Simplicity WALKBEHIND MOWER, SNAPPER, FC MODELS S(P)19550EX Manuel utilisateur

Marque: Simplicity

Modèle: WALKBEHIND MOWER, SNAPPER, FC MODELS S(P)19550EX

Catégorie: Tondeuses à gazon

Taper: Manuel utilisateur

Ce manuel convient également à

881545-00

Original Instruction

Form No. 881631

Revision: -

English Operator’s Manual

en fr

Français Manuel d'utilisation

Not for

Reproduction

2 BriggsandStratton.com

Not for

Reproduction

12 13

C F

Not for

Reproduction

4 BriggsandStratton.com

15 16

Not for

Reproduction

Not for

Reproduction

6 BriggsandStratton.com

41 42

Not for

Reproduction

7105261

AVERTISSEMENT

WARNING

POUR ÉVITER DES BLESSURES GRAVES VOIRE MORTELLES

• Lire le manuel d’utilisation.

• Maintenir en place et en état de marche les dispositifs

de sécurité (protections, écrans, commutateurs, etc.)

• Enlever les objets quipeuvent être projetés par la lame.

• Passer latéralement sur les pentes,pas en montant

ou descendant.

• Eviter les pentes raides.

• Ne pastondre s’il y a des enfantsoudes badauds

aux alentours.

• Regarder en bas et derrière avant et pendantune

marche arrière.

• Patienter au moins 2 minutes avant de refaire le plein.

• Cette machine peut créer des étincelles pouvant

provoquer l’incendie de la végétation sèche. Un

pare-étincelles peut être nécessaire. Contacter les

organismes d’incendie locaux pour les réglemen-

tations relatives aux exigences de prévention d’incendie.

• Read operator’s manual.

• Keep safety devices (guards, shields, switches,

etc.) in place and working.

• Remove objects that could be thrown by blade.

• Go across slopes, not up and down.

• Avoid steep slopes.

• Do not mow when children or others are around.

• Look down and behind before and while moving

backwards.

• Wait at least 2 minutes before refueling.

• This equipment may create sparks that can start

fires around dry vegetation. Spark arrestor may

be required. Contact local fire agencies for

regulations relating to fire prevention requirements.

This spark ignition system complies with

Canadian standard ICES-002

Ce système d'allumage par étincelle de véhicule est conforme

à la norme NMB-002 du Canada.

AVOID SERIOUS INJURY OR DEATH

7105217

DANGERDANGER

RISQUE D’AMPUTATION ET OBJETS PROJETÉS

• Garder mains et pieds à l’écartde la plate-forme

de coupe.

• Ne pasutiliser la tondeuse si le déversoiroutout le

bac à herbepas bien en place.

AMPUTATION AND THROWN OBJECT HAZARD

• Keep hands and feet away from deck.

• Do not operate mower unless discharge deflector

or entire grass catcher is in its proper place.

F G

B C D

K L M

N PO

Not for

Reproduction

8 BriggsandStratton.com

Thank You for purchasing this quality-built product. We’re pleased that you placed your

conﬁdence in our brand. When operated and maintained according to the instructions in this

manual, your product will provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated

with the machine and how to avoid them. This machine is designed and intended only for ﬁnish

cutting of established lawns and is not intended for any other purpose. It is important that you

read and understand these instructions thoroughly before attempting to start or operate this

equipment. Save these original instructions for future reference.

Complete the following information on your purchase.

Date of Purchase____________________________________________________________

Retailer___________________________________________________________________

Retailer’s Phone Number______________________________________________________

Equipment

Model Number_________________________________________________________

Serial Number_________________________________________________________

Engine

Model_________________Type________________Code_______________________

Power Rating

The gross power rating for individual gas engine models is labeled in accordance with SAE (So-

ciety of Automotive Engineers) code J1940 (Small Engine Power & Torque Rating Procedure),

and rating performance has been obtained and corrected in accordance with SAE J1995 (Revi-

sion 2002-05). Torque values are derived at 3060 RPM; horsepower values are derived at 3600

RPM. The gross power curves can be viewed at www.BRIGGSandSTRATTON.COM. Net power

values are taken with exhaust and air cleaner installed whereas gross power values are collected

without these attachments. Actual gross engine power will be higher than net engine power and

is affected by, among other things, ambient operating conditions and engine-to-engine vari-

ability. Given the wide array of products on which engines are placed, the gas engine may not

develop the rated gross power when used in a given piece of power equipment. This difference

is due to a variety of factors including, but not limited to, the variety of engine components (air

cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient

operating conditions (temperature, humidity, altitude), and engine-to-engine variability. Due to

manufacturing and capacity limitations, Briggs & Stratton may substitute an engine of higher

rated power for this Series engine.

Contents

Illustrations ............................................................................................................................... 2

Operator Safety ........................................................................................................................... 8

Features and Controls ............................................................................................................... 10

Pictorals ............................................................................................................................. 10

Assembly ............................................................................................................................. 11

Operation ............................................................................................................................. 12

Maintenance ............................................................................................................................. 13

Troubleshooting ........................................................................................................................ 15

Speciﬁcations ............................................................................................................................ 15

Warranty Policy ......................................................................................................................... 16

Operator Safety

Symbols And Warnings

The safety alert symbol is used to identify safety information about hazards that can

result in personal injury. A signal word (DANGER, WARNING, or CAUTION) is used with the

alert symbol to indicate the likelihood and the potential severity of injury. In addition, a hazard

symbol may be used to represent the type of hazard.

DANGER indicates a hazard which, if not avoided, will result in death or

serious injury.

WARNING indicates a hazard which, if not avoided, could result in death or

serious injury.

CAUTION indicates a hazard which, if not avoided, could result in minor or

moderate injury.

NOTICE indicates a situation that could result in damage to the product.

WARNING:

Certain components in this product and its related accessories

contain chemicals known to the State of California to cause cancer, birth

defects, or other reproductive harm. Wash hands after handling.

WARNING: The engine exhaust from this product contains chemicals known

to the State of California to cause cancer, birth defects, or other reproductive

harm.

WARNING: It is a violation of California Public Resource Code, Section 4442,

to use or operate the engine on any forest-covered, brush-covered, or grass-

covered land unless the exhaust system is equipped with a spark arrester, as

defined in Section 4442, maintained in effective working order. Other states or

federal jurisdictions may have similar laws. Contact the original equipment manufacturer,

retailer, or dealer to obtain a spark arrester designed for the exhaust system installed on

this engine.

Responsibility Of The Owner

WARNING: This powerful cutting machine is capable of amputating hands and

feet and can throw objects that can cause injury and damage! Failure to comply

with the following SAFETY instructions could result in serious injury or death to

the operator or other persons.

The owner of the machine must understand these instructions and must allow only persons

who understand these instructions to operate machine. Each person operating the machine

must be of sound mind and body and must not be under the influence of any substance,

which might impair vision, dexterity or judgment. If you have any questions pertaining to your

machine which your dealer cannot answer to your satisfaction, contact Customer Service.

Operating Safety

Power equipment is only as safe as the operator. If it is misused, or not properly maintained,

it can be dangerous! Remember, you are responsible for your safety and that of those around

you.

Use common sense, and think through what you are doing. If you are not sure that the task you

are about to perform can be safely done with the equipment you have chosen, ask a profes-

sional: contact your local authorized dealer.

Read the Manual

The operator’s manual contains important safety information you need to be aware of BEFORE

you operate your unit as well as DURING operation.

Safe operating techniques, an explanation of the product’s features and controls, and mainte-

nance information is included to help you get the most out of your equipment investment.

Be sure to completely read the Safety Rules and Information found on the following pages. Also

completely read the Operation section.

Not for

Reproduction

Children

Tragic accidents can occur with children. Do not allow them anywhere near the area of opera-

tion. Children are often attracted to the unit and mowing activity. Never assume that children

will remain where you last saw them. If there is a risk that children may enter the area where

you are mowing, have another responsible adult watch them.

Slope Operation

20.0 ft

(6.0 m)

3.5 ft

(1.5 m)

You could be seriously injured or even killed if you use this unit on too steep an incline. Using

the unit on a slope that is too steep or where you don’t have adequate footing or traction can

cause you to lose control or slip and fall.

You should not operate on inclines with a slope greater than 10 degrees, which is a 3.5 ft (1,5

m) rise over 20.0 ft (6,0 m). Always mow across slopes, never up and down.

Also note that the surface you are mowing can greatly impact control. Wet grass or leaves can

seriously affect your footing and traction on a slope.

If you feel unsure about operating the unit on an incline, don’t do it. It’s not worth the risk.

Moving Parts

This equipment has moving parts that can injure you or someone else. However, if you stand

behind the handle properly and follow all the rules in this book, the unit is safe to operate.

The mower deck has a spinning mower blade that can amputate hands and feet. Do not allow

anyone near the equipment while it is running!

To help you, the operator, use this equipment safely, it is equipped with an operator present

safety system. Do NOT attempt to alter or bypass the system. See your dealer immediately if

the system does not pass all the safety interlock system tests found in this manual.

Thrown Objects

This unit has a spinning mower blade. This blade can pick up and throw debris that could seri-

ously injure a bystander. Be sure to clean up the area to be mowed BEFORE you start mowing.

Do not operate this unit without the entire grass catcher or discharge guard (deflector) in place.

Also, do not allow anyone in the area while the unit is running! If someone does enter the area,

shut the unit off immediately until they leave.

Debris Accumulation

Accumulation of grass and debris can result in a fire. Be sure to clean any accumulation of

grass and debris with a brush or compressed air, before and after operation.

Fuel and Maintenance

Gasoline is extremely flammable. Its vapors are also extremely flammable and can travel to

distant ignition sources. Gasoline must only be used as a fuel, not as a solvent or cleaner. It

should never be stored any place where its vapors can build up or travel to an ignition source

like a pilot light. Fuel belongs in an approved, plastic, sealed gas can, or in the tractor fuel tank

with the cap securely closed. Spilled fuel needs to be cleaned up immediately.

Proper maintenance is critical to the safety and performance of your unit. Be sure to perform

the maintenance procedures listed in this manual, especially periodically testing the safety

system.

Operator Safety Instructions

Protection for Children

Tragic accidents can occur if the operator is not alert to the presence of children. Children are

often attracted to the machine and the mowing activity. Never assume that children will remain

where you last saw them.

1. KEEP children out of the mowing area and under the watchful care of a responsible adult

other than the operator.

2. DO NOT allow children in yard when machine is operated and turn machine OFF if anyone

enters the area.

3. DO NOT allow pre-teenage children to operate machine.

4. ALLOW only responsible adults & teenagers with mature judgment under close adult

supervision to operate machine.

5. DO NOT pull mower backwards unless absolutely necessary. LOOK and SEE behind and

down for children, pets and hazards before and while backing.

6. USE EXTRA CARE when approaching blind corners, shrubs, trees, or other objects that

may obscure vision.

Slope Operation

1. Slopes are a major factor related to slip and fall accidents, which can result in severe

injury. All slopes require extra caution. If you feel uneasy on a slope, DO NOT mow it.

2. Mow across slopes, never up-and-down. Exercise extreme CAUTION when changing

directions on slopes. DO NOT mow steep slopes (maximum 10 degrees) or other areas

where stability or traction is in doubt.

3. Use extra care with grass catchers or other attachments; these affect the handling and

the stability of the machine.

Preparation

1. Read, understand, and follow instructions and warnings in this manual and on the

mower, engine and attachments. Know the controls and the proper use of the mower

before starting.

2. Only mature, responsible persons shall operate the machine and only after proper

instruction.

3. Data indicates that operators age 60 and above, are involved in a large percentage of

mower-related injuries. These operators should evaluate their ability to operate the

mower safely enough to protect themselves and others from serious injury.

4. Handle fuel with extra care. Fuels are flammable and vapors are explosive. Use only an

approved fuel container. DO NOT remove fuel cap or add fuel with engine running. Add

fuel outdoors only with engine stopped and cool. Clean spilled fuel and oil from machine.

DO NOT smoke.

5. Check the area to be mowed and remove all objects such as toys, wire, rocks, limbs and

other objects that could cause injury if thrown by blade or interfere with mowing. Also

note the location of holes, stumps, and other possible hazards.

6. Keep people and pets out of the mowing area. Immediately, STOP Blade, Stop engine and

Stop mower if anyone enters the area.

7. Check shields, deflectors, switches, blade controls and other safety devices frequently for

proper operation and location.

8. Make sure all safety decals are clearly legible. Replace if damaged.

Not for

Reproduction

10 BriggsandStratton.com

9. Protect yourself when mowing and wear safety glasses, a dust mask, long pants, and

substantial footwear. DO NOT mow barefooted or with sandals.

10. Know how to STOP blade and engine quickly in preparation for emergencies.

11. Use extra care when loading or unloading the machine into a trailer or truck.

12. Check grass catcher components frequently for signs of wear or deterioration and re-

place as needed to prevent injury from thrown objects going through weak or torn spots.

Safe Handling of Gasoline

To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is

extremely flammable and the vapors are explosive.

1. Extinguish all cigarettes, cigars, pipes and other sources of ignition.

2. Use only an approved fuel container.

3. DO NOT remove fuel cap or add fuel with the engine running. Allow the engine to cool

before refueling.

4. DO NOT refuel the machine indoors.

5. DO NOT store the machine or fuel container inside where there is an open flame, spark or

pilot light such as on a water heater or other appliances.

6. DO NOT ﬁll fuel containers inside a vehicle or on a truck or trailer bed with a plastic liner.

Always place the containers on the ground away from the vehicle before ﬁlling.

7. Remove gas-powered equipment from the vehicle or trailer and refuel it on the ground.

If this is not possible, then refuel equipment using a portable container, rather than a

gasoline dispenser nozzle.

8. DO NOT start gas powered equipment in enclosed vehicles or trailers.

9. Keep the nozzle in contact with the rim of the fuel tank or container opening at all times

until fueling is complete. DO NOT use a nozzle lock-open device

10. If fuel is spilled on clothing, change clothing immediately.

11. DO NOT overﬁll a fuel tank. Replace fuel cap and tighten securely.

Operation

1. DO NOT put hands or feet near or under rotating parts. Keep clear of discharge area

while engine is running.

2. STOP engine when crossing gravel drives, walks, or roads, and under any conditions

where thrown objects might be a hazard.

3. Mow only in daylight or good artiﬁcial light.

4. DO NOT operate mower while under the inﬂuence of alcohol or drugs.

5. After striking a foreign object or if mower vibrates abnormally, STOP the engine, discon-

nect and secure spark plug wire. Inspect the mower for any damage and repair the

damage before starting.

6. DO NOT mow near drop offs, ditches or embankments. Operator could lose footing or

balance.

7. STAY ALERT for holes and other hidden hazards. Tall grass can hide obstacles. Keep

away from ditches, washouts, culverts, fences and protruding objects.

8. DO NOT mow on wet grass. Always be sure of your footing. Keep a ﬁrm hold on the

handle and walk, never run. Slipping could cause injury.

9. ALWAYS stay behind handle when engine (motor) is running.

10. DO NOT leave the machine with the engine running. STOP BLADE and STOP ENGINE

before leaving the operator’s position for any reason.

11. Before cleaning, repairing or inspecting make certain engine, blade and all moving parts

have STOPPED. Disconnect and secure spark plug wire away from plug to prevent ac-

cidental starting.

12. STOP engine and wait until the blade comes to complete STOP before removing grass

bag and/or clearing grass.

13. DO NOT operate mower without the entire grass catcher, or guards in place discharge

guard, rear guard or other safety devices in place and working. DO NOT point discharge

at people, passing cars, windows or doors.

14. DO NOT discharge material against a wall or obstruction. Material may ricochet back

towards the operator.

15. Slow down before turning.

16. Watch out for trafﬁc when near or crossing roadways.

17. DO NOT operate engine in enclosed areas. Engine exhaust gases contain carbon monox-

ide, a deadly poison.

18. Only use accessories approved by the manufacturer. See manufacturer’s instructions for

proper operation and installation of accessories.

Maintenance and Storage

1. DO NOT store mower or fuel container inside where fumes may reach an open ﬂame,

spark or pilot light such as in a water heater, furnace, clothes dryer or other gas appli-

ance. Allow engine to cool before storing machine in an enclosure. Store fuel container

out of reach of children in a well ventilated, unoccupied building.

2. Keep mower and engine free of grass, leaves or excess grease to reduce ﬁre hazard and

engine overheating.

3. When draining fuel tank, drain fuel into an approved container outdoors and away from

open ﬂame.

4. Keep all bolts, especially blade bolts, nuts and screws properly tight. Check that all cotter

pins are in proper position.

5. Always provide adequate ventilation when running engine. Engine exhaust gases contain

carbon monoxide, a deadly poison.

6. Service engine and make adjustments only when engine is stopped. Removed spark plug

wire from spark plug and secure wire away from spark plug to prevent accidental start-

ing.

7. DO NOT change engine governor speed settings or overspeed engine.

8. Check grass bag assembly frequently for wear or deterioration to avoid thrown objects

and exposure to moving parts. Replace with new bag if loose seams or tears are evident.

Replace slider or bag adapter if broken or cracked.

9. Mower blades are sharp and can cut. Wrap the blades or wear heavy leather gloves and

use CAUTION when handling them.

10. DO NOT test for spark by grounding spark plug next to spark plug hole; spark plug could

ignite gas exiting engine.

11. Have machine serviced by an authorized dealer at least once a year and have the dealer

install any new safety devices.

12. Use only factory authorized replacement parts or like

parts when making repairs.

Intended Use/Limits Of Use

The walk-behind lawn mower is designed to cut lawn grass. Any other use is not permitted. It is

not designed to cut grass over 15cm in length or grass mixed with tall weeds. The lawn mower

is only suitable for private use in a domestic garden. It is not suitable for cutting grass in public

parks or playing ﬁelds.

Features and Controls

NOTICE: The ﬁgures, illustations and pictorials in this manual are for reference only, and may

differ from your speciﬁc model.

Compare the following features and controls with your model (Figure 1). Make sure that you

know the location and understand their purpose.

A. Engine Stop Lever

B. Upper Handle

C. Knob or Locking Lever

D. Lower Handle

E. Rear Door

F. Engine

G. Height Adjuster

H. Nameplate

I. Grass Bag

J. Recoil Starter Handle

K. Drive Lever (Self-propelled model)

L. Mulcher Plug

M. Side Discharge Chute

N. Mulch Cover

O. Engine Throttle Control (optional)

Pictorials

Important: The following pictorials are located on your unit or on literature supplied with the

product. Before you operate the unit, learn and understand the purpose for each pictorial.

Safety Warning Pictorials and Decals - Figure

A. WARNING

B. IMPORTANT: Read Owner’s Manual Before Operating This Machine.

C. WARNING: Thrown Objects. Keep Bystanders Away. Read User Instructions Before

Operating This Machine.

D. WARNING: Do Not Use This Machine On Slopes Greater Than 10 Degrees.

E. WARNING: No Step

F. WARNING: Keep Feet And Hands Away From Rotating Blade.

G. WARNING: Disconnect Spark Plug Wire Before Servicing Unit.

H. WARNING: Crushed Fingers.

I. WARNING: Keep Hands And Feet Away.

J. WARNING And DANGER Instructions.

Control And Operating Pictorials - Figure

K. Slow

L. Fast

M. Oil

N. Fuel

O. Engine/Blade -- Start/Run/Stop

P. Drive Control Lever - Engaged/Disengaged

Not for

Reproduction

Assembly

Illustrations and pictorials begin on page 2.

Unpacking Instructions - Figure

The mower was fully assembled at the factory. When the mower was put in the carton, the

handle was put in the storage position. To put the handle in the operating position, follow the

steps below.

1. Remove the mower from the carton.

2. Raise the lower handle (A) to the operating position (Figure 2).

3. The handle bracket (B) has two mounting holes (Figure 3). Use hole (C) to mount the

handle in the high position. Use hole (D) to mount the handle in the low position.

4. Mount the handle in either hole (C) or hole (D) with the fasteners as shown. Tighten

knobs (E) until the lower handle is secure.

5. Loosen the knobs (F) and fasteners securing the upper handle (G) to the lower handle

(A). See Figure 4. Put the upper handle (G) in the operating position. Tighten the knobs

(F) until the upper handle and lower handle are locked in place.

6. To mount the recoil starter rope, you must ﬁrst engage the engine stop lever (H). See

Figure 5. Slowly pull the recoil starter handle (I) and install the recoil starter rope into the

rope guide (J).

7. On all models, secure the cable to the handle with the wire tie (K). See Figure 6.

NOTICE: Be careful when you fold or raise the handle. Do not damage the cables. A cable

that is bent will not work correctly. Before you use the unit, replace a bent or damaged

cable.

How To Assemble The Handle Console (optional) - Figure

1. Remove the four panel fasteners (A) from the parts bag. See Figure 7.

2. Align the handle console (B) to the four mounting holes in the upper handle (C).

3. Attach the handle console (B) to the upper handle (C) with the four panel fasteners (A).

See Figure 8.

How To Assemble The Throttle Control (optional) - Figure

1. Remove the two small screws (D) from the parts bag. See Figure 9.

2. Align the holes in the throttle control (E) with the mounting holes in the handle

console (B).

3. Fasten the throttle control to the handle console with the two pan head screws.

4. Remove the throttle control knob from the parts bag.

5. Use a small hammer (F) and lightly tap the throttle control knob (G) onto the throttle

control arm. See Figure 10.

How To Assemble The Grass Bag - Figure

1. Slide the frame assembly (A) into the open end of the grass bag (B). See Figure 11.

2. Make sure the handle (C) is on the outside of the grass bag (Figure 12). Attach the clips

(D) to the frame assembly (E).

How To Mount The Grass Bag - Figure

1. Raise the rear door (F). See Figure 13. Hold the handle (G) of the grass bag and mount

the grass bag hooks (H) onto the rear door pivot rod (I).

2. Lower the rear door. Make sure the grass bag hooks (H) are mounted on the rear door

pivot rod (I).

How To Change The Mulcher Plug - Figure

WARNING: Before you remove or install the mulcher plug, disconnect the spark

plug wire and keep it away from the spark plug.

Some models have an optional mulcher plug (A). See Figure 14. Use the mulcher plug to mulch

the grass for a clean, ﬁne cut. To discharge the grass into the grass bagger, remove the mulcher

plug.

How To Install The Mulcher Plug

1. Raise the rear door (B). See Figure 14.

2. Slide the mulcher plug (A) into the discharge opening.

How To Remove The Mulcher Plug

1. Raise the rear door (B). See Figure 14.

2. Remove the mulcher plug (A) from the discharge opening.

How To Assemble The Side Discharge Chute - Figure

WARNING: Before you remove or install the side discharge chute, disconnect

the spark plug wire and keep it away from the spark plug.

1. Raise the mulch cover (A). See Figure 15.

2. Slide the two tabs (B) on the side discharge chute (C) under the pivot rod (D).

3. Lower the mulch cover (A). See Figure 16.

How To Prepare The Engine - Figure

NOTICE: The engine does not contain oil. Before you start the engine, make sure you add oil ac-

cording to the instructions in this manual. If you start the engine without oil, it will be damaged

beyond repair and will not be covered under warranty.

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty Certiﬁed oils for best performance. Other

high-quality detergent oils are acceptable if classiﬁed for service SF, SG, SH, SJ or higher. Do

not use special additives.

Outdoor temperatures determine the proper oil viscosity for the engine. Use the chart to select

the best viscosity for the outdoor temperature range expected.

* Below 40°F (4°C) the use of SAE 30 will result in hard starting.

** Above 80°F (27°C) the use of 10W-30 may cause increased oil consumption. Check oil level

more frequently.

How To Check/Add Oil

Before adding or checking the oil

• Place engine level.

• Clean the oil ll area of any debris.

1. Remove the dipstick (A) and wipe with a clean cloth (Figure 17, 18).

2. Insert and tighten the dipstick.

3. Remove the dipstick and check the oil level. It should be at the top of the full indicator

(B) on the dipstick.

4. If low, add oil slowly into the engine oil ﬁll (C). Do not overﬁll. After adding oil, wait one

minute and then recheck the oil level.

5. Replace and tighten the dipstick.

Fuel Recommendations

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). High altitude use, see below.

• Gasoline with up to 10% ethanol (gasohol) or up to 15% MTBE (methyl tertiary butyl

ether) is acceptable.

CAUTION: Do not use unapproved gasolines, such as E85. Do not mix oil in gasoline or modify

the engine to run on alternate fuels. This will damage the engine components and void the

engine warranty.

To protect the fuel system from gum formation, mix a fuel stabilizer into the fuel. See Storage.

All fuel is not the same. If starting or performance problems occur, change fuel providers or

change brands. This engine is certiﬁed to operate on gasoline. The emissions control system

for this engine is EM (Engine Modiﬁcations).

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum 85 octane/85 AKI (89 RON) gasoline

is acceptable. To remain emissions compliant, high altitude adjustment is required. Operation

without this adjustment will cause decreased performance, increased fuel consumption, and

increased emissions. See a Briggs & Stratton Authorized Dealer for high altitude adjustment

information.

Operation of the engine at altitudes below 2,500 feet (762 meters) with the high altitude kit is

not recommended.

Not for

Reproduction

12 BriggsandStratton.com

How To Add Fuel

WARNING

Fuel and its vapors are extremely ﬂammable and explosive.

Fire or explosion can cause severe burns or death.

When Adding Fuel:

• Turn engine off and let engine cool at least 2 minutes before removing the fuel cap.

• Fill fuel tank outdoors or in well-ventilated area.

• Do not overll fuel tank. To allow for expansion of the fuel, do not ll above the bot-

tom of the fuel tank neck.

• Keep fuel away from sparks, open ames, pilot lights, heat, and other ignition

sources.

• Check fuel lines, tank, cap, and ttings frequently for cracks or leaks. Replace if

necessary.

• If fuel spills, wait until it evaporates before starting engine.

1. Clean the fuel cap area of dirt and debris. Remove the fuel cap (A, Figure 19, 20, 21).

2. Fill the fuel tank (B) with fuel. To allow for expansion of the fuel, do not ﬁll above the

bottom of the fuel tank neck (C).

3. Reinstall the fuel cap.

Operation

Illustrations and pictorials begin on page 2.

Engine Stop Lever - Figure

Release the engine stop lever (A) and the engine and the blade will automatically stop. To start

and run the engine, hold the engine stop lever (A) in the operating position (B).

Before you start the engine, operate the engine stop lever several times. Make sure that the

engine stop cable moves freely and that the engine stop lever operates correctly.

How To Stop The Engine - Figure

To stop the engine, release the engine stop lever (A). Disconnect the wire and keep it away from

the spark plug to keep the engine from starting.

Rear Wheel Drive System - Figure

WARNING: For safe operation, the drive system must immediately disengage

when the drive lever is released. If the drive system does not disengage cor-

rectly, do not operate the mower until the drive system is adjusted or repaired

by an authorized service center.

Self-propelled models have a rear wheel drive system. Operate the drive system as follows.

1. Hold the engine stop lever (A) in the operating position (Figure 24, 25). Start the engine.

Note: To stop the engine, release the engine stop lever (A).

2. Hold the drive lever (C) against the handle (B). The drive system is now engaged and the

mower will move forward. To slow the speed, slightly release the drive lever.

3. To disengage only the drive system, release the drive lever (C). In the disengaged posi-

tion (D), the mower will stop moving forward but the engine will continue to run.

4. To disengage both the drive system and also to stop the engine, completely release the

engine stop lever (A).

Note: When the drive system is disengaged on a new unit, it is possible for the rear wheels to

rotate if lifted off the ground. This is normal with a new belt and will stop after one or two

hours of operation.

How To Start The Engine - Figure

WARNING: The blade will rotate when the engine runs.

WARNING

Rapid retraction of starter cord (kickback) will pull hand and arm toward engine

faster than you can let go.

Broken bones, fractures, bruises or sprains could result.

• When starting engine, pull the starter cord slowly until resistance is felt and then pull

rapidly to avoid kickback.

WARNING

Fuel and its vapors are extremely ﬂammable and explosive.

Fire or explosion can cause severe burns or death.

When Starting Engine

• Ensure that spark plug, mufer, fuel cap and air cleaner (if equipped) are in place and

secured.

• Do not crank engine with spark plug removed.

• If engine oods, set choke (if equipped) to OPEN/RUN position, move throttle (if

equipped) to FAST position and crank until engine starts.

WARNING

Engines give off carbon monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide can cause nausea, fainting or death.

• Start and run engine outdoors.

• Do not start or run engine in enclosed area, even if doors or windows are open.

Important: Before you start the engine, operate the engine stop lever several times. Make sure

that the engine stop cable moves freely and that the engine stop lever operates correctly.

1. Check the oil. See “How To Prepare The Engine”.

2. Fill the fuel tank. See “How To Prepare The Engine”.

3. Push the stop switch (A), if equipped, to the on position (Figure 27, 28).

4. Turn the fuel shut-off valve (B), if equipped, to the on position.

5. Move the throttle control, if equipped, to the fast position. Operate the engine in the fast

position.

6. Engines with primer: For most temperature conditions, ﬁrmly push the primer bulb (C)

three times. See Figure 26, 27, 29. In cooler weather, additional priming may be needed.

A warm engine will usually not require priming. Every time you push the primer button,

wait two seconds. Note: When starting a new engine for the ﬁrst time, push the primer

bulb ﬁve times.

Note: Excessive priming can ﬂood the carburetor with fuel. See “The Engine Will Not

Start” in the Troubleshooting section.

7. Self-propelled models: Make sure the drive lever (C) is in the disengaged position (D).

See Figure 24, 25.

8. Stand behind the mower. Use one hand to hold the engine stop lever (H) in the operating

position. See Figure 5. Use the other hand to hold the recoil starter handle (I).

9. Slowly pull the recoil starter handle until resistance is felt, then pull quickly to start the

engine. Slowly return the recoil starter handle.

10. If the engine does not start in 5 or 6 tries, see the Troubleshooting section.

Before Operation Of The Mower

WARNING: Check the condition of the grass bag for wear or deterioration. If

worn or damaged, replace the parts only with approved factory replacement

parts.

• To completely ll the grass bag (if equipped) operate the engine with the throttle control

(if equipped) in the fast position.

• Make sure the grass bag (if equipped) is properly mounted.

• Check the condition of the grass bag for wear or deterioration. If worn or damaged,

replace the parts only with factory authorized replacement parts or like parts.

How To Adjust The Height Of Cut

WARNING: The blade will rotate when the engine runs. Before you change the

height of cut, disconnect the spark plug wire and keep it away from the spark

plug.

Models With Individual Wheel Adjusters - Figure

To change the height of cut, move the position of the adjuster arm (A) at each wheel as follows.

1. Disengage the adjuster arm (A).

2. Move the adjuster arm to another position.

3. Make sure that each adjuster arm is in the same position so that the mower will cut level.

Models With Single-Lever Adjuster - Figure

To change the height of cut, move the position of the adjuster arm (B) as follows.

1. Disengage the adjuster arm (B).

2. Move the adjuster arm to another position.

How To Empty The Grass Bag - Figure

WARNING: Before you remove the grass bag, stop the engine. Before you

remove any grass from the mower housing, disconnect the spark plug wire and

keep it away from the spark plug.

1. Raise the rear door (F). See Figure 13.

2. Hold the handle (G) of the grass bag. Lift the frame assembly (H) over the rear door pivot

rod (I).

Not for

Reproduction

3. Empty the grass from the grass bag (E). See Figure 33.

How To Use As A Mulcher - Figure

WARNING: Before you install or remove the mulcher plug, disconnect the spark

plug wire and keep it away from the spark plug.

1. For mulching grass, remove the grass bag (I) and the side discharge chute (M) from the

mower. See Figure 1.

2. Raise the rear door (B) and install the mulcher plug (A) into the rear discharge opening.

See Figure 14.

Maintenance

Illustrations and pictorials begin on page 2.

Emissions Control

Maintenance, replacement, or repair of the emissions control devices and systems may be

performed by any non-road engine repair establishment or individual. However, to obtain “no

charge” emissions control service, the work must be performed by a factory authorized dealer.

See the Emissions Warranty.

WARNING: Before you make an inspection, adjustment, or repair, disconnect

the spark plug wire and keep it away from the spark plug.

Maintenance Chart

MOWER

Every 8 Hours or Daily

Check engine stop lever

Clean debris off mower

Every 25 Hours or Annually *

Check

mower for loose hardware

Every 50 Hours or Annually *

Clean battery and cables (if equipped)

See Dealer Annually to

Lubricate mower

Check mower blade stopping time

Check mower blades **

* Whichever comes ﬁrst

** Check blades more often in regions with sandy soils or high dust conditions.

ENGINE

First 5 Hours

Change engine oil

Every 8 Hours or Daily

Check engine oil level

Every 25 Hours or Annually *

Clean engine air ﬁlter and pre-cleaner (if equipped) **

Every 50 Hours or Annually *

Change engine oil

Replace oil ﬁlter (if equipped)

Annually

Replace air ﬁlter

Replace pre-cleaner (if equipped)

See Dealer Annually to

Inspect mufﬂer and spark arrester (if equipped)

Replace spark plug

Replace fuel ﬁlter (if equipped)

Clean engine air cooling system

* Whichever comes ﬁrst

** Clean more often in dusty conditions or when airborne debris is present.

Mower Maintenance

Engine Tipping - Figure

NOTICE: Do not tip the engine with the spark plug down. When you service the engine, inspect

the blade, or clean the bottom of the mower housing; make sure to always tip the engine with

the spark plug up. Transporting or tipping the engine with the spark plug down will cause the

following.

• hard starting

• engine smoking

• spark plug fouling.

• oil or fuel saturation of the air lter

How To Clean The Mower Housing

WARNING: The blade will rotate when the engine runs. Before you clean the

mower housing, stop the engine and disconnect the spark plug wire and keep it

away from the spark plug.

If grass and other debris accumulate on the bottom of the mower housing, performance will be

reduced. After you mow, clean the mower housing as follows.

1. Stop the engine.

2. Disconnect the wire from the spark plug.

3. Clean the top and the bottom of the mower housing.

How To Remove The Drive Belt

To remove or service the drive belt, take the mower to an approved service dealer.

How To Adjust The Drive Cable - Figure

WARNING: Before you adjust the drive cable, release the engine stop lever and

wait for the engine to stop.

If the drive system does not engage and disengage correctly, check the handle for correct as-

sembly. Make sure that all parts are in good condition, not broken or bent, and that all fasteners

are tight.

Worn parts will change the performance of the drive system. When you mow in high thick

grass or on hills, the drive system can slip if the drive cable is too loose. If the drive system

slips, adjust as follows or take the mower to an authorized service dealer.

1. If the drive system slips, turn the cable adjuster (A) one turn in the direction as shown

(Figure 39, 40). Operate the mower and test the drive system.

2. If the drive system still slips, turn the cable adjuster one more turn to shorten the cable.

Again, test the drive system.

3. Repeat the adjustment and test until the drive system does not slip.

4. Before you begin to mow, make sure the drive system will correctly disengage and that

the mower will stop. If the drive system will not disengage, take the mower to an autho-

rized service dealer before you operate the mower.

Not for

Reproduction

14 BriggsandStratton.com

Blade Service - Figure

WARNING: Before you inspect the blade (C) or the blade adapter (D), discon-

nect the spark plug wire and keep it away from the spark plug. If the blade hits

an object, stop the engine. Disconnect the wire to the spark plug. Check the unit

for damage.

Frequently check the blade (C) for wear or damage such as cracks. Frequently check the bolt

(A) that holds the blade. Keep the bolt tight. If the blade hits an object, stop the engine. Discon-

nect the wire to the spark plug. Check the blade adapter (D) for damage. Check for a bent or

damaged blade, a badly worn blade, or other damage. Before you operate the unit, damaged

parts must be replaced with factory authorized replacement parts or like parts. For safety,

replace the blade every two years. Keep a sharp edge on the blade. A blade that is not sharp will

cause the ends of the grass to become brown. To remove or service the blade, take the mower

to an approved service dealer.

Check The Level Of Cut

Test the unit in a small area. If the height of cut is not level or if the cut grass is not discharged

or does not cut even, see the Troubleshooting section.

Engine Maintenance

Carburetor Adjustment

Never make adjustments to the carburetor. The carburetor was set at the factory to operate

efﬁciently under most conditions. However, if adjustments are required, see any Briggs & Strat-

ton Authorized Dealer for service.

How To Change The Oil - Figure

WARNING

Fuel and its vapors are extremely ﬂammable and explosive.

Fire or explosion can cause severe burns or death.

• If you drain the oil from the top oil ll tube, the fuel tank must be empty or fuel can

leak out and result in a ﬁre or explosion.

Used oil is a hazardous waste product and must be disposed of properly. Do not discard with

household waste. Check with your local authorities, service center, or dealer for safe disposal/

recycling facilities.

Remove Oil

You can drain the oil from the bottom drain hole, the side drain hole, or from the top oil ﬁll tube.

1. With engine off but still warm, disconnect the spark plug wire and keep it away from the

spark plug.

2. The engine is equipped with a bottom drain and/or a side drain. Remove the oil drain

plug. Drain the oil into an approved container.

3. After the oil has drained, install and tighten the oil drain plug.

4. If you drain the oil from the top oil ﬁll tube (C, Figure 17, 18), keep the spark plug end of

the engine up. Drain the oil into an approved container.

WARNING: If you drain the oil from the top oil ﬁll tube, the fuel tank must be

empty or fuel can leak out and result in a ﬁre or explosion. To empty the fuel

tank, run the engine until it stops from lack of fuel.

Change The Oil Filter (if equipped)

Some models are equipped with an optional oil ﬁlter. For replacement intervals, see the Main-

tenance chart.

1. Drain the oil from the engine. See the How To Change The Oil section.

2. Remove the oil ﬁlter (D) and dispose of properly. See Figure 18.

3. Before you install the new oil ﬁlter, lightly lubricate the oil ﬁlter gasket with fresh, clean

oil.

4. Install the oil ﬁlter by hand until the gasket contacts the oil ﬁlter adapter, then tighten the

oil ﬁlter 1/2 to 3/4 turns.

5. Add oil. See the Add Oil section.

6. Start and run the engine. As the engine warms up, check for oil leaks.

7. Stop the engine and check the oil level. It should be at the top of the full indicator (B) on

the dipstick (Figure 18).

Add Oil

• Place engine level.

• Clean the oil ll area of any debris.

1. Remove the dipstick (A) and wipe with a clean cloth (Figure 17, 18).

2. Pour the oil slowly into the engine oil ﬁll (C). Do not overﬁll. After adding oil, wait one

minute and then check the oil level.

3. Install and tighten the dipstick.

4. Remove the dipstick and check the oil level. It should be at the top of the full indicator

(B) on the dipstick.

5. Install and tighten the dipstick.

How To Service The Air Filter - Figure

Follow the procedure that matches your speciﬁc air ﬁlter assembly.

NOTICE: Do not use pressurized air or solvents to clean the ﬁlter. Pressurized air can damage

the ﬁlter and solvents will dissolve the ﬁlter.

WARNING

Fuel and its vapors are extremely ﬂammable and explosive.

Fire or explosion can cause severe burns or death.

• Never start or run the engine with the air cleaner assembly (if equipped) or the air

ﬁlter (if equipped) removed.

Air Filter - Figure

1. Remove the screw (A) from the top of the air ﬁlter assembly (B). See Figure 35.

2. To prevent debris from falling into the carburetor, carefully remove the air ﬁlter assembly.

3. Remove the foam element (C) from the air ﬁlter base.

4. Wash the foam element in liquid detergent and water. Squeeze dry the foam element in a

clean cloth.

5. Saturate the foam element with clean engine oil. To remove the excess engine oil,

squeeze the foam element in a clean cloth.

6. Install the foam element into the air ﬁlter base.

7. Install the air ﬁlter assembly onto the carburetor and secure with screw.

Air Filter - Figure

1. Loosen the fastener (A) that holds the cover (B, Figure 36).

2. Open the cover and remove the pre-cleaner (C) and the ﬁlter (D).

3. To loosen debris, gently tap the ﬁlter on a hard surface. If the ﬁlter is excessively dirty,

replace with a new ﬁlter.

4. Wash the pre-cleaner in liquid detergent and water. Then allow it to thoroughly air dry.

Do not oil the pre-cleaner.

5. Assemble the dry pre-cleaner to the ﬁlter with the lip (E) of the pre-cleaner on the bottom

of the ﬁlter pleats.

6. Install the ﬁlter.

7. Install the cover tabs (F) into the slots (G).

8. Close the cover and secure with the fastener.

Air Filter - Figure

1. Loosen the fastener (A) that holds the cover (B). Remove the cover. See Figure 37.

2. Remove the pre-cleaner (C) and the ﬁlter (D).

3. To loosen debris, gently tap the ﬁlter on a hard surface. If the ﬁlter is excessively dirty,

replace with a new ﬁlter.

4. Wash the pre-cleaner in liquid detergent and water. Then allow it to thoroughly air dry.

Do not oil the pre-cleaner.

5. Assemble the dry pre-cleaner to the ﬁlter.

6. Install the ﬁlter and pre-cleaner into the base (E). Make sure ﬁlter ﬁts securely in the

base.

7. Install air ﬁlter cover and secure with fastener. Make sure the fastener is tight.

Air Filter - Figure

1. Open the cover (A) and remove the ﬁlter. See Figure 38.

2. For paper ﬁlters (B), gently tap the ﬁlter on a hard surface. If the ﬁlter is excessively dirty,

replace with a new ﬁlter.

3. For foam elements (C), wash the foam element in liquid detergent and water. Squeeze

dry the foam element in a clean cloth.Saturate the foam element with clean engine oil. To

remove the excess engine oil, squeeze the foam element in a clean cloth.

4. Install the ﬁlter/element and close the cover.

Storage

WARNING

Fuel and its vapors are extremely ﬂammable and explosive.

Fire or explosion can cause severe burns or death.

When Storing Fuel Or Equipment With Fuel In Tank

• Store away from furnaces, stoves, water heaters or other appliances that have pilot

lights or other ignition sources because they can ignite fuel vapors.

Fuel System

Fuel can become stale when stored over 30 days. Stale fuel causes acid and gum deposits to

form in the fuel system or on essential carburetor parts. To keep fuel fresh, use Briggs & Strat-

ton FRESH START

fuel stabilizer, available as a liquid additive or a drip concentrate cartridge.

There is no need to drain gasoline from the engine if a fuel stabilizer is added according to

instructions. Run the engine for 2 minutes to circulate the stabilizer throughout the fuel system.

The engine and fuel can then be stored up to 24 months.

If gasoline in the engine has not been treated with a fuel stabilizer, it must be drained into an

approved container. Run the engine until it stops from lack of fuel. The use of a fuel stabilizer in

the storage container is recommended to maintain freshness.

Not for

Reproduction

Engine Oil

While the engine is still warm, change the engine oil.

Folding Handle Storage

NOTICE: Be careful when you fold or raise the handle. Do not damage the cables. A cable that is

bent will not work correctly. Before you use the unit, replace a bent or damaged cable.

How To Fold The Handle - Figure

1. Loosen the knobs (A) that hold the upper handle (B) to the lower handle (C). See

Figure 42.

NOTICE: As you fold or raise the handle, make sure that the cables are not caught

between the upper and lower handles or around the handle fasteners.

2. Rotate the upper handle (B) toward the back of the unit. See Figure 43.

3. Remove the knobs (C) and fasteners that secure the lower handle (A) to the handle

bracket (D).

4. Rotate the handle forward over the engine as shown. Make sure that the cables are not

damaged.

How To Raise The Handle - Figure

1. Raise the lower handle (A) to the operating position (Figure 2).

2. The handle bracket (B) has two mounting holes (Figure 3). Use hole (C) to mount the

handle in the high position. Use hole (D) to mount the handle in the low position.

3. Mount the handle in either hole (C) or hole (D) with the fasteners as shown. Tighten

knobs (E) until the lower handle is secure.

4. Put the upper handle (G) in the operating position (Figure 4). Tighten the knobs (F) until

the upper handle and lower handle are locked in place.

How To Prepare The Mower For Storage

1. Clean the dirt and debris from the cylinder cooling ﬁns and the engine housing.

2. Clean the bottom of the mower housing.

3. Completely clean the mower to protect the paint.

4. Put the unit in a building that has good ventilation.

5. Make sure the grass bag is empty of grass. Grass remaining in the bag during storage

will damage the bag.

NOTICE: Store the engine level (normal operating position). If the engine is tipped for storage,

the fuel tank must be empty and the spark plug side must be up. If the fuel tank is not empty

and if the engine is tipped in any other direction, it may be difﬁcult to start due to oil or gasoline

contaminating the air ﬁlter and/or the spark plug.

How To Order Replacement Parts

Use only factory authorized replacement parts or like parts when making repairs. Do not use

attachments or accessories not speciﬁcally recommended for this product. In order to obtain

proper replacement parts you must supply the model number which is located on the product

nameplate.

When ordering the following information is required:

• Model Number

• Serial Number

• Part Number

• Quantity

Troubleshooting

The Engine will not start.

1. Make sure the fuel tank is ﬁlled with clean fuel. Do not use old fuel.

2. On a cold engine, push the primer button (optional on some models) three times.

3. Make sure the wire for the spark plug is connected to the spark plug.

4. There is too much fuel in the engine cylinder. Remove and dry the spark plug. Pull the

recoil starter handle several times. Install the spark plug. Connect the wire to the spark

plug. Start the engine.

5. The engine is difﬁcult to start in heavy or high grass. Move the mower to a clean dry

surface.

6. Make sure the engine stop lever is in the operating position.

7. Make sure the fuel valve is in the ON position.

The Engine will not stop.

1. Release the engine stop lever.

2. Check the engine stop cable. Replace the cable if bent or damaged.

The Engine performance is bad.

1. Check the height of cut settings. Raise the height of cut if the grass is high.

2. Check the bottom of the blade housing. Clean the blade housing of grass and other

debris.

3. Check the wire to the spark plug. Make sure the wire is connected.

4. Clean the engine cooling ﬁns of grass and other debris.

5. Check the spark plug gap. Set the spark plug gap at 0.76 mm (0.030 in).

6. Check the amount of oil in the engine. Fill with oil if necessary.

7. Check the engine air cleaner.

8. The fuel is bad. Drain and clean the fuel tank. Fill the fuel tank with clean fuel.

Excessive Vibration.

1. The blade is not balanced. Remove the blade and replace with a factory replacement

blade.

2. Check for a bent or broken blade. A damaged blade is dangerous and must be replaced.

3. Check the blade adapter. Replace a broken blade adapter.

4. If the vibration continues, take the mower to an authorized service dealer.

The grass will not discharge correctly.

1. Clean the bottom of the mower housing.

2. Check for a badly worn blade. Remove and sharpen the blade. For safety, replace the

blade every two years with a factory replacement blade.

The grass is not cut even.

1. Check the height adjustment at each wheel. The height adjustment must be the same for

each wheel.

2. Make sure the blade is sharp.

3. Check for a bent or broken blade. A damaged blade is dangerous and must be replaced.

4. Check for a broken blade adapter. Replace a broken blade adapter.

5. Move the throttle control (if equipped) to the fast or start position.

6. Check the throttle control (if equipped). Make sure that the throttle control is not in the

choke position.

7. Move the throttle control (if equipped) to the fast position.

Need Assistance? Go to BRIGGSandSTRATTON.COM.

Speciﬁcations

Engine and Tune-up Speciﬁcations - 500 Series Engines

Oil Capacity 18 - 20 oz. (0.54 - 0.59 L)

Spark Plug Gap 0.030 in (0.76 mm)

Spark Plug Torque 180 lb-in (20 Nm)

Engine and Tune-up Speciﬁcations - 500/550/575 E-Series Engines

Oil Capacity 15 oz. (0.44 L)

Spark Plug Gap 0.020 in (0.50 mm)

Spark Plug Torque 180 lb-in (20 Nm)

Engine and Tune-up Speciﬁcations - 625/675 Series Engines

Oil Capacity 18 - 20 oz. (0.54 - 0.59 L)

Spark Plug Gap 0.020 in (0.50 mm)

Spark Plug Torque 180 lb-in (20 Nm)

Engine and Tune-up Speciﬁcations - 800/850 Series Engines

Oil Capacity 18 - 20 oz. (0.54 - 0.59 L)

Spark Plug Gap 0.020 in (0.50 mm)

Spark Plug Torque 180 lb-in (20 Nm)

Not for

Reproduction

16 BriggsandStratton.com

BRIGGS & STRATTON POWER PRODUCTS GROUP, L.L.C. OWNER WARRANTY POLICY

LIMITED WARRANTY

Briggs & Stratton Power Products Group, LLC will repair and/or replace, free of charge, any part(s) of the equipment that is

defective in material or workmanship or both. Briggs & Stratton Corporation will repair and/or replace, free of charge, any

part(s) of the Briggs and Stratton engine* (if equipped) that is defective in material or workmanship or both. Transportation

charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is

effective for the time periods and subject to the conditions stated below. For warranty service, find the nearest Authorized

Service Dealer using our dealer locator at www.BriggsandStratton.com.

There is no other express warranty. Implied warranties, including those of merchantability and fitness for a particular

purpose, are limited to one year from purchase or to the extent permitted by law. Liability for incidental or consequential

damages are excluded to the extent exclusion is permitted by law.

Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do

not allow the exclusion or limitation of incidental or consequential damages, so the above limitation and exclusion may not

apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state

or country to country.

WARRANTY PERIOD

The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the

period of time stated above. “Consumer use” means personal residential household use by a retail consumer. “Commercial

use” means all other uses, including use for commercial, income producing or rental purposes. Once product has experienced

commercial use, it shall thereafter be considered as commercial use for purposes of this warranty.

No warranty registration is necessary to obtain warranty on Briggs & Stratton products. Save your proof of purchase receipt. If you

do not provide proof of the initial purchase date at the time warranty service is requested, the manufacturing date of the product will

be used to determine warranty eligibility.

ABOUT YOUR WARRANTY

We welcome warranty repair and apologize to you for being inconvenienced. Warranty service is available only through servicing

dealers authorized by Briggs & Stratton or BSPPG, LLC.

Most warranty repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. This warranty

only covers defects in materials or workmanship. It does not cover damage caused by improper use or abuse, improper

maintenance or repair, normal wear and tear, or stale or unapproved fuel.

Improper Use and Abuse - The proper, intended use of this product is described in the Operator’s Manual. Using the product in

a way not described in the Operator’s Manual or using the product after it has been damaged will void your warranty. Warranty is

not allowed if the serial number on the product has been removed or the product has been altered or modified in any way, or if the

product has evidence of abuse such as impact damage, or water/chemical corrosion damage.

Improper Maintenance or Repair - This product must be maintained according to the procedures and schedules provided in the

Operator’s Manual, and serviced or repaired using genuine Briggs & Stratton parts. Damage caused by lack of maintenance or use

of non-original parts is not covered by warranty.

Normal Wear - Like all mechanical devices, your unit is subject to wear even when properly maintained. This warranty does not

cover repairs when normal use has exhausted the life of a part or the equipment. Maintenance and wear items such as filters,

belts, cutting blades, and brake pads (engine brake pads are covered) are not covered by warranty due to wear characteristics

alone, unless the cause is due to defects in material or workmanship.

Stale Fuel - In order to function correctly, this product requires fresh fuel that conforms to the criteria specified in the Operator’s

Manual. Damage caused by stale fuel (carburetor leaks, clogged fuel tubes, sticking valves, etc) is not covered by warranty.

* Applies to Briggs and Stratton engines only. Warranty coverage of non-Briggs and Stratton engines is provided by the engine manufacturer.

Item Consumer Use Commercial Use:

Equipment 2 Years 90 Days

Engine* 2 Years 90 Days

Battery 1 Year 1 Year

Not for

Reproduction

California, U.S. EPA, and Briggs & Stratton Corporation Emissions Control Warranty Statement

Your Warranty Rights And Obligations

April 2011

The California Air Resources Board, U.S. EPA, and Briggs & Stratton (B&S) are pleased

to explain the emissions control system warranty on your Model Year 2011--2012

engine/equipment. In California, new small off-road engines and large spark ignited

engines less than or equal to 1.0 liter must be designed, built, and equipped to meet the

State’s stringent anti-smog standards. B&S must warrant the emissions control system

on your engine/equipment for the periods of time listed below provided there has been

no abuse, neglect, or improper maintenance of your engine or equipment.

Your emissions control system may include parts such as the carburetor or fuel injection

system, fuel tank, ignition system, and catalytic converter. Also included may be hoses,

belts, connectors, sensors, and other emissions-related assembli e s .

Where a warrantable condition exists, B&S will repair your engine/ equipment at no cost

to you including diagnosis, parts, and labor.

Manufacturer’s Warranty Coverage:

Small off-road engines and large spark ignited engines less than or equal to 1.0 liter are

warranted for two years. If any emissions-related part on your engine/equipment is

defective, the part will be repaired or replaced by B&S.

Owner ’s Warranty Responsibilities:

 As the engine/equipment owner, you are responsible for the performance of the

required maintenance listed in your owner’s manual. B&S recommends that you

retain all receipts covering maintenance on your engine/equipment, but B&S cannot

deny warranty solely for the lack of receipts or your failure to ensure the performance

of all scheduled maintenance.

 As the engine/equipment owner, you should however be aware that B&S may deny

you warranty coverage if your engine/equipment or a part has failed due to abuse,

neglect, improper maintenance, or unapproved modifications.

 You are responsible for presenting your engine/equipment to a B&S distribution

center, servicing dealer, or other equivalent entity, as applicable, as soon as a

problem exists. The warranty repairs should be completed in a reasonable amount of

time, not to exceed 30 days. If you have any questions regarding your warranty

rights and responsibilities, you should contact B&S at (414) 259-5262.

Briggs & Stratton Emissions Control Warranty Provisions

The following are specific provisions relative to your Emissions Control Warranty Coverage. It is in addition to the B&S engine warranty for non-regulated engines found in the

Operator’s Manual.

1. Warranted Emissions Parts

Coverage under this warranty extends only to the parts listed below (the emissions

control systems parts) to the extent these parts were present on the B&S engine

and/or B&S supplied fuel system.

a. Fuel Metering System

 Cold start enrichment system (soft choke)

 Carburetor and internal parts

 Fuel pump

 Fuel line, fuel line fittings, clamps

 Fuel tank, cap and tether

 Carbon canister

b. Air Induction System

 Air cleaner

 Intake manifold

 Purge and vent line

c. Ignition System

 Spark plug(s)

 Magneto ignition system

d. Catalyst System

 Catalytic converter

 Exhaust manifold

 Air injection system or pulse valve

e. Miscellaneous Items Used in Above Systems

 Vacuum, temperature, position, time sensitive valves and switches

 Connectors and assemblies

2. Length of Coverage

For a period of two years from date of original purchase, B&S warrants to the original

purchaser and each subsequent purchaser that the engine is designed, built, and

equipped so as to conform with all applicable regulations adopted by the Air

Resources Board; that it is free from defects in material and workmanship that could

cause the failure of a warranted part; and that it is identical in all material respects to

the engine described in the manufacturer’s application for certification. The warranty

period begins on the date the engine is originally purchased.

The warranty on emissions-related parts is as follows:

 Any warranted part that is not scheduled for replacement as required

maintenance in the owner’s manual supplied, is warranted for the warranty

period stated above. If any such part fails during the period of warranty

coverage, the part will be repaired or replaced by B&S at no charge to the

owner. Any such part repaired or replaced under the warranty will be warranted

for the remaining warranty period.

 Any warranted part that is scheduled only for regular inspection in the owner’s

manual supplied, is warranted for t h e w arranty period stated above. Any such

part repaired or replaced under warranty will be warranted for the remaining

warranty period.

 Any warranted part that is scheduled for replacement as required maintenance

in the owner’s manual supplied, is warranted for the period of time prior to the

first scheduled replacement point for that part. If the part fails prior to the first

scheduled replacement, the part will be repaired or replaced by B&S at no

charge to the owner. Any such part repaired or replaced under warranty will be

warranted for the remainder of the period prior to the first scheduled

replacement point for the part.

 Add on or modified parts that are not exempted by the Air Resources Board

may not be used. The use of any non exempted add on or modified parts by the

owner will be grounds for disallowing a warranty claim. The manufacturer will

not be liable to warrant failures of warranted parts caused by the use of a non

exempted add on or modified part.

3. Consequential Coverage

Coverage shall extend to the failure of any engine components caused by the

failure of any warranted emissions parts.

4. Claims and Coverage Exclusions

Warranty claims shall be filed according to the provisions of the B&S engine

warranty policy. Warranty coverage does not apply to failures of emissions parts

that are not original equipment B&S parts or to parts that fail due to abuse, neglect,

or improper maintenance as set forth in the B&S engine warranty policy. B&S is not

liable for warranty coverage of failures of emissions parts caused by the use of

add-on or modified parts.

Look For Relevant Emissions Durability Period and Air Index Information

On Your Small Off-Road Engine Emissions Label

Engines that are certified to meet the California Air Resources Board (CARB) small

off-road Emissions Standard must display information regarding the Emissions Durability

Period and the Air Index. Briggs & Stratton makes this information available to the

consumer on our emissions labels. The engine emissions label will indicate certification

information.

The Emissions Durability Period describes the number of hours of actual running time

for which the engine is certified to be emissions compliant, assuming proper

maintenance in accordance with the Operating & Maintenance Instructions. The

following categories are used:

Moderate:

Engine is certified to be emissions compliant for 125 hours of actual engine running time.

Intermediate:

Engine is certified to be emissions compliant for 250 hours of actual engine running time.

Extended:

Engine is certified to be emissions compliant for 500 hours of actual engine running time.

For example, a typical walk-behind lawn mower is used 20 to 25 hours per year.

Therefore, the Emissions Durability Period of an engine with an intermediate rating

would equate to 10 to 12 years.

Briggs & Stratton engines are certified to meet the United States Environmental

Protection Agency (USEPA) Phase 2 or Phase 3 emissions standards. The Emissions

Compliance Period referred to on the Emissions Compliance label indicates the number

of operating hours for which the engine has been shown to meet Federal emissions

requirements.

For engines less than 225 cc displacement.

Category C = 125 hours, Category B = 250 hours, Category A = 500 hours

For engines of 225 cc or more displacement.

Category C = 250 hours, Category B = 500 hours, Category A = 1000 hours

Not for

Reproduction

BriggsandStratton.com8

Nous vous remercions d’avoir acheté ce produit de qualité. Nous sommes heureux de la

conﬁance que vous accordez à notre marque. S’il est utilisé et entretenu selon les instructions

de ce manuel, votre produit vous procurera de nombreuses années de service ﬁable.

Ce manuel contient des informations de sécurité pour vous faire connaître les dangers et les

risques associés à cette machine et la façon de les éviter. Cette machine est conçue et faite uni-

quement pour la tonte soignée de gazons bien entretenus et elle n’est destinée à aucune autre

utilisation. Il est important de lire et comprendre parfaitement ces instructions avant d’essayer

de mettre en marche ou de faire fonctionner cet équipement. Conservez ces instructions

d’origine pour vous y reporter dans le futur.

Fournissez les informations suivantes sur votre achat.

Date d’achat________________________________________________________________

Revendeur_________________________________________________________________

Numéro de téléphone du revendeur______________________________________________

Machine

Numéro du modèle_____________________________________________________

Numéro de série_______________________________________________________

Moteur

Modèle_________________Type________________Code______________________

Puissance nominale

Les étiquettes de puissance nominale brute pour les modèles de moteurs à essence individuels

répondent au code J1940 (Small Engine Power & Torque Rating Procedure) de la SAE (Society

of Automotive Engineers) ; et la performance nominale a été obtenue et corrigée conformément

à SAE J1995 (Révision 2002-05). Les valeurs de couple sont dérivées à 3 060 tr/min ; les

valeurs de puissance sont dérivées à 3 600 tr/min. Les courbes de puissance brute peuvent

être consultées sur le site www.BRIGGSandSTRATTON.COM. Les valeurs données pour la

puissance nette sont mesurées avec l’échappement ou le ﬁltre à air installé tandis que les

valeurs données pour la puissance brute sont recueillies sans ces accessoires. La puissance

brute du moteur sera plus élevée que la puissance nette du moteur et elle affectée, entre autres,

par les conditions atmosphériques de fonctionnement et les variations entre les moteurs. Étant

donné la gamme étendue de produits sur lesquels les moteurs sont placés, il se peut que le

moteur à essence ne développe pas la puissance nominale brute quand il est utilisé sous une

version spéciﬁque d’alimentation électrique. Cette différence est due à différents facteurs, y

compris, mais sans toutefois s’y limiter, la diversité des composants du moteur (ﬁltre à air,

échappement, chargement, refroidissement, carburateur, pompe à carburant, etc.), la limite

des applications, les conditions atmosphériques de fonctionnement (température, humidité,

altitude) et les variations entre les moteurs. En raison des limites de fabrication et de capacité,

Briggs & Stratton peut substituer un moteur d’une puissance nominale supérieure pour le

moteur de cette série.

Contenu

Illustrations ............................................................................................................................... 2

Sécurité de l'opérateur ................................................................................................................ 8

Fonctions et commandes .......................................................................................................... 10

Pictogrammes ........................................................................................................................... 11

Montage ............................................................................................................................. 11

Fontionnement .......................................................................................................................... 12

Entretien ............................................................................................................................. 13

Dépannage ............................................................................................................................. 15

Spéciﬁcations ............................................................................................................................ 16

Politique de garantie ................................................................................................................. 17

Sécurité de l'opérateur

Symboles et avertissements

Le symbole de sécurité est utilisé pour identiﬁer des informations de sécurité sur les

dangers pouvant entraîner des blessures corporelles. Un mot-indicateur (DANGER,

AVERTISSEMENT ou MISE EN GARDE) est utilisé avec le symbole de sécurité pour indiquer la

probabilité et la gravité potentielle des blessures. En outre, un symbole de danger peut être

utilisé pour représenter le type de danger.

DANGER indique un danger qui, s’il n’est pas écarté, entraînera la mort ou

de graves blessures.

AVERTISSEMENT indique un danger qui, s’il n’est pas écarté, pourrait entraîner la

mort ou de graves blessures.

MISE EN GARDE indique un danger qui, s’il n’est pas écarté, pourrait être cause

de blessures légères ou modérées.

REMARQUE indique une situation qui pourrait endommager l’équipement.

AVERTISSEMENT :

Certains composants de cet équipement et de ses acces-

soires contiennent des produits chimiques reconnus dans l’état de Californie

comme étant cause de cancer, d’anomalies congénitales ou d’autres effets

néfastes sur la fonction de reproduction. Se laver les mains après manipulation.

AVERTISSEMENT : L’échappement du moteur de cet appareil contient des

produits chimiques connus selon l’état de la Californie de causer le cancer, des

anomalies congénitales ou autre effet nuisible à la reproduction.

AVERTISSEMENT : L’utilisation ou le fonctionnement du moteur sur des

terrains forestiers, broussailleux ou herbeux constituent une violation de la

Section 4442 du Code des ressources publiques de Californie, à moins que le

système d’échappement ne soit équipé d’un pare-étincelles, comme le définit

la Section 4442, maintenu en bon état de marche. D’autres provinces ou

juridictions fédérales peuvent avoir des lois similaires. Contacter le fabriquant, détaillant ou

revendeur d’origine de l’équipement pour obtenir un pare-étincelles conçu pour le système

d’échappement installé sur ce moteur.

Responsabilité du propriétaire

AVERTISSEMENT : Cette machine très puissante peut provoquer l'amputa-

tion d'une main ou d'un pied ou le jet d'objets pouvant causer des blessures

ou détériorations! Le fait de ne pas satisfaire les instructions de SECURITÉ

suivantes pourrait causer des blessures graves ou la mort de l'opérateur ou

d'autres personnes.

Le propriétaire de cette machine doit comprendre ces instructions et doit permettre uniquement

que des personnes qui les comprennent puissent opérer la machine. Toute personne utilisant

cette machine doit être saine d'esprit et de corps et ne doit pas être sous l'influence d'une

substance quelconque pouvant modifier sa vision, sa dextérité ou sa capacité de jugement. Si

vous avez des questions sur la machine que votre distributeur ne peut pas répondre, contactez

le service clientèle.

Sécurité de fonctionnement

Un matériel électrique est sûr tant que l’est son utilisateur. Il peut être dangereux s’il n’est pas

utilisé à bon escient ou s’il n’est pas correctement entretenu ! Rappel : l’utilisateur est respon-

sable de sa propre sécurité et de celle de ceux qui sont à ses côtés.

Faire preuve de bon sens et bien penser à ce que l’on fait. En cas de doute sur une opération

à effectuer sans danger avec l’équipement choisi, s’adresser à un professionnel : Contacter le

distributeur local homologué.

Lecture du manuel

Le manuel d’utilisation comporte d’importantes informations relatives à la sécurité qu’il faut

connaître AVANT d’utiliser la machine ainsi que PENDANT son fonctionnement.

Not for

Reproduction

Ce manuel comporte des techniques de fonctionnement en toute sécurité, une explication des

caractéristiques et des commandes de la machine et des informations relatives à l’entretien

pour profiter au maximum de l’investissement dans la machine.

S’assurer de lire, dans son intégralité, la section sur les règles et informations relatives à la

sécurité figurant dans les pages suivantes. Lire également la section sur le fonctionnement

dans son intégralité.

Enfants

Des accidents tragiques peuvent se produire avec des enfants. Ne jamais leur permettre de

se tenir à proximité de la zone d’opération. Les enfants sont souvent attirés par la machine et

l’activité de tonte. Ne jamais supposer que les enfants resteront là où ils ont été vus pour la

dernière fois. S’il existe un risque que des enfants puissent venir à proximité de l’endroit où l’on

tond, demander à un autre adulte responsable de les surveiller.

Fonctionnement en pente

20.0 ft

(6.0 m)

3.5 ft

(1.5 m)

Il existe un danger grave de blessure, voire de mort, en cas d’utilisation de cette machine dans

une pente trop raide. Utiliser la machine sur une pente trop raide ou sur laquelle la stabilité ou

la traction est inadéquate peut entraîner la perte de contrôle ou la chute et glissade.

Vous ne devez pas utiliser la machine sur des pentes de déclivité supérieure 10 degrées, ce

qui est 1,5 m (3,5 pi) d’élévation pour 6,0 m (20,0 pi). Toujours tondre les pentes en travers et

jamais de haut en bas.

Noter également que la surface que vous êtes entrain de tondre peut considérablement affecter

le contrôle. De l’herbe mouillée ou des feuilles peuvent gravement affecter votre stabilité et

traction sur une pente. En cas de doute sur l’utilisation de l’unité sur un plan incliné, ne pas

l’utiliser. Ça ne vaut pas le coup.

Pièces en mouvement

Cette machine comporte des pièces en mouvement qui peuvent blesser l’utilisateur ou autrui.

Néanmoins si vous vous tenez derrière la poignée correctement et suivez scrupuleusement

toutes les règles figurant dans ce manuel, il n’y a aucun danger à se servir de cette machine.

Le plateau de coupe de la tondeuse comporte une lame de tondeuse rotative susceptible

d’amputer les mains et les pieds. Ne jamais laisser qui que ce soit près de la machine quand

elle est en marche !

Pour vous aider, vous l’utilisateur, à utiliser ce matériel en toute sécurité, il est équipé d’un sys-

tème de sécurité détectant la présence du conducteur. NE PAS tenter d’altérer ni de contourner

le dispositif. Consulter le distributeur immédiatement si le dispositif ne réussit pas tous les

tests du système de verrouillage de sécurité figurant dans ce manuel.

Objets projetés

Cette unité comporte une lame de tondeuse rotative. Cette lame peut ramasser et projeter des

débris susceptibles de gravement blesser un spectateur. S’assurer de bien nettoyer la zone à

tondre AVANT de commencer à tondre.

Ne pas utiliser cette unité avant d’avoir mis le bac de ramassage complet ou la protection

d’évacuation (déflecteur) en place.

En outre, ne jamais laisser qui que ce soit près de la machine quand elle est en marche ! Si

quelqu’un se trouve dans la zone, arrêter immédiatement la machine et attendre que cette

personne parte.

Accumulation de débris

L’accumulation d’herbe et de débris peut provoquer un incendie. S’assurer de nettoyer toute

accumulation d’herbe et de débris avec une brosse ou de l’air comprimé, avant et après utilisa-

tion.

Carburant et entretien

L’essence est extrêmement inflammable. Ses vapeurs sont également extrêmement inflam-

mables et peuvent se déplacer vers des sources de combustion à distance. Utiliser l’essence

uniquement comme carburant, non pas comme solvant ou nettoyant. Ne jamais remiser

l’essence dans des endroits où ses vapeurs peuvent s’accumuler ou se déplacer vers une

source de combustion telle qu’une veilleuse. Le carburant doit être remisé dans des bidons en

plastique, hermétiques et homologués, ou dans le réservoir d’essence du tracteur, le bouchon

étant bien fermé. Essuyer immédiatement toute éclaboussure d’essence.

Un entretien adéquat est essentiel à la sécurité et à la performance de la machine. S’assurer

d’effectuer les procédures d’entretien indiquées dans ce manuel et surtout, de tester péri-

odiquement le dispositif de sécurité.

Instructions importantes pour la sécurité de l’utilisateur

Protection des enfants

Des accidents tragiques peuvent se produire lorsque l'opérateur n'est pas averti de la présence

d'enfants. Les enfants sont souvent attirés par la machine et l'activité de tonte. Ne jamais

supposer que les enfants resteront là où ils ont été vus pour la dernière fois.

1. Les enfants DOIVENT être éloignés de la zone de tonte et sous la stricte vigilance d'un

adulte autre que l'opérateur.

2. NE JAMAIS autoriser que les enfants restent sur le terrain à tondre lorsque la machine

est en fonctionnement. Éteindre cette dernière si quelqu'un rentre dans la zone de tonte.

3. NE PERMETTEZ PAS à des adolescents d'utiliser la machine.

4. PERMETTEZ uniquement aux adultes responsables et aux adolescents faisant preuve de

maturité dans leur jugement sous étroite supervision d’un adulte d'utiliser la machine.

5. NE JAMAIS tirer la tondeuse vers l'arrière à moins que ce ne soit vraiment nécessaire.

REGARDEZ partout pour VOIR s'il y a des enfants, des animaux ou des obstacles avant

et pendant la marche arrière.

6. Faire preuve DE PRUDENCE à l'approche d'angles morts, d'arbustes, d'arbres et d'autres

objets susceptibles de masquer la vision.

Fonctionnement en pente

1. Les pentes sont une des raisons principales des accidents liés aux chutes ou glissades.

Ils peuvent causer des blessures graves. Faire preuve de prudence supplémentaire sur

toutes les pentes. Si vous ne vous sentez pas à l'aise sur une pente, NE LA TONDEZ PAS.

2. Tondre les pentes en travers et jamais de haut en bas. Faire preuve d'extrême PRU-

DENCE lorsque vous changez la direction de la machine sur une pente. NE PAS tondre

sur des pentes raides (maximum 10 degrés) ou d’autres endroits où la stabilité ou la

traction est contestable.

3. Faites extrêmement attention lors de l’utilisation de bac à herbes ou d’autres acces-

soires ; ils affectent la conduite et la stabilité de la machine.

Préparation

1. Il est important que vous lisiez, compreniez et suiviez les instructions de ce manuel et

se trouvant sur la machine, le moteur et les accessoires. Veuillez vous familiariser avec

les commandes de la machine et apprendre à l'utiliser de manière adéquate avant de la

mettre en marche.

2. Seules les personnes responsables et mûres peuvent opérer cette machine et unique-

ment après qu'elles aient été formées de manière adéquate.

3. Les données indiquent que les utilisateurs, âgés d'au moins 60 ans, sont impliqués

dans un fort pourcentage des blessures associées à la tondeuse. Ces utilisateurs doivent

Not for

Reproduction

BriggsandStratton.com10

évaluer leur capacité à faire fonctionner la machine de manière suffisamment sûre pour

se protéger et protéger autrui de toute blessure grave.

4. Veuillez manipuler l'essence avec la plus grande des précautions. Les carburants

sont inflammables et les vapeurs sont explosives. Utilisez uniquement un récipient à

essence homologué. NE PAS enlever le bouchon du réservoir de carburant ou ajouter

de l'essence lorsque le moteur est en fonctionnement. Ajouter de l'essence lorsque la

machine est à l'extérieur et uniquement si le moteur est arrêté et froid. Veuillez essuyer

les éclaboussures de carburant sur la machine. NE PAS fumer.

5. Vérifier la zone à tondre et enlever tous les objets, tels que les jouets, les câbles, les

branches, les cailloux, et autres objets qui pourraient causer des blessures s'ils étaient

projetés par une lame ou s'ils interféraient avec la tonte. Veuillez également observer

l'emplacement des trous, des obstacles et d'autres possibles dangers.

6. Veuillez maintenir les personnes et les animaux en dehors de la zone de tonte. Veuillez

immédiatement ARRÊTER les lames, le moteur et la machine si quelqu'un rentre dans la

zone de tonte.

7. Veuillez vérifier fréquemment les commandes des protecteurs, déflecteurs, interrupteurs,

et autres dispositifs de sécurité.

8. Veuillez vérifier que les étiquettes de sécurité sont toutes clairement lisibles. Remplacez-

les si elles sont endommagées.

9. Veuillez vous protéger lorsque vous tondez. Portez des lunettes de sécurité, un masque

contre la poussière, des pantalons longs et des chaussures résistantes. NE TONDEZ pas

pieds nus ou avec des sandales.

10. Apprenez comment ARRÊTER les lames et le moteur rapidement afin d'être prêt à toute

urgence.

11. Faire très attention lors du chargement ou du déchargement de la machine sur une

remorque ou un camion.

12. Vérifiez les composants du bac à ramassage afin de contrôler leur usure ou détérioration.

Remplacez-les si nécessaire afin d'empêcher que des objets projetés, passant à travers

des trous endommagés ou usés, ne blessent quelqu'un.

Manipulation sans danger de l'essence

Afin d'éviter toute blessure ou d'endommager un bien, veuillez manipuler l'essence avec pré-

caution extrême. L'essence est extrêmement inflammable et ses vapeurs sont explosives.

1. Éteindre cigarettes, cigares, pipes et autres sources de combustion.

2. Utilisez uniquement un récipient à essence homologué.

3. NE PAS enlever le bouchon du réservoir de carburant ou ajouter de l'essence lorsque le

moteur est en fonctionnement. Laisser le moteur refroidir avant de faire le plein.

4. NE PAS remplir le réservoir d'essence alors que la machine se trouve à l'intérieur d'un

espace.

5. NE PAS remiser la machine ou le bidon de carburant où il y a une flamme nue, une étin-

celle ou une veilleuse, comme près d'un chauffe-eau ou de tout autre appareil ménager.

6. NE remplissez PAS des récipients à l'intérieur d'un véhicule, d'un camion ou d'une

remorque avec une bâche en plastique. Toujours placer les bidons sur le sol, éloignés de

tout véhicule, avant de les remplir.

7. Retirer tout équipement à essence du camion ou de la remorque et faire le plein sur le

sol. Quand cela n'est pas possible, faire le plein de la machine avec un bidon portable

plutôt qu'avec un distributeur d'essence.

8. NE PAS démarrer des équipements à essence près des véhicules ou des remorques.

9. Garder le bec en contact avec le bord du réservoir d'essence ou de l'ouverture du bidon à

tout moment jusqu'à obtention du plein. NE PAS utiliser de dispositif à ouverture bloquée

de bec.

10. En cas d'éclaboussures d'essence sur les vêtements, en changer immédiatement.

11. NE JAMAIS REMPLIR en excès le réservoir de carburant. Remettre le bouchon d'essence

en place et bien serrer.

Fontionnement

1. NE JAMAIS placer les mains ou les pieds près ou en-dessous des pièces en mouvement.

Veuillez maintenir la zone de décharge libre de toute personne lorsque le moteur est en

fonctionnement.

2. ARRÊTER le moteur lorsque vous traversez des chemins, routes, allées en gravier, et

chaque fois que la machine peut projeter des objets.

3. N'utiliser la machine qu'à la lumière du jour ou dans une lumière artiﬁcielle de bonne

qualité.

4. NE PAS utiliser la machine sous l'emprise de l'alcool ou de drogues.

5. Si vous avez cogné un obstacle ou si la tondeuse vibre de manière anormale, ARRÊTEZ

le moteur, et déconnectez en toute sécurité le câble de la bougie. Contrôlez si la tondeuse

a été endommagée et réparez-la avant de la faire fonctionner de nouveau.

6. NE PAS tondre à proximité d'à-pics, de fossés ou de talus. L'opérateur peut perdre

l'équilibre.

7. FAITES ATTENTION aux trous et autres obstacles dangereux. L'herbe haute peut cacher

des obstacles. Maintenir éloigné des fossés, des caniveaux, des clôtures et des objets en

saillie.

8. NE PAS tondre de l'herbe mouillée. Maintenir toujours l'équilibre. Tenir fermement la

poignée et marcher, ne jamais courir. Les glissades peuvent être source de blessures

graves.

9. RESTER TOUJOURS derrière la poignée lorsque le moteur est en fonctionnement.

10. NE JAMAIS quitter la machine si le moteur est en fonctionnement. ARRÊTER LA LAME

et ARRÊTER LE MOTEUR avant de quitter la position du conducteur pour quelque raison

que ce soit.

11. Lors du nettoyage, des réparations ou des inspections, s'assurer que le moteur, la lame

et toutes les pièces en mouvement sont arrêtés. Débrancher en toute sécurité le câble de

la bougie aﬁn d'empêcher le démarrage accidentel de la machine.

12. ARRÊTER le moteur et attendre que la lame se soit totalement ARRÊTÉE avant d'enlever

le sac à herbe et/ou de nettoyer l'herbe.

13. NE PAS utiliser la tondeuse sans le bac à ramassage, les protections de décharge, les

protections arrières ou autres dispositifs de sécurité. NE PAS orienter la décharge vers

des personnes, des voitures, des fenêtres ou des portes.

14. NE PAS décharger du matériel contre un mur ou une obstruction. Le matériau risque de

ricocher vers l'opérateur.

15. Ralentir avant de tourner.

16. Surveiller la circulation lors de l'utilisation à proximité des routes ou en les traversant.

17. NE PAS faire fonctionner le moteur dans des espaces fermés. Les gaz d'échappement du

moteur contiennent du monoxyde de carbone qui est un poison mortel.

18. Utilisez uniquement des accessoires approuvés par le fabricant. Voir les instructions du

fabricant pour le bon fonctionnement et l’installation des accessoires.

Entretien et remisage

1. NE PAS remiser la machine ou le bidon de carburant dans un espace où les fumées

peuvent atteindre une ﬂamme nue, une étincelle ou une veilleuse, comme près d'un

chauffe-eau, une chaudière, un sèche-linge ou tout autre appareil à gaz. Laisser le moteur

refroidir avant de remiser la machine dans un endroit clos. Remiser les récipients de

carburant dans un endroit où les enfants ne peuvent pas les atteindre, et qui soit bien

aéré et inhabité.

2. 2. Veuillez enlever le gazon, les feuilles et tout excès de graisse du moteur aﬁn d'éviter

les incendies et la surchauffe de ce dernier.

3. Lorsque vous réalisez la vidange du réservoir de carburant, videz l'essence dans un

récipient approuvé et au sein d'un espace ouvert loin de toute ﬂamme nue.

4. Veuillez bien serrer tous les boulons (en particulier les boulons de la lame), écrous et vis.

Vériﬁer que toutes les goupilles fendues soient en bonne position.

5. Contrôler que le moteur soit bien aéré lors du fonctionnement. Les gaz d'échappement

du moteur contiennent du monoxyde de carbone qui est un poison mortel.

6. Réparer le moteur et réaliser des réglages uniquement lorsque ce dernier est à l'arrêt.

Enlever le câble de la bougie de cette dernière et placez-le dans un endroit éloigné de la

bougie aﬁn d'empêcher tout démarrage accidentel.

7. NE PAS changer les paramètres du régulateur de vitesse du moteur ni emballer le

moteur.

8. Vériﬁer le sac à herbe fréquemment aﬁn de voir s'il est usé ou détérioré et éviter que

des objets ne soient projetés et l'exposition aux pièces en mouvement. Remplacer avec

un nouveau sac si vous observez que les jonctions sont desserrées ou des déchirures.

Remplacer la glissière ou l'adaptateur du sac s'il est cassé ou fêlé.

9. Les lames de la tondeuse sont aiguisées et peuvent couper. Emballez les larmes ou

portez des gants résistants, et faites preuve de la plus grande des PRÉCAUTIONS lorsque

vous les manipulez.

10. NE PAS essayer l'étincelle avec une mise à terre proche des puits de bougie ; la bougie

d'allumage pourrait enﬂammer les gaz sortant du moteur.

11. Faites réviser la machine par un revendeur agréé au moins une fois par an et faites

installer par le revendeur tout nouveau dispositif de sécurité.

12. Utiliser uniquement des pièces de rechange d’origine autorisées ou identiques

quand vous faites des réparations.

Utilisation souhaitée/limites d’utilisation

La tondeuse à pousser est conçue pour couper le gazon. Toute autre utilisation n’est pas per-

mise. Elle n’est pas conçue pour couper de l’herbe de plus de 15 cm de longueur ou de l’herbe

mêlée à de mauvaises herbes. La tondeuse poussée est uniquement adaptée à une utilisation

privée dans le jardin d’une maison. Elle n’est pas adaptée pour couper l’herbe dans les parcs

publics ou les terrains de jeu.

Fonctions et commandes

AVIS : Les dessins, illustrations et pictogrammes de ce manuel sont fournis à titre de référence

uniquement et peuvent ne pas correspondre à votre modèle spéciﬁque.

Comparez les caractéristiques et commandes suivantes avec celles de votre modèle (Figure 1).

Assurez-vous de bien connaître les endroits où elles se situent et de comprendre leur ﬁnalité.

A. Levier d'arrêt du moteur

B. Poignée supérieure

C. Bouton ou levier de blocage

D. Poignée inférieure

E. Volet arrière

F. Moteur

G. Réglage de la hauteur

H. Plaque signalétique

I. Sac à herbe

J. Poignée de lanceur manuel

K. Levier d’entraînement (modèles autopropulsés)

L. Bac de déchiqueteuse

M. Goulette d’éjection latérale

N. Couvercle de déchiqueteuse

Not for

Reproduction

La page charge ...

Simplicity WALKBEHIND MOWER, SNAPPER, FC MODELS S(P)19550EX Manuel utilisateur

Marque: Simplicity

Modèle: WALKBEHIND MOWER, SNAPPER, FC MODELS S(P)19550EX

Catégorie: Tondeuses à gazon

Taper: Manuel utilisateur

Ce manuel convient également à

881545-00

Télécharger le PDF

rapport

dans d''autres langues

English: Simplicity WALKBEHIND MOWER, SNAPPER, FC MODELS S(P)19550EX User manual

Simplicity WALKBEHIND MOWER, SNAPPER, FC MODELS S(P)19550EX Manuel utilisateur

Ce manuel convient également à

Simplicity WALKBEHIND MOWER, SNAPPER, FC MODELS S(P)19550EX Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents