FEIN ASW 18-6 PC Manuel utilisateur

USA

FEIN Power Tools, Inc.

1000 Omega Drive

Suite 1180

Pittsburgh, PA 15205

Phone: 800-441-9878

www.feinus.com

Canada

FEIN Canadian Power Tool

Company

323 Traders Boulevard East

Mississauga, Ontario L4Z 2E5

Telephone: (905) 8901390

Phone: 1-800-265-2581

www.fein.com

FEIN Service USA

FEIN Power Tools, Inc.

2735 Hickory Grove Road

Davenport, IA 52804

Phone: 800-441-9878

magdrillrepair@feinus.com

Headquarter

C. & E. FEIN GmbH

Hans-Fein-Straße 81

D-73529 Schwäbisch Gmünd-Bargau

www.fein.com

 ASW18-6 (**) 7 112 ...

 ASW18-12 (**) 7 112 ...

 ASW18-18 (**) 7 112 ...

 ASW18-6 PC (**) 7 112 ...

 ASW18-12 PC (**) 7 112 ...

 ASW18-18 PC (**) 7 112 ...

 ASW18-30 PC (**) 7 112 ...

 ASW18-45 PC (**) 7 112 ...

 ASW18-60 PC (**) 7 112 ...

OBJ_DOKU-0000006443-002.fm Page 1 Friday, July 14, 2017 9:43 AM

2

Instruction Manual

Mode d’emploi

Instrucciones de uso

en

3

fr

26

es

50

OBJ_BUCH-0000000252-002.book Page 2 Friday, July 14, 2017 9:34 AM

3

en

For your safety.

Read all safety warnings and

all instructions. Failure to fol-

low the warnings and instructions may result

in electric shock, fire and/or serious injury.

Save all warnings and instructions for future-

reference.

Do not use this power tool before you

have thoroughly read and completely

understood this Instruction Manual, including

the figures, specifications, safety regulations

and the signs indicating DANGER, WARN-

ING and CAUTION.

Only carry out such operations with this

power tool as intended for by FEIN. Only use

application tools and accessories that have

been released by FEIN.

Please also observe the relevant national

industrial safety regulations.

Non-observance of the safety instructions in

the said documentation can lead to an electric

shock, burns and/or severe injuries.

This Instruction Manual should be kept for

later use and enclosed with the power tool,

should it be passed on or sold.

SAVE THESE INSTRUCTIONS.

The term “power tool” in the warnings refers

to your mains-operated (corded) power tool

or battery operated (cordless) power tool.

General safety rules.

1) Work area safety

a)Keep work area clean and well lit. Clut-

tered or dark areas invite accidents.

b)Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power

tools create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders away

while operating a power tool. Distrac-

tion can cause you to lose control.

2) Electrical safety

a)Power tool plugs must match the outlet.

Never modify the plug in any way. Do not

use any adapter plugs with earthed

(grounded) power tools. Unmodified

plugs and matching outlets will reduce

risk of electric shock.

b)Avoid body contact with earthed or

grounded surfaces such as pipes, radia-

tors, ranges and refrigerators. There is

an increased risk of electric shock if

your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power

tool will increase the risk of electric

shock.

d)Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging

the power tool. Keep cord away from

heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase

the risk of electric shock.

e) When operating a power tool outdoors,

use an extension cord suitable for out-

door use. Use of a cord suitable for out-

door use reduces the risk of electric

shock.

f) If operating a power tool in a damp loca-

tion is unavoidable, use a ground fault

circuit interrupter (GFCI) protected sup-

ply. Use of an GFCI reduces the risk of

electric shock.

3) Personal safety

a)Stay alert, watch what you are doing

and use common sense when operating

a power tool. Do not use a power tool

while you are tired or under the influ-

ence of drugs, alcohol or medication. A

moment of inattention while operating

power tools may result in serious per-

sonal injury.

b)Use personal protective equipment.

Always wear eye protection. Protective

equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing pro-

tection used for appropriate conditions

will reduce personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the off-position before

connecting to power source and/or bat-

tery pack, picking up or carrying the

tool. Carrying power tools with your

finger on the switch or energising

power tools that have the switch on

invites accidents.

d)Remove any adjusting key or wrench

before turning the power tool on. A

wrench or a key left attached to a rotat-

ing part of the power tool may result in

personal injury.

WARNING

OBJ_BUCH-0000000252-002.book Page 3 Friday, July 14, 2017 9:34 AM

4

en

e) Do not overreach. Keep proper footing

and balance at all times. This enables

better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose cloth-

ing or jewelery. Keep your hair, clothing

and gloves away from moving parts.

Loose clothes, jewelry or long hair can

be caught in moving parts.

g)If devices are provided for the connec-

tion of dust extraction and collection

facilities, ensure these are connected

and properly used. Use of dust collec-

tion can reduce dust-related hazards.

4) Power tool use and care

a)Do not force the power tool. Use the cor-

rect power tool for your application. The

correct power tool will do the job bet-

ter and safer at the rate for which it was

designed.

b)Do not use the power tool if the switch

does not turn it on and off. Any power

tool that cannot be controlled with the

switch is dangerous and must be

repaired.

c) Disconnect the plug from the power

source and/or the battery pack from the

power tool before making any adjust-

ments, changing accessories, or storing

power tools. Such preventive safety

measures reduce the risk of starting the

power tool accidentally.

d)Store idle power tools out of the reach of

children and do not allow persons unfa-

miliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the hands

of untrained users.

e) Maintain power tools. Check for mis-

alignment or binding of moving parts,

breakage of parts and any other condi-

tion that may affect the power tool’s

operation. If damaged, have the power

tool repaired before use. Many accidents

are caused by poorly maintained power

tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with

sharp cutting edges are less likely to

bind and are easier to control.

g)Use the power tool, accessories and tool

bits etc. in accordance with these

instructions, taking into account the

working conditions and the work to be

performed. Use of the power tool for

operations different from those

intended could result in a hazardous sit-

uation.

5) Battery tool use and care

a)Recharge only with the charger speci-

fied by the manufacturer. A charger that

is suitable for one type of battery pack

may create a risk of fire when used with

another battery pack.

b)Use power tools only with specifically

designated battery packs. Use of any

other battery packs may create a risk of

injury and fire.

c) When battery pack is not in use, keep it

away from other metal objects, like

paper clips, coins, keys, nails, screws or

other small metal objects, that can

make a connection from one terminal to

another. Shorting the battery terminals

together may cause burns or a fire.

d)Under abusive conditions, liquid may be

ejected from the battery; avoid contact.

If contact accidentally occurs, flush

with water. If liquid contacts eyes, addi-

tionally seek medical help. Liquid

ejected from the battery may cause irri-

tation or burns.

6) Service

a)Have your power tool serviced by a qual-

ified repair person using only identical

replacement parts. This will ensure that

the safety of the power tool is main-

tained.

OBJ_BUCH-0000000252-002.book Page 4 Friday, July 14, 2017 9:34 AM

5

en

Special safety instructions.

Hold power tool by insulated gripping sur-

faces, when performing an operation where

the fastener may contact hidden wiring. Fas-

teners contacting a “live” wire may make

exposed metal parts of the power tool “live”

and could give the operator an electric shock.

Beware of any concealed electric cables, gas

or water conduits. Check the working area

before commencing work, e. g. with a metal

detector.

Secure the work piece firmly. A work piece

that is gripped tightly in a clamping device or

vice, is more secure than if held by hand.

Hold the power tool firmly. High reaction

torque can briefly occur.

Do not machine any material containing

asbestos. Asbestos is cancerogenic.

Do not rivet or screw any name-plates or

signs onto the power tool. If the insulation is

damaged, protection against an electric shock

will be ineffective. Adhesive labels are recom-

mended.

Do not use accessories which are not specifi-

cally designed and recommended by the

power tool manufacturer. Safe operation is

not ensured merely because an accessory fits

your power tool.

Clean the ventilation openings on the power

tool at regular intervals using non-metal

tools. The blower of the motor draws dust

into the housing. An excessive accumulation

of metallic dust can cause an electrical hazard.

Never look or stare into the light of the power

tool's lamp from a short distance. Never point

the light of the lamp into the eyes of other

persons in close vicinity. The radiation pro-

duced by the lamp can be harmful for the eye.

Do not direct the power tool against yourself,

other persons or animals. Danger of injury

from sharp or hot application tools.

Use and handling of the battery (bat-

tery pack)

To avoid hazardous situations such as burns,

fire, explosion, skin injuries, and other inju-

ries when handling the battery, observe the

following instructions:

Batteries must not be disassembled, opened

or reduced in size. Do not subject batteries to

mechanical impact or shock. Hazardous

vapours and fluid can escape in case of dam-

age and improper use of the battery. The

vapours can irritate the respiratory system.

Liquid ejected from the battery may cause

skin irritations or burns.

When battery fluid from a damaged battery

has come into contact with objects close by,

check the respective components, clean them

or replace them as required.

Keep the battery away from heat and fire. Do

not store the battery in direct sunlight.

Do not remove the battery from its original

packaging until it is going to be used.

Before any work on the machine itself,

remove the battery from the power tool. If the

power tool accidentally starts, there is danger

of injury.

Remove the battery only when the power tool

is switched off.

Keep the battery away from children.

Keep the battery clean and protect it against

moisture and water. Clean contaminated bat-

tery terminals and power tool connections

with a dry, clean cloth.

Use only intact original FEIN batteries that are

intended for your power tool. When working

with and charging incorrect, damaged,

repaired or reconditioned batteries, imita-

tions or other brands, there is danger of fire

and/or explosion.

Follow the safety warnings in the operating

instructions of the battery charger.

OBJ_BUCH-0000000252-002.book Page 5 Friday, July 14, 2017 9:34 AM

6

en

Hand/arm vibrations.

While working with this power

tool, hand/arm vibrations

occur. These can lead to health impairments.

The vibration emission value

during actual use of the power

tool can differ from the declared value

depending on the ways in which the tool is

used.

It is necessary to identify

safety measures to protect the

operator that are based on an estimation of

exposure in the actual conditions of use.

The vibration emission level given in this

information sheet has been measured in

accordance with a standardised test given in

EN 60745 and may be used to compare one

tool with another. It may be used for a pre-

liminary assessment of exposure.

The declared vibration emission level repre-

sents the main applications of the tool. How-

ever if the tool is used for different

applications, with different accessories or

poorly maintained, the vibration emission

may differ. This may significantly increase the

exposure level over the total working period.

An estimation of the level of exposure to

vibration should also take into account the

times when the tool is switched off or when

it is running but not actually doing the job.

This may significantly reduce the exposure

level over the total working period.

Identify additional safety measures to protect

the operator from the effects of vibration

such as: maintain the tool and the accessories,

keep the hands warm, organisation of work

patterns.

Emission values for sound and vibration (Two-figure – specifications as per ISO 4871)

WARNING

Sound emission ASW18-30PC (**) ASW18-45PC (**) ASW18-60PC (**)

A-weighted emission pressure

power level measured at the

workplace

L

pA

(re 20 μPa), in

decibels < 81 < 81 < 81

Measuring uncertainty

K

pA

, in

decibels 3 3 3

Measured A-weighted sound

power level

L

wA

(re 1 pW), in

decibels < 92 < 92 < 92

Measuring uncertainty

K

wA

, in

decibels 3 3 3

C-weighted peak sound pressure

level measured at the workplace

L

pCpeak

, in decibels < 95 < 95 < 95

Measuring uncertainty

K

pCpeak

, in

decibels 3 3 3

Vibrations

Weighted acceleration, in

– m/s

2

– ft/s

2

< 1.8

< 6.0

< 1.8

< 6.0

< 1.8

< 6.0

Measuring uncertainty

K

, in

– m/s

2

– ft/s

2

1.5

5.0

1.5

5.0

1.5

5.0

REMARK: The sum of the measured emission value and respective measuring inaccuracy rep-

resents the upper limit of the values that can occur during measuring.

Wear hearing protection!

Measured values determined in accordance with the corresponding product standard.

OBJ_BUCH-0000000252-002.book Page 6 Friday, July 14, 2017 9:34 AM

7

en

Intended use of the power tool:

Hand-held screwdriver for screwing in and unscrewing screws and nuts in weather-protected

environments without water supply using the application tools and accessories recommended

by FEIN.

Sound emission ASW18-6

(**)

ASW18-12

(**)

ASW18-18

(**)

ASW18-

6PC (**)

ASW18-

12PC (**)

ASW18-

18PC (**)

A-weighted emission

pressure power level

measured at the

workplace

L

pA

(re 20

μPa), in decibels < 81 < 81 < 81 < 81 < 81 < 81

Measuring uncer-

tainty

K

pA

, in decibels 3 3 3 3 3 3

Measured A-

weighted sound

power level

L

wA

(re 1

pW), in decibels < 92 < 92 < 92 < 92 < 92 < 92

Measuring uncer-

tainty

K

wA

, in deci-

bels 333333

C-weighted peak

sound pressure level

measured at the

workplace

L

pCpeak

, in

decibels < 95 < 95 < 95 < 95 < 95 < 95

Measuring uncer-

tainty

K

pCpeak

, in

decibels 333333

Vibrations

Weighted accelera-

tion, in

– m/s

2

– ft/s

2

< 1.8

< 6.0

< 1.8

< 6.0

< 1.8

< 6.0

< 1.8

< 6.0

< 1.8

< 6.0

< 1.8

< 6.0

Measuring uncer-

tainty

K

, in

– m/s

2

– ft/s

2

1.5

5.0

1.5

5.0

1.5

5.0

1.5

5.0

1.5

5.0

1.5

5.0

REMARK: The sum of the measured emission value and respective measuring inaccuracy rep-

resents the upper limit of the values that can occur during measuring.

Wear hearing protection!

Measured values determined in accordance with the corresponding product standard.

OBJ_BUCH-0000000252-002.book Page 7 Friday, July 14, 2017 9:34 AM

8

en

Symbols.

Symbol, character Explanation

Do not touch the rotating parts of the power tool.

Make sure to read the enclosed documents such as the Instruction Man-

ual and the General Safety Instructions.

Observe the instructions in the text or graphic opposite!

Before commencing this working step, remove the battery from the

power tool. Otherwise there may be danger of injury caused by unin-

tentional starting of the power tool.

Use eye protection during operation.

Use ear protection during operation.

Use protective gloves during operation.

Caution: Do not look or stare into the switched-on lamp!

General prohibition sign. This action is prohibited.

Do not charge damaged batteries.

Keep the battery away from fire. Protect the battery against heat, e. g.

against continuous intense sunlight.

Observe the notes in the text aside!

Switching on

Switching off

Confirms the conformity of the power tool with the guidelines of the

European Community.

This symbol confirms the certification of this product for the USA and

Canada.

This sign warns of a directly imminent, dangerous situation. A false reac-

tion can cause a severe or fatal injury.

This sign indicates a possible dangerous situation that could cause severe

or fatal injury.

This sign warns of a possible dangerous situation that could cause injury.

Recycling code: identifies recyclable materials

Worn out power tools and other electrotechnical and electrical prod-

ucts should be sorted separately for environmentally-friendly recycling.

Battery type

Reduce torque

DANGER

WARNING

CAUTION

OBJ_BUCH-0000000252-002.book Page 8 Friday, July 14, 2017 9:34 AM

9

en

Increase torque

Apply retaining compound (medium tightness).

Allow retaining compound to cure according to the manufacturer's

instructions.

** may contain numbers and letters

Symbol, character Explanation

24

Character Unit of measurement, national Explanation

n

0

rpm; /min; min

-1

; r/min No-load speed

(Range adjustable with Parameter Control (PC)

software)

n

Reset

rpm; /min; min

-1

; r/min Speed (factory-set at delivery)

M...

Nm, lbf in Torque

P

W Electrical power

°Angle width

U V Electric voltage

f Hz Frequency

I

A Electric current intensity

m

kg, lbs Mass

l ft, in Length, width, height, depth, diameter or

thread

Ø ft, in Diameter of a round part

K...

Uncertainty

m/s

2

, ft/s

2

Vibrational emission value according to

EN 60745 (vector sum of three directions)

m, s, kg, A, mm, V, W, Hz, N,

°C, dB, min, m/s

2

Basic and derived units of measurement from

the international system of units SI.

OBJ_BUCH-0000000252-002.book Page 9 Friday, July 14, 2017 9:34 AM

10

en

Technical description and specifications.

Before mounting or replacing application tools or accessories, remove the bat-

tery. This preventive safety measure rules out the danger of injuries through

accidental starting of the power tool.

Not all accessories described or shown in this instruction manual will be included with your-

power tool.

WARNING

Rotational direction switch

Cover

Tool holder

Light

On/Off switch

Battery

Gripping surface

Fig. 1

LED indication

LED indication on battery

Battery-Unlocking button

ASW 18-18/ASW 18-18 PC/ASW 18-30PC

ASW18-45 PC/ASW 18-60 PC

OBJ_BUCH-0000000252-002.book Page 10 Friday, July 14, 2017 9:34 AM

11

en

Rotational direction switch

Cover

Tool holder

Light

On/Off switch

Battery

Gripping surface

Fig. 2

LED indication

LED indication on battery

Battery-Unlocking button

ASW 18-6/ASW 18-6 PC

ASW18-12/ASW 18-12 PC

OBJ_BUCH-0000000252-002.book Page 11 Friday, July 14, 2017 9:34 AM

12

en

Type ASW18-30 PC (**) ASW18-45 PC (**) ASW18-60 PC (**)

Order number 7 112 ... 7 112 ... 7 112 ...

Rated voltage 14.4–18.0 14.4–18.0 14.4–18.0

Rated speed 30 – 420 /min 25 – 310 /min 20 – 230 /min

Speed (factory-set at delivery) 180 /min 130 /min 100 /min

Torque 30 Nm

265 lbf in

45 Nm

398.3 lbf in

60 Nm

531.0 lbf in

Weight according to EPTA-Pro-

cedure 01 3.31 lbs (1.5 kg) 3.31 lbs (1.5 kg) 3.64 lbs (1.65 kg)

Type B14A B18A

Battery type Lithium ion (Li ion) Lithium ion (Li ion)

Rated voltage 14.4 V 18.0 V

Weight according to EPTA-Procedure 01

(Battery)

1.32 lbs (0.6 kg) 1.54 lbs (0.7 kg)

Type ASW18-6

(**)

ASW18-12

(**)

ASW18-18

(**)

ASW18-6PC

(**)

ASW18-

12PC (**)

ASW18-

18PC (**)

Order number 7 112 ... 7 112 ... 7 112 ... 7 112 ... 7 112 ... 7 112 ...

Rated voltage 12.0–18.0 12.0–18.0 12.0–18.0 12.0–18.0 12.0–18.0 12.0–18.0

Rated speed 100 – 1300

/min

75–1000

/min

65 – 900

/min

Speed (factory-set at

delivery)

575 /min 430 /min 375 /min 575 /min 430 /min 375 /min

Torque 6 Nm

53.1 lbf in

12 Nm

106.2 lbf in

18 Nm

159.3 lbf in

6 Nm

53.1 lbf in

12 Nm

106.2 lbf in

18 Nm

159.3 lbf in

Weight according to

EPTA-Procedure 01

2.20 lbs

(1.0 kg)

2.20 lbs

(1.0 kg)

2.64 lbs

(1.2 kg)

2.20 lbs

(1.0 kg)

2.20 lbs

(1.0 kg)

2.64 lbs

(1.2 kg)

Type B12A B14A B14A B18A B18A

Battery type Lithium ion

(Li ion)

Lithium ion

(Li ion)

Lithium ion

(Li ion)

Lithium ion

(Li ion)

Lithium ion

(Li ion)

Rated voltage 12 V 14.4 V 14.4 V 18.0 V 18.0 V

Weight according

to EPTA-Procedure

01 (Battery)

0.55 lbs

(0.25 kg)

0.88 lbs

(0.4 kg)

1.32 lbs

(0.6 kg)

1.0 lbs

(0.45 kg)

1.54 lbs

(0.7 kg)

OBJ_BUCH-0000000252-002.book Page 12 Friday, July 14, 2017 9:34 AM

13

en

Assembly instructions.

Before mounting or replacing application tools or accessories, remove the bat-

tery. This preventive safety measure rules out the danger of injuries through

accidental starting of the power tool.

Removing and charging the battery

(figure 3).

Prior to the first charging procedure,

read the operating instructions of the

battery charger.

Charge the battery completely before

putting into operation for the first time.

Release the battery by pressing the battery

unlocking button and pull the battery out of

the handle. Do not exert any force when

doing this.

Connect the battery charger to a socket out-

let, slide the battery onto the battery charger

and charge the battery. After the charging

process is over, insert the battery into the

power tool and pull the plug of the battery

charger out of the socket outlet.

A new battery does not reach its full capacity

until after several charging and discharging

procedures.

WARNING

1.

2.

Fig. 3

Battery

Battery-Unlocking button

OBJ_BUCH-0000000252-002.book Page 13 Friday, July 14, 2017 9:34 AM

14

en

Mounting the angle head (ASW 18-6/ASW 18-6 PC/ASW 18-12/ASW 18-12 PC)

(figure 4).

Release the clamping sleeve and remove it.

Clean the mounting surface using a clean

cloth.

Pay attention that the threads are grease-

free before applying the retaining com-

pound.

Mount the clamping sleeve again and fasten it.

Screw the angle head into the clamping

sleeve.

Fig. 4

1.

2.

5.

3.

4.

4 mm

6.

OBJ_BUCH-0000000252-002.book Page 14 Friday, July 14, 2017 9:34 AM

15

en

Aligning the angle head (ASW 18-6/ASW 18-6 PC/ASW 18-12/ASW 18-12 PC)

(figure 5).

Adjust the desired angle-head work angle and

then lock it by tightening the clamping sleeve.

M = 15 - 20 Nm

1.

2.

Fig. 5

OBJ_BUCH-0000000252-002.book Page 15 Friday, July 14, 2017 9:34 AM

16

en

Mounting the angle head (ASW 18-18/ASW 18-18 PC/ASW 18-30 PC/

ASW 18-45 PC/ASW 18-60 PC) (figure 6).

Loosen the clamping sleeve with the hook

wrench and remove it.

Clean the mounting surface using a clean cloth

and a degreasing solvent. Apply retaining

compound to the threads.

Pay attention that the threads are grease-

free before applying the retaining com-

pound.

Slide the clamping sleeve onto the angle head

and then fasten the securing ring.

Mount the angle head to the neck of the

power tool and pull the clamping sleeve

toward the rear. Lock the clamping sleeve

with the hook wrench.

Additional information: Further information

on replacement of the output can be found

on the Internet under www.fein.com.

1.

2.

3.

5.

4.

7.

8.

9.

6.

ASW 18-30 PC

ASW 18-45 PC

ASW 18-60 PC

6.

ASW 18-18

ASW 18-18 PC

M = 15-20 Nm

10.

24

6 29 08 014 00 0

Clamping sleeve

Hook spanner

Fig. 6

Angle head

Clamping ring

OBJ_BUCH-0000000252-002.book Page 16 Friday, July 14, 2017 9:34 AM

17

en

Mounting the extension (ASW 18-30 PC/ASW 18-45 PC/ASW 18-60 PC)

(optional accessory) (figure 7).

Loosen the clamping sleeve with the hook

wrench and remove the angle head.

Fasten the motor-shaft extension.

Mount the extension and lock it using the

hook wrench.

Slide the locking sleeve into the extension

and mount the connector onto the motor-

shaft extension.

Clean the mounting surface using a clean cloth

and a degreasing solvent. Apply retaining

compound to the threads.

Pay attention that the threads are grease-

free before applying the retaining com-

pound.

Mount the angle head onto the extension and

lock the clamping sleeve using the hook

wrench.

Additional information: Further information

on replacement of the output can be found

on the Internet under www.fein.com.

1.

2.

3.

6.

7.

8.

10.

11.

M = 15-20 Nm

9.

3/8”

1/2”

Fig. 7

5.

4.

6 29 08 014 00 0

Extension

Fig. 3

Angle head

Motor-shaft extension

Clamping sleeve

Hook spanner

Locking sleeve

Connector

OBJ_BUCH-0000000252-002.book Page 17 Friday, July 14, 2017 9:34 AM

18

en

Adjustments.

Before mounting or replacing application tools or accessories, remove the bat-

tery. This preventive safety measure rules out the danger of injuries through

accidental starting of the power tool.

Setting the torque (figure 8).

Before putting the power tool into operation

for the first time, the torque must be set to

the exact value and checked. The power tool

is not preset by the the manufacturer.

Open the cover using a screwdriver.

Turn the tool holder until the hole can be

seen under the cover.

Adjust the desired torque with the torque

setting tool.

Turn in the direction of the “+” to increase

the torque.

Turn in the direction of the “–” to reduce the

torque.

Shut the cover again.

WARNING

Fig. 8

1.

2.

3.

4.

3 21 23 002 00 6

5.

OBJ_BUCH-0000000252-002.book Page 18 Friday, July 14, 2017 9:34 AM

19

en

Selecting the rotation direction

(figure 9).

Adjust the rotation selector switch only when

the machine is at a complete stop.

To avoid accidental starting, e. g., during

transport, set the rotation selector switch to

the centre position.

Set the rotation selector switch to right or left

rotation as required.

Fig. 9

Rotational direction switch

OBJ_BUCH-0000000252-002.book Page 19 Friday, July 14, 2017 9:34 AM

20

en

Working instructions.

Before mounting or replacing application tools or accessories, remove the bat-

tery. This preventive safety measure rules out the danger of injuries through

accidental starting of the power tool.

Do not use accessories not specifically intended and recommended for this power tool by FEIN.

The use of non-original FEIN accessories can lead to overheating of the power tool and destroy

it.

For each job, use only the FEIN application tool released and intended for the

respective application.

Switching on and off (figure 10).

Always hold the power tool

firmly. Otherwise, you could

lose control over the power tool.

The power tool is equipped with a soft-start-

ing feature.

If the motor switches off after a proper

screwdriving operation, restarting is not pos-

sible until after 0.8 seconds. This prevents

accidental retightening of already tightened

screws.

In left rotation mode, the

power tool switches off with

significantly increased torque. Before putting

into operation, set the torque within the

specified limits on a suitable test bench.

Switching on:

To switch the power tool on after changing

the battery or after it having switched off,

press the switch for at least 0.2 seconds.

The operational readiness is signalled by the

lit LED.

When pressing the On/Off switch halfway in,

the light goes on.

When pressing the On/Off switch completely

in, the light and the power tool are on.

Switching off:

To switch off the power tool, release the

On/Off switch.

The power tool switches off approx. 30 min

after the last switch actuation, meaning, the

power tool can only be reactivated again by

switching on.

WARNING

CAUTION

Fig. 10

OBJ_BUCH-0000000252-002.book Page 20 Friday, July 14, 2017 9:34 AM

La page charge ...

FEIN ASW 18-6 PC Manuel utilisateur

FEIN ASW 18-6 PC Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents