Kenmore Intuition Mode d'emploi

Catégorie
Aspirateurs
Taper
Mode d'emploi
Model/Modelo/Modèle: BU4050
Bagged Upright Vacuum
with Hair EliminatorBrushroll
Aspiradora Con Bolsa Con Hair
Eliminator
Aspirateur Vertical Muni De Sac d’un
Hair Eliminator
www.kenmorefloorcare.com
Vacuum Cleaner Help Line:
1-844-608-3080 (US) / 1-844-608-3081 (CA)
8:00am-5:00pm EST, M-F
Use & Care Guide
Manual de Uso y Cuidado
Manuel d'entretien et d'utilisation
- 2 -
Before Using Your New Vacuum Cleaner ........................................................................2
Packing List .....................................................................................................................2
Important Safety Instructions ........................................................................................3-4
Vacuum Cleaner Warranty ..............................................................................................5
Parts and Features ........................................................................................................6-7
Assembly Instructions ...................................................................................................8-9
Operating Instructions ...............................................................................................10-16
Performance/Safety Features ....................................................................................16-17
Vacuum Maintenance and Care ................................................................................ 18-24
Troubleshooting ........................................................................................................25-26
Requesting Assistance or Service ......................................................................Back Cover
TABLE OF CONTENTS
PACKING LIST
Your KENMORE INTUITION ® BAGGED UPRIGHT VACUUM CLEANER is packaged with
the following parts and components assembled separately in the carton:
1 Upright Vacuum Cleaner
1 Handle
1 Wand
1 Crevice Tool
1 Flexible Hose
1 Upholstery Tool
1 Pet HandiMate®
1 Deluxe Dusting Brush
6 Dust Bags (one dust bag is
pre-installed in the vacuum)
1 Use & Care Guide
Read this Use & Care Guide. It will help you assemble and operate your new Kenmore
vacuum cleaner in the safest and most effective way.
For more information about vacuum cleaner care and operation, call the Vacuum Cleaner
Help Line at 1-844-608-3080 (US) / 1-844-608-3081 (CA). You will need the complete
model and serial numbers when requesting information.
Your vacuum cleaner’s model and serial numbers are located on the Model and Serial
Number Plate. Use the space below to record the model number and serial number of your
new Kenmore vacuum cleaner.
Model No.____________________________________________
Serial No. ____________________________________________
Date of Purchase ______________________________________
Keep this book and your sales check (receipt) in a safe place for future reference.
BEFORE USING YOUR NEW VACUUM CLEANER
- 3 -
WARNING!
Your safety is important to us. To reduce the risk of fire, electrical shock, injury to persons
or damage when using your vacuum cleaner, follow basic safety precautions including the
following:
IMPORTANT SAFETY INSTRUCTIONS
• Use your vacuum cleaner only as
described in this Use & Care Guide. Use
only with manufacturer’s recommended
attachments.
• Disconnect electrical supply before
servicing or cleaning out the brushroll
area. Failure to do so could result in the
brushroll unexpectedly starting, causing
personal injury from moving parts.
• Do not leave vacuum cleaner when
plugged in. Unplug from outlet when
not in use and before performing
maintenance.
• To reduce the risk of electrical shock - Do
not use outdoors or on wet surfaces.
• Do not allow to be used as a toy. Close
attention is necessary when used by or
near children.
• Do not use with a damaged cord or plug.
If vacuum cleaner is not working as it
should, has been dropped, damaged,
left outdoors, or dropped in water,
immediately discontinue use and call
1-844-608-3080 (US) / 1-844-608-3081
(CA) for assistance.
• Do not pull or carry by cord, use cord as
a handle, close a door on cord, or pull
cord around sharp edges or corners. Do
not run vacuum cleaner over cord. Keep
cord away from heated surfaces.
• Do not unplug by pulling on cord. To
unplug, grasp the plug, not the cord.
• Do not handle plug or vacuum cleaner
with wet hands.
• Do not put any objects into openings.
• Do not use with any opening blocked;
Read all instructions in this guide before assembling or using your vacuum cleaner.
keep free of dust, lint, hair, and anything
that may reduce air flow.
• Keep hair, loose clothing, fingers, and all
parts of body away from openings and
moving parts.
• Turn off all controls before unplugging.
• Use extra care when cleaning on stairs.
• Do not put on chairs, tables, etc. Keep on
floor.
• Do not use vacuum cleaner to pick
up flammable or combustible liquids
(gasoline, cleaning fluid, perfumes,
etc.), or use in areas where they may be
present. The fumes from these substances
can create a fire hazard or explosion.
• Do not pick up anything that is burning or
smoking, such as cigarettes, matches, or
hot ashes.
• Do not use vacuum cleaner without dust
cup and/or filters in place.
• Always replace the dust bag after
vacuuming carpet cleaners or freshener,
powders, and fine dust. These products
clog the filters, reduce airflow and can
cause damage to the vacuum cleaner.
Failure to replace the dust bag could
cause permanent damage to the vacuum
cleaner.
• Do not use the vacuum cleaner to pick
up sharp hard objects, small toys, pins,
paper clips, etc. They may damage the
vacuum cleaner or dust bag.
• You are responsible for making sure
that your vacuum cleaner is not used by
anyone unable to operate it properly.
- 4 -
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Proper assembly and safe use of your vacuum cleaner are your responsibilities. Your vacuum
cleaner is intended for Household use. Read this Use & Care Guide carefully for important
use and safety information. This guide contains safety statements under warning and caution
symbols.
- 5 -
VACUUM CLEANER WARRANTY
LIMITED WARRANTY
FOR FIVE YEARS from the date of sale this product is warranted against defects in
material or workmanship.
WITH PROOF OF SALE a defective product will be replaced free of charge.
The Kenmore brand is used under license. Direct all claims for warranty service to: 1-844-
608-3080 (US) / 1-844-608-3081 (CA).
This warranty does not cover filters or belts, which are expendable parts that can wear
out from normal use within the warranty period.
This warranty is void if this product is ever used for other than private household purposes.
This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
Cleva North America, Inc., Greenville SC 29607
- 6 -
PARTS AND FEATURES
It is important to know your vacuum cleaner’s parts and features to assure its proper and
safe use. Review these before using your vacuum cleaner.
REPLACEMENT PARTS
To order a replacement part,
call 1-844-608-3080 (US) /
1-844-608-3081 (CA).
Item Part No.(US) Part No.(CA)
Foam Filter 561060125 561060125
HEPA Media Exhaust Filter 561055118 561055118
Upholstery Tool 561055176 561055176
Crevice Tool 561065101 561065101
Dust Bag (6-pack) IB600 63296
Wand 561082107 561082107
Flexible Hose (with handle) 561082106 561082106
Deluxe Dusting Brush 561060177 561060177
Pet HandiMate®561014106 561014106
Filter Kit (HEPA Exhaust +
Foam Filter) 561060184 561060184
- 7 -
PARTS AND FEATURES
Handle Flexible
Hose
Hose
Release
Button
Wand
Release
Button
Brushroll
On/Off
Button
Bag Fill
Level
Indicator Lift Up
Button Wand
Suction
Control
Deluxe
Dusting
Brush
Pet HandiMate®
On/Off
Button Accessory
Storage
Connection
Hose
Handle
Release
Button
Carrying
Handle
Dust Bag
Chamber
Cover
Release
Dust Bag
Chamber
Cover (Dust
Bag Inside)
Exhaust Filter
Cover (HEPA
Media Exhaust
Filter Inside)
Motorized Nozzle
Brushroll
Indicator
Light
Lower
Cord
Hook
Power
Cord
Upper
Cord
Hook
Upholstery Tool
Crevice
Tool
Headlight
Dust Bag
(x 5)
- 8 -
Body
Handle
Wand
Nozzle
Upper
Slot
Protrusion
I
Protrusion
II
Lower
Slot
1. To place the body onto the nozzle, carry
the body over the nozzle and align the
nozzle neck with the guides in the body
and slowly drop into place until a ‘click’
is heard.
2. Insert the handle into wand until you
hear a ‘click’.
3. Locate the wand parallel with the body;
make sure the protrusion is under upper
slot as shown. Then push the wand to
fit the body and then insert downward
into the nozzle neck. Make sure the
protrusion I is locked into upper slot
and protrusion II into lower slot. A ‘click’
can be heard once you finish the wand
assembly.
Before assembling the vacuum cleaner, check the PACKING LIST (page 2). Use this list to
verify that you have received all the components of your new Kenmore Intuition® Bagged
Upright Vacuum Cleaner.
Please pay special attention to these hazard alert boxes, and follow any
instructions given. WARNING statements alert you to such hazards as fire,
electric shock, burns and personal injury. CAUTION statements alert you to
such hazards as personal injury and/or property damage.
ASSEMBLY INSTRUCTIONS
6. Lock power cord plug onto the power
cord.
4. Insert the hose into body until you hear
a ‘click’.
- 9 -
NOTE: DO NOT tilt the wand to insert it
into the nozzle neck.
DO NOT insert the wand before placing
the body onto the nozzle.
WARNING
Electrical Shock and Personal Injury
Hazard.
Wrapping the cord too tightly with
excessive stress on the cord may cause
cord damage. A damaged cord is an
electrical shock hazard and could cause
personal injury or damage.
ASSEMBLY INSTRUCTIONS
5. Make sure the upper and lower cord
hooks are in the proper position as
shown. Wrap the power cord loosely
around the upper and lower cord hooks.
Power Cord
Plug
Power Cord
Body
Upper
Cord
Hook
Lower
Cord
Hook
NOTE: Make sure to wrap the power
cord around the upper cord hook first, and
then around the lower cord hook to avoid
damaging the power cord.
1. Turn the upper cord hook to either side
and down to release the power cord.
- 10 -
CAUTION
Moving parts! To reduce the risk of personal injury, DO
NOT touch the brushroll when vacuum is on. Contacting the
brushroll while it is rotating can cut, bruise or cause other
injuries. Always turn off after operation. Use caution when
operating near children or pets.
OPERATING INSTRUCTIONS
POWER CORD – RELEASE & USE
Upper Cord
Hook
Upper
Locking
Notch
WARNING
To reduce the risk of electric shock, this
appliance has a polarized plug (one
blade is wider than the other). This plug
will fit in a polarized outlet only one
way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does
not fit, contact a qualified electrician to
install the proper outlet. Do not change
the plug in any way.
2. Detach the power cord plug from the
power cord.
3. Be sure the power cord is locked into
the upper locking notch as shown. This
will help manage the power cord when
operating the vacuum cleaner.
4. Plug the power cord plug into an outlet
located near the floor.
UPRIGHT MODE
NOTE: Make sure the vacuum cleaner
is completely assembled. Do not operate
vacuum cleaner without dust bag in place.
1. Release the handle by placing foot on
the nozzle and pull back to change
handle position.
2. Turn on the vacuum cleaner by pressing
the On/Off button for cleaning bare
floor.
NOTE: Your vacuum cleaner has two
cleaning modes: one dedicated for bare
floor and one for carpets. The vacuum
turns on in carpet cleaning mode, which
means the brushroll is spinning. To switch to
bare floor mode, simply press the Brushroll
On/Off button to turn the brushroll off.
We do not recommend vacuuming with the
brushroll on when cleaning bare floors as
this may damage your floor.
- 11 -
POWER CORD - RELEASE & USE
OPERATION MODES
WARNING
Electrical Shock and Personal Injury
Hazard
Wrapping the cord too tightly puts stress
on the cord and can cause cord damage.
A damaged cord is an electrical shock
hazard and could cause personal injury
or damage.
5. Press the On/Off button to turn the
vacuum cleaner on.
6. Once you have completed vacuuming,
press the On/Off button; unplug the
power cord plug from the outlet.
7. To restore power cord after use, turn
upper cord hook to the upright position.
Then wrap cord loosely around cord
hooks.
On/Off
Button
WARNING
Personal Injury and Product Damage
Hazard
· When any abnormality/failure occurs,
stop using the product immediately and
disconnect the power plug.
· DO NOT use outlets above counters.
Damage from cord to items in
surrounding area could occur.
BRUSHROLL STATUS INDICATOR
NOTE: The brushroll rotates when the
vacuum cleaner is in this position.
NOTE: Brushroll does not rotate in
either mode when handle is in fully upright
position.
3. Press the Brushroll On/Off button for
cleaning carpets.
4. Once the vacuum is on, operate the
vacuum cleaner by tilting the wand back
towards you and the nozzle is flush with
floor surface.
5. Once you have completed vacuuming,
press the On/Off button again and
unplug the power cord from the power
outlet.
NOTE: If the brushroll is turned on, first
press the Brushroll On/Off button to stop
the brushroll, and then press the On/Off
button to turn off the vacuum.
BAG FILL LEVEL INDICATOR
As the dust bag fills with dirt and debris,
an indicator near the wand can be used
to estimate the level of bag fill. Once all
LEDs are illuminated red, the bag should
be replaced. See page 19-20 for the dust
bag replacement instructions.
- 12 -
CAUTION
Do not allow the vacuum cleaner to
remain in one spot for any length of time
when the brushroll is turning. Damage
to carpet may occur.
CAUTION
Make sure the dust bag is replaced
when all LED lights begin to illuminate
red continuously. If not, the LED lights
will flash red. If the red flashing remains
after replacing the dust bag, check and
clean the air path as it is blocked.
OPERATION MODES
Bag Fill Level
Indicator
Bag Fill Level
One LED light (furthest
left), green continuous Lights progressively
illuminate to show
the bag is filling.
Replace the bag
when all LED lights
begin to illuminate red
continuously.
Two LED lights, orange
continuous
Three LED lights,
orange continuous
Four LED lights, red
continuous
Brushroll Status
Indicator
Status
Green LED Lights The brushroll is spinning and
working as it should.
Red LED Lights
There is a jam in the
brushroll area. Turn off and
unplug the vacuum, and
remove any blockages in
the nozzle.
No LED Lights The brushroll is off.
Brushroll
On/Off
Button
Brushroll
Status
Indicator
ABOVE FLOOR MODE
1. Place the vacuum cleaner in the upright
locked position.
2. Press the wand release button and lift up
the wand for above floor cleaning.
3. Choose the desired attachments and
insert it into the wand.
4. Turn on the vacuum cleaner by pressing
the On/Off Button.
5. Once you have completed vacuuming,
press the On/Off button again and
unplug the power cord from the power
outlet.
NOTE: The attachments also can insert
directly into the handle for above floor
cleaning.
LIFT UP MODE
1. Place the vacuum cleaner in the upright
locked position.
2. Press lift-up button and lift up the body
for portable carry.
3. Press the wand release button and lift
up the wand for cleaning stairs or other
hard to reach places.
NOTE: Make sure the power cord is
released from the cord hooks before lifting
up the wand.
- 13 -
CAUTION
When using attachments, be careful not
to over extend the stretch hose when
reaching. Trying to reach beyond the
hose stretch capability could cause the
vacuum cleaner to tip over.
CAUTION
DO NOT pull the vacuum cleaner
around the room by the hose. Property
damage or personal injury could result.
Wand
Release
Button
Lift-Up Button
Wand
Release
Button
Wand
Handle
Upholstery Tool
Upholstery Tool
OPERATION MODES
4. Choose the desired attachments and
insert it into the wand.
5. Turn on the vacuum cleaner by pressing
the On/Off Button.
6. Once you have completed vacuuming,
press the On/Off button again and
unplug the power cord from the power
outlet.
NOTE: The attachments also can insert
directly into the handle.
- 14 -
OPERATION MODES
CAUTION
When using attachments, be careful not
to over extend the stretch hose when
reaching. Trying to reach beyond the
hose stretch capability could cause the
vacuum cleaner to tip over.
CAUTION
DO NOT pull the vacuum cleaner
around the room by the hose. Property
damage or personal injury could result.
All included accessory tools can be
inserted into either the handle or the wand.
DELUXE DUSTING BRUSH
Slide the collar of the brush into the open
end of the hose or wand.
Use deluxe dusting brush for cleaning loose
surfaces such as drapes, furniture or walls.
See ATTACHMENT USE TABLE (page 16).
UPHOLSTERY TOOL
The upholstery tool can be attached to the
end of the handle and the wand. Slide the
collar of the tool into the open end of the
handle or wand.
Use the upholstery tool for cleaning
upholstery and fabric surfaces such as
sofas and drapes. See ATTACHMENT USE
TABLE (page 16).
CREVICE TOOL
Slide the collar of the crevice tool into the
open end of the hose or wand.
Use crevice tool for cleaning in tight
spaces such as furniture, between cushions,
and stairs. See ATTACHMENT USE TABLE
(page 16).
PET HANDIMATE®
The Pet HandiMate® can be attached to
the end of the handle and the wand.
Pet HandiMate® pivots for more convenient
cleaning.
Use Pet HandiMate® for cleaning fabric
surfaces such as furniture and carpet. See
ATTACHMENT USE TABLE (page 16).
- 15 -
ATTACHMENTS
CAUTION
Use attachments when the vacuum
cleaner is upright.
*Always clean attachments before using on fabrics.
BY-PASS VALVE
This vacuum cleaner has a By-Pass Valve
which prevents motor overheating and
damage. The valve opens to provide
cooling air when a clog prevents normal
air flow to the vacuum cleaner suction
motor. You will notice a change of sound
as air rushes through the valve opening.
To correct the problem: remove any clogs,
check and replace filters if needed, check
and install new dust bag if needed.
NOTE: The By-Pass Valve may open
when using attachments or when cleaning
new carpet due to reduced airflow or air
path is blocked, caused by the attachments
themselves or by new carpet lint filling the
dust bag quickly.
PERFORMANCE/SAFETY FEATURES
THERMAL PROTECTOR
This vacuum cleaner has a thermal
protector which automatically trips to
protect the vacuum cleaner suction motor.
If a clog prevents the normal flow of air to
the motor, the thermal protector turns the
motor off automatically. This allows the
motor to cool in order to prevent possible
damage to the vacuum cleaner.
To reset thermal protector: Turn the
vacuum cleaner off and unplug the power
cord from the outlet to allow the vacuum
cleaner to cool and the thermal protectors
to reset.
CAUTION
Always return the vacuum cleaner to
the upright position before using the
hose and attachments. Failure to do
so may result in overheating of the
brushroll motor and can cause the
thermal protectors to trip.
Check for and remove clogs, and replace
dust bag if necessary. Also check
and clean any clogged filters. Wait
approximately 50 minutes before restarting
vacuum cleaner.
- 16 -
ATTACHMENT USE TABLE
= Applicable
ATTACHMENT
DELUXE DUSTING BRUSH
UPHOLSTERY TOOL
CREVICE TOOL
PET HANDIMATE
®
Between
Furniture* Cushions* Drapes* Stairs Baseboards
Carpet Bare
CLEANING AREA
BRUSHROLL RESET
The brushroll has built-in protection against
motor damage should the brushroll jam.
If the brushroll slows down or stops, the
brushroll overload protector shuts off the
brushroll motor and the brushroll status
indicator emits red light. The vacuum
cleaner suction motor will continue to run.
PERFORMANCE/SAFETY FEATURES
HAIR ELIMINATORBRUSHROLL
For best performance, the motorized
nozzle is equipped with a hair eliminator
brushroll, which prevents build up of hair,
string and other debris on the brushroll.
To remove any hair wrapped around the
brushroll, simply continue vacuuming
allowing the brushroll to automatically
remove the hair wrap and send it to the
dust bag. SUCTION CONTROL
To assist with push/pull force of the
vacuum on surfaces like thick carpet, the
suction control valve can be opened to
help reduce suction. Note that for best
cleaning results, the suction control valve
must be fully closed.
· Slide to right to open the suction control
and decrease suction. Opening control
decreases suction for draperies and
lightweight rugs.
· Slide to left to close the suction control
and increase suction. Closing control
increases suction for upholstery and
carpets.
To solve the problem: Turn off and unplug
vacuum cleaner, remove obstruction, then
turn on the vacuum cleaner.
NOTE: Once the brushroll motor shuts
down, clear jam from brushroll and then
restart the vacuum cleaner. If the problem
persists, contact the vacuum cleaner help
line for assistance.
CAUTION
Moving parts! To reduce the risk of
personal injury, DO NOT touch the
brushroll when vacuum is on. Contacting
the brushroll while it is rotating can cut,
bruise or cause other injuries.
- 17 -
Brushroll Status
Indicator
Decrease Suction Increase Suction
1. Turn off and unplug vacuum cleaner. DO
NOT drip water on vacuum cleaner.
2. To clean exterior, or to reduce static
electricity and dust build-up, wipe outer
surface with a clean, soft cloth that has
been dipped in a solution of mild liquid
detergent and water, then wrung dry.
Wipe dry after cleaning.
NOTE: Wash attachments in warm
soapy water, rinse and air dry. Do not
clean in dishwasher.
1. Place the flexible hose and attachments
in storage position if necessary (see
page 8 & 9).
2. Gather the cord and wrap it loosely
around the upper and lower cord hooks.
Lock plug retainer onto the power cord.
See page 9.
3. Store the vacuum cleaner in a dry,
indoor area, on the floor with the handle
locked in the upright position.
- 18 -
Always follow all safety precautions when performing maintenance to the vacuum cleaner.
VACUUM MAINTENANCE AND CARE
WARNING
Electrical Shock and Personal Injury
Hazard
Disconnect electrical supply before
servicing or cleaning the vacuum
cleaner. Failure to do so could result in
electrical shock or personal injury from
vacuum cleaner suddenly starting.
CLEANING EXTERIOR AND ATTACHMENTS
VACUUM CLEANER STORAGE
CAUTION
Do not use attachments if they are wet.
Attachments used in dirty areas, such as
under a refrigerator, should not be used
on other surfaces until they are washed.
They could leave marks.
WARNING
Electrical Shock and Personal Injury
Hazard
Wrapping the cord too tightly puts stress
on the cord and can cause cord damage.
A damaged cord is an electrical shock
hazard and could cause personal injury
or damage.
WARNING
The motorized nozzle is equipped with
sharp comb teeth inside. DO NOT touch
comb teeth when servicing or cleaning
the vacuum, or it may cause personal
injury.
1. Pull bag chamber cover release handle
out and up, hold the cover using the
handle.
3. To install a new dust bag, insert the dust
bag collar into bracket until you hear
a ‘click’, and then rotate bracket down
until another ‘click’ can be heard. Tuck
the bag into the dust bag chamber. Be
sure all sides of the dust bag are flat
within the bag chamber.
NOTE: Do not press the dust bag
release button when release bag chamber
cover, or the dust bag will drop down
automatically.
2. Tilt the bag chamber as shown. Press
Dust Bag Release button and the dust
bag drops down automatically.
- 19 -
DUST BAG REPLACEMENT
WARNING
Always unplug power cord from
electrical outlet before performing any
service on vacuum cleaner.
Dust Bag
Chamber
Cover
Release
Dust Bag
Release
Button
Bracket Dust Bag Collar
Click
Click
4. Place the tab on the dust bag chamber
cover in the slot on the vacuum cleaner.
Push the dust bag chamber cover into
place until a ‘click’ is heard.
NOTE: Make sure the dust bag is locked
into place before pushing the dust bag
chamber cover. The dust bag chamber
cover can’t be assembled successfully if
dust bag is missing or not installed into
place.
Clean the foam filter with cold water as
needed.
NOTE: When the cleaning of filters no
longer restores vacuum cleaner suction
to full power, or the filters are worn or
broken, replace the filters. To purchase
filters, call 1-844-608-3080 (US) / 1-844-
608-3081 (CA).
Regularly clean and replace the filters to
keep the vacuum's suction power optimal.
1. Remove the dust bag as outlined in the
DUST BAG REPLACEMENT section (page
19-20).
2. Remove the foam filter cover and the
foam filter.
- 20 -
WARNING
Electrical Shock Hazard
Unplug power cord from electrical
outlet. Do not operate the vacuum
cleaner without the foam filter. Be sure
the filter is dry and properly installed to
prevent motor failure and/or electrical
shock.
Slot Tab
DUST BAG REPLACEMENT
FOAM FILTER CLEANING
Foam Filter Cover Foam Filter
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84

Kenmore Intuition Mode d'emploi

Catégorie
Aspirateurs
Taper
Mode d'emploi

dans d''autres langues