GAL 18V-160 9 26 04 338 00 0
3 41 01 366 21 0 2022-10-21
English (en)
Français (fr)
Español (es)
2
Instruction Manual
Mode d'emploi
Instrucciones de uso
en
3
fr
17
es
31
3
en
en
For your safety.
Read all safety warnings and
all instructions. Failure to
follow the warnings and instructions may
result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for futur-
ereference.
Do not use this battery charger
before you have thoroughly read and
completely understood this Instruc-
tion Manual. The documents mentioned
should be kept for later use and enclosed
with the battery charger, should it be passed
on or sold.
Please also observe the relevant national
industrial safety regulations.
Special safety instructions.
This charger can be used by children
aged from 8 years and above and
persons with reduced physical, sen-
sory or mental capabilities or lack of
experience and knowledge if they
have been given supervision or ins-
truction concerning the safe use of
the charger and understand the
hazards involved. Children may not
play with the charger. Cleaning and
users maintenance may not be per-
formed by children without supervi-
sion.
Supervise children during use, clea-
ning and maintenance. This will
ensure that children do not play with
the charger.
Only charge FEIN AMPShare Li-ion
batteries or those of AMPShare part-
ners with a capacity of 2.0 Ah or
more. The battery voltage must
match the battery charging voltage
of the charger. Do not charge non-
rechargeable batteries. Otherwise
there is danger of fire and explosion.
Keep the charger away from rain or mois-
ture. The penetration of water into an elec-
trical device increases the risk of an electric
shock.
Keep the battery charger clean. Contamina-
tion can lead to danger of an electric shock.
Before each use, check the battery charger,
cable and plug. If damage is detected, do not
use the battery charger. Never open the bat-
tery charger yourself, and have repairs car-
ried out only by FEIN or an authorized FEIN
service agent. Damaged battery chargers,
cables and plugs increase the risk of an elec-
tric shock.
Do not operate the battery charger on easily
inflammable surfaces or in combustible
environments. The heating of the battery
charger during the charging process can
pose a fire hazard.
Do not cover off the ventilation slots of the
battery charger. Otherwise, the battery
charger can overheat and no longer operate
properly.
Only charge intact original FEIN
AMPShare batteries or batteries from the
AMPShare partners intended for your char-
ger. When charging incorrect, damaged,
repaired or reconditioned batteries, imita-
tions or other brands, there is danger of fire
and/or explosion.
Vapors can escape in case of damage and
improper use of the battery. Provide for
fresh air and seek medical attention in case
of complaints. The vapors can irritate the
respiratory system.
Provide for sufficient ventilation during
operation. Do not operate the battery char-
ger in enclosed cabinets or in close vicinity
to heat sources. Ambient temperatures in
excess of +45 °C can lead to malfunctions.
Do not charge non-rechargeable batteries.
Otherwise there is danger of fire and explo-
sion.
WARNING
4en
Remove the battery from the charger and
pull the mains plug when not using for
extended periods. Saving energy helps to
save the environment.
When cleaning the battery charger, pull the
mains plug out of the socket. There is dan-
ger of electric shock.
Do not rivet or screw any name-plates or
signs onto the battery charger. If the insula-
tion is damaged, protection against an elec-
tric shock will be ineffective.
Charge the battery at temperatures above
+32 °F (0 °C) and below +113 °F (+45 °C).
Store the power tool and battery at a loca-
tion where the temperature does not exceed
+120 °F (+49 °C). This is important to avoid
severe damage to the battery cells.
Never immerse the battery, power tool or
charger in liquids of any kind or allow liquid
to enter. Corrosive or conductive liquids
(e.g. sea water, industrial chemicals or prod-
ucts containing bleach, etc.) may cause a
short circuit, resulting in fire, personal injury
and property damage.
Under extreme conditions of use or temper-
ature, the battery may leak. Avoid contact
with skin and eyes. The battery liquid is
corrosive and can cause tissue burns. If the
liquid comes into contact with the skin,
wash it off immediately with soap and water.
If the liquid gets into your eyes, flush them
with water for at least 10 minutes and seek
medical attention.
Make sure the cable is positioned in such a
manner that it cannot be stepped on, tripped
over, or otherwise damaged or strained. A
damaged plug and cable may cause an elec-
tric shock or fire.
Disconnect the charger by pulling the plug
and not the cable. Do not operate the char-
ger with a damaged cable or plug; replace
immediately. A damaged plug and cable may
cause an electric shock or fire.
Do not insert the battery into the charger if
the battery housing is damaged. Using a
damaged battery may result in electric shock
or fire.
Do not disassemble or operate the charger if
it has received a heavy blow, has been
dropped, or otherwise damaged. Incorrect
assembly or damage may result in electric
shock or fire.
Do not use accessories that are not recom-
mended by Fein or sold by Fein. The use of
accessories that are not recommended may
result in electric shock or fire.
Replace the battery when a significant
decrease in operating time per charge is
observed. The battery may be close to the
end of its service life.
When the battery is not in the
power tool or charger, keep it
away from metal objects. For example, do
not place the battery in a tool box or bag
with nails, screws, wrenches, etc. in order to
protect the terminals from short circuiting.
This can lead to fires or injuries.
Do not place the battery into a fire or expose
it to high heat. The battery can explode.
Do not attempt to disassem-
ble the battery or remove pro-
truding parts from the battery terminals.
This can lead to fires or injuries. Protect
exposed terminals with thick insulating tape
prior to disposal in order to avoid short cir-
cuits.
WARNING
WARNING
5
en
Extension cable.
If the use of an extension
cable is required, its length
and conductor cross-section must be ade-
quate for the applicational case, in order to
prevent a voltage drop in the extension
cable, power loss and overheating of the
battery charger. Otherwise, the extension
cable and battery charger are liable to elec-
trical danger, and the working efficiency will
be impaired.
Recommended dimensions of extension
cords at an operating voltage of 120 V – sin-
gle-phase a. c., with only GAL 18V-160 con-
nected:
Intended use of the battery charger:
The battery charger is intended for charging
rechargeable FEIN AMPShare Li-ion batter-
ies or those of AMPShare partners.
WARNING
Max. cable length, ft Max. cable length, m
25 50 100 150 8 15 30 46
Min. conductor size
A.W.G. Min. conductor-
cross-section, mm2
18 16 16 14 6 5 5 4
6en
FCC Warning.
The manufacturer is not responsible for
radio interference caused by unauthorized
modifications to this device. Such modifica-
tions could void the user's authority to
operate the device.
This device complies with the requirements
of Part 15 of the FCC Rules & Regulations.
Operation is subject to the following two
conditions:
1) This device may not cause harmful inter-
ference, and
2) This device must accept any interference
received, including interference that may
cause undesired operation.
NOTE! This device has been tested and com-
plies with the limits for a Class B digital
devices, pursuant to Part 15 of the FCC
Rules & Regulations. These limits are
designed to provide reasonable protection
against harmful interference in a residential
installation. This device generates, uses and
can radiate radio frequency energy. If not
installed and used in accordance with the
instructions, it may cause harmful interfer-
ence to radio communications. However,
there is no guarantee that interference will
not occur in a particular installation. If this
device does cause harmful interference to
radio or television reception, which can be
determined by turning the device off and on,
the user is encouraged to try to correct the
interference by one or more of the follow-
ing measures:
–Reorient or relocate the receiving
antenna.
–Increase the separation between the
equipment and receiver.
–Connect the device to an outlet on a cir-
cuit different from that to which the
receiver is connected.
–Consult the dealer or an experienced
radio/TV technician for help.
Exposure to radio frequency (RF) signals:
The wireless device is a radio transmitter
and receiver. It has been designed and man-
ufactured not to exceed the limits for expo-
sure to radio frequency (RF) energy set by
the Canadian Department of Health (Safety
Code 6). These limits are part of compre-
hensive guidelines that set allowable levels
of RF energy for the general population.
These guidelines are based on safety stan-
dards previously established by international
standardization bodies. These standards
contain a significant safety margin designed
to ensure the safety of all persons, regard-
less of age or health.
This device and its antenna must not be
operated together with any other antenna
or transmitter.
Industry Canada.
This device complies with Industry Canada
licence-exempt RSS standard(s). Operation
is subject to the following two conditions:
(1) This device may not cause harmful inter-
ference, and
(2) this device must accept any interference
received, including interference that may
cause undesired operation of the device.
7
en
Symbols, Abbreviations and Terms Used.
Symbol, character Explanation
Make sure to read the enclosed documents such as the Instruction
Manual and the General Safety Instructions.
Before commencing this working step, pull the mains plug out of the
socket.
AMPShare is the shared battery system that allows you to use many
tools from many professional brands with just one battery.
The Rechargeable Battery Recycling Corporation (RBRC) is a
rechargeable battery take-back and recycling organization in the
U.S. and Canada.
Confirms the conformity of the battery charger with the Guidelines
of the European Community.
This symbol confirms the certification of this product for the USA
and Canada.
This sign indicates a possible dangerous situation that could cause
severe or fatal injury.
Recycling code: identifies recyclable materials
Worn out battery chargers and other electro-technical and electri-
cal products should be collected separately and sorted for environ-
ment-friendly recycling.
Product with double or reinforced insulation
Battery type
Weight according to EPTA-Procedure 01
Time-lag device fuse, whereby X represents the character for the
time/power characteristic acc. to IEC 60127.
Use the device only in rooms and do not subject it to rain.
Direct current
Dangerous voltage
Warning! Electrical voltage
WARNING
X
8en
Character Unit of measurement,
international Explanation
U1V Rated supply voltage
U2V Rated output direct voltage
(rated battery voltage)
P
1
WPower input
fHz Frequency
I
max
mA Maximum rated output direct current (max.
charging current)
C
Ah Capacity
t
min Charge duration
T
°C/°F Temperature
9
en
Technical description and specifications.
Charging compartment
Power boost button
Wall mount
Green battery charge-
control indicator
Red temperature
monitoring/
error indicator
Fig. 1
10 en
A) Dependent on temperature and battery type
B) Battery charge level 50 % (after charging with Power Boost). The battery can be removed
for immediate use.
C) Battery charge level approx. 80 % (after charging with Power Boost). The battery can be
removed for immediate use.
D) Battery charge level approx. 80 % (after charging with standard charging mode). The bat-
tery can be removed for immediate use.
E) Battery charge level approx. 97 % – 100 % (after charging with standard charging mode).
Type GAL 18V-160
Order number 9 26 04 338 00 0
Battery charging voltage (automatic voltage detection) 18 V
Charging currentA) 16.0 A
Permissible battery temperature during charging 0 °C – 45 °C
CORE18V... batteries:
Charging duration at battery capacity, approx.A) approx. 50 % B) / approx. 80 % C) /
approx. 80 % D) / Battery charged E)
–4.0 Ah 9 min / 21 min/ 32 min / 51 min
–8.0 Ah 15 min / 26 min / 32 min / 51 min
–12.0 Ah 22 min / 36 min / 36 min / 55 min
Amount of battery cells 5 – 15
Weight according to EPTA-Procedure 01 2.10 lbs
0.95 kg
Class of protection / II
11
en
Installation.
Before any work on the battery charger itself, pull the mains plug from the
socket outlet.
Wall mounting.
Use mounting material suitable for the wall
type and weight of the charger and the
heaviest battery. If the battery charger is
installed without using the proper mounting
material, the product may become unstable
and cause property damage or personal
injury.
Do not mount the battery charger at a loca-
tion on the wall where the weight of the
charger and battery cannot be supported. If
the strength of the wall mount is not suffi-
cient to support the charger and battery, the
charger may drop and cause injury.
Make sure that there are no hidden live
wires, water or gas pipes behind the mount-
ing area. Cutting or drilling into such lines
can result in serious injury or death.
Do not mount the charger the wrong way
around or upside down. Improper mounting
may result in property damage or personal
injury.
The charger can be mounted to a wall using
wall mounts.
a) Find a suitable mounting location on the
wall.
b) Mark two points on a vertical line with a
clearance of 3-25/64" (86 mm) apart.
c) Select the appropriate screws and dow-
els (if necessary) for the wall material.
(Mounting material is not included in
delivery scope.)
d) Drill into the wall using a suitable drill bit.
If dowels are to be used, follow the
dowel manufacturer's instructions.
e) Screw two round-head screws (not
included in delivery scope) with a diam-
eter of 13/64" (5 mm) to a maximum of
1/4" (6.5 mm) into the wall or dowels.
Leave an approx. 1/8" (3.3 mm) gap
between the bottom of the screw head
and the wall.
f) Position the wall mounting slots of the
charger facing against the fastening
screws. Push the charger against the wall
and slide it down to secure the charger
to the fastening screws, ensuring the
slots have engaged the screw heads.
Note: Make sure that the charger is securely
mounted and seated firmly against the wall.
Adjust the screws as required to ensure that
the charger faces flat against the wall.
WARNING
Wall mount
86 mm
Fig. 2
12 en
Starting Operation.
Observe the mains voltage! The voltage of
the power source must correspond with the
data on the type plate of the battery charger.
Charging procedure.
The charge procedure begins as soon as the
mains plug of the battery charger is plugged
into the socket outlet and the battery is
inserted into the charging compartment.
The intelligent charging process automati-
cally detects the battery's charge condition
and charges it with the optimal charging cur-
rent depending on the battery temperature
and voltage.
This saves the battery and ensures that it is
always fully charged when in the battery
charger.
Meaning of the indicators.
LED indicator Meaning
Green battery charge-control indica-
tor The 5 green LEDs indicate the charge condition of
the battery during and after the charging proce-
dure. A continuously lit LED indicates a battery
capacity of approx. 20 %.
LED condition
–The 5 LEDs light up one after the other.
(< approx. 20 % battery capacity)
–The bottom LED lights up continuously.
(approx. 20 % battery capacity)
–The 2 bottom LEDs light up continuously.
(approx. 40 % battery capacity)
–The 3 bottom LEDs light up continuously.
(approx. 60 % battery capacity)
–The 4 bottom LEDs light up continuously.
(approx. 80 % battery capacity)
–The 5 LEDs light up continuously.
(> approx. 95 % battery capacity)
Note: The charging procedure is only possible if
the temperature of the battery is within the per-
missible charging temperature range, see section
"Technical data".
Continuously lit red temperature
monitoring/error indicator The continuously lit red indicator indicates that
the temperature of the battery is not within the
allowable charging-temperature range, see section
"Technical data". As soon as the allowable charg-
ing temperature range is reached, the charging
procedure begins.
Flashing red temperature monitor-
ing/error indicator The flashing red indicator indicates that the battery
or the charger is defective.
13
en
Power boost button.
Pressing the power boost button activates
the rapid-charging mode. This can be done
before the battery is inserted or when the
battery already is inserted. The power boost
button lights up red during rapid charging.
Pressing the power boost button again
returns you to the standard charging mode.
When the rapid charging is completed
(approx. 50 % battery capacity reached), the
power boost button goes out. If the battery
remains in the charger, it will continue to be
charged.
Audio signal.
As soon as the charging cycle is completed,
a brief audio signal is emitted.
Trouble shooting - Causes and corrective action.
Cause Corrective action
Flashing red temperature monitoring/error indicator
No charging procedure possible
Battery not (correctly) inserted Insert battery correctly into charger
Battery contacts contaminated Clean battery contacts; e.g. by inserting and
removing the battery several times; replace bat-
tery if necessary
Battery defective Replace battery
Green battery charge-control indicator not lit
Mains plug of the battery charger not
(correctly) plugged in Plug mains plug (completely) into socket outlet
Socket outlet, mains cable or charger
defective Check the mains voltage; if necessary, have the
charger checked by an authorized customer ser-
vice center for FEIN power tools.
14 en
Working instructions.
A significantly reduced operating period
after charging indicates that the battery is
worn out and must be replaced.
During continuous or several successive
charging cycles without interruption, the
charger may heat up. However, this is harm-
less and does not indicate a technical defect
of the battery charger.
Battery cooling (Active Air Cooling).
The fan control integrated in the charger
monitors the temperature of the inserted
battery. As soon as the battery temperature
is above approx. 0 °C, the battery is cooled
by a fan. The switched-on fan thereby pro-
duces a ventilation noise.
If the fan does not run, it is defective or the
battery temperature is < 0 °C. This may
increase the charge duration
Charging procedure - Power boost
mode.
In power boost mode, batteries are charged
in rapid-charging mode up to approx. 50 %
battery capacity. Thus, these batteries are
ready for use again in less time than when
charging in standard charging mode.
With power boost, the battery is initially
charged with a high charging current, which
is then gradually reduced.
If the battery remains in the charger, it will
continue to be charged.
Charging procedure - Standard
charging mode.
The battery is charged to approx. 100 % bat-
tery capacity. The standard charging mode is
the best combination of fast charging dura-
tion and complete charging of the battery.
Standard charging mode optimizes battery
service life.
15
en
Maintenance and Cleaning.
Perform cleaning once a week in case of fre-
quent use. Observe the following guidelines:
–Keep the contacts in the slide-on shoe
clean.
–Only dry-clean electrical contacts.
–Ensure that metal chips do not enter the
charger housing.
When the charger's power supply cord is
damaged, it must be replaced by the manu-
facturer or their representative.
Servicing and After-Sales Service.
Always have the battery charger repaired,
maintained and inspected only by qualified
electricians, as improper repair may result in
considerable danger to the user.Renew
stickers and warning indications on the bat-
tery charger when aged and worn.For FEIN
power tools and accessories in need of
repair, please contact your FEIN after-sales
service. The address can be found on the
Internet under www.fein.com.
Warranty and liability.
The warranty for the product is valid in
accordance with the legal regulations in the
country where it is marketed. In addition,
FEIN also provides a guarantee in accor-
dance with the FEIN manufacturer’s war-
ranty declaration.
The delivery scope of your battery charger
may include only a part of the accessories
described or shown in this Instruction Man-
ual.
Environmental protection, disposal.
Packaging, worn out battery chargers and
accessories should be sorted for environ-
ment-friendly recycling.
Dispose of batteries only when discharged.
For batteries that are not completely dis-
charged, insulate the terminals with tape as a
protective measure against short-circuiting.
16 en
LITHIUM-ION BATTERIES.
If equipped with a lithium-ion battery, the
battery must be collected, recycled or dis-
posed of in an environmentally sound man-
ner. The EPA certified RBRC Battery
Recycling Seal on the lithium-ion
(Li-ion) battery indicates FEIN Tool
Corporation is voluntarily partici-
pating in an industry program to collect and
recycle these batteries at the end of their
useful life, when taken out of service in the
United States or Canada. The RBRC pro-
gram provides a convenient alterative to
placing used Li-ion batteries into the trash or
the municipal waste stream, which may be
illegal in your area.
Please call 1-8000-8-BATTERY for informa-
tion on Li-ion battery recycling and disposal
bans/restrictions in your area, or return
your batteries to a FEIN Service Center for
recycling. FEIN Tool Corporation's involve-
ment in this program is part of our commit-
ment to preserving our environment and
conserving our natural resources.
17
fr
fr
Pour votre sécurité.
Lire tous les avertisse-
ments de sécurité et
toutes les instructions. Ne pas suivre les
avertissements et instructions peut donner
lieu à une électrocution, un incendie et/ou
une blessure sérieuse.
Conservez tous les avertissements et toutes
les instructions pour pouvoir vous y reporter
ultérieurement.
Ne pas utiliser ce chargeur avant
d’avoir bien lu et complètement
compris cette notice d’utilisation.
Bien garder ces documents pour une utilisa-
tion ultérieure et les joindre au chargeur en
cas de transmission ou vente à une tierce
personne.
De même, respecter les dispositions concer-
nant la prévention des accidents du travail en
vigueur dans le pays en question.
Instructions particulières de sécurité.
Cet appareil peut être utilisé par des
enfants de 8 ans et au delà ainsi que
par des personnes disposant de capa-
cités physiques réduites et manquant
d’expérience et de connaissances à
condition que ces derniers soient
supervisées ou qu’elles aient été ins-
truites quant au maniement de
l’appareil et quant aux dangers qu’il
représente. Les enfants ne doivent
pas jouer avec l'appareil. Les enfants
ne doivent ni nettoyer ni effectuer
des travaux d’entretien sans être sur-
veillé.
Surveiller les enfants lors de l’utilisa-
tion, du nettoyage et de l’entretien.
Faire en sorte que les enfants ne jou-
ent pas avec le chargeur.
Ne charger que les batteries Li-Ion
AMPShare de FEIN ou des partenaires
AMPShare d’une capacité minimale
de 2,0 Ah. La tension des batteries
doit correspondre à la tension de
charge du chargeur. Ne pas rechar-
ger de batteries non rechargeables.
Sinon, il y a risque d’explosion et
d’incendie.
Ne pas exposer le chargeur à la pluie ou à
des conditions humides. La pénétration
d’eau dans un outil électrique augmente le
risque d’un choc électrique.
Maintenir le chargeur propre. Un encrasse-
ment augmente le risque d’un choc électri-
que.
Avant toute utilisation, contrôler le char-
geur, la fiche et le câble. Ne pas utiliser le
chargeur si des défauts sont constatés. Ne
pas ouvrir le chargeur soi-même et ne le
faire réparer que par FEIN ou un atelier
agréé FEIN. Des chargeurs, câbles et fiches
endommagés augmentent le risque d’un
choc électrique.
Ne pas utiliser le chargeur sur un sol facile-
ment inflammable ou dans un environne-
ment inflammable. L’échauffement du
chargeur lors du processus de charge aug-
mente le risque d’incendie.
Ne pas recouvrir les orifices de ventilation
du chargeur. Sinon, le chargeur peut sur-
chauffer et ne plus fonctionner correcte-
ment.
Ne charger que des batteries intactes
AMPShare de FEIN ou des batteries des par-
tenaires
AMPShare qui sont destinées à votre char-
geur. Lors du chargement de batteries d’un
type ne convenant pas à l’appareil, de batte-
ries endommagées, réparées ou modifiées,
de batteries contrefaites ou d’autres fabri-
cants, il y a danger d’incendie et / ou
d’explosion.
En cas d’endommagement et d’utilisation
non conforme de la batterie, des vapeurs
peuvent s’échapper. Bien aérer le local et
consulter un médecin en cas de malaise. Les
vapeurs peuvent irriter les voies respiratoi-
res.
AVERTISSEMENT
18 fr
Toujours veiller à une aération suffisante
pendant l’utilisation. Ne pas faire fonction-
ner le chargeur dans des armoires fermées
ou à proximité de sources de chaleur. Les
températures environnantes supérieures à
+45 °C peuvent entraîner des dysfonction-
nements.
Ne pas charger des batteries non rechargea-
bles. Sinon, il y a risque d’explosion et
d’incendie.
En cas de période assez longue de non-utili-
sation, déconnecter la batterie du chargeur
et retirer la fiche de la prise de courant. Éco-
nomiser l’énergie aide à protéger l’environ-
nement.
Lors du nettoyage, retirer la fiche de la prise
de courant. Il y a risque de choc électrique.
Il est interdit de visser ou de riveter des pla-
ques ou des repères sur le chargeur. Une
isolation endommagée ne présente aucune
protection contre un choc électrique.
Charger la batterie à des températures
supérieures à +32 °F (0 °C) et inférieures à
+113 °F (+45 °C). Stocker l’outil et la batterie
dans un endroit où la température ne dépas-
se pas +120 °F (+49 °C). Ceci est important
afin d’éviter d’endommager gravement les
cellules de la batterie.
Ne jamais immerger la batterie, l’outil ou le
chargeur dans un liquide quelconque et ne
jamais laisser y pénétrer du liquide. Les
liquides corrosifs ou conducteurs (par
exemple l’eau de mer, les produits chimi-
ques industriels ou les produits contenant
des agents de blanchissement, etc.) peuvent
provoquer un court-circuit susceptible
d’entraîner un incendie, des blessures cor-
porelles ou des dégâts matériels.
Dans des conditions d’utilisation ou de tem-
pérature extrêmes, la batterie peut fuir. Évi-
ter tout contact avec les yeux et la peau. Le
liquide de la batterie est caustique et peut
entraîner des brûlures chimiques de la peau.
Au cas où le liquide entrerait en contact avec
la peau, rincer rapidement à l’eau et au
savon. Au cas où le liquide pénètrerait dans
les yeux, rincer à l’eau claire pendant au
moins 10 minutes, puis consulter un méde-
cin.
S’assurer que le câble est placé de manière
à ce qu’il ne soit pas possible de marcher
dessus, de trébucher dessus ou de l’endom-
mager ou de le soumettre à une contrainte
quelconque. Une fiche et un câble endom-
magés peuvent provoquer un choc électri-
que ou un incendie.
Débrancher le chargeur en tirant sur la fiche
et non sur le câble. Ne pas utiliser le char-
geur si le câble ou la fiche sont
endommagés ; les remplacer immédiate-
ment. Une fiche ou un câble endommagés
peuvent provoquer un choc électrique ou
un incendie.
Ne pas insérer la batterie dans le chargeur
si le boîtier de la batterie est endommagé.
L’utilisation d’une batterie endommagée
peut entraîner un choc électrique ou un
incendie.
Ne pas démonter et ne pas mettre en fonc-
tion le chargeur s’il a subi un choc violent,
s’il est tombé ou s’il a été endommagé de
quelque manière que ce soit. Un mauvais
assemblage ou un endommagement peut
entraîner un choc électrique ou un incendie.
Ne pas utiliser d’accessoires qui ne sont pas
recommandés ou vendus par Fein. L’utilisa-
tion d’accessoires non recommandés peut
entraîner un choc électrique ou un incendie.
Remplacer la batterie si une baisse signifi-
cative de l’autonomie par charge est consta-
tée. La durée de vie de la batterie est peut-
être presque terminée.
Si la batterie n’est pas
dans l’appareil ou le
chargeur, la tenir éloignée de tout objet
métallique. Par exemple, ne pas placer la
batterie dans une boîte à outils ou un sac
contenant des clous, des vis, des clés, etc.
afin de protéger les pôles contre les courts-
circuits. Ceci peut entraîner des incendies
ou de graves blessures.
Ne pas jeter la batterie au feu et ne pas
l’exposer à une forte source de chaleur. La
batterie peut exploser.
AVERTISSEMENT
19
fr
Ne pas essayer de
démonter la batterie
ou de retirer les pièces saillantes des pôles
de la batterie. Ceci peut entraîner des incen-
dies ou de graves blessures. Avant l’élimina-
tion, protéger les pôles exposés avec du
ruban isolant épais afin d’éviter les courts-
circuits.
Câble de rallonge.
Au cas où une rallonge
serait nécessaire, la
longueur ainsi que la section du conducteur
de celle-ci doivent être appropriées à l’utili-
sation afin d’éviter une baisse de tension
dans la rallonge, une perte de puissance et
une surchauffe du chargeur. Sinon la ral-
longe et le chargeur présentent des dangers
électriques et l’efficacité du travail est entra-
vée.
Dimensions recommandées pour câbles de
rallonge pour une tension de service de
120 V courant alternatif monophasé si seu-
lement GAL 18V-160 est connecté :
Utilisation du chargeur :
Le chargeur est destiné à charger les batte-
ries rechargeables FEIN AMPShare Li-Ion ou
celles des partenaires AMPShare.
AVERTISSEMENT
AVERTISSEMENT
Longueur du câble
enpieds Longueur du câble
enm
25 50 100 150 8 15 30 46
Dimension min. du
conducteur en for-
mat américain
(A.W.G.)
Section min. du
conducteur, mm2
18 16 16 14 6 5 5 4
20 fr
Avertissement FCC.
Le fabricant n’est pas responsable des inter-
férences radio provoquées par des modifica-
tions non autorisées de cet appareil. De
telles modifications peuvent entraîner la
perte de l’autorisation de l’utilisateur à utili-
ser l’appareil.
Cet appareil est conforme à la partie 15 des
règles de la FCC. Le fonctionnement est
soumis aux deux conditions suivantes :
1) cet appareil ne doit pas provoquer
d’interférences nuisibles, et
2) cet appareil doit accepter toute interfé-
rence reçue, y compris les interférences qui
peuvent provoquer un fonctionnement
indésirable.
REMARQUE ! Cet appareil a été testé et décla-
ré conforme aux limites imposées aux appa-
reils numériques de classe B, conformément
à la partie 15 des règles de la FCC. Ces limi-
tes sont conçues pour fournir une protec-
tion raisonnable contre les interférences
nuisibles en cas d’installation dans une zone
résidentielle. Cet appareil génère, utilise et
peut émettre de l’énergie de fréquence
radio. S'il n’est pas installé et utilisé confor-
mément aux instructions, il peut provoquer
des interférences nuisibles aux communica-
tions radio. Il n’est toutefois pas possible de
garantir l’absence d’interférences pour une
installation donnée. Si cet appareil provoque
des interférences nuisibles à la réception de
la radio ou de la télévision, ce qui peut être
déterminé en allumant et en éteignant
l’appareil, l’utilisateur est invité à essayer de
corriger ces interférences en prenant une ou
plusieurs des mesures suivantes :
–Réorienter ou déplacer l’antenne de
réception.
–Augmenter la distance entre l’appareil et
le récepteur.
–Brancher l’appareil sur une prise d’un cir-
cuit différent de celui sur lequel le récep-
teur est branché.
–Contacter le revendeur ou un technicien
radio / télé expérimenté pour obtenir de
l’aide.
Exposition à des signaux de fréquence radio
(RF) : L’appareil sans fil est un émetteur-
récepteur radio. Il a été conçu et fabriqué de
manière à ne pas dépasser les limites
d’exposition à l’énergie de fréquence radio
(RF) fixées par le ministère canadien de la
Santé (Safety Code 6). Ces limites font par-
tie de directives globales qui définissent les
niveaux d’énergie RF admissibles pour la
population générale.
Ces directives sont basées sur les normes de
sécurité préalablement établies par les orga-
nismes internationaux de normalisation. Ces
normes comportent une marge de sécurité
importante qui vise à garantir la sécurité de
toutes les personnes, quel que soit leur âge
ou leur état de santé.
Cet appareil et son antenne ne doivent pas
être utilisés conjointement avec une autre
antenne ou un autre émetteur.
Industrie Canada.
Cet appareil est conforme à la (aux)
norme(s) RSS libre(s) de droits d’Industrie
Canada. Le fonctionnement est soumis aux
deux conditions suivantes :
(1) cet appareil ne doit pas provoquer
d’interférences, et
(2) cet appareil doit accepter toute interfé-
rence, y compris les interférences suscepti-
bles de provoquer un fonctionnement non
souhaité de l’appareil.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
FEIN Battery starter set CORE 18 V 12.0 Ah AMPShare Manuel utilisateur
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
Documents connexes
Autres documents
-
Bosch 9173758 Le manuel du propriétaire
-
SCANGRIP 03.5701C Powerful Diffused Light Head Providing Manuel utilisateur
-
-
-
-
Sony Série Cyber Shot DSC-W560 Manuel utilisateur
