemical Burn Hazard.Chemicals could

cause burns resulting in death or serious

injury.

• Always wear indirect vented (chemical splash) safety

goggles marked to comply with ANSI Z87.1 when using

chemicals.

• DO NOT substitute safety glasses or dry-condition

goggles for indirect vented safety goggles.

• DO NOT use caustic liquid with electric pressure washer.

• Use ONLY pressure washer safe detergents/soaps.

Follow all manufacturers instructions.

WARNING Risk of kickback.

Spray gun could kickback causing you to fall

resulting in death or serious injury.

• Operate the electric pressure washer from a

stable surface.

• Be extremely careful if you must use the electric

pressure washer from a ladder, scaffolding, or any

other similar location.

• Firmly grasp spray gun with both hands when using

power spray modes to avoid injury when spray gun

kicks back.

12 BRIGGSandSTRATTON.COM

Maintenance

General Recommendations

Regular maintenance will improve the performance and

extend the life of the electric pressure washer.

The electric pressure washer’s warranty does not cover

items that have been subjected to operator abuse or

negligence. To receive full value from the warranty, the

operator must maintain the electric pressure washer as

instructed in this manual, including proper storage.

NOTICE Should you have questions about replacing

components on your electric pressure washer, please call

(800) 743-4115 for assistance.

NOTICE Your electric pressure washer was designed

and intended to be used with POWERflow+ components

ONLY. Using components that are not designed for

POWERflow+ will cause your pressure washer to not

function optimally.

Before Each Use

1. Clean debris.

2. Check water inlet screen for debris or damage.

3. Check high pressure hose for leaks.

4. Check spray gun operation.

Electric Pressure Washer Maintenance

Clean Debris

Daily or before use, clean accumulated debris from electric

pressure washer. Inspect cooling air slots and openings on

the front, rear and bottom of the electric pressure washer.

These openings must be kept clean and unobstructed.

The electric pressure washer parts should be kept clean to

reduce the risk of overheating and ignition of accumulated

debris.

• Use a damp cloth to wipe exterior surfaces clean.

NOTICE Improper treatment of the electric pressure

washer can damage it and/or shorten its life.

• DO NOT insert any objects through cooling slots.

Check and Clean Water Inlet Screen

Examine the screen on the unit’s water inlet. Clean it if the

screen is clogged or replace it if screen is damaged.

Check High Pressure Hose

The high pressure hose can develop leaks from wear,

kinking, or abuse. Inspect the hose each time before

using it. Check for cuts, leaks, abrasions or bulging of

cover, damage or movement of couplings. If any of these

conditions exist, replace the hose immediately.

WARNING The high pressure stream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting in serious

injury and possible amputation.

• NEVER repair high pressure hose. Replace it.

• Replacement hose rating MUST equal or exceed

maximum pressure rating of unit.

Check Spray Gun

Examine hose connection to spray gun and make sure

it is secure. Test trigger by pressing trigger lock button

and making sure trigger “springs back” into place when

you release it. You should not be able to press trigger

without pressing trigger lock button. Replace spray gun

immediately if it fails any of these tests.

Nozzle Maintenance

Excessive pump pressure can cause a pulsing sensation

felt while squeezing the spray gun trigger. The principal

cause of excessive pump pressure is a nozzle clogged or

restricted with foreign materials such as dirt, etc. A clogged

nozzle could lead to pump cycling ON/OFF or not turning

on even when there is some flow.

To correct the problem, immediately clean the nozzle by

following these instructions:

1. Turn master ON/OFF switch to OFF (0) position.

Remove power cord plug from electrical outlet.

2. Disconnect water supply at the electric pressure

washer.

3. ALWAYS point spray gun in a safe direction, press

trigger lock button and squeeze spray gun trigger to

release retained high water pressure.

4. Remove 7-in-1 nozzle from end of spray wand.

5. Use small paper clip to free any foreign material

clogging or restricting any of the nozzles.

6. Using a garden hose, remove additional debris by

back flushing water through spray wand. Back flush

between 30 to 60 seconds.

7. Reinstall 7-in-1 nozzle into spray wand.

8. Reconnect spray wand to spray gun.

WARNING The high pressure stream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting in serious

injury and possible amputation.

Spray gun traps high water pressure, even when motor

is stopped and water is disconnected, which could result

in serious injury.

• Keep high pressure hose connected to pump and

spray gun while system is pressurized.

• ALWAYS point spray gun in safe direction, squeeze

spray gun trigger to release high pressure, every time

you turn off pressure washer.

9. Make sure garden hose is connected to water inlet.

Check that high pressure hose is connected to spray

gun. Turn on water.

10. Plug power cord into electrical outlet and turn master

ON/OFF switch to pressure washer ON (I) position.

11. Test the electric pressure washer by operating with

each nozzle setting.

Pump and Motor Maintenance

The electric pressure washer does not require any

maintenance to the pump or motor. Both assemblies

are pre-lubricated and sealed, requiring no additional

lubrication ever.

After Each Use

Water should not remain in the unit for long periods of time.

Sediments or minerals can deposit on pump parts and

“freeze” pump action. Follow these procedures after every

use:

1. To ensure detergent tank does not drain during

storage, run electric pressure washer with a soap

spray nozzle until tank is empty.

2. Add 0.5 liter of clean fresh water to detergent tank, run

electric pressure washer with a soap nozzle. Flush for

one or two minutes.

3. Turn master ON/OFF switch to OFF (0) position.

Remove power cord plug from electrical outlet.

4. Turn off water supply. Point gun in a safe direction,

press trigger lock button and squeeze trigger to relieve

trapped pressure.

5. Disconnect garden hose from water inlet. Disconnect

high pressure hose from spray gun and high pressure

outlet.

6. Drain water from hose and spray gun, then use a cloth

or equivalent to wipe off all exterior surfaces.

7. Drain water from pump by tipping unit onto its right

side (water inlet and high pressure outlet facing down)

for two minutes.

8. Wrap high pressure hose and power cord on hook.

9. Store spray gun, spray wand, and 7-in-1 nozzle in

provided storage areas. Store red high pressure

nozzle on end of spray wand.

10. Store unit in a clean, dry area.

11. If storing for more than 30 days see Winter or Long

Term Storage.

Winter or Long Term Storage

Follow steps 1-9 in After Each Use.

NOTICE Water left in pump could freeze and permanently

damage pump. Freeze damage is not covered under

warranty.

Protecting the Pump

To protect the pump from damage caused by mineral

deposits or freezing, use Pump Saver™, Model 6039, to

treat pump. This prevents freeze damage and lubricates

plunger and seals.

NOTICE Pump Saver is available as an optional

accessory. It is not included with the electric pressure

washer. Contact the nearest authorized service center to

purchase Pump Saver.

NOTICE You must protect your unit from freezing

temperatures.

• Failure to do so will permanently damage your pump

and render your unit inoperable.

• Freeze damage is not covered under warranty.

To use Pump Saver, make sure electric pressure washer

is turned off and inlet and outlet hoses are disconnected.

Read and follow all instructions and warnings given on the

Pump Saver container.

Final Storage Procedures

1. Wrap high pressure hose and power cord on hook.

2. Store spray gun, spray wand, and 7-in-1 nozzle in

provided storage areas. Store red high pressure

nozzle on end of spray wand.

3. Store unit in a clean, dry area that is protected from

freezing temperatures. The unit is equipped with a

foldable handle. The handle can be folded down

for storage. The unit can be operated in vertical or

horizontal positions.

4. Cover unit with a suitable protective cover that does

not retain moisture.

14 BRIGGSandSTRATTON.COM

Troubleshooting

Problem Cause Correction

Pump has following problems:

failure to produce pressure,

erratic pressure, chattering,

loss of pressure, low water

volume.

1. Water inlet is blocked.

2. Inadequate water supply.

3. Garden hose is kinked or leaking.

4. Clogged water inlet screen.

5. Water supply is over 100°F

(38°C).

6. High pressure hose is blocked or

leaks.

7. Nozzle is obstructed.

1. Clear inlet.

2. Provide adequate water flow.

3. Straighten garden hose or replace if

leaking.

4. Check and clean water inlet screen.

5. Provide cooler water supply.

6. Clear blocks in high pressure hose or

replace hose.

7. Clean spray tip.

Unit fails to start when spray

gun trigger is squeezed.

1. Water supply is not turned on.

2. Unit is not turned on.

3. Garden hose is too long.

4. Fuse blown or circuit breaker

tripped.

1. Turn on water supply.

2. Turn master ON/OFF switch to ON (I)

position. Reset GFCI.

3. Use only 50 ft. (15.24 m) maximum

garden hose.

4. a.) Check fuse box for blown fuse and

replace as necessary or reset circuit

breaker. Do not use a fuse or circuit

breaker with a higher rating than that

specified for your particular branch

circuit.

b.) Disconnect other electrical

appliances and turn off lights in the

circuit or operate the pressure washer

on its own dedicated circuit.

c.) Run pressure washer in any

POWERflow+ High Flow nozzle

setting for 10 minutes. Motor break in

may be necessary.

Detergent fails to mix with

spray.

1. High pressure or high flow without

soap nozzle is selected.

2. Inlet water supply pressure too

high.

1. Select a high flow soap nozzle setting

(indicated with bubbles).

2. Slowly close water supply valve until

chemical just starts to draw (soap suds

will appear when chemical starts to

draw).

Hose connections leaking.

1. Garden hose loose to water inlet.

2. Loose high pressure hose

connections.

3. Damaged o-ring.

1. Hand tighten garden hose to water

inlet.

2. Remove hose completely and reinstall

hand tight.

3. Replace o-ring.

For all other issues, see a Briggs & Stratton authorized dealer.

Specifications

Max Outlet Pressure ................2,000 PSI (138 BAR)* @ 1.1 GPM (4.1 liters/min)

Max Flow Rate ..................... 3.5 GPM* (13.25 liters/min)* @ 80 PSI (5.5 BAR)

Detergent Mix ...........................................See MFR’s Instructions

Water Supply Temperature ............................ Not to exceed 100°F (38°C)

Motor ......................................................... Induction Type

Rated Voltage ....................................................120 Volts AC

Current............................................................13.0 Amps

*This pressure washer is rated in accordance to the Pressure Washer Manufacturers’ Association

(PWMA) standard PW101-2018 (Testing and Rating Performance of Pressure Washers).

16 BRIGGSandSTRATTON.COM

80018419_EN Rev A

BRIGGS & STRATTON WARRANTY POLICY

LIMITED WARRANTY

Briggs & Stratton warrants that, during the warranty period specified below, it will repair or replace, free of charge, any part that is defective in material or workmanship or

both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective for and is subject

to the time periods and conditions stated below. For warranty service, contact Briggs & Stratton Customer Service by phone at (800) 743-4115, or on the internet at

BRIGGSANDSTRATTON.COM.

There is no other express warranty. Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to the warranty

period listed below, or to the extent permitted by law. Liability for incidental or consequential damages are excluded to the extent exclusion is permitted

by law. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion or limitation of

incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other

rights which vary from state to state or country to country.**

WARRANTY PERIOD

** In Australia - Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major

failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be

of acceptable quality and the failure does not amount to a major failure. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at

BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by emailing or writing to [email protected], Briggs & Stratton Australia Pty Ltd, 1

Moorebank Avenue, NSW, Australia, 2170.

The warranty period begins on the date of purchase by the first retail or commercial consumer. “Consumer use” means personal residential household use by a retail

consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes. Once a product has experienced commercial use, it

shall thereafter be considered as a commercial use product for purposes of this warranty.

Save your proof of purchase receipt. If you do not provide proof of the initial purchase date at the time warranty service is requested, the manufacturing date of the product will

be used to determine the warranty period. Product registration is not required to obtain warranty service on Briggs & Stratton products.

ABOUT YOUR WARRANTY

Most warranty repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. This warranty covers only defects in materials or

workmanship. It does not cover damage caused by improper use or abuse, improper maintenance or repair, normal wear and tear, or stale or unapproved fuel.

Improper Use and Abuse - The proper, intended use of this product is described in the Operator’s Manual. Using the product in a way not described in the Operator’s Manual

or using the product after it has been damaged will not be covered under this warranty. Warranty coverage will also not be provided if the serial number on the product has

been removed or the product has been altered or modified in any way, or if the product has evidence of abuse such as impact damage or water/chemical corrosion damage.

Improper Maintenance or Repair - This product must be maintained according to the procedures and schedules provided in the Operator’s Manual, and serviced or repaired

using genuine Briggs & Stratton parts or equivalent. Damage caused by lack of maintenance or use of non-original parts is not covered by warranty.

Normal Wear and Tear - Like most mechanical devices, your unit is subject to wear even when properly maintained. This warranty does not cover repairs when normal

use has exhausted the life of a part or the equipment. Maintenance and wear items such as filters, belts, cutting blades, and brake pads (except engine brake pads) are not

covered by warranty due to wear characteristics alone, unless the cause is due to defects in material or workmanship.

Stale or Unapproved Fuel - In order to function correctly, this product requires fresh fuel that conforms to the criteria specified in the Operator’s Manual. Engine or equipment

damage caused by stale fuel or the use of unapproved fuels (such as E15 or E85 ethanol blends) is not covered by warranty.

Other Exclusions - This warranty excludes damage due to accident, abuse, modifications, alterations, improper servicing, freezing or chemical deterioration. Attachments or

accessories that were not originally packaged with the product are also excluded. There is no warranty coverage on equipment used for primary power in place of utility power

or on equipment used in life support applications. This warranty does not include used, reconditioned, second-hand, or demonstration equipment or engines. This warranty

also excludes failures due to acts of God and other force majeure events beyond the manufacturer’s control.

Consumer Use Commercial Use

12 months None

Número de modelo __________________________

Revisión __________________________________

Número de serie ____________________________

Fecha de compra ___________________________

Milwaukee, WI, USA. Reservados todos los derechos.

(800) 743-4115

BRIGGSandSTRATTON.COM

Hidrolavadora eléctrica

Manual del operador

2 BRIGGSandSTRATTON.COM

Gracias por comprar esta hidrolavadora eléctrica Briggs & Stratton® de alta calidad. Nos complace que haya depositado

su confianza en la marca Briggs & Stratton. Si la operación y el mantenimiento de su producto Briggs & Stratton se realiza

según las instrucciones de este manual, le proporcionará muchos años de servicio confiable.

Este manual contiene información de seguridad para alertarlo sobre los peligros y riesgos asociados con las

hidrolavadoras eléctricas, y para indicarle cómo evitarlos. Dado que Briggs & Stratton no conoce necesariamente todas

las aplicaciones para las cuales se podría utilizar esta hidrolavadora eléctrica, es importante que usted lea detalladamente

y entienda estas instrucciones antes de hacer arrancar o utilizar este equipo. Guarde estas instrucciones originales

para futuras consultas.

Esta hidrolavadora eléctrica requiere su montaje final antes de su uso. Consulte la sección Montaje de este manual

para conocer las instrucciones sobre los procedimientos de montaje final. Siga las instrucciones detalladamente.

Contacto

Nunca debe ir demasiado lejos para encontrar el soporte y el servicio de Briggs & Stratton para su hidrolavadora eléctrica.

Existen muchos distribuidores de servicio autorizado por Briggs & Stratton en todo el mundo, quienes suministran servicio

de calidad. También puede ponerse en contacto con Atención al Cliente de Briggs & Stratton por teléfono al (800) 743-

4115 o en Internet en BRIGGSandSTRATTON.COM.

Registrar su producto

Para asegurar pronta y completa cobertura de la garantía, registre su producto en línea en

www.onlineproductregistration.com.

Índice

Seguridad del operador . . . . . . . . . . . . . . . . . . . . . . . 3

Montaje .................................... 6

Características y controles..................... 9

Operación .................................. 9

Mantenimiento .............................12

Almacenamiento............................13

Solución de problemas.......................14

Especificaciones............................15

Garantía...................................16

Seguridad del operador

Descripción del equipo

Se ha realizado el máximo esfuerzo para reunir en este

manual la información más precisa y actualizada. No

obstante, nos reservamos el derecho de modificar, alterar

o mejorar de cualquier otra forma el producto y este

documento en cualquier momento y sin previo aviso.

Este sistema de encendido por chispa cumple con la

norma canadiense CAN ICES-2/NMB-2.

POWERflow+™ Technology

Un giro fácil. 7 formas de limpiar.

POWERflow+ Technology es una limpiadora a presión

de limpieza profunda con alta presión para despegar la

suciedad Y alto flujo para enjuagar. En el modo de alto

flujo, POWERflow+ Technology mejora la experiencia de

limpieza ofreciendo un alcance extendido, un poderoso

enjabonado y una capacidad más rápida de enjuague.

La fuerza detrás de PowerFlow+ se encuentra en la bomba

con dos modos de limpieza separados: alta presión y alto

flujo. Estos dos modos pueden intercambiarse fácilmente

gracias a la boquilla con diseño 7-en-1, que evita cambiar

las boquillas. El modo de alta presión ofrece hasta 2000 PSI

(libras por pulgada cuadrada), y es perfecto para la limpieza

de manchas resistentes, moho y mugre de plataformas,

entradas de vehículos y recubrimientos. El modo de alto

flujo ofrece hasta 3.5 GPM (galones por minuto) para

enjuagar con fuerza suciedad, jabón y desechos. El

modo de alto flujo también es excelente para el lavado de

superficies delicadas, como muebles de jardín, vehículos, y

juegos y juguetes de exterior para niños.

Protección mediante el interruptor de circuito por

fallos con conexión a tierra

Esta hidrolavadora está cuenta con un interruptor de

circuito por fallos con conexión a tierra (GFCI, ground-fault

circuit-interrupter) montado en el enchufe del cable de

alimentación. Este dispositivo proporciona una protección

adicional contra el riesgo de descarga eléctrica. En

caso de que sea necesario reemplazar el enchufe o el

cable, utilice solamente piezas de repuesto idénticas que

incluyan la protección de GFCI.

Apagado automático

La hidrolavadora eléctrica está equipada con un sensor

que detecta que el flujo de agua se ha detenido al liberar o

bloquear el gatillo de la pistola de pulverización. El sensor

hará que el motor se apague durante el tiempo que el gatillo

de la pistola de pulverización esté liberado o bloqueado.

Si el motor sigue funcionando cuando el gatillo de la pistola

de pulverización está liberado o bloqueado, NO UTILICE

LA MÁQUINA. Llame a la línea directa para hidrolavadoras

eléctricas al (800) 743-4115 para obtener ayuda.

AVISO La hidrolavadora eléctrica está equipada con un

interruptor principal de encendido/apagado. El interruptor

siempre debe moverse a la posición de apagado (0)

cuando la hidrolavadora eléctrica no se está usando para

evitar posibles daños.

Sobrecarga del motor

El motor eléctrico de esta hidrolavadora eléctrica está

equipado con un dispositivo de protección de sobrecarga

(termostato). Este dispositivo apagará automáticamente

el motor si este se sobrecalienta o en caso de exceso de

corriente.

Si se activa el dispositivo de protección de sobrecarga,

desconecte la fuente de alimentación moviendo el

interruptor principal de encendido/apagado a la posición

de apagado (0). Deje que la unidad se enfríe durante 30

minutos. A continuación, mueva el interruptor principal de

encendido/apagado a la posición de encendido (I) para

reanudar el funcionamiento.

Información importante de seguridad

Lea y comprenda todo el manual antes del montaje, la

operación o el mantenimiento del producto. Siga las

instrucciones de mantenimiento especificadas en este

manual. Si tiene alguna pregunta relacionada con el

producto, llame a Atención al Cliente al (800) 743-4115,

de lunes a viernes, de 8 a. m. a 5 p. m., CST.

Símbolos de seguridad y significados

El símbolo de alerta de seguridad indica un posible

riesgo para su integridad física. Se utiliza una palabra de

señalización (PELIGRO, ADVERTENCIA o PRECAUCIÓN)

junto con el símbolo de alerta para designar un grado o

nivel de gravedad de riesgo. Se puede utilizar un símbolo

de seguridad para representar el tipo de riesgo. AVISO

indica una información considerada importante, pero no

relacionada con un peligro potencial.

PELIGRO indica un peligro que, si no se evita,

ocasionará la muerte o lesiones graves.

ADVERTENCIA indica un peligro que, si no se evita,

podría ocasionar la muerte o lesiones graves.

PRECAUCIÓN indica un peligro que, si no se evita,

podría ocasionar lesiones menores o moderadas.

AVISO indica una información considerada importante, pero

no relacionada con un peligro potencial.

ADVERTENCIA No leer ni seguir las instrucciones del

manual del operador y todas las instrucciones de

funcionamiento antes de usar la unidad podría

ocasionar la muerte o lesiones graves.

• Lea este manual cuidadosamente y familiarícese con la

hidrolavadora eléctrica. Conozca sus aplicaciones, sus

limitaciones y los peligros involucrados.

Quemadura

química

Descarga eléctrica

Superficie

resbaladiza

Caídas

Objetos

voladores

Lea el manual

Proyectil

Inyección

de fluidos

Fuego

4 BRIGGSandSTRATTON.COM

ADVERTENCIA El uso de la hidrolavadora eléctrica

podría formar charcos y generar

superficies resbaladizas.

Riesgo de contragolpe. La pistola de

pulverización podría causar un contragolpe, con riesgo de

caída que podría provocar la muerte o lesiones graves.

• Opere la hidrolavadora eléctrica desde una superficie

estable.

• No se estire ni se pare sobre un apoyo inestable.

Mantenga una postura firme y un buen equilibrio en

todo momento.

• La zona de limpieza debe tener inclinaciones

adecuadas y sistema de drenaje para reducir la

posibilidad de caída debido a superficies resbaladizas.

• Sea extremadamente cuidadoso si debe usar la

hidrolavadora eléctrica desde una escalera, un

andamio u otro lugar similar.

• Sujete firmemente la pistola de pulverización con

ambas manos al utilizar modos de pulverización

eléctrica para evitar lesiones en caso de contragolpe de

la pistola.

ADVERTENCIA El chorro de agua a alta presión que

este equipo produce podría atravesar la piel y

los tejidos subcutáneos, y provocar lesiones

graves y posible amputación.

La pistola de pulverización acumula agua a alta

presión, incluso con el motor detenido y el agua

desconectada, lo que puede provocar lesiones graves.

• NUNCA apunte la pistola de pulverización hacia

personas, animales o plantas.

• SIEMPRE apunte con la pistola de pulverización hacia

una dirección segura y apriete el gatillo de la pistola

para liberar la alta presión, cada vez que apague la

hidrolavadora.

ADVERTENCIA Riesgo de lesiones oculares o

corporales. La pulverización podría

salpicar, propulsar objetos o causar

daños internos, lo que puede provocar

lesiones graves.

• Siempre use gafas de seguridad con ventilación indirecta

(salpicaduras de productos químicos) identificadas en

cumplimiento de la norma ANSI Z87.1 cuando utilice

este equipo o esté cerca de él. NUNCA sustituya las

gafas de seguridad con ventilación indirecta con gafas de

seguridad o gafas de condición seca.

• Sepa cómo detener la hidrolavadora y descargar la

presión rápidamente. Familiarícese completamente con

los controles.

• NO permita que ningún NIÑO opere la hidrolavadora

eléctrica.

• Mantenga el área de operación libre de personas.

• Inspeccione la manguera de alta presión antes de

cada uso. NUNCA repare la manguera de alta presión;

reemplácela.

• NO repare las conexiones con fugas con sellador de

ningún tipo; reemplace las juntas tóricas y juntas.

• Mantenga la manguera conectada a la hidrolavadora

eléctrica y a la pistola de pulverización cuando el

sistema esté presurizado.

• SIEMPRE apunte con la pistola de pulverización

hacia una dirección segura mientras el sistema esté

presurizado y apriete el gatillo de la pistola para liberar

la alta presión, cada vez que apague la hidrolavadora.

• NO apunte la pistola de pulverización hacia personas o

animales.

• NO beba de los accesorios conectados a la manguera.

• NO fije la pistola de pulverización en la posición abierta.

• NO deje la pistola de pulverización desatendida

cuando la hidrolavadora eléctrica está en la posición de

encendido (I).

• NO utilice una pistola de pulverización que no tenga

un bloqueo o seguro de gatillo instalado y en buenas

condiciones.

• Asegúrese siempre de que la pistola de pulverización y

los accesorios estén conectados correctamente.

• Manténgase alerta, observe lo que está haciendo.

• NO haga funcionar el producto si está cansado o bajo

la influencia de alcohol o drogas.

• Se requiere supervisión minuciosa cuando este

producto se utiliza cerca de niños.

ADVERTENCIA Riesgo de electrocución. El uso

de un cable de prolongación podría ocasionar

descarga eléctrica o quemaduras que pueden

provocar lesiones graves o la muerte.

• NO use un cable de prolongación con esta

hidrolavadora eléctrica. Es posible que el cable de

prolongación o el enchufe del circuito eléctrico de su

casa no proporcione la protección del interruptor de

circuito por fallos con conexión a tierra que resguarda

la vida de las personas.

ADVERTENCIA Riesgo de electrocución. Poner en

contacto al mismo tiempo ambos conductores

de energía podría provocar una descarga

eléctrica o incendio que causen muertes o

lesiones graves.

• Conectarla solo a un toma corriente con una buena

descarga a tierra. NO quite el terminal de tierra del enchufe.

• Compruebe que el cable esté en buenas condiciones antes

de usar la unidad. NO la utilice si el cable está dañado.

• El producto cuenta con un interruptor del circuito de fallo a

tierra (GFCI) que se encuentra en el cable del enchufe. Si es

necesario reemplazar el enchufe o el cable, reemplácelos

exclusivamente por piezas de repuesto idénticas.

• Mantenga todas las conexiones secas y lejos del suelo.

• NO toque el enchufe con las manos mojadas.

• NO pase el cable por entradas, ventanas, orificios en

los techos, paredes o pisos.

• NO pise el cable.

• NO aplaste, arrastre o coloque objetos sobre el cable.

• NO moje el área cercana a la fuente de energía.

La page est en cours de chargement...

Simplicity 020667V-00 Manuel utilisateur

Marque: Simplicity

Modèle: 020667V-00

Catégorie: Nettoyeurs haute pression

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Simplicity 020667V-00 User manual
español: Simplicity 020667V-00 Manual de usuario

Simplicity 020667V-00 Manuel utilisateur

Simplicity 020667V-00 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents